Boat Hull Solid. (Alt-2). in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1
|
|
- Julianna Bernice Heath
- 5 years ago
- Views:
Transcription
1 Mastercam X7 Chapter 29 A. Open Boat Block File. Step 1. Open your BOAT BLOCK file. Boat Hull Solid B. Save As BOAT HULL SOLID Step 1. Click File Menu > Save As. Step 2. Key-in BOAT HULL SOLID for the filename and press EN- TER. C. Set Grid and Snap.1. Step 1. Use Alt-G to display Grid dialog box, Fig. 1 Check Active grid Check Visible grid Set X and Y Spacing.1 and click OK. D. Create Back Rib. Step 1. Set color back to cyan or your default color. Click color swatch in Status Bar at bottom of screen. Key-in 11 for cyan color number and press ENTER. Fig. 1 Step 2. Change to Front View (Alt-2). Step 4. Change depth of your drawing. Click in Z field screen, key-in -9 and press ENTER. Step 5. Click Create Menu > Line > Endpoint or Line Tool in toolbar. Step 6. Draw lines in Fig. 2. Step 7. Click Apply in ribbon bar to fix entity. E. Create Rib 2. Step 1. Change depth of your drawing. Click in Z field screen, key-in -4.9 and press ENTER. 6 in Status bar at bottom of 7 4 Z Depth -9 Fig. 2 in Status bar at bottom of Step 2. Draw lines in Fig. 3. When you draw line to centerline do not snap to centerline or line that was drawn at Z depth -9. Step 3. Click OK bar. in ribbon bar to fix and close ribbon Fig. 3 Mastercam X7 BOAT HULL SOLID Page 29-1 Cudacountry.net Tech Ed cudacountry@hotmail.com 9 3 Z Depth -4.9 Do not allow center line or line at Z -9 to highlight
2 F. Turn Off Grid and Snap. Step 2. Change to Isometric View drawn at both depths, Fig. 6. (Alt-7). Confirm lines are Step 1. Use Alt-G to display Grid dialog box, Fig. 4 Uncheck Active grid Uncheck Visible grid Click OK. G. Mirror Lines. Step 1. Click down arrow of Set Planes in toolbar and click Front (WCS), Fig 5. Step 2. Click Xform Menu > Mirror. Step 3. Select the 4 rib lines and click End Selection (ENTER) in ribbon bar, Fig. 6. Step 4. In Mirror dialog box: Select Copy, Fig. 7 Click Select line Click vertical line in rear, Fig. 7 Click OK to close Mirror dialog box. Fig. 5 Mirror line Fig. 6 Fig. 4 Fig. 7 Step 5. Right click drawing area and click Clear Colors (Alt-R C). Step 6. Save H. Turn Off Block Level. Step 1. Display Level Manager. Use Alt-Z. Step 2. Uncheck BLOCK level to hide Level and click OK, Fig. 8. Fig. 8 Mastercam X7 BOAT HULL SOLID Page 29-2
3 I. Draw Hull Splines. Step 1. Click Create Menu > Spline > Manual Spline. Step 2. Draw a spline across the ends of ribs and Point, Fig. 9. Start with the Point 1, middle rib 2 and finish with rear rib 3. Be sure to snap to endpoint of rib lines Click Apply in ribbon bar apply spline. 1 Step 3. Repeat and draw another spline across at 1, 4 and 5. Click Apply in ribbon bar apply spline. 2 Spline 1 4 Fig. 9 3 Spline 2 Spline 3 5 Step 4. Also draw spline across at rear rib 3 and 5. Click OK close ribbon bar. in ribbon bar to fix spline and Step 5. Save J. Add Surfaces Level. Step 1. Display Level Manager (Alt-Z). Step 2. Key-in 3 in the Number field. Step 3. Press Tab key to move to the Name Field and keyin SURFACES and click OK, Fig. 10. Fig. 10 Mastercam X7 BOAT HULL SOLID Page 29-3
4 K. Create Flat Boundary Surfaces. Step 1. Draw surfaces yellow. Click the color swatch in Status Bar at bottom of screen. Key-in 17 for yellow color number and press ENTER (Alt-R T key-in 17 Alt-O). Step 2. Click Create Menu > Surface > Flat Boundary. Chain Step 3. Select Chain box, Fig. 11. in Chaining dialog Step 4. Click a spline to define flat boundary 1, Fig. 12. Step 5. Click End Chain Chaining dialog box, Fig. 11. in Fig. 12 Chain Step 6. Click line of rear rib to define flat boundary 2, Fig. 13. Fig. 11 Step 7. Click OK in Chaining dialog box, Fig. 11. Fig. 13 Step 8. Click Yes to Automatically close chain. Step 9. Click OK in ribbon bar to fix surface and close ribbon bar. Fig. 14 Step 10. If necessary, turn on shading (Alt-S), Fig. 14. Mastercam X7 BOAT HULL SOLID Page 29-4
5 L. Create Loft Surfaces. Step 1. Click Create Menu > Surface > Ruled/Lofted. Step 2. Click Single in Chaining dialog box, Fig. 15. Step 3. Chain entities in order, rear Line and middle Line. Select Lines at the same end. Here Lines were selected at the bottom end, Fig. 16. If when chaining the Lines chaining directions arrows do not pointing in the same direction - click Reverse in the Chaining dialog box. Step 4. Click Point in Chaining dialog box, Fig. 17. Fig. 16 Step 5. Click the Point, Fig. 16. Fig. 15 Step 6. Click OK box. in Chain dialog Step 7. Click Apply in ribbon bar to apply surface. Fig. 18 Step 8. Repeat at the next set of ribs. and selects and select in Chain in rib- That is, click Single lines. Click Point Point. Click OK dialog and Apply bon bar, Fig. 19. Fig. 19 Step 9. Repeat for the next 2 set of ribs, Fig. 20 and Fig. 21. Fig. 17 Step 10. Click OK in ribbon bar. Step 11. Save Fig. 20 Fig. 21 Mastercam X7 BOAT HULL SOLID Page 29-5
6 M. Add Solids Level. Step 1. Display Level Manager (Alt-Z). Step 2. Key-in 4 in Number field, Fig. 22. Step 3. Press Tab key to move to Name Field and key-in SOLIDS and click OK. Step 4. Click to uncheck GEOMETRY level and click OK. Step 5. Save N. Surfaces Into Solid. Step 1. Click Solids Menu > From Surfaces. Fig. 22 Step 2. Check Keep and click OK, Fig. 23. O. Turn Off Surfaces Level. Step 1. Display Level Manager (Alt-Z). Step 2. Click to remove X in Visible column of SURFACES level and click OK, Fig. 24. Confirm there is only 1 entity in the HULL SOLID level. Step 3. Save Fig. 23 Fig. 24 Mastercam X7 BOAT HULL SOLID Page 29-6
7 P. Shell Solid. Step 1. Use Dynamic View Fig. 25. to flip the hull over to view the top, Step 2. Fit (Alt-F1). Step 3. Click Solids Menu > Shell. Fig. 25 Step 4. Click the top face of the hull, Fig. 26. Step 5. Click End Selection (ENTER) in ribbon bar, Fig. 7. Top Face Step 6. In the Shell Solid dialog box, Select Inward Fig. 27 Shell Thickness.05 Click OK. Fig. 26 Step 7. Save Fig. 27 Mastercam X7 BOAT HULL SOLID Page 29-7
Step 3. Rectangle. Fig. 1. Step 6. For the Placement Point, click the bottom left gray rectangle and click OK, Fig. 2. to fit the drawing on screen.
Chapter 24 BOAT SOLID A. Name Level. Hold down ALT and press Z. Step 2. Key-in block for Name and click OK, Fig. 1. B. Create Rectangle. Step 3. Rectangle. Fig. 1 Step 4. 1 Point. Step 5. Key-in 9 for
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click File Menu > New.
Mastercam X7 Chapter 26 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click File Menu > New. Step 2. Click Create Menu > Rectangle or click Rectangle Tool Step 3. In the
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationCatamaran A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N).
Mastercam 07 Chapter 6 Catamaran A. Create Rectangle. Step. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step. On the Wireframe tab click Rectangle. Step
More informationCudacountry Radial. Fig. 2. Point. Fig. 4. Mastercam 2017 Cudacountry Radial Page 19-1
Mastercam 2017 Chapter 19 Cudacountry Radial A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New QAT. (Ctrl-N) on the Quick Access Toolbar Step 2. On the Wireframe tab click
More informationToolpaths for Fuselage
Mastercam Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Machine Type and Stock Setup. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. If necessary, display
More informationCHANNEL BLOCK SOLID. Step 7. For the Placement Point, click the bottom left gray rectangle and click OK. to fit drawing on the screen.
Chapter 9 CHANNEL BLOCK SOLID A. Create Rectangle. Step 1. Change to the Front View. Use green Front View or ALT-6 F. Hold down ALT and press 6. Key-in F. Step 3. Create. Step 4. Rectangle. Step 5. 1 Point.
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationChapter 36. Mastercam Jewelry Box Fixture. A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 36 Jewelry Box Fixture A. Sketch Fixture Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationPanel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
More informationMastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationPenny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam Step 1. If necessary, save your BASE file in SOLIDWORKS.
Mastercam 2017 Chapter 22 Chapter 7 Penny Hockey SOLIDWORKS 17 to Mastercam 2017 A. Open File in Mastercam 2017. Step 1. If necessary, save your BASE file in SOLIDWORKS. Step 2. In Mastercam 2017, click
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationFig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationToolpaths for Fuselage
Mastercam 2017 Chapter 18 Chapter 22 23 Airplane Toolpaths for Fuselage Finish Blend A. Hide Top Surface. Step 1. If necessary, open your FUSELAGE file from Chapter 17. Step 2. On the Home tab click Hide/Unhide
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationDelta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
More informationF-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationTRAINING GUIDE WCS-PART-1
TRAINING GUIDE WCS-PART-1 Mastercam Training Guide Objectives The learner will create the geometry for WCS-Part-1. This Lesson will cover the following topics: Create a 3-dimensional drawing by: Creating
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationBlank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationTRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationTRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationTRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationTRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-1 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives Previously in Mill-Lesson-6 and Mill-Lesson-7 geometry was created and machined using standard Mastercam methods.
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationDrawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationAirplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationModule 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
More informationTRAINING GUIDE WCS - VIEW MANAGER - PART-2
TRAINING GUIDE WCS - VIEW MANAGER - PART-2 Mastercam Training Guide Objectives The learner will create the geometry and toolpaths for WCS-Part-2. This Lesson will cover the following topics: Create a 3-dimensional
More informationBottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More informationBrief Introduction to MasterCAM X4
Brief Introduction to MasterCAM X4 Fall 2013 Meung J Kim, Ph.D., Professor Department of Mechanical Engineering College of Engineering and Engineering Technology Northern Illinois University DeKalb, IL
More informationToolpaths for Boat. OptiRough and Finish Waterline. Step 8. Click OK in the Machine Group Properties, Fig. 2. Stock display Click corner to move arrow
Mastercam 2017 Chapter 33 Toolpaths for Boat A. Machine Type and Stock Setup. Step 1. If necessary, open your BOAT ROUND BOTTOM. Step 2. If necessary, display Toolpaths Manager. On the View tab click (Alt-O).
More informationPropeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationSOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
More informationGrapher 10 Ribbon Bar
Grapher 10 Ribbon Bar When Grapher 10 was released, it included many changes to the user interface. Once such change was the new Ribbon Bar. The Ribbon Bar is designed to better emulate the menu bars in
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationSOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users
SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing
More informationTRAINING GUIDE SOLIDS-LESSON-3
TRAINING GUIDE SOLIDS-LESSON-3 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationCreate the Through Curves surface
Create the Through Curves surface 1. Open ffm4_mc_fender. 2. Select all three strings, and then on the Analyze Shape toolbar, click Show End Points. Notice there are two curves in the strings on the left
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationTRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL
TRAINING GUIDE MILL-LESSON-FBM-2 FBM MILL AND FBM DRILL Mastercam Training Guide Objectives This lesson will use the same Feature Based Machining (FBM) methods used in Mill-Lesson- FBM-1, how ever this
More informationExport DXF to Illustrator
Chapter 12 Glider Export DXF to Illustrator A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More informationDrawing. Chapter 11. Bridge. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. on the View Layout toolbar.
Chapter 11 Bridge Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationSolidworks 2006 Surface-modeling
Solidworks 2006 Surface-modeling (Tutorial 2-Mouse) Surface-modeling Solid-modeling A- 1 Assembly Design Design with a Master Model Surface-modeling Tutorial 2A Import 2D outline drawing into Solidworks2006
More informationLAB # 2 3D Modeling, Properties Commands & Attributes
COMSATS Institute of Information Technology Electrical Engineering Department (Islamabad Campus) LAB # 2 3D Modeling, Properties Commands & Attributes Designed by Syed Muzahir Abbas 1 1. Overview of the
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationSolidWorks 2013 and Engineering Graphics
SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following
More informationFlow Sim. Chapter 16. Airplane. A. Add-In. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 A. Add-In. Step 1. If necessary, open your ASSEMBLY file. Airplane Flow Sim Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More informationTOOLPATHS TRAINING GUIDE. Sample. Distribution. not for MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR
TOOLPATHS TRAINING GUIDE MILL-LESSON-4-TOOLPATHS DRILL AND CONTOUR Mill-Lesson-4 Objectives You will generate a toolpath to machine the part on a CNC vertical milling machine. This lesson covers the following
More information3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.
3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats
More informationAn Introduction to Autodesk Revit Massing, Surface Divisions, and Adaptive Components
An Introduction to Autodesk Revit Massing, Surface Divisions, and Adaptive Components Chad Smith KarelCAD, Australia AB2463-L As the Revit massing tools become more polished and robust, users are becoming
More informationSOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationExport DXF to CorelDRAW
Chapter 13 Glider Export DXF to CorelDRAW A. Export Fuselage/Tooth Sketch as DXF". Step 1. Open your FUSELAGE part file. Step 2. Roll the rollback bar to below the Cut-Extrude1. To rollback, click Fillet1
More information1st Point. 2nd Point. hold shift & drag along Y. Splines
Splines STEP 1: open 3DS Max _ from the Command Panel under the Create tab click on Shapes (note: shapes are really Splines) _ under Object Type click on Ellipse STEP 2: Expand the Keyboard Entry tab type
More informationTRAINING SESSION Q2 2016
There are 8 main topics in this training session which focus on the Sketch tools in IRONCAD. Content Sketch... 2 3D Scene Background Settings... 3 Creating a new empty Sketch... 4 Foam with cut out for
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationBasic Modeling 1 Tekla Structures 12.0 Basic Training September 19, 2006
Tekla Structures 12.0 Basic Training September 19, 2006 Copyright 2006 Tekla Corporation Contents Contents 3 1 5 1.1 Start Tekla Structures 6 1.2 Create a New Model BasicModel1 7 1.3 Create Grids 10 1.4
More informationMASTERCAM WIRE TUTORIAL. June 2018
MASTERCAM WIRE TUTORIAL June 2018 MASTERCAM WIRE TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject to the Mastercam End
More informationME Week 3 Project 3 - Plastic Part Thicken Method
Plastic Part Commands The following section will give a further overview of the Autodesk Inventor plastic part commands. 1. Project 3 This project will further introduce you to the Autodesk Inventor 2012
More information