KEYCREATOR 3D Direct Modeling Software
|
|
- Martin Richards
- 6 years ago
- Views:
Transcription
1 KeyCreator Lesson KC5107 Graft The Graft Function is a powerful partner to the Prune Function that we used earlier. You will typically use the Graft Function immediately after performing a pruning operation on a feature or features. While the results obtained by using the Graft Function can also be realized with a combination of traditional Xform and Boolean Operations, the compact execution provided by grafting makes mastering this tool well worth the effort. In this lesson, we ll prune a pattern of six cutouts on the horizontal leg of the L-shaped solid and then use the Graft Function to transfer these tool bodies to the vertical leg where we will reposition them and create new cutouts. We ll start with a new file in View 1. (The Top View.) Click on the CREATE BLOCK Icon. A Dialog Box appears. We ll use the Keyin Option. Type 8 for the Width and Length and 9 for the Height. Hit the ENTER Key. Using the Cursor Option, click anywhere on the screen to place the block. KUBOTEK Freedom and Precision 1
2 Switch to the Isometric View. (View 7.) Now, click on the CONSTANT RADIUS BLEND Icon. Type 2 for the Radius and select the bottom, rear edge of the block. Hit the ENTER Key. Your part should look like this: Click on the SHELL Icon. A Dialog Box appears. Type 0.15 for the shell thickness and hit the ENTER Key. Select the top face, front face, right face, and hidden left face of the part. (Use the SPACEBAR or TAB Key to select the hidden face.) KUBOTEK Freedom and Precision 2
3 Your part should now look like this: Now, establish a construction plane on the broad, top horizontal surface of the part. Select a new construction color. Click on the CREATE ROUNDED RECTANGLE BY WIDTH HEIGHT Icon. Type for the corner radius. Click on the MidCtr Anchor Option. Type 1 for the Width and Height. Click on the Offset Option and using the EndEnt Option, click on the top, front, left corner of the part to establish the offset reference position. Type 1 for dxc and 1 for dyc. The dzc value is zero. You will now have a rounded rectangular profile on the top surface of the part. KUBOTEK Freedom and Precision 3
4 Click on the CUT Icon. A Dialog Box appears. Click on the Forward and Back Option. Use the Through All settings for both directions and hit the ENTER Key. Select the solid body and then select the rounded rectangle that you just created. Hit the ENTER Key. You now have a rounded rectangular cutout in the part. Click on the LINEAR PATTERN Icon. KUBOTEK Freedom and Precision 4
5 A Dialog Box appears. Use the Bump Features Option. Type 2 for the Number in the First Direction and 1 for the Number in the Second Direction. Make both spacings 1.25 and hit the ENTER Key. Now, move the cursor over the cutout and click on it when it highlights. Hit the ENTER Key. Click on the left end of the top, front edge of the part for the first direction and the front end of the top, left edge of the part for the second direction. You will now have a pattern of six cutouts that look like this: Select a new construction color. Now, click on the PRUNE Icon. Click on the COPY Option on the Conversation Bar. KUBOTEK Freedom and Precision 5
6 Next, click on the Feature Option on the Conversation Bar and then on the Pattern Option. Move the cursor over the pattern and click on it when it highlights. Hit the ENTER Key three times. Notice that you now have six tooling bodies nested in the cutouts. Now, click on the GRAFT Icon. A Dialog Box appears. We ll use the Cut Option. Click on Select Solid. We ll also use the Orient Graft By Face Normal and Extend Graft Body Options. Hit the ENTER Key. KUBOTEK Freedom and Precision 6
7 3 2 1 You are prompted to select the face of the target. Click on the broad, top horizontal face of the part. Next, click on the top face of one of the tooling bodies. Using the EndEnt Option, click on the top, left, front corner of the part. Now, click on the Chain Option on the Conversation Bar and then on the Pattern Option. Move the cursor over the six tooling bodies and click on them when the pattern of six highlights. Then, hit the ENTER Key twice. Notice that a manipulation axis appears at the reference point. Position the cursor over the yellow anchor and depress the left mouse button. Now, drag the manipulation axis and the tool bodies follow. Go across the horizontal surface and along the blend radius, continuing up the vertical surface. KUBOTEK Freedom and Precision 7
8 Notice that the ghost bodies track on the surface, hugging it as you move the cursor. If you position your cursor over the Blue Rotation Vector and depress and drag it, you can rotate the ghost tooling bodies. You will notice that the current angle appears as a tool tip near the manipulation axes. At any point you can click on the Angle Option on the Conversation Bar. Let s do this and type 270 for the Angle. Hit the ENTER Key to confirm. Notice that the tooling bodies snap to a 270 degree orientation. Next, click on the Position Option. Using the CtrMid Option, click on the top, front edge of the vertical leg of the part. Hit the ENTER Key to confirm the selection. Then, click on the DONE Button. You now have a pattern of cutouts rotated 270 degree on the vertical leg of the part. KUBOTEK Freedom and Precision 8
KEYCREATOR 3D Direct Modeling Software
KeyCreator Lesson KC8192 Engraving Text on a Cylindrical Surface In this exercise we ll create a tool path to engrave text on a cylindrical surface. Start with a new file in view 2. (The Front View.) Click
More informationKEYCREATOR 3D Direct Modeling Software
KeyCreator Lesson KC9203 BOM Creation with Part References In this exercise, we ll create a Bill of Material (BOM) and balloons for the simple assembly illustrated to the right. This is an assembly using
More informationDoctor Walt s Tips and Tricks # 37 Creating an Elbow Configurator Using Dynamic Face
1 Doctor Walt s Tips and Tricks # 37 Creating an Elbow Configurator Using Dynamic Face Feature-Based Solid Modelers harp on the fact that they can be used to create fancy part configurators to make families
More informationDoctor Walt s Solid Edge Version 19 Workbook 137
Still using the SMART DIMENSION Tool, click on the left vertical edge of the sketch. Move the cursor to the left and click to set the text position. Type 1.5 for the value and hit the ENTER Key. Next,
More informationTRAINING GUIDE WCS-PART-1
TRAINING GUIDE WCS-PART-1 Mastercam Training Guide Objectives The learner will create the geometry for WCS-Part-1. This Lesson will cover the following topics: Create a 3-dimensional drawing by: Creating
More informationStructural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment
ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationLesson 1 Parametric Modeling Fundamentals
1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.
More informationChapter 3. CO2 Car SolidWorks to Mastercam. A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks.
Chapter 3 CO2 Car SolidWorks to Mastercam X 2007 A. Enable MasterCam Direct. Step 1. If necessary, open your body file in SolidWorks. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box scroll
More informationGetting Started with Mastercam Solids. March 2016
Getting Started with Mastercam Solids March 2016 Mastercam 2017 Solids Getting Started TERMS OF USE Date: March 2016 Copyright 2016 CNC Software, Inc. All rights reserved. Software: Mastercam 2017 Use
More informationUSING THE TRIBALL FOR POSITIONING
USING THE TRIBALL FOR POSITIONING Although many important positioning tools are available, none are as versatile as the TriBall tool. This TriBall tool offers complete repositioning of many items: Shapes
More informationME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
More informationGETTING STARTED WITH MASTERCAM SOLIDS
GETTING STARTED WITH MASTERCAM SOLIDS June 2017 GETTING STARTED WITH MASTERCAM SOLIDS June 2017 2017 CNC Software, Inc. All rights reserved. Software: Mastercam 2018 Terms of Use Use of this document is
More informationSOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationTutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More information3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.
3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats
More informationTechnology Assignment: Scatter Plots
The goal of this assignment is to create a scatter plot of a set of data. You could do this with any two columns of data, but for demonstration purposes we ll work with the data in the table below. You
More information3D AUTOCAD. The view we ve been working in is a top or plan view. From this view even a 3D drawing will appear 2D.
3D AUTOCAD Thus far, we ve looked at tools and operations in 2D with work completed on only the X- and Y- axes. The axes symbol has been present on our screen but we haven t had much use for it. The view
More informationAutodesk Inventor 2019 and Engineering Graphics
Autodesk Inventor 2019 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the
More informationA Quick Spin on Autodesk Architectural Studio
December 2-5, 2003 MGM Grand Hotel Las Vegas A Quick Spin on Autodesk Architectural Studio Mario Guttman, AIA Kevin Durham Christie Landry (Instructor) (Assistant) (Assistant) BD13-5L Autodesk Architectural
More informationStructural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment. Kent L. Lawrence
ANSYS Workbench Tutorial Structural & Thermal Analysis using the ANSYS Workbench Release 11.0 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More informationGraphic Design & Digital Photography. Photoshop Basics: Working With Selection.
1 Graphic Design & Digital Photography Photoshop Basics: Working With Selection. What You ll Learn: Make specific areas of an image active using selection tools, reposition a selection marquee, move and
More informationExercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
More informationIntroduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
More informationPLAY VIDEO. Fences can be any shape from a simple rectangle to a multisided polygon, even a circle.
Chapter Eight Groups PLAY VIDEO INTRODUCTION There will be times when you need to perform the same operation on several elements. Although this can be done by repeating the operation for each individual
More information2 SELECTING AND ALIGNING
2 SELECTING AND ALIGNING Lesson overview In this lesson, you ll learn how to do the following: Differentiate between the various selection tools and employ different selection techniques. Recognize Smart
More information4 TRANSFORMING OBJECTS
4 TRANSFORMING OBJECTS Lesson overview In this lesson, you ll learn how to do the following: Add, edit, rename, and reorder artboards in an existing document. Navigate artboards. Select individual objects,
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More informationAUTODESK FUSION 360 Designing a RC Car Body
AUTODESK FUSION 360 Designing a RC Car Body Abstract This project explores how to use the sculpting tools available in Autodesk Fusion 360 Ultimate to design the body of a RC car. John Helfen john.helfen@autodesk.com
More informationSolid Bodies and Disjointed bodies
Solid Bodies and Disjointed bodies Generally speaking when modelling in Solid Works each Part file will contain single solid object. As you are modelling, each feature is merged or joined to the previous
More informationParametric Modeling Design and Modeling 2011 Project Lead The Way, Inc.
Parametric Modeling Design and Modeling 2011 Project Lead The Way, Inc. 3D Modeling Steps - Sketch Step 1 Sketch Geometry Sketch Geometry Line Sketch Tool 3D Modeling Steps - Constrain Step 1 Sketch Geometry
More informationAutodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
More informationChapter 6. Concept Modeling. ANSYS, Inc. Proprietary Inventory # May 11, ANSYS, Inc. All rights reserved.
Chapter 6 Concept Modeling 6-1 Contents Concept Modeling Creating Line Bodies Modifying i Line Bodies Cross Sections Cross Section Alignment Cross Section Offset Surfaces From Lines Surfaces From Sketches
More information3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
More informationLesson 5 Solid Modeling - Constructive Solid Geometry
AutoCAD 2000i Tutorial 5-1 Lesson 5 Solid Modeling - Constructive Solid Geometry Understand the Constructive Solid Geometry Concept. Create a Binary Tree. Understand the basic Boolean Operations. Create
More informationL E S S O N 2 Background
Flight, Naperville Central High School, Naperville, Ill. No hard hat needed in the InDesign work area Once you learn the concepts of good page design, and you learn how to use InDesign, you are limited
More informationsolidthinking Environment...1 Modeling Views...5 Console...13 Selecting Objects...15 Working Modes...19 World Browser...25 Construction Tree...
Copyright 1993-2009 solidthinking, Inc. All rights reserved. solidthinking and renderthinking are trademarks of solidthinking, Inc. All other trademarks or service marks are the property of their respective
More informationShape and Line Tools. tip: Some drawing techniques are so much easier if you use a pressuresensitive
4Drawing with Shape and Line Tools Illustrator provides tools for easily creating lines and shapes. Drawing with shapes (rectangles, ellipses, stars, etc.) can be a surprisingly creative and satisfying
More informationSolidWorks 2013 and Engineering Graphics
SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following
More informationLESSON 2 MODELING BASICS
LESSON 2 MODELING BASICS In this lesson we ll start to model a multi-story office building from scratch. We ll construct the base grid, create the two towers and place slabs between the stories. Also we
More informationLesson 14 Blends. For Resources go to > click on the Creo Parametric 2.0 Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Hole Pattern REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
More informationConstructing treatment features
Constructing treatment features Publication Number spse01530 Constructing treatment features Publication Number spse01530 Proprietary and restricted rights notice This software and related documentation
More information3D Modeler Creating Custom myhouse Symbols
3D Modeler Creating Custom myhouse Symbols myhouse includes a large number of predrawn symbols. For most designs and floorplans, these should be sufficient. For plans that require that special table, bed,
More informationAutodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360
Overview Modeling techniques in Fusion 360 Modeling in Fusion 360 is quite a different experience from how you would model in conventional history-based CAD software. Some users have expressed that it
More informationBobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill?
BobCAD-CAM FAQ #50: How do I use a rotary 4th axis on a mill? Q: I ve read FAQ #46 on how to set up my milling machine. How do I enable 4th axis to actually use it? A: Enabling 4th axis in the machine
More information1 General Principles. General Principles. In this chapter 1-1
1 General Principles In this chapter 1 General Principles 1.1 User Interface 1.2 Title bar 1.3 Menu bar 1.4 Standard Toolbar 1.5 The drawing area 1.6 Component tabs 1.7 Status Bar 1.8 Manipulating Components
More informationModule 4A: Creating the 3D Model of Right and Oblique Pyramids
Inventor (5) Module 4A: 4A- 1 Module 4A: Creating the 3D Model of Right and Oblique Pyramids In Module 4A, we will learn how to create 3D solid models of right-axis and oblique-axis pyramid (regular or
More informationEquipment Support Structures
Equipment Support Structures Overview Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform Columns Creating Plates with Openings Bracing
More informationIntroduction. Using Shapes. Word 2010 Working with Shapes. Video: Working with Shapes in Word To Insert a Shape: Page 1
Word 2010 Working with Shapes Introduction Page 1 You can add a variety of shapes to your document including arrows, callouts, squares, stars, flowchart shapes and more. Want to set your name and address
More informationBeginning Tutorial the Lego
Beginning Tutorial the Lego In this tutorial, you will construct a simple hollowed-out block with a hole in it (looks like a Lego). You will learn the basics of creating and modifying sketches and features.
More informationUnit #13 : Integration to Find Areas and Volumes, Volumes of Revolution
Unit #13 : Integration to Find Areas and Volumes, Volumes of Revolution Goals: Beabletoapplyaslicingapproachtoconstructintegralsforareasandvolumes. Be able to visualize surfaces generated by rotating functions
More informationStrategy. Using Strategy 1
Strategy Using Strategy 1 Scan Path / Strategy It is important to visualize the scan path you want for a feature before you begin taking points on your part. You want to try to place your points in a way
More informationLesson 14 Blends. For Resources go to > click on the Creo Parametric Book cover
Lesson 14 Blends Figure 14.1 Cap OBJECTIVES Create a Parallel Blend feature Use the Shell Tool Create a Swept Blend REFERENCES AND RESOURCES For Resources go to www.cad-resources.com > click on the Creo
More information1. Move your mouse to the location you wish text to appear in the document. 2. Click the mouse. The insertion point appears.
Word 2010 Text Basics Introduction Page 1 It is important to know how to perform basic tasks with text when working in a word processing application. In this lesson you will learn the basics of working
More informationEquipment Support Structures
Page 1 Equipment Support Structures Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform
More informationTransforming Objects in Inkscape Transform Menu. Move
Transforming Objects in Inkscape Transform Menu Many of the tools for transforming objects are located in the Transform menu. (You can open the menu in Object > Transform, or by clicking SHIFT+CTRL+M.)
More informationQuickTutor. An Introductory SilverScreen Modeling Tutorial. Solid Modeler
QuickTutor An Introductory SilverScreen Modeling Tutorial Solid Modeler TM Copyright Copyright 2005 by Schroff Development Corporation, Shawnee-Mission, Kansas, United States of America. All rights reserved.
More informationSolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
More informationSolid Bodies and Disjointed Bodies
Solid Bodies and Disjointed Bodies Generally speaking when modelling in Solid Works each Part file will contain single solid object. As you are modelling, each feature is merged or joined to the previous
More informationLESSON 14 LEARNING OBJECTIVES. After completing this lesson, you will be able to:
LEARNING OBJECTIVES After completing this lesson, you will be able to: 1. Construct 6 Solid model Primitives: Box, Sphere, Cylinder, Cone, Wedge and Torus LESSON 14 CONSTRUCTING SOLID PRIMITIVES AutoCAD
More informationMASTERCAM DYNAMIC MILLING TUTORIAL. June 2018
MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 MASTERCAM DYNAMIC MILLING TUTORIAL June 2018 2018 CNC Software, Inc. All rights reserved. Software: Mastercam 2019 Terms of Use Use of this document is subject
More information3 Polygonal Modeling. Getting Started with Maya 103
3 Polygonal Modeling In Maya, modeling refers to the process of creating virtual 3D surfaces for the characters and objects in the Maya scene. Surfaces play an important role in the overall Maya workflow
More informationMaya Lesson 6 Screwdriver Notes & Assessment
Maya Lesson 6 Screwdriver Notes & Assessment Save a new file as: Lesson 6 Screwdriver YourNameInitial Save in your Computer Animation folder. Screwdriver Handle Base Using CVs Create a polygon cylinder
More informationMET 107 Drawing Tool (Shapes) Notes Day 3
MET 107 Drawing Tool (Shapes) Notes Day 3 Shapes: (Insert Tab Shapes) Example: Select on the rounded rectangle Then use the mouse to position the upper left corner and produce the size by dragging out
More informationIn this tutorial, you will create the model of a chair, as shown in the image below, using the extended primitives and modifiers.
Office Chair In this tutorial, you will create the model of a chair, as shown in the image below, using the extended primitives and modifiers. Creating the Project Folder Create a new project folder with
More informationOn the ribbon bar, click the Select from Sketch button.
On the Features toolbar, click the Revolved Protrusion command. On the ribbon bar, click the Select from Sketch button. In the part window, select the Sketch, and on the ribbon bar click the Accept button.
More informationPiping Design. Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index
Piping Design Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index Dassault Systèmes 1994-2001. All rights reserved. Site Map Piping Design member member
More informationAppendix B: Creating and Analyzing a Simple Model in Abaqus/CAE
Getting Started with Abaqus: Interactive Edition Appendix B: Creating and Analyzing a Simple Model in Abaqus/CAE The following section is a basic tutorial for the experienced Abaqus user. It leads you
More informationTechnique or Feature Where Introduced
Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around
More informationDrawing shapes and lines
Fine F Fi i Handmade H d d Ch Chocolates l Hours Mon Sat 10am 6pm In this demonstration of Adobe Illustrator CS6, you will be introduced to new and exciting application features, like gradients on a stroke
More informationGetting Started With XPresReview
Getting Started With XPresReview Step One : Downloading & Installing The XPresReview Software Cagenix utilizes a software package called XpresReview for our design approval process. DOWNLOAD LINK : http://xpresreview.cagenix.com
More informationParametric Modeling. With. Autodesk Inventor. Randy H. Shih. Oregon Institute of Technology SDC PUBLICATIONS
Parametric Modeling With Autodesk Inventor R10 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com 2-1 Chapter 2 Parametric
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationA Guide to Autodesk Maya 2015
A Guide to Autodesk Maya 2015 Written by Mitchell Youngerman Table of Contents Layout of Toolbars...pg 1 Creating Objects...pg 2 Selecting & Deselecting Objects...pg 3 Changing Perspective... pg 4 Transforming
More informationDesigning a Chair. Lesson 6
Lesson 6 Designing a Chair This lesson illustrates how to design a chair using the Curves Network modeling tool. The following modeling tools will be covered: Curves Network. Skin. Intersect. Trim. Mirror.
More informationDesign a Simple Fan in 123D Design
Design a Simple Fan in 123D Design Learn to use 123D Design to make and print this simple fan. 123D Design is a free, powerful, yet simple 3D creation and editing tool. It allows you to design and build
More informationSpira Mirabilis. Finding the Spiral tool. Your first spiral
Spira Mirabilis Finding the Spiral tool The Spiral tool is part of ShapeWizards suite called MagicBox (the other tools in the suite are Pursuit, Shell, Sphere). You can install all these tools at once
More informationSNOWFLAKES PHOTO BORDER - PHOTOSHOP CS6 / CC
Photo Effects: Snowflakes Photo Border (Photoshop CS6 / CC) SNOWFLAKES PHOTO BORDER - PHOTOSHOP CS6 / CC In this Photoshop tutorial, we ll learn how to create a simple and fun snowflakes photo border,
More informationTRAINING GUIDE SOLIDS-LESSON-3
TRAINING GUIDE SOLIDS-LESSON-3 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing
More informationSelective Space Structures Manual
Selective Space Structures Manual February 2017 CONTENTS 1 Contents 1 Overview and Concept 4 1.1 General Concept........................... 4 1.2 Modules................................ 6 2 The 3S Generator
More informationFAGOR AUTOMATION MC TRAINING MANUAL
FAGOR AUTOMATION MC TRAINING MANUAL ACER MC TRAINING MANUAL 8 holes 1/2" depth grid pattern R0.125 1.5 6 unit: inch R0.25 4 1.25 2 2.675 1/2" depth rectangular pocket 1/2" depth circular pocket R0.75 8
More informationModule 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
More informationFeature-based CAM software for mills, multi-tasking lathes and wire EDM. Getting Started
Feature-based CAM software for mills, multi-tasking lathes and wire EDM www.featurecam.com Getting Started FeatureCAM 2015 R3 Getting Started FeatureCAM Copyright 1995-2015 Delcam Ltd. All rights reserved.
More informationSolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
More information3D Design with 123D Design
3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A
More informationSETTING UP A. chapter
1-4283-1960-3_03_Rev2.qxd 5/18/07 8:24 PM Page 1 chapter 3 SETTING UP A DOCUMENT 1. Create a new document. 2. Create master pages. 3. Apply master pages to document pages. 4. Place text and thread text.
More informationControl the Workplane
Control the Workplane This tutorial outlines the procedures to understand and control the user coordinate system (UCS). You can realign and reorient the UCS to create and modify 3D objects on 2D workplanes
More informationQuick Crash Scene Tutorial
Quick Crash Scene Tutorial With Crash Zone or Crime Zone, even new users can create a quick crash scene diagram in less than 10 minutes! In this tutorial we ll show how to use Crash Zone s unique features
More informationThe Rectangular Problem
C h a p t e r 2 The Rectangular Problem In this chapter, you will cover the following to World Class standards: The tools for simple 2D Computer Aided Drafting (CAD) The Command Line and the Tray The Line
More informationModule 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts
Inventor (5) Module 4B: 4B- 1 Module 4B: Creating Sheet Metal Parts Enclosing The 3D Space of Right and Oblique Pyramids With The Work Surface of Derived Parts In Module 4B, we will learn how to create
More informationAdobe Illustrator CS5 Part 2: Vector Graphic Effects
CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Adobe Illustrator CS5 Part 2: Vector Graphic Effects Summer 2011, Version 1.0 Table of Contents Introduction...2 Downloading the
More informationCustom Shapes As Text Frames In Photoshop
Custom Shapes As Text Frames In Photoshop I used a background for this activity. Save it and open in Photoshop: Select Photoshop's Custom Shape Tool from the Tools panel. In the custom shapes options panel
More informationThis project covers the following design concepts:
Design Project 4 This project covers the following design concepts: DRAWING TOOLS SNAP TO GRID SETTING CONSTRAINTS CUT PATH TOOL CENTERLINE TEXT COPY & PASTE CONFORMING VECTOR CREATING A CLOSED REGION
More informationLesson for levels K-5 Time to complete: min
Lesson Plan: Lesson for levels K-5 Time to complete: 45-90 min Lesson Plan: Level: Grades K-5 (ages 5-10) Time to complete: ~45-90 minutes Learn how to build basic geometry, apply materials, and import
More information4) Finish the spline here. To complete the spline, double click the last point or select the spline tool again.
1) Select the line tool 3) Move the cursor along the X direction (be careful to stay on the X axis alignment so that the line is perpendicular) and click for the second point of the line. Type 0.5 for
More informationCreating and Analyzing a Simple Model in Abaqus/CAE
Appendix B: Creating and Analyzing a Simple Model in Abaqus/CAE The following section is a basic tutorial for the experienced Abaqus user. It leads you through the Abaqus/CAE modeling process by visiting
More informationElectrical Cableway Routing
Electrical Cableway Routing Preface Using This Guide What's New? Getting Started Entering the Workbench Placing a Hanger Routing a Loft Through Hangers Placing a Conduit on a Run Saving Documents Updating
More informationTRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
More informationDesignWorks- CrystalWork Skillbuilder
DesignWorks- CrystalWork Skillbuilder Crystal Shapes & Fills The following exercise will cover the basics of filling and editing a Crystal shape. For detailed CrystalWork software instructions, review
More information