Sprecher + Schuh offers a broad selection

Transcription

1 Preassembled or build from stock Easy, fast, economical enclosed starters for applications up to 30HP Most are equipped with Thermal Overload protection as standard Sprecher + Schuh offers a broad selection of pre-assembled or build-fromstock starters housed in a high impact, non-metallic, cul Approved, Type 1, 12, 4, 4X enclosure. Built for convenience, space savings and economy, are efficiently designed to use stock A7 contactors and EP7 or T7N overloads usually stocked by distributors. ontactor and overload are either pre-wired and pre-mounted onto the enclosure s built-in DIN-rail or may be ordered as separate components. Ample knockouts and open terminals guarantee quick, no fuss wiring. Sized for most industrial applications control motors up to 460V in two sizes of enclosures, measuring only 208 x 98mm (7.4 x 3.9 ) or 250 x 125mm (9.85 x 4.93 ) for our larger sizes. This covers over 85% of industrial motor control applications in a very compact package that can be mounted adjacent to or directly on equipment. Thermal overload protection, sized 9 to 23 amps, are equipped with Sprecher + Schuh s T7N bimetallic thermal overload relay as standard. The consistent high quality of our thermal overload relays is ensured by a complex current calibration procedure performed after each unit is at full operating temperature. are also available with our advanced EP7 Solid State Overload Relay (select appropriate overload relay code for this option) Solid state overload options, sizes 9 to 23 amps, can also be supplied with Sprecher + Schuh s EP7 solid state overload relay. The EP7 Overload is standard on larger (sizes 30 to 43 amps) and all reversing. The EP7 solid state overload relays measure motor current directly through integrated current transformers and on board electronics. The electronics provide increased accuracy and numerous other advantages over electromechanical relays. Learn more about Sprecher + Schuh overload relays in Section B of this catalog. Build it yourself may be assembled from stock components. Just grab a A7 contactor and overload of your choice and snap them into the enclosure. Minimal wiring is required and assembly can be completed in minutes. Start-Stop or Reset only Hand-Off-Auto with Pilot Light Emergency Stop Multi-Function Forward-Stop-Reverse options ombination Kwikstarters 14

2 X7 Type E/F ombination Motor ontrollers KTA7 can be applied in combination with a A7 contactor for remote control and an enclosure with matching environmentally approved thru-thedoor handle disconnect mechanism to meet all requirements for a onstruction Type E or F ombination Starter. This selection of individual ombination starters are smaller and are less expensive than lassic onstruction Type A (Fusible), or Type (Thermal-magnetic Molded ase ircuit Breaker), as offered in the following pages. Sprecher + Schuh has developed a KWIKStarter version of the ombination Motor ontroller which can be easily field assembled or can be purchased as a factory assembly. For details and catalog number selection on these economical combination starter alternatives turn to page F98. Why Type E/F? NE defines that the short-circuit protection of a single motor branch circuit shall be provided by a set of fuses or a thermalmagnetic molded case circuit breaker. Alternatively NE also permits the use of a Self-protected ombination Motor ontroller can be used to not only provide short-circuit protection for a single motor branch circuit but also provide a means of disconnect and overload protection. Self-protected ombination motor controllers like KTA7 can be combined with A7, providing a coil for cover control or remote operation. This results in a onstruction Type E or Type F (based on selection depending on published UL ratings) ombination starter per UL508. For details of UL, NE and SA application standards and rules please see our online white paper, Applying KT7 Motor ontrollers. See page F98 for Type E/F X7 15

3 Series AK7 & BK7 - A oils with T7N or EP7 Overload Relays; ➊➏ over ontrol/ (KS7-0S1/0S4) Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ KWIKstarter with Start & Raised Stop ❹➎ 1/2 1 1/2 ~ ~ ~ ~ BK P2 ~ ~ /2 AK P2 292 Q1 1/2 2 ~ ~ ~ ~ BK P2 ~ ~ /2 10 AK P2 327 Q1 1 3 ~ ~ ~ ~ BK P2 ~ ~ AK P2 351 Q1 2 3 ~ ~ ~ ~ BK P2 ~ ~ 5 7 1/ AK P2 378 Q1 KWIKstarter with Reset 1/2 1 1/2 ~ ~ ~ ~ BK P0 267 Q1 ~ ~ /2 AK P0 1/2 2 ~ ~ ~ ~ BK P0 ~ ~ /2 10 AK P0 1 3 ~ ~ ~ ~ BK P0 ~ ~ AK P0 2 3 ~ ~ ~ ~ BK P0 ~ ~ 5 7 1/ AK P0 303 Q1 327 Q1 353 Q1 oil odes ➎ A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon V 277V ommon ~ V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon ontrol ircuit Note ommon: oils are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils are assumed to be from a separate source and will not be connected to the line source per the table. This item is available in the ORANGE E PRESS 3-day shipping program Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ are designed for three-wire control circuits. Two-wire (maintain) control can be accomplished by adding pushbutton latch KS7-PLA. ➋ A special design NO auxiliary contact (at.# KS7-PK) is used as the holding circuit interlock, as well as, the START button interface. It is not available for other use. ➌ Refer to page 33 for dimensional information. ➍ STOP button also functions as RESET button. Plastic Bezel is standard. ➎ Other voltages available, see Section A. ➏ Use T7N or EP7-ED/EP7-EE overload. 16

4 Series AK7 & BK7 - Electronic D oils with T7N or EP7 Overload Relays; ➊➍➎➏ over ontrol/ (KS7-0S1/0S4) Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ KWIKstarter with Start & Raised Stop ❹➎ 1/2 1 1/2 ~ ~ ~ ~ BK7-9E- - -P2 367 Q1 ~ ~ /2 AK7-9E- - -P2 1/2 2 ~ ~ ~ ~ BK7-12E- - -P2 412 Q1 ~ ~ /2 10 AK7-12E- - -P2 1 3 ~ ~ ~ ~ BK7-16E- - -P2 442 Q1 ~ ~ AK7-16E- - -P2 2 3 ~ ~ ~ ~ BK7-23E- - -P2 ~ ~ 5 7 1/ AK7-23E- - -P2 473 Q1 KWIKstarter with Reset 1/2 1 1/2 ~ ~ ~ ~ BK7-9E- - -P0 ~ ~ /2 AK7-9E- - -P0 1/2 2 ~ ~ ~ ~ BK7-12E- - -P0 ~ ~ /2 10 AK7-12E- - -P0 1 3 ~ ~ ~ ~ BK7-16E- - -P0 ~ ~ AK7-16E- - -P0 2 3 ~ ~ ~ ~ BK7-23E- - -P0 ~ ~ 5 7 1/ AK7-23E- - -P0 342 Q1 387 Q1 417 Q1 449 Q1 oil odes ➎ D oil odes 12E 24E Voltage 12V 24V Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ are designed for three-wire control circuits. Two-wire (maintain) control can be accomplished by adding pushbutton latch KS7-PLA. ➋ A special design NO auxiliary contact (at.# KS7-PK) is used as the holding circuit interlock, as well as, the START button interface. It is not available for other use. ➌ Refer to page 33 for dimensional information. ➍ STOP button also functions as RESET button. Plastic Bezel is standard. ➎ A7-9E 23E with electronic coils are not interchangeable with non-electronic D or A coils ➏ Use T7N or EP7-ED/EP7-EE overload. 17

5 Series AK7 & BK7 - A oils with EP7 Overload Relays ➊ (KS7-2S4) Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ with A oil 2 5 ~ ~ ~ ~ BK ETD-P ~ ~ 7-1/ AK P 3 5 ~ ~ ~ ~ BK ETD-P ~ ~ AK P 3 7-1/2 ~ ~ ~ ~ BK ETD-P ~ ~ AK P Replace with one of the following Overload Relays For use with KWIKstarter... Amp Overload Relay ode ( ) atalog No. (of Overload Relay used) 3-Phase / Manual Reset / lass D1D EP7-ED1D D1DD EP7-ED1DD +0 AK D1ED EP7-ED1ED D1FD EP7-ED1FD +0 3-Phase / Auto or Manual Reset / lass 10, 15, 20, ED EP7-EED EDD EP7-EEDD +21 AK EED EP7-EEED EFD EP7-EEFD +21 Pilot Device Options (includes reset) ➋➎ Replace in catalog number with Pushbutton Description START-STOP Multi-function (shown) 3U Standard I-O Multi-function 4U Standard OFF-ON 2-Position Selector switch 6 Standard Pilot Light Red (LED) with START-STOP Multi-function 1R3U +50 Pilot Light Red (LED) with I-0 Multi-function 1R4U +50 Optional A7 Modifications (Factory Assembled) Description Add to end of catalog number Electronic Interface -JE +94 Surge Suppressor RD Surge Suppressor Varistor -V +54 Additional N ontact -L Additional NO ontact -L oil odes (Q) ➍➏ 447 Q2 491 Q2 581 Q2 A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon V 277V ommon ~ V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Pilot lights are 240 VA maximum. See this page only ➊ Use EP7-ED/EP7-EE overloads only. Single-phase applications utilize EP7S-EETD only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 31 for wiring diagram and 34 for dimensional information. ➍ Other voltages available, see Section A. ➎ One and only one Pilot Device option must be selected. If Pilot Light option is selected then coil voltage must be 24V, 120V or 240V A only. ➏ PT not possible with KS7-2S4 (Q2) enclosure. 18

6 Series AK7 & BK7 - Electronic D oils with EP7 Overload Relays ➊ (KS7-2S4) Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ with Electronic D oil ➍ 2 5 ~ ~ ~ ~ BK7-30E- -ETD-P 554 Q2 ~ ~ 7-1/ AK7-30E- - -P 3 5 ~ ~ ~ ~ BK7-37E- -ETD-P 613 Q2 ~ ~ AK7-37E- - -P 3 7-1/2 ~ ~ ~ ~ BK7-43E- -ETD-P ~ ~ AK7-43E- - -P 743 Q2 Replace with one of the following Overload Relays For use with KWIKstarter... Amp Overload Relay ode ( ) atalog No. (of Overload Relay used) 3-Phase / Manual Reset / lass D1D EP7-ED1D D1DD EP7-ED1DD +0 AK D1ED EP7-ED1ED D1FD EP7-ED1FD +0 3-Phase / Auto or Manual Reset / lass 10, 15, 20, ED EP7-EED EDD EP7-EEDD +21 AK EED EP7-EEED EFD EP7-EEFD +21 Pilot Device Options (includes reset) ➋➎ Replace in catalog number with Pushbutton Description START-STOP Multi-function (shown) 3U Standard I-O Multi-function 4U Standard OFF-ON 2-Position Selector switch 6 Standard Pilot Light Red (LED) with START-STOP Multifunction 1R3U +50 Pilot Light Red (LED) with I-0 Multi-function 1R4U +50 Optional A7 Modifications (Factory Assembled) Description Add to end of catalog number Electronic Interface -JE +94 Surge Suppressor RD Surge Suppressor Varistor -V +54 Additional N ontact -L Additional NO ontact -L oil odes ➍➏ D.. oil ode Voltage VD 12E 12V 24E 24V 36E 36-48V 48E 48-72V 110E V 220E V Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option See this page only ➊ Use EP7-ED/EP7-EE overloads only. Single-phase applications utilize EP7S-EETD only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 31 for wiring diagram and 34 for dimensional information. ➍ A7-9E 55E with electronic coils are not interchangeable with non-electronic D or A coils. ➎ One and only one Pilot Device option must be selected. ➏ PT not possible with KS7-2S4 (Q2) enclosure. 19

7 Series AK7 & BK7 - A or D with H-O-A with T7N or EP7 Overload Relays with H-O-A and Light ➊➋➌➎➏ over ontrol/ Single Ø Total Aux. ontacts Installed 115V 230V 200V 230V 460V 575V NO N atalog Number ➍ KWIKstarter with Reset and H-O-A Selector Switch and Light with A oil 1/2 1 1/2 ~ ~ ~ ~ BK P0+1R7 ~ ~ /2 AK P0+1R7 1/2 2 ~ ~ ~ ~ BK P0+1R7 ~ ~ /2 10 AK P0+1R7 1 3 ~ ~ ~ ~ BK P0+1R7 ~ ~ AK P0+1R7 ode 654 Q1 721 Q1 765 Q1 2 3 ~ ~ ~ ~ BK P0+1R7 808 Q1 ~ ~ 5 7 1/ AK P0+1R7 KWIKstarter with Reset and H-O-A Selector Switch and Light with Electronic D oil ➐ 1/2 1 1/2 ~ ~ ~ ~ BK7-9E- - -P0+1R7 ~ ~ /2 AK7-9E- - -P0+1R7 1/2 2 ~ ~ ~ ~ BK7-12E- - -P0+1R7 ~ ~ /2 10 AK7-12E- - -P0+1R7 1 3 ~ ~ ~ ~ BK7-16E- - -P0+1R7 ~ ~ AK7-16E- - -P0+1R7 2 3 ~ ~ ~ ~ BK7-23E- - -P0+1R7 ~ ~ 5 7 1/ AK7-23E- - -P0+1R7 803 Q1 890 Q1 945 Q Q1 oil odes ➐ A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon D.. oil ode Voltage VD 12E 12V 24E 24V ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Line Voltage not listed: (i.e.: 480 and 575 VA) require a separate control source (i.e.: 120 VA). D7D pilot devices are rated 300 VA maximum. This item is available in the ORANGE E PRESS 3-day shipping program Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ This is a factory assembly. The KS7-0S1 (Q1) enclosure does not include knock-outs for field assembly of this starter. ➋ Uses D7D-P4N_ Red Monolithic Run pilot light with LED bulb. Pilot light voltage to match coil voltage for 24, 120, 240 VA control. Red Run Light can be changed for Green. hange +1R7 to +1G7. For example, AK P0+1R7 becomes AK P0+1G7. ➌ Uses D7D-SM32x20 Monolothic 3-position selector switch for maintain control, HAND-OFF- AUTO function with legend plate. ➍ Refer to page 32 for wiring and dimensional information. This is a clam-shell enclosure design with wires to cover controls. ➎ Uses T7N or EP7-ED/EP7-EE overload. ➏ One NO auxilliary for customer use. There is no room for additional auxilliaries. ➐ A7-9E 23E with electronic coils are not interchangeable with non-electronic D or A coils. 20

8 Series AK7 & BK7 - A with E-Stop with T7N or EP7 Overload Relays with I-O Multifunction and E-Stop ➊➋➌➎➏ over ontrol/ Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➍ KWIKstarter with Reset, Multifunction I-O Pushbutton and E-Stop with A oil 1/2 1 1/2 ~ ~ ~ ~ BK P0+4U-9 ~ ~ /2 AK P0+4U-9 1/2 2 ~ ~ ~ ~ BK P0+4U-9 ~ ~ /2 10 AK P0+4U ~ ~ ~ ~ BK P0+4U-9 ~ ~ AK P0+4U Q1 438 Q1 462 Q1 2 3 ~ ~ ~ ~ BK P0+4U-9 ~ ~ 5 7 1/ AK P0+4U Q1 oil odes A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon V 277V ommon ~ V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Line Voltage not listed: (i.e.: 480 and 575 VA) require a separate control source (i.e.: 120 VA). This item is available in the ORANGE E PRESS 3-day shipping program Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ This is a factory assembly. The KS7-0S1 (Q1) enclosure does not include knock-outs for field assembly of this starter. ➋ Uses D7P-U2EFFEPX11 Two-Position Multifunction push button with legend I/O. ➌ Uses D7P-MT44PX01 Emergency Stop Push Button. ➍ Refer to page 33 for wiring and dimensional information. This is a clam-shell enclosure design with wires to cover controls. ➎ Uses T7N or EP7-ED/EP7-EE overload. ➏ There is no room for additional auxilliaries. 21

9 / Reversing Series AUK A oils Three Phase Reversing with EP7 Overload Relays ➊ (KS7-0S4R) Auxiliary ontacts per ontactor ➐ ode 200V 230V 460V 575V NO N atalog Number ➌ FVR 3-Phase with A oil /2 1 1 AUK P 377 Q / AUK P 412 Q AUK P 437 Q / AUK P 463 Q3 oil odes (Q) ➍➏ A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon V 277V ommon ~ V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon Pilot Device Options (includes reset) ➋➎ Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option Replace in catalog number with See this page only Pushbutton Description FOR-STOP-REV Multi-function (shown) 3U Standard UP-STOP-DOWN Multi-function 4U Standard OPEN-STOP-LOSE Multi-function 5U Standard FOR-STOP-REV 3-Position Selector switch 6 Standard UP-OFF-DOWN 3-Position Selector switch 7 Standard OPEN-OFF-LOSE 3-Position Selector switch 8 Standard Overload Alarm Pilot Light 1Y Standard D7-N8 22mm Hole Plug 0 Standard Optional A7 Modifications (Factory Assembled) Description (supplied on each contactor) Add to end of catalog number Electronic Interface -2JE +188 Surge Suppressor RD Surge Suppressor Varistor -2V +108 ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Pilot lights are 240 VA maximum. Replace with one of the following Overload Relays For use with KWIKstarter... AUK AUK7-9E...23E AUK AUK7-9E...23E Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 3-Phase / Manual Reset / lass D1AB EP7-ED1AB Standard D1BB EP7-ED1BB Standard D1B EP7-ED1B Standard D1DB EP7-ED1DB Standard D1EB EP7-ED1EB Standard 3-Phase / Auto or Manual Reset / lass 10, 15, 20, EAB EP7-EEAB EBB EP7-EEBB EB EP7-EEB EDB EP7-EEDB EEB EP7-EEEB +17 ➊ Use EP7-ED/EP7-EE overloads only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 32 for wiring diagram and 34 for dimensional information. ➍ Other voltages available, see Section A. ➎ One Pilot Device option must be selected. Blanks are not available. If Pilot Light option is selected then coil voltage must be 24V, 120V or 240V A only. ➏ PT not possible with KS7-0S4R (Q3) enclosure. ➐ One N.. auxiliary contact is used for electrical interlocking. On AUK7 reversing starters, the N.. contact comes from the Mechanical/Electrical Interlock unit (at# M7-02). 22

10 / Reversing Series AUK Electronic D oils Three Phase Reversing with EP7 Overload Relays ➊ (KS7-0S4R) Auxiliary ontacts per ontactor ➐ ode 200V 230V 460V 575V NO N atalog Number ➌ FVR 3-Phase with Electronic D oil /2 1 1 AUK7-9E- - -P 451 Q / AUK7-12E- - -P 497 Q AUK7-16E- - -P 527 Q / AUK7-23E- - -P 559 Q3 oil odes ➍➏ D.. oil ode Voltage VD 12E 12V 24E 24V 36E 36-48V 48E 48-72V 110E V 220E V Pilot Device Options (includes reset) ➋➎ Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option Replace in catalog number with See this page only Pushbutton Description FOR-STOP-REV Multi-function (shown) 3U Standard UP-STOP-DOWN Multi-function 4U Standard OPEN-STOP-LOSE Multi-function 5U Standard FOR-STOP-REV 3-Position Selector switch 6 Standard UP-OFF-DOWN 3-Position Selector switch 7 Standard OPEN-OFF-LOSE 3-Position Selector switch 8 Standard Overload Alarm Pilot Light 1Y Standard D7-N8 22mm Hole Plug 0 Standard Optional A7 Modifications (Factory Assembled) Description (supplied on each contactor) Add to end of catalog number Electronic Interface -2JE +188 Surge Suppressor RD Surge Suppressor Varistor -2V +108 Replace with one of the following Overload Relays For use with KWIKstarter... AUK AUK7-9E...23E AUK AUK7-9E...23E Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 3-Phase / Manual Reset / lass D1AB EP7-ED1AB Standard D1BB EP7-ED1BB Standard D1B EP7-ED1B Standard D1DB EP7-ED1DB Standard D1EB EP7-ED1EB Standard 3-Phase / Auto or Manual Reset / lass 10, 15, 20, EAB EP7-EEAB EBB EP7-EEBB EB EP7-EEB EDB EP7-EEDB EEB EP7-EEEB +17 ➊ Use EP7-ED/EP7-EE overloads only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 32 for wiring diagram and 34 for dimensional information. ➍ A7-9E 55E with electronic coils are not interchangeable with non-electronic D or A coils. ➎ One Pilot Device option must be selected. Blanks are not available. If Pilot Light option is selected then coil voltage must be 24V D only. ➏ PT not possible with KS7-0S4R (Q3) enclosure. ➐ One N.. auxiliary contact is used for electrical interlocking. On AUK7 reversing starters, the N.. contact comes from the Mechanical/Electrical Interlock unit (at# M7-02). 23

11 NEMA Series AKN7 & BKN7 - A and Electronic D oils NEMA with T7N or EP7 Overload Relays ➊➏ over ontrol/ (KS7-0S1/0S4) oil odes ➎➐ NEMA Size Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ KWIKstarter with Start & Raised Stop with A oil ❹➎ 1/3 1 ~ ~ ~ ~ BKN P2 ~ ~ 1-1/2 1-1/2 2 2 AKN P2 515 Q1 1 2 ~ ~ ~ ~ BKN P2 ~ ~ AKN P2 554 Q1 KWIKstarter with Start & Raised Stop with Electronic D oil ➐ 1/3 1 ~ ~ ~ ~ BKN7-12E- - -P2 ~ ~ 1-1/2 1-1/2 2 2 AKN7-12E- - -P2 648 Q1 1 2 ~ ~ ~ ~ BKN7-16E- - -P2 ~ ~ AKN7-16E- - -P2 695 Q1 KWIKstarter with Reset with A oil 1/3 1 ~ ~ ~ ~ BKN P0 ~ ~ 1-1/2 1-1/2 2 2 AKN P0 477 Q1 1 2 ~ ~ ~ ~ BKN P0 ~ ~ AKN P0 515 Q1 KWIKstarter with Reset with Electronic D oil ➐ 1/3 1 ~ ~ ~ ~ BKN7-12E- - -P0 ~ ~ 1-1/2 1-1/2 2 2 AKN7-12E- - -P0 610 Q1 1 2 ~ ~ ~ ~ BKN7-16E- - -P0 ~ ~ AKN7-16E- - -P0 657 Q1 A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon V 277V ommon ~ V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon D.. oil ode Voltage VD 12E 12V 24E 24V ontrol ircuit Note ommon: oils are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils are assumed to be from a separate source and will not be connected to the line source per the table. This item is available in the ORANGE E PRESS 3-day shipping program Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ are designed for three-wire control circuits. Two-wire (maintain) control can be accomplished by adding pushbutton latch KS7-PLA. ➋ A special design NO auxiliary contact (at.# KS7-PK) is used as the holding circuit interlock, as well as, the START button interface. It is not available for other use. ➌ Refer to page 33 for dimensional information. ➍ STOP button also functions as RESET button. Plastic Bezel is standard. ➎ Other voltages available, see Section A. ➏ Use T7N or EP7-ED/EP7-EE overload. ➐ AN7-12E 16E with electronic coils are not interchangeable with non-electronic D or A coils. 24 Discount Schedule B8

12 NEMA Series AKN7 & BKN7 - A and Electronic D oils NEMA with T7N or EP7 Overload Relays with H-O-A and Light ➊➋➌➎➏ over ontrol/ (KS7-0S1) NEMA Size 00 0 Single Ø Total Aux. ontacts Installed 115V 230V 200V 230V 460V 575V NO N atalog Number ➍ NEMA KWIKstarter with Reset and H-O-A Selector Switch and Light with A oil 1/3 1 ~ ~ ~ ~ BKN P0+1R7 1 ➏ 0 ~ ~ 1-1/2 1-1/2 2 2 AKN P0+1R7 1 2 ~ ~ ~ ~ BKN P0+1R7 1 ➏ 0 ~ ~ AKN P0+1R7 ode 636 Q1 674 Q1 NEMA KWIKstarter with Reset and H-O-A Selector Switch and Light with Electronic D oil ➐ 00 1/3 1 ~ ~ ~ ~ BKN7-12E- - -P0+1R7 1 ➏ 0 ~ ~ 1-1/2 1-1/2 2 2 AKN7-12E- - -P0+1R7 796 Q ~ ~ ~ ~ BKN7-16E- - -P0+1R7 1 ➏ 0 ~ ~ AKN7-16E- - -P0+1R7 816 Q1 oil odes ➐ A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon D.. oil ode Voltage VD 12E 12V 24E 24V ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Line Voltage not listed: (i.e.: 480 and 575 VA) require a separate control source (i.e.: 120 VA). D7D pilot devices are rated 300 VA maximum. This item is available in the ORANGE E PRESS 3-day shipping program Specify atalog Number Replace (Q) with oil ode See this page See page 30 Important Note: are only designed to accommodate T7N Thermal Overload Relays or EP7 Solid State Overload Relays. Select O/L Relay ode from page 30. ➊ This is a factory assembly. The KS7-0S1 (Q1) enclosure does not include knock-outs for field assembly of this starter. ➋ Uses D7D-P4N_ Red Monolithic Run pilot light with LED bulb. Pilot light voltage to match coil voltage for 24, 120, 240 VA control. Red Run Light can be changed for Green. hange +1R7 to +1G7. For example, AKN P0+1R7 becomes AKN P0+1G7. ➌ Uses D7D-SM32x20 Monolothic 3-position selector switch for maintain control, HAND-OFF- AUTO function with legend plate. ➍ Refer to page 32 for wiring and dimensional information. This is a clam-shell enclosure design with wires to cover controls. ➎ Uses T7N or EP7-ED/EP7-EE overload. ➏ One NO auxilliary for customer use. There is no room for additional auxilliaries. ➐ AN7-12E 16E with electronic coils are not interchangeable with non-electronic D or A coils. Discount Schedule B8 25

13 NEMA Series AKN7 & BKN7 - A & Elec. 24VD oils NEMA with EP7 Overload Relays ➊ (KS7-2S4) NEMA Size Single Ø Total Aux. ontacts Installed ode 115V 230V 200V 230V 460V 575V NO N atalog Number ➌ NEMA with A oil 2 3 ~ ~ ~ ~ BKN ETD-P ~ ~ 7-1/2 7-1/ AKN P 3 7-1/2 ~ ~ ~ ~ BKN ETD-P ~ ~ AKN P NEMA with Electronic D oil ➍ 3 5 ~ ~ ~ ~ BKN7-37E- -ETD-P ~ ~ AKN7-37E- - -P 3 7-1/2 ~ ~ ~ ~ BKN7-43E- -ETD-P ~ ~ AKN7-43E- - -P 773 Q2 915 Q2 965 Q Q2 oil odes (Q) ➍➎➐ Voltage A.. Voltage ontrol Source D.. oil ode oil ode 50 Hz 60 Hz BK7 AK7 VD 24Z 24V 24V Separate Separate 12E 12V Replace with one of the following Overload Relays For use with KWIKstarter... AK AK Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 3-Phase / Manual Reset / lass D1D EP7-ED1D D1DD EP7-ED1DD D1ED EP7-ED1ED D1FD EP7-ED1FD +0 3-Phase / Auto or Manual Reset / lass 10, 15, 20, ED EP7-EED EDD EP7-EEDD EED EP7-EEED EFD EP7-EEFD +21 ➊ Use EP7-ED/EP7-EE overloads only. Single-phase applications utilize EP7S- EETD only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 31 for wiring diagram and 34 for dimensional information. ➍ AN7-37E 43E with electronic coils are not interchangeable with non-electronic D or A coils. A ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Pilot lights are 240 VA maximum V 120V ommon Separate 24E 24V 208 ~ 208V ~ ommon 36E 36-48V 220W 200V-220V 208V-240V ommon ommon 48E 48-72V V 240V ommon ommon 110E V V 277V ommon ~ 220E V V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon Pilot Device Options (includes reset) ➋➏ Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option Replace in catalog number with See this page only Pushbutton Description START-STOP Multi-function (shown) 3U Standard I-O Multi-function 4U Standard OFF-ON 2-Position Selector switch 6 Standard Pilot Light Red (LED) with START-STOP Multi-function 1R3U +50 Pilot Light Red (LED) with I-0 Multi-function 1R4U +50 Optional A7 Modifications (Factory Assembled) Description Add to end of catalog number Electronic Interface -JE +94 Surge Suppressor RD Surge Suppressor Varistor -V +54 Additional N ontact -L Additional NO ontact -L ➎ Other voltages available, see Section A. ➏ One and only one Pilot Device option must be selected. If Pilot Light option is selected then coil voltage must be 24V A or D, 120V or 240V A only. ➐ PT not possible with KS7-2S4 (Q2) enclosure. 26 Discount Schedule B8

14 NEMA / Reversing Series AUKN7 - A & Elec. 24VD oils Three Phase Reversing NEMA with EP7 Overload Relays ➊ (KS7-0S4R) NEMA Size Total Aux. ontacts Installed ode 200V 230V 460V 575V NO N atalog Number ➌ 3-Phase FVR NEMA KWIKstarter with A oil /2 1-1/ AUKN P 1136 Q AUKN P 1205 Q3 3-Phase FVR NEMA KWIKstarter with Electronic 24V D oil /2 1-1/ AUKN7-12E- - -P 1401 Q AUKN7-16E- - -P 1488 Q3 oil odes (Q) ➍➎➐ Voltage A.. Voltage ontrol Source D.. oil ode oil ode 50 Hz 60 Hz BK7 AK7 VD 24Z 24V 24V Separate Separate 12E 12V V 120V ommon Separate 24E 24V 208 ~ 208V ~ ommon 36E 36-48V 220W 200V-220V 208V-240V ommon ommon 48E 48-72V V 240V ommon ommon 110E V V 277V ommon ~ 220E V V-400V 440V ~ ommon V 480V ~ ommon V 600V ~ ommon Pilot Device Options (includes reset) ➋➏ Specify atalog Number Replace (Q) with oil ode Replace ( ) with Pilot Device Option Replace in catalog number with See this page only Pushbutton Description FOR-STOP-REV Multi-function (shown) 3U Standard UP-STOP-DOWN Multi-function 4U Standard OPEN-STOP-LOSE Multi-function 5U Standard FOR-STOP-REV 3-Position Selector switch 6 Standard UP-OFF-DOWN 3-Position Selector switch 7 Standard OPEN-OFF-LOSE 3-Position Selector switch 8 Standard Overload Alarm Pilot Light 1Y Standard D7-N8 22mm Hole Plug 0 Standard Optional A7 Modifications (Factory Assembled) Description (supplied on each contactor) Add to end of catalog number Electronic Interface -2JE +188 Surge Suppressor RD Surge Suppressor Varistor -2V +108 A ontrol ircuit Note ommon: oils and pilot devices in the control circuit are assumed to be common with the line voltage and will be connected to the line source (L1-L2) per the table. Separate: oils and pilot devices in the control circuit are assumed to be from a separate source and will not be connected to the line source per the table. Pilot lights are 240 VA maximum. Replace with one of the following Overload Relays For use with KWIKstarter... AUKN AUKN7-12E..16E AUKN AUKN7-12E..16E Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 3-Phase / Manual Reset / lass D1AB EP7-ED1AB Standard D1BB EP7-ED1BB Standard D1B EP7-ED1B Standard D1DB EP7-ED1DB Standard D1EB EP7-ED1EB Standard 3-Phase / Auto or Manual Reset / lass 10, 15, 20, EAB EP7-EEAB EBB EP7-EEBB EB EP7-EEB EDB EP7-EEDB EEB EP7-EEEB +17 ➊ Use EP7-ED/EP7-EE overloads only. ➋ Plastic Bezel is standard. Pilot Device options include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➌ Refer to page 32 for wiring diagram and 34 for dimensional information. ➍ AN7-12E 16E with electronic coils are not interchangeable with non-electronic D or A coils. ➎ Other voltages available, see Section A. ➏ One Pilot Device option must be selected. Blanks are not available. If Pilot Light option is selected then Pilot Light must match oil Voltage 24V A or D, 120V or 240V A only. ➐ PT not possible with KS7-0S4R (Q3) enclosure. ➑ One N.. auxiliary contact is used for electrical interlocking. On AUKN7 reversing starters, the N.. contact comes from the Mechanical/Electrical Interlock unit (at# M7-02). Discount Schedule B8 27

15 Series AK7/BK /AUK KWIKstarter 9 23A s with T7N or EP7 Overload Relays ➊➋ For Use With Environmental omponent Description ontactor Overload Approvals atalog Number Flush Green START / Extended Red STOP- Mechanical interface auxiliary contact (KS7-PK) included in enclosure. A T7N EP7-ED1 EP7-EE cul Type 1/12/4/4x IE KS7-OS4 123 Blue RESET Only A T7N EP7-ED1 EP7-EE cul Type 1/12/4/4x IE KS7-OS1 113 KWIKstarter s for use with A7 ontactors and Overload Relays ➊➎ omponent Description ontactor For Use With Overload Environmental Approvals atalog Number for KWIKstarter ➌ AK7/BK AK7/BK7-30E 43E A A7-30E 43E EP7-ED1D ED1FD EP7-EED EEFD EP7S-EETD cul Type 1/12/4/4x IE KS7-2S4 130 for Reversing KWIKstarter ➍ AUK AUK7-9E 23E AU AU7-9E...23E EP7-ED1AB ED1EB EP7-EEAB EEEB cul Type 1/12/4/4x IE KS7-0S4R 127 ➊ are only designed to accommodate A contactors with T7N Thermal Overload Relays or EP7 Solid State Overload Relays. If ordering components, select contactor from Section A and overload relay from Section B in this catalog. ➋ KS7-OS4 and KS7-OS1 may be used with either EP7 or T7N (field interchangeable). ➌ KWIKstarter enclosure KS7-2S4 are designed to fit A7-30(E) 43(E) contactors with EP7 Overload Relays. T7N Thermal Overloads can not be substituted. ➍ KWIKstarter enclosure KS7-0S4R are designed to fit AU7-9(E) 23(E) reversing contactors with EP7 Overload Relays. T7N Thermal Overloads can not be substituted. ➎ KS7-2S4 and KS7-0S4R are supplied with two 22mm holes for Pilot Devices. A Reset is required and one additional pilot device kit from page 29 must be selected. Use of a PT is not possible. 28

16 Series AK7 & BK7 KWIKstarter omponents with T7N or EP7 Overload Relays (for use with KS7-0S1/KS7-0S4) omponent Description For Use With... atalog Number Start - ontact kit Specially designed NO auxiliary; mechanically interfaces with the START button. Mounts on right side. A KS7-PK is included in every KS7-OS4 enclosure. Pushbutton Latch - For maintain contact control (2-wire control) KS7-OS4 (Replacement Part) KS7-PK 16 KS7-OS4 KS7-PLA 8 Neutral Terminal KS7-OS1 KS7-OS4 KS7-PNT 12 Grounding Kit (for use with metal conduit) All KWIKstarter enclosures KS7-GR1 13 KWIKstarter Pilot Device Kits (for use with KS7-2S4/KS7-0S4R) ➊ Kits Description Multi-Function Pushbutton kit Non-illuminated START-STOP I-O FOR-STOP-REV UP-STOP-DOWN OPEN-STOP-LOSE Selector switch kits Non-illuminated, includes legend plate ON-OFF 2-Position FOR-OFF-REV 3-Position UP-OFF-DOWN 3-Position OPEN-OFF-LOSE 3-Position For Use With... KS7-2S4 Type 1, 12, 4, 4X KS7-0S4R Type 1, 12, 4, 4X ontact Blocks included NO N atalog Number KS7-P3U KS7-P4U KS7-P3U-REV KS7-P4U-REV KS7-P5U-REV KS7-2S4 Type 1, 12, 4, 4X 1 - KS7-P6 40 KS7-0S4R Type 1, 12, 4, 4X 2 - KS7-P6-REV KS7-P7-REV KS7-P8-REV Reset Pushbutton, Blue Plastic push button, flush operator with Blue ap and R text KS7-2S4 KS7-0S4 Black Plastic with Blue ap and White R D7P-F611 ➋ See page H57 ➊ Plastic bezel is standard. Pilot Device Kits include D7-BX_ Base Mounted contact blocks. See page H69 for more information. ➋ D7P-R611 and EP7-ERA can not be used with KS7-2S4 or KS7-0S4R. See Section H for more information. 29

17 Series AK7 & BK7 with EP7 Solid State Overload Relay 3-Phase Application ➋➌ For use with KWIKstarter... Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 3-Phase / Manual Reset / lass D1AB EP7-ED1AB D1BB EP7-ED1BB +9 AK7-9...AK D1B EP7-ED1B D1DB EP7-ED1DB D1EB EP7-ED1EB +9 3-Phase / Selectable Function and lass EAB EP7-EEAB EBB EP7-EEBB +17 AK7-9...AK EB EP7-EEB EDB EP7-EEDB EEB EP7-EEEB +17 with EP7 Solid State Overload Relay 1-Phase Application ➋➌ For use with KWIKstarter... Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) 1-Phase / Selectable Function and lass EPB EP7S-EEPB +15 BK7-9...BK ERB EP7S-EERB ESB EP7S-EESB +15 with T7N Bimetallic Overload Relays ➊ For use with Kwikstarter... AK7-9...AK7-23 and BK7-9...BK7-23 Frame A Amp Overload Relay ode ( ) atalog Number (of Overload Relay used) AA16 T7N-23-A16 Standard AA25 T7N-23-A25 Standard AA40 T7N-23-A40 Standard AA50 T7N-23-A50 Standard AA63 T7N-23-A63 Standard AA80 T7N-23-A80 Standard AB10 T7N-23-B10 Standard AB13 T7N-23-B13 Standard AB16 T7N-23-B16 Standard AB20 T7N-23-B20 Standard AB25 T7N-23-B25 Standard AB32 T7N-23-B32 Standard AB40 T7N-23-B40 Standard AB48 T7N-23-B48 Standard AB63 T7N-23-B63 Standard AB75 T7N-23-B75 Standard A10 T7N Standard A12 T7N Standard A16 T7N Standard A20 T7N Standard A21 T7N Standard A25 T7N Standard This item is available in the ORANGE E PRESS 3-day shipping program ➊ If using T7N in single phase application with BK7-9 23, wire per drawing on page 31. ➋ EP7 Overloads are available for use in KWIKStarters if the premium features are required (see Section B). ➌ 3-phase EP7-ED or EP7-EE units are only designed for 3 applications. Single phase EP7S units are only designed for 1 applications. If using EP7S, wire per drawing on page

18 Wiring Diagrams KWIKstarter (in enclosure KS7-0S1/0S4) USTOMER MUST PROVIDE PROPER BRANH IRUIT PROTETION (F1) SEE THE APPLIATION INSTRUTION SHEET - OMPONENT SELETION TABLES FOR MAX. FUSE SIZE & LASS AND APPLIABLE SHORT IRUIT RATING (USE 75º OPPER WIRE ONLY) THIS DRAWING IS FOR THE FOLLOWING ENLOSURES: KS7-0S4 with integrated START-STOP push buttons KS7-0S1 with integrated RESET push button NOTES: 1) MEHANIAL LATH KS7-PLA FOR MAAINTAINED ONTROL (OPTIONAL). 2) START ONTAT KIT KS7-PK (INLUDED) MOUNTS ON THE RIGHT SIDE WITH MOLDED PRE-FORMED JUMPERS. 3) DO NOT WIRE ONTROLS IRUIT TO LINE SIDE OF ONTATOR WHEN OIL VOLTAGE IS 120V OR LESS. (FATORY WIRING STANDARD) 4) OPTIONAL PILOT LIGHTS. KWIKstarter (in enclosure KS7-2S4) 31

19 [10mm] 1 Inch SALE: Wiring Diagrams Reversing KWIKstarter (in enclosure KS7-0S4R) KWIKstarter (in enclosure KS7-0S1) with HOA option HAND-OFF-AUTO with Pilot Light [8.19] 111 [4.37] 27.9 [1.10] A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon D.. Voltage ontrol Source oil ode VD BK7 AK7 12E 12V Separate Separate 24E 24V Separate Separate 32

20 [10mm] 1 Inch SALE: [10mm] 1 Inch SALE: s EMERGENY STOP with MULTI-FUNTION KWIKstarter (in enclosure KS7-OS1) with Emergency Stop option [8.19] 111 [4.37] 32.1 [1.26] A.. Voltage ontrol Source oil ode 50 Hz 60 Hz BK7 AK7 24Z 24V 24V Separate Separate V 120V ommon Separate 208 ~ 208V ~ ommon 220W 200V-220V 208V-240V ommon ommon V 240V ommon ommon KWIKstarter KS7-0S1/0S4 ( ode Q1) s are in millimeters (inches). s not intended for manufacturing purposes Extended STOP [0.99] 19.5 [0.77] 44.5 [1.75] [8.19] 188 [7.41] [0.94] [1.24] 188 [7.41] 205 [8.08] ø5.3 [ ø0.21] ø20.3 [ ø0.80] 51 [2.01] 23.7 [0.94] 36.5 [1.44] 60.3 [2.38] 68 [2.68] 36.5 [1.44] 188 mm Ø " 0.2" DIA 97.9 [3.86] 111 [4.37] 5.5 [0.22] 111 [4.37] ø25.3 [ø 1.00] [0.22] Pozidriv No. 2 (1.2 x 6.5) 2.0 Nm 18 lb-in 2 x mm² 2 x No AWG Pozidriv No Nm 20 lb-in 33

21 s KWIKstarter KS7-2S4 ( ode Q2) s are in millimeters (inches). s not intended for manufacturing purposes. 125 [4.93] 125 [4.93] 16 [0.63] 250 [9.85] 169 [6.66] 13 [0.51] 3.5 [0.14] Ø23 [Ø0.91] [4.48] 235 [9.26] 78 [3.07] 30 [1.18] 50 [1.97] 110 [4.33] 125 [4.93] 50 [1.97] 24 [0.95] 28.1 [1.11] Rotary operator alternatively (for maintained control) 50 [1.97] 10 Pozidriv No. 2 (1.2 x 6.5) 2.0 Nm 18 lb-in 2 x mm² 2 x No AWG Pozidriv No Nm 20 lb-in KWIKstarter KS7-0S4R ( ode Q3) 125 [4.93] 125 [4.93] 16 [0.63] 250 [9.85] 13 [0.51] 3.5 [0.14] 235 [9.26] Ø23 [Ø0.91] 100 [3.94] [4.39] 30 [1.18] 88.6 [3.49] 50 [1.97] 110 [4.33] 125 [4.93] 50 [1.97] 28.1 [1.11] 50 [1.97] Rotary operator alternatively (for maintained control) 24 [0.95] 10 Pozidriv No. 2 (1.2 x 6.5) 2.0 Nm 18 lb-in 2 x mm² 2 x No AWG Pozidriv No Nm 20 lb-in 34