ODU-MAC in the Aluminium Frame

Transcription

1 ODU-MAC ODU-MAC in the The ODU-MAC in the aluminium frame is used exclusively for automatic docking. For manual mating, see ODU-MAC in the DIN housing, starting on page 91. Page 83

2 Part Number System for All Sizes The part number for all frames is composed of the following information: The first three digits indicate if the item is a pin frame or a socket frame. Digits 4 to 6 indicate the frame model (type S, M, P, etc.). Digits 7 to 9 indicate the number of units and consequently the frame length (total length of the modules). The example shows a pin frame (611) in the standard model (020) with a length of 14 units (014). No. Frame 611 Pin frame 6 Socket frame No. Model 020 S (standard) 009 (longer version) 017 M (reduced constructed space) 030 P (power contacts) No. Units Height of the Pins for All Frame Sizes ( and Solid Frame) Pin diameter Socket diameter 21 max / All pins project 6 mm ( 1 ). Protruding earth pins have a projecting length of 8 mm ( 2 ). The diameters of the pins or sockets are as follows: 0.76 mm 1.02 mm 1.50 mm 2.41 mm 3.00 mm 4.00 mm 5.00 mm Other lengths and diameters are available in special modules (coaxial, power, etc.)! Page 84

3 Requirements for the Guidance and Tolerances Between Wall B and Wall S for ODU-MAC S (Standard Model) The values apply to the mated state (pin S in B) and result from the axial play of the centring sockets. The customer is responsible for the strain relief! ODU-MAC socket piece (fixed) (screwed tightly to wall B without floating situation) Pin for guidance of wall B and S Cyl. screw Centring socket Axial floating: 0.2 mm Radial floating: ± 0.6 mm Pins only for the ODU-MAC s own centring ODU-MAC pin piece, floating (screwed tightly to wall S with play via the centring socket) Note: Automatic docking processes The pin piece of the ODU-MAC S is to be fastened to the accompanying centring sockets and consequently has a floating mounting. The guide system of the ODU-MAC does not provide any guidance for the overall slide-in module. There must be a certain advance guidance by means of the slide-in unit (e.g., by means of guidance rails, etc.). The max. permitted misalignment is, e.g., for the ODU- MAC S frame, less than ± 0.6 mm radial. A tilting of max. 4 in the connector s longitudinal direction and 2 in the connector s transverse direction is permissible. The max. permissible gap between the socket piece and the pin piece is 0.5 mm. Page 85

4 ODU-MAC ODU-MAC S, Standard Version Socket frame without guiding pin Pin frame with guiding pin A max. R4 +,5 +0,2 Axial floating: 0.2 Radial floating: ±0.6 for M4 Pin frame XX Socket frame XX Dimension A mm Notice Pin frame XX Socket frame XX = Number of units 2.54 Pin frame XX Socket frame XX Pin frame XX Socket frame XX For spindle locking With labelling XX = for entering the number of required units (03 60) Page 86

5 ODU-MAC Special Model with Elongated Guiding Pins and Guiding Sockets for Greater Radial Floating (Number of units ) max. R M 4 Unmated Mated Axial floating 0.2 mm, radial floating ±1.2 mm Equipping example + 46 Pin frame XX = number of units 2.54 Socket frame XX XX = for entering the number of required units 32 coding positions are possible on request. Page 87

6 ODU-MAC M Pin Frame and Socket Frame for More Compact Spaces Pin frame 3,2 20-0, ,1 max. R , Pin frame XX = number of units 2.54 XX = for entering the number of required units 30 +0,1 max. R for M3 Socket frame for M3 Socket frame XX = number of units 2.54 XX = for entering the number of required units Page 88

7 ODU-MAC P Pin Frame and Socket Frame for Power Contacts and More Stringent Mechanical Requirements Pin frame ,3 Socket frame 42 6, ,6 7, max. R ,6 +48, Axial floating 0.5 mm Radial floating +/ 1.25 mm Floating mounting reliable offset of pin piece and socket piece 2.5 mm Pin frame XX Socket frame XX = Number of units 2.54 XX = for entering the number of required units (05 60) Special use, if a number of power contacts are installed within an ODU-MAC connector. This frame is recommended for a contact diameter of 5 mm or more. This frame must be used for a contact diameter of 8 mm or more. Units: from 5 to 60 onger and thicker guiding pins: 7.8 mm / 25 mm long Attachment with M6 screws With labelling for M Page 89