How to Use Model 2. Hardware and Software Training

Transcription

1 How to Use Model 2 Hardware and Software Training

2 You Need Principle Content Digital Model Preparation Print Material Hardware Setting and Software Guides Start to print Expanded Funcionality

3 You Need 1. Computer 2. Model 2. Multiple DIY Printing Material 4. Kitchen Tools according to the Chosen Material 1

4 Wiring 1

5 Basic D Printing Workflow App Command Medium Printer Controls Printing FabStudio Multiple Format Digital Model.stl Files.fab Files Fab Interpreter

6 Printing Principle

7 Printing Material Icing cookie dough Cream Frosting Silicone and Frosting Silicone Chocolate Cheese Material you developed

8 Loading syringes One key to successfully using the is making sure that there are no air bubbles in the syringe. With silicone in containers that use a caulking gun for extrusion, it is best to unscrew the tip from the tube, insert the stub into the bop of the barrel, and rapidly extrude material into the syringe until it reaches the tip. You can slide a wire down alongside the plunger when you use DIY materials. As the plunger is depressed, the air can escape through the gap provided by the wire.

9 Loading syringes Inserting the syringe to the and screw the shafts to the pistons through the gears.

10 Reloading syringes Click Pause Button in FABInterpreter Unscrew the shafts to the pistons through the gears and replace the exhausted syringe with a full one

11 Fix Z-Belt using Hex Wrench

12 Unplug Crystal Head from Snap Motor press 1 2 Rotate slightly Unplug 4

13 Prepare for Printing Many materials will adhere to the build surface, so it is recommended that you cover the build surface with a thin disposable or washable material, such as waxed paper, aluminum foil, plastic wrap, etc. We recommend aluminum foil when you print silicone. Set the position as the following photos. Carefully adjust the z-height until the syringe tip just touches the build surface.

14 Prepare for Printing H=2/ diameter of needle

15 Download: Software Download FabInterpreterV0.exe FabStudio v1.1 win2.. Printer Configs.zip from 2

16 Run Software Run FabStudio and FabInterpreter directly FabInterpreterV0.exe FabStudio v1.1 win2.. Printer Configs.zip 2

17 Digital Model Preparation Adapt object manually or type parameters.stl file address Drag the object to the main window

18 Digital Model Preparation Click and Adapt object manually or type parameters Drag for scaling Drag for moving Drag for rotating Type parameters

19 Digital Model Preparation Click Put on Tray and Arrange Objects after adapting the model

20 Select Object Material 1 Click 1 Materi and drag 2 seleted material to the object (the object turns green) 2 1

21 Select Object Material Click 1 Send to printer! and select 2 Blue Taper silicone Then click Create Printing job. 1 2

22 Select Object Material After calculation click 1 Save to a File 1 Save.fab file to a folder of your choice

23 Select Object Material 2 Click 1 Send to printer! and select 2 Green Taper silicone with Frosting Support (depends on if you have support material). Then click Create Printing job. 1 2 Save.fab file to a folder of your choice

24 Printer Controls Open FAB2.exe. Click Load New Config and double click Duel Syringe Model 2.config from Printer configs folder. 1

25 Boot Printer through PC Connet and your PC as follows

26 Boot Printer through PC Switch the SnapHub into pass thru mode Turn the SnapHub on after ensuring the needed motors are plugged into the hub Plug the machine into your PC, the needed drivers should auto install on Windows. Find which com port the printer is on Change the comport value in the printer config files to be that value

27 Boot Printer through PC Find which com port the printer is on Open Device Manager Under Ports look for the COM Port used by a UART device. COM X

28 Boot Printer through PC Change the comport value in the printer config files to be that value Open the.config file you want to use in FAB interpreter in a text editor and search for <comport>*</comport> to find the configrued port number. Change * to X as you find.

29 Boot Printer through PC Change the comport value in the printer config files to be that value X

30 Printer Controls You can adapt the components positions through Interpreter

31 Printer Controls Click Load to load.fab file and chose material for bay. And then click Execute to start print. You can also click Pause for change syringe when printing.

32 Print with Support Click Load to load.fab file and chose material for bays when you chose support mode. And then click Execute to start print. You can also click Pause for change syringe when printing.

33

34 Convert to a D Router Stick wood or foam on Z table surface Carefully adjust the z-height until the dremel tip just touches the material surface.

35 Convert to a D Router 1 Select Fab@Home Model 2 Dremel and drag 2 seleted material to the object Select Single Syringe Config for FABInterpreter 1 2