Technical Newsletter. Contents. By: Technogym After Sales Service N. 94 October/Novembre 2007

Transcription

1 Technical Newsletter By: Technogym After Sales Service N. 94 October/Novembre 2007 Contents Bike Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display Recline Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display Run Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video Breakage of tread belt motor support New running deck Frontek LCD inverter New SW version for 700 and 900 WTV UB New SW version for 700 and 900 WTV UB ACTIVE WTV Synchro Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video 500iSP-700iSP: noise coming from primary shaft Tool for disassembling primary shaft New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display Step Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display Wave Excite IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video Creaking of belts New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Jog Excite New emergency button New SW version for 500 and 700 Selection Line New colour of cams New adjustable bushing for Lat Machine, Upper Back, Low Row, Crunch Bench and Lower Back Bench P915 Crunch Bench: new backrest adjuster pin Loosening of counterweight assembly on Abdominal crunch and Lower Back Dropping of lever caps on Arm Curl & Arm Extension Abdominal Crunch, Total Abdominal and Rotary Torso: upgrading of backrest lever and its spring Element Line Leg Press: excessive play of seat carriage on the position adjustment bar. XTPRO Line New SW version Kinesis Personal Complete arm assembly New display assembly Isocontrol Use of configuration key on Isocontrol with new dual reader TGS reader Compatibility of new keys and Botom-Mifare dual TGS readers Service Product Touch-up paint for PURESTRENGTH Service Box Codes USB-serial Converter Codes for accessing the machine monitoring and configuration functions Technogym After Sales Service: - fax:

2 Bike Excite Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

3 Bike Excite CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine R AA preconnection upgrade kit. A AA-E A AA-U WTV upgrade A AA-E A AA-U WTV upgrade * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

4 Bike Excite ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. NEW MODEL - 0WQ00371AB New SW version for 700 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. page 3

5 Bike Excite WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 4

6 Bike Excite Codes for WTV display Following the evolution of the W TV display to a version now incompatible with the previous components, the display housing assemblies H AE-GV and R AA are no longer available as replacement parts. They will be replaced by order code R AA for the complete assembly, comprising the plastic housing, touch screen, LCD and plate support. The table below details the correct order codes for the display replacement parts, as a function of the machine configurations: BIKE EXCITE: display Wellness TV 12 HW CONFIGURATION REFERENCE SPARE PARTS CODE LCD used LCD protection Spare LCD Spare LCD inverter Connector board Spare CPU board Spare Touch Screen AUX input board WTV (dot matrix) Samsung R AA 0WQ00268AA 0WQ WQ00271AA-# 0WT00032AA 0WQ00111AB WTV Touch Screen Samsung R AA 0WQ WQ00271AA-# 0WQ00115AC WTV Touch Screen NCB Samsung Sharp R AA R AA R AA 0WQ00259AB 0WQ00259AB 0WQ00259AB 0WQ00271AA-# 0WQ00271AA-# 0WQ00271AA-# 0WQ00115AC 0WQ00115AC 0WQ00115AC WTV Unified Board Sharp R AA 0WQ00342AA-# 0WQ00328AA WTV NEW Unified Board Sharp 0WR00646AA 0WQ00342AB-# 0WQ00328AA Spare casing H AB R AA R AA R AA W AB W AB W AB / / page 5

7 Recline Excite Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

8 Recline Excite CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine R AA preconnection upgrade kit. A AA-E A AA-U WTV upgrade A AA-E A AA-U WTV upgrade * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

9 Recline Excite ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. NEW MODEL - 0WQ00371AB New SW version for 700 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. page 3

10 Recline Excite WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 4

11 Recline Excite Codes for WTV display Following the evolution of the W TV display to a version now incompatible with the previous components, the display housing assemblies H AE-GV and R AA are no longer available as replacement parts. They will be replaced by order code R AA for the complete assembly, comprising the plastic housing, touch screen, LCD and plate support. The table below details the correct order codes for the display replacement parts, as a function of the machine configurations: RECLINE EXCITE: display Wellness TV 12 HW CONFIGURATION REFERENCE SPARE PARTS CODE LCD used LCD protection Spare LCD Spare LCD inverter Connector board Spare CPU board Spare Touch Screen AUX input board WTV (dot matrix) Samsung R AA 0WQ00268AA 0WQ WQ00271AA-# 0WT00032AA 0WQ00111AB WTV Touch Screen Samsung R AA 0WQ WQ00271AA-# 0WQ00115AC WTV Touch Screen NCB Samsung Sharp R AA R AA R AA 0WQ00259AB 0WQ00259AB 0WQ00259AB 0WQ00271AA-# 0WQ00271AA-# 0WQ00271AA-# 0WQ00115AC 0WQ00115AC 0WQ00115AC WTV Unified Board Sharp R AA 0WQ00342AA-# 0WQ00328AA WTV NEW Unified Board Sharp 0WR00646AA 0WQ00342AB-# 0WQ00328AA Spare casing H AB R AA R AA R AA W AB W AB W AB / / page 5

12 Run Excite 2007/08 Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video Breakage of tread belt motor support New running deck Frontek LCD inverter New SW version for 700 and 900 WTV UB New SW version for 700 and 900 WTV UB ACTIVE WTV IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

13 Run Excite 2007/08 CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine A upgrade kit 15 A upgrade kit 15 A upgrade kit 15 R AA preconnection upgrade kit. A upgrade kit 15 A AA-E A AA-U Kit upgrade WTV Run 700 or A AA-E A AA-U Kit upgrade WTV Run 900 A Kit upgrade 15 * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

14 Run Excite 2007/08 ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. NEW MODEL - 0WQ00371AB Breakage of tread belt motor support In some cases, breakage of the motor support has been caused by the absence of the washers and spacers which should be fitted on the fixing screws. It is important, whenever the motor is removed and then reassembled on the machine, to check that all the washers are correctly repositioned as shown in the drawing below. page 3

15 Run Excite 2007/08 The order codes for the components indicated in the figure are given in the table below. Ref. CODE DESCRIPTION Qty. 1 R AA Motor support assembly 1 2 0B000610AA Spacer 4 3 0Z323 Washer 4 4 0Z306 Washer 4 5 0B000736AA Spacer 4 6 0Z044 Bolt M10x ZV00176AA Bolt M10x35 4 The code R AA (ref. 1) includes the motor support plus all the necessary washers. New running deck With a view to continuous product improvement, the machines are now being equipped with a new running deck which differs from the preceding model in that the surface laminate of the deck is 8 cm narrower. The deck used until now did not cause any particular problems, so there is no need to replace it other than as part of routine maintenance. Because the two decks are fully interchangeable, the order code R AB remains unchanged. Frontek LCD inverter As reported in TN 09/2006, beginning about a year ago, Frontek LCD inverters are being used in place of the previous TDK model. Because these two components are not interchangeable, when replacing an inverter it is important to carefully check the machine configuration to determine whether it uses the old TDK or the new Frontek inverter, so as to order the correct replacement part. The two inverter models are shown in the table below: page 4

16 Run Excite 2007/08 TDK Inverter FRONTEK inverter 1. To replace a TDK inverter with the Frontek inverter, an order code has been created which includes all the components needed to assemble the new model in place of the old one. The order code of this kit is W AA. 2. To replace a Frontek inverter with another of the same type, it is possible to order the inverter by itself. The code for ordering only the inverter is 0WR00596AA. New SW version for 700 and 900 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 and 900 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal page 5

17 Run Excite 2007/08 persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 6

18 Synchro Excite Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video 500iSP-700iSP: noise coming from primary shaft Tool for disassembling primary shaft New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

19 Synchro Excite CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine R AA preconnection upgrade kit. A AA-E A AA-U WTV upgrade A AA-E A AA-U WTV upgrade * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

20 Synchro Excite ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. NEW MODEL - 0WQ00371AB 500iSP-700iSP: noise coming from primary shaft In cases where there is noise on the machine coming from the primary shaft, check the condition of the spacer indicated in the figure below. In fact this component is subjected to stresses which may cause it to break, resulting in noisy operation of the machine. page 3

21 Synchro Excite To prevent recurrence of these breakages, the old spacer has now been replaced by an opportunely modified new model with code 0B000750AB. Tool for disassembling primary shaft A special tool for disassembling the primary shaft of the Synchro machine is now available with order code R AB. The particular configuration of the primary shaft assembly, which includes 2 Belleville washers for eliminating the play between components, makes it necessary to use the above tool for its assembly and disassembly. The above tool is supplied complete with an instruction sheet. New SW version for 700 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. page 4

22 Synchro Excite Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 5

23 Synchro Excite Codes for WTV display Following the evolution of the W TV display to a version now incompatible with the previous components, the display housing assemblies H AE-GV and R AA are no longer available as replacement parts. They will be replaced by order code R AA for the complete assembly, comprising the plastic housing, touch screen, LCD and plate support. The table below details the correct order codes for the display replacement parts, as a function of the machine configurations: SYNCHRO EXCITE: display Wellness TV 12 HW CONFIGURATION REFERENCE SPARE PARTS CODE LCD used LCD protection Spare LCD Spare LCD inverter Connector board Spare CPU board Spare Touch Screen Spare casing WTV Touch Screen Samsung R AA 0WQ WQ00271AA-# R AA WTV Touch Screen NCB Samsung Sharp R AA R AA R AA 0WQ00258AB 0WQ00258AB 0WQ00258AB 0WQ00271AA-# 0WQ00271AA-# 0WQ00271AA-# R AA R AA W AB WTV Unified Board Sharp R AA 0WQ00342AA-# W AB WTV NEW Unified Board Sharp 0WR00646AA 0WQ00342AB-# W AB AUX input board 0WQ00115AC 0WQ00115AC 0WQ00115AC 0WQ00115AC 0WQ00328AA 0WQ00328AA / / page 6

24 Step Excite Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV Codes for WTV display IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

25 Step Excite CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine R AA preconnection upgrade kit. A AA-E A AA-U WTV upgrade A AA-E A AA-U WTV upgrade * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

26 Step Excite ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. NEW MODEL - 0WQ00371AB New SW version for 700 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. page 3

27 Step Excite WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 4

28 Step Excite Codes for WTV display Following the evolution of the W TV display to a version now incompatible with the previous components, the display housing assemblies H AE-GV and R AA are no longer available as replacement parts. They will be replaced by order code R AA for the complete assembly, comprising the plastic housing, touch screen, LCD and plate support. The table below details the correct order codes for the display replacement parts, as a function of the machine configurations: STEP EXCITE: display Wellness TV 12 HW CONFIGURATION REFERENCE SPARE PARTS CODE LCD used LCD protection Spare LCD Spare LCD inverter Connector board Spare CPU board Spare Touch Screen Spare casing WTV Touch Screen NCB Samsung Sharp R AA R AA R AA 0WQ00258AB 0WQ00258AB 0WQ00258AB 0WQ00271AA-# 0WQ00271AA-# 0WQ00271AA-# R AA R AA W AB WTV Unified Board Sharp R AA 0WQ00342AA-# W AB WTV NEW Unified Board Sharp 0WR00646AA 0WQ00342AB-# W AB AUX input board 0WQ00115AC 0WQ00115AC 0WQ00115AC 0WQ00328AA 0WQ00328AA / / page 5

29 Wave Excite 2007/07 Contents IPod docking station compatibility on WTV models ipod not detected by the machine Problem displaying ipod video Creaking of belts New SW version for 700 WTV UB New SW version for 700 WTV UB ACTIVE WTV IPod docking station compatibility on WTV models Starting from September 2007, there is a new " station" device available for connecting and managing ipod players on ACTIVE Wellness TV models. This device takes the form of a slot on the upper part of the display, into which an ipod can be inserted and subsequently controlled via the machine's touch screen. The slot is provided with a cover for when no ipod device is being used. NEW MACHINES It is possible to order an ACTIVE WTV version machine with the docking device pre-installed. These machines will be distinguished by a different value for the 7 th character of the machine code, which is already used to indicate the presence or absence of the TGS reader, and will therefore now have 4 possible values: N no device pre-installed on the machine. T machine with TGS reader. I machine with station. A machine with station TGS reader. For example, on a Run Excite the code might be: D447EII Run 700 with Active Wellness TV and pre-installed station. MACHINES ALREADY ON THE MARKET To install a docking station on a WTV machine already on the market, refer to the table below: page 1

30 Wave Excite 2007/07 CODE MACHINE D4xxxII MODEL ACTIVE WTV SW with station is already installed. HW UPGRADE SW UPGRADE ACTIVE WTV D4xxxIA None ACTIVE WTV SW with station is already installed. D4xxxIT D4xxxIN D4xxxEx D4xxxLx None ACTIVE WTV SW is already installed. HW: install the upgrade kit. SW: not required ACTIVE WTV SW is already installed. HW: install the upgrade kit SW: not required Configuration 1 This is the WTV Touch Screen model with unified UB circuit board and display housing preconnected for installation of the * HW: install the upgrade kit. Configuration 2 This is the WTV Touch Screen model with unified UB circuit board and display housing T preconnected for installation of the * HW: install the pre-connection upgrade kit and the upgrade kit. Configuration 3 This is the WTV touch screen model with CPU board and NCB or connector board. HW: install a new model of WTV display with unified board on the machine This is the model with LED display. HW: install a WTV display on the machine R AA preconnection upgrade kit. A AA-E A AA-U WTV upgrade A AA-E A AA-U WTV upgrade * The pre-connected machines are those which have the opening for the docking station in the display frame and a connecting cable (remove the cover from the opening and check whether the cable is present). page 2

31 Wave Excite 2007/07 ipod not detected by the machine When the machine fails to detect an ipod device inserted into its docking station, the problem may be due to an incorrect connection of cable 0WCU0167AB, leading from the external connectors board to the docking station board. In particular, because the cable in question has identical connectors on either end, it can sometimes be connected the wrong way round, causing the device to fail to function. Currently, to avoid inverting the cable, a marker is used to identify the end that plugs into the connector board. Problem displaying ipod video Occasionally, on machines equipped with station, it can happen that music or video cannot be played back. More specifically, although the machine does detect the ipod, the various menus remain completely empty. This problem is caused by a defect in the electronics board of the docking station, and can be corrected only by replacing this board. The new circuit board has order code 0WQ00371AB and replaces the preceding version 0WQ00371AA. The two versions can be distinguished by looking at the version number on the sticker: V: 3.0 for the old model (0WQ00371AA) and V: 4.0 for the new one (0WQ00371AB), as shown in the figure below. OLD MODEL - 0WQ00371AA The two components are mechanically interchangeable. Creaking of belts NEW MODEL - 0WQ00371AB To prevent the creaking sound produced by friction of the belts against the motion drive system components, it is recommended to lubricate the belts with oil (order code 0V910), applying it directly on the points where the noise is produced. New SW version for 700 WTV UB It is version number available in the 10 standard languages. The main modifications in this version are: Corrected the problem which allowed the training keys to be enabled using an empty TGS key, even when these had been disabled from the configuration menu. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal page 3

32 Wave Excite 2007/07 persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: in order to implement the above described functions. New SW version for 700 WTV UB ACTIVE WTV It is version number available in 11 different languages. The main modifications in this version are: Added a pop-up signaling the end of the training session on reaching the maximum duration programmed from the machine configuration menu. Defined a function for deleting previously tuned channels from the TV and Radio menus. Fixed the problem which prevented a TGS key training session from being ended on reaching the maximum duration programmed on the machine. Modified handling of Touch Screen malfunction: on powering up the machine, if there is any extraneous material between the frame and touch screen that produces a continuous pressure, first of all the calibration procedure is launched, then if the continuous signal persists the message Remove fingers from screen, then press the 3 crosses that appear in sequence to calibrate is displayed, after which the calibration procedure is aborted, returning the machine to stand-by mode. If the pressure on the touch screen continues when the machine is in stand-by mode, the message Screen out of order. Check that it's clean between screen and frame and restart equipment is displayed. Corrected the error which disabled the ipod control button, when the machine returned to stand-by mode at the end of a training session. The "ipod" button is now disabled only when the device is disconnected. Corrected the error which prevented correct display of video from the ipod if the machine was configured with a different television standard from that of the ipod. Now the television standard of the machine is automatically set to match that of the ipod when the device is connected, and reverts to the default setting as soon as the ipod is removed. Corrected the error which caused the TV switch off and on again in touch-screen mode, whenever a TGS key or ipod was inserted while touching the touch screen at the same time. Corrected the error which caused the machine to reset if the Zoom and Zoom - keys were pressed in rapid succession during the training session. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: if any of the above problems are observed, in order to implement the new functions. page 4

33 JOG Excite 2007/01 Contents New emergency button New SW version for 500 and 700 New emergency button To facilitate coupling of the plastic cover with the underlying support of the emergency button, shown in the figure below, the two components have been slightly modified, so that they are no longer interchangeable with the corresponding old models. To avoid the risk of ending up with two components that cannot be assembled together, the 2 parts will from now on be supplied jointly with code R AA, rather than separately as before. New SW version for 500 and 700 It is version number available in 10 different languages. The main change in this version is the possibility of configuring the duration of the cool-down period, by entering the number of seconds into the "COOLDOWN TIME" parameter in the user menu. This parameter can be configured in the range of 5 to 180 seconds. page 1

34 Selection Line Contents New colour of cams New adjustable bushing for Lat Machine, Upper Back, Low Row, Crunch Bench and Lower Back Bench P915 Crunch Bench: new backrest adjuster pin Loosening of counterweight assembly on Abdominal crunch and Lower Back Dropping of lever caps on Arm Curl & Arm Extension Abdominal Crunch, Total Abdominal and Rotary Torso: upgrading of backrest lever and its spring New colour of cams S e l e c t i o n L i n e The process for coloring the cams used on the entire Personal Selection line has been changed. The new grey colour, in addition to being slightly lighter than the previous shade, also has a slightly textured surface finish. The cams with the new finish are fully interchangeable with the preceding versions. TE: whenever a cam is replaced on a machine, it is recommended to also replace the other ones to ensure uniformity of appearance. New adjustable bushing for Lat Machine, Upper Back, Low Row, Crunch Bench and Lower Back Bench The adjustable bushing used on the above machines, and shown in the figure below, has been modified. In particular, the two holes for fixing the bushing to the frame, which are not used on the Personal Selection line machines, have been eliminated. The code of the new adjustable bushing is W AA-GD or W AA-GG, depending on the machine configuration; it is completely interchangeable with the old model. P915 Crunch Bench: new backrest adjuster pin Because of the stresses to which the pin in question (shown in the figure below) is subjected, it is now put through a special treatment to increase its strength. The new pin, which has order code 0P000289AA, is completely interchangeable with the old one. The first production machine to incorporate this new solution has SN P page 1

35 Selection Line Loosening of counterweight assembly on Abdominal crunch and Lower Back The method of fixing the counterweight hub on the lever has been modified, because the preceding solution allowed the components to work loose over time. The new solution involves use of a clamp type hub which is fixed to the lever as shown in the figure below, and a new self-locking ring. S e l e c t i o n L i n e The new solution is interchangeable with the old one and the codes identifying the new components are given in the table below: Ref. MACHINE CODE DESCRIPTION 1 Abdominal Crunch 0N000173AB-# Counterweight hub Lower Back 0N000173AB-# Counterweight hub 2 All 0Z117 Screw M8x16 3 All 0Z452 Self-locking ring M25x1. 5 Where the # character must be replaced with the desired color code. Dropping of lever caps on Arm Curl & Arm Extension The end caps used on the Arm Curl and Arm Extension machine levers have been modified to prevent them from dropping off during the exercise. The new caps, which are completely interchangeable with the preceding model, have order code W AB-GD or W AB-GG, depending on the machine configuration. page 2

36 Selection Line Abdominal Crunch, Total Abdominal and Rotary Torso: upgrading of backrest lever and its spring A number of upgrade kits have been created for replacing the gas piston spring, originally installed on the above listed machines to support the backrest lever, with the new torsion spring solution. The kits contain all the components needed for upgrading the different machine configurations to the current solution for both spring and lever (which is dependent on the type of spring used). S e l e c t i o n L i n e To summarize and further clarify the correct use of the various codes given in previous issues of the Technical Newsletter, the following table details the purpose of each kit. CODE R AA-# (Abdominal Crunch) R AA-# (Total Abdominal) R AA-# (Rotary Torso) (TN Selection 2007/04) R AC-# (Abd. Crunch/Total Abd.) R AB-# (Rotary Torso) (TN 2006/09 Selection 2006/07) R AA (Abd. Crunch/Total Abd. /Rotary torso) (TN 2006/06 Selection 2006/04) WHAT IS IT FOR? When the backrest lever needs to be replaced on a machine that still has the "gas piston" solution, this code includes all the components for replacing the lever and upgrading the machine to the torsion spring solution, including the kit for keeping it in the raised position when not in use. (the gas piston solution is no longer available, and therefore the machine must be upgraded to the current "torsion spring" solution) When the gas piston needs to be replaced on a machine that still uses that solution, this code includes all the components for installing the "torsion spring" solution, complete with the kit for keeping it in the raised position when not in use. (the gas piston solution is no longer available and the machine must be upgraded to the current "torsion spring" solution) If the backrest lever on a machine with torsion spring solution does not stay up when not in use, this code includes all the components for tightening the spring so that it keeps the lever raised. page 3

37 Selection Line OTHER CODES FOR MACHINES WITH GAS PISTON This code includes: R AA-# (Abd. Crunch/Total Abd.) (TN 2006/09 Selection 2006/07) Backrest accessory (A V) Kit for upgrading to solution with torsion spring (R AC-#) S e l e c t i o n L i n e R AA-# (Rotary Torso) (TN 2006/09 Selection 2006/07) This code includes: OTHER CODES FOR MACHINES WITH TORSION SPRING R AA-# (Abd. Crunch/Total Abd. /Rotary torso) (TN 2006/09 Selection 2006/07) Backrest accessory (A V) Kit for upgrading to solution with torsion spring (R AB-#) This code includes: Backrest accessory (A V) Kit for tightening the torsion spring (R AA-#) A V page 4

38 Element Line 2007/07 Contents Leg Press: excessive play of seat carriage on the position adjustment bar. Leg Press: excessive play of seat carriage on the position adjustment bar. To eliminate excessive play of the seat carriage on the position adjustment bar, the rollers indicated in the figure below, which allow the carriage to slide along the bar, have been modified. In addition to being differently shaped, with an augmented diameter of the central section, the new rollers also adopt a different fixing method, and in particular the lower ones have a cam for adjusting their position and minimising the amount of play between the bar and the 4 rollers. E l e m e n t L i n e The figure illustrates the assembly of the new solution, showing the components both inside and outside the carriage frame. The order codes for the components indicated in the figure are given in the table below. Ref. CODE DESCRIPTION Qty. 1 0U000263AC Roller 4 0P001130AA Pin 4 2 0B00110AA Spacer 8 3 0G283 Nut cap 8 4 0Z044 Screw m10x Z3003 Washer 8 6 0B Spacer ring 8 7 0P6015 Cam 4 In addition to the details in the table, the machines currently in production also have a modified carriage frame for accommodating the new rollers. For already installed machines that have a problem with excessive play, it is possible to use order code R AA which includes all the components illustrated above with their assembly instructions, without need to replace the carriage frame. page 1

39 XTPRO Line 2007/02 Contents New SW version New SW version This SW version implements the modifications necessary for supporting the new Mifare TGS keys and the new dual reader. WHEN TO UPGRADE ALREADY INSTALLED MACHINES: whenever one of the new dual Botom/Mifare readers is used. The codes of the EPROMs with the new SW for the various machines are given in the table below: X T P R O L i n e MACHINE SW rev. EPROM CODE POSSIBLE LANGUAGE VARIANTS BIKE XTPRO WE00366AB-# BR/DE/ES/FR/IT/JP/NL/UK/US RECLINE XTPRO WE00367AB-# BR/DE/ES/FR/IT/JP/NL/UK/US ROTEX XTPRO WE00369AB-# BR/DE/ES/FR/IT/JP/NL/UK/US GLIDEX XTPRO WE00370AB-# BR/DE/ES/FR/IT/JP/NL/UK/US STEP XTPRO WE00371AB-# BR/DE/ES/FR/IT/JP/NL/UK/US TOP XTPRO WE00368AB-# BR/DE/ES/FR/IT/JP/NL/UK/US RUN XTPRO WE00230AC-# BR/DE/ES/FR/IT/JP/NL/UK/US The binaries can be downloaded from the TG Direct website. page 1

40 Contents Kinesis Personal 2007/04 Complete arm assembly New display assembly Complete arm assembly The code R AA is now available for ordering the preassembled components shown in the figure below, which can be used on all 4 arms of the machine. New display assembly K i n e s i s To prevent the formation of air bubbles between the protective films of the display, the display assembly has been modified to replace the two protective films with a single, thicker one. The new assembly is interchangeable with the old version and has code W AC. page 1