Notice of Intended Single/Sole Source Purchase

Transcription

1 Notice of Intended Single/Sole Source Purchase To all Suppliers and/or Contractors: The following product or service listed below may be a Sole Source or a Single Source (only One source from which to purchase the product/service). Description of Intended Single/Sole Source Purchase: This description of commodities or contractual services intended for purchase from a single/sole source is posted in accordance with Florida Administrative Rule 6A will remain posted for a period of seven (7) business days. Failure to file a protest within the time prescribed in section (3), Florida Statutes, or failure to post the bond or other security required by law within the time allowed for filing a bond shall constitute a waiver of proceedings under chapter 120, Florida Statutes. SS# 17-SS-045-WH Posting Date: 11/22/2017 Product/Service: Manufacturer: Vendor: FRYER CL-12, FRYER CM-15 FYRER Machine Solutions Florida Machine Tool Sales Dollar Amount (if applicable): $75, Term of Agreement - one-time purchase If you believe you have a like product or have a like service, please contact Wil Henzmann, Buyer in Purchasing Services at ext.623. Like shall mean equal, equivalent, and/or identical. If Purchasing Services does not receive like product/service information during the posting period, the purchase order shall be issued to the listed vendor. Page 1 of 1

2

3 FRYER CL 12 CNC TURNING CENTER MINIMUM REQUIREMENTS MACHINE CAPACITY SPINDLE GENERAL INFORMATIONPERFORMANCE Swing Over Bed 12" Swing Over Cross Slide 6" Center Height 6.5" Distance Between Centers 8" Width of Bed 8" Width of Cross Slide 4" Cross Slide Travel (X) 6" Longitudinal Travel (Z) 10" Ball Screw Size Z ", X.787" Max Part Weight - Unsupported 100 lbs Max Part Weight - Supported with S/R 200 lbs Spindle Nose D1-4 Spindle Bore 1.57" Spindle Nose Taper MT-5 Spindle Motor HP (Peak) 5 HP Spindle Speed (RPM) 4,000 Speed Ranges ONE Speed Selection ELECTRONIC Positioning Accuracy " Position Repeatability " Rapid Traverse (X,Z) 500 IPM Servo Type AC BRUSHLESS Axis Thrust (Peak) 2,000 LBS Air Requirements PSI Coolant Capacity 10 GALLONS Coolant Flow 2 GPM Power Requirements 40 AMPS Voltage Requirements 220 VAC (440 OPT) Shipping Dimensions( WxDxH) 55" x 52" x 71 Operating Dimensions (WxDxH) 55" x 52" x 71" Machine Weight 1,650 LBS SIEMENS 828 CONTROL MACHINE FEATURES 8 station automatic turret 4,000 RPM spindle C3 grade accuracy double nut ball screws Full enclosure with door safety switch High output LED work lamp PLC way lube pump virtually eliminates tramp oil from coolant All axes laser calibrated & ballbar verified Test part cut and shipped with each machine Hand built precision +/ entire travel One year warranty CONTROL FEATURES - SIEMENS 828 CNC 10" high resolution color monitor Simple menu programming - no codes of any kind G code editor runs Fanuc or Haas G code Concurrent verify makes programming faster and easier Solid model part verification shows entire part being cut Handwheel run feature makes proving out programs safer Simple tool management - increases productivity 3 MB part program storage USB port for easy file transfers Siemens High Speed all digital control system - Ultra reliable Siemens Absolute encoders - no homing required Siemens Digital motors, drives and cables Automatic part & tool probe cycles 99 work offsets and 99 tool offsets Coordinate, rotation and scaling User defined macros with 500 variables

4 MACHINE OPTIONS CL SERIES SIEMENS 828 CONTROL OPT-2107 FLOOD COOLANT SYSTEM (Includes high volume pump and adjustable nozzles.) OPT-2121 GRAPHITE MACHINING PACKAGE This package includes one piece sealed way covers and sealed electrical cabinet with heat exchanger. OPT-9233 ELECTRICAL CABINET AIR CONDITIONER Replaces standard fan vented cabinet with a sealed cabinet. Air conditioning unit keeps inside temperature at the desired set temperature regardless of what the outside temperature is. Recommended for area where ambient temperature exceeds 100 degrees Fahrenheit. TOOLPOSTS & TURRETS OPT-3449 BORING BLOCK FOR 5/8" TURRET (1" hole) OPT-3464 FACING BLOCK FOR 5/8" TURRET TOOLING PACKAGES OPT-3329 LATHE TOOLING PACKAGE (5/8 ) (1) 80 Diamond Holder, (10) Inserts, (1) 55 Diamond Holder, (10) Inserts, (1) 35 Diamond Holder, (10) Inserts, (1) OD Threading Holder, (10) Threading Inserts, (1) ID Threading Holder, (10) Threading Inserts, (1) Trigon Tool Holder, (10) Inserts, (1) Boring Bar, (10) Inserts, (1) Boring Bar, (10) Inserts, (1) Cut off Tool, (1) Cut Off Tool Block, (2) Cut Off Blade, (10) inserts Straight, (10) inserts Radius, (10) Inserts, (1) Insert Extractor (Boring bar adapter sleeves not included.) MANUAL CHUCKS OPT-3663 DIRECT MOUNT 6" MANUAL 3 JAW CHUCK OPT-3226 ADJUST TRU 6" MANUAL 3 JAW CHUCK COLLET CHUCKS OPT C PNEUMATIC COLLET CHUCK CL-12, ET-18 ( CAPACITY) CONTROL OPTIONS - SIEMENS 828 OPT-0602 REMOTE ELECTRONIC HANDWHEEL Handy jog handwheel is located in a portable box. Features axis selector switch and a resolution selector for coarse or fine movement. Remote stop start is also included. Also features an innovative function which allows you to control the movement (forwards or backwards) and feedrate of running a part program (Handwheel Run). OPT-2146 HANDWHEEL RUN FUNCTION This feature allows you to control your program execution with the handwheel. Turning the handwheel causes the program to run with you controlling the feedrate. You can move forwards and even backwards with this handy feature. Designed to make proving-out programs easier with safety and confidence. OPT-2147 OPT-2148 DXF FILE IMPORT FEATURE allows you to import DXF files and quickly convert to a conversational program. PROGRAM RUN VERIFY FEATURE allows you to see the tool path and machine position graphically in real time. Displays tool path and solid model. OPT-2163 RESIDUAL MATERIAL DETECTION This software option allows re-machining of pocket milling contours with a tool smaller than the original tool. The control will remember where material has already been machined and will cut only residual material. OPT-9104 HIGH SPEED NETWORK INTERFACE High speed Ethernet port is the ideal way to connect your machine to your LAN (local area network). Features 10/100 MB/s bandwidth for fast uploads and downloads of part programs. Also features a spooling option that allows you to run part programs larger then the memory of the machine. Available in a wireless package for $ extra. OPT-9200 SPARE M FUNCTION (use to connect remote devices like indexers, shuttles, clamps, etc.) OPT-2100 SIEMENS OFFLINE PROGRAMMING SOFTWARE Easy-to-use software package that installs on a standard desktop PC and duplicates the control functions. Allows full programming and part program verification. Single package for lathe and mill. Windows 7 compatible. OPT-2152 EXPANDED MEMORY - 2 GB Standard memory of 3 MB is increased to 2 GB for handling larger CAM programs OPT-2144 SIEMENS TOUCH 2200 CNC CONTROL UPGRADE The 2200 CNC is based on the powerful Siemens 840D platform. This control features a 15" touch screen display, 5 axis expandable and advanced operator functions. Includes Handwheel run and Run verify features as well as probe cycles.

5 CONTROL OPTIONS - FANUC 0i MATE OPT-0202 FANUC 0i MATE STD USB PORT FOR MEMORY STICK DEVICES OPT-0214 HIGH SPEED ETHERNET NETWORK PORT (100 MB/SEC) OPT-0212 REMOTE ELECTRONIC HANDWHEEL WITH AXIS AND RESOLUTION SELECT OPT-0218 OPT-0222 OPT MB PROGRAM STORAGE MEMORY UPGRADE (512K STANDARD) WORK OFFSETS 48 PAIR STANDARD VAC 3 PHASE POWER PROBES OPT-3507 MARPOSS AUTOMATIC TOOL PRE-SETTER Motorized arm type pre-setter swings into position for automatically setting length and diameter offsets. OTHER AVAILABLE OPTIONS OPT-9204 END OF CYCLE LIGHT OPT-3304 BARFEED SYSTEMS MULTIPLE SIZES AND CAPACITIES OPT-3307 BAR PULLER (works with automatic chucks to pull short bars out like a barfeed) FACTORY SERVICES OPT-9000 FACTORY SET-UP & TRAINING AT YOUR FACILITY (3 Days Contiguous US. Includes travel expenses) OPT-9998 TRAINING ONLY -- 1 DAY ELECTRICAL OPTIONS OPT VAC 3 PHASE POWER (220 VAC standard) OPT-2007 CHANGE TO 220 VAC SINGLE PHASE (Uses digital phase converter)

6 GENERAL INFORMAT PERFORMANCE ATC SPINDLE MACHINE CAPACITY MINIMUM SPECIFICATIONS FRYER CM 15 CNC MACHINING CENTER CM-15 X Travel 15" Y Travel 10" Z Travel 15" Ballscrew Size.630" Table Load (Evenly Distributed) 350 lbs. Table Size 10" x 32" T-Slots (No./Width) 4 /.630" Table Top to Floor 32" Motor (Peak) 7.5 HP Spindle Speed (RPM) 60-8,000 RPM Spindle Torque RPM Tool Type/Taper CAT 40 (BT Option) Spindle Nose to Table (Max-Min) 4" - 19" Spindle Center to Column 11" Tool Storage Capacity 8 Station Tool Change Time 5 seconds Max. Tool Diameter(full) 3.5" Max. Tool Weight 10.4 lbs. Max. Tool Length 8" Positioning Accuracy +/ " Position Repeatability +/ " Resolution " Rapid Traverse 500 IPM Cutting Feed Rate IPM Servo Type AC Digital Brushless Axis Thrust (Peak) 2,200 lbs. X, Y, Z Air Pressure Requirements 90 PSI - 3 CFM Coolant Capacity 10 Gallons Coolant Flow 2 GPM Door Open Width 23" Power Requirements 40 AMP VAC 3 Phase ( VAC optional) Shipping Dimensions* (WxDxH) 55" x 52" x 71 Operating Dimensions (WxDxH) 55" x 52" x 80" Machine Weight 2,350 LBS MACHINE FEATURES 8 or 10 tool automatic tool changer Full enclosure with door safety switch 7.5 HP, 40 taper 8,000 RPM spindle Rugged cast iron construction High torque axis motors with 500 IPM rapids 4 nozzle built-in coolant ring High output LED work lamp PLC way lube pump virtually eliminates tramp oil from coolant Power failure protection All axes laser calibrated & ballbar verified Hand built precision +/ entire travel One year warranty CONTROL FEATURES - SIEMENS 828 CONTROL 10" high resolution color monitor Simple menu programming - no codes of any kind G code editor runs Fanuc or Haas G code Concurrent verify makes programming faster and easier Solid model part verification shows entire part being cut Handwheel run feature makes proving out programs safer Simple tool management - increases productivity 3 MB part program storage USB port for easy file transfers Siemens High Speed all digital control system - Ultra reliable Siemens Absolute encoders - no homing required Siemens Digital motors, drives and cables Automatic part & tool probe cycles 99 work offsets and 99 tool offsets Coordinate, rotation and scaling User defined macros with 500 variables

7 EQUIPPED WITH: MACHINE OPTIONS OPT-0320 OPT-2109 OPT-2112 OPT-2114 OPT-9233 MACHINE AND CONTROL OPTIONS Siemens 828 Control RIGID TAPPING FLOOD COOLANT SYSTEM - MB SPRAY MIST COOLANT SYSTEM AIR BLAST SYSTEM Programmable air nozzle for plastic, graphite and other dry materials ELECTRICAL CABINET AIR CONDITIONER Replaces standard fan vented cabinet with a sealed cabinet. Air conditioning unit keeps inside temperature at the desired set temperature regardless of what the outside temperature is. Recommended for area where ambient temperature exceeds 100 degrees Fahrenheit. OPT-2121 GRAPHITE MACHINING PACKAGE (Up TO 60" Travel) This package includes one piece sealed way covers and a sealed electrical cabinet with an high efficiency heat exchanger. 40 TAPER SPINDLE OPTIONS OPT-2200 OPT ,000 RPM 40 TAPER SPINDLE (includes refrigeration unit and air purge seal) BT-40 SPINDLE (for Japanese style BT-40 tooling) ROTARY TABLE CONTROLLERS OPT TH AXIS DRIVE AND WIRING for 6" to 10" Rotary Tables Add this option to any Fryer machine in order to control the 4th axis rotary tables as a full contouring 4th axis. Includes drive, wiring and 4th axis software. OPT TH AXIS DRIVE AND WIRING for 6" to 12" Trunnion Tables Add this option to any Fryer machine in order to control the two axis rotary tables as a 4+1 posistioning. Includes drives, wiring and special 4+1 axis software. (requires 4th axis Drive and Wiring) 4th AXIS ROTARY TABLES Fryer made rotary tables feature exceptional quality and accuracy. Dual worm gear drive, high torque disc brake, AC brushless motor, coolant tight motor Requires rotary table controller above OPT TH AXIS ROTARY TABLE OPT " TAILSTOCK OPT " ROTARY TABLE CHUCK OPT TH AXIS ROTARY TABLE OPT " TAILSTOCK OPT " ROTARY TABLE CHUCK 5th AXIS TRUNNION ROTARY TABLES Fryer made 5th axis rotary tables are perfect for multisided machining and feature 4+1 operation. contour with 4 axis and index with 5th axis. Ultra precise Requires 4th & 5th axis rotary table controllers above OPT TH AXIS TRUNNION ROTARY TABLE CONTROL OPTIONS - SIEMENS 828 OPT-0602 OPT-2146 OPT-2147 OPT-2148 REMOTE ELECTRONIC HANDWHEEL Handy jog handwheel is located in a portable box. Features axis selector switch and a resolution selector for coarse or fine movement. Remote stop start is also included. Also features an innovative function which allows you to control the movement (forwards or backwards) and feedrate of running a part program (Handwheel Run). HANDWHEEL RUN FUNCTION This feature allows you to control your program execution with the handwheel. Turning the handwheel causes the program to run with you controlling the feedrate. You can move forwards and even backwards with this handy feature. Designed to make proving-out programs easier with safety and confidence. DXF FILE IMPORT FEATURE allows you to import DXF files and quickly convert to a conversational program. PROGRAM RUN VERIFY FEATURE allows you to see the tool path and machine position graphically in real time. Displays tool path and solid model.

8 OPT-2163 OPT-9104 OPT-9200 OPT-2100 OPT-2152 OPT-2142 OPT-2154 OPT-2144 RESIDUAL MATERIAL DETECTION This software option allows re-machining of pocket milling contours with a tool smaller than the original tool. The control will remember where material has already been machined and will cut only residual material. HIGH SPEED NETWORK INTERFACE High speed Ethernet port is the ideal way to connect your machine to your LAN (local area network). Features 10/100 MB/s bandwidth for fast uploads and downloads of part programs. Also features a spooling option that allows you to run part programs larger then the memory of the machine. Available in a wireless package for $ extra. SPARE M FUNCTION (use to connect remote devices like indexers, shuttles, clamps, etc.) SIEMENS OFFLINE PROGRAMMING SOFTWARE Easy-to-use software package that installs on a standard desktop PC and duplicates the control functions. Allows full programming and part program verification. Single package for lathe and mill. Windows 7 compatible. EXPANDED MEMORY - 2 GB Standard memory of 3 MB is increased to 2 GB for handling larger CAM programs 3D HIGH SPEED MACHINING Features high speed 1.5ms block processing and 500 block look-ahead. Advance Surface features jerk control and nano smoothing with a compressor mode which determines optimal velocity for programs containing circular and linear blocks. High speed roughing parameters and lower speed finishing parameters provide incredible surface finish at lowest possible cutting time. 4TH AXIS SURFACE CYCLES Allows programming of XYZ coordinates and cycles like pockets and engraving. These are then automatically projected onto a cylindrical surface. For use with 4th axis rotary tables. SIEMENS TOUCH 2200 CNC CONTROL UPGRADE The 2200 CNC is based on the powerful Siemens 840D platform. This control features a 15" touch screen display, 5 axis expandable and advanced operator functions. Includes Handwheel run and Run verify features as well as probe cycles. CONTROL OPTIONS - FANUC OPT-0202 FANUC 0i MATE OPT-0214 HIGH SPEED ETHERNET NETWORK PORT (100 MB/SEC) STD USB PORT FOR MEMORY STICK DEVICES OPT-0212 REMOTE ELECTRONIC HANDWHEEL WITH AXIS AND RESOLUTION SELECT OPT-0213 HIGH SPEED MACHINING PACKAGE for 0i (Fanuc AiCC nano) This package is designed for die mold applications where the ultimate in performance is desired. Features 2 millisecond block processing speed with 200 block look ahead. Bell shaped ACC/DEC interpolation. Nano smoothing and jerk control included OPT-0222 WORK OFFSETS 48 PAIR STANDARD OPT VAC 3 PHASE POWER PROBES OPT-4230 OPT-9222 OPT-2128 FRYER AUTOMATIC TOOL AND PART PROBE PACKAGE This package includes table mounted tool probe to auto set the tool length offset and a wired part probe to auto set pocket centers, bosses, and find edges. The simple graphical interface included gives the operator the fastest set-up possible. MARPOSS WIRELESS TOOL AND WIRELESS PART PROBE PACKAGE Package includes a wireless (IR) table mounted tool probe that automatically measures and sets your tool length and diameter offsets. Also included is an easy to use wireless part probe that works with the ATC and allows you to quickly find edges, hole centers, bosses and many more shapes. Simple graphical menus make operations fast. RENISHAW WIRELESS TOOL AND PART PROBE PACKAGE Special package includes a wireless table mounted tool probe that automatically measures and sets your tool length and diameter offsets. Also included is an easy to use wireless part probe that works with the ATC and allows you to quickly find edges, hole centers, bosses and many more shapes. Simple graphical menus make operations fast. System can also be used to measure part geometry. TOOLING & WORKHOLDING OPT-4214 SANDVIK #40 V-FLANGE TOOLING PACKAGE Standard tooling package includes: (6) collet chucks with the following collet sizes; (1) 1/4 ; (2) 3/8 ; (2) 1/2 ; (1) 5/8 ; (1) 3/4 ; (1) 1. Solid end mill holders as follows: (2) 3/8 ; (2) 1/2 ; (1) 5/ 8 ; (1) 3/ 4 ; (1) 1, (1) 1/2 keyless drill chuck with holder, collet chuck wrench & set-up fixture, (14) retention knobs. OPT-9097 PACKAGE OF 12 CAT-40 OR BT-40 RETENTION KNOBS (specify at time of order) FACTORY SERVICES OPT-9000 OPT-9996 ELECTRICAL OPT-3308 OPT-2007 FACTORY SET-UP & TRAINING AT YOUR FACILITY (3 Days Contiguous US. Includes travel expenses) TRAINING ONLY -- 1 DAY 440 VAC 3 PHASE POWER (220 VAC standard) CHANGE TO 220 VAC SINGLE PHASE (Uses digital phase converter)