EXPEDITED PERMIT PROCESS FOR RESIDENTIAL SMALL-SCALE PV SYSTEMS STANDARD STRING SYSTEM, MICRO-INVERTER, AC MODULE, OR SUPPLY SIDE

Transcription

1 EXPEDITED PERMIT PROCESS FOR RESIDENTIL SMLL-SCLE P SYSTEMS STNDRD STRIN SYSTEM, MICRO-INERTER, C ULE, OR SUPPLY SIDE Required Information for Permit:. Two copies of site plan showing location of major components on the property. This drawing need not be exactly to scale, but it should represent relative location of components at site. P arrays on dwellings with a perimeter space at ridge and sides may not need separate fire service review.. Two copies of detail, note, elevation, or a combination thereof, indicating P panels installed will be uniformly spaced above the roof surface less than inches from roof surface and the P panels will not extend past roof peak.. Two copies of electrical diagram showing P array configuration, wiring system, overcurrent protection, inverter, disconnects, required signs, and ac connection to building.. Two copies of specification sheets and installation manuals for all manufactured components including, but not limited to, P modules, inverter(s, combiner box, disconnects, and mounting system.. Printed name and signature of person responsible for design on all pages. Include license number if applicable.. Be advised that if any of the P wiring is installed inside the dwelling, smoke alarms will need to be updated if not to current code per Florida Building Code Residential, Section R. Step : Structural Review of P rray Mounting System Is the array to be mounted on a defined, permitted roof structure? Yes No Roof Information:. Does the roof have a single roof covering? Yes No If No, please describe roof covering: _ Mounting System Information:. The mounting structure shall be engineered or a product approval.. Is the roof flat or sloped? Flat Sloped If sloped, at what pitch? Page of Rev. //08

2 . For manufactured mounting systems, fill out information on the mounting system below: a. Mounting System Manufacturer_Product Name and Model# b. Total Weight of P Modules and Rails lbs c. Total Number of ttachment Points d. Weight per ttachment Point (b±c _ lbs e. Maximum Spacing Between ttachment Points on a Rail inches (see product manual for maximum spacing allowed based on maximum design wind speed f. Total Surface rea of P Modules (square feet ft g. Distributed Weight of P Module on Roof (b±f _ lbs/ft Step : Three-Day Plan Review of P System In order for a P system to be considered for an expedited permit process, the following must apply:. P modules, utility-interactive inverters, and combiner boxes are identified for use in P systems.. The P array is composed of series strings or less per inverter.. The total inverter capacity has a continuous ac power output of 0,000 Watts or less.. One of the standard electrical diagrams can be used to accurately represent the P system.. The P system, when installed on a historic property, is not located on a character defining feature and is not visible from the street.. The P system extends no further than above mounting surface, and is uniformly spaced above a sloped roof surface. 7. The P system does not extend past the roof peak. Step : Separate Permits Required Per the Florida dministrative Code, Rule -.0, Solar contractors may install new or replace existing power and control wiring in photovoltaic (P source circuits, P output circuits, battery storage system circuits, and power conditioning unit. In an interactive system that operates parallel with a primary source of electrical energy, this work is limited to the P supply side of the power conditioning unit. In a stand-alone, or non-grid connected system, the work above-referenced shall be limited to the P supply side of the power conditioning unit and shall not include wiring integral to the building premises. ll work shall be done in accordance with the National Electric Code. ny work integral to the building premises wiring shall be done by a licensed electrical contractor. separate electrical permit will be required for this work, and should be submitted at the same time as the permit application for the P system. Print Name: _ Company Name (if applicable: Signature: License Number (if applicable: Date: Page of Rev. //08

3 EXPEDITED PERMITTIN CHECKLIST FOR RESIDENTIL PHOTOOLTIC SYSTEMS: ROOFTOP MOUNTED Required Paperwork Checklist: This Document Permit pplication with Notice of Commencement for the installation. Separate Electrical permit application if applicable. Small scale P system package with supporting documentation, drawings, and specifications. ❶ Project Information: Project pplicant: Site Owner Name: Project ddress: P system description: ❷ Project Requirements P system is designed and proposed for a detached single family house. P system is designed for rooftop of a house in general compliance with applicable codes. Mounting system is engineered and designed for P. Panels are mounted no higher than above the surface of the roof and are uniformly spaced above the roof surface. No portion of the system exceeds the peak off the roof. If located on a historic property, does the installation comply with the City s historic preservation regulations? Whenever possible, equipment such as solar panels should not be affixed to the building, but sited in the rear or side yard locations and fully screened with landscaping, fence orr wall. When placement upon the building is unavoidable, such equipment shall be located on a non character defining elevation or roof slope that is not visible from the street. In no instance, shall the equipment be allowed to be placed upon any character defining feature. (see beach.org/departments/historic_preservation Method and type of weatherproofing roof penetrations aree provided. Home is code compliant to setbacks and height, or code allows expansion of nonconformity for solar panels. If all above criteria are met, please proceed to determine if project qualifies for an expedited permit. Page of Rev. //08

4 ❸Determine if your project qualifies for an expedited permit ( day turnaround. Solar and Electrical contractors can apply for an expedited permit where the P system meets the requirements listed in this Checklist and use a template electrical diagram provided by the City. ll project plans and supporting documentation must be provided on site for the inspector. Project will be subject to a field inspection. Yes No N/ a P modules, utility interactive inverters, and combiner boxes are identified and listed and labeled for location and use in P systems. b The system meets all current FBC, City, and Electrical Code requirements. c For Split Buss panels the C interconnection must be one of the six service disconnects. d Maximum load added to the panelboard is based on the rating of the P system and is limited to 0,000 watts. e I have attached the following Electrical Template and Site Plan: Electrical Diagram Standard Strings / Standard String with Converter Electrical Diagram Micro Inverter Electrical Diagram C Module Electrical Diagram Supply Side None of the above Electrical Permit with Plan Review Required Comments: If you answered yes to all of the above questions (yes or N/ for item c, and are using a template diagram provided by the City or followed the template and provided a signed and sealed drawing, your project qualifies for an expedited permit. ❹ Submit this Checklist, the Building and Electrical (if applicable Permit pplications with notarized signature, and copies of the Template Electrical Drawing and Site Plan to: Permit Processing, Development Services Dept., 00 E Boynton Beach Blvd., Boynton Beach, FL I attest that all information in this checklist is accurate to the best of my knowledge. pplicant Signature: Date: pplicant Name (Please Print: License Number (if applicable: Electrical Contractor and electrical permit required for all building premises wiring per Florida dministrative Code, Rule.0 and FBC 0. Page of Rev. //08

5 Site Plan Solar merica Board for Codes and Standards Report

6 Standard Electrical Diagram Expedited Permit Process for P Systems

7 Notes for Standard Electrical Diagram SINS SEE UIDE SECTION 7 P ULE STC (uide Section ULE MKE ULE EL MX POWER-POINT CURRENT (I MP MX POWER-POINT OLTE ( MP OPEN-CIRCUIT OLTE ( OC SHORT-CIRCUIT CURRENT (I SC MX SERIES FUSE (OCPD NOTES FOR LL DRWINS: OCPD = OERCURRENT PROTECTION DEICE NTIONL ELECTRICL CODE REFERENCES SHOWN S (NEC XXX.XX INERTER RTINS (uide Section INERTER MKE INERTER EL MX OLT RTIN SIN FOR DISCONNECT PHOTOOLTIC POWER SOURCE RTED MPP CURRENT RTED MPP OLTE MX SYSTEM OLTE MX CIRCUIT CURRENT WRNIN: ELECTRICL SHOCK HZRD LINE ND LOD MY BE ENERIZED IN OPEN POSITION MXIMUM POWER (P MX MX OLTE (TYP 00 OC TEMP COEFF (m/ o C or %/ o C IF COEFF SUPPLIED, CIRCLE UNITS W MX 0 o C NOMINL C OLTE MX C CURRENT MX OCPD RTIN W SIN FOR INERTER OCPD ND C DISCONNECT (IF USED SOLR P SYSTEM C POINT OF CONNECTION C OUTPUT CURRENT NOMINL C OLTE THIS PNEL FED BY MULTIPLE SOURCES (UTILITY ND SOLR NOTES FOR RRY CIRCUIT WIRIN (uide Section and 8 and ppendix D: NOTES FOR INERTER CIRCUITS (uide Section 8 and 9:. LOWEST EXPECT MBIENT TEMPERTURE BSED ON SHRE MINIMUM MEN EXTREME DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. LOWEST EXPECTED MBIENT TEMP o C IF UTILITY REQUIRES ISIBLE-BREK SWITCH, DOES THIS SWITCH MEET THE REQUIREMENT? YES NO N/. HIHEST CONTINUOUS MBIENT TEMPERTURE BSED ON SHRE HIHEST MONTH % DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. HIHEST CONTINUOUS TEMPERTURE _ o C. 00 SHRE FUNDEMENTLS % DESIN TEMPERTURES DO NOT EXCEED 7 o C IN THE UNITED STTES (PLM SPRINS, C IS. o C. FOR LESS THN 9 CURRENT-CRRYIN CONDUCTORS IN ROOF-MOUNTED SUNLIT CONDUIT T LEST 0." BOE ROOF ND USIN THE OUTDOOR DESIN TEMPERTURE OF 7 o C OR LESS (LL OF UNITED STTES, a W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 7.8 MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. b 0 W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 9. MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. IF ENERTION METER REQUIRED, DOES THIS METER SOCKET MEET THE REQUIREMENT? YES NO N/ SIZE PHOTOOLTIC POWER SOURCE ( CONDUCTORS BSED ON MX CURRENT ON NEC 90. SIN OR OCPD RTIN T DISCONNECT SIZE INERTER OUTPUT CIRCUIT (C CONDUCTORS CCORDIN TO INERTER OCPD MPERE RTIN. (See uide Section 9 TOTL OF INERTER OCPD(s, ONE FOR ECH INERTER. DOES TOTL SUPPLY BREKERS COMPLY WITH 0% BUSBR EXCEPTION IN 90.(B((a? YES NO ddress and Phone: Notes for One-Line Standard Electrical Diagram for Single-Phase P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE E. SCLE NTS Date: SHEET Solar merica Board for Codes and Standards Report

8 T 7 8 T Micro-Inverter Electrical Diagram EQUIPMENT SCHEDULE DESCRIPTION P or C ULE /C INERTER (MICRO J-BOX (IF USED P RRY C COMB. PNEL (IF USED EN METER (IF USED C DISCONNECT (IF USED SERICE PNEL PRT NUMBER NOTES UTILITY SERICE M C C _ MICRO-INERTERS IN BRNCH- CIRCUIT SEE UIDE PPENDIX D FOR INFORMTION ON ULE ND RRY ROUNDIN C J-BOX M 7 C DISCO 8 MIN OCPD INERTER OCPD C MICRO-INERTERS IN BRNCH- CIRCUIT C C C COMBINER PNEL BUILDIN ROUNDIN ELECTRODE MIN SERICE PNEL FOR UNUSED ULES PUT "N/ in BLNK BOE CONDUIT ND CONDUCTOR SCHEDULE DESCRIPTION OR CONDUCTOR TYPE USE- or P WIRE EC EC X LL THT PPLY EXTERIOR CBLE LISTED W/ IN. THWN- or XHHW- or RHW- EC EC X LL THT PPLY NO EC IF 90. SYSTEM THWN- or XHHW- or RHW- EC EC X LL THT PPLY COND. UE MF MF NUMBER OF CONDUCTORS MF Cable MF Cable CONDUIT TYPE N/ N/ N/ SME SME CONDUIT SIZE N/ N/ N/ SME SME ddress and Phone: One-Line Standard Electrical Diagram for Micro-Inverter P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE SCLE NTS Date: SHEET E.a 0 Expedited Permit Process for P Systems

9 Notes for Micro-Inverter Electrical Diagram SINS SEE UIDE SECTION 7 P ULE STC (uide Section ULE MKE ULE EL NOTES FOR LL DRWINS: OCPD = OERCURRENT PROTECTION DEICE NTIONL ELECTRICL CODE REFERENCES SHOWN S (NEC XXX.XX SIN FOR DISCONNECT No sign necessary since 90. marking on P module covers needed information MX POWER-POINT CURRENT (IMP MX POWER-POINT OLTE (MP OPEN-CIRCUIT OLTE (OC SHORT-CIRCUIT CURRENT (ISC MX SERIES FUSE (OCPD MXIMUM POWER (PMX MX OLTE (TYP 00 OC TEMP COEFF (m/ o C or %/ o C INERTER RTINS (uide Section INERTER MKE INERTER EL MX OLT RTIN MX 0 o C NOMINL C OLTE MX C CURRENT SIN FOR INERTER OCPD ND C DISCONNECT (IF USED SOLR P SYSTEM C POINT OF CONNECTION C OUTPUT CURRENT NOMINL C OLTE THIS PNEL FED BY MULTIPLE SOURCES (UTILITY ND SOLR IF COEFF SUPPLIED, CIRCLE UNITS MX OCPD RTIN NOTES FOR RRY CIRCUIT WIRIN (uide Section and 8 and ppendix E: NOTES FOR INERTER CIRCUITS (uide Section 8 and 9:. LOWEST EXPECT MBIENT TEMPERTURE BSED ON SHRE MINIMUM MEN EXTREME DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. LOWEST EXPECTED MBIENT TEMP o C IF UTILITY REQUIRES ISIBLE-BREK SWITCH, DOES THIS SWITCH MEET THE REQUIREMENT? YES NO N/. HIHEST CONTINUOUS MBIENT TEMPERTURE BSED ON SHRE HIHEST MONTH % DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. HIHEST CONTINUOUS TEMPERTURE o C. 009 SHRE FUNDMENTLS % DESIN TEMPERTURES DO NOT EXCEED 7 o C IN THE UNITED STTES (PLM SPRINS, C IS. o C. FOR LESS THN 9 CURRENT-CRRYIN CONDUCTORS IN ROOF-MOUNTED SUNLIT CONDUIT T LEST 0." BOE ROOF ND USIN THE OUTDOOR DESIN TEMPERTURE OF 7 o C OR LESS (LL OF UNITED STTES, a W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 7.8 MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. b 0 W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 9. MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. IF ENERTION METER REQUIRED, DOES THIS METER SOCKET MEET THE REQUIREMENT? YES NO N/ SIZE PHOTOOLTIC POWER SOURCE ( CONDUCTORS BSED ON MX CURRENT ON NEC 90. SIN OR OCPD RTIN T DISCONNECT SIZE INERTER OUTPUT CIRCUIT (C CONDUCTORS CCORDIN TO INERTER OCPD MPERE RTIN. (See uide Section 9 TOTL OF INERTER OUTPUT CIRCUIT OCPD(s, ONE FOR ECH MICRO- INERTER CIRCUIT. DOES TOTL SUPPLY BREKERS COMPLY WITH 0% BUSBR EXCEPTION IN 90.(B((a? YES NO ddress and Phone: Notes for One-Line Standard Electrical Diagram for Single-Phase P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE E.a SCLE NTS Date: SHEET Solar merica Board for Codes and Standards Report 7

10 T 7 T C Module Electrical Diagram EQUIPMENT SCHEDULE DESCRIPTION PRT NUMBER NOTES UTILITY SERICE M C C C ULES IN BRNCH- CIRCUIT C SEE UIDE PPENDIX D FOR INFORMTION ON ULE ND RRY ROUNDIN J-BOX M C DISCO 7 MIN OCPD INERTER OCPD C C C ULES IN BRNCH- CIRCUIT C C COMBINER PNEL BUILDIN ROUNDIN ELECTRODE MIN SERICE PNEL FOR UNUSED C ULES PUT "N/ in BLNK BOE CONDUIT ND CONDUCTOR SCHEDULE DESCRIPTION OR CONDUCTOR TYPE USE- or P WIRE EC EC X LL THT PPLY EXTERIOR CBLE LISTED W/ IN. THWN- or XHHW- or RHW- EC EC X LL THT PPLY NO EC IF 90. SYSTEM THWN- or XHHW- or RHW- EC EC X LL THT PPLY COND. UE MF MF NUMBER OF CONDUCTORS MF Cable MF Cable CONDUIT TYPE N/ N/ N/ CONDUIT SIZE N/ N/ N/ ddress and Phone: One-Line Standard Electrical Diagram for C Module P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE E.b SCLE NTS Date: SHEET 8 Expedited Permit Process for P Systems

11 Notes for C Module Electrical Diagram SINS SEE UIDE SECTION 7 NOTES FOR LL DRWINS: SIN FOR DISCONNECT OCPD = OERCURRENT PROTECTION DEICE NTIONL ELECTRICL CODE REFERENCES SHOWN S (NEC XXX.XX N/ since no dc wiring C ULE RTINS (uide ppendix C C ULE MKE C ULE EL NOMINL OPERTIN C OLTE NOMINL OPERTIN C FREQUENCY MXIMUM C POWER MXIMUM C CURRENT SIN FOR INERTER OCPD ND C DISCONNECT (IF USED SOLR P SYSTEM C POINT OF CONNECTION C OUTPUT CURRENT NOMINL C OLTE THIS PNEL FED BY MULTIPLE SOURCES (UTILITY ND SOLR MXIMUM OCPD RTIN NOTES FOR RRY CIRCUIT WIRIN (uide Section and 8 and ppendix F: NOTES FOR INERTER CIRCUITS (uide Section 8 and 9:. LOWEST EXPECT MBIENT TEMPERTURE BSED ON SHRE MINIMUM MEN EXTREME DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. LOWEST EXPECTED MBIENT TEMP o C IF UTILITY REQUIRES ISIBLE-BREK SWITCH, DOES THIS SWITCH MEET THE REQUIREMENT? YES NO N/. HIHEST CONTINUOUS MBIENT TEMPERTURE BSED ON SHRE HIHEST MONTH % DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. HIHEST CONTINUOUS TEMPERTURE o C. 009 SHRE FUNDMENTLS % DESIN TEMPERTURES DO NOT EXCEED 7 o C IN THE UNITED STTES (PLM SPRINS, C IS. o C. FOR OR LESS CURRENT-CRRYIN CONDUCTORS IN ROOF-MOUNTED SUNLIT CONDUIT T LEST 0." BOE ROOF ND USIN THE OUTDOOR DESIN TEMPERTURE OF 7 o C OR LESS (LL OF UNITED STTES, a W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR C ULES INERTER OUTPUT CIRCUITS WITH MPS OR LESS WHEN PROTECTED BY - MP OR SMLLER OCPD. IF ENERTION METER REQUIRED, DOES THIS METER SOCKET MEET THE REQUIREMENT? YES NO N/ SIZE PHOTOOLTIC POWER SOURCE ( CONDUCTORS BSED ON MX CURRENT ON NEC 90. SIN OR OCPD RTIN T DISCONNECT (N/ SIZE INERTER OUTPUT CIRCUIT (C CONDUCTORS CCORDIN TO INERTER OCPD MPERE RTIN. (See uide Section 9 TOTL OF INERTER OUTPUT CIRCUIT OCPD(s, ONE FOR ECH C ULE CIRCUIT. DOES TOTL SUPPLY BREKERS COMPLY WITH 0% BUSBR EXCEPTION IN 90.(B((a? YES NO b 0 W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR C ULES INERTER OUTPUT CIRCUITS WITH MPS OR LESS WHEN PROTECTED BY 0- MP OR SMLLER OCPD. ddress and Phone: Bill Notes for One-Line Standard Electrical Diagram for Single-Phase P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE E.b 0 Ted SCLE NTS Date: SHEET Solar merica Board for Codes and Standards Report 9

12 Supply-Side Connected Electrical Diagram EQUIPMENT SCHEDULE T DESCRIPTION PRT NUMBER NOTES 9 0 UTILITY SERICE M 7 8 _ ULES IN SERIES SOURCE-CIRCUIT ULES IN SERIES SOURCE-CIRCUIT ULES IN SERIES SOURCE-CIRCUIT J-BOX COMBINER DISCO INERTER C C DISCO M MIN OCPD MIN SERICE PNEL ULES IN SERIES SOURCE-CIRCUIT FOR UNUSED SERIES STRINS PUT "N/ in BLNK BOE SEE UIDE PPENDIX C FOR INFORMTION ON ULE ND RRY ROUNDIN CONDUIT ND CONDUCTOR SCHEDULE Disregard if provided with inverter BUILDIN ROUNDIN ELECTRODE T DESCRIPTION OR CONDUCTOR TYPE USE- or P WIRE BRE COPPER EQ. RD. COND. (EC THWN- or XHHW- or RHW- THWN- or XHHW- or RHW- INSULTED EC ROUNDIN ELECTRODE COND. THWN- or XHHW- or RHW- INSULTED EC THWN- or XHHW- or RHW- COND. UE NUMBER OF CONDUCTORS CONDUIT TYPE CONDUIT SIZE ddress and Phone: One-Line Electrical Diagram for Supply-Side Connected Single-Phase P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE SCLE NTS Date: SHEET E.c 0 0 Expedited Permit Process for P Systems

13 Notes for Supply-Side Connected Electrical Diagram SINS SEE UIDE SECTION 7 P ULE STC (uide Section ULE MKE ULE EL MX POWER-POINT CURRENT (I MP MX POWER-POINT OLTE ( MP OPEN-CIRCUIT OLTE ( OC SHORT-CIRCUIT CURRENT (I SC MX SERIES FUSE (OCPD NOTES FOR LL DRWINS: OCPD = OERCURRENT PROTECTION DEICE NTIONL ELECTRICL CODE REFERENCES SHOWN S (NEC XXX.XX INERTER RTINS (uide Section INERTER MKE INERTER EL MX OLT RTIN SIN FOR DISCONNECT PHOTOOLTIC POWER SOURCE RTED MPP CURRENT RTED MPP OLTE MX SYSTEM OLTE MX CIRCUIT CURRENT WRNIN: ELECTRICL SHOCK HZRD LINE ND LOD MY BE ENERIZED IN OPEN POSITION MXIMUM POWER (P MX MX OLTE (TYP 00 OC TEMP COEFF (m/ o C or %/ o C IF COEFF SUPPLIED, CIRCLE UNITS W MX 0 o C NOMINL C OLTE MX C CURRENT MX OCPD RTIN W SIN FOR INERTER OCPD ND C DISCONNECT (IF USED SOLR P SYSTEM C POINT OF CONNECTION C OUTPUT CURRENT NOMINL C OLTE THIS PNEL FED BY MULTIPLE SOURCES (UTILITY ND SOLR NOTES FOR RRY CIRCUIT WIRIN (uide Section and 8 and ppendix D: NOTES FOR INERTER CIRCUITS (uide Section 8 and 9:. LOWEST EXPECT MBIENT TEMPERTURE BSED ON SHRE MINIMUM MEN EXTREME DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. LOWEST EXPECTED MBIENT TEMP o C IF UTILITY REQUIRES ISIBLE-BREK SWITCH, DOES THIS SWITCH MEET THE REQUIREMENT? YES NO N/. HIHEST CONTINUOUS MBIENT TEMPERTURE BSED ON SHRE HIHEST MONTH % DRY BULB TEMPERTURE FOR SHRE LOCTION MOST SIMILR TO INSTLLTION LOCTION. HIHEST CONTINUOUS TEMPERTURE _ o C. 00 SHRE FUNDEMENTLS % DESIN TEMPERTURES DO NOT EXCEED 7 o C IN THE UNITED STTES (PLM SPRINS, C IS. o C. FOR LESS THN 9 CURRENT-CRRYIN CONDUCTORS IN ROOF-MOUNTED SUNLIT CONDUIT T LEST 0." BOE ROOF ND USIN THE OUTDOOR DESIN TEMPERTURE OF 7 o C OR LESS (LL OF UNITED STTES, a W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 7.8 MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. b 0 W, 90 o C CONDUCTORS RE ENERLLY CCEPTBLE FOR ULES WITH Isc OF 9. MPS OR LESS WHEN PROTECTED BY -MP OR SMLLER FUSE. IF ENERTION METER REQUIRED, DOES THIS METER SOCKET MEET THE REQUIREMENT? YES NO N/ SIZE PHOTOOLTIC POWER SOURCE ( CONDUCTORS BSED ON MX CURRENT ON NEC 90. SIN OR OCPD RTIN T DISCONNECT SIZE INERTER OUTPUT CIRCUIT (C CONDUCTORS CCORDIN TO INERTER OCPD MPERE RTIN. (See uide Section 9 TOTL OF INERTER OCPD(s, ONE FOR ECH INERTER. DOES TOTL SUPPLY BREKERS COMPLY WITH 0% BUSBR EXCEPTION IN 90.(B((a? YES NO ddress and Phone: Notes for One-Line Standard Electrical Diagram for Single-Phase P Systems Site Name: Site ddress: System C Size: SIZE FSCM NO DW NO RE E. SCLE NTS Date: SHEET Solar merica Board for Codes and Standards Report