IntelliTrac Quick Reference Guide

Transcription

1 Display Part Number Rev 2 fter you start IntelliTrac and select your logging drive G4 hard drive US flash drive the Map screen appears (shown below). Toggle Zoom/Pan mode on/off Date and time Power Header area User-defined fields (SETUP > SETUP > SCREEN > Displays, Left Display and Right Display fields) User-defined fields (SETUP > SETUP > SCREEN > Displays, fields 1-3) Direction/pattern Zoom in Double-click compass to toggle between uto and Manual zoom Codinates Hotkeys (hide/ display using HOTKEYS button) Swath #, GPS status Swath width Ground speed ircraft heading Snap to position Moving Map area GPS & differential status indicats Current field/ total areas (and reset areas) Zoom out Log On/Off indicat Remaining volume (and reset volume) Cycle through view of aircraft, each polygon in a job, all polygons, and log (if log is loaded to view) Data area Show calculat Show main Setup menu Show Keypad Hide/show Hotkeys Save position in field Return to mark Decrement swath Quick Keys dvance swath

2 Lightbar Cross-track distance Cross-track direction (R [right] L [left]) Swath number Heading angle Cross-track distance Swath line Heading angle Follow the direction of the lights to crect cross-track err Swath line Lightbar Messages Lightbar Display Definition Waiting : appears and center yellow LEDs remain lit until an point is entered. Enter an point. Waiting : Upper LED row flashes until a point is entered. Enter a point. Waiting C: Left display will show C followed by the current swath number. Enter a C point. Right display will show distance to nearest swath. Swath double spray warning: Upper LEDs flash when spraying a previously sprayed swath. These will flash until the swath number is changed. Loss of GPS: Center yellow LEDs blink. Reboot system and check f receiver and power status lights. Refer to the IntelliTrac User Guide f me infmation. Loss of Differential: Lower center yellow LED flashes. Check status lights on the G4. Reboot and wait up to 5 minutes f a better solution.

3 Common s Shut down IntelliTrac and exit to Windows Press... Hold Power button f 3 seconds ssign Hotkeys Clear active guidance from display screen Set line to current swath Toggle daytime/night-time screen cols CPTE Clear\Pattern\Enter CPT Clear\Pattern\dv (UP) STST Set\Set Logs See also Transferring Data on second to last page. egin logging Start a new log Logging is enabled by default and begins automatically anytime you fly above 45.0 mph. You can verify logging is enabled via the Logging is Ready notification in the bottom right of the Map screen. Turn logging off Enter log details View list of logs Delete logs Delete individual logs... Delete all logs...

4 Routes and Waypoints View all active routes (displayed on the left side of the screen). Press ROUTE to step through each active route. View active waypoints (displayed on the left side of the screen) Save a waypoint by name Save a waypoint by number Set (guide to) a waypoint by name IFWY Info\Waypoint Set (guide to) a waypoint by number Delete a waypoint ssign a waypoint to a route then select a name Waypoints are assigned to the current route. To change your current route while flying, press... Clear waypoint guidance from the display screen (but not from memy) CWPE Clear\Waypoint\Enter Edit a waypoint Set radius then edit the desired waypoint. Recall a route to open the Waypoints menu

5 Jobs and Polygons Display all jobs with number of associated polygons and patterns Manually create a polygon IFJ Info\Info... Create/edit a polygon Delete last entered polygon point Save a polygon Clear all polygons from screen (but not from memy) Go to specific polygon Recall a job (all polygons) Save a job by name (verify JOS y Name is set to YES in dvanced Options Setup window) Save a job by number (verify JOS y Name is set to NO in dvanced Options Setup window) You MUST save a polygon to a job it will be deleted when your reboot IntelliTrac.

6 asic Menu System Me options Me options

7 Marks Save a mark (1-9) Save a mark (10-99) Display mark infmation marks used, job name, log associated with mark IFMK Info\Mark Recall a mark Return to last spray point (recalls all infmation from last sprayed job) Delete a mark Flow Control ccess Flow Control setup IFIF Info\Info Toggle between full boom and half boom setting You must first enable oom Shutoff Left Right in the Spray oom Setup window (press SETUP > SETUP > FLOW CTRL > SETUP > SETUP).

8 Patterns Go to swath number n Show which swaths have NOT been sprayed Select a pattern (press PTTERN repeatedly to cycle through patterns) Change pattern direction Make closest swath the current swath (f Open patterns only) dvance/decrement swath (if not using remote swath advance) then

9 Pattern Types Patterns are open type (unlimited swaths) closed type (swaths limited by defined field width). Patterns with a C point are closed patterns. ack-to-ack Skip (KKS) ack-to-ack (K-K) Press to switch from odd to even swaths. C D F E Multi ack-to-ack (M2K) C C C C Racetrack Quick Racetrack Reverse Racetrack QuickTrack X (X = no. swath fixed distance - select at prompt) Squeeze Expand

10 Zooming/Panning Use outer arrows to pan Use CENTER button to center You can use either the Zoom/Pan window (left) the Moving Map area controls (right) to zoom/pan the map Zoom in Zoom out Use ZOOM buttons to zoom in and out Press befe you fly your pattern to autozoom in/ out to keep pattern in view while flying Pan the screen by pressing anywhere in the Moving Map area and then dragging (Pan mode must be ON) Tip! Press the CENTER button to sequentially toggle through centering the following: - ircraft - ll polygons - Each active polygon in a job - Log (if log is loaded to view) Transferring Data Press... Transfer data between the G4 hard drive and US flash drive You can transfer logs, jobs, marks, waypoints, and pilot settings. Transfer all log files only This allows you to quickly transfer all log files directly from the G4 hard drive to a US flash drive without having to individually select each log file in the File Transfer window.

11 uto-pplying Lines to a Polygon Press... First, load a job that has polygons. Then, have IntelliTrac apply an line on the side of the lowest numbered polygon that will result in the least number of swaths. Press Change Poly to toggle through the job s other polygons. Press Rotate to rotate the line around the polygon sides (in longest to shtest der). Press Left/Right to switch the array. Copyright Hemisphere GPS (2012). ll rights reserved. HEMISPHERE GPS, the Hemisphere GPS logo, G4, and IntelliTrac are proprietary trademarks of Hemisphere GPS. Other trademarks are the properties of their respective owners.