Adjust model for 3D Printing. Scaling 13,0600,1489,1604(SP6)
|
|
|
- Monica Walsh
- 5 years ago
- Views:
Transcription
1 Adjust model for 3D Printing Scaling 13,0600,1489,1604(SP6)
2 In this exercise, we will learn to create Scaling to added 3DP component. As the printed part cools down, it shrinks. Therefore, it may be required to scale it up so that it shrinks to the correct size. To use this command we need to follow few steps (guided): Load 3DXpert-Exercise-Scaling_Start.SLDPRT to SOLIDWORKS Launch 3DXpert for SOLIDWORKS. Add shrinkage compensation.! Notice/ Remember Left mouse button name is "pick" Middle mouse button name is "Exit" Right mouse button name is "Click" 1. Load 3DXpert-Exercise-Scaling_Start.SLDPRT to SOLIDWORKS from the folder that it was downloaded to. 2. From the Additive Manufacturing tab pick 3XPert for SOLIDWORKS command. New 3D Printing Project Additive Manufacturing This command will launch 3DXpert for SOLIDWORKS. 3. After the 3DXpert for SOLIDWORKS is invoked, new window will open: Pick Keep Original Position & Orientation and OK: In this window we set the basic positioning of the part on the tray Keep Original Orientation means that the part will not rotate to any direction - XYZ of the part will be parallel to the XYZ of the tray - but the center of the bounded silhouette will move to the center of tray. Keep Original Position & Orientation means that the part will not rotate to any direction - XYZ of the part will be parallel to the XYZ of the tray - but the center of the part (UCS 0,0) will move to the center of tray. 3DXPERT Adjust model for 3D Printing - Scaling 2
3 After the file is open the screen will look like this: 3DP Objects Tree 3D Printing Process Guide Assembly Tab 3DP Objects Tab Tray Display Area Part on Tray 3D Printing Data Notice the Process Guide on the right side of the screen. This guide contains most of the functionality to enable preparing the part for printing. 4. Save the project, pick the Save command on top left corner. Save This command will open the 3DXpert for SOLIDWORKS Explorer. Save the file to the same folder with the downloaded files. 3D Printing Project Name Save 3DXPERT Adjust model for 3D Printing - Scaling 3
4 After adding the 3DP component the tray will look like this: From a TOP view From ISO view 5. Pick shrinkage compensation command from the 3D Printing Process Guide. shrinkage compensation 1) Pick object 2) Pick a pivot point 3) Set parameters "Preview" the result without executing To approve and finish use the "OK" To approve and continue use the "Apply". "Cancel" exit the comand without keep changes 3DXPERT Adjust model for 3D Printing - Scaling 4
5 Since the command have some defaults its "jumps" to the last stage in this command. 6. Pick the first stage in the Feature Gide - Pick object. At the first stage it is possible to choose between All Objects (default) and By Pick. The option All Objects does the same shrinkage compensation to all and in case of By Pick we have to repeat the command as needed. Keep All Objects and Exit (left mouse button) to continue. 7. At the second stage Pick a pivot point is possible to choose between Center of Selected Geometry (default) and Free Selection to pick any point as a pivot point. Keep Center of Selected Geometry and Exit (left mouse button) to continue. 8. Last stage Set parameters. Set parameters as shown in the following pictures, to approve and finish use the "OK": Uniform Show as Factor Non-Uniform Show as Factor The Uniform parameter is used when the shrinkage compensation is the same to all main directions (XYZ) and can be changed to Non-Uniform for different values can be used for each main directions (X-Y-Z) separately. In any method chosen, the Volume Change Rate is displayed. 3DXPERT Adjust model for 3D Printing - Scaling 5
6 It is possible to show the values as Factor or as Percentage. Uniform Show as Percentage Non-Uniform Show as Percentage After shrinkage compensation setting is finished and while the command is active the user can save as Predefined Factor (for a certain material or printing technology for example) and to use it next time.! Please notice: when using Non-Uniform compensation with different values in any main plan direction ( i.e. XY plane), cylinder in that plane are deformed End of Exercise. 3DXPERT Adjust model for 3D Printing - Scaling 6
Create a 3D Printing Project. New Project-set part on Tray 13,0600,1489,1616(SP6)
Create a 3D Printing Project New Project-set part on Tray 13,0600,1489,1616(SP6) In this exercise, we will learn to create New Project-set part on Tray. To create a new project and set the tray we need
Support creation & Verification. Automatic region creation 13,0600,1489,1616(SP6)
Support creation & Verification 13,0600,1489,1616(SP6) In this exercise, we will learn the foundation of. Region creation is required to identify those regions where a support is needed to the tray. In
Adjust model for 3D Printing. Direct modeling tools 13,0600,1489,1616(SP6)
Adjust model for 3D Printing Direct modeling tools 13,0600,1489,1616(SP6) Sometimes, the model needs to be prepared or adapted for printing. Adding material, change of a draft angles are an example. In
Adjust model for 3D Printing. Positioning - Orientate the part 13,0600,1489,1604(SP6)
Adjust model for 3D Printing 13,0600,1489,1604(SP6) In this document, we will learn about. Position and Orientate a Body means that we move and rotate the body to fit our 3D printing considerations. Typical
Adjust model for 3D Printing. Positioning - Consider Other Parts 13,0600,1489,1635(SP6)
Adjust model for 3D Printing 13,0600,1489,1635(SP6) In this exercise, we will learn about parts positioning, and in particular, about the option Consider Other Parts. As we Position and Orientate parts
Slicing. Slice multiple parts 13,0601,1489,1664(SP6P1)
Slicing 13,0601,1489,1664(SP6P1) In this exercise, we will learn how to perform Slicing on multiple part. Slicing is the stage where the printing layers are set according to the printer definition or printing
Analysis Tools. Check and Fix - Mesh 13,0601,1489,1664(SP6P1)
Analysis Tools 13,0601,1489,1664(SP6P1) In this exercise, we will learn to use Check and Fix on a Mesh model, as part of Printability Check. In general, the possible issues with printing are divided to
ADJUST MODEL FOR 3D PRINTING Printability Checks. Tutorial_V3 : 13,0600,1489,1616(SP6)
ADJUST MODEL FOR 3D PRINTING Printability Checks Tutorial_V3 : 13,0600,1489,1616(SP6) Introduction 3DXPert for SOLIDOWRKS includes several Analysis Tools, available from the 3DP Analysis menu This exercise
ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
Autodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
Working Environment. Environment Part 13,0600,1489,1598(SP6)
Working Environment Environment Part 13,0600,1489,1598(SP6) In this document, we will learn the Environment Part file. The part environment is the basic 3D cad environment for design and managing 3D CAD
Engineering. Statics Labs SDC. with SOLIDWORKS Motion Includes. Huei-Huang Lee. Better Textbooks. Lower Prices.
Engineering Includes Video demonstrations of the exercises in the book Statics Labs with SOLIDWORKS Motion 2015 Huei-Huang Lee Multimedia Disc SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com
Panel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
Figure 1: The excel document used to personalize a race car by changing the values of 5 parameters
How to Make a Personalized Race Car 1. Open the excel document entitled Parametric Flexitop Car Parameters.xlsx. 2. The excel document should be on the Sliders tab as seen in Figure 1. If not, click on
Web-based Configuration. First, setup motion detection windows in the web-based configuration of the camera.
How do I record motion using IP surveillance? To schedule video recording with motion detection, you must first enable this feature on the Internet camera. This can serve as a security device by recording
SolidWorks 2015 User Interface
SolidWorks 2015 User Interface SolidWorks a Dassault Systèmes Product Starting SolidWorks 1) On the desktop, double-click or from the start menu select: All Programs SOLIDWORKS 2015 SOLIDWORKS 2015. 2)
Memo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
Introduction to INTERFACExpress and Data Entry
Introduction to INTERFACExpress and Data Entry Welcome to INTERFACExpress, the new MLS system brought to you by RealtyServer. This system accesses a central database of listings using an Internet connection
3D Body. Summary. Modified by Admin on Sep 13, Parent page: Objects
3D Body Old Content - visit altium.com/documentation Modified by Admin on Sep 13, 2017 Parent page: Objects A sphere, a cylinder and 4 extruded rectangles have been used to create the 3D body for an LED.
Display. Introduction page 67 2D Images page 68. All Orientations page 69 Single Image page 70 3D Images page 71
Display Introduction page 67 2D Images page 68 All Orientations page 69 Single Image page 70 3D Images page 71 Intersecting Sections page 71 Cube Sections page 72 Render page 73 1. Tissue Maps page 77
SOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
ADD A 3-D PIE CHART TO THE WORKBOOK
ADD A 3-D PIE CHART TO THE WORKBOOK A pie chart is an easy way to show the relationship of items to the whole. In this exercise, you will be creating a Pie Chart that will show the relationship between
MASTERCAM DYNAMIC MILLING TUTORIAL. June 2018
MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject
Solid Problem Ten. In this chapter, you will learn the following to World Class standards:
C h a p t e r 11 Solid Problem Ten In this chapter, you will learn the following to World Class standards: 1. Sketch of Solid Problem Ten 2. Starting a 3D Part Drawing 3. Modifying How the UCS Icon is
Wheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
LAB_3: Main Toolbar buttons PART 2
0 Main Toolbar The main toolbar in its floating form Cloning Objects Make a selection. > Edit menu > Clone Make a selection. > Hold down Shift key. > Move, rotate, or scale the selection with the mouse.
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
First Steps - Ball Valve Design
COSMOSFloWorks 2004 Tutorial 1 First Steps - Ball Valve Design This First Steps tutorial covers the flow of water through a ball valve assembly before and after some design changes. The objective is to
Assembly Modeling Constraints
Assembly Modeling Constraints College of Engineering Engineering Education Innovation Center Rev: 20130715 AJP Assembly Modeling Constraints 1 Assemblies Assemblies are collections of 3D parts that form
Chair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
DMU Engineering Analysis Review
DMU Engineering Analysis Review Overview Conventions What's New? Getting Started Entering DMU Engineering Analysis Review Workbench Generating an Image Visualizing Extrema Generating a Basic Analysis Report
Skateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
SolidWorks Import Tutorial
SolidWorks Import Tutorial Current Item: SolidWorks Import Tutorial Before You Begin This tutorial will step you through the process of exporting a file from SolidWorks and importing it into Bend-Tech.
TUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
PowerPoint X. 1. The Project Gallery window with the PowerPoint presentation icon already selected. 2. Click on OK.
PowerPoint X Launching PowerPointX 1. Start PowerPointX by clicking on the PowerPoint icon in the dock or finding it in the hard drive in the Applications folder under Microsoft PowerPoint. PowerPoint
Column - solid section
1 Column - solid section This example demonstrates how how to design a column with an arbitrary cross-section defined by the user. The model is a simple one member column, loaded with an axial load and
Exercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
Assembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
Spring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
Basic Electrodes. CimatronE 8.5 Tutorial
Basic Electrodes CimatronE 8.5 Tutorial Table of Contents Electrodes... 1 Attachment... 1 Electrodes Introduction... 1 Attachment... 1 Blank & Electrode UCS... 7 Blank & Electrode UCS... 7 Extension...
Terminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
Sliding Split Tube Telescope
LESSON 15 Sliding Split Tube Telescope Objectives: Shell-to-shell contact -accounting for shell thickness. Creating boundary conditions and loads by way of rigid surfaces. Simulate large displacements,
Creating a Web Presentation
LESSON 9 Creating a Web Presentation 9.1 After completing this lesson, you will be able to: Create an agenda slide or home page. Create a hyperlink to a slide. Create a Web presentation with the AutoContent
Objectives This tutorial demonstrates how to use feature objects points, arcs and polygons to make grid independent conceptual models.
v. 9.0 GMS 9.0 Tutorial Use points, arcs and polygons to make grid independent conceptual models Objectives This tutorial demonstrates how to use feature objects points, arcs and polygons to make grid
Bottom Truss ANALYSIS
Chapter 3 Beam Bottom Truss ANALYSIS A. Enable SolidWorks Simulation. Step 1. If necessary, open your Beam1 part file. Step 2. If necessary, turn on SolidWorks Simulation. To turn on Solid- Works Simulation,
PowerPoint Launching PowerPointX
PowerPoint 2004 Launching PowerPointX 1. Start PowerPoint by clicking on the PowerPoint icon in the dock or finding it in the hard drive in the Applications folder under Microsoft Office 2004. PowerPoint
Simple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
Microsoft Windows 7 - Illustrated Unit A: Introducing Windows 7
Microsoft Windows 7 - Illustrated Unit A: Introducing Windows 7 Objectives Start Windows and view the desktop Use pointing devices Use the Start button Use the taskbar Work with windows 2 Objectives Use
LESSON 14 LEARNING OBJECTIVES. After completing this lesson, you will be able to:
LEARNING OBJECTIVES After completing this lesson, you will be able to: 1. Construct 6 Solid model Primitives: Box, Sphere, Cylinder, Cone, Wedge and Torus LESSON 14 CONSTRUCTING SOLID PRIMITIVES AutoCAD
User Guide. for. JewelCAD Professional Version 2.0
User Guide Page 1 of 121 User Guide for JewelCAD Professional Version 2.0-1 - User Guide Page 2 of 121 Table of Content 1. Introduction... 7 1.1. Purpose of this document... 7 2. Launch JewelCAD Professional
PhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
Lesson 2 Constructive Solid Geometry Concept. Parametric Modeling with I-DEAS 2-1
Lesson 2 Constructive Solid Geometry Concept Parametric Modeling with I-DEAS 2-1 2-2 Parametric Modeling with I-DEAS Introduction In the 1980s, one of the main advancements in Solid Modeling was the development
Training Guide Getting Started with WorkXplore 3D
Training Guide Getting Started with WorkXplore 3D Table of Contents Table of Contents 1 Training Guide Objectives 1-1 2 WorkXplore 3D Environment 2-1 3 Importing and Opening CAD Files 3-1 3.1 Importing
Chapter 4 Feature Design Tree
4-1 Chapter 4 Feature Design Tree Understand Feature Interactions Use the FeatureManager Design Tree Modify and Update Feature Dimensions Perform History-Based Part Modifications Change the Names of Created
Views of a 3-D Clevis
LESSON 5 Views of a 3-D Clevis Objectives: To become familiar with different view options. To create and modify z-axis and arbitrary clipping planes. PATRAN301ExerciseWorkbook-Release7.5 5-1 5-2 PATRAN
Flow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
Filename:QIM-DP-05-Approve Quality Reject and Set in Process Page 1 of 12
This Desktop Procedure demonstrates the steps to View & Download Attachment, Upload a QRA Attachment, and then Set the Issue Status to In Process in QIM. 1. Click the Worklists tab in the Navigation Pane.
Need help? Call: / DOCMAIL: PRINT DRIVER USER GUIDE
Need help? Call: 01761 409701 / 409702 DOCMAIL: PRINT DRIVER USER GUIDE July 2017 1 GETTING STARTED Create your letter document... If you are sending to more than one address you will have to complete
1 - Introduction Training Guide Objectives WorkXplore Environment Importing and Opening CAD Files 5
Table Of Contents 1.1 - Training Guide Objectives Table Of Contents 1 - Introduction 3 1.1 - Training Guide Objectives... 3 1.2 - WorkXplore Environment... 3 2 - Importing and Opening CAD Files 5 2.1 -
CHAPTER 1. EZ-MILL PRO / 3D MACHINING WIZARD TUTORIAL 1-2
1. TABLE OF CONTENTS 1. TABLE OF CONTENTS 1 CHAPTER 1. EZ-MILL PRO / 3D MACHINING WIZARD TUTORIAL 1-2 Overview... 1-2 Cavity Machining... 1-2 Basic Programming Steps... 1-3 The Part... 1-4 Setting the
General Information Project management Introduction... 4 Getting Started Input geometry... 7
Tutorial Shell Tutorial Shell All information in this document is subject to modification without prior notice. No part or this manual may be reproduced, stored in a database or retrieval system or published,
SCENE FILE MANIPULATION SCENE FILE MANIPULATION GETTING STARTED MODELING ANIMATION MATERIALS + MAPPING RENDERING. Saving Files. Save.
SCENE FILE MANIPULATION SCENE FILE MANIPULATION There are several things you can do with a scene file in 3ds Max. You can save a file, save a file temporarily and retrieve it, and combine scene files.
Project 3. Top Down Design In Context. Below are the desired outcomes and usage competencies based upon the completion of this Project.
Assembly Modeling with SolidWorks Project 3 Below are the desired outcomes and usage competencies based upon the completion of this Project. Project Desired Outcomes: 2AXIS-TRANSFER Assembly. PLATE-B Part.
This document shows you how to set the parameters for the ModuleWorks Material Removal Simulation.
Table of Contents Introduction:... 3 Select Profile:... 4 Tool Table - Create Tool(s)... 5 Tool properties:... 5 Tool Color R/G/B:... 6 Simulation Configurations - create stock... 7 What if plugin is greyed
Flow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
Learning the Pro/ENGINEER Interface
2 Learning the Pro/ENGINEER Interface This chapter introduces the Pro/ENGINEER interface tools: the menus, the dashboards, the selection tools and the viewing controls. As you go through this chapter,
Tail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
FINITE ELEMENT ANALYSIS OF A PLANAR TRUSS
Problem Description: FINITE ELEMENT ANALYSIS OF A PLANAR TRUSS Instructor: Professor James Sherwood Revised: Dimitri Soteropoulos Programs Utilized: Abaqus/CAE 6.11-2 This tutorial explains how to build
Start AxisVM by double-clicking the AxisVM icon in the AxisVM folder, found on the Desktop, or in the Start, Programs Menu.
1. BEAM MODEL Start New Start AxisVM by double-clicking the AxisVM icon in the AxisVM folder, found on the Desktop, or in the Start, Programs Menu. Create a new model with the New Icon. In the dialogue
Obtaining Meshable Surfaces
Chapter 2 Obtaining Meshable Surfaces Exercise 2a: Importing and Repairing CAD Geometry Overview of Exercise Strategy: Import CAD geometry and organize your model using the Assembly Hierarchy. Evaluate
1 Introduction. 2 Install the tool. Millennium 2000 M820 ChessGenius Exclusive, PGN. Version:
1 Introduction We want to improve our ChessGenius Exclusive and make it even better. Therefore, we are always happy to receive your feedback at quality@computerchess.com Currently there are two tools for
Delta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
VERO UK TRAINING MATERIAL. 2D CAM Training
VERO UK TRAINING MATERIAL 2D CAM Training Vcamtech Co., Ltd 1 INTRODUCTION During this exercise, it is assumed that the user has a basic knowledge of the VISI-Series software. OBJECTIVE This tutorial has
Exercise 1a: Interacting With HyperMesh
Exercise 1a: Interacting With HyperMesh This exercise will cover many of the basic concepts that are central to many of the features in HyperMesh. By the end of this exercise you should be familiar with
Getting Started with Alibre CAM. Tutorial 12: Engraving on a Cylinder
Getting Started with Alibre CAM Tutorial 12: Engraving on a Cylinder 344 Introduction This tutorial will illustrate engraving text on a cylinder using a 4 Axis Engraving operation. The stepped instructions
CNC Programming Simplified. EZ-Turn / TurnMill Tutorial.
CNC Programming Simplified EZ-Turn / TurnMill Tutorial www.ezcam.com Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to EZCAM Solutions,
Introduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
Instructor: Clara Knox. Reference:
Instructor: Clara Knox Reference: http://www.smith.edu/tara/cognos/documents/query_studio_users_guide.pdf Reporting tool for creating simple queries and reports in COGNOS 10.1, the web-base reporting solution.
SIMPLE TEXT LAYOUT FOR COREL DRAW. When you start Corel Draw, you will see the following welcome screen.
SIMPLE TEXT LAYOUT FOR COREL DRAW When you start Corel Draw, you will see the following welcome screen. A. Start a new job by left clicking New Graphic. B. Place your mouse cursor over the page width box.
Simulation of Laminar Pipe Flows
Simulation of Laminar Pipe Flows 57:020 Mechanics of Fluids and Transport Processes CFD PRELAB 1 By Timur Dogan, Michael Conger, Maysam Mousaviraad, Tao Xing and Fred Stern IIHR-Hydroscience & Engineering
Job Title: Apply and Edit Modifiers. Objective:
Job No: 06 Duration: 16H Job Title: Apply and Edit Modifiers Objective: To understand that a modifier can be applied to a 2D shape to turn it into a 3D object, and that the modifier s parameters can be
It is desired to analyze the shell-shell intersection shown: 0.01 radius This end fixed Shell-shell intersection dimensions and loading
Problem description It is desired to analyze the shell-shell intersection shown: 0.01 radius Material properties: 0.08 E = 2.07 1011 N/m2 = 0.29 All dimensions in meters Line load of 1000 N/m 0.0075 radius
DOING MORE WITH EXCEL: MICROSOFT OFFICE 2010
DOING MORE WITH EXCEL: MICROSOFT OFFICE 2010 GETTING STARTED PAGE 02 Prerequisites What You Will Learn MORE TASKS IN MICROSOFT EXCEL PAGE 03 Cutting, Copying, and Pasting Data Filling Data Across Columns
Creating a Text Frame. Create a Table and Type Text. Pointer Tool Text Tool Table Tool Word Art Tool
Pointer Tool Text Tool Table Tool Word Art Tool Picture Tool Clipart Tool Creating a Text Frame Select the Text Tool with the Pointer Tool. Position the mouse pointer where you want one corner of the text
TOP Server Client Connectivity Guide for National Instruments' LabVIEW
TOP Server Client Connectivity Guide for National Instruments' LabVIEW 1 Table of Contents 1. Overview and Requirements... 3 2. Setting TOP Server to Interactive Mode... 3 3. Creating a LabVIEW Project...
Fig. 2 Mastercam 2020 Spinning Top SW 19 to MCam20 TOOLPATHS Page 13-1
Mastercam 2020 Chapter 13 Spinning Top SOLIDWORKS 19 to Mastercam 2020 A. Open File in Mastercam 2020. Step 1. If necessary, save your Handle and Flywheel parts file in SOLIDWORKS. Step 2. In Mastercam
Body. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
SOLIDWORKS: Lesson 1 - Basics and Modeling. UCF Engineering
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals UCF Engineering SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment for
Analysis Steps 1. Start Abaqus and choose to create a new model database
Source: Online tutorials for ABAQUS Problem Description The two dimensional bridge structure, which consists of steel T sections (b=0.25, h=0.25, I=0.125, t f =t w =0.05), is simply supported at its lower
TouchKit Touch Panel User manual for Windows9X/ME Version: 3.1.4
TouchKit Touch Panel User manual for Windows9X/ME Version: 3.1.4 TouchKit Touch Panel v3.1.4 0 CONTENT CHAPTER 1. TOUCH PANEL CONTROLLER... 2 1.1 CONTROLLER... 2 1.2 SPECIFICATIONS AND FEATURES... 3 CHAPTER
EXERCISE 2: MODELING MINOAN COLUMNS
Minoan Column at the Palace of Minos, Crete CARLI Digital Collections EXERCISE 2: MODELING MINOAN COLUMNS ASSIGNMENT: In this exercise you will create an architectural element, a Minoan shaped column,
Getting Started with Crazy Talk 6
Getting Started with Crazy Talk 6 Crazy Talk 6 is an application that generates talking characters from an image or photo, as well as facial animation for video. Importing an Image Launch Crazy Talk and
Start VTube-STEP, then follow these steps:
This is a quick-start guide that shows how to perform a basic import of a simple STEP file (the demo 3 part) and then export the data to a bender using the Supravision Network Ethernet protocol. The steps
Mastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
DMU Engineering Analysis Review
Page 1 DMU Engineering Analysis Review Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Inserting a CATAnalysis Document Using DMU Space Analysis From CATAnalysis
AGENDA: Using Gizmos to Modify 3D Models. AutoCAD 3 LECTURE NOTES: CLASS 08. Using Gizmos to Modify 3D Models
AGENDA: Using Gizmos to Modify 3D Models Using Gizmos to Modify 3D Sub-Objects and Faces 3DArray, Mirror3D, and Align Using Gizmos to Modify 3D Models Gizmos allow us to move, rotate, and scale a set of
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc.
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc. 3D Modeling Steps - Sketch Step 1 Sketch Geometry Sketch Geometry Line Sketch Tool 3D Modeling Steps - Constrain Step 1 Sketch Geometry
AutoCAD 2013 Tutorial - Second Level: 3D Modeling
AutoCAD 2013 Tutorial - Second Level: 3D Modeling Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to
Introduction to Computer Aided Engineering: Solidworks and Cosmosworks using CosmosXpress
Introduction to Computer Aided Engineering: Solidworks and Cosmosworks using CosmosXpress Open SolidWorks Tutorial written by Jerry Dutreuil Professor Frank Fisher Stevens Institute of Technology Last