MINI-BEAM SM2A312F. MINI-BEAM Glass Fiber Optic. Output Type E X C E S S G A I N m.033 ft. SPST Solid-state 2-wire E X C E S S G A I N

Transcription

1 MINI-BAM elf-contained AC-operated ensors for use with Banner Glass Fiber Optics Compact, modulated, self-contained infrared fiber optic sensors for 24-24V ac 2-wire operation Useable in opposed, retroreflective, and diffuse fiberoptic modes with Banner glass fiber optic assemblies witch-selectable for light operate or dark operate 8 millisecond response PT CR solid-state output switches up to 3 ma; low leakage current and saturation voltage Rugged, epoxy-encapsulated construction: meets NMA standards 1, 2, 3, 3, 4, 4X, 12 and 13; IC IP67 Models Range Cable MINI-BAM Glass Fiber Optic upply Voltage Output Type xcess Gain Beam Pattern Infrared, 88 nm Diffuse mode performance based on 9% reflectance white test card QD Range varies by sensing mode and fiber optics used 2 m (6.5 ft) 3-Pin Micro QD 24-24V ac PT olid-state 2-wire X C G A I N X C G A I N m.33 ft mm.4 in IT13 Fibers BT13 Fiber.1 m.33 ft IT23 Fibers DITANC BT23 Fiber 1 mm.4 in DITANC Opposed Mode Glass Fibers IT23 Fibers w/l9 lenses 1 m 3.3 ft Diffuse Mode Glass Fibers 1 mm 4 in 1 m 33 ft 1 mm 4 in 75 mm 5 mm 25 mm 25 mm 5 mm 75 mm 1.9 mm 1.3 mm.65 mm.65 mm 1.3 mm 1.9 mm Opposed Mode IT13 1 mm 4 in BT13 2 mm 8 in Diffuse Mode 3 mm 12 in DITANC IT23 4 mm 16 in 7.5 mm 15 mm 2 3 mm.3 in.6 in.9 in 1.2 in DITANC BT23 3 in 2 in 1 in 1 in 2 in 3 in 5 mm 2 in 37.5 mm 1.5 in.75 in.5 in.25 in.25 in.5 in.75 in For tandard MINI-BAMs: i) 9 m (3 ft) cables are available by adding suffix W/3 to the model number of any cabled sensor (e.g. - W/3). ii) A 15 mm (6 in.) long pigtail cable with attached QD connector is available by adding suffix QDP to the model number of any MINI-BAM sensor (e.g. - QDP). ee page 5 for more information. iii) A model with a QD connector requires an accessory mating cable. ee page 5 for more information.

2 MINI-BAM Features * Note regarding Light/Dark operate switch: Turn switch fully clockwise for light operate (sensor outputs conduct when sensing light is received) Turn switch fully counterclockwise for dark operate (sensor outputs conduct when sensing light is not received) 15 Turn Gain Adjustment and Light/Dark Operate witch* Gasketed Acrylic Cover Red LD Lights when the sensor's output is conducting MINI-BAM Fiber Information 1) Install the O-ring (supplied with the fiber) on each fiber end, as shown in the drawing. 2) While pressing the fiber ends firmly into the ports on the front of the sensor, slide the U-shaped retaining clip (supplied with the sensor) into the slot in the sensor s barrel, until it snaps into place. Retaining Clip O-ring Lens Attachment Lenses are sometimes added to fiber optic assemblies for extending opposed mode sensing range. Banner ofers the following lens assemblies for use with fiber optic assemblies which have 5/16-24 threaded sensing tips (e.g. fiber model IT23): Model Lens ize Focal Length Housing Notes L9 1 (1/2 ) 1 (1/2 ) Aluminum uitable for all but highly corrosive environments Maximum operating temperature is 1º C (212º F) uitable for all but highly corrosive environments nd of Fiber Optic Bundle Lens Housing L16F 25 mm (1 ) 44 mm (1.7 ) Delrin L16FAL 25 mm (1 ) 44 mm (1.7 ) Aluminum Lens Focus Focal Length of Lens Illuminate Opposite nd 5/16" Threaded ensing Tip L16F 25 mm (1 ) 44 mm (1.7 ) tainless teel uitable for all environments Lenses are most efficient when they are located slightly beyond their focal length distance from the sensing end of the fiber optic bundle. The easiest way to focus a lens is to treat it like a magnifying glass. Illuminate the fiber optic bundle at the threaded end of the fiber optic assembly by directing the opposite end toward a visible light source (e.g. - an incandenscent bulb, visible LD, sunlight, etc.). Thread the lens onto the fiber optic assembly until the end of the fiber optic bundle comes into sharp focus under the lens. Then, back off (unthread) the lens assembly from the point of sharpest focus by one to three full turns. The illuminated bundle should now appear slightly blurred. This is the optimum setting, and the lens may be secured in position using one of the jam nuts provided. Refer to the drawing above. page 2

3 MINI-BAM AC Product pecifications upply Voltage and Current upply Protection Circuitry Output Configuration Output Rating Output Protection Circuitry Output Response Time Repeatability Adjustments Indicators Construction nvironmental Rating Connections Operating Temperature 24 to 24V ac (5/6 Hz), 25V ac max Protected against transient voltages PT CR solid-state relay with either normally closed or normally open contact (light/dark operate selectable); 2-wire hookup Minimum load current 5 ma; maximum steady-state load capability 3 ma to 5 C ambient (122 F) 1 ma to 7 C ambient (158 F) Inrush capability 3 amps for 1 second (non repetitive); 1 amps for 1 cycle (non repetitive) Off-state leakage current less than 1.7 ma rms On-state voltage drop 5 volts at 3 ma load, 1 volts at 15 ma load Protected against false pulse on power-up 8 milliseconds on and off OFF response time specification does not include load response of up to 1 /2 ac cycle (8.3 milliseconds). Response time specification of load should be considered when important. (NOT: 3 millisecond delay on power-up.) 2.6 milliseconds; Response time and repeatability specifications are independent of signal strength. LIGHT/DARK OPRAT select switch, and 15-turn slotted brass screw GAIN (sensitivity) adjustment potentiometer (clutched at both ends of travel). Both controls are located on rear panel of sensor and protected by a gasketed, clear acrylic cover. Red indicator LD on rear of sensor is ON when the load is energized Reinforced VALOX housing, totally encapsulated, o-ring sealing, acrylic lenses, and stainless steel screws Meets NMA standards 1, 2, 3, 3, 4, 4X, 12, and 13; IC IP67 PVC-jacketed 2-conductor 2 m (6.5ft) or 9 m (3ft) cables, or 3-pin micro-style quick disconnect (QD) fitting are available. QD cables are ordered separately. ee page 5. Temperature: -2 to +7 C (-4 to +158 F) Maximum Relative Humidity: 9% at 5 C (non-condensing) Application Notes i) ac MINI-BAMs may be destroyed from overload conditions ii) Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state voltage of the sensor will interfere with proper operation of the load iii) The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in series or parallel with mechanical switch contacts Certifications VALOX is a registered trademark of General lectric Company page 3

4 MINI-BAM AC Hookup Diagrams AC ensors with Attached Cable AC ensors with Quick Disconnect (3-Pin Micro-tyle) bn bu Load 24-24V ac rd/bk rd/wh gn Load 24-24V ac Red/White 3-Pin Micro-tyle Pin-out (Cable Connector hown) Green Red/Black Quick Disconnect (QD) Option AC MINI-BAM sensors are sold with either a 2 m (6.5 ft) or a 9 m (3 ft) attached PVC-covered cable, or with a 3-pin micro-style QD cable fitting. AC QD sensors are identified by the letters QD in their model number suffix. For more information on mating QD cables, see page 5. MINI-BAM Dimension Information MINI-BAM AC ensor with Integral Cable MINI-BAM AC ensor with Quick-Disconnect 3.7 mm (1.21 in) 3.2 mm (.13 in) 12.2 mm (.48 in) ø 3 mm Clearance (2) 1/2-2 UNF Thread Quick Disconnect 24.1 mm (.95 in) M18 x 1 x 19 mm Thread (Mounting Nut upplied) 2 m (6.5 ft) Cable Mounting Peg (ø 6.3 mm x ) 19.1 mm (.75 in) Fiber Optic Fitting 89. mm (3.5 in) 69.9 mm (2.75 in) 31.2 mm (1.23 in) page 4

5 Model uffix Modification MINI-BAM MODIFICATION Description xample of Model Number All MINI-BAM sensors may be ordered with an integral 9 m (3 ft) W/3 9 meter (3 ft) cable W/3 cable in place of the standard 2 m (6.5 ft) cable QDP Pigtail Quick Disconnect All MINI-BAMs may be built with a 15 mm (6 in) long integral cable which is terminated with the appropriate QD connector. QDP xtension Cables (without connectors) The following cables are available for extending the length of existing sensor cable. These are 3 m (1 ft) lengths of MINI-BAM cable. This cable may be spliced to existing cable. Connectors, if used, must be customer-supplied. Model Type Used with: C312A-1 2-conductor All MINI-BAM M2A312 ac models Micro-tyle Quick Disconnect Cables Cable: PVC jacket, polyurethane connector body, nickel-plated brass coupling nut Conductors: 22 or 2 AWG high-flex stranded, PVC insulation, gold-plated contacts Temperature: -4 to +8 C (-4 to +176 F) Voltage Rating: 25V ac/3v dc (3-pin), 125V ac/15v dc (4-pin) tyle Model Length Dimensions Pin-out 3-Pin traight MQDC-36 MQDC-315 MQDC-33 2 m (6.5 ft) ø15 mm 5 m (15 ft) 9 m (3 ft) ø1/2-2unf-2b 44 mm max. (1.7 in) Green 38 mm max. (1.5 in) Red/White Red/Black 3-Pin Right-angle MQDC-36RA MQDC-315RA MQDC-33RA 2 m (6.5 ft) 5 m (15 ft) 9 m (3 ft) 38 mm max. (1.5 in) 1/2-2UNF-2B ø15 mm page 5

6 Mounting Brackets Model Description R 5.1 mm (.2 in) R 24.1 mm (.95 in) 1 (TYP) MB312 tainless steel 2-axis, side mounting bracket 2 ø 3.5 mm (.12 in) 15 (2) C 31.8 mm L (1.25 in) ø 3.5 mm lot (.12 in) 4.32 mm (.17 in) lot (2) 2.3 mm (.8 in) R 3.1 mm (.12 in) (2) mm (.79 in) (.1 in) 45.5 mm (1.79 in) R 5.1 mm (.2 in) R 24.1 mm (.95 in) 15.2 mm (.6 in) 15 (2) C 31.8 mm L (1.25 in) MB312PD tainless steel 18 mm barrelmounting bracket 2 ø 4. (.18 in) 9 ø 4. lot (.18 in) 4. (1.6 in) R 3.1 mm (.12 in) (2) mm (.725 in) (.1 in) 45.5 mm (1.79 in) 4.3 mm lot (2) (.17 in) 9 1 (2) 1 (2) 24.1 mm (.95 in) 9.1 mm (.36 in) MB312B tainless steel 2-axis, bottom mounting bracket Includes MB12F (below) (.1 in) 3.1 mm lot (2) (.12 in) 17.3 mm (2) (.68 in) 8. (2) (.34 in) ø 6.9 mm (.27 in) 35. mm (2) (1.38 in) 5.8 mm (2. in) 23.4 mm 11.4 mm (.92 in) (.45 in) MB46L L bracket 14 ga 316 stainless steel (.2 in) (.2 in) 5 mm (.2 in) (2x) 8 mm (.3 in) CL 1 15 mm ø3 (1.4 in) ø6.5 mm (.26 in) (6x) 65 mm (2.6 in) 54 mm (2.1 in) 2 mm (.1 in) 27 mm (1.1 in) page 6

7 Mounting Brackets Model Description Dimensions MB46 bracket 14 ga 316 stainless steel 1 mm (.4 in) (.2 in) (.2 in) 5 mm (.2 in) (4x) 8 mm (.3 in) CL 34 mm (1.3 in) 1 17 mm (.7 in) 15 mm 3.5 mm (.14 in) ø3 (1.4 in) ø6.5 mm (.26 in) (6x) 65 mm (2.6 in) 54 mm (2.1 in) 2 mm (.1 in) 27 mm (1.1 in) 1 34 mm (1.3 in) 17 mm (.7 in) C L MB46U U bracket 14 ga 316 stainless steel 13 mm (.5 in) (.2 in) (.2 in) 5 mm (.2 in) (4x) 8 mm (.3 in) mm (.14 in) 15 mm ø3 (1.4 in) ø6.5 mm (.26 in) (6x) 1 65 mm (2.6 in) 54 mm (2.1 in) 2 mm (.1 in) 27 mm (1.1 in) 7 mm (2.8 in) MB18C 18 mm split clamp black VALOX bracket tainless steel mounting hardware included 14. mm (.55 in) 42.4 mm (1.67 in) 4. mm (1.6 in) 3. mm (1.18 in) 21.1 mm (.83 in) (.1 in) 13 mm (.5 in) Nut Plate M5 x.8 x crew (2) MB18 18 mm swivel, black VALOX bracket tainless steel mounting hardware included 44.5 mm (1.75 in) 13. mm (.5 in) 46. mm (1.81 in) 36. mm (1.42 in) 25.4 mm (1. in) (.1 in) 1.9 mm (.43 in) pacer (If Required) Nut Plate M5 x.8 x crew (2) 6.4 mm (.25 in) page 7