MAZDA Application Purchase and Installation Guide

Transcription

1 MAZDA Application Purchase and Installation Guide NOTE: This process is subject to change w/o notice. Go to Move mouse over Mazda Module Reprogramming and then click on PCM Reprogramming Codes. Doc. # G1 Section G1 Page 1 of 6

2 MAZDA Application Purchase and Installation Guide Click Here on applicable subscription duration. This example will show 1 Year Subscription. Click on Check Out. Review Shopping Cart and click on Continue Check Out. Fill out information as required and click on Continue Check Out. Doc. # G1 Section G1 Page 2 of 6

3 MAZDA Application Purchase and Installation Guide Begin Checkout by confirming information on screen and select Continue Check Out. Read Mazda Tech Info Commercial Terms, select I ve Read the Terms & Accept and, if agreeable, select Continue Check Out. Enter applicable Credit Card information and select Continue Check Out. Doc. # G1 Section G1 Page 3 of 6

4 MAZDA Application Purchase and Installation Guide The next screen will provide you the link to download the Mazda application and Invoice #, User ID and pre-defined Password as well as other misc. information. An will also be sent to the provided. You will be able to change your Password in the View My Account area. If you selected the Mazda application download Click on Click To Download. Click on Save, recommended to Desktop. In the case of saving the file to your Desktop, locate the MMPxx icon on your desktop and double-click on it to install the application on your PC. If you saved the file to a different location, locate the file and double-click on it from there. Doc. # G1 Section G1 Page 4 of 6

5 MAZDA Application Purchase and Installation Guide Click on Run. Click on Yes to continue. Click on Next. Enter UserName and click on Next. Application will begin to install. Doc. # G1 Section G1 Page 5 of 6

6 MAZDA Application Purchase and Installation Guide Click Finish and let PC restart to begin using Mazda Reprogramming through the FLASH2 Console. Doc. # G1 Section G1 Page 6 of 6

7 NOTE: This guide is and shows the common steps in reprogramming. Application-specific variations may not be represented. Simply follow the applicable screen prompts and proceed as indicated. This process is subject to change w/o notice. Click on the Mazda icon. Click on Flash2 Reprogramming. Read Warning information and click on Next. Make sure Ignition Switch on the VEHICLE is in the On position and click on OK. It is strongly recommended that a Battery Test be conducted. Read the notes and click on Battery Test. Section G2 Page 1 of 12

8 Battery test is within acceptable parameters. Click Next. IMPORTANT! Please read carefully and follow the directions. If you need to click on the Launch button, please see the next diagram for instructions. Otherwise, click Next and you with go into the Mazda Module Programming (MMP) Application Select Cardone Industries, In. (04.04) and then FLASH2 All-Makes Reprogrammer. Click Save Device and then Exit Application. 4 Click on Next and you ll launch into the Mazda Module Programming (MMP) Application. Section G2 Page 2 of 12

9 Click on Continue. Click on Start New Session. Click on the Tick icon. Establish an Internet connection and select Confirm. To ensure your Internet connection is functioning, open and Internet session. Section G2 Page 3 of 12

10 Read the important Warning information. NOTE: When doing off-car reprogramming, some prompts do not apply and the appropriate responses are those as if you were doing an on-car reprogramming event. Click the Tick icon to continue. Confirmation of the Vehicle Specification. Click on YES. If the Vehicle specification is not correct or communication was not established with the PCM, please refer to the Ford Blank Path documentation. These fields are OPTIONAL. Fill in the last 8 digits of the VIN number, Repair Order (RO) number and Odometer reading number. You will need to click on each box before typing this information. For more information regarding this feature, please see the Mazda Module Programming User s Guide. When done, click on the Tick icon. Click on the Toolbox Tab. Section G2 Page 4 of 12

11 Click on Module Programming and then the Tick icon. Click on Module Reprogramming, then PCM, then the Tick mark. Click Yes. Ensure Internet Connection and click Confirm. Section G2 Page 5 of 12

12 Read and click the Tick mark. Click the Tick mark. Click Yes. Read and click the Tick mark. Where there is an arrow, you may click on the option(s) listed on the left side of the screen. Help information will appear on the right. Click on Exit and then click the Tick mark when done. Section G2 Page 6 of 12

13 Read and proceed by clicking on the Tick mark. Turn ignition switch Off and click on the Tick mark. Click on the Tick mark. Turn ignition switch to ON and click on the Tick mark. Turn ignition switch to OFF and click on the Tick mark. Section G2 Page 7 of 12

14 Turn ignition switch to ON and click on the Tick mark. Downloading data! Turn ignition switch to OFF and click on the Tick mark. Please wait Turn ignition switch to ON and click on the Tick mark. Section G2 Page 8 of 12

15 Turn ignition switch to OFF and click on the Tick mark. Click on the Tick mark. Click on the Tick mark. Read and click on the Tick mark. Start Engine and click on the Tick mark. Section G2 Page 9 of 12

16 Turn ignition switch to OFF and click on the Tick mark. Turn ignition switch to ON and click on the Tick mark. Clearing Fault Codes Turn ignition switch to OFF and click on the Tick mark. Programming complete. Click on the Toolbox. Section G2 Page 10 of 12

17 Click on Delete to delete the session. More information on how to use these features is available in the Mazda User Guide. Close out of the MMP by clicking on the X in the upper right corner. Click on the green check mark. Click on Get Status to see changes that were made. Click Finish when done. Section G2 Page 11 of 12

18 BLANK PAGE Section G2 Page 12 of 12