82C55. Programmable Peripheral Interface. Interfacing Part III
|
|
|
- Avis Barber
- 5 years ago
- Views:
Transcription
1 82C55 Programmable Peripheral Interface Interfacing Part III
2 Review More on Address decoding Interface with memory Introduction to Programmable Peripheral Interface 82C55
3 About 82C55 The 82C55 is a popular interfacing component, that can interface any TTLcompatible I/O device to a microprocessor. It is used to interface to the keyboard and a parallel printer port in PCs (usually as part of an integrated chipset). Requires insertion of wait states if used with a microprocessor using higher that an 8 MHz clock. PPI has 24 pins for I/O that are programmable in groups of 12 pins and has three distinct modes of operation.
4 82C55 : Pin Layout
5 Basic Mode Definitions and Bus Int Mode 0 Basic I/O Mode 1 Strobe I/O Mode 2 Bi-Dir Bus
6 Programming 82C55
7 Mode 0 (Basic Input/Output). This functional configuration provides simple input and output operations for each of the three ports. No handshaking is required, data is simply written to or read from a specified port.
8 Mode 0 Port definition
9 82C55: Mode 0, Scan Display
10 82C55: Mode 0, Scan Display Mode 0 operation causes the 82C55 to function as a buffered input device or as a latched output device. In previous example, both ports A and B are programmed as (mode 0) simple latched output ports. Port A provides the segment data inputs to display and port B provides a means of selecting one display position at a time. Different values are displayed in each digit via fast time multiplexing.
11 82C55: Mode 0, Scan Key
12 82C55: Mode 0 Operation
13 MODE 1 (Strobed Input/Output) This functional configuration provides a means for transferring I/O data to or from a specified port in conjunction with strobes or handshaking signals. In mode 1, Port A and Port B use the lines on Port C to generate or accept these handshaking signals
14 Mode 1 Basic functional Definitions Two Groups (Group A and Group B). Each group contains one 8-bit data port and one 4-bit control/data port. The 8-bit data port can be either input or output Both inputs and outputs are latched. The 4-bit port is used for control and status of the 8-bit data port.
15 82C55: Mode 1 Strobed Input ~STB : The strobe input loads data into the port latch on a 0-to-1 transition. IBF : Input buffer full is an output indicating that the input latch contain information. INTR : Interrupt request is an output that requests an interrupts. INTE : The interrupt enable signal is neither an input nor an output; it is an internal bit programmed via the PC4 (port A) or PC2 (port B) bits. PC7,PC6 : The port C pins 7 and 6 are general purpose I/O pings that are available for any purpose.
16 82C55: Mode 1 Strobed Input Signal definitions for Mode 1 Strobe Input
17 82C55: Mode 1 Input Exam. Keyboard encoder debounces the key-switches, and provides a strobe whenever a key is depressed. DAV is activated on a key press strobing the ASCII-coded key code into Port A.
18 82C55 : Mode 1 Output Exam. ~OBF : Output buffer full is an output that goes low when data is latched in either port A or port B. Goes low on ~ACK. ~ACK : The acknowledge signal causes the ~OBF pin return to 0. This is a response from an external device. INTR : Interrupt request is an output that requests an interrupt. INTE : The interrupt enable signal is neither an input nor an output; it is an internal bit programmed via the PC6(Port A) or PC2(port B) bits. PC5,PC4 : The port C pins 5 and 4 are general-purpose I/O pins that are available for any purpose.
19 82C55 : Mode 1 Output Exam.
20 82C55: Mode 2 Bi-directional Operation This functional configuration provides a means for communicating with a peripheral device or structure on a single 8-bit bus for both transmitting and receiving data (bidirectional bus I/O). Handshaking signals are provided to maintain proper bus flow discipline in a similar manner to MODE 1. Interrupt generation and enable/disable functions are also available.
21 MODE 2 Basic Functional Definitions: Used in Group A only. One 8-bit, bi-directional bus port (Port A) and a 5-bit control port (Port C). Both inputs and outputs are latched. The 5-bit control port (Port C) is used for control and status for the 8-bit, bidirectional bus port (Port A).
22 82C55: Mode 2 Bi-directional Operation INTR : Interrupt request is an output that requests an interrupt. ~OBF : Output Buffer Full is an output indicating that that output buffer contains data for the bi-directional bus. ~ACK : Acknowledge is an input that enables tri-state buffers which are otherwise in their high-impedance state. ~STB : The strobe input loads data into the port A latch.
23 82C55: Mode 2 Bi-directional Operation IBF : Input buffer full is an output indicating that the input latch contains information for the external bidirectional bus. INTE : Interrupt enable are internal bits that enable the INTR pin. BIT PC6(INTE1) and PC4(INTE2). PC2,PC1,PC0 : These port C pins are general-purpose I/O pins that are available for any purpose.
24 82C55: Mode 2 Bi-directional Operation Timing diagram is a combination of the Mode 1 Strobed Input and Mode 1 Strobed Output Timing diagrams.
25 Mode 2 Timing Diagram
26 Mode definition summary
27 More on interface, next time.
Page 1 of 18 Hardware Training Tools Data Acquisition I/O Cards Development Tools Pic Tutor 8255 CHIPS Software CAD Education Consulting Downloads PRICE LIST Corporate About AMS Chronology Contact Sales
General Purpose Programmable Peripheral Devices. Assistant Professor, EC Dept., Sankalchand Patel College of Engg.,Visnagar
Chapter 15 General Purpose Programmable Peripheral Devices by Rahul Patel, Assistant Professor, EC Dept., Sankalchand Patel College of Engg.,Visnagar Microprocessor & Interfacing (140701) Rahul Patel 1
PIO 8255 (cont..) M Krishna kumar MAM/M3/LU9e/V1/2004 1
PIO 8255 (cont..) The parallel input-output port chip 8255 is also called as programmable peripheral input-output port. The Intel s 8255 is designed for use with Intel s 8-bit, 16-bit and higher capability
CHAPTER: 3 PROGRAMMABLE PERIPHERAL INTERFACE & ELECTROMECHANICAL DEVICES INTERFACING
CHAPTER: 3 1 PROGRAMMABLE PERIPHERAL INTERFACE & ELECTROMECHANICAL DEVICES INTERFACING Introduction to 8255 PPI 2 The Intel 8255A is a high-performance, general purpose programmable I/O device is designed
Lecture-53 Mode 2: (Strobed Bidirectional bus I/O) This functional configuration provides means for communicating with a peripheral device on a
Lecture-53 Mode 2: (Strobed Bidirectional bus I/O) This functional configuration provides means for communicating with a peripheral device on a single 8-bit I/O data bus in both directions, i.e., for both
Microcontroller interfaces
Microcontroller interfaces 1 Microcontroller interfaces Microcontroller interfaces Digital Analog Serial Parallel Binary (on/off) Voltage Current Asynchronous Synchronous 1-wire RS232/485 Ethernet 2-wire
Basic I/O Interface
Basic I/O Interface - 8255 11 3 THE PROGRAMMABLE PERIPHERAL 82C55 programmable peripheral interface (PPI) is a popular, low-cost interface component found in many applications. The PPI has 24 pins for
INTRO TO I/O INTERFACE
Basic I/O Interface Introduction This chapter outlines some of the basic methods of communications, both serial and parallel, between humans or machines and the microprocessor. We first introduce the basic
Programmable Peripheral Interface (PPI) 8255A. CEN433 King Saud University Dr. Mohammed Amer Arafah
Programmable Peripheral Interface (PPI) 8255A CEN433 King Saud University Dr. 1 Functional Diagram 2 Pin Description 3 8255A Basic Operation A 1 A 0 Port 0 0 Port A 0 1 Port B 1 0 Port C 1 1 Control Word
Segment A Programmable Peripheral Interface (PPI)
Segment 6 8255A Programmable Peripheral Interface (PPI) Content Why 8255A? Handshaking and Handshaking Signal Parallel Data Transfer 8255A Internal Block Diagram Description of 8255A Internal Block Diagram
9. PERIPHERAL CHIPS 9a
9. PERIPHERAL CHIPS 9a 8255: Programmable Peripheral Interface. Draw the pin diagram of PPI 8255. Ans. The pin diagram of 8255 is shown in Fig. 9a. PA 3 4 PA 4 PA2 2 39 PA 5 PA 3 38 PA 6 PA 4 37 PA7 RD
8255 Programmable Peripheral Interface Architecture MCT/UNIT III/NARASIMHARAJ/LECTURE NOTES /IV MECH A
8255 Programmable Peripheral Interface Architecture 8255 PPI Architecture The parallel input-output port chip 8255 is also called as programmable peripheral input- output port. The Intel s 8255 is designed
Week 7. Input/Output Interface Circuits and LSI Peripheral Devices
Week 7 Input/Output Interface Circuits and LSI Peripheral Devices Core and Special Purpose I/O Interfaces Special purpose I/O interfaces display parallel printer interface serial communication interface
1. What is Microprocessor? Give the power supply & clock frequency of 8085?
1. What is Microprocessor? Give the power supply & clock frequency of 8085? A microprocessor is a multipurpose, programmable logic device that reads binary instructions from a storage device called memory
EC2304-MICROPROCESSOR AND MICROCONROLLERS 2 marks questions and answers UNIT-I
EC2304-MICROPROCESSOR AND MICROCONROLLERS 2 marks questions and answers 1. Define microprocessors? UNIT-I A semiconductor device(integrated circuit) manufactured by using the LSI technique. It includes
a8255 Features General Description Programmable Peripheral Interface Adapter
a8255 Programmable Peripheral Interface Adapter September 1996, ver. 1 Features a8255 MegaCore function implementing a programmable peripheral interface adapter Optimized for FLEX and MAX architectures
The Purpose of Interrupt
Interrupts 3 Introduction In this chapter, the coverage of basic I/O and programmable peripheral interfaces is expanded by examining a technique called interrupt-processed I/O. An interrupt is a hardware-initiated
I/O Design. Input / Output Instructions. Engineering 4862 Microprocessors. Lecture 23. Cheng Li
Engineering 4862 Microprocessors Lecture 23 Cheng Li EN-4012 licheng@engr.mun.ca I/O Design When designing an I/O port, ensure that the port is only active when selected by the microprocessor Use latches
4 Multiplexer. Y Fig Keyboard Scan Matrix
- 4 Multiplexer Microcontroller 3 Decoder X Y Fig. - Keyboard Scan Matrix 2 Prentice Hall, Inc. -2 Track Sector Head positioning Fig. -2 Hard Disk Format 2 Prentice Hall, Inc. -3 RGB electron guns R G
EC6504-MP&MC, UNIT3 Page 1
Year/sem: 02/04 UNIT III I/O INTERFACING Academic Year: 2014-2015 (even) 1. What is interfacing? An interface is a shared boundary between the devices which involves sharing information. Interfacing is
The 8255A: Programmable Peripheral Interface
CMP:885 Peripherals Summary- EE39: Computer Organization, rchitecture and MicroProcessors http://www.ee.iitb.ac.in/ sumantra/courses/up/up.html The 855: Programmable Peripheral Interface PROGRMMER S VIEW
Summer 2003 Lecture 21 07/15/03
Summer 2003 Lecture 21 07/15/03 Simple I/O Devices Simple i/o hardware generally refers to simple input or output ports. These devices generally accept external logic signals as input and allow the CPU
UNIT - II PERIPHERAL INTERFACING WITH 8085
UNIT - II PERIPHERAL INTERFACING WITH 8085 Peripheral Interfacing is considered to be a main part of Microprocessor, as it is the only way to interact with the external world. The interfacing happens with
MICROPROCESSOR TECHNOLOGY
MICROPROCESSOR TECHNOLOGY Assis. Prof. Hossam El-Din Moustafa Lecture 12 Ch.5 8086/8088 Hardware Specifications 22-Mar-15 1 The Buffered System If more than 10 unit loads are attached to any bus pin, the
CHMOS PROGRAMMABLE PERIPHERAL INTERFACE
CHMOS PROGRMMLE PERIPHERL INTERFCE TECHNICL DT IN2C55 The Integral IN2C55N is a high-performance, CHMOS version of the industry standard IN2C55N general purpose programmable I/O device which is designed
Topics. Interfacing chips
8086 Interfacing ICs 2 Topics Interfacing chips Programmable Communication Interface PCI (8251) Programmable Interval Timer (8253) Programmable Peripheral Interfacing - PPI (8255) Programmable DMA controller
ROEVER ENGINEERING COLLEGE
ROEVER ENGINEERING COLLEGE ELAMBALUR, PERAMBALUR- 621 212 DEPARTMENT OF INFORMATION TECHNOLOGY MICROPROCESSOR & MICROCONTROLLER 2 marks questions andanswers Unit I 1. Define microprocessor? A microprocessor
Features: 3 8-bit IO ports PA, PB, PC. PA can be set for Modes 0, 1, 2. PB for 0,1 and PC for mode 0 and for BSR. Modes 1 and 2 are interrupt driven.
Features: 3 8-bit IO ports PA, PB, PC PA can be set for Modes, 1, 2. PB for,1 and PC for mode and for BSR. Modes 1 and 2 are interrupt driven. PC has 2 4-bit parts: PC upper (PCU) and PC lower (PCL), each
Lecture-51 INTEL 8259A Programmable Interrupt Controller
Lecture-51 INTEL 8259A Programmable Interrupt Controller The 8259A is a programmable interrupt controller designed to work with Intel microprocessor 8080 A, 8085, 8086, 8088. The 8259 A interrupt controller
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI UNIT IV I/O INTERFACING PART A (2 Marks)
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI-621213. UNIT IV I/O INTERFACING PART A (2 Marks) 1. Name the three modes used by the DMA processor to transfer data? [NOV/DEC 2006] Signal transfer mode (cycling
Pin Description, Status & Control Signals of 8085 Microprocessor
Pin Description, Status & Control Signals of 8085 Microprocessor 1 Intel 8085 CPU Block Diagram 2 The 8085 Block Diagram Registers hold temporary data. Instruction register (IR) holds the currently executing
PIN DIAGRAM. Richa Upadhyay Prabhu. NMIMS s MPSTME January 19, 2016
PIN DIAGRAM Richa Upadhyay Prabhu NMIMS s MPSTME richa.upadhyay@nmims.edu January 19, 2016 Richa Upadhyay Prabhu (MPSTME) 8080 Microprocessor January 19, 2016 1 / 51 Pin Diagram of 8086 Richa Upadhyay
C13. INTERFATA PARALELA PROGRAMABILA (PPI) I8255A (PIO)
C13. INTERFATA PARALELA PROGRAMABILA (PPI) I8255A (PIO) 1.Descriere PIO 2. Arhitectura PIO 3. Programare PIO 4. PIO in PC 5. Aplicatii http://www.advancedmsinc.com/iocards/8255.htm http://www.eisti.fr/~ga/phy/iitr/ii05/tr.pdf
Chapter 13 Direct Memory Access and DMA-Controlled I/O
Chapter 13 Direct Memory Access and DMA-Controlled I/O The DMA I/O technique provides direct access to the memory while the microprocessor is temporarily disabled This allows data to be transferred between
Z Z-280 MT8930, MT8992/3/4/5 MT8880 MT8888 MT8889 MT8980/1 MT8985, MT8986 (DIP-40) MT8986 (PLCC-44) MT8920B MT8952B
MSAN-145 How to Interface Mitel Components to Parallel Bus CPUs TABL OF CONTNTS Introduction ISSU 1 August 1993 1.0 Group 1 Components 1.1 Interfacing to the 6802 1.2 Interfacing to the 6809 1.3 Interfacing
UNIT III. 2. Non-maskable interrupts. 3. Software interrupt. 4. Internal interrupt
UNIT III 8086 INTERRUPTS: An interrupt is the method of processing the microprocessor by peripheral device. An interrupt is used to cause a temporary halt in the execution of program. Microprocessor responds
Interfacing Fundamentals
CHAPTER Interfacing Fundamentals 3.1 Introduction There is no doubt that the microcomputer revolution will continue into the future and many will be required to specify and integrate microprocessors into
80C451 operation of port 6
INTRODUCTION The features of the are shared with the 80C5 or are conventional except for the operation of port 6. The flexibility of this port facilitates high-speed parallel data communications. This
These three counters can be programmed for either binary or BCD count.
S5 KTU 1 PROGRAMMABLE TIMER 8254/8253 The Intel 8253 and 8254 are Programmable Interval Timers (PTIs) designed for microprocessors to perform timing and counting functions using three 16-bit registers.
Chapter NINE 8088,80286 MICROPROCESSORS AND ISA BUS
Chapter NINE 8088,80286 MICROPROCESSORS AND ISA BUS OBJECTIVES this chapter enables the student to: State the function of the pins of the 8088. List the functions of the 8088 data, address, and control
UMBC. 80C86/80C88: CMOS version draws 10mA with temp spec -40 to 225degF. 450mV while input max can be no higher than 800mV). 0 0.
8086/88 Device Specifications Both are packaged in DIP (Dual In-Line Packages). 8086: 16-bit microprocessor with a 16-bit data bus 8088: 16-bit microprocessor with an 8-bit data bus. Both are 5V parts:
This set of Microprocessor Multiple Choice Questions & Answers (MCQs) focuses on PIO 8255 (Programmable Input Output Port).
This set of Microprocessor Multiple Choice Questions & Answers (MCQs) focuses on PIO 8255 (Programmable Input Output Port). 1. Programmable peripheral input-output port is other name for a) serial input-output
INTERFACING INTERFACING. Richa Upadhyay Prabhu. NMIMS s MPSTME February 25, 2016
INTERFACING Richa Upadhyay Prabhu NMIMS s MPSTME richa.upadhyay@nmims.edu February 25, 2016 8255: Programmable Peripheral Interface or Programmable Input output Device Introduction METHODS OF DATA TRANSFER
PROGRAMMABLE PERIPHERAL INTERFACE (PPI) -8255
PROGRAMMABLE PERIPHERAL INTERFACE (PPI) -8255 8255 is a general purpose programmable device used for data transfer between processor and I/O devices. It has 3 programmable I/O ports (PA,PB &PC) and port
MICROPROCESSOR MICROPROCESSOR. From the above description, we can draw the following block diagram to represent a microprocessor based system: Output
8085 SATISH CHANDRA What is a Microprocessor? The word comes from the combination micro and processor. Processor means a device that processes whatever. In this context, processor means a device that processes
8086 Hardware Specification
Content: Segment 5 8086 Hardware Specification 8086 Modes of operation. Pin diagram and pin function of 8086. 8284A Clock generator operation and pin functions. Prepared By: Mohammed Abdul Kader Lecturer,
INTRODUCTION OF MICROPROCESSOR& INTERFACING DEVICES Introduction to Microprocessor Evolutions of Microprocessor
Course Title Course Code MICROPROCESSOR & ASSEMBLY LANGUAGE PROGRAMMING DEC415 Lecture : Practical: 2 Course Credit Tutorial : 0 Total : 5 Course Learning Outcomes At end of the course, students will be
S.R.M. INSTITUTE OF SCIENCE & TECHNOLOGY SCHOOL OF ELECTRONICS & COMMUNICATION ENGINEERING
S.R.M. INSTITUTE OF SCIENCE & TECHNOLOGY SCHOOL OF ELECTRONICS & COMMUNICATION ENGINEERING QUESTION BANK Subject Code : EC307 Subject Name : Microprocessor and Interfacing Year & Sem : III Year, V Sem
Lecture-50 Intel 8255A: Programming and Operating Modes
Lecture-50 Intel 8255A: Programming and Operating Modes Operation Description: There are three basic modes of operation that can be selected by the system software. Mode 0: Basic Input/output Mode 1: Strobes
8051 Microcontroller
8051 Microcontroller 1 Salient Features (1). 8 bit microcontroller originally developed by Intel in 1980. (2). High-performance CMOS Technology. (3). Contains Total 40 pins. (4). Address bus is of 16 bit
MICROPROCESSOR AND MICROCONTROLLER BASED SYSTEMS
MICROPROCESSOR AND MICROCONTROLLER BASED SYSTEMS UNIT I INTRODUCTION TO 8085 8085 Microprocessor - Architecture and its operation, Concept of instruction execution and timing diagrams, fundamentals of
The MC9S12 address, data and control buses The MC9S12 single-chip mode memory map Simplified write/read cycle. Address, Data and Control Buses
EE 308 Spring 2013 The MC9S12 address, data and control buses The MC9S12 single-chip mode memory map Simplified write/read cycle The real MC9S12 multiplexed external bus Byte order in microprocessors How
INTEGRATED CIRCUITS. AN408 80C451 operation of port 6
INTEGRATED CIRCUITS March 1988 INTRODUCTION The features of the are shared with the 80C51 or are conventional except for the operation of port 6. The flexibility of this port facilitates high-speed parallel
Basics of Microprocessor
Unit 1 Basics of Microprocessor 1. Microprocessor Microprocessor is a multipurpose programmable integrated device that has computing and decision making capability. This semiconductor IC is manufactured
1. Internal Architecture of 8085 Microprocessor
1. Internal Architecture of 8085 Microprocessor Control Unit Generates signals within up to carry out the instruction, which has been decoded. In reality causes certain connections between blocks of the
1. INTRODUCTION TO MICROPROCESSOR AND MICROCOMPUTER ARCHITECTURE:
1. INTRODUCTION TO MICROPROCESSOR AND MICROCOMPUTER ARCHITECTURE: A microprocessor is a programmable electronics chip that has computing and decision making capabilities similar to central processing unit
Input/Output Ports and Interfacing
Input/Output Ports and Interfacing ELEC 330 Digital Systems Engineering Dr. Ron Hayne Images Courtesy of Ramesh Gaonkar and Delmar Learning Basic I/O Concepts Peripherals such as LEDs and keypads are essential
PCI based dual UART and printer port chip CH352
The DataSheet of CH352 (the second) 1 1. Package PCI based dual UART and printer port chip CH352 UART+parallel/printer port the second DataSheet: UART+parallel Version: 1A http://wch.cn UART+8255 parallel
1 MALP ( ) Unit-1. (1) Draw and explain the internal architecture of 8085.
(1) Draw and explain the internal architecture of 8085. The architecture of 8085 Microprocessor is shown in figure given below. The internal architecture of 8085 includes following section ALU-Arithmetic
Lecture-9 Intel 8085 Microprocessor It is a 40-pin DIP(Dual in package) chip, base on NMOS technology, on a single chip of silicon.
Lecture-9 Intel 8085 Microprocessor It is a 40-pin DIP(Dual in package) chip, base on NMOS technology, on a single chip of silicon. It requires a single +5v supply between Vcc at pin no 40 and GND at pin
CHAPTER 5 : Introduction to Intel 8085 Microprocessor Hardware BENG 2223 MICROPROCESSOR TECHNOLOGY
CHAPTER 5 : Introduction to Intel 8085 Hardware BENG 2223 MICROPROCESSOR TECHNOLOGY The 8085A(commonly known as the 8085) : Was first introduced in March 1976 is an 8-bit microprocessor with 16-bit address
Microprocessors and Microcontrollers (EE-231)
Microprocessors and Microcontrollers (EE-231) Main Objectives 8088 and 80188 8-bit Memory Interface 8086 t0 80386SX 16-bit Memory Interface I/O Interfacing I/O Address Decoding More on Address Decoding
FIFTH SEMESTER B.TECH DEGREE EXAMINATION MODEL TEST QUESTION PAPER, NOVEMBER CS 305: Microprocessor and Microcontrollers PART A
Reg No Name FIFTH SEMESTER B.TECH DEGREE EXAMINATION MODEL TEST QUESTION PAPER, NOVEMBER 2017 CS 305: Microprocessor and Microcontrollers Max. Marks: 100 Duration: 3 Hours PART A Answer all questions.
Design with Microprocessors
Design with Microprocessors Year III Computer Science 1-st Semester Lecture 11: I/O transfer with x86 I/O Transfer I/O Instructions We discussed IN, OUT, INS and OUTS as instructions for the transfer of
Architecture of 8085 microprocessor
Architecture of 8085 microprocessor 8085 consists of various units and each unit performs its own functions. The various units of a microprocessor are listed below Accumulator Arithmetic and logic Unit
1 Digital tools. 1.1 Introduction
1 Digital tools 1.1 Introduction In the past few years, enormous advances have been made in the cost, power, and ease of use of microcomputers and associated analog and digital circuits. It is now possible,
Unit-IV Peripheral Interfacing S.Sayeekumar, AP/RMDEEE
Unit-IV Peripheral Interfacing S.Sayeekumar, AP/RMDEEE 8251 The 8251A is a programmable serial communication interface chip designed for synchronous and asynchronous serial data communication. It supports
DHANALAKSHMI COLLEGE OF ENGINEERING, CHENNAI DEPARTMENT OF COMPUTER SCIENCE AND ENGINEERING EC6504 MICROPROCESSOR AND MICRO CONTROLLER
DHANALAKSHMI COLLEGE OF ENGINEERING, CHENNAI DEPARTMENT OF COMPUTER SCIENCE AND ENGINEERING EC6504 MICROPROCESSOR AND MICRO CONTROLLER UNIT - I : THE 8086 MICROPROCESSOR PART A (2 Marks) 1. What are different
UNIT V MICRO CONTROLLER PROGRAMMING & APPLICATIONS TWO MARKS. 3.Give any two differences between microprocessor and micro controller.
UNIT V -8051 MICRO CONTROLLER PROGRAMMING & APPLICATIONS TWO MARKS 1. What is micro controller? Micro controller is a microprocessor with limited number of RAM, ROM, I/O ports and timer on a single chip
CPE/EE 421/521 Fall 2004 Chapter 4 The CPU Hardware Model. Dr. Rhonda Kay Gaede UAH. The CPU Hardware Model - Overview
CPE/EE 421/521 Fall 2004 Chapter 4 The 68000 CPU Hardware Model Dr. Rhonda Kay Gaede UAH Fall 2004 1 The 68000 CPU Hardware Model - Overview 68000 interface Timing diagram Minimal configuration using the
Microprocessor Architecture. mywbut.com 1
Microprocessor Architecture mywbut.com 1 Microprocessor Architecture The microprocessor can be programmed to perform functions on given data by writing specific instructions into its memory. The microprocessor
eaymanelshenawy.wordpress.com
Lectures on Memory Interface Designed and Presented by Dr. Ayman Elshenawy Elsefy Dept. of Systems & Computer Eng.. Al-Azhar University Email : eaymanelshenawy@yahoo.com eaymanelshenawy.wordpress.com Chapter
CPE/EE 421 Microcomputers
CPE/EE 421 Microcomputers THE 68000 CPU HARDWARE MODEL Instructor: Dr Aleksandar Milenkovic Lecture Notes Lecture 19 CPE/EE 421/521 Microcomputers 1 THE 68000 CPU HARDWARE MODEL Chapter 4 68000 interface
INTERFACING THE ISCC TO THE AND 8086
APPLICATION NOTE INTERFACING THE ISCC TO THE 68 AND 886 INTRODUCTION The ISCC uses its flexible bus to interface with a variety of microprocessors and microcontrollers; included are the 68 and 886. The
EC Microprocessor and Microcontroller
DMI COLLEGE OF ENGINEERING EC6504 - Microprocessor and Microcontroller UNIT I THE 8086 MICROPROCESSOR 1. What are different data transfer schemes? The different data transfer schemes are [A/M 12] 2. How
Chapter ELEVEN 8255 I/O PROGRAMMING
Chapter ELEVEN 8255 I/O PROGRAMMING OBJECTIVES this chapter enables the student to: Code Assembly language instructions to read and write data to and from I/O ports. Diagram the design of peripheral I/O
www.vidyarthiplus.com www.vidyarthiplus.com www.vidyarthiplus.com www.vidyarthiplus.com www.vidyarthiplus.com Time : Three hours Reg. No. : B.E./B.Tech. DEGREE EXAMINATION, APRIL/MAY 2011 Sixth
History and Basic Processor Architecture
History and Basic Processor Architecture History of Computers Module 1 Section 1 What Is a Computer? An electronic machine, operating under the control of instructions stored in its own memory, that can
MP Assignment III. 1. An 8255A installed in a system has system base address E0D0H.
MP Assignment III 1. An 8255A installed in a system has system base address E0D0H. i) Calculate the system addresses for the three ports and control register for this 8255A. System base address = E0D0H
EC1362 Microprocessors & Microcontrollers
Part A- Two Mark Questions 1. What is Microprocessor? It is a program controlled semiconductor device (IC}, which fetches, decodes and executes instructions. 2. What are the basic units of a microprocessor?
27 December 2016 Pramod Ghimire. Slide 1 of 16
8259-Programmable Interrupt Controller (8259-PIC) Slide 1 of 16 Programmable Interface Device A Programmable interface device is designed to perform various input/output functions. Such a device can be
QUIZ Ch.6. The EAT for a two-level memory is given by:
QUIZ Ch.6 The EAT for a two-level memory is given by: EAT = H Access C + (1-H) Access MM. Derive a similar formula for three-level memory: L1, L2 and RAM. Hint: Instead of H, we now have H 1 and H 2. Source:
Microprocessor Architecture
Microprocessor - 8085 Architecture 8085 is pronounced as "eighty-eighty-five" microprocessor. It is an 8-bit microprocessor designed by Intel in 1977 using NMOS technology. It has the following configuration
It is a program controlled semiconductor device (IC}, which fetches, decode and executes instructions.
1.What is Microprocessor? It is a program controlled semiconductor device (IC}, which fetches, decode and executes instructions. 2. What are the basic units of a microprocessor? The basic units or blocks
8085 Microprocessor Architecture and Memory Interfacing. Microprocessor and Microcontroller Interfacing
8085 Microprocessor Architecture and Memory 1 Points to be Discussed 8085 Microprocessor 8085 Microprocessor (CPU) Block Diagram Control & Status Signals Interrupt Signals 8085 Microprocessor Signal Flow
INPUT-OUTPUT ORGANIZATION
INPUT-OUTPUT ORGANIZATION Peripheral Devices: The Input / output organization of computer depends upon the size of computer and the peripherals connected to it. The I/O Subsystem of the computer, provides
The IIC interface based on ATmega8 realizes the applications of PS/2 keyboard/mouse in the system
Available online at www.sciencedirect.com Procedia Engineering 16 (2011 ) 673 678 International Workshop on Automobile, Power and Energy Engineering The IIC interface based on ATmega8 realizes the applications
PART B UNIT II PART A
SRM INSTITUTE OF SCIENCE AND TECHNOLOGY (Deemed University) DEPARTMENT OF COMPUTER SCIENCE AND ENGINEERING QUESTION BANK SUB : Microprocessor/CS201 YEAR/SEM : II/III UNIT I PART - A 1. Differentiate accumulator
Chapter 12: INTERRUPTS
Chapter 12: INTERRUPTS 12 1 BASIC INTERRUPT PROCESSING This section discusses the function of an interrupt in a microprocessor-based system. Structure and features of interrupts available to Intel microprocessors.
Section I Section Real Time Systems. Processes. 1.6 Input/Output Management. (Textbook: A. S. Tanenbaum Modern OS - ch. 5)
EE206: Software Engineering IV 1.6 Input/Output page 1 of 9 Section I Section Real Time Systems. Processes 1.6 Input/Output Management (Textbook: A. S. Tanenbaum Modern OS - ch. 5) Input/Output Overview
Ch 4. Standard Single Purpose Processors: Peripherals
EE414 Embedded Systems Ch 4. Standard Single Purpose Processors: Peripherals Part 2/5: Parallel Interface Byung Kook Kim School of Electrical Engineering Korea Advanced Institute of Science and Technology
CS2252 Microprocessor & Microcontroller TWO MARKS
CS2252 Microprocessor & Microcontroller TWO MARKS 1. What is Microprocessor? Give the power supply & clock frequency of 8085. A microprocessor is a multipurpose, programmable logic device that reads binary
Lecture Note On Microprocessor and Microcontroller Theory and Applications
Lecture Note On Microprocessor and Microcontroller Theory and Applications MODULE: 1 1. INTRODUCTION TO MICROPROCESSOR AND MICROCOMPUTER ARCHITECTURE: A microprocessor is a programmable electronics chip
2. List the five interrupt pins available in INTR, TRAP, RST 7.5, RST 6.5, RST 5.5.
DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE6502- MICROPROCESSORS AND MICROCONTROLLERS UNIT I: 8085 PROCESSOR PART A 1. What is the need for ALE signal in
Chapter 4 : Microprocessor System
Chapter-4 Microprocessor System A microcomputer consists of a set of components or modules of three basic types CPU memory and I/O units which communicate with each other. PIN Configuration of 8085 Fig
Microprocessors and Microcontrollers Prof. Santanu Chattopadhyay Department of E & EC Engineering Indian Institute of Technology, Kharagpur
Microprocessors and Microcontrollers Prof. Santanu Chattopadhyay Department of E & EC Engineering Indian Institute of Technology, Kharagpur Lecture - 09 8085 Microprocessors (Contd.) (Refer Slide Time:
8086 Interrupts and Interrupt Responses:
UNIT-III PART -A INTERRUPTS AND PROGRAMMABLE INTERRUPT CONTROLLERS Contents at a glance: 8086 Interrupts and Interrupt Responses Introduction to DOS and BIOS interrupts 8259A Priority Interrupt Controller
CS 1304-MICROPROCESSORS
CS 1304-MICROPROCESSORS 1. What is Microprocessor? Give the power supply & clock frequency of 8085 A microprocessor is a multipurpose, programmable logic device that reads binary instructions from a storage
The MC9S12 in Expanded Mode Using MSI logic to build ports Using MSI logic to build an output port Using MSI logic to build an input port
The MC9S12 in Expanded Mode Using MSI logic to build ports Using MSI logic to build an output port Using MSI logic to build an input port A Simple Parallel Output Port We want a port which will write 8
MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) MODEL ANSWER
MODEL ANSWER SUMMER 17 EXAMINATION Subject Title: Microprocessor Subject Code: 17443 I m p o r t a n t I n s t r u c t i o n s t o e x a m i n e r s : 1) The answers should be examined by key words and