Flashloader 200 (V3.34 or higher)

Transcription

1 Version August 2014 AgGPS 252 receiver NH 252 receiver AFS252 receiver AgGPS 262 receiver NH 262 receiver AFS262 receiver AgGPS 372 receiver NH 372 receiver AFS 372 receiver AgGPS 162 receiver NH 162 receiver AFS162 receiver version bf_370.img (don t use PF software 28.8 otherwise the RTK config (channel ID) will be lost) AgGPS262_5_02_002_4.img - required to be compatible with configuration changes in PF V28.8 and NAV V3.95. For 262 the configuration change is mainly related to configuring the RTK Channel ID. wahoo_3_15_004_4.img (Ag372) - required to be compatible with configuration changes in PF V28.8 and NAV V Added ability to change the frequency of AG- 715 or AgGPS 450/900 radios without the Nav Controller II present -Improved long convergence times experienced with RTX in rare cases. - RTK Age is <60 seconds if xfill Sat is not visible -Improve RTX bridging function, when less than 4 satellites were visible during bridging periods. ahi_1_01_000_4_162.img The version below is available but only corrects a small bug: ahi_2_17_004_4.img Download Flashloader 200 (V3.34 or higher) EST availability (V ) (To be able to use the 162 receiver for autoguidance (Egnos), you will need to unlock the 162) GPS Remote software or by screen of your application (EZ-guide plus, EZ-guide 500, SWCD,CODI,FRED) Configure AORE(120) or IORW(126) to heed health and all the rest to disabled For OmniStar configure the receiver to ESAT. On some receivers it may be necessary to configure the satellite frequency manually ( MHz/Baud Rate: 1200bps) (Europe Only). For RTX CentrePoint (Sat) and Rangepoint configure the receiver to MHz and baud rate 600bps. For RTK unlocked receiver, this configuration should be done in RTK Config menu & NOT the DGPS Config menu in the RDI screen (Europe Only). Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS or / /ZTN50166 is the big one (7 meter) Or alternatively: ZTN68463 (data output cable 262/162)

2 EZ-guide 500 screen EZ-guide 250 screen FM750 FM1000 XCN2050 version Ezg500_5_10_038 _4.img Languages: *.lpf ezg250_3_10_038 _4.img Languages: *.lpf cfx750_6_00_048_4.img Languages: *.lpf V autopilot configuration, calibration and diagnose available on the screen. VDB access from a usb stick. - headlands infield control fix V TUVR seed rate limit increased V6.0 Ez-Steer, Ez-Pilot :Reverse recognisation : boom stability - settings available for Hardi 6500 First install monitor v "cfx750_mon_1_17.mnc" if FM750 is <V1.90 V8.2_FM-1000_Integrated_Display_Firmware.upg V Support for xfill & RTX RangePoint V The DCM-300 modem now notifies users when modem firmware updates are in progress. - A VRS Disconnected warning no longer appears when running xfill technology. V new Isobus platform supported - water management enhancement V OnSwath advanced guidance line acquisition - revised Vehicle types for EZ-Pilot and EZ-Steer - turkish language support (see the release notes on the Trimble Support Page for more detail on new features and improvements) V1.6_TMX-2050_ V Ez Steer Ez Pilot Autopilot Field IQ DCM300 All signals V more Field IQ platforms supported - more languages supported - increased data management V Expanded SIM selection options - improvement of the translations - increased data management V prescription feature -NMEA output via Nav Controller - new version for TM200 (v2.0) Download Copy to USB (for XCN warranty activation should be completed otherwise the software will not be recognised) EST availability Password: 2009 Firmware version: EST + ASIST>>>Trimble Support Page Firmware version & Language Files (FM750): ASIST>>>Trimble Support Page USB Device: Lexar firefly 1GB (P/N ZTN )

3 062/Garmin antenna NH/AFS 100/110/134 EZ-guide plus screen Field Manager display version No Available NH/AFS100 : CF_306.tnr NH/AFS110 : SS_306.tnr NH/AFS134 : BT_306.tnr EZGPlus EU6.ROM v5.20 (Upgrade, autorun, cougar) Download [No Available] Flashloader 100 EZ-box software Copy to Compact Flash Card ( Copy the upgrade folder and autorun/cougar-files) SNSRCFG_320.exe - Ensure baud rate is configured to 38400bps - NMEA 2.30 mode is set to ON - FIX + DGPS + DIFF mode is set to AUTO - Only NMEA sentences GPGGA, GPGSA, GPVTG, GPGSV should be selected for good communication with the display GPSRemote software or by screen of your application (EZ-guide plus, EZ-guide 500, SWCD,CODI) Configure AORE(120) or IORW(126) to heed health and all the rest to disabled Password: 2005 Firmware version : No EST availability Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS EZ guide plus lightbar guidance system Firmware version: ASIST>>>Trimble Support Page AND A1 OR Null modem cable ZTN59043 OR (in kit) CF Card+adapter: P/N :

4 Intellisteer/Accuguide Trimble autopilot EZ-steer EZ-steer 500 EZ500 EZ250 FM750 FM1000 EZ-Pilot version Display AutoGuidance SW CNH NAV SW V V (New steering Cal logic for CCH) V V (sudden XTE jump fix) V V28.4 (lang28.5) 3.85 (AG715 RTK Radio Channel Fix) V AG 28.9, PF V28.8, NAV V3.95, 372 V3.15, 262 V5.02 must be all updated together to ensure compatibility Receiver/Display SW EZ-Guide Plus EZ500 (V3-3.06) EZ500 (V5.10) FM1000 (V4.00) FM750 (<V1.90) 262 (V2.00) 252 (V3.70) FM1000 (V8.02) FM750 (V6.00) Trimble NAV SW v.4.52 V5.15/V5.16 V6.00 VDB6.0 SCM_3_0_1.app SCM_4_1_0.app No Available Download Fixed problems : - RTX Rangepoint - Recorded swath lost after key cycle - ISO Task Controller - AA 005 error - ISO Task Controller - Forward offset value overridden after a power recycle - MultiSwath introduced - TC software version for SWCD 2.0 added FlashLoader 200 When updating the NAV ensure the following process is followed: 1. Load default vehicle with AP box of FM Upgrade the NAVII firmware 3. Choose a profile from VDB list V Recalibrate the system EZ-box software N/A Intellisteer/AccuGuide: For more configurations: use Autopilot box II Trimble Brand Autoguidance systems AP toolbox update V Include gyro diagnostic values (not available on EST V8.0, to be downloaded on Trimble Support Page) EZ500 / EZ+ use EST: Autopilot box Trimble Brand Autoguidance systems FMD + FM FM750 + XCN2050: in display config or AP box EST availability CNH NAV version : Yes (3.78, 3.80, 3.88, 3.90, 3.95) Trimble NAV Firmware version and VDBlist 6.0: ASIST>>>Trimble Support Page EZ guide plus lightbar guidance system Is also possible without cable N/A Serial cable e.g. from EST box To support all ages of IS/AG vehicles it will be necessary to order each of the three cables above. Serial cable e.g. from EST box Note: For CNH Hybrid Installations the cables in the cell to the left will be required for software download to the Trimble Autopilot Controller N/A

5 AgGPS 450 Radio PDL 450 Radio TDL 450 Radio AG-715 Radio AgGPS RTK 450/442/542 Base version Download v1.30 AgGPS450_v130Upgrade.zfimg v1.32 (required for ( MHz) radio: AgGPS450_v132Upgrade.zfimg Flashloader 200 or v2.42 V N/A TDL Conf V3.02 No Download PDL Conf v.4 v3.67 (not for 542 base) V4.60 V4.7 Version 4.7 allows setting of delay of signal transmission EST availability Winflash software (Select Sitenet 450 Transceiver ) (Press Ctrl+Insert to insert new software if not available yet) (for download set-files: use Winflash) Download/Config: Yes Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS Choose generic CMR radio in EZ 500 when used as rover radio for EZ 500 (In EZ 500 for RTK security: choose Trimble radio: configure secure code, and then choose generic CMR radio) Download/Config: Yes Set Files loaded with TDL Conf. s can be done with TDL Conf or using UI on the radio Firmware version : No Download/Config: ASIST>>>Trimble Support Page AgRemote software or by using the RDI screen Note: No set-file is required. Frequencies are configured in the AgRemote/RDI tool. To avoid problem of radion configuration, it s recommended to update the receiver to V3.05 or higher. Download/Config: Yes Winflash (Select Trimble AgGPS Receiver ) (for download set-files: use Winflash) Winflash-tool required to connect to 542-base. For 450 Install: "wamel_v470.timg" For 542 base install: ` gamel_v470.timg. Firmware version : No / Intellisteer Autoguidance System II / Precision Farming / GPS Both tools required: Together with PDL 450 radio (= power cable) Together with TDL 450 radio (= power cable) Nullmodem cable ZTN59043 OR (in kit)

6 EZ-boom Field IQ/Yield Monitoring/Generic Rate Controller DCM-300 Modem AM50 Modem version TR_EZBOOM- 1_5.fw2 Display MSB 1 12 SSB 2 RWCM 3 SIM 4 SCM 5 RSCM 6 SMM 7 MSM 8 YMM 9 XCN V3.05 V3.05 N/A V3.05 V3.05 V3.08 N/A N/A N/A FM1000 >V7.1 V3.05 V3.05 V3.05 V3.05 V3.05 V3.06 V2.05 V1.11 V1.15 FM750 >V1.9 V2.06 V2.06 V2.06 V2.07 V2.07 V2.14 N/A N/A N/A >V4.0 V3.05 V3.05 V3.05 V3.05 V3.05 V3.05 V2.02 V1.11 V1.15 EZ500 V5.10 V1.02 V1.02 V1.02 N/A V1.04 N/A N/A N/A N/A CNH GRC GRC V28.7 V3.06 V3.06 V3.06 V2.08 V3.06 V3.17 V2.06 N/A N/A V6.01 allows selection of 2G/3G V7.0 provide a faster response on the dispaly Install NAV V3.72 and V27.2 (AG+PF) as a minimum when using DCM300 modem with Intellisteer/AccuGuide Telematics_ 28_05_00_00 Ag modem software: V (fyi:ce modem software: V1.2.0 < V50 are for CE >= V50 are for Ag) Download EZ500: EZ Boom - Copy to USB (root). (EZ500 will work with Field IQ (but not recommended). SW update is not possible. Use FM750/FM1000 for SW Update.) FM750 Copy to USB (root) Not compatible with EZ-Boom FM1000 Included in display main firmware - FM1000 v5 or higher NOT compatible with EZ-boom and TAC XCN 2050 Included in display main firmware EZguideplus: EZ-toolbox Not compatible with Field IQ FMD Copy to Flash Card under Firmware folder - Not compatible with Field IQ CNH GRC Use EST Planting & Seeding Equipment>>IntelliRate Control/AFS AccuControl System and Aftermarket ISOBUS Implements : Downloads are over-the-air (OTA) Submit an ASIST report or contact local support with modem serial number and request the update. EST (add the telematics software during the screen update procedure) FMD EZ-Boom Only FM750 Field IQ Only + PLM / AFS Connect Website EST availability (V ) Firmware version: For Trimble Field IQ: ASIST>>>Trimble Support Page For CNH GRC: Ensure EST Update 1 is installed on the EST laptop Trimble WebService Firmware: N/A : Instructions for WebService in EST available on Asist Connect to the modem with WiFi laptop For Trimble FIQ: USB Device (Lexar firefly 1GB (P/N ZTN )) For CNH GRC: EST Dearborn DPA5 P/N Note1: The software filenames below are an example of the filename spelling and is not necessarily the latest/correct version for the controller in all cases. Note2: Filenames for CNH Generic Rate Controller (GRC) will have the file extension.hx1 MSB 1 Master Switch Box FIQ_12_Section_Switch_Module_2_06.ohr 12 SSB 2 12 Section Switch Box FIQ_Master_Switch_Module_2_06.ofr RWCM 3 Rawson Control Module FIQ_Rate_and_Section_Control_Module_2_14.ohk SIM 4 Switch Interface Module FIQ_Rawson_Control_Module_2_06.orn SCM 5 Section Control Module - FIQ_Section_Control_Module_2_07.omg RSCM 6 Rate & Section Control Module - FIQ_Rate_and_Section_Control_Module_2_14.ohk SMM 7 Seed Monitor Module - FIQ_Seed_Monitoring_Module_2_05.okn MSM 8 Moisture Sensor Module - FIQ_Moisture_Sensor_Module_1_11.oms YMM 9 Yield Monitoring Module - FIQ_Yield_Monitoring_Module_1_15.odu