Nordic - Overbed fitment

Transcription

1 Nordc - verbed ftment ssembly Instructons - lease keep for future reference mensons Wdth : 248,9 cm epth : 49,0 cm Heght : 191,3 cm Important - lease read these nstructons fully before startng assembly If you need help or have damaged or mssng parts, call the ustomer Helplne:

2 afety and are dvce Important - lease read these nstructons fully before startng assembly heck you have all the components and tools lsted on pages 3 and 4. emove all fttngs from the plastc bags and separate them nto ther groups. eep chldren and anmals away from the work area, small parts could choke f swallowed. Make sure you have enough space to layout the parts before startng. o not stand or put weght on the product, ths could cause damage. ssemble the tem as close to ts fnal poston (n the same room) as possble. ssemble on a soft level surface to avod damagng the unt or your floor. arts of the assembly wll be easer wth 2 people. We do not recommend the use of power drll/drvers for nsertng screws, as ths could damage the unt. nly use hand screwdrvers. spose of all packagng carefully and responsbly. are and mantenance nly clean usng a damp cloth and mld detergent, do not use bleach or abrasve cleaners. From tme to tme check that there are no loose screws on ths unt. hs product should not be dscarded wth household waste. ake to your local authorty waste dsposal centre. Note: f requred the next page can be cut out and used as reference throughout the assembly. eep ths page wth these nstructons for future reference. 2

3 omponents - anels If you have damaged or mssng components, call the rgos ustomer Helplne: lease check you have all the panels lsted below op x470x1 mm 6 plnth, back x1 mm 1 2 de eft x47x1 mm rawer front 18 39x17x1 mm 10 rawer sde, rght/left x x98x12 mm rawer back x98x12 mm rawer bottom NM x447x3 mm eft dvder x47x1 mm 20 ght dvder x47x1 mm de left/rght x47x1 mm 21 vder x x470x1 mm 3 4 de ght x47x1 mm oor left/rght x39x1 mm lnth, front x96x1 mm op ral xx1 mm helf x x460x1 mm 24 oor ral x x1 mm 22 op ral x80x1 mm 16 Back NM x397x3 mm oor, eft x409x1 mm 1 oor, rght x409x1 mm Back NM x397x3 mm 23 op/bottom x470x1 mm 3

4 omponents - Fttngs If you have damaged or mssng components, call the rgos ustomer Helplne: lease check you have all the panels lsted below Note: he quanttes below are the correct amount to complete the assembly. In some cases more fttngs may be suppled than are requred. B B10390 ø8x30 mm wooden dowel x36 B10400 ø6x30 mm wooden dowel 4 B10130 ø4,0x3 mm screw 4 B10170 ø4,0x3 mm screw x36 B1090 ø1x9, mm cam x70 B10603 ø/x34 mm bolt x70 B1000 ø3,x1 mm screw x72 M B10233 ø4,9/m47 mm asambly screw x8 B1002 ø1,20 mm nal x10 B10830 / mm shelf support 4 N B1021 M4x16 mm screw x8 J B10270 B10240 B ø,8x8 mm screw x36 ø6,1x, mm screw x16 wallstrap and nstructon F B1032 B1008 B mm/37 mm crossplate x12 ø26 cup hnge x12 1x1x10 mm x12 G H B10468 ø40x30 mm Wooden knob x12 B mm W rawer runner x12 B10191 M4x9 mm screw x12 d B angle x8 B1081 0x0 mm angle x8 Ba x Nal holder x1 B x1 mm connecton plate x4 ools requred uler - Use ths ruler to help correctly dentfy the screws 4

5 ssembly Instructons tep 1 Fx the drawer sdes to the drawer back 12 as shown, usng screws. 12 tep 2 nock down the dowels B nto the holes ndcated on the drawer sdes, usng a small hammer. B B B B tep 3 lde the drawer bottom 13 nto the drawer sdes 13 tep 4 crew the bolts nto the holes ndcated on the drawer fronts

6 ssembly Instructons tep ush the drawer front 10 onto the the drawer sdes as shown. ush cams nto the holes ndcated. rrow pontng towards the front. urn the cams to the rght to fx the front tep 6 Important! Make sure the! angle between the drawer front 10 and the drawer sdes s 90 before the drawer bottom s fxed. Fx the drawer bottom 13 to the drawer back 12 and the drawer front 10 usng F F 13 F 12 o adjust the angle between the drawer sdes and the drawer front push the fttng F sdewards. ee detals. tep 7 Fx the wooden knobs G to the drawer front 10 usng screws. G 10 6

7 ssembly Instructons tep 8 6 nock down the dowels nto the holes ndcated on the back plnths 6 and the top/bottom usng a small hammer. tep 9 Fx the crossplates to the sdes 1 and 4 usng the premounted screws. ee detals. oston the crossplate exactly as shown. ee detals. Fx the angles to the sdes 1, and 4 and the dvder 2 and 3 usng screws. lace the angles as shown. ee detals crew the bolts nto the holes ndcated on the sdes 1 and 4 and the dvder 2 and

8 ssembly Instructons tep 10 lde the top of the drawer runners backwards. Fx the front end of the drawer runners to the sdes 1 and 4 and the dvder 2 and 3 usng screws nto the holes ndcated. ee detals tep 2 lde the top of the drawer runners forwards. Fx the backend of the drawer runners to the sdes 1 and 4 and the dvder 2 and 3 usng screws nto the holes ndcated. ee detals

9 ssembly Instructons tep 12 lace the sdes 1 and 4 and the dvder 2 and 3 onto the bottoms and the back plnths 6. 1 ush the cams nto the holes ndcated. rrow pontng towards sdes. 2 urn the cams to the rght to fx the sdes 1 and 4 and the dvder 2 and

10 ssembly Instructons tep 13 lace the back 16 nto the rebates n the sdes/dvder 1, 2, 3 and ! Important! Make sure the angle between the top and the sdes s 90 when the back s attached. 2 6 Fx the backs to the sdes/ dvder 1, 2, 3 and 4 and the top and the back plnth usng nals. Use Nal holder d and a small hammer. lace the front plnths 7 as shown. Fx the front plnths 7 to the sdes/dvder 1, 2, 3 and 4 usng screws nto the angles

11 ssembly Instructons tep 14 lace the top ral 8 onto the top. Fx the top ral to the top usng angles W and screws. 8 x4 8 8 tep 1 Fx the crossplates to the dvder 21 on both sdes and to the sdes 20, usng the pre-mounted screws. oston exactly as shown. ee detals. crew the bolts nto the holes ndcated on the sdes 20 and the top/bottom nock down the dowels nto the holes ndcated on the top/bottom 23 usng a small hammer. 23

12 ssembly Instructons tep 16 lace the top/bottom 23 onto the dvder 21 as shown. Note the chamfered edges. ush cams nto the holes ndcated. rrows pontng towards the top/bottom 23. urn the cams to the rght to fx the top/bottoms chamfered edge tep 17 lace the sdes 20 onto the top/bottom 23. Not the rebates. ush cams nto the holes ndcated. rrows pontng towards the sdes. 20 urn the cams to the rght to fx the sdes rebate 12

13 ssembly Instructons tep 18 lace the back 17 nto the rebates n the sdes 20 and onto the top/bottom 23.! Important! Make sure the angle between the top and the sdes s 90 when the back s attached. Fx the back 17 to the sdes 20 and the top/bottom 23 usng nals. Use the nalholder d and a small hammer. lace the top ral 22 onto the top 23. Fx the top ral 22 onto the top 23. Fx the top ral 22 to the top 23 usng angles W and screws. 23 W W W 17 W 90.0 W tep 19 Fx the connectng plates onto the top 23 usng screws. lace the connectng plate exactly as shown. ee detals. back 3,0 cm sde 3, cm 13

14 ssembly Instructons tep 20! Warnng! he wardrobe s heavy. ft wth care. lace the 4 door wardrobe as shown. M M M M N N M M M M N N Fx t usng screws N and assembly screws M nto the holes ndcated. ee detals Fx the connectng plate to the top usng screws. tep 21 M N t s recommended that the wardrobe s fxed to the wall. Use the fttngs J. Follow the nstructon ncluded wth the ftngs. nock the shelf supports nto the holes of the sdes 1, 2, 3 and 4. lace the shelves x3 2 x3 Wallstrap and nstructon x3 x3 9 x3 x3 x3 x3 14

15 ssembly Instructons tep 22 lace the cup hnges nto the holes ndcated on the doors 14, 1 and Fx the hnges usng screws. Fx the door ral 24 to the doors 14, 1 and 18 nto the holes ndcated usng screws tep 23 ull our the drawer runners. lde the drawer onto the runners Ft and fx the lower drawer frst and work your way up. x drawer to the drawer runners usng screws H. H H H 1

16 ssembly Instructons tep 24 lde the cup hnges onto the crossplates. Fx the hnges usng the pre-mounted screws n the crossplates. ee detals. G Fx the wooden knobs G to the doors 14, 1, 18 usng screws G 18 G 1 14 G G 18 G G ghten these screws 16

17 ssembly Instructons tep 2 djustng the doors left/rght. a: o adjust the door towards the left hand sde - turn the adjustng screw to the rght. b: o adjust the door towards the rght hand sde - turn the adjustng screw to the left. djustng the doors forwards/backwards. a: oosen the fxng screw. b: ush the cup hnge/the door forwards or backwards to adjust. c: ghten the fxng screws of the crossplates. djustng the doors up/down. a: oosen the two pre-mounted screws of each crossplates, BU N as much as t wll allows the crossplates to move up and down. b: ush the door up or down to adjust. c: ghten the pre-mounted screws of crossplates. If you need help or have damaged or mssng parts, call the ustomer Helplne: Home etal Group vebury Boulevard - axon Gate West - entral Mlton eynes M9 2NW 17