CITY OF KENNER COMMENTS CONCOURSE A 100% CONSTRUCTION DOCUMENTS Permit Comments

Transcription

1

2

3 DESIGNER SUPPLEMENTAL INSTRUCTIONS DSI NO. CCAT DSI-0044 CC+T Crescent City Aviation Team LEOADALY / ATKINS A Joint Vent ure DATE 07/07/2017 PROJECT NAME: NOAB Project # Louis Armstrong New Orleans International Airport North Terminal Development Program Phase 1 Note: if the following information is deemed to have an impact on GMP Price or time, submit a proposal for Owner approval before proceeding with this DSI. If approved by Owner, the resulting contract change will be incorporated in the next formal Change Order. CITY OF KENNER COMMENTS CONCOURSE A 100% CONSTRUCTION DOCUMENTS Permit Comments ARCHITECTURAL, STRUCTURAL, MECHANICAL, ELECTRICAL, PLUMBING: -Refer to Attached EXHIBIT for Permit Responses and drawing list. -Revisions to drawings are clouded as CCAT-DSI REVISIONS TO TERMINAL Terminal Level 1: Curbside Maintenance Storage, Elevator Vendor Storage Skycap North & Fire Vender Storage ARCHITECTURAL, ELECTRICAL, MECHANICAL, TELECOM: Terminal Level 1: Curbside Maintenance Storage Terminal Level 1: Elevator Vendor Storage Terminal Level 1: Skycap North and Fire Vendor Storage Added ductwork to supply ventilation air to rooms: Vendor Storage (1091B), Vendor Storage (1091C). Added Unit Heater UH -and ductwork for supply ventilation to Maintenance Closet Removed exhaust duct and grille from room 1014 and added return duct and grille. Added Unit Heater UH-1015 to Skycap 1015 NT AG 4101, NT AG 5101, NT AT 1110, NT AT 1111, NT AT 1114, NT AT 1310, NT AT 1311, NT AT 1314, NT AT 1410, NT AT 1411, NT AT 1414, NT AT 6250, NT AT 2304, NT AT 4111, NT AT 6141, NT AT 6151 NT MT 1111, NT MT 1114, NT MG 6008, NT MG 6010 NT EG 7000, NT EG 7001, NT EG 7002, NT EG 7008, NT EG 7011, NT ET 1111A, NT ET 1114A, NT ET 1114B, NT ET 1214A, NT ET 2111A, NT ET 2114A, NT ET 2114B, NT PG 7001, NT PT 1101, NT PT 1104, NT PT 1114, NT PT 4001, NT TG 8001, NT TT 1111, NT TT 1114

4 ARCHITECTURAL, ELECTRICAL, MECHANICAL: Relocate Post Office to level 1 area T3. (RMs 1504B, 1504) Terminal Level 1: Add Post Office Recommendation: CCAT suggests Program Manager should request assistance from City of Kenner Post Office on Williams to assist with acquiring post office equipment which in the existing airport is supplied by USPS. (Post office boxes, mail drop, door hardware, any other items with USPS specific requirements.) NT AG 4101, NT AG 5101, NT AT 1110, NT AT 1113, NT AT1310, NT AT 1313, NT AT 1410, NT AT 1413, NT AT 4112, NT AT 4131 NT MT 1113, NT MT 1131, NT MG 6009, NT MG 6010 NT ET 1113B, NT ET 1113D, NT ET 2113B, NT ET 8113B Terminal Level 1: Add BA Ticket Office & Jan Storage by Post Office ARCHITECTURAL, ELECTRICAL, MECHANICAL, TELECOM: Revisions to Terminal Level 1: BA Ticket Office & Janitorial Storage by Post Office. Revised lighting, power and fire alarm for Level 1 Terminal West BA Office and Janitor Closet Provided new VAV and supply ductwork for Janitor Closet 1504D Provided new exhaust ductwork for Janitor Closet 1504D. Outlets & Microphones added. NT ET 1113B, NT ET 1113D, NT ET 2113B, NT ET 2113D, NT ET 8113B, NT ET 8113D NT TG 8002, NT TG 8040, NT TT 1113, NT MG 6011 NT MT 1113, NT MT 1213 NT AG 4101, NT AG 5101, NT AT 1110, NT AT 1113, NT AT 1310, NT AT 1313, NT AT 1410, NT AT 1413, NT AT P a g e

5 Terminal Level 1: Add Storage Rooms to CBIS ARCHITECTURAL, SECURITY, BAGGAGE, Mechanical & Electrical: Deletes Circulation 1495 and doors 1495A and 1495B Reroutes egress path from Bag Make Up 1400 directly to exterior through new door E1101A Relocates Exit Door E1495C and changes its ACS function Adds two rooms accessible from the exterior of the south wall: Storage 1495 with door E1495 & Storage 1417 with door E1417 Adds ramps running in the east west direction with step to the south for doors E1495 and E1417 Adds ramp running in the east direction with step to the south and west for door E1495C Relocates Baggage System Circuit Panel Provides HVAC for storage rooms Provides Lighting and Electric Outlets for Storage Rooms NT AG 4101, NT AG 5101, NT AT 1110, NT AT 1115, NT AT 1315 NT TT 1115, NT YG 8001, NT YG 8005, NT YT 1114, NT YT 1115 NT QT 1001, NT QT 1002, NT QT 1115C, NT QT 3110, NT QT 3111, NT QT 3112, NT QT 3113, NT QT 3116, NT QT 3117, NT QT 5000, NT QT 6003, NT QT 6007, NT QT 6012 Terminal Level 1: Add International Baggage Drop-Off ARCHITECTURAL, BAGGAGE, TELECOM, ELECTRICAL, & MECHANICAL: Adds International Baggage Drop off space to Terminal Level 1 Updates BHS to reflect new Drop off room Updated schedules to reflect new doors, outlets Added Light Fixtures, Power, & Control Modules Provided new VAV and supply ductwork to serve International baggage drop-off NT AG 4101, NT AG 5101, NT AG 5201, NT AT 1110, NT AT 1113, NT AT 1310, NT AT 1313, NT AT 1410, NT AT 1413, NT AT 4113 NT ET 1113B, NT ET 2113B, NT ET 8113B NT MT 1113, NT MG 6011 NT TG 8002, NT TT 1113, NT YG 800, NT YG 8004, NT YG 8011, NT YT 1110, NT YT 1113, NT YT 1313 NT QT 0101, NT QT 0110, NT QT 1100, NT QT 1110, NT QT 1113D, NT QT 1114C, NT QT 2114, NT QT 2124, NT QT 4306, NT QT P a g e

6 Terminal Level 2 & 3: Add Janitor Storage & Skycap ARCHITECTURAL, ELECTRICAL, MECHANICAL: Adds Janitors Storage Rooms 2096A and 2096B to Terminal Level 2, area T4, with associated Architecture, electrical, and mechanical work in the included drawings Adds a partial height wall extension and lighting update to wheel chair storage area to Terminal Level 3, area T1 NT AG 4102, NT AG 5102, NT AT 1120, NT AT 1124, NT AT 1130, NT AT 1131, NT AT 1320, NT AT 1330, NT AT 1331, NT AT 1420, NT AT 1424, NT AT 1430, NT AT 1431, NT AT 4031, NT AT 4431, NT AT 5009, NT AT 5131, NT AT 6250 NT MG 6010, NT MT 1124 NT EG 7002, NT EG 7010, NT EG 7011, NT ET 1214A, NT ET 1311A, NT ET 2214A, NT ET 2311A ARCHITECTURAL & MECHANICAL: Terminal Level 3: Add Office Shell Space Add Office Shell Space on Terminal Level 3 Relocate Jet diffusers on Level 2 to accommodate new bulkhead Configuration Note:: New Office area to be completed in future NT AG 4102, NT AG 5102, NT AG 5202, NT AT 1130, NT AT 1133, NT AT 1134, NT AT 1135, NT AT 1140, NT AT 1143, NT AT 1144, NT AT 1145, NT AT 1320, NT AT 1330, NT AT 1333, NT AT 1334, NT AT 1335, NT AT 1350, NT AT 1354, NT AT 4034, NT AT 5010, NT AT 5011, NT AT 7113, NT AT 7403, NT AT 7415,, NT AT 8133, NT AT 8134, NT AT 8135 Terminal Level 1: Downspout Alignment per RFI Special detail to accommodate non- standard inside corner support detail NT AT 3308 Clarify detail between Roadway and Terminal NT AT 1132, NT AT 7155 Terminal: Expansion Joint Revisions per RFI- Response 4 P a g e

7 Terminal: Hardware Revisions per RFI NT AG 5101, NT AG 5102, NT G 0051 Terminal: Air Column Relocation MECHANICAL: Relocate Air column Duct Distribution to coordinate with previously issued Architectural and Structural Documents NT MT 1121, NT MT 1122, NT MT 1131, NT MT 1132 Terminal: Bathroom Tile / Fixtures This contains clarifying dimensions for bathrooms including urinals, sinks, and metal panel locations to align placement logic with the toilets and ADA requirements. It also adjusts lengths of some walls slight amounts to clean up dimensions. NT AT 4011, NT AT 4015, NT AT 4023, NT AT 4024, NT AT 4025, NT AT 4031, NT AT 4034, NT AT 7152 REVISIONS TO CUP CUP: Interior Room Modifications ARCHITECTURE: At the Airports request, the attached drawings reconfigure the following CUP interior spaces: Office - A106 Office - A105 Curbside Janitors - A104 To the following spaces: Shop- A105 Office- A104 NT AG 4101, NT AG 5101, NT AG 5201, NT AT 1110, NT AT 1113, NT AT 1310, NT AT 1313, NT AT 1410, NT AT 1413, NT AT 4113, NT ET 1113B, NT ET 2113B, NT ET 8113B, NT MT 1113, NT MG 6011, NT TG 8002, NT TT 1113, NT YG 800, NT YG 8004, NT YG 8011, NT YT 1110, NT YT 1113, NT YT 1313, NT QT 0101, NT QT 0110, NT QT 1100, NT QT 1110, NT QT 1113D, NT QT 1114C, NT QT 2114, NT QT 2124, NT QT 4306, NT QT P a g e

8 REVISIONS TO CONCOURSE A Trash Room Modifications & QA / QC Wall Sections Modify Trash Room Rollup Doors sizes and configuration Modify Selected Wall Sections to accommodate QA /QC CCAT Reviews NT AA 1502, NT AA 1521, NT AA 1522, NT AA 2101, NT AA 2102, NT AA 2103, NT AA 3201 NT AA 3202, NT AA 3203, NT AA 3208, NT AA 3312, NT AA 4109, NT AA 4121 Slab edge at bag claim cross-bracing ARCHITECTURAL, STRUCTURAL: Edge of slab shifted 3 ½ south at bag claim to allow for 8 CMU to pass by cross-bracing NT AA 1111, NT AA 5203, NT SA 1011A, NT SA 1011B, NT SA 1111A, NT SA 1111B Adjusted sidewalk ramps at exterior doors Interior Metal Panel Layouts NT AA 6101, NT AA 6102, NT AA 6103 Miscellaneous Adjusted sidewalk ramps at exterior doors Height of the level 2 concessions soffit at the terminal expansion raised to match terminal design Approximately 3,000 SF of ACT-4 between H7-H9 removed from scope (TI by others) Clarification of divider strip locations at baggage claim area Minor clarifications to partition types, dimensions and finishes Relocated plumbing access panel from metal panel to gyp wall at WOMEN S 1806 Clarifications to ceiling details Furniture added to outbound search room NT AG 4010, NT AG 5120, NT AA 1001, NT AA 1002, NT AA 1003, NT AA 1004, NT AA 1121, NT AA 1122, NT AA 1321, NT AA 1323, NT AA 1324, NT AA , NT AA 4351, NT AA 4352, NT AA 4361, NT AA 4362, NT AA , NT AA 5102 thru NT AA 5106, NT AA 6301, NT AA 7111 thru NT AA 7113, NT AA 8102, NT AA 8201 thru NT AA 8203, NT AA 8301 thru NT AA 8303, NT AA P a g e

9 Clarifications to door material, dimensions and hardware NT AG 5103 REVISIONS TO FIS Door Schedule Clarifications to millwork finishes per RFI Clarification to processing booth glazing per RFI Clarification to GE counters per RFI Clarification to millwork per RFI CBP Millwork Clarifications NT AT 7414, NT AT 7422, NT AT 7423, NT AT 7418, NT AT 7420, NT AT 7421, NT AT Locations coordinated with civil drawings per ATK-DSI-0023 REVISIONS TO CONCOURSE B+C High Mast Light Poles Fixed bridge and PBB locations to be provided by CMAR NT AC 1511, NT AC 1521, NT AC 1522 Fixed Bridge Plans Exterior Metal Panel Clarifications Clarifications to location and details for embossed and flat metal panel cladding at gate portals and metal panel skirt NT AC 2101, NT AC 2102, NT AC 2103, NT AC 2104, NT AC 2105, NT AC 3201, NT AC 3302, NT AC 3303, NT AC 3304, NT AC 3305 & NT AC 3306, NT AC 4103, NT AC 4104, NT AC 4106, NT AC 4202, NT AC 4203, NT AC 4301, NT AC 5201, NT AC P a g e

10 Clarifications to door material, dimensions and hardware NT AG 5110, NT AG 5111 Door Schedule Clarifications Holdroom Furniture Coordination with JWI holdroom furniture and millwork layout Addition of 5 gate counters for a total of 31 gate counters NT AC 9121, NT AC 9122, NT AC 9123, NT AC 9124, NT AC 9125, NT AC 9126 REVISIONS TO CIVIL CIVIL: CI CG 2101 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CG 2102 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CG 2103 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CG 2104 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CG 2105 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CG 2106 (Added note Profiles are for verification of conformance with FAA design circulars. Concrete pavement shall be constructed per the elevations shown on the joint elevation sheets. ) CI CJ 1003 (Co-ordinated with Argus fuel pit locations for which slabs need to be reinforced) CI CJ 1007 (Co-ordinated with Argus fuel pit locations for which slabs need to be reinforced) CI CJ 1008 (Co-ordinated with Argus fuel pit locations for which slabs need to be reinforced) 8 P a g e

11 REVISIONS TO TELECOM VOLUME NT TG 6114 Added BMU Monitors to EVIDS Block Diagram. NT TG 7003 Added detail for data outlet Type U, for use at BMU monitor locations. NT TG 7021 Added detail for EVIDS Type BID-C, for use at BMU monitor locations. NT TG 8001 Deleted data outlets 1T1-06, 1T1-07, 1T1-11, 1T1-12, 1T1-13, and 1T1-14 from Outlet Schedule. NT TG 8002 Added data outlets 1T3-85 and 1T3-86 at International Baggage Drop-Off Room; added data outlet 1T3-98 at BA BSO; deleted outlets 1T4-48, 1T4-50, 1T4-52, 1T4-54, 1T4-56, 1T4-58, 1T4-60, 1T4-61, 1T4-62, 1T4-63, 1T4-64, 1T4-65, 1T4-66, 1T4-67, 1T4-68, 1T4-69, 1T4-70, 1T4-71, 1T4-101, 1T4-107, and 1T4-108 due to revised BMU Monitor locations; changed outlet types for outlets 1T4-47, 1T4-49, 1T4-51, 1T4-53, 1T4-55, 1T4-57, 1T4-99 at BMU Monitor locations. NT TG 8020 Added BMU Monitors to EVIDS Schedule. NT TG 8040 Added PA System microphone for BA BSO Room. NT TT 1111 Revised in CCAT-DSI NT TT 1113 Added two data outlets at International Baggage Drop-Off Room; added one data outlet and PA System microphone at BA BSO. NT TT 1114 Added BMU Monitors; deleted data outlets that were not needed for BMU Monitor locations; changed data outlet types for remaining data outlets at BMU Monitor locations. NT TT 1115 Revised Comm Room boundary lines due to added storage rooms near CBIS. VOLUME NT YG 8001 Added SACS doors 1496B and E1495C to ACS Door Schedule; removed SACS doors 1495A, 1495B, and 1495C from ACS Door Schedule. NT YG 8005 SACS door E1495C to IFP Schedule. NT YT 1110 Revised secure line around International Baggage Drop-Off room. NT YT 1113 Added SACS door 1496B at International Baggage Drop-Off Room. NT YT 1114 Deleted SACS door 1495A. VOLUME NT TA 1111 Added data outlet in Trash Room; swapped locations of Comm 1828 and CBP Comm 1804; reconfigured cable tray and backbone conduits to align with communications rooms. NT TA 4111 Reconfigured equipment in Comm 1828 due to change in room location. NT TA 4112 Reconfigured equipment in CBP Comm 1804 due to change in room location. NT YA 1110 Revised security zone boundary line to correspond with swapped locations of Comm 1828 and CBP Comm NT YA 1111 Added SACS to doors E1830A and E1830C; added camera NT-1-A1-13; revised location of camera NT-1- A1-01, SACS device 1804-DA, and SACS doors 1804 and 1828 to correspond with swapped locations of Comm 1825 and CBP Comm NT YG 8004 Added SACS doors E1830A and E1830C to SACS Door Schedule. NT YG 8006 Added SACS doors E1830A and E1830C to IFP Schedule. NT YG 8014 Added camera N1-1-A1-13 to VSS Schedule. VOLUME 4 PG T 1103 Revised backbone conduits to align with Communications Room location on Level 2, deleted underground conduit to former entry gate location that was removed when Parking Garage was expanded. PG T 1105 Deleted underground conduit to former entry gate location on drawing PG T 1103 that was removed when Parking Garage was expanded. PG T 1203 Moved callout for relocated Communications Room. PG T 1303 Moved location of conduit riser to align with relocated Communications Rooms on Levels 2 and 5. PG T 1403 Moved location of conduit riser to align with relocated Communications Rooms on Levels 2 and 5. PG T 1503 Moved callout for relocated Communications Room. PG T 4104 Revised enlarged floor plan and enlarged overhead plan due to relocation of Communications Room. PG T 4107 Revised enlarged floor plan and enlarged overhead plan due to relocation of Communications Room. PG Y 1203 Moved ACS symbol for door 211 to align with relocated Communications Room. PG Y 1503 Moved ACS symbol for door 511 to align with relocated Communications Room. 9 P a g e

12 VOLUME 5 UP T 1001A Revised data outlets at Office and Shop Rooms, deleted outlet 1UP-004. UP T 6000 Revised Outlet Schedule with deleted outlet 1UP-004. REVISIONS TO MECHANICAL Post Office i. NT MG updated VAV to serve janitor's closet ii. NT MG updated VAV to serve post office iii. NT MT Provided new VAV and supply ductwork to serve post office iv. NT MT Provided new exhaust and supply for Janitor closet Added air distribution to Maintenance and Skycap Architecture 3rd Floor slab Expansion i. NT MT Relocated diffusers and revised distribution due to new ceiling plan International Baggage Drop-Off i. NT MT Provide new VAV and ductwork to supply international baggage drop off ii. NT MG Provide new VAV Terminal Level 1: Curbside Maintenance Storage, Elevator Vendor Storage, Skycap North and Fire Vendor Storage i. NT MT 1111 Added ductwork to supply vendor storage, removed exhaust duct and grille from 1014 and replaced with return duct and grille, ii. NT MT added UH and ductwork to supply maintenance closet iii. NT MT added unit heater to skycap iv. NT MT added piping for UH in maintenance closet v. NT MG 6008 added unit heaters to schedule vi. NT MG 6010 added VAV to schedule for Skycap, edited airflows to support revised ductwork Terminal Level 2&3 Janitor Storage & Skycap i. NT MT 1124 Added ductwork to supply ventilation air to janitor storage rooms. ii. NT MG 6010 updated VAV cfms for janitor closet changes BA Ticket Office & Jan Storage by Post Office i. NT MT 1113 Provide new VAV and supply ductwork for janitor closet. ii. NT MT 1213 Provide new exhaust ductwork for janitor closet. iii. NT MG 6011 add VAV serving janitor closet Added storage rooms to CBIS i. NT MG 6014 Relocated CUH units to storage rooms ii. NT MT 1115 Added ventilation to new storage room and increased ventilation to existing room Concourse A Trash Room /QAQC Wall Sections i. NT MA 1111 Added FCU and relocated CUH to match new room layout ii. NT MA 2111 Added FCU and relocated CUH to match new room layout iii. NT MG 6127 Added FCU to schedule Terminal Level 1 MER Alignment i. NT MT Rotated MER alignment for Terminal 1 st Level SW MER ii. NT MT Rotated MER alignment for Terminal 1 st Level SW MER iii. NT MT Rotated MER alignment for Terminal 1 st Level SW MER iv. NT MT Rotated MER alignment for Terminal 1 st Level SW MER 10 P a g e

13 SHG-DSI-0024 / RFI i. NT MC Updated waterside riser diagram to match current design and more clearly show required isolation valves ii. NT MC Updated waterside riser diagram to match current design and more clearly show required isolation valves iii. NT MT Updated waterside riser diagram to match current design and to show required isolation valves iv. NT MT Updated waterside riser diagram to match current design and to show required isolation valves CCAT-DSI-0086 / SHG-DSI-0025: Revised the level 3 MER. Shifting circulation and office AHU s. Revised ductwork and piping for the associated AHU s. Updated piping and ductwork sizes based on previously revised DOAS, Retail, and Makeup units. Revised duct connections into the concourse from the level 3 MER. i. NT MT Relocated associated duct distribution ii. NT MT Relocated associated duct distribution iii. NT MT Relocated Air Columns iv. NT MT Relocated Air Columns REVISIONS TO LIFE SAFETY CCAT-DSI-0044 updates the Life Safety Drawings of the project to include changes required to the Terminal Building and Concourses B and C that are required to accommodate the addition of Concourse A, updates to the FIS areas, and the following updates to the Terminal portion of the building; Post Office (Level 1), International Baggage Drop (Level 1), Storage under Escalators (Level 1), 3 rd Floor Office Expansion Shell Space, West Mechanical Room Reconfiguration (Level 3), and Concourse A Trash Room (Level 1). Updates to life safety sheets include relocation of rated partitions, updates to occupant load and egress capacity calculations, and revisions of egress routes, where necessary to accommodate Architectural design changes SHEET LIST: NT GL 0002, NT GL 0005, NT GL 0110, NT GL 0111, NT GL 0120, NT GL 0121, NT GL 0130, NT GL 0131, NT GL 1010, NT GL 1020, NT GL 1030, NT GL 1110, NT GL 1120, NT GL 1130, NT GL 1213, NT GL 1214, NT GL 1215, NT GL 1223, NT GL 1224, NT GL 1310, NT GL 1320, NT GL 1330, NT GL 2112, NT GL 2120, NT GL 2217, NT GL 2231, NT GL 2233, NT GL 2234, NT GL 2235, NT GL 2312, NT GL 2313, & NT GL 2322 REVISIONS TO BAGGAGE SYSTEMS QA1100 QA1101 QA1102 QA1113A QA1113B 1. Flipped drive and platform to avoid interference with escalator pit. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 1. Flipped drive and platform to avoid interference with escalator pit. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 1. Flipped drive and platform to avoid interference with escalator pit. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 1.Addition of International re-check system. Only RC1-12 merge to be installed as 11 P a g e

14 QA1114A QA1114B QA1116A QA1116B 1. Lowered conveyor to 9'-4" el.to avoid clash. Moved incline down the line to still achieve 9'-9" el. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 1. Lowered conveyor to 9'-4" el.to avoid clash. Moved incline down the line to still achieve 9'-9" el. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 1. Flipped drive and platform to avoid interference with escalator pit. 1. Flipped drive and platform to avoid interference with escalator pit. QT0110 QT1001 QT1002 QT1100 QT1110 QT1113D QT1114C QT1115D QT1310 QT1311B QT1312B QT 1314B QT1315A QT Added Re-check conveyors to manifest. 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 1. Lowered conveyor to 9'-4" el.to avoid clash. Moved incline down the line to still achieve 9'-9" el. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 1. Extended ticket counters to match ticketing layout. 1. Extended ticket counters to match ticketing layout. 1. Extended ticket counters to match ticketing layout. 1. Extended ticket counters to match ticketing layout. 1. Extended ticket counters to match ticketing layout. 1. Lowered conveyor to 9'-4" el.to avoid clash. Moved incline down the line to still achieve 9'-9" el. 2. Addition of International re-check system. Only RC1-12 merge to be installed as 12 P a g e

15 QT2114 QT2124 QT2125 QT3110 QT3111 QT3112 QT3113 QT3116 QT3117 QT4306 QT5000 QT5001 QT6003 QT6007 QT6009 QT Moved MCPs and PDP from closed rooms to the open CBIS area. 1.Addition of International re-check system. Only RC1-12 merge to be installed as 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 1. Added new sheet for Re-check sections. 2. Moved MCPs and PDP from closed rooms to the open CBIS area. 1. Added Re-check conveyors to power source manifest. 1.Addition of International re-check system. Only RC1-12 merge to be installed as 13 P a g e

16 ATTACHED EXHIBITS City of Kenner Permit Responses CONCOURSE A 100% CONSTRUCTION DOCUMENTS List of previous DSI included within CCAT-DSI-0044 CONFORMED SET FORTHCOMING REVISIONS ARCHITECTURAL, STRUCTURAL, MECHANICAL, TELECOM, ELECTRICAL, PLUMBING: MEP coordination of Third Floor Terminal MSY office buildout MEP coordination of RCP under third floor MSY office buildout Architectural enclosure for valve closet for radiant floor at west concession Coordination of revised PBB layouts Coordination of revised Apron lighting Location of curbside counters BMU Monitor Locations MEP coordination of CBIS storage rooms MEP coordination of Expansion Joint at curbside Coordinate plumbing with Architectural revision at Concourse A level 1 restroom Minor wall revisions to Concourse Apron tenant demark walls CIVIL: MSMM and Atkins are working on a revised outfall, estimated delivery: July 10th ATKC revision for pavement joint elevations along drainage inlet rows of B (east/west) and C (west) July 14th END COVER LETTER 14 P a g e