Registering and/or Setting Up Your Personally-Owned Device

Transcription

1 Registering and/or Setting Up Your Personally-Owned Device On-Campus Wireless LAN Connection for Windows 10 Revised Date: November, 2018 Organization for Information Management and Communication

2 Table of Contents STEP.1: SYSTEM REQUIREMENTS FOR USE WITH KWANSEI GAKUIN NETWORK SYSTEM REQUIREMENTS APPLICATION PROCEDURES BEFORE CONFIGURING YOUR DEVICE DEVICE SECURITY AND VIRUS PREVENTION... 2 STEP.2: HOW TO APPLY TO THE ORGANIZATION FOR INFORMATION MANAGEMENT AND COMMUNICATION CHECKING YOUR PRESENT SETTINGS AND ADDING DNS SUFFIXES ADDING DNS SUFFIXES CONNECTION TO THE APLICATION SYSTEM FOR CAMPUS NETWORK CONNECTION (SSID = KG-JOIN) REGISTERING APPLICATION TO THE APPLICATION SYSTEM REMOVE A REGISTERED DEVICE FROM THE APPLICATION SYSTEM CANCELL THE REGISTRATION ON THE APPLICATION SYSTEM CONNECTION TO THE WIRELSS LAN NETWORK SSID=KGU-WLAN PROXY SETTINGS WHEN ACCESSING THE INTERNET FROM AN OFF-CAMPUS LOCATION STEP.3: HOW TO MAP NETWORK DRIVES SHARED ONLINE DATA STORAGE (DRIVES Y, M, Q AND X) YOUR PERSONAL ONLINE DATA STORAGE (DRIVE Z) SETTING UP SHARED ONLINE DATA STORAGE (Y, M, Q, AND X) SETTING UP YOUR PERSONAL ONLINE DATA STORAGE (DRIVE Z) STEP.4: ENDING A SESSION OTHER: PRINTER SETTINGS TROUBLESHOOTING... 36

3 STEP.1: SYSTEM REQUIREMENTS FOR USE WITH KWANSEI GAKUIN NETWORK 1.1 SYSTEM REQUIREMENTS Operating System Requirements: Windows 7 (service pack 1 and later) Mac OS X (10.7 and later) ios (iphone, ipod touch, ipad, ipad mini) Network Connection Requirements: Wireless LAN adaptor system that is compliant with one of IEEE b/g/n and supports 802.1x authentication and WPA2-AES encryption scheme. Note: If your device is not built in wireless connectivity, then you will need a wireless adaptor separately. A password and User ID provided by the University Organization for Information Management and Communication. 1.2 APPLICATION PROCEDURES Register your device via our application system for the university network on-campus. Necessary Procedures: 1. Connect the device which you want to register to the network on-campus, then register your device via the application system. 2. A confirmation will be sent to your Kwansei account. 3. Once an approval is sent to your Kwansei account, the registration will be done. Conditions of Approval: You will be able to apply only from the device which you wish to register. An applicant himself/herself only can apply. You will be able to access the application system only in range of a Wi-Fi base. Note: As for the wireless LAN locations, refer to Organization for Information Management and Communication s Web site > in English > User's Guide> Network > 学内ネットワークの利用について. You can access to the application system only using a wireless device. When you register wired LAN interface only, download an Excel based application form from the site below, fill it out, and send it to ipaddress@kwansei.ac.jp as attached file, using your Kwansei account. 1

4 Supported Browsers for Each Operating System on Which the Application System Can Run: Windows 7 Internet Explorer 11, Chrome 48, Firefox 44 Windows 8.1 Internet Explorer 11 Windows 10 Edge Mac OS X (El Capitan) Safari 9 ios 10 Safari BEFORE CONFIGURING YOUR DEVICE When you configure your device for use on the university network, it may change your previous configuration. If it does, you may have trouble when you return to your previous network. Please, therefore, take accurate notes of your non-school system settings BEFORE changing the settings so that you can re-create your network without any problems. We assume no responsibility whatever for any troubles resulting from the use of this manual, such as having problems connecting to your previous network. 1.4 DEVICE SECURITY AND VIRUS PREVENTION Please be sure to take at least the following steps in doing your part to maintain University Network security. Install appropriate anti-virus software on your device. Download the latest virus definition files and keep anti-virus software up to date. Update the software on a regular basis. Regular Windows Updates are also essential. Note: Check for expiration dates on your antivirus to insure that your virus prevention software is actually functioning. If University Network security detects that your device has a virus, your connection with the university system will be automatically severed. 2

5 STEP.2: HOW TO APPLY TO THE ORGANIZATION FOR INFORMATION MANAGEMENT AND COMMUNICATION Checking Your Present Settings and Adding DNS Suffixes 2.1 CHECKING YOUR PRESENT SETTINGS AND ADDING DNS SUFFIXES Login to your device with an administrator account and configure the following settings. Make sure a wireless LAN switch is ON. Click the search box displayed at left bottom in the task bar and enter Control Panel. Click on the Control Panel displayed at top of the search box. 3

6 The Control Panel will appear. Click on View network status and tasks under Network and Internet. The Network and Sharing Center will appear. Click on Change adapter settings at the left side column. The Network Connections window will appear. Right click on Wi-Fi and select Properties from the list. 4

7 The Wi-Fi Properties dialog box will appear. In the Networking tab, select Internet Protocol Version 4 (TCP/IPv4). Then click the Properties button. Internet Protocol Version 4 (TCP/IPv4) Properties dialog box will appear. If the following two radio buttons are already selected, go to 2.2 ADDING DNS SUFFIXES for further instruction. Obtain an IP address automatically Obtain DNS server address automatically 5

8 If selected is Use the following IP address and/or Use the following DNS server addresses and some numbers are typed as shown in the left, write them down. You may need the information in your other network environment. After making a record of all your present configurations, select Obtain an IP address automatically. Also select Obtain DNS server address automatically. Alternate Configuration tab will be shown. Select the tab. Select the User configured and re-enter your personal settings. (These are the settings for which you made a memo of these settings prior to beginning the configuration process.) Uncheck Validate settings, if changed, upon exit. Note: When you have your original settings stored in the Alternate Configuration tab, the set-ups you need for both on- and off-campus operation will be maintained. After input for every item is completed, click the General tab and go to 2.2 ADDING DNS SUFFIXES 6

9 2.2 ADDING DNS SUFFIXES In the General tab, click the Advanced...button. The Advanced TCP/IP Settings dialog box will appear. Click the DNS tab. 7

10 Select Append these DNS suffixes (in order): Click the Add... button. The TCP/IP Domain Suffix dialog box will appear. In the dialog, type kwansei.ac.jp. Click the Add button. The Advanced TCP/IP Settings dialog box will appear again. Click the Add button. In the TCP/IP Domain Suffix dialog, type nuc.kwansei.ac.jp. Click the Add button. Note: If you skip these steps (of adding the DNS suffixes), you might have a trouble in mapping network drives. 8

11 You will see the following two DNS suffixes displayed beneath the heading Append these DNS suffixes (in order): kwansei.ac.jp nuc.kwansei.ac.jp In the box labeled DNS suffix for this connection: type kwansei.ac.jp. Uncheck Register this connection s addresses in DNS. Click the OK button. Click the OK button to close the Internet Protocol Version 4 (TCP/IPv4) Properties dialog. Click either the OK or the Close button to close the Wi-Fi Properties dialog. 9

12 2.3 CONNECTION TO THE APLICATION SYSTEM FOR CAMPUS NETWORK CONNECTION (SSID = KG-JOIN) Click the search box displayed at the bottom left in the task bar and enter Control Panel. Click on the Control Panel displayed at the top of the search box. The Control Panel will appear. Click on Network and Internet. 10

13 The Network and Sharing Center window will appear. Click Set up a new connection or network. Choose a connection option window will appear. Select Manually connect to a wireless network. Click the Next button. A window labeled Enter information for the wireless network you want to add will appear. In the box labeled Network name:, type in KG-JOIN. From the drop down list next to Security type:, select WPA-2 Enterprise. Uncheck Start this connection automatically. Check Connect even if the network is not broadcasting. Click the Next button. Note: Please be aware that if you check [Start this connection automatically], your device may be automatically connected even when the connection is not necessary. 11

14 When the following message appears: Successfully added KG-JOIN, click Change connection settings. The KG-JOIN Wireless Network Properties dialog box will appear. Select the Security tab. Click the Settings button. 12

15 The Protected EAP Properties window will appear. Uncheck Verify the server s identity by validating the certificate. Click the Configure...button. The EAP MSCHAPv2 Properties dialog box will appear. Make sure the checkbox for Automatically use my Windows log-on name and password (and domain if any) is unchecked. Click the OK button. Close the Protected EAP Properties dialog box by clicking the OK button. 13

16 The active windows will now be the KG-JOIN Wireless Network Properties dialog box, click the Advanced settings. In the Advanced settings dialog box, check Specify authentication mode: and select User authentication. Close the dialog box by clicking the OK button. Close any remaining open window by clicking either the OK or the Close button on each window. Your system may not be correctly configured until the device is rebooted. Restart your device to initiate the new settings. Click the Network icon on the right side of the taskbar. 14

17 Select KG-JOIN from the network list and click the Connect button. The Windows Security dialog box will appear. In the box labeled User name, type in kwansei [include here your KWANSEI User ID]. In the box labeled Password, enter [your KWANSEI password]. Click the OK button. Note: Use the same User ID and password that you use to log in to the Information System Web service. Click the OK button. Note: If the Authentication dialog shows up again after clicking on OK, the ID and/or password you typed may be incorrect. Please enter your information again. 15

18 2.4 REGISTERING APPLICATION TO THE APPLICATION SYSTEM Use a browser, remaining connected to "KG-JOIN" to register the application. We recommend using the standard browser of the operation system. Open the browser. Screen of the application system for campus connection will appear automatically. If the screen doesn t appear, type in " in the address bar and press Enter. The setting page of Firefox Note: When the webpage which you are setting as homepage is unencrypted such as the browser will be automatically transferred to the application system. But if the webpage is encrypted such as then you will get certificates error or timeout error, and the login screen will not appear automatically. Note: If you use Firefox and are checking Query OCSP responder servers to confirm the current validity of certificates, it will take 15~30 seconds for the login page to appear. The following is the way to open the settings page in Firefox. Click Tool > Option. (Or click the three line menu icon on the upper right then Option.) Select Advanced on the left side. In the Certificates tab, there is the checkbox: "Query OCSP responder servers to confirm the current validity of certificates". (Initial setting is checked.) 16

19 In the case you can't access the page, try the following methods. Double check if the URL in the address bar is correct. Double check if the proxy setting is correct. Uncheck Use a proxy server for your LAN or set up the proxy using "proxy.kwansei.ac.jp:8080". Note: See 3.2 PROXY SETTINGS. Double check if your network setting is correct. Note: See 2.3 CONNECTION TO THE APLICATION SYSTEM FOR CAMPUS NETWORK CONNECTION (SSID = KG- JOIN) In the case a page like the left picture is displayed Go to the webpage from [More information]- [Go on to the webpage (not recommeded)] Application system for campus connection will appear. In the box labeled ID, type in kwansei [include here your KWANSEI User ID]. In the box labeled Password, enter your KWANSEI password. Click the Login button. Note: Our system supports Japanese and English. Click English when you want to change to the language. 17

20 Click the New Application button on the upper left The application screen will appear. Note: On failure to retrieve your MAC address, inadequacy may exist in settings of 2.1 CHECKING YOUR PRESENT SETTINGS or 2.3 CONNECTION TO THE APLICATION SYSTEM FOR CAMPUS NETWORK CONNECTION (SSID = KG- JOIN). Check your settings again. [Explanation of each display item] Applicant ID Your KWANSEI User ID will be automatically displayed. Double check if the displayed ID is yours. MAC Address The MAC address of your device will be automatically displayed. Name Your name will be automatically displayed. Double check if it is yours. 18

21 [Explanation of each input item] 1 1 Device maker s name:required item (Within 256 characters) Select the maker s name of your own device. If there is no corresponding maker s 2 name in the list, select Others and type maker s name. 3 2 Device model name :Required item (Within 256 characters) (Ex.) HP Elite, Pavilion etc. TOSHIBA dynabook etc. 4 NEC LAVIE etc. Lenovo Xseries, Vseriers etc. Apple MacBook Air, MacBook Pro etc. Apple(iOS) ipad Pro, ipad Air2 etc. If you do not know type unknown 3 OS name and version:required item (Within 256 characters) Select Operation system name and version of your owned device. If there is no corresponding Operation system name in the list, select Others and type the Operation system name and its version. (Ex.)Android (option) Wired interface s MAC address :Optional(Within 256 characters) Note:If you use only wireless LAN, you do not need to fill in. When you use a wired connection on the same device, you need to type its MAC address. Enter the Mac address with 12 characters without '-' (hyphen), ':' (colon), or any space. Note: If you don t know the MAC address, refer to How to find the MAC address of your computer ( rk_macaddress_[en] pdf ) 19

22 Once you enter all required fields, click the Apply button at the bottom of the page. A browser confirmation dialog will appear. Click the OK button Once a series of application process is completed, it will bring back to the top page. The message "Operation succeeded, <MAC address of your device> was applied" will appear. The device you applied for will be displayed in the list at the center of the screen and the status will be "Unapproved". We will review it by the next working day and notify you through the Kwansei Gakuin . The faculty and the staff can register up to 6 devices and the others up to 3. When you register both Wireless LAN and Wired, that counts as two devices. If you are one of the faculty or the staff, and add or change devices, reduce the number of devices that appears in the list to 4 or less, and the others to 1. When you replace the device due to device failure and so on, delete the old device and apply for a new one. When you apply for a device and get the message "The same MAC address already exists", the device is already registered. Confirm the application content. If you want to edit it, delete the application first and re-apply. Refer to "2.5 REMOVE A REGISTERED DEVICE FROM THE APPLICATION SYSTEM" about the way of deleting a device from the list. 20

23 2.5 REMOVE A REGISTERED DEVICE FROM THE APPLICATION SYSTEM Note: Refer to 2.4 REGISTERING YOUR DEVICE WITH THE APPLICATION SYSTEM" to see how to log in to the application system. Note: You cannot edit the content of the approved device, but delete. Note: When you apply for wired LAN interface as well as wireless at the same time, two MAC addresses are entered with the same maker, model, and OS. When both are not necessary, delete them. Note: If you don t know which MAC address you should delete, see "How to find the MAC address of your computer" html To delete a registered device from the list, click Edit in the top page. The content of your registered device will appear. Make sure that the information is one of the device which you are to delete, then click Delete. The confirmation dialog will appear. Click the OK button When the message "Delete processing of a terminal account was carried out" appears in the top page and the device information is deleted from the list, the process is now completed. Note: When you delete your registered information, no confirmation will be sent. 21

24 2.6 CANCELL THE REGISTRATION ON THE APPLICATION SYSTEM Note: Refer to 2.4 REGISTERING YOUR DEVICE WITH THE APPLICATION SYSTEM" to see how to log in to the application system. To cancel your application prior to the approval, click Edit in the top page. Click the Cancel button at the bottom of the page and click the OK button on the browser confirmation dialog. Note: Even if you want to apply for your device again, do not click the Register button here. In that case, register a new application again after you cancel the previous one. The message "Canceled your application" will appear, then the device under application will be deleted from the list. Also, a cancellation confirmation will be sent. Register a new application again as needed. 22

25 2.7 CONNECTION TO THE WIRELSS LAN NETWORK SSID=KGU-WLAN NOTE: Configure the following settings AFTER you receive a confirmation . (You won t be able to set up when the status is Unapproved".) Click the search box displayed at the bottom left in the task bar and enter Control Panel. Click on the Control Panel displayed at the top of the search box. The Control Panel will appear. Click on Network and Internet. 23

26 Choose a connection option window will appear. Select Manually connect to a wireless network. Click the Next button. A window labeled Enter information for the wireless network you want to add will appear. In the box labeled Network name:, type in KGU-WLAN. From the drop down list next to Security type:, select WPA-2 Enterprise. Check Start this connection automatically. Check Connect even if the network is not broadcasting. Click the Next button after input for every item is completed. If you completed all the previous steps correctly, the following message will appear: Successfully added KGU- WLAN. Click Change connection settings. 24

27 The KGU-WLAN Wireless Network Properties dialog box will appear. Select the Security tab. Click the Settings button. The Protected EAP Properties window will appear. Uncheck Verify the server s identity by validating the certificate. Click the Configure...button. 25

28 The EAP MSCHAPv2 Properties dialog box will appear. Make sure the checkbox for Automatically use my Windows log-on name and password (and domain if any) is unchecked. Click the OK button. Close the Protected EAP Properties dialog box by clicking the OK button. In the KGU-WLAN Wireless Network Properties dialog box, click the Advanced settings. 26

29 In the Advanced settings dialog box, check Specify authentication mode: and select User authentication. Close the dialog box by clicking the OK button. Close any remaining open window by clicking either the OK or the Close button on each window. Your system may not be correctly configured until the device is rebooted. Restart your device to initiate the new settings. Click the Network icon on the right side of the taskbar. Select KGU-WLAN from the network list and click Connect. 27

30 The Windows Security dialog box will appear. In the box labeled User name, type in kwansei [include here your KWANSEI User ID]. In the box labeled Password, enter [your KWANSEI password]. Note: Use the same User ID and password that you use to log in to the Information System Web service. Click the OK button. Please give the computer a few moments to connect to the network. Note: If the Authentication dialog shows up again after clicking on OK, the ID and/or password you typed may be incorrect. Please enter your information again. 2.8 PROXY SETTINGS After successfully setting up the network, move on to the Proxy set up. You will need to configure the proxy server settings to access external website from the internal network. Note: Below is the proxy set up procedure for Internet Explorer 11. Windows 10 comes with Microsoft Edge as default web browser but we cannot guarantee if it properly runs in our web system. Click the Start button then select Settings. 28

31 Click Network and Internet. Under Network and Internet, click Proxy in the left pane. Scroll down to Manual proxy Setup. Setup each item as below. Turn on Use a proxy Server. In the box labeled Address: type in [Proxy Address]. In the box labeled Port: type in [Port Number]. Information of Proxy Server Address For the Nishinomiya Uegahara, Nishinomiya Seiwa, Osaka Umeda campus: Address [proxy.kwansei.ac.jp] Port [8080] 29

32 For the Kobe Sanda campus: Address [proxy.ksc.kwansei.ac.jp] Port [8080] Check Don t use the proxy server for local (intranet) addresses. Click the Save button. When you can access and see external websites such as Yahoo, Google, and so on, you have configured everything properly. If you cannot access any outside website but your proxy settings can be wrong. Please check the settings again. 2.9 WHEN ACCESSING THE INTERNET FROM AN OFF-CAMPUS LOCATION It is important to note that the internet configuration described in this manual only applies to on-campus operation. When you are off-campus, uncheck the box labeled Use a proxy server for your LAN. Also, re-check this box before you are to access the school network from on-campus. STEP.3: HOW TO MAP NETWORK DRIVES The university provides data storage for all users and personal folders dedicated to each user. Note: Users can access shared folders and personal folders only from on-campus. For off-campus access, log on to Information System Web Service ( first. Then click the drive name you wish to open under Web Folder. 3.1 SHARED ONLINE DATA STORAGE (DRIVES Y, M, Q AND X) The university provides data storage, such as Drive Y, M, Q, and X where all users can access from on-campus. Drive Y Data Storage for Teaching Materials Housed at the Nishinomiya Uegahara Campus. All users can download data and execute programs in Drive Y. As for the Teachers folder, the faculty only can upload and delete data in the folder. 30

33 Drive M Data Storage for Teaching Materials Housed at the Kobe Sanda Campus. All users can download data and execute programs in Drive M, while the faculty and the staff only can upload and delete data in the drive. Drive Q Data Storage for Teaching Materials Housed at the Nishinomiya Seiwa Campus. All users can download data and execute programs in Drive Q, while the faculty only can upload and delete data in the drive. Drive X Temporary Storage for Shared Data Any user can download data, execute programs, upload and delete data in the drive. The System Administrator reserves the right to delete documents as necessary, throughout the year, especially at the end of both the spring and fall semesters. 3.2 YOUR PERSONAL ONLINE DATA STORAGE (DRIVE Z) The university provides another online data storage, Drive Z, for users to store their personal documents. Drive Z is referred to as My Documents on all classroom computers operated by the university. The Drive Z (My Document) is given to each user for his/her private use. Therefore, another user will not be able to access your Drive Z (My Document) Backing up your files to Drive Z is recommended for the following reasons: Even when your personally owned device crushes, from another device you can access Drive Z and retrieve your data you backed up on it. Drive Z can be accessed from off-campus through the internet using your Web Folder. 3.3 SETTING UP SHARED ONLINE DATA STORAGE (Y, M, Q, AND X) 31

34 Click the Start button then select File Explore. Or click File Explorer in the task bar. Right click on This PC in the left pane. Select Map network drive from the context menu. Choose a drive letter from the dropdown list located next to the Drive:. In the Folder: box, type the path of the folder to map. Make sure the checkbox Reconnect at sign-in is checked. Click the Finish button. Mapping Drive Y Drive:[Y] Folder:[ kgs file y] Mapping Drive M Drive:[M] Folder:[ kgs file m] Mapping Drive Q Drive:[Q] Folder: [ kgs file q] Mapping Drive X 32

35 Drive: [X] Folder: [ kgs file x] The Windows Security dialog box will appear. In the box labeled User name, type in kwansei [include here your KWANSEI User ID]. In the box labeled Password, enter [your KWANSEI password]. Check the box next to Remember my credentials. Click the OK button. 33

36 3.4 SETTING UP YOUR PERSONAL ONLINE DATA STORAGE (DRIVE Z) Click the Start button then select File Explore. Or click File Explorer in the task bar. Right click on This PC in the left pane. Select Map network drive from the context menu. Map your Network Drive Z as follows: Select Z from the dropdown list next to the Drive: In the box labeled Folder:, type in kgs file z [include here your KWANSEI User ID]. (For instance, if your User ID is abc12345 type in kgs file z abc12345.) Make sure the checkbox for Reconnect at sign-in is checked. Click the Finish button. 34

37 The Windows Security dialog box will appear. In the box labeled User name, type in kwansei [include here your KWANSEI User ID]. In the box labeled Password, enter [your KWANSEI password]. Check the box next to Remember my credentials. Click the OK button. STEP.4: ENDING A SESSION The only thing you have to do to sign off from the network is to turn off your computer. Once you have completed your set up, your device will stay configured for continuing use with the school network. Note: If your device is not connected to the network in the next use, disable your wireless LAN adapter temporarily. Then enable the adapter. An authentication dialog will appear again. Click this and enter your KWANSEI user name and password. OTHER: PRINTER SETTINGS As for the printer settings, refer to Information System Web Service ( In English >User's Guide >Print > How to Use Printer System 35

38 TROUBLESHOOTING If you have trouble getting a wireless network connection, you should check the following: Is the wireless switch turned on? Make sure it is turned on. Is the wireless adapter enabled? 1. Right click on the Network icon, on the right side of the taskbar. Then click Open Network and Sharing Center. 2. In the left pane of the Network and Sharing Center window, select Change adapter settings. 3. If Wireless Network Connection is grayed out and shown as Disabled, right click on the icon and select Enable this network device from the list. Is the combination of user ID and password correct? If a Windows Security dialog shows up after entering your user ID and password, there is a possibility that you may enter incorrect information and authentication fails. Please enter your information again. Is the wireless network properly connected to KGU-WLAN? If the Network icon is shown as below, you are not connected to the Local university network. Click the Network icon, select KGU-WLAN and click the Connect button. Make sure Connect automatically is checked. If KGU-WLAN is not displayed, it means that you are not in range of a Wi-Fi base station. An authentication dialog will show up. Please type your KWANSEI user ID and Password and click the OK button. 36

39 Have you changed proxy settings in your browser? When you cannot access external websites such as Yahoo! or Google from within the internal KWANSEI network, please check your 2.8 PROXY SETTINGS. Note: The proxy setting may vary according to your browser. If you used your device to connect to the internet outside of the campus, Use a proxy server may be turned off. If so, turn it on. Have you tried rebooting your device? The configuration may not reflect the changes yet. Restart your device so that the change in configuration takes effect. Won t your device connect to the Internet suddenly? Disable your wireless LAN adapter temporarily then enable the adapter. 1. Right click on the Network icon, on the right side of the taskbar. Then click Open Network and Sharing Center. 2. In the left pane of the Network and Sharing Center window, select Change adapter settings. 3. Disable the Wi-Fi adapter. 4. Re-enable the Wi-Fi adapter. 37

40 Still need help? Feel free to contact us at the following locations: Campus Tech Support Center Nishinomiya Lecture Hall 4 PC Support Center Uegahara Campus 第 4 別館 PC サポート室 (ex: ) 西宮上ケ原キャンパ Media and Research Facilities Building PC Support ス Center 2 メディア 研究棟第 2PC サポート室 (ex: ) Graduate Students Services Building 1 PC Support Center 3 大学院 1 号館第 3PC サポート室 (ex: ) Kobe Sanda Campus 神戸三田キャンパス Nishinomiya Seiwa Campus 西宮聖和キャンパス Osaka Umeda Campus 大阪梅田キャンパス Building Ⅵ (third floor) The PC consultation counter Ⅵ 号館 PC 利用相談カウンター (ex: ) Building 6 Information media Office, Nishinomiya- Seiwa Branch (IT Support Desk) 6 号館情報メディア室 (PC サポート室 )(ex: ) Campus Office (14th floor) The Reception counter 14 階事務室受付カウンター (ex:63-25) 38