Vane Pump Series SDV. Fixed Displacement zp14. Catalogue HY0738-A/CH November Hydraulics. Hydraulics

Transcription

1 SDV Fixed Displacement zp4 Catalogue HY078-/CH November 004

2 Contents SDV Introduction General applications instructions... Maximum speed... Pressure ratings... Minimum allowable inlet pressure... General characteristics... SDV0 Ordering code... 4 Operating characteristics... 4 Technical data... 4 Dimensions... SDV0 Ordering code... Operating characteristics... Technical data... Dimensions... 7 SDV00 Ordering code... 8 Operating characteristics... 8 Technical data... 8 Dimensions... 9 SDV00 Ordering code... 0 Operating characteristics... 0 Technical data... 0 Dimensions... General aplications Instructions. Check speed range, pressure, temperature, fluid quality, viscosity and pump rotation.. Check inlet conditions of the pump, if it can accept application requirement.. Type of shaft : if would support operating torque. 4. Coupling must be chosen to minimize pump shaft load (misalignment,weight).. Filtration : must be adequate for lowest contamination level.. Environment of pump : avoid pollution,shocks and noise reflection

3 Technical data SDV Minimum and maximum speed, pressure ratings SDV0 SDV0 Size Theoretical Displacement Vi Maximum speed HF-0, HF- HF- HF-, HF-4 HF- Maximum pressure HF-0, HF- HF-, HF-4, HF- HF- Int. Cont. Cont Cont. cm/rev (in/rev) RPM RPM Bar (psi) Bar (psi) Bar (psi) Bar (psi), (.0) (00) 0 (0) 0 (900) 00 (00), (.40) (00) 0 (0) 0 (900) 00 (00) 9,8 (.0) (00) 0 (0) 0 (900) 00 (00) 4, (.80) (00) 0 (0) 0 (900) 00 (00),4 (.00) (00) 0 (0) 0 (900) 00 (00) 9, (.9) (00) 40 (000) 0 (900) 00 (00) 7,8 (.9) (000) 40 (000) 0 (900) 00 (00) 9, (.9) (00) 0 (0) 0 (900) 0 (00) 7,8 (.9) (00) 0 (0) 0 (900) 0 (00) 8, (.) (00 0 (0) 0 (900) 0 (00) 9 9,7 (.8) (00) 0 (0) 0 (900) 0 (00),4 (.) (00) 0 (0) 0 (00) 00 (400) 9,0 (.8) (00) 40 (000) 0 (00) 00 (400) 4,4 (.9) (00) 40 (000) 0 (00) 00 (400) HF-0, HF- = nti-wear petroleum base. HF- = Non anti-wear petroleum base. HF- = Synthetic fluids. HF- = Water-in-oil invert emulsions. HF-4 = Water glycol solutions. Minimum speed is 00 RPM For further information, if the performance characteristics outlined above do not meet your own particular requirements, please consult your local Parker office. Minimum allowable inlet pressure (bar absolute / psi) Ring size Speed (RPM) Size 0,8 0,9 SDV0 4 0,8 0,9 4 0,8 0,9 0,8,00 (4.) 7 0,8,00 (4.) 7 0,8 0,9,0 (4.) ,8 0,9 8 SDV0 9 0,9 9 0,9 0,8,0 (4.9) 0,9,0 (.) Multiply absolute pressure by, for HF-, HF-4 fluids. by, for HF- fluids. by,0 for ester or rapeseed base Use the cartridge with the highest absolute pressure for double pumps. General characteristics Moment of Mounting Weight inertia Port connections standard kg (lb) kgm x0-4 (lb.in ) Suction Pressure Code P S B P S B SDV0 SE (0 -) 0. (0.7) NPTF -/ UNF-B G / NPTF /4 UNF-B G / SDV0 SE (-8). (0.7) -/4 NPTF -/8 UNF-B G -/4 /4 NPTF -/ UNF-B G /4 Code F S B P* P** P-P SDV00 SE B. ( 0.0). (0.90) 4 bolts flange -/ dia -/ UNF-B /4 UNF-B *** SDV00 SE B.9 (.0) 4. (.0) 4 bolts flange dia -/ UNF-B -/ UNF-B G /4 * P = Pressure port near the shaft ** P = Pressure port near the cover end *** P = G /4 P = G /

4 Ordering code Model No. SDV 0 - P S - C L - P SDV0 Vane pump 0 Mounting = -bolt flange, /4 pilot (SE ) (standard) Inlet port connections P = NPTF thread S = /- UNF-B thread B = G (BSPP) Ring size (Delivery at 00 rpm and 00 psi) = USgpm = USgpm = USgpm 4 = 4 USgpm = USgpm = USgpm 7 = 7 USgpm Operating characteristics Model SDV0 Internal leakage qvs l/min [GPM] Ring Size Displ. cm /rev (in /rev) Max. Pressure bar (psi), (.0) 7 (00), (.40) 7 (00) 9,8 (.0) 7 (00) 4, (.80) 7 (00),4 (.00) 7 (00) 9, (.9) (00) 7,8 (.9) 8 (000) Internal leakage (typical) & 7 rings 4 & rings, & rings Speed RPM Do not operate pump more than seconds at any speed or viscosity if internal leakage is higher than 0% of theoretical flow. Total leakage is the sum of each section loss at its operating conditions. Typical delivery L/min (Usgpm) Identity Shaft rotation (view on shaft end) L = Counter-clockwise Omit for clockwise Position of outlet port (Viewed from cover end of pump) = Opposite inlet port B = 90 CCW from inlet C = In line with inlet D = 90 CW from inlet Shaft = Straight keyed = Splined 8 = teeth - /4 OD Outlet port connections P = / NPTF thread S = /4 - UNF-B thread B = G / (BSPP) Typical input power KW (hp) 0 bar 0 PSI 0 bar 000 PSI 7 bar 80 PSI 7 bar 00 PSI 00 4,0,0,0 0, 0,07 0,09 0,7 0,9 00,0,,0 0,8 0,09 0,,08,44 800,9,,9,0 0,0 0,4,44,9 00 7,9,,9, 0,4 0,8,, ,9, 7,9, 0,7 0,,88,8 800,9, 9,9, 0, 0,8,0 4,8 00,8, 9,8, 0,0 0,7, 4, ,7,9,7,4 0, 0,4 4,, 800 7, 4,7, 4, 0, 0,4,70 7, 00,7 4,,, 0,7 0,7 4,49,0 00 9,7,, 4, 0,4 0,4,9 7,94 800,, 0,, 0,4 0, 7, 9, ,7,, 4, 0,4 0,4,94 7,9 00 4,,,, 0,4 0,7 7,7 0, 800 9, 7,8,,9 0, 0,9 9,,77 00,4, 9,, 0,4 0, 7,00 9,9 00 9, 7,7,, 0, 0,8 9,, 800, 9, 0,9 8, 0, 0,8,7, 00 7,4 7,,, 0,48 0,4 8,44, 00 4, 9,0 0,0 7,9 0,0 0,94 4, ,0 0,8,8 9,7 0,7 0,9,4 8,0 Lp. Noise level [db()] m ISO RPM 00 RPM 800 RPM Noise level (typical) SDV

5 Dimensions SDV0 Inlet port "/ - UNF - B thd. (shown) or " NPTF thd. or G ",70 (.0) 7,9 (.) 4 (DI..8) 4 (DI..8) 9,0 9,0 (DI..8) 8, 8,0 (DI..0/.48) Outlet port /4" - UNF - B thd. (shown) or /" NPTF thd. or G /" 7,0 (.00) 8,0 (.0),70 (.47) 4,0 (.97) B 44,40 (.7) 4, (DI..),/,00 (.8/.87) Sq 4,7 (.87) key,4 (.00) long 40,0 (DI..7) Clockwise rotation SE "" flange 8,0 (.0) 4,70 (.8) Number shaft,80 (.) Involute spline Flat root - 9 teeth / diametral pitch Pitch dia (.) Major dia. -,8/,80 (./.) Minor dia. -,8/,00 (.48/.47), (.087), /,0 (.0/.40).(DI..47) holes,8 (.) Number 8 shaft, (.09) 0,0 (4.9) 0,00 (DI..) Involute spline Flat root - teeth / diametral pitch Pitch dia (.874) Minor dia. -,87/. (.48/.0) 9, (DI..7) Ring size 7,90 (.) Dimensions B Weight Kg (lb), (DI..98) 0, (.8) 9,0 8,9 (DI..748/.74), (4.) 9,9 (.) 4, - (0.0), (4.) 9,9 (.) 4, - (0.0), (4.) 9,9 (.) 4, - (0.0) 4,9 (4.80) 98, (.87), - (.),9 (4.80) 98, (.87), - (.) 7,0 (.00) 0,4 (4.07),8 - (.0) 7 7,0 (.00) 0,4 (4.07),8 - (.0) Weight: SDV 0 : 4, -,8kg (0 - lb)

6 Ordering code Model No. SDV 0 - P 8 S - C L - P SDV0 Vane pump 0 Mounting = -bolt flange, /4 pilot (standard) Inlet port connections P = /4 NPTF thread S = /8 - UNF-B thread B = G /4 (BSPP) Ring size (Delivery at 00 rpm and 00 psi) = USgpm 7=7 USgpm 8=8 USgpm 9=9 USgpm 0=0 USgpm = USgpm = USgpm = USgpm Operating characteristics Model SDV0 Ring Size Displ. cm /rev (in /rev) 9, (.9) 7 (00) 7,8 (.9) 7 (00) 8, (.) 7 (00) 9 9,7 (.8) 7 (00),4 (.) 7 (00) 9,0 (.8) (00) 4,4 (.9) (00) Identity Shaft rotation (view on shaft end) L = Counter-clockwise Omit for clockwise Position of outlet port (Viewed from cover end of pump) = Opposite inlet port B = 90 CCW from inlet C = In line with inlet D = 90 CW from inlet = Splined Shaft = Straight keyed = Splined 8 = teeth - /4 OD Outlet port connections P = /4 NPTF thread S = /-UNF-B thread B = G /4 (BSPP) Max. Typical delivery Typical input power Speed Pressure L/min (Usgpm) KW (hp) bar (psi) RPM 0 bar 0 PSI 0 bar 000 PSI 7 bar 80 PSI 7 bar 00 PSI 00,40,8 9,80, 0,4 0,,8 9, 00 9, 7,7,,78 0, 0, 8,8,8 800,0 9,7,0 8, 0, 0,7 0,8 4, 00 7, 7,,9,80 0,4 0, 7, 0, 00 4,0 9,04 8,80 7, 0, 0,7 9,9, 800 4,04 0,84,4 9,4 0, 0,9,,4 00,80 8,40,40,97 0, 0,7 9,, 00 9,7 0,0 4, 9,08 0, 0,8,8, ,70,0 4,0,8 0,7,0 4, 9, 00,4 9,4 0,4 7,99 0, 0,7 0,4, ,,77 9, 0,4 0,7 0,9,4 8,0 800,4 4, 48,0,70 0,8,,, 00 4,8,4 40,8 0,4 0,7 0,9,8 8, 00 4,0 4,4,0, 0,8, 7,, 800, 7,,,4,0,4, 8, 00 4,80, 4,0, 0,7,0 4, 9, 00 8,0,4 4,0 4, 0,9, 8,, ,0 8,,00 7,44,,, 0,4 00 0,88,44 4,8, 0,8,,0, 00,0,80 9,40,9,0, 0,4 7, 800 7, 0, 7, 9,0,, 4,7, Internal leakage (typical) Noise level (typical) SDV0 - Internal leakage qvs l/min [GPM] ,8 & 9 rings & rings ring ring Do not operate pump more than seconds at any speed or viscosity if internal leakage is higher than 0% of theoretical flow. Total leakage is the sum of each section loss at its operating conditions. Lp. Noise level [db()] m ISO RPM 00 RPM 800 RPM

7 Dimensions Outlet port "/ - UNF - B thread SE O-ring boss connection or /4" NPTF thd or G /4" Number Shaft SDV0 8, 8,0 (DI..0/.48) B,0 (.),70 (.0) Inlet port "/4 NPTF or "/8 - UNF - B thd. SE O-ring boss connection or G "/4 Clockwise rotation,0 (.9),0 (.9),00 (.0) 4,00 (.) 7,0 (.), (.) Sq 4,7 (.87) key 4, (.) long 47,0 (DI..8) 0,0 (4.87), (.09) SE "" flange Number shaft Ring size 74,80 (.94) 7,0 (.47),0 (.9) Involute spline Flat root - teeth / diametral pitch Pitch dia (.874) Minor dia. -.87/. (.48/.47) 9,0 8,9 (DI..748/.74) Dimensions B Weight Kg (lb), (4.9) 0, (4.0) 7, - (.0) 7, (.8) 08,4 (4.7) 7,7 - (7.0) 8, (.8) 08,4 (4.7) 7,7 - (7.0) 9, (.8) 08,4 (4.7) 7,7 - (7.0), (.8), (4.47) 8,0 - (7.) 40, (.) 7, (4.) 8, - (8,0) 40, (.) 7, (4.) 8, - (8.0),80 (.),0 (.08),8 (.48) 4,4 (.7) Number shaft 4,70 (.8) 7,9 (.) 9, (DI..) 40,9 (DI..) 9,0 / 9,0 (DI..70/.749),0 /,00 (.8/.87). (DI..47) holes Involute spline Flat root - 9 teeth / diametral pitch Pitch dia (.) Major dia. -.8/.80 (./.) Minor dia. -.8/.00 (.48/.47) 0,0 (DI..) Number 8 shaft,8 (.) 9. (DI..7) Involute spline Flat root - teeth / diametral pitch Pitch dia (.874) Minor dia. -.87/. (.48/.0) 0, (.8) 9,0 8,9 (DI..748/.74) Weight: SDV 0 : 7, - 8,kg ( - 8 lb) 7

8 Ordering code SDV00 Model No. SDV 00 - F S S - CC - L - P Vane pump 00 Mounting = -bolt flange, 4 pilot (standard) Inlet port connections F = 4 bolt flange / dia Shaft-end pump ring size (Delivery at 00 rpm and 00 psi) = USgpm 7 = 7 USgpm 8 = 8 USgpm 9 = 9 USgpm = USgpm = USgpm = USgpm No outlet port (shaft end) S = / - UNF-B thd B = G /4 (BSPP) Cover-end pump ring size (Delivery at 00 rpm and 00 psi = USgpm = USgpm = USgpm 4 = 4 USgpm = USgpm = USgpm 7 = 7 USgpm Operating characteristics Identity Shaft rotation (view on shaft end) L = Left hand for counter-clockwise Omit for right hand Position of outlet port (Viewed from cover end of pump) With n outlet opposite inlet = N outlet CCW from inlet B = N outlet 4 CCW from inlet C = N outlet 4 CW from inlet D = N outlet CW from inlet With n outlet 90 CCW from inlet B = N outlet CCW from inlet BB = N outlet 4 CCW from inlet BC = N outlet 4 CW from inlet BD = N outlet CW from inlet With n outlet in line with inlet C = N outlet CCW from inlet CB = N outlet 4 CCW from inlet CC = N outlet 4 CW from inlet CD = N outlet CW from inlet With n outlet 90 CW from inlet D = N outlet CCW from inlet DB = N outlet 4 CCW from inlet DC = N outlet 4 CW from inlet DD = N outlet CW from inlet Shaft = Straight keyed = Splined N outlet port (cover end) S = /4 - UNF-B thread B = G / (BSPP) Model Ring Size Displ. cm /rev (in /rev) Max. Pressure bar (psi) P P 9, (.9) 7 (00) 7,8 (.9) 7 (00) 8, (.) 7 (00) 9 9,7 (.8) 7 (00),4 (.) 7 (00) 9,0 (.8) (00) 4,4 (.9) (00), (.0) 7 (00), (.40) 7 (00) 9,8 (.0) 7 (00) 4, (.80) 7 (00),4 (.00) 7 (00) 9, (.9) (00) 7,8 (.9) 8 (000) Please refer to page 4 Please refer to page 8

9 Dimensions N OUTLET PORT "/ - UNF - B THD or G /4",0 (4.8) 4,0 (.9),0 (.9) /"- UNC-B THD., (.88) DEEP 4 HOLES,7 (.40) 7,8 (.70) 9,8 (.70) 4,9 (.7) 0,0 (.8) VIEW - 7,0.00) 0,8.00) INLET PORT 8, (DI..0) B Number shaft extension,70 (.0) 9,40 (.7) C,90 (.0) N OUTLET PORT "/ - UNF - B THD or G /4" 8,70 (.),0 (.) 4,4 / 4,4 (DI..9/.9) 0,0 / 0, (DI /.998) SDV00 7, (.88) 4. (DI..) THRU HOLES Number shaft 7,8 (.) Clockwise rotation 4,0 (.7) 0.7 (DI ,90 ((DI..70) 9,0 (DI..0) nvolute spline Flat root - teeth Pitch dia (.8) Major dai. -./. (.87/.87) Minor dai. - 8./8. (.7/.7),,0 (DI..87/.874) 0 0 0,0 (4.87) Ring size Dimension Ring size Dimension Cover end Shaft end B C Cover end Shaft end B C Weight Kg(Ib),,, 07. (8. 7) 8. (7.4) 07. (4. 7) 4, 0, (8. 88) 0. (7. 9) 8. (4. ),,, 7, 8, 9. (8. 409) (7.47). (4. 49) 4,, 8. (8. 99) (8. 0) (4. 80),,, 0, 8. (8. 0) (7.7) 8. (4. ), 7 8. (8. 0) (7. 7) 07. (4. 7),,,,. (8. 744) (7.8) (4. 80), 7 7,8, 9 (8. 88) 0. (7. 9). (4. 49).(0) Internal leakage qvs l/min [GPM] ,. (8. 409) (7.47) 07. (4. 7), 7 0, 0 (9. 0) 0. (8. ) 8. (4. ) 4, 7, 8, 9 0 (8. ) 9. (7.78). (4. 49), 7,. (9. 9) (8. 0) (4. 80) Do not operate pump more than seconds at any speed or viscosity if internal leakage is higher than 0% of theoretical flow. Double pump noise level is given with each section discharging at the pressure noted on the curve. Total leakage is the sum of each section loss at its operating conditions. Internal leakage (typical) V0 7, 8 & 9 rings V0 & rings V0 ring V0 ring V0 & 7 rings V0 4 & rings V0, & rings Lp. Noise level [db()] m ISO RPM 00 RPM 800 RPM Noise level (typical) SDV

10 Ordering code SDV00 Model No. SDV 00 - F S 8 - CC - L - P Vane pump 00 Mounting = -bolt flange, 4 pilot (standard) = -bolt flange, /4 pilot (optional) Inlet port connections F = 4 bolt flange.00 dia Shaft-end pump ring size (Delivery at 00 rpm and 00 psi) = USgpm 7 = 7 USgpm 8 = 8 USgpm 9 = 9 USgpm = USgpm = USgpm = USgpm No outlet port (shaft end) S = / - UNF-B thd B = G /4 (BSPP) Cover-end pump ring size (Delivery at 00 rpm and 00 psi = USgpm 7 = 7 USgpm 8 = 8 USgpm 9 = 9 USgpm = USgpm Operating characteristics Identity Shaft rotation (view on shaft end) L = Left hand for counter-clockwise Omit for right hand Position of outlet port (Viewed from cover end of pump) With n outlet opposite inlet = N outlet opposite inlet B = N outlet 90 CCW from inlet C = N outlet in line with inlet D = N outlet 90 CW from inlet With n outlet 90 CCW from inlet B = N outlet opposite inlet BB = N outlet 90 CCW from inlet BC = N outlet in line with inlet BD = N outlet 90 CW from inlet With n outlet in line with inlet C = N outlet opposite inlet CB = N outlet 90 CCW from inlet CC = N outlet in line with inlet CD = N outlet 90 CW from inlet With n outlet 90 CW from inlet D = N outlet opposite inlet DB = N outlet 90 CCW from inlet DC = N outlet in line with inlet DD = N outlet 90 CW from inlet Shaft = Straight keyed = Splined N outlet port (cover end) S = / - UNF-B thread B = G /4 (BSPP) Model P & P Ring Size Displ. cm /rev (in /rev) Max. Pressure bar (psi) 9, (.9) 7 (00) 7,8 (.9) 7(00) 8, (.) 7 (00) 9 9,7 (.8) 7(00),4 (.) 7 (00) 9,0 (.8) (00) 4,4 (.9) (00) Speed RPM Typical delivery L/min (Usgpm) Typical input power KW (hp) 0 bar 0 PSI 0 bar 000 PSI 7 bar 80 PSI 7 bar 00 PSI 00,40,8 9,80, 0,4 0,,8 9, 00 9, 7,7,,78 0, 0, 8,8,8 800,0 9,7,0 8, 0, 0,7 0,8 4, 00 7, 7,,9,80 0,4 0, 7, 0, 00 4,0 9,04 8,80 7, 0, 0,7 9,9, 800 4,04 0,84,4 9,4 0, 0,9,,4 00,80 8,40,40,97 0, 0,7 9,, 00 9,7 0,0 4, 9,08 0, 0,8,8, ,70,0 4,0,8 0,7,0 4, 9, 00,4 9,4 0,4 7,99 0, 0,7 0,4, ,,77 9, 0,4 0,7 0,9,4 8,0 800,4 4, 48,0,70 0,8,,, 00 4,8,4 40,8 0,4 0,7 0,9,8 8, 00 4,0 4,4,0, 0,8, 7,, 800, 7,,,4,0,4, 8, 00 4,80, 4,0, 0,7,0 4, 9, 00 8,0,4 4,0 4, 0,9, 8,, ,0 8,,00 7,44,,, 0,4 00 0,88,44 4,8, 0,8,,0, 00,0,80 9,40,9,0, 0,4 7, 800 7, 0, 7, 9,0,, 4,7, 0

11 Dimensions SDV00,0 (.9),0 (4.8) /" - UNC - B thd..94 deep - 4 holes 77,80 (.0) N outlet port "/ - UNF - B thd. or G /4" 74,70 (.94),0 (.9) 8,90 (.) 9,80 (.7) 4,80 (.87),40 (.84) Inlet port 0.8 (DI..00) B C,70 (.0) 9,40 (.70) N OUTLET PORT "/ - UNF - B thd. or G /4" 9,40 (.70) 8,70 (.) Number shaft 7,8 (.) 7,90 (DI..70) Sq 4,8 (.87) key,8 (.) long 0,0 / 0, (DI /.99) 4,4 / 4,4 (.9/.9) 4.0 (DI..7) SE "B" flange, /,0 (DI.87/.874) Number shaft Clockwise rotation 74,80 (.88) 4,0 (.) 9,0 (DI..0) Involute spline Flat root - teeth / diametral pitch Pitch dia (.8) Major dai. -./. (.87/.87) Minor dai. - 8./8. (.7/.7) (DI. 4.7),0 (.) 4. (DI..) thru - holes Ring size Dimension Ring size Dimension Weight Kg(Ib) Cover end Shaft end B C Cover end Shaft end B C 7, 8, 9. 8 (8. 9) 88. (7. 4) 4. (4. 08) 7, 8, 9 0,. (8. 787) 00 (7. 874) 9. (4. 70) 0,. 8 (8. ) 9. (7. ) 9. (4. 70) 7, 8, 9,. 7 (8. 9) 0. (8. 0) (4. 84), 0. (8. 7) 97. (7. 70) (4. 84) 0, 0, 8. (8. 984) 0 (8. 07) 9. (4. 70). 9() 7, 8, 9 7, 8, 9 8. (8. 9) 9 (7. 77) 4. (4. 08) 0,,. 7 (9. ) 08. (8. 0) (4. 84) Internal leakage (typical) 7 Noise level (typical) SDV Internal leakage qvs l/min [GPM] ,8 & 9 rings & rings ring ring Lp. Noise level [db()] m ISO RPM 00 RPM 800 RPM Do not operate pump more than seconds at any speed or viscosity if internal leakage is higher than 0% of theoretical flow. Total leakage is the sum of each section loss at its operating conditions. Double pump noise level is given with each section discharging at the pressure noted on the curve.

12 Parker Hannifin Fluid Power Systems and Components(Shanghai) Co.,Ltd. 80 Yunqiao Road, Jin Qiao Export Processing Zone, Shanghai 00,China Tel: 8--0 Fax: Internet: Catalogue HY078-/CH November 004