WINDOW HINGE ORDERING NO. STEEL FIXED BRASS PIN SQUARE EDGES LEFT STEEL FIXED STEEL PIN

Transcription

1 WINDOW HINGE IP No MTERIL SURFE STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED INDUSTRY PKING IN OXES OF 100 PIEES MM MTERIL MM PIN MM PPROX. WEIGHT KG / P IP No FIG. 1 FIG USE NO TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MEHNISM WHILE TIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWIE YER. SEE LSO INSTRUTIONS ON PGE 28-2.

2 6 DOOR HINGE IP No MTERIL SURFE STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED INDUSTRY PKING IN OXES OF 0 PIEES MM MTERIL MM PIN MM PPROX. WEIGHT KG / P. IP No FIG. 1 FIG USE NO..0. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MEHNISM WHILE TIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWIE YER. SEE LSO INSTRUTIONS ON PGE 28-2.

3 7 DJUSTLE DOOR HINGE IP No MTERIL SURFE STEEL FIXED STEEL PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED INDUSTRY PKING IN OXES OF 0 PIEES MM MTERIL MM PIN MM PPROX. WEIGHT KG / P DJUSTLE HORISONTLLY ND VERTILLY RIGHT

4 8 IP No UPPER HINGE PRT LOWER HINGE PRT 26 FIG DJUSTMENT PLTE FITTING: 1. MOUNT THE DJUSTMENT PLTE IN THE GROOVE OF THE DOOR IN THE MIDDLE OF WHERE THE LOWER HINGE PRT IS EING MOUNTED. 2. PLE HINGE SO THT THE LOWER HINGE PRT IS OVER THE DJUSTMENT PLTE ND FSTEN IT. THE DJUSTMENT S SHOULD E LOOSENED FIG. 2 DJUSTMENT: VERTILLY: DJUST TO WNTED POSITION ON THE LRGE T THE OTTOM OF THE HINGE - ±3 MM. HORIZONTLLY: LOOSEN THE MOUNTING S ND DJUST TO WNTED POSITION. FSTEN THE MOUNTING S. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MEHNISM WHILE TIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWIE YER. SEE LSO INSTRUTIONS ON PGE 28-2.

5 SIDE SWING WINDOW 0 0 WITH FRITION IP No. 627 MTERIL SURFE STEEL LEFT RIGHT ELETROPLTED STNDRDPKING IN OXES OF SETS MM PPROX. WEIGHT KG / SET DJUSTLE FRITION ONVENIENT FOR LENING SWINGS 0 OPENS LER FROM URTINS ND WINDOW FRME MX. VENTILTION ONELED FITTINGS NODIZED LUMINIUM RILS TOP FITTING OTTOM FITTING 1 SET RIGHT HND FIRE-ESPE OPENING: 00 MM FROM SSH HEIGHT 726 MM

6 10 IP No FIG. 2 HORIZONTL PLN HINGE SIDE FITTING SHOWN ON FRME ILL RIGHT HND ILLUSTRTION 627 MX. SSH WEIGHT KGS 40 FIG. 1 VERTIL PLN MIN. SSH WIDTH 31 MX. SSH WIDTH 820 4,0 FIG. 3 FITTING: 1. THE FITTING SHOULD E POSITIONED IN THE GROOVES T HED ND ILL OF FRME ND ED ON (FIGURE 1 ND 2) 2. NOW PUSH THE WINDOW SSH INTO POSITION Y SSH SLOTS ND FSTEN THE S. 3. THE FRITION N NOW E DJUSTED ON THE TOP FITTING. IF LRGER OPENING IS WNTED THEN JUST MOVE THE DJUSTLE STOP FITTING IN THE TOP FRME LUMINIUM RIL. THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURITE THE PIVOT/MOVLE METL PRTS OF THE MEHNISM WHILE TIVTING REPETEDLY. HEREFTER LURITE MINIMUM TWIE YER. DO NOT LURITE THE LUMINIUM RILS. SEE LSO INSTRUTIONS ON PGE 28-2.

7 SIDE SWING WINDOW 0 0 WITH FRITION adjustable 11 MTERIL STEEL LEFT RIGHT SURFE ELETROPLTED STNDRD PKING IN OXES OF SETS , MM WEIGHT PPROX. KG / SET DJUSTLE FRITION ONVENIENT FOR LENING SWINGS 0 OPENS LER FROM URTINS ND WINDOW FRME MX. VENTILTION ONELED FITTINGS NODIZED LUMINIUM RILS TOP FITTING OTTOM FITTING FIRE-ESPE OPENING IP NR. 6276: 00 MM FROM SSH HEIGHT 706 MM 1 SET RIGHT FIRE-ESPE OPENING IP NR. 6277: 00 MM FROM SSH HEIGHT 70 MM 600 MM FROM SSH HEIGHT 8 MM

8 EENTRI FITTING SHOWN ON TOP FRME ILL - RIGHT HND ILLUSTRTION 2. DJUSTMENT PLTE MRK HINGE SIDE. FIG. 2 HORIZONTL PLN FITTING SHOWN ON OTTOM FRME ILL - RIGHT HND ILLUSTRTION HINGE SIDE FITTING: FIG. 1 VERTIL PLN MX. SSH WEIGHT KGS MIN. SSH WIDTH MX. SSH WIDTH FIG THE FITTING SHOULD E POSITIONED IN THE GROOVES T HED ND ILL OF FRME ND ED ON (FIGURE 1 ND 2) 2. NOW PUSH THE WINDOW SSH INTO POSITION Y SSH SLOTS ND FSTEN THE S. 3. THE FRITION N NOW E DJUSTED ON THE TOP FITTING. IF LRGER OPENING IS WNTED THEN JUST MOVE THE DJUSTLE STOP FITTING IN THE TOP FRME LUMINIUM RIL. 4. THE SSH N E DJUSTED ±1. MM SIDEWYS. EFORE NY DJUSTMENT THE MOUNTING IN THE DJUSTMENT PLTE IN THE TOP OF THE FRME HVE TO E LOOSENED. THEN DJUST Y USING TORX-20 KEY TO TURN THE EENTRI. Y DELIVERY THE MRK ON THE EENTRI IS IN 0 0 POSITION OMPRED TO THE FITTING, WHIH INDITING THE 0-POSITION. THE EENTRI N E TURNED 0 0 TO EH SIDE, WHIH GIVES THE MXIMUM DJUSTMENT OF 1½ MM. FTER THE DJUSTMENT THE MOUNTING IN THE DJUSTMENT PLTE IS FSTENED. THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURITE THE PIVOT/MOVLE METL PRTS OF THE MEHNISM WHILE TIVTING REPETEDLY. HEREFTER LURITE MINIMUM TWIE YER. DO NOT LURITE THE LUMINIUM RILS. SEE LSO INSTRUTIONS ON PGE 28-2.