Using the brackets as a guide, mark hole locations and then pre-drill holes for the screws.

Transcription

1 Sivoia QS Wirlss Cllular English. Motorizd shad with wirlss radio frquncy (RF) Installation Guid (plas rad bfor installing) Option : Outsid Mount Trim: Install Mounting Brackts Using th brackts as a guid, mark hol locations and thn pr-drill hols for th scrws.. Stp : Rviw includd componnts: Bfor you bgin, opn th box and mak sur you hav all th ncssary parts: th shad, mounting brackts, and scrws. Includd: You will also nd a cordlss drill, a / inch drill bit, a # Phillips bit, a pncil, a tap masur, and or 6 D alkalin battris (dpnding on th shad s siz) if you purchasd a battry-powrd shad. Cllular shad Mounting brackts Drill bits Tap masur Pncil # Phillips scrwdrivr Window fram Brackt. Plug-in powr supply If th shad is widr than 7 inchs, you will nd to install a third ( ) and a fourth brackt ( ). Install ach of ths on-third of th way in from th outr brackts. Sid viw Powr panl Your shad was manufacturd according to th mounting option you chos whn ordring your shad. Mak sur you follow th appropriat mounting instructions: Opt. insid mount, Opt. outsid mount on trim, or Opt. outsid mount abov trim. Mak sur th brackts ar alignd with ach othr. (If not, th shad may not oprat proprly.)..5 Option : Insid Mount: Installing Mounting Brackts For th bst RF rang, rposition th antnna holdr. Unsnap th antnna holdr from th hadrail. Hold th shad up to th window to mak sur it s th corrct siz. Antnna holdr as shippd Sid viw. Us a pncil to mark whr you will nd to install th mounting brackts. If you r installing an insid mount shad, align th brackts with th front dg of th window trim, inchs in from ach sid of th window. NOTE: s widr than 5 inchs (vinyl hadrail) or 8 inchs (aluminum hadrail) will nd a third brackt ( ). Install this brackt inchs to th lft of th driv (th box in th middl of th hadrail). in Antnna holdr rpositiond in Driv Top viw of shad widr than 5 inchs or 8 inchs / / / Top viw of shad widr than 7 inchs Align th top of th brackts with th top of th trim. Using th brackts as a guid, mark hol locations and thn pr-drill hols for th scrws. Install th mounting brackts using th providd scrws. Plac ach brackt flush against th trim (using spacrs bhind brackts if ndd) and using th cordlss drill, driv ach scrw through th hols in th brackt. Brackt Spacr Wall Sid viw Driv in /.6 / / Top viw of shad widr than 7 inchs /0 LUTRON Elctronics Co., Inc. P/N REV. C Top viw Top viw of shad widr than 5 inchs or 8 inchs If th shad is widr than 7 inchs, you will nd to install a third ( ) and a fourth brackt ( ). Install ach of ths on-third of th way in from th outr brackts. in in in Top viw. Mov it out to th oprating position bhind th hadrail, and snap it into plac. Thn us a pncil to mark whr you ll nd to install th mounting brackts, inchs in from th marks you mad in stp.. NOTE: s widr than 5 inchs (vinyl hadrail) or 8 inchs (aluminum hadrail) will nd a third brackt ( ). Install this brackt inchs to th lft of th driv (th box in th middl of th hadrail). Rchargabl battris Stp : Installing Mounting Brackts. Install th mounting brackts, using th providd scrws. Plac ach brackt flush against th front of th window fram and, using th cordlss drill, driv ach scrw through th hols in th top of th brackt. Othr Powr Options: Battris: 6D. Tools rquird: Cordlss drill D #6 Phillips mounting scrws Hold th shad up to th window to mak sur it s th corrct siz. Cntr th shad and us a pncil to mark th trim at ach nd of th shad. Install th shad in th brackts. Holding th shad in both hands, tilt th top of th shad slightly away from you and hook th front dg into th brackts bhind th battry rlas tabs. Thn gntly tilt th shad down and prss th bottom of th hadrail until you har it click into plac. B sur not to catch any fabric clls in th brackts. Hook front dg Window trim Prss shad Sid viw Optional (not includd) NOTE: If window trim is angld, or not lvl vrtically, plac an angld spacr (not includd) bhind ach brackt. Ensur that th shad is lvl bfor placing th brackt flush against th trim. Pr-drill a hol through th spacr as wll. Click Sid viw.5 Rfr to stps.5 and.6 to xtnd th antnna holdr and install th shad in th brackts. Mak sur th brackts ar alignd with ach othr. (If not, th shad may not oprat proprly.)

2 Option : Outsid Mount Abov Trim: Installing Mounting Brackts. Hold th shad up to th window to mak sur it s th corrct siz. Cntr th shad and us a pncil to mark th trim at ach nd of th shad..6. Us a pncil to mark whr you will nd to install th mounting brackts, inchs in from th marks you mad in stp.. NOTE: s widr than 5 inchs (vinyl hadrail) or 8 inchs (aluminum hadrail) will nd a third brackt ( ). Install this brackt inchs to th lft of th driv (th box in th middl of th hadrail). If th shad is widr than 7 inchs, you will nd to install a third ( ) and a fourth brackt ( ). Install ach of ths on-third of th way in from th outr brackts.. in / / Stp B: Attaching Powr Supply If you hav a shad that uss th plug-in powr supply, attaching th powr supply is simpl. Prss both Rmov and battry rplacrlas all tabs Rmov and rplac all (PUSH) abov th hadrail. Th shad battris from ach tray battris from ach tray will tilt forward, xposing th Prss buttons powr abov cabl. hadrail to xpos battris Uncoil th cabl and plug it into th plug-in powr supply. Install th battris as indicatd in th battris from ach tray battry trays (so th /Rmov signs and rplac all match). Mak sur th battris ar D xampl shown fully insrtd in th trays. call to spak to a customr srvic rprsntativ visit: or To viw instructional vido on how to rplac battris plas Grasp th hadrail with both hands and tilt it back into th brackts, prssing gntly until you har a click. For bst battry lif, don t mix old and nw battris, us only D-siz alkalin battris, and don t mix battry typs or us carbon-zinc battris. Also, don t us rchargabl battris. Using th brackts as a guid, mark hol locations and thn pr-drill hols for th scrws. Plac a spacr bhind ach brackt (to nsur that th shad clars th window trim). Thn plac th brackt flush against th spacr and th wall, aligning th hols. Driv a scrw through th hols in th brackt and through th spacr. Prss shad click Plug th plug-in powr supply into an outlt. Your shad is now powrd! To rplacto thrplac battris, prss th To rplac battry rlas tabs locatd abov battris battris th shad hadrail. Th hadrail Prss buttons abov will tilt forward, xposing th hadrail to xpos battris battris insid of it. Tilt shad c all th battris ar in plac, th LED indicator light will flash brifly..5 To rplac Prss th battry rlas tabs (PUSH) battris battris abov th hadrail. Th shad Prss buttons abov will tilt forward, xposing th battry trays. hadrail to xpos battris hadrail to xpos battris buttons abov battris To rplac Sid viw / Prss Top viw of shad widr than 7 inchs Aftr using your marks to plac th brackts against th wall, align th top of th brackts with ach othr and mark thir location, making sur thy ar lvl. Rfr to stps.5 and.6 to xtnd th antnna holdr and install th shad in th brackts. To rplac Top viw of shad widr than 5 inchs or 8 inchs Prss shad click If you hav a battry-powrd shad, installing and rplacing th battris is a snap. Sivoia QS Wirlss cllular shads us TriathlonTM powr tchnology to achiv a typical battry lif of yars. Lutron rcommnds only alkalin battris. Driv Tilt shad Stp A: Installing and Rplacing Battris in l r P H. in Grasp th hadrail with both hands and tilt it back into th brackts, prssing gntly until you har a click. 5 Mak sur you ar scrwing into wood studs. If you r not mounting th brackts into wood studs, you ll nd to us appropriat fastnrs for th mounting surfac (not includd). Mak sur th brackts ar alignd with ach othr. (If not, th shad may not oprat proprly.) Sid viw Rmov and rplac all Rmov and rplac all battris from ach tray battris from ach tray Prss buttons abov Stp : Programming hadrail to xpos battris c you v installd your Sivoia QS Wirlss cllular shad, you will nd to program it. If you ar using your shad in a standalon systm, you will nd to assign your so that it works with th shad. Rfr to th following pag for programming dtails. brackt spacr wall window fram Sid viw /0 LUTRON Elctronics Co., Inc. P/N REV. C Rmov all of th battris from ach sid of th tray, bginning with th battry that s closst to th middl of th hadrail. Aftr you hav takn that battry out, slid th nxt battry ovr and rmov it. Now you can insrt th nw battris, following stps and abov. If you ar working with a RadioRA systm, us th RadioRA Essntials or Inclusiv softwar to st up your shad. -yar battry lif basd on up and down movmnts pr day assuming a ft. wid by 5 ft. tall shad using light-filtring fabric. Battry lif can vary btwn to 5 yars dpnding on shad siz and fabric slction. If you don t hav RadioRA dsign and programming softwar, rfr to th RadioRA stup guid for instructions. Th guid is availabl at If you ar working with a HomWorks QS systm, us th HomWorks QS dsign and programming softwar to st up your shad.

3 Programming Your - Standalon Applications (s prvious pag for systm programming information) Dsird action. Put th shad into programming mod. Put th into programming mod. Assign a to th shad (Must b don bfor th shad will work). Adjust sttings Tap th shad button on all shads you want assignd Pico wirlss. Sav sttings 5. Rturn th to normal opration Hold button for about 5 sconds, until th shad You hav assignd th to th shad. stouch kypad button illuminats grn (Continu to programming in 0 sconds or lss to avoid timout) End Rsult Hold button for about 5 sconds, until th shad Not: Rpat to assign mor s. GRAFIK Ey Not: Allow hours for shad fabric to rlax bfor adjusting limits. Lowr and uppr limits ar pr-programmd basd on your window dimnsions, but may nd fin-tuning. Tap th shad button on th shad you want to st th lowr limit on. Pico wirlss Hold and Rais buttons for about 5 sconds, until th shad button blinks and rmains lit. Not: This stp is only ncssary for a Pico with an LED. Hold and Rais until th LED on th Pico turns off. Hold button for about 5 sconds, until th shad. St th shad s lowr limit Us th s Rais and Lowr buttons to adjust shad position to th lowr limit you prfr. Scrn Drap Scrn LED You hav st th shad s lowr limit. button illuminats grn (Continu to programming in 0 sconds or lss to avoid timout). S t th shad s uppr limit (optional) Tap th shad button on th shad you want to st th uppr limit on. stouch kypad Hold and Rais buttons for about 5 sconds, until th shad button blinks and rmains lit. GRAFIK Ey Pico wirlss (Continu to programming in 0 sconds or lss to avoid timout) a. St a favorit shad lvl (prst) for on shad assignd to th, or multipl shads assignd to th at th sam lvl Scrn Drap Scrn Hold button for about 5 sconds, until th shad Us th s Rais and Lowr buttons to adjust shad position to th uppr limit you prfr. Hold button for about 5 sconds, until th shad Scrn Drap Scrn Hold and Rais buttons for about 5 sconds until th shad button blinks and rmains lit. Scrn Drap Scrn Not: This stp is only ncssary for a Pico with an LED. Hold and Rais until th LED on th Pico turns off. LED stouch kypad Us th s Rais and Lowr buttons to adjust shad position to th lowr limit you prfr. Hold and Rais buttons for about 5 sconds, until th shad button blinks and rmains lit. button illuminats grn Us th s Rais and Lowr buttons to adjust shad position to th uppr limit you prfr. Hold 5 sconds, until th shad button for about Scrn Drap buttonblinks and turns off. You hav st th shad s uppr limit. Scrn GRAFIK Ey Pico wirlss Scrn Drap Scrn Us th s Rais and Lowr buttons to adjust shad position to th lvl you prfr. Scrn Drap Scrn Scrn Drap Scrn Hold Favorit button for about 5 sconds. stouch kypad Us th s Rais and Lowr buttons to adjust shad position to th lvl you prfr. Hold th button for about 5 sconds. Scrn Drap Scrn You hav st a favorit prst lvl. GRAFIK Ey Pico wirlss Us th s Rais and Lowr buttons to adjust th c shads ar at prfrrd lvl, rstor powr to all st shad s position to th lvl you prfr. Thn disconnct shads, thn hold Favorit button for about 5 sconds. th shad s powr by ithr rmoving a battry or unplugging th powr supply. Rpat for additional shads. b. St a favorit shad lvl (prst) for multipl shads assignd to th at diffrnt lvls Scrn Drap Scrn stouch kypad /0 LUTRON Elctronics Co., Inc. P/N REV. C Us th s Rais and Lowr buttons to adjust th c shads ar at prfrrd lvl, rstor powr to all st shad s position to th lvl you prfr. Thn disconnct shads, thn hold button for about 5 sconds. th shad s powr by ithr rmoving a battry or unplugging th powr supply. Rpat shads. for additional GRAFIK Ey You hav st a favorit prst lvl. If you hav any qustions rgarding programming your cllular shads plas call Lutron tch support at Our tam is availabl to hlp you hours a day, 7 days a wk.

4 Rmoving th From th Brackts To compltly rmov th shad from its brackts, first locat th mtal tab on ach brackt. Th tab is locatd whr th shad fabric mts th hadrail on th sid closst to th window. Insrt a small flathad scrwdrivr through th hol in th mtal tab so th tip of th scrwdrivr is btwn th hadrail and tab. Pull th scrwdrivr toward you until th tab rlass th hadrail. Rpat for ach brackt on th shad. c you hav rlasd all tabs, you can lift th shad off th brackts. Claning th Fabric To kp your cllular shads looking thir bst, rgularly brush thm with a fathr dustr or lightly vacuum thm with a brush-typ attachmnt. If your shads gt a spot of dirt or a stain on thm, us a clan, soft cloth and a solution of mild dtrgnt and warm watr ( part dtrgnt to parts watr) to blot or lightly rub th spot or stain. B xtra carful if you r claning a blackout fabric bcaus you could prmanntly cras th fabric. Sid viw Fathr dustr Soft cloth Vaccum clanr with brush attachmnt Dilutd mild dtrgnt Troublshooting Symptom dosn t powr up Limitd RF rang powrs up, but is not moving won t activat into a main rpatr systm Cannot assign a dirctly to th shad Solution Battry powrd shad: ) Ensur battris ar installd corrctly. ) Ensur battris ar frsh. Wird shad: ) Ensur th wirs ar proprly connctd to th driv. ) Ensur th wirs ar proprly connctd to plug-in supply or panl. Ensur antnna brackt was movd into installation position Chck th shad LED for fdback whn a command is snt to th shad. If th LED blinks, contact tch support at to rsolv th movmnt issu. If th LED dos not giv any fdback: ) Ensur th driv is powrd by prssing th button on th shad to vrify it lights up grn. ) For standalon shads, rpat assignmnt stps locatd in Stp : Programming ) For a shad activatd into a RadioRA or HomWorks QS systm, nsur th shad and ar activatd into th systm. You can chck th shad by prssing and rlasing th shad button. Th LED in systm addrssd shads will light whn you prss th button and will turn off whn you rlas it. Th LED in non-systm activatd shads will rmain lit for 0 sconds aftr you rlas it. Ensur shad is in activation mod. (Wait on minut aftr snding GUI command to ntr activation mod and chck LED fdback. LED will blink scond on, sconds off for inactivatd shads in activation mod and sconds on, scond off for activatd shads in activation mod.) Ensur shad is not assignd to a dirct (rmov by factory dfaulting). Ensur shad is not activatd into a RadioRA or HomWorks QS systm. (Chck LED fdback. Th LED in systm addrssd shads will light whn you prsss th button and will turn off whn you rlas it.) Ensur is working proprly. Symptom is moving slowly with rd LED lit fabric will not rach windowsill Low Battry Indicator Button Blink Pattrn rd blink vry 5 sconds Rd LED on whil shad is moving, thn off Rd LED is on for 5 sconds, thn off, aftr command is snt Solution Indicats that battris ar low and nd to b rplacd. Chck lowr limit stting. If adjusting lowr limit dos not fix th issu, thn allow fabric to rlax. Lav shad in closd position to allow fabric to rlax. Tim rquird to rlax may vary (up to hours). Dscription Th shad cannot mov. Battris nd to b rplacd. has only a fw motions lft. Battris nd to b rplacd. hard th button prss, but cannot mov. Battris nd to b rplacd. Rstoring th s Factory Sttings This stp will rmov any s assignd to th shad as wll as any xisting programming. It will not affct th shad s uppr and lowr limits. Tap th shad button quickly thr tims, and hold th shad button until th button blinks grn rapidly. Immdiatly tap th shad button quickly thr mor tims, until th shad button blinks grn rapidly, thn blinks rd/grn thr tims, and turns off. Also, do not us strong dtrgnts or spot rmovrs, and do not hav your shads profssionally dry cland. /0 LUTRON Elctronics Co., Inc. P/N REV. C isn t lvl Lav shad in closd position to allow fabric to rlax. Tim rquird to rlax may vary (up to hours). Contact tch support at for instructions to walk through lvling procss. (continud) For additional troublshooting hlp, visit undr Srvic and Support, Application Nots, Sivoia QS Wirlss, to viw Blink Cods for Sivoia QS Wirlss Cllular s. If you hav any qustions rgarding your cllular shads plas call Lutron tch support at Our tchnical support staff ar availabl hours a day, 7 days a wk.

5 Lutron Elctronics Co., Inc. SHADING SOLUTIONS Eight Yar Limitd Warranty WARRANTY SCOPE This limitd warranty ( Warranty ) covrs th Lutron supplid (a) SrnaTM s, (b) Sivoia Systms ( Sivoia Systms ), (c) manual shad systm and (d) altrnating currnt or a/c shad systm (ach of th forgoing bing a Systm ). Customr acknowldgs and agrs that us of th Systm constituts accptanc of all trms and conditions of this Warranty. LIMITED WARRANTY Subjct to th xclusions and rstrictions dscribd blow, Lutron warrants that ach Systm will b fr from manufacturing dfcts from th dat of shipmnt by Lutron for a priod of (a) on yar as to th wall s, intrfacs and systm accssoris of th Systm ( Extrnal Componnts ) and (b) ight yars as to th othr Systms and th lctronic driv unit, shad fabric and shad hardwar of th Systm. If any manufacturing dfct xists in th Extrnal Componnts, so long as Customr promptly notifis Lutron of th dfct within th on yar warranty priod and, if rqustd by Lutron, rturns th dfctiv part(s), Lutron will, at its option, ithr rpair th dfctiv part(s) or provid comparabl rplacmnt part(s). If any manufacturing dfct xists in any of th componnts of a Systm othr than th Extrnal Componnts, so long as Customr promptly notifis Lutron of th dfct within th ight yar warranty priod and, if rqustd by Lutron, rturns th dfctiv part(s), Lutron will, at its option, ithr rpair th dfctiv part(s) or issu a crdit to th Customr against th purchas pric of comparabl rplacmnt part(s) purchasd from Lutron as providd blow: Numbr of yars from dat of shipmnt Prcntag of cost of rplacmnt parts crditd by Lutron Up to 5 00% Mor than 5 but not mor than 8 50% Mor than 8 0% Rplacmnt parts for th Systm providd by Lutron or, at its sol discrtion, an approvd vndor may b nw, usd, rpaird, rconditiond, and/or mad by a diffrnt manufacturr. EXCLUSIONS AND RESTRICTIONS This Warranty will b void, and Lutron and its supplirs will hav no rsponsibility undr this Warranty, if Lutron or its rprsntativs cannot accss any componnts of th Systm to inspct, diagnos problms with or rpair th Systm or any of its componnts as a rsult of concalmnt or inaccssibility of such componnts within a building structur. This Warranty dos not covr, and Lutron and its supplirs ar not rsponsibl for:. Damag, malfunction or inoprability diagnosd by Lutron or a Lutron approvd third party as causd by normal war and tar, abus, misus, incorrct installation, nglct, accidnt, intrfrnc or nvironmntal factors, such as (a) us of incorrct lin voltags fuss or circuit brakrs; (b) failur to install, maintain and oprat th Systm pursuant to th oprating instructions providd by Lutron and th applicabl provisions of th National Elctrical Cod and of th Safty Standards of Undrwritr s Laboratoris; (c) us of incompatibl dvics or accssoris; (d) impropr or insufficint vntilation; () unauthorizd rpairs or adjustmnts or altrations; (f) vandalism; (g) an act of God, such as fir, lightning, flooding, tornado, arthquak, hurrican or othr problms byond Lutron s ; or (h) dirct xposur to corrosiv matrials.. -sit labor costs to diagnos issus with, and rmov, rpair, rplac, adjust, rinstall and/or rprogram th Systm or any of its componnts.. Componnts and quipmnt xtrnal to th Systm, such as, non-lutron lighting and automation systms; building wiring audio-visual quipmnt; and non-lutron tim clocks, photosnsors and motion dtctors.. Th cost of rpairing or rplacing othr proprty that is damagd whn any Systm dos not work proprly, vn if th damag was causd by th Systm. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO EIGHT YEARS FROM THE DATE OF SHIPMENT, EXCEPT THAT SUCH IMPLIED WARRANTIES ARE LIMITED TO ONE YEAR FROM THE DATE OF SHIPMENT AS TO THE EXTERNAL COMPONENTS. IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE FOR EXEMPLARY, CONSEQUENTIAL, I NCIDENTAL OR SPECIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO DAMAGES FOR PERSONAL INJURY, FAILURE TO MEET ANY DUTY, INCLUDING OF GOOD FAITH OR REASONABLE CARE, NEGLIGENCE, OR ANY OTHER LOSS WHATSOEVER), NOR FOR ANY REPAIR WORK UNDERTAKEN WITHOUT LUTRON S PRIOR WRITTEN CONSENT ARISING OUT OF OR IN ANY WAY RELATED TO THE INSTALLATION, DEINSTALLATION, USE OF OR INABILITY TO USE THE SYSTEM OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF THIS WARRANTY, EVEN IN THE EVENT OF THE FAULT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY, BREACH OF CONTRACT OR BREACH OF WARRANTY OF LUTRON OR ANY OTHER PARTY, AND EVEN IF LUTRON OR SUCH OTHER PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT LIMITATION, ALL DIRECT DAMAGES AND ALL DAMAGES LISTED ABOVE), THE ENTIRE LIABILITY OF LUTRON AND OF ALL OTHER PARTIES UNDER THIS WARRANTY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, USE, REPAIR, OR REPLACEMENT OF THE SYSTEM, AND CUSTOMER S SOLE REMEDY FOR THE FOREGOING, WILL BE LIMITED TO THE AMOUNT PAID BY CUSTOMER FOR THE SYSTEM. THE FOREGOING LIMITATIONS, EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE MAXIMUM EXTENT ALLOWED BY APPLICABLE LAW, EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. WARRANTY CLAIMS, TECHNICAL ASSISTANCE AND WARRANTY INFORMATION Contact th Lutron Tchnical Support Cntr at th numbrs providd blow or your local Lutron sals rprsntativ with qustions concrning th installation or opration of th Systm or this Warranty, or to mak a warranty claim. Plas provid th xact modl numbr whn calling. USA and Canada ( hrs/7days) (800) Othr countris (8 a.m. 8 p.m. ET) (60) Fax (60) FCC Information Not: This quipmnt has bn tstd and found to comply with th limits for a Class B digital dvic, pursuant to part 5 of th FCC ruls. Ths limits ar dsignd to provid rasonabl protction against harmful intrfrnc in a rsidntial installation. This quipmnt gnrats, uss and can radiat radio frquncy nrgy and, if not installd and usd in accordanc with th instructions, may caus harmful intrfrnc to radio and tlvision rcption, which can b dtrmind by turning th quipmnt off and on. Th usr is ncouragd to try to corrct th intrfrnc by on or mor of th following masurs: Rorint or rlocat th rciving antnna. Incras th sparation btwn th quipmnt and rcivr. Connct th quipmnt into an outlt on a circuit diffrnt from that to which th rcivr is connctd. Consult th dalr or an xprincd radio/tv tchnician for hlp. Not: Changs or modifications not xprssly approvd by Lutron Elctronics Co. could void th usr s authority to oprat this quipmnt. This dvic complis with Part 5 of th FCC Ruls. Opration is subjct to th following two conditions: () This dvic may not caus harmful intrfrnc and () This dvic must accpt any intrfrnc rcivd, including intrfrnc that may caus undsird opration. This Class B digital apparatus complis with Canadian ICES-00. Lutron Tchnical Support Contact Lutron Tchnical Support at th numbrs providd blow or your local Lutron sals rprsntativ with qustions concrning th installation or opration of th Systm or this Warranty, or to mak a warranty claim. Plas provid th xact modl numbr whn calling. Lutron, th Sunburst logo, Sivoia, stouch, RadioRA, HomWorks, and Pico ar rgistrd tradmarks of Lutron Elctronics Co., Inc. Srna is a tradmark of Lutron Elctronics Co., Inc. Worldwid Hadquartrs USA Lutron Elctronics Co., Inc. 700 Sutr Road Cooprsburg, PA USA TEL: FAX: Tchnical Support: or Toll Fr:.888.LUTRON shadinginfo@lutron.com WEB: Europ Hadquartrs Unitd Kingdom Lutron EA Ltd 6 Sovrign London, EW JF, UK TEL:.(0) FAX:.(0) Tchnical Support:.(0) FREEPHONE: Asian Hadquartrs Singapor Lutron GL Ltd 5 Ho Chiang Road #07-0 Singapor, 0896 TEL: FAX: Tchnical Support: /0 LUTRON Elctronics Co., Inc. P/N REV. C NO LUTRON AGENT, EMPLOYEE OR REPRESENTATIVE HAS ANY AUTHORITY TO BIND LUTRON TO ANY AFFIRMATION, REPRESENTATION OR WARRANTY CONCERNING THE SYSTEMS. UNLESS AN AFFIRMATION, REPRESENTATION OR WARRANTY MADE BY AN AGENT, EMPLOYEE OR REPRESENTATIVE IS SPECIFICALLY INCLUDED HEREIN, OR IN STANDARD PRINTED MATERIALS PROVIDED BY LUTRON, IT DOES NOT FORM A PART OF THE BASIS OF ANY BARGAIN BETWEEN LUTRON AND CUSTOMER AND WILL NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER. IC Information This dvic complis with Industry Canada licnc-xmpt RSS standard(s). Opration is subjct to th following two conditions: () this dvic may not caus intrfrnc, and () this dvic must accpt any intrfrnc, including intrfrnc that may caus undsird opration of th dvic.