Harton beer line counter BCM-6

Transcription

1 Harton beer line ounter BCM-6 User s manual for 6 independant beer lines Pre-programmed for liter and deiliter ounting Use of any available flowmeter (12 V) Flowmeter inputs by opto-ouplers Calibration of flowmeters by dispensing or programming Automati display of results hanel by hanel (inputs used only) 1 hour autonomy with inluded battery Memorisation of power off / power on events Real time lok Aess to programming by PIN ode Results are proteted by PIN ode Possibility to onnet a printer or a PC Otober

2 aess to menus To enter in the menus, press the 4 keys in the following order + _ Aess to menus by PIN ode : default at delivery Z Reports 003 Cleaning 004 Calibration 005 PIN ode? 0 nter the 3 digits ode with To introdue your own PIN ode : nter in the menu The first PIN ode is displayed + _ and PIN Progr,? 001 Results then Z Reports To quit programming and results mode use Cleaning Calibration To quit alibration and leaning mode use Press Modify value with the first digit is underlined + _ Selet other digits with Then, press Otober

3 Calibration volume 200ml 500ml 1000ml 4fl.oz. 12fl.oz. 32fl.oz. Date Hour Volume? 1000ml Ref. Port.? 0500 Day? 13 Month? 06 Year? 07 #02 Volume?1000ml #02 Ref. Port.? 0500 #02 Hour? 10 Minute? 37 Seond? 25 #06 Volume?1000ml PIN Progr,? 001 #06 Ref. Port.? 0500 PIN X Res,? 002 #06 PIN Z Rep,? 003 PIN odes must be different for eah menu CR : er Hart96 Spirit Generi Change with PIN Clean,? 004 Line feed? 05 For printer PIN Calib? 005 CR? er CR onnetion Delay? 002 Delay for automati display If 000, results are not displayed automatially Otober

4 Z Reports Z Reports Display daily Display periodi Z daily Z periodi L vent journal : Line 1: line number event type Line 2: date - hour Press After Z report, returns to main display # L L #003 Power-Off 28/08/06 15:40 X daily Volume displayed in liter (if alib. volume is in oz, the display will show the volume in oz) X periodi # L vent Journal #001 Power-Off 29/08/06 12:15 Otober

5 Cleaning - Calibration Cleaning Calibration This mode is used when beer lines must be leaned. In this mode, the BCM-6 will not ount the volume dispensed in eah hannel. Press to return in normal dispense mode This mode is used to alibrate eah hannel of the BCM-6 ounter. First hoose the alibration volume desired for eah hannel in the menu - Volume nter the Calibration mode Dispense preisely the alibration volume nb and pulses (Ref. Port.) are displayed during dispensing Repeat this operation for all hannels used (only 1 hannel at a time) alibration mode with Flowmeters are alibrated and the referene portion is now memorised. (If the number of pulses in <5 during alibration, referene portion is not modified) You an adjust this value in the menu Ref. Port. Rem.: if the number of pulse per liter is well known for eah flowmeter, you an introdue this value in Ref. Port. without alibrating (hoose alibration volume 1000ml) Otober

6 Software update To make a software update of the BCM-6 you must have C3Builder or C3asy version 2.43 or later installed in your omputer In ase of new version available or to hange the language in the BCM-6 proeed as follow : Start C3Builder - Bar design Go to menu C3 modules Update of software for modules Go to menu Tools Request loop onfiguration On Module type hoose BCM6 Open Version of the program of the module Selet appropried language Start Update flash memory Otober

7 onnetions BCM-6 rear view Protetive plate to hold ables and onnetors er Power supply 12 VDC RS-232 Flowmeters Power supply do not onnet Tx (out) Rx (in) er or PC Flowmeter Power supply onnetion If power supply is disonneted (mains), the baklight of the display will be swithed off and the harater! will be displayed in reverse video BCM6 by! Swiss Made HARTON S.A. 14b Chemin du Lavasson 1196 Gland - Switzerland Otober