B-Client PDC6. Manual /2013 EN

Transcription

1 B-Cliet PDC6 Maual /2013 EN

2 Copyright by Kaba GmbH Workforce Maagemet Albertistraße 3 D Villige-Schweige Phoe /603-0 Fax / All rights reserved. The documet ad its parts are copyrighted. Oly Kaba GmbH has the right to commercialize, market ad distribute this documet. This documet, or ay part of it, may ot be copied or reproduced, adapted, arraged, reworked or modified without the prior coset of Kaba GmbH. All compay, trademark or product ames are trademarks or registered trademarks of their respective owers ad are protected. Subject to techical chages without otice! Order o /2013

3 1 About this maual Product descriptio Optio cocept Licesig Memory partitioig Commuicatio Commuicatio cocept Upload/Dowload Operatig mode Olie Offlie Autoomous Group ID (GID) ad device ID (DID) File trasfer via FTP File trasfer via FTP Procedure from the host computer s poit of view Procedure from the termial s poit of view Remote cotrol via FTP Remote cotrol usig commad records Parameter settig via dowload ad settigs i the.ii files Hexadecimal iterpretatio of characters Editig the commuicatio settigs Commuicatio via HTTP/HTTPS/XML HTTP/HTTPS/XML: Abbreviatios used i the text Data ecryptio via HTTPS Specificatio of system variables XML traslatio file XML cofiguratio file XML: Establishmet of the commuicatio Iitializatio of the b-cliet_xml.ii file XML: Olie/Offlie mode XML: Recorded data codig XML: Bookig resposes XML: Troubleshootig Fuctio keys Master records Time profiles Basic data record structure Explaatio of abbreviatios Geeral termial parameters Buffer Backup Logical group address (GID) Logical device address (DID) Respose timeout Dowload record Buffer backup ad logical idetificatio Switchover from stadard time (witer) to daylight savig time Secods i data record User laguage i the data record Dowload record Stadard time/daylight savig time switchig Display time Authorized" Display time "Not authorized" Display time Display ifo... 62

4 Pull-i time relay User timeout Dowload record "Duratios" PIN for biometrics maagemet Character set idetificatio Fuctio key parameters Acoustic sigal Fuctio key as iput filter Termial awaits logical bookig respose i offlie ad autoomous mode Key repeat fuctio Idividual master record required Activate Authorized relay Bookigs allowed i offlie / autoomous mode Buffer recordig data Show persoal text Suppress display ifo i master record Fuctio key as dialog key Cotet of the G8-record Check o time authorizatio Number of display ifo Dowload record Fuctio key parameters Fuctio key fuctios Record type/record type modificatio Display data of the iput uit Iput uits Recordig data umeric/alphaumeric Keyboard iput rollig/fix Keyboard allowed Check for iput legth Number of digits From digit Text o Default settigs of the fuctios keys Limit value o Release iput uit Eter recordig data ito data record Use sigle fuctio block Positive acustic cofirmatio after reader iput Covered iput Dowload record sigle fuctio blocks Limit value pairs Duplicatio fields Lists List o Idex i list List text o Data field Dowload record lists Fuctio key cotrol Fuctio key switchover Fuctio key o Dowload record fuctio key cotrol Relay cotrol Switch-o time relay Relay o Operatio time Dowload record relay cotrol...103

5 2.21 Time profiles Profile ame Time zoe Validity days Idetificatio bytes Dowload record time profiles Special day table Date idicatio Special day idetificatio Dowload record special day table Texts Fuctio key texts Dialog texts Fix-Texte Geeral texts Texts for register tabs Mailbox texts Display ifo texts List texts Dowload record compatible ad multiligual texts Data records from the host to the termial Display records Dialog records (G dialog) G dialog compariso to fixed bookig procedure G dialog procedure Termial settigs for G-dialog records G dialog example Dialog mask Dialog iput Dialog request Dialog ed Termial cotrol Request status of the iputs Block / release bookigs Local biometrics maagemet eabled/blocked Block / release dialog Relay cotrol Switchig termial i Olie, Offlie, Autoomous mode Requestig recordig data i the Autoomous operatig mode Requestig termial state Requestig program o. ad serial o Requestig backup state Deletig backup state Requestig reader iformatio Buffer cotrol Logical bookig respose Bookig authorized with display ifo (R4 to R6-record) Date / time Master records Idividual master record dowload Idividual master record deletio Idividual master record request Idividual master record dowload ed Pseudo master record dowload Pseudo master record deletio...159

6 3.7.7 Pseudo master record request Pseudo master record dowload ed Parameter dowload/upload Parameter upload request Parameter up / dowload record Ed of parameter dowload Data records from termial to computer Recordig data Error records Status records Reportig program o Report status of iputs Buffer memory empty / Buffer memory full Local biometrics maagemet start/stop Report termial status Report backup state Report reader iformatio Master records Upload of idividual master record Upload of pseudo master record Ed of idividual/pseudo master record upload Parameter upload/dowload Parameter upload record Ed of parameter upload Kaba Mifare proximity reader Geeral Kaba Mifare overview: cofiguratios Kaba Mifare overview: Card hierarchy ad iheritace Kaba Mifare: Term defiitio Applicatio cases Maagig the istallatio keys Dowloadig the istallatio key Result of istallatio key dowload Deletig idividual istallatio key Result of idividual istallatio key deletio Deletig all istallatio keys Result of deletig all istallatio keys Distributig istallatio keys by meas of programmig masters A ad B Disablig/eablig the istallatio key trasfer Distributig the istallatio key ad reportig the check sum Distributig the istallatio key ad reportig the paret ifo Exchagig productio key agaist applicatio key Reportig exchage of productio key agaist applicatio key Tables Record types/record type modificatio for data records host termial Record types/record type modificatio for data records termial - host Table of block idetificatios Table of clock idetificatios Table of parameter settig errors Table of error idetificatios Table of laguage idetificatios Table of characters accordig to ISO ISO (Lati 1) ISO (Lati 2)...210

7 5.8.3 ISO (Cyrillic) ISO (Moder Greek) Table of characters Chiese Table of characters Japaese Table of characters Thai Table of characters Arabic Table of ISO 646 character sets ASCII table ii-files system.ii HID iclass reader: Cofiguratio examples mediaact.ii mediadef.ii Defiitio of coversio parameters bedaet.ii b-cliet_pdc6.ii debug.ii Notes Bouds Fot Aligmet Image Size Period Idex...249

8

9 Maual About this maual Pos: 1 /KABA Kapitel (SW)/PDC6 Module/Allgemeies, Programmstad, About this maual Validity This maual describes the Kaba applicatio B-Cliet PDC6 as of B-Cliet PDC6 ERP Cliet B-Cliet PDC6 Parter Cliet Date of maufacturig: February 2013 Firmware versio: X-K00 Firmware versio: X-K00 Addressees The explaatios refer to qualified ad skilled persos, they ca ot substitute for product traiig. Special kowledge about the costructio of cofiguratio files (.ii files) are absolutely ecessary. Cotet ad purpose The cotet of this maual is limited to the descriptio of the sigle parameter- or data records ad the possible etries i the various.ii files. The user shall be eabled to activate the desired fuctio via parameter records whe usig his ow parameter settig software. Additioal mauals Commuicatio software: B-COMM Java maual Istallatio, set-up ad operatio of the B-eco hardware: B-eco maual. Modificatio log First editio of this maual i February Orietatio i the maual This maual cotais the followig orietatio guide to fid specific topics more easily: The table of cotets at the begiig of the maual gives a overview of all topics. The header always cotais the respective mai chapter. A idex i alphabetical order is at the ed of the maual. B-Cliet PDC /2013 9

10 About this maual Maual Remarks with symbols Please pay special attetio to the remarks that are marked with symbols. Tips ad useful iformatio. This iformatio will help you to best use the product ad its fuctioality. Notice Importat iformatio for proper hadlig of the product. Igorig this iformatio ca cause device malfuctio. Step-by-step istructio A certai fuctio is explaied i a step-by-step istructio. Ifo Iformatio Lik(s) that lead(s) to further iformatio of the described topic /2013 B-Cliet PDC6

11 Maual About this maual 1.1 Product descriptio Depedig o the licesed software optios, the applicatio B-Cliet PDC6 i coectio with the termial B-eco offers a wide rage of fuctioality. Fiftee customizable data collectio processes with a maximum of 18 iput steps each List fuctioality Multi-ligual user iterface i four laguages maximum Supports ISO , , ad charactersets. Supports Arabic, Japaese, Chiese ad Thai character sets Mailbox fuctio Display of up to te display ifo texts Numeric key for eterig idividual data or PINs Variable legth of ID umber ad PIN Operatig modes olie, offlie, autoomous Supports various readers like Legic advat, barcode, HID iclass, Mifare etc. Remote cotrol XML commuicatio possible Kaba Mifare proximity reader with ART cocept Software updates ca be easily realized via Iteret, Itraet, or Extraet. The biometrics fuctioality metioed i this maual is curretly ot implemeted. Therefore, all associated biometric parameters are ot eabled. B-Cliet PDC /

12 About this maual Maual 1.2 Optio cocept B-Cliet PDC6 cosists of several fuctioal uits itegrated as idividual optios i the device software. Each of these optios covers a certai fuctioal area ad ca be activated after purchasig a correspodig licese. This allows idividual adjustmet of the fuctioal scope of the software to the existig coditios or customer requiremets. The activatio of a optio ca also be performed subsequetly. This allows to adjust B-Cliet PDC6 easily to chaged coditios at ay time. Whe startig the B-Cliet PDC6, a etry is created for every optio i the log file (../Data/B-ClietPDC6/Diagosis/debug.log). This maual describes all possible optios ad their coectio to each other. Every parameter or data record has a colored ico used to specify what optio is required for its use. Certai fuctios may require the use of several optios. This must be observed whe orderig the correspodig licese(s). If ot-licesed fuctios are called via dowload or ot-licesed parameters are accessed i the bookig sequece, error text is output o the display (default: Parameter settig error). I additio, a O5 record is geerated ad set to the host. A etry ito the log file../debug.log is ot created Licesig The required fuctios ca be activated at ay time usig the optio cocept i the software. A valid licese file (sop.ii) must be trasmitted via FTP ito the directory /Programs/Share/Iit. After the trasmissio has bee completed, depedig o the licesed optio the termial must be restarted as follows: Cold start Memory optios Warm start Digital Iputs/Outputs Local erollmet Ecryptio For licesig optios that chage the umber of master records or the legth of the badge umber or PIN code or the memory cofiguratio, a cold start must always be performed. All master records available i the termial are deleted durig this process. Perform a backup of all data stored i the termial before licesig oe of these optios /2013 B-Cliet PDC6

13 Pos: 2 @ 1 Maual About this maual The possible optios ad their properties are listed i the followig table. Ico Desigatio Descriptio M I/O LEN User (Memory) Digital I/Os Local Erollmet The user optios are used to licese the required umber of master records i the termial. This also applies to update ad validatio records for the optio CardLik. A table with possible memory cofiguratios is give i chapter The optio cotais the fuctios for the use of the digital I/Os. Activatig of relay R1 Moitorig the iputs E1 ad E2 The biometrics optio is ot available at the momet. EN Data Ecryptio The optio icludes ecrypted data exchage usig host chael via HTTPS or UDP Memory partitioig M The umber of the possible master records/bookigs depeds o the purchased licese, see followig table. The default settig is BufferCofiguratio0. No separate licese is required for this (factory settig). With the BufferCofiguratio2 optio, it is also possible to adapt the partitioig of the master records ad bookigs by meas of a etry i the bcliet_pdc6.ii file. Memory optio (licese) Master records Bookigs Memory BufferCofiguratio BufferCofiguratio BufferCofiguratio BufferCofiguratio MB SRAM For licesig optios that chage the umber of master records or the legth of the badge umber or PIN code or the memory cofiguratio, a cold start must always be performed. All master records available i the termial are deleted durig this process. Perform a backup of all data stored i the termial before licesig oe of these optios. B-Cliet PDC /

14 Commuicatio Maual Pos: 3 /KABA Kapitel (SW)/PDC6 Module/Kommuikatio Commuicatio The followig chapters cotai the followig topics: basic explaatios about the commuicatio betwee termial ad host descriptio of up- ad dowload termial addressig ad operatig modes parameter settig via FTP parameter settig via dowload records editig the EEPROM settigs via FTP 2.1 Commuicatio cocept The commuicatio betwee a host computer ad the termials is ormally carried out via a etwork. Termial software B-Cliet PDC6 Commuicatiosoftware B-COMM Applicatio LAN Termial Host Fig. 1: Host commuicatio via etwork Data exchage betwee the termial software ad the applicatio program takes place by meas of the commuicatio software B-COMM. Applicatio program ad commuicatio software ca be istalled o the same computer or o differet computers. The commuicatio software trasmits the data records recorded by the termials to files or trasmits them to the applicatio via a defied iterface. Data such as user iformatio, time ad date or persoal master records ca be trasmitted from the host to a termial. The parameter settig of the termials ca be maaged cetrally o the host ad trasmitted to the termials. The termial ca be operated i the olie, offlie ad autoomous operatig modes. The data exchage of the termials with the host is doe i the same maer. Likewise, the commuicatio orders are awarded i the correspodig file /2013 B-Cliet PDC6

15 Maual Commuicatio 2.2 Upload/Dowload The data trasfer descriptios i this maual ofte use the terms upload ad dowload. They are defied as show below. Dowload: Host Termial Upload: Termial Host Dowload Upload Fig. 2: Dowload/Upload 2.3 Operatig mode Data records from ad to the termial cotai a digit that describes the mometary operatig mode of the device. I data records trasmitted from the host to the termial, this digit may be filled with a blak (20hex). The operatig mode is represeted by ASCII characters accordig to the followig table. Operatig mode ASCII Hex Olie Blak 20 Offlie Ifo Topic Switchig the operatio mode B-Cliet PDC /

16 Commuicatio Maual Olie The olie operatig mode is advisable if the data to be recorded must be permaetly available i the host. After a bookig has bee made, the termial carries out the checks ad writes the test result as error idetificatio ito the iput record. The data record is trasmitted to the host computer. After that the termial expects a logical bookig respose from the host. With this respose the termial is iformed by the host if the bookig is authorized or ot. If the termial does ot receive a logical bookig respose from the host, it will chage to the offlie operatig mode ad decide itself if the bookig is authorized or ot. As soo as the host computer is accessible agai, the termial will chage back to the olie mode. All data records stored i the meatime i the offlie mode will be trasmitted to the host Offlie The offlie mode is recommeded if the recorded data does ot have to be permaetly available. After a bookig has bee made, the termial carries out the checks ad decides immediately by way of a iteral bookig respose if the bookig is authorized or ot. If the host is available, the data records of authorized ad uauthorized bookigs (depedig o the set parameters) are trasmitted. Otherwise, the data records will be stored i the termial. As soo as the host computer is available, all data records stored sice the last trasmissio are trasmitted to the host Autoomous After a bookig has bee made, the termial carries out the checks ad decides immediately by way of a iteral bookig respose if the bookig is authorized or ot. Data records of authorized or uauthorized bookigs are stored i the termial, depedig o the set parameters. If the host is available, ay existig error ad alarm records are trasmitted to the host. The stored data records are trasmitted to the host i a special data record after beig requested. The data records trasmitted to the host are the deleted i the termial, depedig o the settig of the Buffer Backup parameter. Ifo Topic Buffer Backup /2013 B-Cliet PDC6

17 Maual Commuicatio 2.4 Group ID (GID) ad device ID (DID) A device is idetified by the group ad device IDs. The first two digits of the data record always cotai the termial idetificatio. Logical Group Address = GID = Group-ID, allowed values 00 through 29. Logical Device Address = DID = Device-ID, allowed values 00 through 59. The group idetificatio (GID) ad the device idetificatio (DID) are represeted by ASCII characters accordig to the followig table. Adr ASCII Hex Adr ASCII Hex ^ 5E 01 A F 02 B ` C a D b E c F d G e H f I g J 4A 40 h K 4B 41 i L 4C 42 j 6A 13 M 4D 43 k 6B 14 N 4E 44 l 6C 15 O 4F 45 m 6D 16 P E 17 Q o 6F 18 R p S q T r U s V t W u X v Y w Z 5A 56 x [ 5B 57 y \ 5C 58 z 7A 29 ] 5D 59 { 7B B-Cliet PDC /

18 Commuicatio Maual 2.5 File trasfer via FTP Geeral For easy ad efficiet data trasfer, a FTP server is itergrated i the B-Cliet PDCx software. This feature is automatically loaded by a etry i the [Programs] sectio of the bedaet.ii file whe startig the applicatio. This is particularly efficiet whe large quatities of data must be distributed to a large umber of termials. The trasfer of a cotrol file ca effect a remote-cotrolled restart of the termial. The termial cotais several INI files whose settig ca also be adjusted by meas of access via FTP. FTP users ad their properties ca be admiistrated i the ftpuser file i the Program/Share/User directory. The followig user are cofigured: Userame: Password: Note: root Bedaet The user root has full access to directories ad files of the applicatio. Userame: Password: Note: localuser Bedaet No access to directories ad files above the Ram/Trasfer directory. Ifo Topic 6.4 The file bedaet.ii Reemote cotrol of the termial /2013 B-Cliet PDC6

19 Maual Commuicatio ftpuser The format of the user etries will ow be illustrated usig the default etries as a example. root ; Bedaet ; false ; / ; ; 2 ; localuser ; Bedaet ; true ; /Ram/Trasfer ; ; 1 ; User ame 2 Password 3 Access to root directory oly, true = yes, false = o 4 Root directory 5 Reserved 6 Level (userlevel) 0 through 9 The idividual parameters are eded with a semicolo ";". There are o blaks betwee the idividual characters. Example: root;bedaet;false;/; ;2; localuser;bedaet;true;/ram/trasfer; ;1; filelevels.ii The filelevels.ii file is i the Program/Share/Iit/ directory.especially protected directories ad files ca be etered ito this file. Example: /Data/testfile=2 Access to the /Data/testfile file is oly possible for users of level >= 2. B-Cliet PDC /

20 Commuicatio Maual File trasfer via FTP File trasfer via FPT is a parameter settig optio that avoids direct commuicatio with the termial. The parameters are stored i a file i the described format ad the trasferred to the termial via FTP. If the applicatio rus o the termial, it will read the parameters from the file. All files eeded for data trasfer are stored i the Ram/Trasfer directory. The trasferrig method uses oly two files: a data file ("record.zip" or "record.dat") ad a cotrol file ("iput.cmd ).If the data file is preset i both formats, oly the zipped versio is used. The uzipped file is ot cosidered i this case. The data file cotais the parameter records ad the master records. The data records begi with the GID/DID ad are separated by a carriage retur character. The files geerated by B-COMM software ca be used if you delete the first lie which cotais the program umber. The cotrol file is a empty file, oly its existece o the termial is checked Procedure from the host computer s poit of view First, the host has to check the existece of the cotrol file. This is the case if either the last data trasfer is ot fialized or a problem occurred while readig the data file. If o cotrol file exists, first the data file must be trasferred ad after that the cotrol file. If doe, the data trasfer is fiished for the host s poit of view. To review the success of the data trasfer, the deleted cotrol file iput.cmd idicates, that all records were read. I this case, all data records were processed successfully Procedure from the termial s poit of view If the applicatio rus, the termial checks periodically (every 10 secods) the existece of the data file. If it exists, the data file is read ad all data records are processed oe after aother. The processig takes place i the same way as if the data records were received via the ormal commuicatio chael. After processig the last record, the data file will be deleted. I the last step, the cotrol file is deleted to provide a success message. The termial is ow ready for the ext trasfer /2013 B-Cliet PDC6

21 Maual Commuicatio Remote cotrol via FTP It is possible to execute oe of the fuctios listed below from a remote PC. This is doe by copyig the defied file i the /Ram/Trasfer/ directory via FTP. It may lasts up to te secods util the desired file will be executed. Before executio the file will be deleted. Fuctio File ame File cotet Start service mode reboot.cmd SERVICE the etry SERVICE starts the termial i service mode. Restart applicatio reboot.cmd RESET the etry RESET restarts the termial applicatio Remote cotrol usig commad records The followig commad records eable the cotrol to carry out some special fuctios: TASERVICE TARESET or TARESET COLD resp. TAFTP or TAFTP START resp. TAFTP STOP The commad to be executed must be writte directly ito the comad record. GID DID ON/OFF T A.... Group address Device address Betriebszustad Record type Record type modificatio Commad, see followig table. Commad SERVICE RESET RESET COLD FTP FTP START FTP STOP Descriptio The termial applicatio is closed ad the service mode is started. (See service mode maual). The termial applicatio is closed ad restarted agai. The defied parameters remai uchaged. After dowload a cold restart of the device takes place. After dowload the FTP server is started. After dowload the FTP server is started. After dowload the FTP server is stopped. B-Cliet PDC /

22 Commuicatio Maual 2.6 Parameter settig via dowload ad settigs i the.ii files The various fuctios of the termial maily deped o the parameters you set. Parameter settig allows the termial to be adapted to most user requiremets. Whe settig a termials parameter, the existig parameters are modified ad the ew values are stored i the termials memory. Parameter settig via dowload is doe by trasmittig data records from a computer to the termial. To do so, the so-called dowload records are trasmitted to the termial.. The followig chapters explai the type of records you ca dowload. After you cold start a termial i service mode, all parameters are reset to their default values (please refer to the termial documetatio regardig service mode). The parameters i the.ii files ca be trasmitted to the host via FTP ad be modified the. Ifo Topic 6 Compilatio of the.ii-files Hexadecimal iterpretatio of characters Some dowload records offer the possibility to select parameters by etry of hexcoded values. These records are explaied precisely with separate tables, i which the possible values are defied. The bits marked with Reserved have o fuctio. Example: The parameters of bit 2 ad 3 are to be set Hex validity Bit Biary value Biary writig of this value: Decimal coversio: 1x8 + 1x4 + 0x2 + 0x1 = 12 dec Hex chart: Hex value A B C D E F Decimal Value that is iscribed i the data record: C This bit codig meas: bit 2 ad bit 3 are set, i.e. the fuctios defied here are activated /2013 B-Cliet PDC6

23 Pos: 4 @ 1 Maual Commuicatio 2.7 Editig the commuicatio settigs The devices settigs for host- ad termial commuicatio are stored i its EEPROM memory. The settigs ca be uploaded via FTP by help of the /Ram/EEPROMsettig file, editited with a text editor ad the sed back to device cotaiig ew settigs The followig graph shows the 2 possible optios: Upload the "EEPROMsettig file via FTP" Optio A: editig the commuicatio settigs without immediate restart - reame the file to "reboot.cmd" - make the desired chages - store the file to the Ram/Trasfer directory i the device. Optio B: editig the commuicatio settigs with immediate restart - reame the file to "reboot.cmd" - isert the "RESET" commad i the first lie of the file - make the desired chages - store the file to the Ram/Trasfer directory i the device. Further process: - after processig the "reboot.cmd" file, the parameters are stored iterally. For loggig reasos, the parameter.old ad parameter.ew files will be created. The ew parameters take effect after a restart. Further process: - after processig the "reboot.cmd" file, the device will be resartet. The ew parameters will be take over to the EEPROMsettig file. Fig. 3: Chagig the commuicatio settigs If the commad sytax is icorrect at oe positio, the whole ew parameters will ot be take over. A respective etry will be made i the debug.err error file. B-Cliet PDC /

24 Pos: 5 /KABA Kapitel (SW)/PDC6 Module/HTTP(S) @ 1 Commuicatio Maual 2.8 Commuicatio via HTTP/HTTPS/XML The HTTP/HTTPS/XML commuicatio is iteded for the olie commuicatio betwee termial ad server. The occurrig data records are marked up as XML files ad set to the server ad/or termial via HTTP/HTTPS. Ulike the other commuicatio paths (e.g. UDP) the termial is the active side i the HTTP/HTTPS/XML commuicatio ad iitializes the commuicatio. That meas that data records or requests caot be set simply from the server to the termial. I fact, they must be set from the termial i a bookig respose to a request. Requests to the server are uecrypted via the HTTP method GET". Operatig subtermials with a HTTP/HTTPS/XML commuicatio is ot possible. Settig of the HTTP/HTTPS/XML commuicatio is doe by meas of the service mode of the termial. More detailed iformatio about the service mode is to be foud i the Service Mode maual. Before a HTTP/HTTPS/XML commuicatio to the server ca be established the followig files must exist o the server: the traslatio file (default ame: xmltras.xml, see chapter 2.8.4). the cofiguratio file (default ame: xmlcofig.xml, see chapter 2.8.5). The file ames i this documetatio always refer to the default settigs. File ames ca deviate i real istallatios. I the examples, URLs are used i the HTTP format. I case of ecrypted data traffic, this must be HTTPS. The HTTP/HTTPS/XML commuicatio ca also be established via a proxy server. I this case, the correspodig parameters for the proxy server (port ad IP address) must be set i the service mode of the termial /2013 B-Cliet PDC6

25 Maual Commuicatio HTTP/HTTPS/XML: Abbreviatios used i the text HTTP/HTTPS XML RSA SSL/TLS RFC PKI DSA DH CRL SHA1 Hypertext trasfer protocols (usecured/secured). Markup laguage for ecodig data i a textual format. Asymmetric ecryptio system used for data ecryptio ad digital sigatures. Network protocol for secured data trasmissio. Numbered seria of documets cocerig iteret related techical ad orgaizatioal topics. System that issues, distributes ad verifies certificates. US stadard about digital sigatures. Diffie-Hellma key exchage algorithm. List of ivalid certificates. Stadardized, cryptologic hash fuctios Data ecryptio via HTTPS HTTPS: Geeral The iteret protocol HTTPS was desiged to provide secure data exchage via the iteret. It serves for the ecryptio of the commuicatio betwee web servers ad cliets. Compared to the usecured protocol HTTP, HTTPS uses SSL (Secure Socket Layer) or its successor TLS (Trasport Layer Security) as trasport layer protocols. The data ecryptio betwee Kaba termials ad the web servers take place i two steps: Exchage of certificates to authorize the commuicatio parters Exchage of sessio keys to ecrypt the user data. I the followig chapters you will fid iformatio about requiremets ad limitatios o the certificate exchage. The ecryptio of the user data is doe i the backgroud. For maximum security we recommed the use of 128-bit ecryptio algorithms if the system performace allows this. Durig the operatio, a combiatio of secured ad usecured data traffic is possible at the same time. Before establishig the secured data traffic it is recommeded to check all the coectios without ecryptio first. B-Cliet PDC /

26 Commuicatio Maual HTTPS: Properties of the certificates The keys to be used may have a legth of 512, 1024, 2048 or 4096 bit. The legth of the sigle certificates i a certificatio chai may differ. The certificates must meet the followig requiremets: The certificate must be i UTF-8 format (Uix text format). The character strig -----BEGIN CERTIFICATE----- is madatory at the begiig of the certificate. The character strig -----END CERTIFICATE----- is madatory at the ed of the certificate. Root certificates of a certificatio authority must be siged by the CA itself. The "CN" (= Commo Name) field i the server certificate must cotai either the IP-address of the server (e. g. CN= ) or its DNS ame (e. g. CN=abcdefg). If the DNS ame is defied, the IP address of the DNS server must be defied i the termial. The DNS server must be available for the termial. The certificatio chai may ot exceed 3 certificatio levels icludig the ed etity (= the web server). The server certificate must ot have ay extesios marked as critical. The certificates of the certificatio authority must have the BasicCostrait extesio marked as critical (Parameter CA=true). No further extesio is allowed to be marked as critical. Extesios which are marked as ucritical will be igored. If oly oe of these requiremets is ot met, o coectio to the server ca be established. The termial will the remai i the "Offlie" operatig mode /2013 B-Cliet PDC6

27 Maual Commuicatio HTTPS: Properties of the termial I the Kaba termial the followig requiremets must be met for the ecryptio of the data traffic: The software optio "Ecryptio" must be eabled i the termial. This is ot the "EableEcryptio" checkbox i the service mode. The XML commuicatio must be activated i the termial. A subdirectory /SSL must exist i the termials /Data directory. If ecessary, this directory must be geerated: /Data/SSL. The certificate authority root certificate must be stored i the /Data/SSL directory. The file ame root.pem for the certificate is madatory. Please observe the followig limitatios whe creatig ad usig certificates. These limitatios are summarized i two groups ad are show i the followig tables. Limitatios regardig the TLS/SSL implemetatio 1. B-Net termials ca oly work as SSL/TLS cliets. 2. B-Net termials as SSL/TLS cliet support oly server autheticatio. 3. The protocol versio SSL 2.0 is ot supported. 4. The protocol versio TLS 1.1 is ot supported. 5. The protocol versio TLS 1.2 is ot supported. 6. The protocol versios SSL 3.0 ad TLS 1.0 with the followig algorithms are supported: Algorithm Key Ecryptio algorithm Checksum SSL_RSA_EXPORT_WITH_RC4_40_MD5 RSA_Export RC4_40 MD5 SSL_RSA_WITH_RC4_128_MD5 RSA RC4_128 MD5 SSL_RSA_WITH_RC4_128_SHA RSA RC4_128 SHA SSL_RSA_EXPORT_WITH_RC2_CBC_40_MD5 RSA_Export RC2_CBC_40 MD5 SSL_RSA_EXPORT_WITH_DES40_CBC_SHA RSA_Export DES40_CBC SHA SSL_RSA_WITH_DES_CBC_SHA RSA DES_CBC SHA SSL_RSA_WITH_3DES_EDE_CBC_SHA RSA 3DES_EDE_CBC SHA TLS_RSA_EXPORT_WITH_RC4_40_MD5 RSA_Export RC4_40 MD5 TLS_RSA_WITH_RC4_128_MD5 RSA RC4_128 MD5 TLS_RSA_WITH_RC4_128_SHA RSA RC4_128 SHA TLS_RSA_EXPORT_WITH_RC2_CBC_40_MD5 RSA_Export RC2_CBC_40 MD5 TLS_RSA_EXPORT_WITH_DES40_CBC_SHA RSA_Export DES40_CBC SHA TLS_RSA_WITH_DES_CBC_SHA RSA DES_CBC SHA TLS_RSA_WITH_3DES_EDE_CBC_SHA RSA 3DES_EDE_CBC SHA 7. TLS 1.0 does ot support the extesio from RFC TLS 1.0 does ot support the additioal cipher suites from RFC 2712, RFC 4132 ad RFC B-Cliet PDC /

28 Commuicatio Maual Limitatios regardig the PKI certificates 1. B-Net termials support oly X.509v3 certificates. 2. B-Net termials support oly RSA ad RSA_EXPORT key exchage methods ad cosequetially all certificates must be siged with ad cotai oly RSA keys. DSA keys ad DH key exchage methods are ot supported. 3. B-Net termials support RSA keys of 512, 1024, 2048 ad 4096 bits. 4. B-Net termials support oly SHA1 certificate sigatures. 5. B-Net termials igore "Uique Idetifiers" as defied i RFC 2459 but will accept certificates holdig these properties. 6. I geeral, Ed Etity (web server) certificates must ot have ay extesios except o critical oes which will be igored. 7. B-Net termials support oly "BasicCostrait" extesios as defied i RFC B-Net will igore the followig extesios but will accept certificates holdig these extesios: a. Authority key idetifier b. Subject key idetifier c. Private key usage period d. Subject directory attributes e. Policy mappigs f. Key usage extesio (if marked as ot critical) g. Certificate policies (if marked as ot critical) h. Subject alterative ame (if marked as ot critical) i. Issues alterative ame (if marked as ot critical) j. Exteded key usage (if marked as ot critical) 9. CRL fuctioality will ot be supported /2013 B-Cliet PDC6

29 Maual Commuicatio HTTPS: Properties of the server The web server must meet the followig limitatios for the ecryptio of the data traffic: A iteret iformatio server (IIS.6) uder WIN 2003 must be istalled. The settig of the "Coectio Timeout" parameter of the IIS server must be as twice as the settig of the "CHECKONLINETIME" parameter i the termial. You fid these settigs as described below: - Coectio Timeout: i the "WebSites" tabs of the "Web Site Properties" meu of the IIS. Default value: 120 secods. - CHECKONLINETIME: i the "Commo" sectio of the "b-cliet_xml.ii" file of the termial. Default value: 60 secods. At least oe of the protocols SSL 3.0 or TLS 1.0 must be activated. I case of both protocols are activated, TLS 1.0 will be used. Host Header are ot supported ad must ot be used. Please observe the followig limitatios whe creatig ad usig certificates. These limitatios are summarized i two groups ad are show i the tables i chapter HTTPS: Troubleshootig The tables i this chapter show possible errors, their causes ad resolutio. The error texts ca be fid i the file "Debug.log/Debug.err. Errors relatig to the termial Error text E:SSLHadshake.recvCertificate(): TLS_ALERT_UNKNOWN_CA Cause/Troubleshootig The certificate i the "root.pem" file does ot fit to the certificate the server certificate has bee created with. The certificate is ot readable. a) it is ot i the UTF-8 format b) it does ot have the required structure. B-Cliet PDC /

30 Commuicatio Maual Errors relatig to the server Error text C:bezig.et.SSLProxyCoector I:Could ot establish proxy coectio to :8080 E:TLS_ALERT_BAD_CERTIFICATE(VERIFY ): CN does ot match: !=, CN=abcdef C:bezig.et.protocol.https.Coectio I:Could ot coect to: https: Cause/Troubleshootig Check whether the proxy server is ready for operatio ad HTTPS is permitted o the proxy server. Check the DNS settigs. I the give example, the server ame is defied as "CN=abcdef". I the DNS server, the IP address is defied for the server "abcdef). Check whether the server accepts the termials IP address (o IP filterig) either SSL3.0 or TLS 1.0 or both protocols are activated. Certificatio error Error text E:SSLHadshake.recvCertificate(): TLS_ALERT_UNKNOWN_CA E:TLS_ALERT_BAD_CERTIFICATE(VERI FY): CN does ot match: !=, CN=abcdef C:bezig.et.protocol.https.Coec tio I:Could ot coect to: https: E:SSLHadshake.recvCertificate(): TLS_ALERT_BAD_CERTIFICATE(VERIF Y): Basic costraits for a CA must be critical E:SSLHadshake.recvCertificate(): TLS_ALERT_BAD_CERTIFICATE(VERIF Y): Basic Costraits ot preset Cause/Troubleshootig The server certificate was ot geerated accordig to the X.509v3 stadard. The value i the "CN=" field (i the example: abcdef) does ot correspod with the IP address or the DNS ame of the server. The server certificate exceeds the umber of certificatio levels which is limited to 3. The server certificates validity has expired. Error of the certificatio authority. The "BasicCostrait" parameter does exist but is ot marked as critical. Solutio: chage the certificatio authority or request a ew root certificate that meets the requiremets. Error of the certificatio authority. The "BasicCostrait" parameter does ot exist. Solutio: chage the certificatio authority or request a ew root certificate that meets the requiremets /2013 B-Cliet PDC6

31 Maual Commuicatio Certificatio error Error text E:SSLHadshake.recvCertificate(): TLS_ALERT_BAD_CERTIFICATE(VERIFY): Basic Costraits preset i sigig cert but ot a CA E:SSLHadshake.recvCertificate(): TLS_ALERT_BAD_CERTIFICATE(VERIFY): Critical extesio ot allowed! E:SSLHadshake.recvCertificate(): TLS_ALERT_BAD_CERTIFICATE(VERIFY): User certificate ot allowed to be CA Cause/Troubleshootig Error of the certificatio authority. The "BasicCostrait" parameter does exist ad is marked as critical but is set to CA=false. Solutio: chage the certificatio authority or request a ew root certificate that meets the requiremets. Error either of the certificatio authority or the server certificate. A extesio other tha "BasicCostrait" is marked as critical. Solutio: chage the settigs ad geerate a ew certificate. Error of the server certificate. The "BasicCostrait" parameter of the server certificate is set to "true". Solutio: geerate a ew certificate with CA=false. B-Cliet PDC /

32 Commuicatio Maual Specificatio of system variables The termial provides a set of pre-defied system variables with fixed fuctios for the HTTP/XML commuicatio. The system variables are partly stored i the EEPROM of the termial ad partly i the sectio Commo of the b-cliet_xml.ii file, to have the settigs available if the system must be restarted. All system variables ca be chaged at rutime via XML pages except the variables SERIALNUMBER ad MACADDRESS which are read-oly. Whe usig the system variables observe the otatio! Whe usig ecrypted commuicatio, oly sytax 1 is permitted! The system variables ca also be used i URL requests to trasmit iformatio to the server. I these cases, the fact that a variable ad ot a text is cocered must be made clear by the itroductory character $ ad the ame of the variable i brackets. Example: $(GID) is replaced by the value of the GID system variable. The followig list cotais all system variables ad their meaig. System variables i EEPROM Systemvariable Possible values Descriptio GID 0-29 Default: 0 The GID is used for the idetificatio of a termial group. It must be set with iitial startup of the termial. DID 0-59 Default: 0 The GID is used for the idetificatio of a idividual termial withi a termial group. It must be set with iitial start-up of the termial. PROXY ONLINEIP IP address: Port umber Default: empty IP address: Port umber Default: :8080 IP address of the proxy server, followed by a colo ad specificatio of the port umber for commuicatio with the termial. IP address of the olie server, followed by a colo ad specificatio of the port umber for commuicatio with the termial. It must be set with iitial start-up of the termial /2013 B-Cliet PDC6

33 Maual Commuicatio System variables i the sectio Commo of the b-cliet_xml.ii file System variable Possible values Descriptio TERMTYP Character strig Default: curret program umber The specificatio i TERMTYP defies the termial type ad is ecessary for program start. SERIALNUMBER MACADDRESS Character strig Default: curret serial umber Character strig i the format: xx.xx.xx.xx.xx.xx Example: 0C-FF-34-5A-23-1B Default: curret MAC address Serial umber of the termial. This value is read-oly. MAC address des Termials. This value is read-oly. SYSTIME YYYYMMDDHHMMSS The time o the termial is set by meas of the SYSTIME variables. This correspods to sedig of a U1 record. INITIAL_XMLTRANSLATION Sytax 1: or Sytax 2: File ame Default: xmltras.xml The rest of the call will be added automatically. Name of the XML traslatio page which is requested by the server durig the program start. Sytax 1: Defies a complete URL i the format http or https. System variables may be used with this call as eeded. The ampersad character (&) must be etered as a <&> strig. ml?gid=$(gid)&did=$(di D)&TERMTYP=$(TERMTYP )&SERIALNUMBER=$(SERI ALNUMBER)&MACADDRE SS=$(MACADDRESS). Sytax 2: The call has the followig fixed structure: MLTRANSLATION)?GID=$(GID) &DID=$(DID)&TERMTYP=$(TER MTYP)&SERIALNUMBER=$(SERI ALNUMBER)&MACADDRESS=$( MACADDRESS). B-Cliet PDC /

34 Commuicatio Maual System variables i the sectio Commo of the b-cliet_xml.ii file System variable Possible values Descriptio INITIAL_XMLCONFIG Sytax 1: or CHECKONLINETIME CHECKOFFLINETIME Sytax 2: File ame Default: xmlcofig.xml The rest of the call will be added automatically. Numerical data Default: 60 Numerical data Default: 10 Name of the XML cofiguratio page which is requested by the server durig the program start. Sytax 1: Defies a complete URL i the format http or https. System variables may be used with this call as eeded. The ampersad character (&) must be etered as a <&> strig. ml?gid=$(gid)&did=$(did )&TERMTYP=$(TERMTYP)&a mp;serialnumber=$(serialnu MBER)&MACADDRESS=$(M ACADDRESS). Sytax 2: The call has the followig fixed structure: MLCONFIG)?GID=$(GID)&DID=$( DID)&TERMTYP=$(TERMTYP)&SE RIALNUMBER=$(SERIALNUMBER )&MACADDRESS=$(MACADDRE SS). Time i secods withi which the termial checks the availability of the server i operatig mode "Olie". Time i secods withi which the termial checks the availability of the server i operatig mode "Offlie" /2013 B-Cliet PDC6

35 Maual Commuicatio CHECKONLINEPAGE Sytax1: or Sytax 2: File ame Default: ukow.htm The rest of the call will be added automatically. Defies the page which is requested periodically by meas of CHECKONLINETIME i termial operatig mode "Olie". Sytax 1: Defies a complete URL i the format http or https. System variables may be used with this call as eeded. The ampersad character (&) must be etered as a <&> strig. page.xml?gid=$(gid)&did =$(DID)&TERMTYP=$(TERM TYP)&SERIALNUMBER=$(SE RIALNUMBER)&MACADDRE SS=$(MACADDRESS). Sytax 2: The termial software prefixes the file ame with the call B-Cliet PDC /

36 Commuicatio Maual System variables i the sectio Commo of the b-cliet_xml.ii file System variable Possible values Descriptio CHECKOFFLINEPAGE ERRORPAGE Sytax1: or Sytax 2: File ame Default: ukow.htm The rest of the call will be added automatically. Sytax1: or Sytax 2: File ame Default: error.xml The rest of the call will be added automatically. Defies the page which is requested periodically by meas of CHECKOFFLINETIME i termial operatig mode "Offlie". Sytax 1 ad sytax 2 as for CHECKONLINEPAGE. Name of the XML error page which is requested by the termial whe a error occurs. Sytax 1: Defies a complete URL i the format http or https. System variables may be used with this call as eeded. The ampersad character (&) must be etered as a <&> strig. D=$(GID)&DID=$(DID)&am p;termtyp=$(termtyp)&s ERIALNUMBER=$(SERIALNUMBE R)&MACADDRESS=$(MACA DDRESS). Sytax 2: The call has the followig fixed structure: E)?GID=$(GID)&DID=$(DID)&TER MTYP=$(TERMTYP)&SERIALNUM BER=$(SERIALNUMBER)&MACAD DRESS=$(MACADDRESS)&DATA =$(BPA,1)&ERROR=<Text> /2013 B-Cliet PDC6

37 Maual Commuicatio XML traslatio file The traslatio file (default ame: xmltras.xml) serves as traslatio table for the occurrig data records. This table must cotai a defiitio for each RT/RTM to be edited. The traslatio table must be available o the server with establishmet of the commuicatio with the termial. If the traslatio file does ot exist at this poit, the termial cotiues to establish the commuicatio every 60 secods. The termial requests the traslatio table via the system variable INITIAL_XMLTRANSLATION while startig the termial applicatio. The traslatio table ca be edited whithi the operatig time ad dowloaded to the termial as a attachmet of ay bookig respose. It must me assured to dowload oly complete traslatio tables, ot oly the chages made. Editig the traslatio table may be ecessary i the followig cases: chages i the structure of the bookig record chages i the assigmet of the fuctio keys. A ew traslatio table dowloaded with a bookig respose replaces the existig traslatio table. The traslatio table must be itroduced with the tag <tras> ad termiated with the tag </tras>. The actual traslatio regulatios are i a CDATA area. The CDATA area is withi the character strig <![CDATA[ Cotet ]]>. The reactio o data records based o the RT/RTM is defied i the cotet of the traslatio table. For this, the traslatio defiitios are specified by XML tags which cosist of the RT/RTM of a data record ad the URL statemet, see example defiitio. Fig. 4: Example defiitio of a traslatio table. B-Cliet PDC /

38 Commuicatio Maual Suppress data records Data records ca be suppressed, depedig o their RT/RTM. To do so, the RT/RTM to be suppressed must be defied with a empty URL, see the examples below. If a RT/RTM with a empty URL occurs, o http request will be sed to the server. The geerated data record will be deleted. <?xml versio="1.0"?> <tras> <![CDATA[ <B1> <URL= &MODE=$(BPA,2,1)&SASAM=$(BPA,3,2)&TIMESTAMP=$ (BPA,6,10)&ID=$(BPA,17,13)/> </B1> <B2> <URL= &MODE=$(BPA,2,1)&SASAM=$(BPA,3,2)&TIMESTAMP=$ (BPA,6,10)&ID=$(BPA,17,13)/> </B2> Examples: <A0> <URL=/> </A0> <B3> <URL=/> </B3> ]]> </tras> Fig. 5: Example: Suppressed RT/RTM with empty URL /2013 B-Cliet PDC6

39 Maual Commuicatio Defiig a geeral operatig rule All udefied RT/RTMs ca be treated accordig to a geeral operatig rule. This rule is defied by a tag with the wildcard characters * * ad a respective URL. Example 1: All udefied RT/RTMs are treated accordig to the defiitios which take place i the defied URL (page ukow.xml ). Example 2: The URL defiitio i example 2 is empty. This way, all udefied RT/RTMs are suppressed. If ay of these RT/RTM occurs, o http request will be sed to the server. The geerated data records will be deleted. <?xml versio="1.0"?> <tras> <![CDATA[ <B1> <URL= PA,2,1)&SASAM=$(BPA,3,2)&TIMESTAMP=$(BPA,6,10)&ID=$(BPA,17,13 )/> </B1> Example 1 <**> <URL= </**> Example 2 <**> <URL=/> </**> ]]> </tras> Fig. 6: 2 examples of geeral operatig rules for udefied RT/RTMs. B-Cliet PDC /

40 Commuicatio Maual The data itself is specified i a code i the URL request to the server. I additio to the system variables (e.g. GID/ DID, ONLINEIP etc.) the keyword BPA is available. It specifies Die Date selbst werde i der URL-Afrage a de Server codiert agegebe. from which digit ad how may digits of the data withi the data record are iserted i the URL request. Example: RTRTM=$(BPA,7,10): the record type/record type modificatio is iserted at digit 7 ad comprises 10 digits. If o umber of digits is specified, all the digits are iserted, startig with the specified digit to the ed of the data record. ID=$(BPA,7): all the digits of the ID umber are iserted startig with digit 7 to ed of the data record. Example defiitio for a fuctio key with RT/RTM I (B1): <B1> <URL= &SASAM=$(BPA,4,2)&TIMESTAMP=$(BPA,7,10)&ID=$(BPA,18)/> </B1> The B1 bookig o the termial results i the followig URL request o the server (assumig the termial is ready for operatio, that meas the cofiguratio file has already bee requested ad trasmitted, see chapter 2.8.5). &RTRTM=B1&TIMESTAMP= &ID= Defiitio etry Meaig Protocol defiitio Server IP address 8080 Server port umber i.xml GID=5 DID=5 MODE=0 SASAM=B1 Name of the XML file for the bookig respose to be called Group address of the termial Device address of the termial Operatig state of termial Record type/record type modificatio of the actuated fuctio key (B1= I ) TIMESTAMP= Time stamp, 10 digits startig with digit 7 (BPA,7,10) ID= Badge data, all digits startig with digit 18 (BPA,18) /2013 B-Cliet PDC6

41 Maual Commuicatio XML cofiguratio file The cofiguratio file (default ame: xmlcofig.xml) cotais cofiguratio data of the termial. It must be available o the server with establishmet of the commuicatio with the termial. If the cofiguratio file does ot exist at this poit, the termial cotiues to establish the commuicatio every 60 secods. The termial requests this file with start of the termial applicatio via the system variable INITIAL_XMLCONFIG. The cofiguratio file must be itroduced with the tag <cfg> ad termiated with the tag </cfg>. The system variables ca be specified straight as variables i the sysvar objects by meas of ame ad value. The parameters ad data records of the termial applicatio are specified i the sysdef objects by meas of the variables TERMREC ad value. Fig. 7: Example of a cofiguratio filebeispiel eier Kofiguratiosdatei B-Cliet PDC /

42 Commuicatio Maual XML: Establishmet of the commuicatio For the establishmet of a commuicatio betwee termial ad server the followig prerequisites must be met: The iterface ETH/XML has bee selected i the termial The traslatio file is o the server (see chapter 2.8.4) The cofiguratio file is o the server (see chapter 2.8.5) The commuicatio is established based o the followig scheme: Server Termial Default IP: Default server IP: Host ETH/XML set additioal default parameters (e..g. port umber) Request: INITIAL_XMLTRANSLATION Aswer Traslatio file. Default: "xmltras.xml" Request: INITIAL_XMLCONFIG Cofiguratio file. Default: "xmlcofig.xml" Parameters i the termial are set accordig to the specificatios i the cofiguratio file. Aswer Trasmissio of the cofiguratio file Fig. 8: First establishmet of the commuicatio for XML commuicatio After the commuicatio has bee fiished the termial received the XML traslatio file ad the commuicatio parameters from the cofiguratio file ad is ready for operatio. Errors durig the XML startup process The XML commuicatio will ot be started if a error occurs durig the start process, e.g. the server aswer to the request of the XML traslatio file is missig. I this case, the start process ad the server request is repeated every 60 secods /2013 B-Cliet PDC6

43 Maual Commuicatio Iitializatio of the b-cliet_xml.ii file Factory settig The b-cliet_xml.default file is i the directory /Program/B-Clietxxx/Iit ( xxx ca be HR1, HR2, HR3, PDC1, PDC3, PDC4, PDC6 or PDC10). This file cotais all factory settigs. With a cold start this file is copied ad stored as b-cliet_xml.ii file i the directory /Data/B-Clietxxx/Iit. Customer-specific settigs are made i the b-cliet_xml.ii file i the directory /Data/B-Clietxxx/Iit. The cold start deletes this file ad cosequetly the customerspecific settigs. Data retetio after cold start Shall the customer-specific settigs be retaied after a cold start, the b-cliet_xml.ii file ca be stored i the directory /Program/B-Clietxxx/Iit. This file is a copy of the b-cliet_xml.ii from the directory /Data/B-Clietxxx/Iit ad cotais the settigs made by the user. If a cold start is performed ow, the system first searches for the file b-cliet_xml.ii i the directory /Program/B-Clietxxx/Iit ad loads it after b-cliet_xml.ii i directory /Data/B-Clietxxx/Iit. If the b-cliet_xml.ii file is ot foud i the directory /Program/B-Clietxxx/Iit, the b-cliet_xml.default file i directory /Program/B-Clietxxx/Iit is loaded istead. This esures that the customer-specific settigs ca be maitaied ad the factory-set default values are available. START Yes No b-cliet_xml.ii i Data? Yes No b-cliet_xml.ii i Program? Copy b-cliet_xml.ii from Program to Data. Yes No b-cliet_xml.default i Program? Copy b-cliet_xml.default from Program to Data ad reame it to b-cliet_xml.ii. Yes No Create b-cliet_xml.ii i Data with the default values. END Fig. 9: Iitializatio of the b-cliet_xml.ii file B-Cliet PDC /

44 Commuicatio Maual XML: Olie/Offlie mode XML: Olie mode I a established coectio betwee termial ad server (termial mode olie), the termial checks the availability of the server periodically. This is doe by meas of a URL request (CHECKONLINEPAGE) to the server to the port which is defied i the parameter ONLINEIP. The time iterval (i secods), i which the termial trasmits the URL request is defied by the system variable CHECKONLINETIME. With these URL requests the termial attempts to establish a coectio to the server ad requests the file which is stored i the system variable CHECKONLINEPAGE. Subsequetly the coectio is closed. The graph below illustrates this process. No periodical requests will take place if the system variable CHECKONLINETIME is set to 0. I this case the termial switches automatically to "Offlie". Termial Periodically withi the secods defied with the "CHECKONLINEPAGE" parameter" Request: "CHECKONLINEPAGE" Trasmissio "CHECKONLINEPAGE" Server File which is defied i the "CHECKONLINEPAGE" parameter" Trasmissio og the file which is defied i the "CHECKONLINEPAGE" parameter" Fig. 10: XML: Olie mode /2013 B-Cliet PDC6

45 Maual Commuicatio XML: Offlie mode If there is o coectio betwee the termial ad the server ay loger, the termial switches temporarily to offlie mode. This happes automatically after elapse of the time CHECKONLINETIME or if there is o bookig respose from the server. The termial ow records all bookig data i offlie mode ad attempts at regular itervals to establish a coectio with the server. This is doe by meas of a URL request (CHECKOFFLINEPAGE) to the server to the port which is defied i the parameter ONLINEIP. The termial trasmits data usig the GET method ad requests the file which is stored i the system variable CHECKOFFLINEPAGE. Subsequetly the coectio is closed. The time iterval (i secods) i which the termial trasmits the URL requests is defied by meas of the system variable CHECKOFFLINETIME. Whe the server is available agai, the termial gets a respose to the CHECKOFFLINEPAGE request ad switches to olie mode. Subsequetly the coectio is closed. The graph below illustrates this process. Termial Periodically withi the secods defied with the "CHECKOFFLINEPAGE" parameter" Request: "CHECKOFFLINEPAGE" Trasmissio "CHECKOFFLINEPAGE" Server File which is defied i the "CHECKOFFLINEPAGE" parameter" Trasmissio of the file which is defied i the "CHECKOFFLINEPAGE" parameter" Fig. 11: XML: Offlie mode B-Cliet PDC /

46 Commuicatio Maual XML: Recorded data codig The recorded data record for the respective fuctio key results from the defiitio i the traslatio file; see example i chapter With post-processig of the data it must be take ito accout that the termial applicatio performs a so-called percetage codig of all characters with the exceptio of the o-reserved characters. Table of the ot-reserved characters Hex value Character 41-5A Characters A - Z 61-7A Characters a - z Characters 0-9 2D - 2E. 5F _ 7E ~ The followig applies Codig is doe for all characters which are other characters tha ot reserved (reserved or laguage-related special characters) ad which occur i the so-called Query block of the recorded data record, i.e. after the questio mark ad which occur withi the recorded data These characters are coverted percetage-coded that meas the character is represeted by specificatio of its hexadecimal values with prefixed % character. XML: Example of a recorded data record: &TIMESTAMP= &ID=020&00000)001 I the represeted URL request the query block starts with the questio mark i frot of the GID. I the recorded data the characters "&" ad ")" are displayed Codig: & is coded: %26; ) is coded: %2A The character & occurrig i the character strig &amp is ot coverted as it is ot withi the recorded data /2013 B-Cliet PDC6

47 Maual Commuicatio XML: Bookig resposes XML: Olie aswers I olie mode all data which were recorded with a bookig are trasmitted as XML page to the server by usig the GET method. I this process a defiitio is made i the traslatio table, which XML page is requested as bookig respose for this bookig. Example with the data record from chapter &TIMESTAMP= &ID= I the example the XML page i.xml is requested as bookig respose for a bookig with RT/RTM B1 (I). The page i.xml might have the followig cotets: <?xml versio="1.0"?> <dialog> <sysdef ame= TERMREC R1Thak you /> <sysdef ame= SYSTIME value= /> </dialog> Fig. 12: XML: Example for bookig aswer The bookig aswer must be itroduced with the tag <dialog> ad termiated with the tag </dialog>. The system variables ca be specified straight as variables i the sysvar objects by meas of ame ad value. The parameters ad data records of the termial applicatio are specified i the sysdef objects by meas of the variables TERMREC ad value. I this maer, requests e.g. for program umber or master records to the termial ca be trasmitted together with the bookig aswer, ad text ca be edited, etc. If there is o defiitio for the correspodig RT/RTM stored i the traslatio file, the termial applicatio seds the data by meas of the error page ERRORPAGE (default: error.xml) to the server (see chapter ). I this case, the behavior of the termial applicatio is the same as for a missig bookig respose. The termial waits the time defied i the parameter Respose time-out (approx. 12 secods by default, see chapter ) ad the decides o the authorizatio. B-Cliet PDC /

48 Commuicatio Maual XML: Offlie aswers The data arise i offlie mode are trasmitted to the server by usig the GET method after the server is available agai. The XML page requested as bookig aswer is the same as i olie mode because the bookig aswer is defied i the traslatio table by the RT/RTM. If there is o defiitio for the correspodig RT/RTM stored i the traslatio file, the termial applicatio seds the data by meas of the error page ERRORPAGE (default: error.xml) to the server (see chapter ) XML: Dialog aswers I dialog mode the dialog records are trasmitted to the server by meas of the GET method. The requested XML page is described by a defiitio i the traslatio table, like for the fuctio keys. The RT/RTM of the (G) dialog records are used for this. <tras> <![CDATA[ <G8> </G8> <G1> </G1> ]]> </tras> <URL= &DID=$(DID)&SASAM=$(BPA,3,2) &DATA=$(BPA,5,2)/> <URL= &DID=$(DID)&1)&SASAM=$(BPA,3,2) &DATA=$ (BPA,5,5)/> Fig. 13: XML: Example defiitios for dialog mode /2013 B-Cliet PDC6

49 Maual Commuicatio The server trasmits the XML page which is specified i the traslatio table as dialog aswer. The page g8.xml (see example defiitio) might cotai the followig: <?xml versio="1.0"?> <dialog> <sysdef ame= TERMREC G Eter Code /> </dialog> Fig. 14: XML: Example for dialog aswer The bookig aswer must be itroduced with the tag <dialog> ad termiated with the tag </dialog>. The system variables ca be specified straight as variables i the sysvar objects by meas of ame ad value. The parameters ad data records of the termial applicatio are specified i the sysdef objects by meas of the variables TERMREC ad value. I this maer, requests e.g. for program umber or master records to the termial ca be trasmitted together with the bookig aswer, ad text ca be edited, etc. If there is o defiitio for the correspodig RT/RTM stored i the traslatio file, the termial applicatio seds the data by meas of the error page ERRORPAGE (default: error.xml) to the server (see chapter ). B-Cliet PDC /

50 Commuicatio Maual XML: Troubleshootig Troubleshootig is doe by the XML error page which is defied i the system variable ERRORPAGE (default ame: error.xml). The termial requests the XML error page from the server whe a error occurs. The recorded data are trasmitted together with the request. For XML/HTTP commuicatio 3 differet error types are defied: Error i the RT/RTM defiitio of the traslatio table BPA error i the traslatio table After request of the error page the data record is deleted from the termial buffer, o matter whether the server aswered. The termial logs all errors which could ot be treated by meas of the ERRORPAGE i the debug.log file XML: RT/RTM error If the defiitio for RT/RTM is ot foud i the traslatio table or if it is faulty, the termial applicatio requests the error page as follows: &TERMTYP=$(TERMTYP)&SERIALNUMBER=$(SERIALNUMBER)&MACADDRESS=$( (<RTRTM>) I this process the recorded data are trasferred with the keyword DATA startig with digit 1 (=$[BPA,1]). The request cotais a additioal descriptive text (ERROR=RTRTMNotFoud) ad a idicatio o the RT/RTM that iitialized the error. Example: &TERMTYP= X-K01&SERIALNUMBER= &MACADDRESS=0C-FF-34-5A-23-1B &DATA=@@ A &ERROR=SASAMNotFoud(A0) /2013 B-Cliet PDC6

51 Pos: 6 @ 1 Maual Commuicatio XML: BPA error If a error occurs while codig the recordig data with the keyword BPA (e.g. the specified digit does ot exist), the termial applicatio requests the error page as follows: (DID)&TERMTYP=$(TERMTYP)&SERIALNUMBER=$(SERIALNUMBER) &MACADDRESS=$(MACADDRESS)&DATA=$(BPA,1) &ERROR=BPAError(<BPA>) I this process the recorded data are trasferred with the keyword DATA startig with digit 1 (=$[BPA,1]). The request cotais a additioal descriptive text (ERROR=BPAError) ad a idicatio o the BPA defiitio that iitialized the error. Example: &TERMTYP= X-K01&SERIALNUMBER= &MACADDRESS=0C-FF-34-5A-23-1B &DATA=@@ A &ERROR=BPAError(BPA,-4,10) B-Cliet PDC /

52 Pos: 7 /KABA Kapitel (SW)/PDC6 Module/Fuktiostaste, 1 Pos: 7.2 /Modul-Kapitel/Aufbau ud @ 1 Pos: 7.3 /Überschrift/2/ÜS 1 Pos: 7.4 /Modul-Kapitel/Aufbau ud @ 1 Pos: 7.5 /Software-Hadbücher/B-Cliet PDC/B-Cliet 1 Biometrie Pos: Pos: 7.7 /Modul-Kapitel/Aufbau ud @ 1 Commuicatio Maual 2.9 Fuctio keys The behavior of each fuctio key ca be defied for each idividual key via parameters i the followig maer: Static A fixed bookig procedure ca be assiged to a fuctio key. Per key, up to 18 iput steps ca be defied via so-called sigle fuctio blocks. The iputs established for a bookig are requested by the termial itself. Dyamic A fuctio key ca also be defied as a dialog key. I this case, all iputs are made i a dialog with the host (G Dialog) Press the key to start the dialog. The host will sed a request record which will be aswered each time by the termial with the iput data. The host will decide whether other requests are active ad whe the dialog ad thus the bookig is fiished Master records All the iformatio o a specific badge umber is stored i the master record. The master record cotais iformatio o the PIN umber, authorizatios, time profiles ad perso-related display texts. Master records ca be stored i the termial. This allows the termial itself to decide whether a bookig is authorized. Whether a bookig is authorized ca also be requested olie by the host. I this case, o master records are required i the termial. Master records ca be trasmitted to the termial at ay time, which will overwrite the curretly valid master record. Idividual master records ca be deleted from the host. Likewise, master records ca be requested by the host Time profiles The bookig authorizatio ca be restricted to specific times ad days. I this case, a so-called time profile will be assiged to a master record /2013 B-Cliet PDC6

53 Maual Commuicatio 2.12 Basic data record structure The >3E01 dowload record show below explais the data record structure. This data record switches the termial from stadard time to daylight savig time ad vice versa. With this data record, you ca idicate whether data records geerated by the termial will iclude secods i their time format or ot. The Example colum i the table below shows typical values used i this data record. All etries i the dowload records are ASCII characters. Abbreviatio Meaig Example GID Group DID Device address A ON/OFF/AUTO Operatig mode 0 RT Record type > RTM Record type modificatio 3 BI E BI Block idetificatio 0 BI 1 M Moth 1 M Moth Stadard time/daylight savig 0 T Day time switchover 2 T Day 9 RES Reserved Secods i data record 0 = No, 1 = Yes 0 * Further iformatio * B-Cliet PDC /

54 Pos: 8 @ 1 Commuicatio Maual Explaatio of abbreviatios The followig abbreviatios are used i the descriptios of the data records. GID, DID GID: Group address DID: Device address The group- ad device idetificatio represet the address of the device. Chapter 2.4 shows the possible group ad device addresses. ON/OFF/AUTO Determies the curret operatig status of the termial. Chapter 2.3 shows the predefied characters of the operatig status. I data records trasmitted from the computer to the termial, this digit may be filled with a blak. RT, RTM Record type ad record type modificatio. They specify the data records. Chapter 5.1 shows the possible Record type/record type modificatios. BI Block idetificatio.it specifies the type of up- or dowload records. Chapter 0 shows the possible block idetificatios. CI Clock idetificatio. The clock idetificatio idicates the curret status of the time i the termial. The table i chapter 5.4 shows the defied characters. EI Error idetificatio. If a error occurs durig the verificatio of the recordig data, this will be etered ito the data record as a error idetificatio. If several errors are detected, the error with the highest priority is etered. Chapter 5.6 shows the possible error idetificatios. YY/MM/DD Date idicatio: Year/Moth/Day. hh/mm possibly ss Time idicatio: hours/miutes ad possibly secods. After a cold start of the termial, the time idicatio cosists of hours ad miutes. To iclude secods, this optio must be set usig the dowload record >3E01, see chapter ll/cc/vv Tag (6 characters) for user laguage: laguage/coutry/variat. After a cold start of the termial, the tag is ot etered i the data record. The etry of the user laguage idetificatio must set usig a dowload record, see chapter RES Reserved: the dowload record must be filled with the specified characters /2013 B-Cliet PDC6

55 Pos: 9 /KABA Kapitel (SW)/PDC6 Module/Allgemeie 1 Maual Commuicatio 2.13 Geeral termial parameters Buffer Backup Fuctio of the parameter If the trasmitted data records eed to be saved i the termial, you ca set this optio with the buffer backup fuctio. If buffer backup is set, trasmitted data records are ot deleted. This data will still be available i the termials buffer memory. The data records stored i the buffer memory ca oly be deleted or requested agai whe usig a special data record. If buffer-backup is activated, the trasmitted data records must be deleted from the buffer from time to time. Otherwise, the buffer will evetually be full sometimes, depedig o the amout of bookigs. If the buffer is full, a bookig is rejected with the message No data trasmissio. Stadard settig after cold start Data records are deleted after trasmissio. No buffer backup. Ifo Topic 3.4 Buffer backup cotrol records Required dowload record Logical group address (GID) Fuctio of the parameter The logical group address is a part of the termial address. Values from 00 to 29 are valid for logical group addresses. A cold start does ot affect the group address. Stadard settig after cold start The logical group address is 00. Ifo Topic 2.4 Table of possible group addresses Required dowload record B-Cliet PDC /

56 Commuicatio Maual Logical device address (DID) Fuctio of the parameter The logical device address is a part of the termial address. Values from 00 to 59 are valid for logical device addresses. A cold start does ot affect the device address. Stadard settig after cold start The logical device address is 00. Ifo Topic 2.4 Table of possible device addresses Required dowload record Respose timeout Fuctio of the parameter The parameter supervises the arrivig of a logical bookig respose after the termial has trasmitted recordig data olie to the computer. The termial expects a valid respose withi the respose timeout. Durig this time the message Please wait is displayed. If o respose arrives withi this time, the termial switches to offlie operatio mode. The respose timeout i secods is four times as log as the defied value (for compatibility reasos with the Bedas series). Stadard settig after cold start The preset value is 3 secods, this meas the total time of respose timeout is 4x3 = 12 secods. Ifo Topic Required dowload record /2013 B-Cliet PDC6

57 Maual Commuicatio Dowload record Buffer backup ad logical idetificatio The parameters described i the previous chapters are modified i the termial usig the followig dowload record. For example, here are the settigs after a cold start. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio S 0 Block idetificatio 1 0 Buffer backup 0 = No; 1 = Yes 0 Reserved Reserved Reserved Logical group address (GID) Logical device address (DID) Respose time-out i 0.1 sec. steps Possible values: Example: (030x0.1 sec = 3.0 sec)... 9 digits reserved 0 0 B-Cliet PDC /

58 Commuicatio Maual Switchover from stadard time (witer) to daylight savig time Fuctio of the parameter This parameter defies, how ad at what time the switchover betwee two time periods (stadard time ad daylight savig time) takes place. The parameter cosists of three parts: the day of switchover the time of switchover the time offset with idicatio of directio. You ca choose betwee automatic switchover with fixed time rules, activated, if o poit i time is set. adjustable switchover with adjustable time rules. Adjustable switchover The termial chages betwee stadard ad dayligth savig time at the defied day ad time with the defied offset ad directio. Oce the time has bee switched, the set values are deleted. For aother switchig, the parameters have to be set agai. (summer) Automatic switchover If a date of the first half of the year is etered as the switchig day, the device automatically chages from stadard time to daylight savig time at 2:00 a.m. to 3:00 a.m. If a date of the secod half of the year is etered, the device automatically switches from daylight savig time to stadard time. This happes i the morig at 3:00 a.m. to 2:00 a.m. Oce the time has bee switched, the set values are deleted. For aother switchig, the parameters have to be set agai. Sice it caot be guarateed that the time server ad the device switch at the same time, o date/time records should be trasmitted durig that period! If the time server is located i aother time zoe (possibly oe without switchig to daylight savig time), this must be take ito accout whe trasmittig time records! Stadard settig after cold start No switchig is set. Ifo Topic 3.6 Time settig records Required dowload record /2013 B-Cliet PDC6

59 Maual Commuicatio Secods i data record Fuctio of the parameter Data records geerated by the termial ad trasmitted to the computer, cotaiig hours ad miutes as time idicatio, ca also cotai the secods. If the parameter is activated, the time idicatio is additioally provided with secods. Thus, the data records are exteded by two digits. The clock idetificatio i the data records is also modified. Stadard settig after cold start The time idicatio does ot iclude secods i the data records. Ifo Topic 5.4 Table of clock idetificatios Required dowload record User laguage i the data record Fuctio of the parameter Data records geerated by the termial ad trasmitted to the computer, ca also cotai a idetificatio for the user laguage followig the time idicatio. If the parameter is activated, the data record is additioally provided with the idetificatio. Thus, the data records are exteded by six digits. The clock idetificatio i the data record chages as well. Stadard settig after cold start The data records do ot cotai ay idetificatio for the user laguage. Ifo Topic 5.7 Table of laguage idetificatios 5.4 Table of clock idetificatios Required dowload record B-Cliet PDC /

60 Commuicatio Maual Dowload record Stadard time/daylight savig time switchig The parameters described i the previous sectios are modified i the termial usig the followig dowload record. This example shows the settigs after a cold start. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio E 0 Block idetificatio 1 M M D D 0 Reserved 0 0 h h m m Date of switchig = o switchig Secods ad user laguage; see the followig descriptio Time of switchig = automatic switchig + Directio of switchig (+ = forwards, - = backwards) 0 h 0 h 0 m 0 m Time offset of switchig i hours / miutes Secods ad user laguage Iput Set parameter 1 Secods i the data record 2 User laguage i the data record 3 Secods ad user laguage i the data record /2013 B-Cliet PDC6

61 Maual Commuicatio Display time Authorized" Fuctio of the parameter The parameter defies the display time of messages for a authorized bookig. The value is etered i 0.1 of a secod. Possible iput values: 000 to 999. This correspods to secods. Example: Iput value 050x0.1 sec = 5.0 secods Stadard settig after cold start The display time is 5.0 secods. Ifo Topic Required dowload record Display time "Not authorized" Fuctio of the parameter The parameter defies the display time of messages for ot authorized bookigs. The value is etered i 0.1 of a secod. Possible iput values: 000 to 999. This correspods to secods. Example: Iput value 050x0.1 sec = 5.0 secods Stadard settig after cold start The display time is 5.0 secods. Ifo Topic Required dowload record B-Cliet PDC /

62 Commuicatio Maual Display time Display ifo Fuctio of the parameter The parameter defies the display time for authorized bookigs with display ifo. The value is etered i 0.1 of a secod. Possible iput values: 000 to 999. This correspods to secods. Example: Iput value 120x0.1 sec = 12.0 secods Stadard settig after cold start The value for the display time "Display ifo" is 000. Thus, the iput from the parameter Display time Authorized is applied. Ifo Topic Required dowload record Pull-i time relay 1 I/O Fuctio of the parameter The parameter defies the pull-i time of door-opeer relay 1. The value is etered i 0.1 of a secod. Possible iput values: 000 to 999. This correspods to secods. Example: Iput value 030x0.1 sec = 3.0 secods Stadard settig after cold start The pull-i time of the door-opeer relay is 3.0 secods. Ifo Topic 2.20 Activate relay 1 usig the parameter record (Z1-record) Activate relay 1 usig the data record (J-record) Required dowload record /2013 B-Cliet PDC6

63 Maual Commuicatio User timeout Fuctio of the parameter The parameter defies the time durig which the termial waits for a badge iput or keyboard etry. If there is o iput made durig this time, the termial returs to its basic state. The value is etered i 0.1 of a secod. Possible iput values: 000 to 999. This correspods to secods. Example: Iput value 120x0.1 sec = 12.0 secods Stadard settig after cold start The user time-out is 12.0 secods. Ifo Topic Required dowload record B-Cliet PDC /

64 os: 44 Commuicatio Maual Dowload record "Duratios" The parameters described i the previous sectios are modified i the termial by meas of the followig dowload record, whereas the time idicatios are etered i 0.1 sec raster. This example shows the settigs after a cold start. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio X 0 Block idetificatio Display time Authorized Value: (050x0.1 sec = 5.0 sec) 0 Reserved Display time Not authorized Value: (050x0.1 sec = 5.0 sec) 0 Reserved Pull-i time of relay 1 Value: (030x0.1 sec = 3.0 sec) 0 Reserved User time-out Value: (120x0.1 sec = 12.0 sec) 0 Reserved Display time Display ifo Value: (000 = idetical to display time "Authorized") 0 Reserved /2013 B-Cliet PDC6

65 Pos: 49 /Software-Hadbücher/B-Cliet HR/Allgemeie Defiitioe/Dowloadsatz 3 Maual Commuicatio PIN for biometrics maagemet This fuctio is curretly ot implemeted. Fuctio of the parameter The access to the biometrics maagemet i a termial equipped with a CBM reader module ca be secured by defiig a PIN. The PIN for the biometrics maagemet must be etered after the C-4-9 sequece ad must be cofirmed with the Eter key. If o PIN for the biometrics maagemet is defied, just press the Eter key after the C-4-9 sequece. The PIN for the biometrics maagemet must be etered always i 4 digits. Stadard settig after cold start No PIN defied for biometrics maagemet. Dowload record GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio X 0 Block idetificatio digits PIN for biometrics maagemet Valid etries: 0000 to 9999 = o PIN (default) 4 digits reserved 8 digits reserved 8 digits reserved B-Cliet PDC /

66 Pos: 10 @ 1 Commuicatio Maual Character set idetificatio For compatibility reasos cocerig the Bedas series, the character set idetificatio ca be set as i the past (trasmissio of 7-bit characters). The character coversio i multiligual mode is doe with the parameters i the [Laguages] sectio i the b-cliet_pdcx.ii file. Fuctio of the parameter The termial ca operate with differet character sets. The character set idetificatio defies which oe is to be used. The table of character sets shows the characters that ca be displayed Stadard settig after cold start: The characterset 000 (USA ASCII) is preset. Ifo Topic 5.13 Table of character sets ad character set idetificatios. 6.5 [Laguages] sectio i the b-cliet_pdc6.ii file. Dowload record GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio X 0 Block idetificatio 7 0 Reserved Character set idetificatio /2013 B-Cliet PDC6

67 Pos: 11 /KABA Kapitel (SW)/PDC6 1 v Maual Commuicatio 2.14 Fuctio key parameters The parameters i the fuctio key parameters group determie the behavior of each sigle fuctio key Acoustic sigal This parameter exists oce oly i the applicatio ad is therefore valid for all fuctio keys. Fuctio of the parameter The parameter determies, if acoustic sigals occur i case of errors or ot authorized bookigs. Stadard settig after cold start No acoustic sigal. Ifo Topic Required dowload record Fuctio key as iput filter Fuctio of the parameter Fuctio key is defied as a iput filter Each iput is checked accordig to the defied check criteria. Erroeous iputs are rejected by the termial with a error message. The iput must be repeated. The bookig ca oly be cotiued after a correct iput. Fuctio key is ot defied as a iput filter Each iput is checked accordig to the defied check criteria. However, erroeous iputs are ot rejected by the termial. The bookig ca be cotiued i ay case. The check result is etered ito the recordig data record as a error idetificatio, see chapter 5.6. Because oly oe error idetificatio ca be etered, oly the first oticed error ca be cosidered. The recordig data record is trasmitted to the host computer immediately The host computer respods with a logical bookig aswer to determie whether the bookig is authorized or ot. If the bookig aswer is positive, the relay Authorized is activated. If the termial does ot receive a logical bookig respose from the computer, it chages to offlie mode ad decides itself if the bookig is authorized or ot. If the bookig result is positive, the relay Authorized is activated. The recordig data record will ot be trasmitted to the computer but treateed as defied i the Buffer Authorized Recordig Data / Buffer Not Authorized Recordig Data parameters, see chapter et sqq. B-Cliet PDC /

68 Commuicatio Maual Stadard settig after cold start All fuctio keys are defied as iput filters. Ifo Topic 5.6 Table of error idetificatios 3.5 Logical bookig respose Buffer backup Required dowload record Termial awaits logical bookig respose i offlie ad autoomous mode Fuctio of the parameter This parameter defies if the termial awaits a logical bookig respose from the computer also i offlie or autoomous operatig mode. If the termial does ot recieve a logical bookig respose, the iteral bookig respose will be displayed. i Stadard settig after cold start The termial does ot await a logical bookig respose from the computer i offlie or autoomous operatig mode. Ifo Topic Required dowload record /2013 B-Cliet PDC6

69 Maual Commuicatio Key repeat fuctio Fuctio of the parameter Before bookig, the desired fuctio key must be operated. After the bookig the termial returs to its previous state. If a further bookig is to be carried out with the same fuctio key, this fuctio key must be pressed agai. Fuctio keys with parameter Key Repeat Fuctio allow to book without pressig that key agai. If o data is etered, the termial returs to its basic state after expiratio of the operatio timeout. Stadard settig after cold start No repeat fuctio is activated. Ifo Topic Required dowload record Idividual master record required Fuctio of the parameter The parameter defies, that a idividual master record must be stored i the termial for each ID o. read from a badge. If a fuctio key is ot defied as iput filter ad the parameter "Idiviual master records required" is set, but o idividual master record exits for the ID o. read from a badge, the error idetificatio D No master record foud is etered ito the iput record. If a fuctio key is defied as iput filter ad the parameter "Idiviual master records required" is set, but o idividual master record exits for the ID o. read from a badge, the iput is rejected with the error message "Kei Stammsatz" ("No master record"). Stadard settig after cold start No idividual master record is required after a cold start. Ifo Topic 5.6 Table of error idetificatios Required dowload record B-Cliet PDC /

70 Commuicatio Maual Activate Authorized relay I/O Fuctio of the parameter The parameter defies if the Authorized relay (relay 1) is activated after a authorized bookig. Stadard settig after cold start The Authorized relay is activated after a authorized bookig. Ifo Topic Required dowload record Bookigs allowed i offlie / autoomous mode Fuctio of the parameter The parameter defies if bookigs are allowed i offlie or autoomous operatig mode. Stadard settig after cold start Bookigs are allowed i offlie or autoomous operatig mode. Ifo Topic Required dowload record Buffer recordig data This parameter is maily importat i the offlie ad autoomous operatig mode. If the parameter Buffer backup is set, it is also valid for the olie operatig mode. Fuctio of the parameter The parameter defies, if recordig data is buffered. If the buffer is activated, both authorized ad ot authorized record data are buffered. Stadard settig after cold start Recordig data is buffered. Ifo Topic Required dowload record /2013 B-Cliet PDC6

71 Maual Commuicatio Show persoal text This parameter is oly importat with a positive aswer ( Thak You ) if a master record has bee foud ad o mailboxtext is show. Fuctio of the parameter This parameter defies if the persoal text which is defied i the master record is displayed. Stadard settig after cold start No persoal text is show for ay fuctio key. Ifo Topic Required dowload record Suppress display ifo i master record Fuctio of the parameter The parameter defies if the display ifo i the master record is suppressed If the parameter is set, the display ifo is ot displayed durig a bookig. Stadard settig after cold start The display ifo from the master record is ot suppressed for ay fuctio key. That meas, it is show i the display. Ifo Topic Required dowload record B-Cliet PDC /

72 Commuicatio Maual Fuctio key as dialog key If a fuctio key is defied as a dialog key, all other parameters defied for this fuctio key (i.e. are ot relevat). Fuctio of the parameter The parameter defies a fuctio key as a dialog key. If a fuctio key is defied as dialog key ad the dialog is ot blocked,, the termial trasmits a G8 record after operatig a fuctio key ad awaits a G0 record. If o G0 record is replied to the termial, it will exit the dialog with the message Kei Dialog möglich (dialog impossible) after the respose time-out expires. The dialog mode ca also be termiated cosciously by trasmittig a G9 record to the termial istead of the expected G0 record. The employee ca exit the dialog easily by pressig oce agai the fuctio key that started the dialog. Stadard settig after cold start No fuctio key is set as dialog key. Ifo Topic Block/release the dialog G0 record G9 record Required dowload record Cotet of the G8-record This parameter is oly importat if the fuctio key is set as dialog key. Fuctio of the parameter The parameter defies the cotet of the G8-record. Stadard settig after cold start The cotet of the G8-record is the RT/RTM (record type/record type modificatio) of the operated fuctio key. Ifo Topic Fuctio key as dialog key G8 record Required dowload record /2013 B-Cliet PDC6

73 Maual Commuicatio Check o time authorizatio This parameter is importat if the employee s master record refers to a time profile. Fuctio of the parameter The parameter determies, whether the Time authorizatio parameter i the time profile will be cosidered. Stadard settig after cold start For all fuctio keys, the Check o time authorizatio parameter is ot cosidered i the time profile. Ifo Topic Check o time authorizatio/idetificatio bytes Required dowload record Number of display ifo This parameter is oly importat if display ifo from master records is displayed. Fuctio of the parameter This parameter determies, whether up to 4 or up to 10 display ifo should be displayed. Stadard settig after cold start For all fuctio keys 4 display ifos are show. Ifo Topic Required dowload record B-Cliet PDC /

74 Commuicatio Maual Dowload record Fuctio key parameters The parameters described i the previous chapters are modified i the termial usig the followig dowload record. Dowload record P01 for the fuctio keys F1 to F15. GID DID ON/OFF Group address Device address Betriebszustad > Record type 3 Record type modificatio P 0 Block idetificatio for the 1 fuctio keys F1 F digits reserved Acoustic sigal 0 = No, 1 = Yes 0. 4 digits reserved F.. F F Key parameters for fuctio key F1, see followig descriptio Key parameters for fuctio keys F2 to F15, 2 digits each, (28 digits i total) Reserved F digits reserved F F Dialog parameters for fuctio key F1, see followig descriptio Dialog parameters for fuctio keys F2 to F15, 2 digits each, (28 digits i total) Reserved F /2013 B-Cliet PDC6

75 Maual Commuicatio Key parameters for fuctio keys F1 F15 The termial iterprets the characters etered i the dowload record as a hex code which cotais several parameters. 1. byte Hex valecy Bit Fuctio key as iput filter 0 = No 1 = Yes Termial awaits logical bookig respose i offlie ud autoomous operatig mode 0 = No 1 = Yes Key repeat fuctio 0 = Yes 1 = No Idividual master record required 0 = No 1 = Yes 2. byte Hex valecy Bit Activate Authorized relay 0 = No 1 = Yes Reserved 0 Bookig allowed i offlie mode 0 = No 1 = Yes Buffer recordig data 0 = No 1 = Yes Ifo Topic Hexadecimal codig B-Cliet PDC /

76 Pos: 12 @ 1 Commuicatio Maual Dialog parameters for fuctio keys F1 F15 The termial iterprets the characters etered i the dowload record as a hex code which cotais several parameters. 1. byte Hex valecy Bit Reserved Reserved Show persoal text 0 = No 1 = Yes Suppress display ifo i master record 0 = No 1 = Yes 2. byte Hex valecy Bit Fuctio key as dialog key 0 = No 1 = Yes Cotet of the G8 record 0 = RT/RTM of the operated key 1 = G8 Check o time authorizatio 0 = No 1 = Yes Number of display ifo 0 = 4 display ifo 1 = 10 display ifo Ifo Topic Hexadecimal codig /2013 B-Cliet PDC6

77 Pos: 13 /KABA Kapitel (SW)/PDC6 1 Maual Commuicatio 2.15 Fuctio key fuctios The parameters of the Fuctio key fuctios group defie the bookig procedure for a fuctio key. Predefied bookig procedures exist for some fuctio keys. All settigs are modifiable at ay time. Up to 18 sigle fuctio blocks ca be defied for each fuctio key. The last block most be a locked block, if less the 18 sigle steps are required. Ifo Topic Stadard settig after cold start Record type/record type modificatio Fuctio of the parameter The parameters defie the record type ad record type modificatio used to trasmit a data record to the computer. All RT/RTM show i the table i chapter 5.2 sectio recordig data ca be defied. The record type modificatios # (23hex) ad $ (24hex) are a special feature. They are used for the automatic recogitio of the bookig directio (I or Out) i coectio with a record type defiitio. Fuctioig of the automatic recogitio of the bookig directio The B-eco termial is equipped with 2 proximity sesors (o the right ad left of the RFID readers, ot visible). If the feature automatic recogitio of the bookig directio is used, the gesture shall be stopped at the RFID symbol. S I Out S If a record type is parameterized with the record type modificatio #, the followig applies: If the left sesor is activated before geeratig badge data, a I bookig will be detected. The RT/RTM that is defied for the F01 fuctio key is etered i the data record. If the right sesor is activated before geeratig badge data, a Out bookig will be detected. The RT/RTM that is defied i the F02 fuctio key is etered i the data record. B-Cliet PDC /

78 Commuicatio Maual If the record type is parameterized with the record type modificatio $, the followig applies: S Out I S If the right sesor is activated before geeratig badge data, a I bookig will be detected. The RT/RTM that is defied for the F01 fuctio key is etered i the data record. If the right sesor is activated before geeratig badge data, a Out bookig will be detected. The RT/RTM that is defied i the F02 fuctio key is etered i the data record. This fuctio should ot be assiged to the F01 ad the F02 fuctio keys, due to the fact that the record type modificatio of these keys is also etered i the data record. By default, the automatic recogitio of the bookig directio is ot assiged to ay fuctio key. Stadard settig after cold start Fuctio key F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 Record type/record type modificatio B1 B2 B3 B0 F0 FE FH FF ot used ot used FN FK FM ot used ot used Ifo Topic Required dowload record /2013 B-Cliet PDC6

79 Maual Commuicatio Display data of the iput uit Fuctio of the parameter The parameter defies, if the data of the iput uit is displayed i the correspodig sigle fuctio block. Stadard settig after cold start The data of the iput uit is ot displayed. Ifo Topic Iput uits Required dowload record Iput uits Fuctio of the parameter The parameter defies the iput uit for the correspodig sigle fuctio block. Iput uit Keyboard Reader 1 or Reader 2 List Date/Time Fix text Descriptio If this iput uit is defied, a keyboard etry must be made. If this iput uit is defied, a badge must be etered at reader 1 or reader2. The reader parameters are stored i the EEPROM ad ca be set up with the service module. If this iput uit is defied, a etry from a list must be selected. The parameter From digit (01 to 20) is used to select the list umber. The etry 00 meas, o list is selected. If this iput uit is defied, date ad time are etered ito the recordig data record without user activity. The format is YY/MM/DD/hh/mm/ss (up to 12 characters). If this iput uit is defied, a stored fix text is etered ito the recordig data record without user activity. Additioally, the parameters Number of digits, From digit ad Fix texts must be observed. B-Cliet PDC /

80 Commuicatio Maual Iput uit Duplicatio field Descriptio If this iput uit is defied, a duplicatio field is accessed without user activity. A duplicatio field is a temporary storage allowig to store, read ad delete data. The termial ca maage 8 duplicatio fields. Each duplicatio field cosists of 20 digits ad is distiguished by its duplicatio field umber 0 to 7. Data which is stored i the duplicatio field is safe util ew data is stored or util the duplicatio field is deleted. Storig data i a duplicatio field The recordig data of the previous sigle fuctio block is stored i a duplicatio field. Therefore, 00 must be etered for the parameter Number of Digits. The parameter From digit (01 to 20) defies the digit the duplicatio field is overwritte from. The limit value o. parameter defies umber of the duplicatio field. Readig data from a duplicatio field The data of a duplicatio field is etered i the recordig data record. The parameter Number of digits (01 to 20) defies, how may digits are etered ito the recordig data record. The parameter From digit (01 to 20) defies the digit from which the data is etered i the recordig data record. The Limit value o. parameter defies umber of the duplicatio field. Deletig data i a duplicatio field Data i duplicatio fields are deleted by overwritig it with blaks (20 hex ). For this purpose 00 must be etered for the parameter Number of digits ad From digit. The Limit value o. parameter defies umber of the duplicatio field. Ifo Topic 2.18 Lists / Number of digits/from digit Fix text 2.17 Duplicatio field Stadard settig after cold start Required dowload record /2013 B-Cliet PDC6

81 Maual Commuicatio Recordig data umeric/alphaumeric Fuctio of the parameter The parameter defies whether umeric or alphaumeric iputs are allowed for the correspodig sigle fuctio block. Ifo Topic Stadard settig after cold start Required dowload record Keyboard iput rollig/fix Fuctio of the parameter This parameter is oly importat, if a keyboard iput is set. Rollig The etered key characters are shifted through the display from the right to the left. With this type of etry, as may digits as defied with the Number of digits parameter may be etered. If less digits are etered, leadig zeros (30 hex ) are etered if umeric iput is defied or leadig blaks (20 hex ) are etered if alphaumeric iput is defied. Fix The digits reserved for the keyboard iput are displayed as hyphes. The cursor is o the very left positio With each digit etered, the cursor moves oe digit to the right. If umeric iput is defied, as may digits as defied via the parameter Number of Digits must be etered. If less digits are etered, the bookig is rejected with a error message. If alphaumeric iput is defied, as may digits as defied via the parameter Number of digits ca be etered. If less digits are etered, the displayed hyphes are etered ito the recordig data record. Ifo Topic Iput uits Recordig data umeric/alphaumeric Stadard settig after cold start Required dowload record B-Cliet PDC /

82 Commuicatio Maual Keyboard allowed Fuctio of the parameter With this parameter, the keyboard ca be allowed additioally to the defied iput uit. If the Display data of iput uit parameter is set additioally, data ca be modified with the keyboard after receivig it from ay iput uit. Ifo Topic Display data of the iput uit Iput uits Stadard settig after cold start Required dowload record Check for iput legth Fuctio of the parameter The parameter is used to activate the check for iput legth for the correspodig sigle fuctio block. If the check is activated, the legth of the read bookig data is checked immediately agaist the defiitios made with the parameters From digit ad Number of digits. If the check fails due to deviatio of the read bookig data, a Iput Error alert requests for reeterig the data. Stadard settig after cold start The check for iput legth is deactivated for all sigle fuctio block after a cold restart. Ifo Topic Required dowload record /2013 B-Cliet PDC6

83 Maual Commuicatio Number of digits Fuctio of the parameter The parameter defies the iput for the correspodig sigle fuctio block ad the umbers of digits to be etered. A maximum of 42 digits ca be set. The settig 00 switches the iput off. Additioally, this parameter defies how may digits are etered ito the recordig data record. If the iput uit delivers more data the defied here - regardig the From digit parameter -, the redudat data is cut off o the right had side. If the iput uit delivers less data the defied here, it is filled up accordig to the iput type defiitio. Ifo Topic Keyboard iput rollig/fix From digit Stadard settig after cold start Required dowload record B-Cliet PDC /

84 Commuicatio Maual From digit Fuctio of the parameter The parameter defies for the correspodig sigle fuctio block, from which digit o the iput data is etered ito the recordig data record. If the iput data is to be etered ito the recordig data record from the first digit o, the parameter must be set to from digit 00. If the cotet of the badge is to be eteredito the recordig data record from the first digit o, the parameter must be set to from digit 01. If the iput uit "Fix text" is defied, the "From digit" parameter defies, from which digit o the fix text is etered ito the recordig data record. If the iput uit List is defied, the From digit parameter defies the list that is to be actived. Fix-text o From digit to to to to to 99 Ifo Topic Stadard settig after cold start Required dowload record Text o. Fuctio of the parameter The parameter defies a text for the correspodig sigle fuctio block which is the displayed i the iput mask. There are 25 dialog texts available. These dialog texts ca be modified via dowload. The etry 00 meas, o text to be displayed. Ifo Topic Dialog texts Stadard settig after cold start Required dowload record /2013 B-Cliet PDC6

85 Maual Commuicatio Default settigs of the fuctios keys The followig table shows the default parameters of the fuctio keys after a cold start. For a better overview, the parameters are provided with abbreviatios. The meaig of the abbreviatios is give by uderliig the accordig characters i the head lie. Fuctio key Sigle fuctio block Iput uit Reader 1/2, Keyboard, List, Fix text Iput format Numeric / Alphaumeric Keyboard iput Rollig / Fix Keyboard allowed Yes/No Number of digits From digit Text o. F1 F5 F6 F7 1. R1 Al R N R1 Al R N R2 Nu F Y R2 Nu F Y Kb Nu F Y Fi Al R N R1 Al R N R2 Nu F Y R2 Nu F Y Kb Nu F Y Kb Nu R Y Li Nu R N B-Cliet PDC /

86 Commuicatio Maual Fuctio key Sigle fuctio block Iput uit Reader 1/2, Keyboard, List, Fix text Iput format Numeric / Alphaumeric Keyboard iput Rollig / Fix Keyboard allowed Yes/No Number of digits From digit Text o. F8 1. R1 Al R N R2 Nu F Y R2 Nu F Y Kb Nu F Y Kb Nu R Y Kb Nu F Y F11, 1. R1 Al R N F12, F13 2. R2 Nu F Y F9, F10, F14, F15 Block blocked /2013 B-Cliet PDC6

87 Maual Commuicatio Limit value o. Fuctio of the parameter This parameter defies for each sigle fuctio block the iterpretatio of the iput data ad the checks to be carry out. The followig limit value umbers are preset: Limit value umber Check/meaig 00 No Check Limit value pair 01. Limit value pair No Check 17 No Check 18 No Check 19 Versio o. check 20 ID o check 21 PIN check 22 No Check 23 No Check 24 No Check 25 No Check Limit value o. 00, 16 to 18, 22 to 25; o check: The etered data will ot be checked. Limit value o. 01 to 15; Limit value pair 01 to 15: The iput data is compared with the correspodig limit value pair. If a fuctio key is ot defied as iput filter ad the data does ot match the limit value pair, the correspodig error idetificatio is etered ito the recordig data record. The error idetificatio 1 Data outside limit value pair 1 up to error idetificatio 15 Data outside limit value pair 15 ca be etered ito the recordig data record. If a fuctio key is defied as iput filter ad the data does ot match the limit value pair, the iput is rejected with the message: "Fehler: Grezwert ( Error: Limit value"). Ifo Topic 2.16 Limit value pairs 5.6 Table of error idetificatios B-Cliet PDC /

88 Commuicatio Maual Limit value o. 19; Versio umber This check ca be carried out oly if a sigle fuctio block with the limit value o. 20 (ID-o.) is pre-defied. The etered data is compared with the versio o. i the idividual master record. If a fuctio key is ot defied as iput filter ad the versio o. is ot idetical, the error idetificatio C "Versio o. false" is etered ito the recordig data record. If a fuctio key is defied as iput filter ad the versio o. is ot idetical, the iput is rejected with the error massage "Versios-Nr. falsch" (Versio o. false). Limit value o. 20: ID o.: The data read from the badge is iterpreted as ID umber. It is used to access a idividual master record. If LEGIC advat readers are i use, please observe the followig: The followig restrictios must be observed for LEGIC advat readers which are ot customized: Specificatio of the versio umber - oly 1 digit Specificatio of the ID umber - oly 7 digits. The correspodig driver is selected i the system mode of the termial. Limit value o. 21; PIN check This check ca be carried out oly if a sigle fuctio block with the limit value o. 20 (ID-o.) is pre-defied. The keyboard data that has bee etered is compared with the PIN (persoal idetificatio umber) stored i the master record. If a fuctio key is ot defied as iput filter ad the PIN is ot idetical, the error idetificatio E "PIN wrog or missig" is etered ito the recordig data record. If a fuctio key is defied as iput filter ad the PIN is ot idetical, the iput is rejected with the error massage "Code-Nummer falsch" (Code umber false). Stadard settig after cold start The iput data is ot checked (limit value o 00). Ifo Topic 5.6 Table of error idetificatios 3.7 Master records Required dowload record /2013 B-Cliet PDC6

89 Maual Commuicatio Release iput uit Fuctio of the parameter The parameter releases the iput uit, e.g. a LEGIC reader. A iput uit must be released to use it agai i a followig sigle fuctio block. If ot released, the data of this sigle fuctio block is used agai if the same uit is defied i a followig block. Stadard settig after cold start The iput uit is ot released. Ifo Topic Required dowload record Eter recordig data ito data record Fuctio of the parameter The parameter defies for the correspodig sigle fuctio block, if the etered data is etered ito the recordig data record. Stadard settig after cold start The iput data is etered ito the recordig data record. Ifo Topic Required dowload record Use sigle fuctio block Fuctio of the parameter The parameter defies if a sigle fuctio block is used durig bookig or ot. If the parameter Key Repeat Fuctio is set, it ca be defied, if the sigle fuctio block is used with the first bookig oly or from the secod bookig o. Stadard settig after cold start A sigle fuctio block is used durig the bookig process. Ifo Topic Required dowload record B-Cliet PDC /

90 Commuicatio Maual Positive acustic cofirmatio after reader iput Fuctio of the parameter The parameter defies for the accordig sigle fuctio block, if a acoustic sigal is geerated after a reader iput. Stadard settig after cold start No acoustic sigal is geerated. Ifo Topic Required dowload record Covered iput Fuctio of the parameter The parameter defies for the correspodig sigle fuctio block if data iput is displayed or ot. If the Covered Iput parameter is set, the etered data is ot show o the display. Istead, the character * appears as dummy for every digit etered. Stadard settig after cold start The iput data is displayed. Ifo Topic Required dowload record /2013 B-Cliet PDC6

91 Maual Commuicatio Dowload record sigle fuctio blocks The parameters described i the previous chapters are modified i the termial usig the followig dowload record. Highlighted i gray: 1 st sigle fuctio block. GID DID ON/OFF Group address Device address Opaertig mode > Record type 3 Record type modificatio F B F F Block idetificatio F01 to F15 See followig descriptio Record type modificatio (B1) Reserved 00 FFFF = Fuctio key blocked Device byte; FF = Block blocked Number of digits From digit Text o. 00 = Do ot display text Limit value o. Cotrol byte Max. 17 more sigle fuctio blocks possible Ed of sigle fuctio blocks B-Cliet PDC /

92 Commuicatio Maual Block idetifcatio The block idetificatio defies the fuctio key the parameters are valid for. Etry Meaig F01 Fuctio key F1... F15 Fuctio key F15 Record type/record type modificatio For the record type ad the record type modificatio, ay two ASCII characters ca be used. The followig two characters are set to 00. If the futio key shall ot be used, the four characters must be set to FFFF. Device byte The termial iterprets the characters etered i the dowload record as a hex code which cotais several parameters. If the device byte is set to FF, this block is locked ad followig blocks will be uused. 1. byte Hex valecy Bit Iput uit 000 Keyboard 001 Reader Reserved 011 Reader List 101 Duplicatio field 110 Date/time 111 Fix text Display data of iput uit 0 = No 1 = Yes /2013 B-Cliet PDC6

93 Maual Commuicatio 2. byte Hex valecy Bit Recordig data umeric alphaumeric 0 = umeric 1 = alphaumeric Keyboard iput rollig/fix 0 = rollig 1 = fix Keyboard allowed 0 = No 1 = Yes Check for iput legth 0 = No 1 = Yes Ifo Topic Hexadecimal codig B-Cliet PDC /

94 Pos: 14 @ 1 Commuicatio Maual Cotrol byte The termial iterprets the characters etered i the dowload record as a hex code which cotais several parameters. 1. byte Hex valecy Bit Release iput uit 0 = No 1 = Yes Reserved 0 Reserved 0 Eter recordig data ito data record 0 = Yes 1 = No 2. byte Hex valecy Bit Use sigle fuctio block 00 Yes 10 With first bookig oly (if key repeats) 01 With secod bookig (if key repeats) 11 No Positive acoustic cofirmatio after reader iput 0 = No 1 = Yes Covered iput 0 = No 1 = Yes Ifo Topic Hexadecimal codig /2013 B-Cliet PDC6

95 Pos: 15 /KABA Kapitel (SW)/PDC6 1 Pos: 16 @ 1 Maual Commuicatio 2.16 Limit value pairs Fuctio of the parameter The parameters of the "Limit value pairs" group are oly importat if a limit value o. 01 to 15 is stated i a sigle fuctio block, see chapter I this case, etries will be checked whether they are withi the miimum/maximum value rage which is defied with the give limit value pair. If less digits are used for the miimum/maximum value defiitio tha the desigated 8 digits, leadig zeros must be etered. Up to 15 limit value pairs may be defied ad stored i the termial. A limit value pair cosists of Block idetificatio icludig the umber of the limit value pair Miimum value- ad Maximum value. Stadard settig after cold start Miimum value: Maximum value: GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio G Block idetificatio G01 to G15; see followig descriptio 8 digits miimum value of the limit value pair digits maximum value of the limit value pair Block idetificatio The block idetificatio idetifies the limit value pair. Block idetificatio G01... G15 Meaig Limit value pair Limit value pair 15 B-Cliet PDC /

96 Pos: 17 /KABA Kapitel (SW)/PDC6 1 Pos: 22 @ 1 Pos: 18 @ 1 Commuicatio Maual 2.17 Duplicatio fields Fuctio of the parameter This parameter allows to store data i a duplicatio field. A duplicatio field is a temporary storage accessible via a sigle fuctio block. The termial ca maage 8 duplicatio fields with 20 digits max. each. The duplicatio field o. (0-7) distiguishes the duplicatio fields. Data which is stored i the duplicatio field is safe util ew data is stored or util the duplicatio field is deleted. Stadard settig after cold start All duplicatio fields cotai blaks (20 hex ). GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificato Y Block idetificatio Y10 to Y17; see followig descriptio Cotet of a duplicatio field 20 ASCII characters max. Block idetificatio The block idetificatio defies the duplicatio field where the cotet has to be stored i. Block idetificatio Meaig Y10 Duplicatio field 0 Y11 Duplicatio field 1 Y12 Duplicatio field 2 Y13 Duplicatio field 3 Y14 Duplicatio field 4 Y15 Duplicatio field 5 Y16 Duplicatio field 6 Y17 Duplicatio field /2013 B-Cliet PDC6

97 Pos: 19 /KABA Kapitel (SW)/PDC6 1 Maual Commuicatio 2.18 Lists Lists are importat if the parameter settig of a fuctio key fuctio refers to a list umber. With ay bookig accordig to the fuctio key fuctios, the termial checks whether a keyboard iput is set. I this case, the termial checks i a secod step whether a list o. is defied. If a list umber is defied i the fuctio key fuctios ad the list does exist, it will be displayed to the employee List o. Fuctio of the parameter The list umber defies a list. The list umber is eccessary to fid a defied list durig the parameter settig of the fuctio key fuctios. Up to max. 20 list (01 to 20) may be created Stadard settig after cold start No lists are defied. Ifo Topic Required dowload record Idex i list Fuctio of the parameter A list may cotai up to 30 etries (00 to 29). The idex represets the successio withi the list. It is madatory to begi the etry umberig with 00 ad cotiue i cosecutive umberig. The list will be eded with the first iterruptio. The etry meas this idex is ot used. Stadard settig after cold start The etry is stored. Ifo Topic Required dowload record B-Cliet PDC /

98 Commuicatio Maual List text o. Fuctio of the parameter The list text umbers (00 to 99) are used to defie the text that will be displayed to the bookig employee. Stadard settig after cold start List text o. 00 is stored. Ifo Topic List texts Required dowload record Data field Fuctio of the parameter The cotet of a data field is etered ito the recordig data record. Ay characters may be etered ito the 24 digit data field. The Number of digits with keyboard iput parameter defies, how may digits of the data field will be etered ito the recordig data record. Stadard settig after cold start The character is etered i the data fields. Ifo Topic Required dowload record /2013 B-Cliet PDC6

99 os: 24 @ 1 Pos: 20 @ 1 Maual Commuicatio Dowload record lists The parameters described i the previous chapters are modified i the termial usig the followig dowload record. Each dowload record may cotai up to 8 blocks. This meas, for e.g. 30 etries withi oe list, four dowload records are required. The W01 to W20 block idetificatios are oly for coutig purposes. Highlighted i gray: block 0 GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio W Block idetificatio W01 to W20 List o. (01 to 20) 00 = o list Idex i list (00 to 29) etry ot used Text o. (00 to 99) Data field 24 digits (etry i the recordig data record)... Up to 7 further blocks B-Cliet PDC /

100 Pos: 21 /KABA Kapitel (SW)/PDC6 1 Commuicatio Maual 2.19 Fuctio key cotrol The parameters of the "Fuctio Key Cotrol" group defie the time a fuctio key is automatically active from. All other fuctio keys ca also be operated furthermore. For the fuctio key cotrol, up to 12 blocks ca be stored i the termial. Each block cosists of the parameters Fuctio key switchover ad Fuctio key o Fuctio key switchover Fuctio of the parameter The parameter defies the time a fuctio key is activated from. switchover cotrol Stadard settig after cold start No activatio time is stored. Ifo Topic Required dowload record Fuctio key o. Fuctio of the parameter The parameter defies which fuctio is to be activated. umber Stadard settig after cold start No fuctio key is active. Ifo Topic Required dowload record /2013 B-Cliet PDC6

101 Pos: 22 @ 1 Maual Commuicatio Dowload record fuctio key cotrol The parameters described i the previous chapters are modified i the termial usig the followig dowload record. Highligthed i gray: block 0 GID DID ON/OFF Group address Device address Opratig mode > Record type 3 Record type modificatio Z 0 1 Hour Hour Miute Miute Block idetificatio Fuctio key switchover = o switchover Fuctio key o., see followig table... Up to 11 further blocks Fuctio key o. Etry Meaig No fuctio key 00 No fuctio key 01 Fuctio key F1 02 Fuctio key F2 03 Fuctio key F Fuctio key F15 B-Cliet PDC /

102 Pos: 23 /KABA Kapitel (SW)/PDC6 1 Commuicatio Maual 2.20 Relay cotrol The parameters of the relay cotrol group defie the active time of relay 1 away from its ormal use as a door opeer relay after a bookig. The parameters defie activatio activatio time duratio of the activatio. Up to 60 time pairs ca be defied Switch-o time relay I/O Fuctio of the parameter The parameter defies the time a relay is activated. Stadard settig after cold start No activatio time is stored. Ifo Topic Required dowload record Relay o. I/O Fuctio of the parameter The parameter defies the relay to be activated. Stadard settig after cold start Relay R1 is defied. Ifo Topic Required dowload record Operatio time I/O Fuctio of the parameter The parameter defies the operatio time for the activated relay. Stadard settig after cold start No operatio time is preset. Ifo Topic Required dowload record /2013 B-Cliet PDC6

103 Pos: 24 @ 1 Maual Commuicatio Dowload record relay cotrol The parameters described i the previous chapters are modified i the termial usig the followig dowload record. Highlighted i gray: block 0. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio Z 1 Block idetificatio Z11 to Z13 Hour Hour Miute Activatio time = o activatio Miute 0 0 Relay o. Oly 00 for relay 1 permitted 0 Pull-i time secods 0 (value x 0.1 sec) 0 Reserved 0.. Up to 19 further blocks Block idetificatio By idicatig the block idetificatio with 20 possible blocks each, up to 60 differet times ca be realized with miute precisio. Block idetificatio Meaig Z11 Block 1 to 20 Z12 Block 21 to 40 Z13 Block 41 to 60 B-Cliet PDC /

104 Pos: 25 /KABA Kapitel (SW)/PDC6 1 Commuicatio Maual 2.21 Time profiles To effect checks accordig to time profiles durig the bookig procedure, the master record must refer to a time profile. To do so, the profile ame must be defied i the master record. A maximum of up to 239 time profiles ca be stored i the termial. A time profile may cotai up to seve time pairs. A time pair always cosists of the parameters time zoe validity days idetificatio bytes. Ifo Topic 3.7 Master record defiitios Profile ame Fuctio of the parameter The profile ame idetifies a time profile deposited i the termial. Allowed profile ames are 01 hex to FE hex. The etry 00 as a profile ame meas: o valid time profile is stored for this employee a check for time authorizatio causes a egative check result. Irrespective of this etry, a check for time authorizatio always takes place if it is set i the "Fuctio key fuctios". Stadart settig after cold start No time profiles are saved i the termial. Ifo Topic Idividual master record Check for time authorizatio Required dowload record /2013 B-Cliet PDC6

105 Maual Commuicatio Time zoe Fuctio of the parameter A time pair is always valid for a certai time zoe, for example 8 a.m. to 5 p.m., ad i particular util the set miute elapses. The time zoe 8 a.m. to 5 p.m. eds at 5:59 p.m. This must be observed whe defiig time zoes. If the time zoe eeds to be defied, for example to ed at 5 p.m., the ed time must be etered at "4:59 p.m". The required time zoe is defied by specificatio of hours/miutes for "Start" ad hours/miutes for "Ed". For all udefied time zoes, there is o time authorizatio. If o time authorizatio is give, Error idetificatio N "No time authorizatio (profile)" is etered ito the data record. I the operatig modes Offlie/Autoomous the bookig is rejected with the message "No time authorizatio". Possible values: 00:00 to 11:59 p.m. The etry 24:00 is ot permitted. If a time zoe is to be active for several days (e.g. from 10:00 p.m. util 08:00 a.m.), two time pairs must be defied. Example: 10:00 p.m. to 11:59 p.m. for oe day ad 00:00 to 8:00 a.m. for the ext day. The times must ot overlap. If a time zoe eds, for example at 5:00 p.m., the ext oe ca start at 5:01 p.m. at the earliest ad ot at 5:00 p.m. Stadart settig after cold start No time zoes are are available. Ifo Topic Required dowload record Validity days Fuctio of the parameter The parameter specifies the weekdays for which the defied time pair must be valid. For a bookig, all time pairs are checked util the time zoe ad date match the curret time ad date. Stadart settig after cold start No validity days are available. Ifo Topic Required dowload record B-Cliet PDC /

106 Commuicatio Maual Idetificatio bytes Fuctio of the parameter The idetificatio bytes cotai the followig parameters: Special day idetificatio Time authorizatio PIN check Special day idetificatio The special day idetificatio assigs the time pair to a special day. If the curret day of a bookig is idetified as a special day, the time pairs are oly checked for the special day idetificatio. The check for validity days is skipped. Ifo All time pairs are checked util time zoe ad special day idetificatio match the curret time ad day. The defiitio of the special days ad special day idetificatios is performed i the special day table. Topic 2.22 Special day table Time authorizatio This parameter is oly relevat if the parameter "Check for time authorizatio" is set. This parameter is used to assig the time authorizatio for the defied time zoe. If o time authorizatio has bee assiged, error idetificatio 9 "No time authorizatio (profile) is etered ito the data record. Ifo I the operatig modes Offlie/Autoomous the bookig is rejected with the message "No time authorizatio". Topic 5.6 Table of error idetificatios Check for time authorizatio /2013 B-Cliet PDC6

107 Maual Commuicatio PIN check Ifo This parameter is primarily relevat if - PIN check is activated (limit value o. 21) - data type code is set. The etry of the PIN i the idividual master record of the employee or the pseudo master record is performed freely, 1-10 digits. The permitted characters are 0 to 9. The parameter defies if the etered keyboard data are to be compared to the PIN saved i the master record. If the etered keyboard data are compared to the PIN ad the data are ot idetical, the error idetificatio E: PIN false or missig is etered ito the data record. I the operatig modes Offlie/Autoomous the bookig is rejected with the message Code false". Topic 5.6 Table of error idetificatios PIN i master record Stadart settig after cold start: No special day idetificatio is saved. No time authorizatio is saved. No PIN check is performed. Ifo Topic Required dowload record B-Cliet PDC /

108 Commuicatio Maual Dowload record time profiles The parameters described i the previous sectios are modified i the termial usig the followig dowload record. Highlighted i gray: 1 st time pair GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio P h h m m h h m m... Block idetificatio P10 to PFE; see followig descriptio. Profile ame 01 hex to FE hex 00 = No time profile. Hour Start Miute Start Hour Ed Miute Ed Validity day Idetificatio bytes Time zoe A maximum of 6 more time pairs is possible Block idetificatio Durig dowload/upload the time profiles are differetiated accordig to the block idetificatio. If the time profiles i the termial are used, they are differetiated accordig to the profile ame. For a better overview, it is recommeded to select idetical 2d ad 3rd byte of the block idetificatio ad the profile ames, i.e. block idetificatio P01 correspods to the profile ame 01, etc /2013 B-Cliet PDC6

109 Pos: 26 @ 1 Maual Commuicatio Validity days The validity days are trasmitted i two bytes. The termial iterprets the characters etered i the dowload record as a hex code. 1. byte 2. byte Hex valecy Hex valecy Bit Bit Wedesday 0 = Ivalid 1 = Valid Tuesday 0 = Ivalid 1 = Valid Moday 0 = Ivalid 1 = Valid Reserved 0 Suday 0 = Ivalid 1 = Valid Saturday 0 = Ivalid 1 = Valid Friday 0 = Ivalid 1 = Valid Thursday 0 = Ivalid 1 = Valid Idetificatio bytes The termial iterprets the characters etered i the dowload record as a hex code. 1. byte 2. byte Hex valecy Hex valecy Bit Bit Special day idetificatio PIN check 0 = No 1 = Yes Reserved 0 Reserved 0 Reserved 0 Check for time authorizatio 0 = No 1 = Yes Ifo Topic Hexadecimale codig B-Cliet PDC /

110 Pos: 27 /KABA Kapitel (SW)/PDC6 1 Commuicatio Maual 2.22 Special day table The special days are importat if the master record refers to a time profile. Whe a bookig is made accordig to a time profile, the termial will check if the curret day is defied as a special day. If this is the case, the termial checks if a time pair exists for this special day. This check compares the special day idetificatio of the special day ad the special day idetificatio i the idetificatio bytes of the time pairs. If the special day idetificatio of ay time pair is idetical, this time pair is used. As a maximum 32 special days ca be defied i the special day table Date idicatio Fuctio of the parameter The termial iterprets the day with etered date as a special day. Stadard settig after cold start No special day is etered i the special day table. Ifo Topic Required dowload record Special day idetificatio Fuctio of the parameter The special day idetificatio is importat i the idetificatio bytes of the time profiles for the assigemet of the time pair. The special day idetificatio idetifies a valid time pair for a special day. To get a positive check result whe comparig the special day idetificatio i the time profile ad i the special day table, oly oe of the defied bits must match. Stadard settig after cold start No special day idetificatio is defied. Ifo Topic 2.21 Time profiles ad idetificatio bytes Required dowload record /2013 B-Cliet PDC6

111 Pos: 28 @ 1 Maual Commuicatio Dowload record special day table The parameters described i the previous chapters are modified i the termial usig the followig dowload record. The 32 possible special day defiitios are trasmitted to the termial with four dowload records which have the block idetificatios L01 to L04. Highlighted i gray: 1 st special day. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio L 0 Block idetificatio L01 to L04 M M T T Moth Day Special day idetificatio 0 Reserved 0... Max. 7 more special days possible. Special day idetificatio The termial iterprets the characters etered i the dowload record as a hex code which cotais several parameters Hex valecy Bit Special day idetificatio Reserved 0 Ifo Topic Hexadecimal codig B-Cliet PDC /

112 Pos: 29 /KABA Kapitel (SW)/PDC6 1 Commuicatio Maual 2.23 Texts Fuctio key texts Fuctio of the parameter If the termial is ready for bookigs, the fuctio key text is displayed i the upper lie of the display. The fuctio key text cosists of 30 characters max. ad ca be defied arbitrarily. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start Fuctio key BI (comp.) BI (multi) Fuctio key text Basic state M00 m00 Select fuctio F1 M01 m01 I Cost ceter tab Operatio tab Times tab F2 M02 m02 Out F3 M03 m03 Official absece F4 M04 m04 Query F5 M05 m05 Special fuctio F6 M06 m06 Start of operatio F7 M07 m07 Iterrupt operatio F8 M08 m08 Ed of operatio F9 M09 m09 F10 M10 m10 F11 M11 m11 Alterate cost ceter F12 M12 m12 Log off cost ceter F13 M13 m13 Book cost ceter F14 M14 m14 F15 M15 m15 Ifo Topic Required dowload record /2013 B-Cliet PDC6

113 Maual Commuicatio Dialog texts Fuctio of the parameter If the termial is ready for bookigs, the dialog text is displayed i the lower lie of the display. The dialog text cosists of 20 characters max. ad ca be defied arbitrarily. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadart settig after cold start Dialog text o. BI (comp.) BI (multi) Dialog text 1 D01 d01 Preset the 2. badge 2 D02 d02 Machie umber 3 D03 d03 Fault reaso 4 D04 d04 Order umber 5 D05 d05 Process code 6 D06 d06 Actual quatity 7 D07 d07 Deviatio reaso 8 D08 d08 Iterrupt reaso 9 D09 d09 Persoal umber 10 D10 d10 Idirect cost code 11 D11 d11 Replacemet badge 12 D12 d12 Date 13 D13 d13 Badge umber 14 D14 d14 SP-No. from 15 D15 d15 till 16 D16 d16 +/- hours 17 D17 d17 Correctio of days 18 D18 d18 Commad 19 D19 d19 ORG-GR/BST 20 D20 d20 VON/SYS-REG 21 D21 d21 I 22 D22 d22 Out 23 D23 d23 Query 24 D24 d24 Official absece 25 D25 d25 Scales Ifo Topic Required dowload record B-Cliet PDC /

114 Commuicatio Maual Fix-Texte The fix texts are oly importat if the iput uit "Fix text" is defied i a sigle fuctio block Fuctio of the parameter A stored fix text ca be etered ito the recordig data record. The fix text ca be defied arbitrarily. A maximum of 5 fix texts may be defied, each cosistig of 20 characters max. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start Text o. BI (comp.) BI (multi) T26 t26 Digit Text L e e r z e i c h e (B l a k s) T27 t27 Digit Text T28 t28 Digit Text ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ T29 t29 Digit Text * * * * * * * * * * * * * * * * * * * * T30 t30 Digit Text Ifo Topic Required dowload record /2013 B-Cliet PDC6

115 Maual Commuicatio Geeral texts Fuctio of the parameter Geeral texts have a special meaig ad are used to iform the user. As some of the texts are assiged to possible errors, we recommed to chage the text oly for traslatios ito other laguages to maitai their sese. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start BI (comp.) BI (multi) Geeral text T31 t31 Select fuctio T32 t32 Please wait T33 t33 Thak you T34 t34 Error: lower limit T35 t35 Error: upper limit T36 t36 Error: limit value T37 t37 Error: o umeric T38 t38 Repeat etry T39 t39 Not authorized T40 t40 No data trasmissio T41 t41 Iput error T42 t42 Parameter error T43 t43 No master record T44 t44 Versio umber wrog T45 t45 Error: versio check T46 t46 Master record blocked T47 t47 No correctio auth T48 t48 No off. absece auth. T49 t49 I/Out error T50 t50 Code o. false T51 t51 Error: code check T52 t52 Error: uavailable T53 t53 Error: ivalid etry B-Cliet PDC /

116 Commuicatio Maual BI (comp.) BI (multi) Geeral text T73 t73 Iput time-out T74 t74 No time auth. T75 t75 No dialog possible T76 t76 Termial blocked T77 t77 Ed of dialog T78 t78 Key ot allowed T79 t79 Dialog request T80 t80 Read error Ifo Topic Required dowload record Texts for register tabs Fuctio of the parameter The register tab texts specify the idividual fuctio groups ad ca be set arbitrarily via dowload. The texts may cosist of up to 30 characters, however oly 10 characters may be displayed max., depedig o the text cotet. Stadard settig after cold start Register tab o. BI (comp.) BI (multi) Register tab text 1 MA1 ma1 Time 2 MA2 ma2 Operatio 3 MA3 ma3 Cost ceter Ifo Topic Required dowload record /2013 B-Cliet PDC6

117 Maual Commuicatio Mailbox texts To display a mailbox text after a authorized bookig, the umber of the desired mailbox text must be etered i the logical bookig respose (R4 to R6 record) or i the master record resp. Fuctio of the parameter The mailbox text is a iformatio for the clockig employee ad cosists of up to 20 characters max. The mailbox text ca be defied arbitrarily. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start Mailbox text o. BI (comp.) BI (multi) Mailbox text 1 B01 b01 Mailbox text 1 2 B02 b02 Mailbox text 2 3 B03 b03 Mailbox text 3 4 B04 b04 Mailbox text 4 5 B05 b05 Mailbox text 5 6 B06 b06 Mailbox text 6 7 B07 b07 Mailbox text 7 8 B08 b08 Mailbox text 8 9 B09 b09 Mailbox text 9 10 B10 b10 Mailbox text B11 b11 Mailbox text B12 b12 Mailbox text B13 b13 Mailbox text B14 b14 Mailbox text B15 b15 Mailbox text 15 Ifo Topic 3.7 Master records Logical bookig respose with text Required dowload record B-Cliet PDC /

118 Commuicatio Maual Display ifo texts To display a display ifo text after a authorized bookig, the umber of the desired display ifo text must be etered i the logical bookig respose (R4 to R5 record) or i the master record resp. Fuctio of the parameter The display ifo text is a iformatio for the clockig employee ad cosists of up to 20 characters max. The display ifo text ca be defied arbitrarily. The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start Display ifo text o. BI (comp.) BI (multi) Display ifo text 1 I01 i01 Flextime balace 2 I02 i02 Holidays 3 I03 i03 Overtime 4 I04 i04 Extra work 5 I05 i05 Display ifo text 5 6 I06 i06 Display ifo text 6 7 I07 i07 Display ifo text 7 8 I08 i08 Display ifo text 8 9 I09 i09 Display ifo text 9 10 I10 i10 Display ifo text 10 Ifo Topic 3.7 Master records Logical bookig respose with text Required dowload record /2013 B-Cliet PDC6

119 Maual Commuicatio List texts Keyboard iputs durig a bookig procedure ca also be realized via lists. I this case, the employee ca pick from a list of various texts. Fuctio of the parameter The list text is a defied proposal for the employee ad cosists of up to 20 characters max. The list text ca be defied arbitrarily The block idetificatio (BI) i the dowload record is selected accordig to the desired laguage (compatible mode or multiligual). See the followig table. Stadard settig after cold start List text o. BI (comp.) BI (multi) List text 0 N00 00 Lack of material 1 N01 01 Break of tool 2 N02 02 Coolat error 3 N03 03 Geeral disturbace 4 N04 04 Not specified 5 N05 05 Machie disturbace 6 N06 06 Atedated order 7 N07 07 List text 7 8 N08 08 List text N96 96 List text N97 97 List text N98 98 List text N99 99 List text 99 Ifo Topic 2.18 List iput Required dowload record B-Cliet PDC /

120 Commuicatio Maual Dowload record compatible ad multiligual texts The compatible ad multiligual texts described i the previous chapters are modified i the termial usig the followig two dowload records. The block idetificatio is used to differ betwee the compatible ad multiligual texts. Texts with compatible block idetificatio are oly used if o etry was made i the b-cliet_pdc6.ii file i the [Laguages] sectio. I the followig dowload record example, the phrase Dake (= Thak you) is stored i the termial as geeral text T33. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio T Block idetificatio M00 to M15, MA1 to MA3, D01 to D25, 3 T26 to T53, T73 to T80, B01 to B15, 3 I01 to I10, N00 to N99 D a k e Text, 20 or 30 (= fuctio key texts) chacters max. Ifo Topic 6.5 Laguages sectio of the b-cliet_pdc6.ii file /2013 B-Cliet PDC6

121 Pos: 30 @ 1 Maual Commuicatio The multiligual fuctio ca be used durig the bookig procedure. I this case the laguage of ay text will chage after operatig the laguage switchover symbol. The correspodig texts are stored i the termial via the followig dowload record. This dowload record cotais a additioal laguage idetificatio ad uses a lower case letter i the first digit of the block idetificatio. I the followig dowload record example, the phrase Thak you is stored as the geeral text t33 i the termial. The laguage idetificatio for Eglish Great Britai is used. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio t Block idetificatio m00 to m15, ma1 to ma3, d01to d25, t26 to t53, 3 t3 to t80, b01 to b15, 3 i01 to i10, 00 to 99 e G B T h a k y o u Laguage idetificatio (6 digits) Space (20 hex ) Space (20 hex ) Text, 20 or 30 (= fuctio key texts) chacters max. Laguage idetificatio The laguage idetificatio cosists of 6 digits. Digit 1 ad 2 represet the laguage, digit 3 ad 4 represet the coutry. The digits 5 ad 6 are without ay meaig at the momet ad filled up with spaces (20 hex). If o coutry idetificatio is eeded, digits 3 ad 4 ca also be filled up with spaces. Ifo Topic 6.5 Laguages sectio of the b-cliet_pdc6.ii file. 5.7 Table of laguage idetificatios B-Cliet PDC /

122 Data records from the host to the termial Maual Pos: 31 /KABA Kapitel (SW)/PDC6 Module/Datesätze Data records from the host to the termial 3.1 Display records The followig chapters explai the fuctio of each sigle data record. Fuctio of the parameter The followig display records allow to display user iformatio. The user iformatio may cosist of up to 80 characters max. I the user iformatio cotais more tha 80 characters, the remaiig characters are cut off. GID DID ON/OFF D. Group address Device address Operatig mode Record type Record type modificatio, see followig table User iformatio, 80 characters max. RT/RTM D0 D1 D2 Descriptio Static display With the followig data record a user iformatio ca be displayed idepedetly from a bookig. The user iformatio is displayed as log as a ew iformatio, e.g. a logical bookig respose, is displayed. Dyamic display authorized With the followig data record a user iformatio ca be displayed idepedetly from a bookig. The user iformatio is deleted from the display after a defied time ad the termial returs to its basic state. The display time is defied with the Display duratio Authorized parameter. Dyamic display ot authorized With the followig data record a user iformatio ca be displayed idepedetly from a bookig. Additioally, a acoustic sigal is geerated by a beeper. The user iformatio is deleted from the display after a defied time ad the termial returs to its basic state. The display time is defied with the parameter Display duratio Not authorized. Ifo Topic Display duratio Authorized Display duratio Not authorized /2013 B-Cliet PDC6

123 Maual Data records from the host to the termial 3.2 Dialog records (G dialog) Fuctio of the parameter The data records i this chapter are oly relevat if the termial is i the olie operatig mode ad a fuctio key is set as a dialog key G dialog compariso to fixed bookig procedure Fixed bookig procedure A fixed bookig procedure ca be assiged to a fuctio key usig idividual fuctio blocks. Up to 18 iput steps ca be defied per key, they are requested by the termial. There are o restrictios for the variety of the requiremets. This is true ot oly for the umber of iput steps but also for the texts ad iformatio to be displayed at the termial. The static bookig procedure usig idividual fuctio blocks ca, therefore, ot always cover all requiremets. G dialog If a fuctio key has bee defied as dialog key, all user iputs are performed i a dialog with the host (G dialog). The host will decide dyamically whether ad what iputs are required ad which iformatio must be displayed for the user. This exteds the desig optios of the user dialog sigificatly G dialog procedure The G dialog is started by pressig a fuctio key at the termial. The termial seds a G8 record (dialog request) cotaiig the record type ad record type modificatio set for the fuctio key. After receivig the G8 record, the host will sed the first G0 record (dialog mask) to the termial. The G0 record cotais iformatio o: the iput value (type, umber of characters, from which positio, etc.) the reader type to be used (bar code, keyboard, etc.) etry, ifo ad user guidace texts The termial respods to the G0 request of the host by sedig a G1 record (dialog iput). The recorded iput data are trasmitted to the host accordig to the format specificatios of the G0 record. After evaluatig the data, the host will decide whether further etries are required ad, if ecessary, sed more requests to the host i the form of G0 records. The dialog ca be termiated either by the termial or the host by sedig the G9 record. The host will ed the dialog if o more iput steps are active or errors occur i the dialog. The termial will ed the dialog, for example, after the dialog key is pressed agai by the user or after a time-out, etc. B-Cliet PDC /

124 Data records from the host to the termial Maual Termial settigs for G-dialog records the desired fuctio key must be defied as a dialog key. record type ad record type modificatio must be assiged to the fuctio key usig the sigle fuctio blocks. the termial must be i the Olie operatig mode. Ifo Topic Fuctio key as dialog key Sigle fuctio blocks Switch over the operatig mode G dialog example Termial Host Actio Fuctio block Select fuctio G8 (Start) Start the G dialog G0 (Request) Step 1: Eter badge Sed request record Eter badge G1 (Data) Data evaluatio G0 (Request) Step 2: Eter order o. Sed request record Eter order o. G1 (Data) Data evaluatio further G dialog steps.. Ed of setup G9 (Ed) Step x: Ed of G dialog Sed the ed record with mask text or error text /2013 B-Cliet PDC6

125 Maual Data records from the host to the termial Dialog mask The termial expects the followig data record from the computer after a dialog request by meas of the G8 record. The followig data record ca also be trasmitted to the termial without a dialog request. The dialog mask defies which iputs are required. The etered user iformatio appears o the display. The etries are trasmitted from the termial to the computer by meas of a G1 record. After that it is either possible to trasmit aother G0 record or a G9 record to the termial. GID DID ON/OFF Group address Device address Operatig mode G Record type 0 Record type modificatio. Keyboard etry; see followig descriptio Iput uit; see followig descriptio Display badge cotet; see followig descriptio From digit with badge iput; see followig descriptio Number of digits; see followig descriptio Positio i the user iformatio used for default value (00: o specificatio) Type of the iput field; see followig descriptio Display of user iformatio; see followig descriptio User iformatio (max. 40 digits) Ifo Topic G8 record G1 record G0 record B-Cliet PDC /

126 Data records from the host to the termial Maual Keyboard etry This etry defies if a keyboard etry is ecessary. Etry Meaig 0 No keyboard etry 1 Numeric keyboard etry 2 Alphaumeric keyboard etry Iput uit This etry defies if a reader is to be used for the iput. Etry Meaig 0 No reader iput A or a B or b C or c Reader 1 Iput uit is released Reader 1 Iput uit is released Reader 2 Iput uit is released Reader 1 Iput uit is ot released Reader 1 Iput uit is ot released Reader 2 Iput uit is ot released Display badge cotet This etry defies if the badge cotet is displayed. The rage limited by the etries "From digit with badge iput" ad "Number of digits" is displayed. The displayed data must be cofirmed by the "E" (eter) key. Etry Meaig 0 Do ot display badge cotet 1 Display badge cotet /2013 B-Cliet PDC6

127 Maual Data records from the host to the termial From digit upo badge iput This iput defies the positio from which the badge cotets are etered ito the G1-record. Possible values: 01 through 99, where 01 meas, badge cotets from first digit. Ifo Topic G1 record Number of digits For a badge iput, this etry used to defie how may digits of the read badge cotets are to be etered ito the G1-record. For a keyboard iput, this etry defies how may digits are to be etered ad are etered ito the G1-record. Possible values: 01 through 40 (badge iput) 01 through 40 (keypad iput) 00: the first operated key will be etered ito the G1-record ad trasmitted directly to the host. The etry must be cofirmed with the Eter key. Positio withi the user iformatio used for default value This parameter defies from which digit the characters of the user iformatio will be etered as a default value ito the iput field. Possible values: 00 through = o default Type of iput field These settigs defie the kid of keypad iput ad their represetatio i the display. If "Keypad iput rollig" has bee set, the etered characters are rolled through the display from right to left. If fewer digits are etered as defied by "Number of digits", leadig blaks (20 hex ) are etered. If "Keypad iput fixed" has bee set, the iput locatios are preallocated with dashes -. The cursor is o the outermost left digit. With each digit that is etered, the cursor will move oe digit to the right. If fewer digits are etered as defied via "Number of digits", the dashes are preserved. The keyboard iput ca be displayed i the followig ways: as data: the iput is visibile o the display as code: the iputs are show o the display as a asteriks character (*) hidde: the iputs are ot visible o the display. B-Cliet PDC /

128 Data records from the host to the termial Maual Possible values: 0 = 1 = 2 = 3 = 4 = 5 = Keyboard iput rollig fix rollig fix rollig fix Character The etered characters are displayed. Each etered character is displayed as "*". The etered characters are ot displayed. Ifo Topic G1 record User iformatio with acoustic sigal This etry defies whether the user iformatio output is accompaied by a acoustic sigal. If the user iformatio is output, o iput parameters must be set. The termial iterprets a G0 record as set data iput ad blikig user iformatio as parameter settig error, rejectig the received G0 record by meas of a O1 record. Etry Meaig 0 No acoustic sigal 1 Acoustic sigal 2 Positive ackkowledge after eterig a badge User iformatio Text output, 40 characters max /2013 B-Cliet PDC6

129 Maual Data records from the host to the termial Dialog iput The termial trasmits the followig data record to the computer after a G0-record has bee received ad whe the required data has bee etered. Afterwards, aother G0 record or a G9 record ca be trasmitted to the termial. GID Group address DID Device address ON/OFF Operatig mode G Record type 1 Record type modificatio Iformatio byte; see followig descriptio. Iput data Iformatio byte Etry Meaig Iput data i the G1 ecord 0 Iput was aborted with "C" key No iput data 1 Iput was completed with "E key I accordace to user iput 2 Key "->" was operated No iput data 3 Key "-<" was operated No iput data 4 Alphaumeric key was operated Character of the touched key 5 Operatio timeout expired I accordace to user iput 6 Reader iput I accordace to user iput The etries 2, 3 ad 4 ca oly appear if keyboard iput with umber of digits = 00 has bee set i the termial with a G0 record. Ifo Topic Dialog mask (G0 record) G9 record B-Cliet PDC /

130 Data records from the host to the termial Maual Dialog request If a fuctio key is defied as dialog key ad the dialog is ot blocked, the termial will trasmit the followig data record to the computer after the fuctio key has bee touched. After that, the termial expects a G0-record from the host computer. GID DID ON/OFF G Group address Device address Operatig mode Record type 8 Record type modificatio. Cotet: RT/RTM of the operated fuctio key; see followig descriptio 6 digits user laguage idetificatio; oly if set as a parameter. Cotet: RT/RTM of the operated fuctio key The cotet is defied by the Cotet of G8-record parameter. It is either G8 or the RT/RTM of the fuctio key which has started the dialog request. The RT/RTM of the fuctio keys are defied by the parameters record type ad record type modificatio. Tag for user laguage This tag cotais the predefied or user choose laguage. The tag will be trasmitted oly if the parameter "User laguage i data record is set. Ifo Topic Block dialog G0 record Record type / record type modificatio User laguage i data record /2013 B-Cliet PDC6

131 Maual Data records from the host to the termial Dialog ed The followig data record sigals the ed of the dialog. This data record must be trasmitted to the termial after the ed of the dialog to perform a ed idetificatio. The etered user iformatio is displayed. If o user iformatio is etered, the iteral bookig respose "Dialog ed" is displayed. GID Group address DID Device address ON/OFF Operatig mode G Record type 9 Record type modificatio. User iformatio, 80 characters max. B-Cliet PDC /

132 Data records from the host to the termial Maual 3.3 Termial cotrol Request status of the iputs I/O Fuctio of the data record The followig data record requests the curret status of the iputs. I respose, the termial trasmits a H1-record to the host computer. GID Group address DID Device address ON/OFF/AUTO Operatig mode H Record type 8 Record type modificatio Ifo Topic H1 record Block / release bookigs Fuctio of the data record With the followig data record, the termial ca be blocked or released for bookigs. If the termial is blocked, while a bookig is active, the curret bookig process ca be fiished. If the termial is blocked, the message "Termial blocked" is displayed. GID DID ON/OFF I Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio Record type modificatio Etry Meaig 0 Release bookigs 1 Block bookigs /2013 B-Cliet PDC6

133 Maual Data records from the host to the termial Local biometrics maagemet eabled/blocked This fuctio is curretly ot implemeted. LEN Fuctio of the data record The followig data record allows to block or eable the local biometrics maagemet at termials equipped with a CBM reader module. If the termial is blocked durig a parameterizig procedure, the process will be caceled with the ext meu chage. The message Not authorized will be show o the display. GID DID ON/OFF I Group address Device address Operatig mode Record type Record type modificatio, see followig descriptio Record type modificatio Etry Meaig 2 Release local biometrics maagemet 3 Block local biometrics maagemet Block / release dialog Fuctio of the data record With the followig data record the dialog ca be blocked or released. If the termial is blocked while a dialog process is active, the curret dialog process ca be fiished. If the correspodig fuctio key is operated the ext time, ot the defied dialog is started but all the other preset fuctio key fuctios are processed. GID DID ON/OFF I Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio Record type modificatio Etry Meaig 6 Release dialog 7 Block dialog B-Cliet PDC /

134 Data records from the host to the termial Maual Relay cotrol I/O Fuctio of the data record The followig data record allows to trigger the termial s relay idepedetly from a bookig. GID DID ON/OFF J Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio 0 Relay; see followig descriptio Record type modificatio Etry Meaig 0 Trigger relay statically 1 Trigger relay dyamically 2 Reset relay (if relay was triggered statically before) Relay Eter here the value 0 for relay1 Authorized. Other values have o fuctio. If relay 1 is triggered dyamically,the operatio time depeds o the Operatio time for relay 1 parameter. Etry Meaig 0 Relay 1; Authorized Ifo Topic Operatio time for relay /2013 B-Cliet PDC6

135 Maual Data records from the host to the termial Switchig termial i Olie, Offlie, Autoomous mode Fuctio of the data record The followig data record ca be used to switch the termial to the operatig modes Olie, Offlie or Autoomous. I the Olie operatig mode the termial has permaet data trasfer to the computer, i.e. geerated data records are immediately trasmitted to the computer. If a data record caot be trasmitted to the computer, the termial switches ito the operatig mode Offlie after the ed of 4x respose time-out. After the coectio has bee established, the termial switches agai ito the Olie operatig mode if the computer requests the data records. This process is carried out as follows: I the Offlie operatig mode, the data records are, first, trasmitted to the buffer memory. As soo as the coectio to the computer is established agai, it retrieves the data util the memory is empty. Now the termial switches back to Olie operatig mode. All geerated data records i the Offlie operatig mode are stored i the buffer of the termial. If there is a coectio to the computer, all saved data records are trasmitted to the computer. Alarm records, error records ad status records are trasmitted immediately from the priority buffer to the computer if a coectio ca be established. I the Autoomous operatig mode the geerated data records are saved i buffer of the termial. The computer must request these data records usig a T3 record. Alarm records, error records ad status records are immediately trasmitted to the computer provided a coectio ca be established. GID DID ON/OFF T Group address Device address Operatig mode Record type Record type modificatio, see followig descriptio. Record type modificatio Etry Meaig 0 Switch the termial to Olie mode 1 Switch the termial to Offlie mode 2 Switch the termial to Autoomous mode Ifo Topic Request data i the Autoomous operatig mode B-Cliet PDC /

136 Data records from the host to the termial Maual Requestig recordig data i the Autoomous operatig mode Fuctio of the data record The followig data record ca be used to request the data records buffered i the termial i the Autoomous operatig mode. GID Group address DID Device address ON/OFF Operatig mode T Record type 3 Record type modificatio Requestig termial state Fuctio of the data record The followig data record is used to request the curret termial state. The termial seds a S7 record as a respose to the computer. GID Group address DID Device address ON/OFF Operatig mode T Record type 4 Record type modificatio Ifo Topic S7 record /2013 B-Cliet PDC6

137 Maual Data records from the host to the termial Requestig program o. ad serial o. Fuctio of the data record The followig data record ca be used to request the program o. ad serial o. As a respose, the termial trasmits a SV record to the computer. GID DID ON/OFF Group address Device address Operatig mode T Record type 8 Record type modificatio Ifo Topic SV record Requestig backup state Fuctio of the data record The followig data record allows to request the backup state of the termial. The backup state is used by the termial to report which files have bee chaged sice the last backup modificatios. The termial seds a St record with the idetificatio B0 as a respose to the computer. GID DID ON/OFF T t B 0 Group address Device address Operatig state Record type Record type modificatio Idetificatio for backup request record Ifo Topic 3.12 St record with idetificatio B0 B-Cliet PDC /

138 Data records from the host to the termial Maual Deletig backup state Fuctio of the data record The followig data record allows to delete the backup state of the termial. For this purpose the bit values for RESET1 ad RESET2 are specified i the hexadecimal codig i which they have bee reported by the termial i the St record with idetificatio B0. The FTP server caot be disabled by meas of this deletio record. GID DID ON/OFF T t B 1 Group address Device address Operatig state Record type Record type modificatio Idetificatio for backup deletio record Bit values RESET1 The codig correspods to BUSTAT1 Bit values RESET2 The codig correspods to BUSTAT2 Ifo Topic 3.12 St record with idetificatio B Hexadecimal presetatio of characters /2013 B-Cliet PDC6

139 Maual Data records from the host to the termial Requestig reader iformatio Fuctio of the data record The followig data record is used to request iformatio o a reader of the Legic type SM As idetificatio for the reader, the umber uder which the requested reader is cofigured i the addressed termial must be etered. Possible values for the idetificatio: 1, 2 or 3. The termial seds a St record with the idetificatio T (= reader umber) as a respose to the computer. If the idetificatio i the data record addresses a reader type which does ot provide ay reader iformatio, the termial will sed a 03 record. GID DID ON/OFF T t T Group address Device address Operatig mode Record type Record type modificatio Reader idetificatio Ifo Topic St record with idetificatio T B-Cliet PDC /

140 Data records from the host to the termial Maual 3.4 Buffer cotrol Fuctio of the data record This data record provides differet fuctios for cotrol of the termial buffer memory usig record type modificatio. This data record is oly relevat if the "Buffer backup" parameter is set i the termial. GID DID ON/OFF M Group address Device address Operatig mode Record type Record type modificatio, see followig descriptio. RT/RTM M0 M1 M2 Descriptio Readig buffer All data records marked as trasmitted are trasmitted to the computer oce agai. Deletig buffer All trasmitted data records are deleted from the buffer memory of the termial. Iitializig buffer All data records are deleted from the buffer memory of the termial. Ifo Topic Set buffer backup /2013 B-Cliet PDC6

141 Maual Data records from the host to the termial 3.5 Logical bookig respose I/O Fuctio of the data record After a bookig i the Olie mode, the termial trasmits the data record to the computer ad waits for a logical bookig respose. The logical bookig respose ca be trasmitted to the termial as dialog respose or as data record. If the termial does ot receive a logical bookig respose from the computer withi the time frame "4 x respose time-out", it switches to the operatig mode Offlie, saves the bookig i the memory ad displays the iteral bookig respose "Thak you" or the display ifo stored i the master record. To use the relay you always eed the Digital I/O optio! GID DID ON/OFF R. Group address Device address Operatig mode Record type Record type modificatio, see followig descriptio User iformatio, max. 80 characters RT/RTM R0 R1 Descriptio Silet cofirmatio The R0 record ca be trasmitted to the termial as a silet cofirmatio. No relays are triggered. The etered user iformatio is displayed. If o user iformatio is etered, the termial immediately returs to its basic state without ay further reactio. The display time is defied with the parameter Display duratio authorized. Bookig authorized The R1 record ca be trasmitted to the termial after a authorized bookig. The Authorized relay is activated i compliace with the "Select authorized relay" parameter. The etered user iformatio is displayed. If o user iformatio is etered, the iteral bookig respose "Thak you is displayed. The "Display duratio authorized" parameter defies the displayig time. B-Cliet PDC /

142 Data records from the host to the termial Maual RT/RTM R2 R3 R9 Descriptio Bookig ot authorized The R2 record ca be trasmitted to the termial after a uauthorized bookig. The etered user iformatio is displayed. If o user iformatio is etered, the iteral bookig respose "Not authorized displayed. The "Display duratio ot authorized" parameter defies the displayig time. The relay will ot be activated. Repeat iput The R3 record ca be trasmitted to the termial if the iput is to be repeated. The bookig is ot authorized. The etered user iformatio is displayed. If o user iformatio is etered, the iteral bookig respose "Repeat iput" is displayed. The "Display duratio ot authorized" parameter defies the displayig time. The relay will ot be activated. Prologatio of respose timeout The R9 record is used for prologatio of the respose timeout. The, the termial agai expects a logical bookig respose withi the prologed respose time. Ifo Topic Display time Authorized" Display time "Not authorized" Activate Authorized relay Respose time-out /2013 B-Cliet PDC6

143 Maual Data records from the host to the termial Bookig authorized with display ifo (R4 to R6-record) I/O Fuctio of the data record The followig data record ca be trasmitted to the termial after a authorized bookig. The the door opeer relay will be triggered depedig o the settigs of the Select relay parameters. Accordig to the etered mailbox text o. the correspodig mailbox text is displayed. If the mailbox text o. 0 is etered, o mailbox text is displayed. The display ifo text ad the correspodig display ifo are displayed istead. More display ifo ca be requested with a soft key. If either mailbox text or display ifo is defied, the iteral bookig respose "Dake" (Thak you) is displayed. The display duratio after a authorized bookig is defied with the "Display duratio authorized" parameter. The respose-specific text ca be used istead of Thak you, if o mailbox text o. ad o display ifo are defied. To use the relay you always eed the Digital I/O optio! GID DID ON/OFF R X... Group address Device address Operatig mode Record type Record type modificatio, see table below. Mailbox text o. 0-F (for mailbox text o or o mailbox text). Display ifo 1; umbers of characters 1, 8, 13 or 20, see table below. Up to 9 further display ifo; each cosistig a umber of characters defied with Rx, see table below. Respose specific text, 40 characters. B-Cliet PDC /

144 Data records from the host to the termial Maual Record type modificatio ad umber of characters RT RTM Number of characters i the display-ifo R 4 8 R 5 13 R 6 20 Ifo Topic Display time Authorized" Activate Authorized relay /2013 B-Cliet PDC6

145 Pos: 46 @ 1 Maual Data records from the host to the termial 3.6 Date / time Fuctio of the data record The followig data record is used to set the date ad time i the termial. If it is also ecessary to set secods, the RT/RTM U1 must be used. GID DID ON/OFF U J J M M T T h Group address Device address Operatig mode Record type Record type modificatio, see followig table (90 to 89 = 1990 to 2089) Date h m m (s) (s) Time. Specificatio of secods oly for RT/RTM U1. Record type /Record type modificatio RT RTM Settig secods U 0 No U 1 Yes B-Cliet PDC /

146 Pos: 47 /Software-Hadbücher/B-Cliet PDC10/Stammsätze 1 Data records from the host to the termial Maual 3.7 Master records The master record is built up of all iformatios which are stored i the termial accordig to a certai badge umber. It is possible to store iformatio regardig PIN umber, time profiles ad time balaces for each employee i the so-called Idividual master record. The bookig authorizatios for the termial are set by dowloadig the master records ad reset by deletig the master records. I the termial, differet kids of master records may exist: Idividual master records Oe pseudo master record Durig a bookig, first, it is checked if there is a idividual master record ad the, if it is ot available, if there is a pseudo master record. The master record detected first is used for the check. If the "Idividual master record required" parameter is activated, oly the idividual master record is searched for. The umber of master records that ca be loaded i the termial depeds o the licesed memory cofiguratio. If the permitted umber is exceeded i a master record dowload, the termial geerates a O2 error record (commad caot be executed at the momet). Idividual master record This master record is assiged to a ID o. read from a badge. All checks ad authorizatios cotaied i this master record are valid for this badge. Pseudo master record If o idividual master record ca be assiged to a badge, the pseudo master record is assiged. All checks ad authorizatios cotaied i this master record are valid for this badge. Oly oe pseudo master record ca be stored i the termial. Ifo Topic Parameter "Idividual master record required" Table of memory cofiguratio /2013 B-Cliet PDC6

147 Maual Data records from the host to the termial Idividual master record dowload The followig data record defies the parameters of the idividual master record. Highlighted i gray: i these digits wildcards * are allowed, i.e. the curret value i the termial remais uchaged GID Group address DID Device address ON/OFF Operatig mode Y Record type 0 Record type modificatio ID o., variable legth,. see followig descriptio Versio o., see followig descriptio Employee status; see followig descriptio Time profile ame; see followig descriptio. PIN, variable legth, see followig descriptio. 0 Reserved 0 Mailbox text o. 0-F (for mailbox text o or o mailbox text) see followig descriptio. Display ifo 1; 8 digits;. see followig descriptio Display ifo 2; 8 digits; see followig descriptio Display ifo 3; 8 digits; see followig descriptio Display ifo 4; 8 digits; see followig descriptio 11 digits reserved 0 B-Cliet PDC /

148 Data records from the host to the termial Maual Perso-related text, 40 characters see followig descriptio Text without special meaig, 20 characters e.g. available for parter applicatios Display ifo 5; 8 digits; see followig descriptio Display ifo 6; 8 digits; see followig descriptio Display ifo 7; 8 digits; see followig descriptio Display ifo 8; 8 digits; see followig descriptio Display ifo 9; 8 digits; see followig descriptio Display ifo 10; 8 digits; see followig descriptio Biometric status see followig descriptio Descriptio of parameters ID o. The idividual master record is valid for the badge with the ID umber etered i the master record. The legth of the ID o. is variable ad ca be set with a etry i the [MasterRecordDefiitio] sectio of the b-cliet_pdc6.ii file. Values from 1 to 18 ca be set for the ID-o. legth; the default legth is 7 digits. The ciphers 0 0 to 9 8 ca be etered here as a ID-o., depedig o the defied legth. ID-umbers exclusively cosistig of the cipher 9 are ot permitted here. If the ID umber of the badge is shorter tha the ID legth defied i the.ii file, leadig zeros must be etered as a prefix. Example: Eter if oly 5 bits of the defied ID legth of 7 digts is used /2013 B-Cliet PDC6

149 Maual Data records from the host to the termial If you wat to chage the ID-o. legth, please observe the followig: No master records are stored i the termial (delivery state) The chages i the b-cliet_pdc6.ii file take place after the FTP file trasfer to the termial. They are valid for the master records to be defied afterwards. A cold start of the termial is ot ecessary. Master records are alrady stored i the termial Master records which are already stored i the termial must be deleted before chagig the ID-o. legth. This ca either be doe usig - a Y1-record with the accordig umber of wildcards ( * ) or - a cold start. Versio o. The versio o. read from the badge must correspod with the ID o. etered i the master record. Employee status The employee status is trasmitted i 2 byte. The termial iterprets the characters etered i the dowload record as a hex code. A specialty is the use of wildcards (character * ), which ca be assiged to a sigle byte or for both. If you use wildcards, attetio should be paid to whether a master record is already i the termial or ot. If master records already exist i the termial ad a master record dowload with two wildcards takes place, the status etered i the termial remais uchaged. If o master record is i the termial yet, the wildcards cause a settig of the employee s status to the followig values: - default value 0 for byte 1 ad - default value 2 for byte 2 This meas that o authorizatio is assiged ad plausibility check is active. B-Cliet PDC /

150 Data records from the host to the termial Maual 1. byte Hex valecy Bit Official absece authorizatio 0 = No 1 = Yes Correctio authorizatio 0 = No 1 = Yes Idividual master record blocked 0 = No 1 = Yes Reserved 0 Bit 0 assigs a official absece authorizatio to the employee. If the used fuctio key is ot defied as iput filter ad "No official absece authorizatio" is assiged for a employee, error idetificatio J "No official absece authorizatio" is etered ito the recordig data record whe bookig o a fuctio key which has the RT/RTM B3, B4, or B5. I the operatig modes offlie/autoomous, the bookig is rejected with the message "No official absece authorizatio. If the used fuctio key is defied as iput filter ad "No official absece authorizatio" is assiged for a employee, a bookig with defied RT/RTM B3, B4, or B5 is rejected with the message "No authorizatio". Bit 1 assigs a correctio authorizatio to the employee. If the used fuctio key is ot defied as iput filter ad "No correctio authorizatio" is assiged for a employee, the error idetificatio K "No correctio authorizatio" is etered ito the recordig data record whe bookig o a fuctio key which has the RT/RTM B6. I the operatig modes offlie/autoomous the bookig is rejected with the message "No correctio authorizatio. If the used fuctio key is defied as iput filter ad "No correctio auhorizatio" is assiged for a employee, a bookig with defied RT/RTM B6 is rejected with the message "No authorizatio". Bit 2 allows to block the idividual master record. If the idividual master record is blocked, the error idetificatio M "Master record blocked" is etered ito the recordig data record. I the operatig modes off-lie/autoomous the bookig is rejected with the message "Master record blocked". Ifo Topic Fuctio key as iput filter Hexadecimal codig 5.6 Table of error idetificatios /2013 B-Cliet PDC6

151 Maual Data records from the host to the termial 2. byte Hex valecy Bit Employee preset 0 = No 1 = Yes Verify plausibility durig 1. bookig 0 = proceed accordig to bit 2 1 = No Verify plausibility 0 = Yes 1 = No Reserved 0 Bit 0 defies, whether the employee is preset or ot. This bit must be observed if the idividual master record is chaged durig the workig hours. After a upload of the idividual master record, this bit states if the employee is curretly preset. Bit 1 defies if a plausibility check is executed with the first bookig after dowload of the idividual master record. Bit 2 defies if the plausibility check is executed cotiuously. If the plausibility check is set ad a preset employee excutes a "IN" bookig or a abset employee executes a "OUT" bookig, the error idetificatio L "I/out error (plausibility error)" is etered ito the recordig data record. I the operatig modes offlie/autoomous the bookig is rejected with the message "I/out error Ifo Topic Hexadecimal codig 5.6 Table of error idetificatios Time profile ame To carry out checks accordig to time profiles, the profile ame of the desired time profile must be etered here, see chapter The etry 00 meas, o valid time profile is stored for this employee ad a check o time authorizatios provides a egative check result. Irrespective of this etry, a check for time authorizatio always takes place if it is set i the "Fuctio key fuctios". B-Cliet PDC /

152 Data records from the host to the termial Maual PIN I the time profile ad/or the code cotrol byte, a PIN check ca be activated. Durig the PIN check, the PIN etered via the keypad is compared with the PIN etered here i the idividual master record. PIN legth: variable betwee 1 ad 10 digits Valid characters: 0 to 9 Default legth: 4 digits Chagig: i the b-cliet_pdc6.ii file i the [MasterRecordDefiitio] sectio If you wat to chage the PIN, please observe the followig: No master records are stored i the termial (delivery state) The chages i the b-cliet_pdcx.ii file take place after the FTP file trasfer to the termial. They are valid for the master records to be defied afterwards. A cold start of the termial is ot ecessary. Master records are alrady stored i the termial Master records which are already stored i the termial must be deleted before chagig the ID-o. legth. This ca either be doe usig - a Y1-record with the accordig umber of wildcards ( * ) or - a cold start. Mailbox text o.0 to F ad Display ifo 1 to 10 Mailbox text o. 0-F or display ifo 1 to 10 are displayed after a authorized bookig i the offlie or autoomous operatig mode after a authorized bookig i olie operatig mode, if a R4 to R6-record without mailbox text umber ad display ifo is set to the termial. The display ifo ca be suppressed via certai fuctio key settigs Accordig to the etered mailbox text o. the correspodig mailbox text stored i the termial is displayed. The mailbox text is displayed oce with the first bookig after the master record dowload. If the mailbox text o. 0 is etered, o mailbox text is displayed. Istead, the display ifo is displayed. More display ifo ca be requested via a soft key. Persoal text This parameter is oly importat, if the Show persoal text parameter is set. The persoal text is show istead of a positive bookig aswer ("Thak you ). Text without defied meaig This text is iteded for program expasios (e.g. parter applicatios) ad is ot used otherwise /2013 B-Cliet PDC6

153 Maual Data records from the host to the termial Biometric status This parameter is curretly ot implemeted Some users may have problems whe bookig with a figer because of poor figer prit characteristics. Usig this byte, these persos may be authorized to eter their badge umber maually usig the keypad. If a badge umber is etered o master record is defied for, the bookig is rejected with the message Kei Stamsatz (o master record). If the fuctio key parameter Buffer ot authorized recordig data is set, the bookig is stored with the error idetificatio D Kei Stammsatz (o master record). If a badge umber is etered a master record is defied for but it s biometric status is set to 0, the bookig is rejected with the message Nicht berechtigt (ot authorized). If the fuctio key parameter Buffer ot authorized recordig data is set, the bookig is stored with the error idetificatio O Keie Ausweisummer Eigabe Berechtigug (o badge umber etry authorizatio) Hex valecy Bit Reserved 0 Reserved 0 Alterative badge umber etry authorizatio via keypad 0 = No 1 = Yes Alterative badge umber etry authorizatio via badge 0 = No 1 = Yes Ifo Topic 2.21 Time profiles Check for time authorizatio Logical bookig respose with texts Display perso related texts Suppress display ifo B-Cliet PDC /

154 Data records from the host to the termial Maual Idividual master record deletio With the followig data record a idividual master record ca be deleted i the termial. To do so, the ID umber of the idividual master record to be deleted must be etered. If all idividual master records i the termial shall be deleted, the appropriate umber of wildcards * ca be etered istead of the ID umber. This will also delete the pseudo master record. Partial cacellatio of master records usig a combiatio of characters ad wildcards is ot possible. ATTENTION Icorrect use of wildcards Loss of all master records after dowload Before dowloadig a deletio record with wildcards, make sure that the correspodig master records are permitted for deletio. If you are usure about the deletio of master records, do ot use ay wildcards or create a backup of the master records before sedig the deletio record. GID DID ON/OFF Group address Device address Operatig mode Y Record type 1 Record type modificatio. ID o., umber of digits depedig o the defiitio /2013 B-Cliet PDC6

155 Maual Data records from the host to the termial Idividual master record request The followig data record requests a idividual master record from the termial. To do so, the ID umber of the requested idividual master record must be etered. If all idividual master records i the termial shall be requested, the appropriate umber of wildcards ( * * * ) ca be etered istead of the ID umber. GID DID ON/OFF Y Group address Device address Operatig mode Record type 8 Record type modificatio. ID o., umber of digits depedig o the defiitio Idividual master record dowload ed The followig data record idicates the ed of the idividiual master record. It must be trasmitted to the termial as a ed idetificatio after the dowload of the idividual master record. GID DID ON/OFF Y Group address Device address Operatig mode Record type 9 Record type modificatio B-Cliet PDC /

156 Data records from the host to the termial Maual Pseudo master record dowload Highlighted i gray: i these digits wildcards * are allowed, i.e. the curret value i the termial remais uchaged GID Group address DID Device address ON/OFF Operatig mode Y Record type 0 Record type modificatio 9. Pseudo-ID, oly cipher 9 permitted.. Number of digits accordig to the defiitio digits reserved 0 0 Time profile ame; see followig descriptio. PIN, variable legth, see followig descriptio 0 Reserved Mailbox text o. 0-F (for mailbox text o or o mailbox text) see followig descriptio. Display ifo 1; 8 digits; see followig descriptio Display ifo 2; 8 digits; see followig descriptio Display ifo 3; 8 digits; see followig descriptio Display ifo 4; 8 digits; see followig descriptio 11 digits reserved 0 Perso-related text, 40 characters see followig descriptio /2013 B-Cliet PDC6

157 Maual Data records from the host to the termial Text without special meaig, 20 characters e.g. available for parter applicatios Display ifo 5; 8 digits; see followig descriptio Display ifo 6; 8 digits; see followig descriptio Display ifo 7; 8 digits; see followig descriptio Display ifo 8; 8 digits; see followig descriptio Display ifo 9; 8 digits; see followig descriptio Display ifo 10; 8 digits; see followig descriptio Biometric status, see descriptio i chapter Time profile ame To carry out checks accordig to time profiles, the profile ame of the desired time profile must be etered here, see chapter The etry 00 meas, o valid time profile is stored for this employee ad a check o time authorizatios provides a egative check result. Irrespective of this etry, a check for time authorizatio always takes place if it is set i the "Fuctio key fuctios". PIN I the time profile ad/or the code cotrol byte, a PIN check ca be activated. Durig the PIN check, the PIN etered via the keypad is compared with the PIN etered here i the idividual master record. PIN legth: variable betwee 1 ad 10 digits Valid characters: 0 to 9 Default legth: 4 digits Chagig: i the b-cliet_pdc6.ii file i the [MasterRecordDefiitio] sectio B-Cliet PDC /

158 Data records from the host to the termial Maual If you wat to chage the PIN, please observe the followig: No master records are stored i the termial (delivery state) The chages i the b-cliet_pdcx.ii file take place after the FTP file trasfer to the termial. They are valid for the master records to be defied afterwards. A cold start of the termial is ot ecessary. Master records are alrady stored i the termial Master records which are already stored i the termial must be deleted before chagig the ID-o. legth. This ca either be doe usig - a Y1-record with the accordig umber of wildcards ( * ) or - a cold start. Mailbox text o.0 to F ad Display ifo 1 to 10 Mailbox text o. 0-F or display ifo 1 to 10 are displayed after a authorized bookig i the offlie or autoomous operatig mode after a authorized bookig i olie operatig mode, if a R4 to R6-record without mailbox text umber ad display ifo is set to the termial. The display ifo ca be suppressed via certai fuctio key settigs Accordig to the etered mailbox text o. the correspodig mailbox text stored i the termial is displayed. The mailbox text is displayed oce with the first bookig after the master record dowload. If the mailbox text o. 0 is etered, o mailbox text is displayed. Istead, the display ifo is displayed. More display ifo ca be requested via a soft key. Persoal text This parameter is oly importat, if the Show persoal text parameter is set. The persoal text is show istead of a positive bookig aswer ("Thak you ). Text without defied meaig This text is iteded for program expasios (e.g. parter applicatios) ad is ot used otherwise. Ifo Topic 2.21 Time profiles Check for time authorizatio Logical bookig respose with texts Display perso relatetd texts Suppress display ifo /2013 B-Cliet PDC6

159 Maual Data records from the host to the termial Pseudo master record deletio The followig data record deletes the pseudo master record i the termial. GID DID ON/OFF Y Group address Device address Operatig mode Record type 1 Record type modificatio 9. 9 Pseudo-ID, oly cipher 9 permitted Number of digits accordig to the defiitio Pseudo master record request The followig data record requests the pseudo master record from the termial. GID DID ON/OFF Y Group address Device address Operatig mode Record type 8 Record type modificatio 9. 9 Pseudo-ID, oly cipher 9 permitted Number of digits accordig to the defiitio Pseudo master record dowload ed The followig data record idicates the ed of the pseudo master record. It must be trasmitted to the termial as a ed idetificatio after the dowload of the pseudo master record. GID DID ON/OFF Y Group address Device address Operatig mode Record type 9 Record type modificatio B-Cliet PDC /

160 Data records from the host to the termial Maual 3.8 Parameter dowload/upload Parameter upload request Termial parameters ca be requested usig the followig upload request. For this purpose, the block idetificatio of the requested parameters must be etered. The parameters ca also be requested by eterig wildcards * istead of the block idetificatio. E.g., the etry T * * as a block idetificatio will trasmit all geeral texts to the computer. GID Group address DID Device address ON/OFF Operatig mode > Record type 8 Record type modificatio Block idetificatio Ifo Topic 3.13 Parameter upload request with block idetificatio 2.13 Geeral termial parameters 0 Table of block idetificatios /2013 B-Cliet PDC6

161 Pos: 52 @ 1 Pos: 32 @ 1 Maual Data records from the host to the termial Parameter up / dowload record The termial trasmits the followig data record after a request from the host with the >8 record. The dowload must be carried out with a >3 record agai. GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio.. Block idetificatio of the requested parameter record The cotet of the data record cosists of the termial parameters depedig o the request Ed of parameter dowload The followig data record idicates the ed of a parameter dowload. The data record must be trasmitted to the termial as a ed idetificatio after a dowload of parameters. GID DID ON/OFF Group address Device address Operatig mode > Record type 9 Record type modificatio B-Cliet PDC /

162 Pos: 33 /KABA Kapitel (SW)/PDC6 Module/Datesätze 1 Data records from the host to the termial Maual 3.9 Data records from termial to computer Recordig data After a bookig the termial geerates a data record. The operatig mode of the termial determies whe this data record is trasmitted to the host. I the operatig mode Olie the procedure is as follows: the recordig data are checked accordig to the defied check criteria. the check result is etered as error idetificatio ito the data record. the data record is immediately trasmitted to the host. the host produces a logical bookig respose ad trasmits it to the termial specifyig whether the bookig is authorized or ot. if the termial does ot receive ay logical bookig respose from the host withi the respose time-out, it chages to the offlie operatig mode. I the operatig mode Offlie ad Autoomous the procedure is as follows: the recordig data are checked accordig to the defied check criteria. the check result is etered as error idetificatio ito the data record. accordig to the check result, the termial itself decides if the bookig is authorized or ot ad allows or blocks the access. the data record is ot trasmitted to the host, it is hadled accordig to the parameters "Buffer authorized recordig data" ad "Buffer ot-authorized recordig data". The etire legth of the bookig record show i the example is 32 Byte (without user laguage) calculated by the RT/RTM. This legth of the bookig record allows to save a certai umber of bookig records depedig o the cofiguratio. If the bookig record is exteded, the umber of bookig records that ca be saved is reduced correspodigly. Ifo Topic Switch operatig modes 5.6 Table of error idetificatios 3.5 Logical bookig respose Buffer recordig data /2013 B-Cliet PDC6

163 Maual Data records from the host to the termial GID DID ON/OFF/AUTO CI Y Y M M D D h h m m (s) (s) (l) (l) (c) (c) (v) (v) EI. Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter see followig descriptio 6 digits for the idetificatio of the user laguage; oly if set as a parameter. Error idetificatio Badge cotet ad keyboard data accordig to parameter settig Ifo Topic 5.4 Table of clock idetificatios Secods i data records Laguage i data record 5.6 Table of error idetificatios B-Cliet PDC /

164 Data records from the host to the termial Maual Record type/record type modificatio The record type / record type modificatio is defied by the "record type / record type modificatio" parameter. If the plausibility checks, the official absece authorizatio, ad the correctio authorizatio shall be used, the followig record types ad record type modificatios must be maitaied: Etry B1 B2 B3 B4 B5 B6 B0 BS BE Meaig Time recordig record I Time recordig record Out Busiess errad Auto I/Out Busiess errad I Busiess errad Out Correctio Iterrogatio Start of break Ed of break For productio data collectio the followig record type modificatios should be used: Etry FA... FZ Fa... Fz Meaig Productio data Ifo Topic Record type/record type modificatio /2013 B-Cliet PDC6

165 Maual Data records from the host to the termial 3.10 Error records The error records O1 to O3 cotai the data record which has triggered the error record. A list of the software optios for which there is o licese is added to the error record O5. GID DID ON/OFF/AUTO O... Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio Data record icludig RT/RTM which triggered the error record Record type modificatio Etry Meaig 1 Record cotet false 2 Commad caot be executed at the momet 3 Commad o-executable 5 No licese B-Cliet PDC /

166 Data records from the host to the termial Maual 3.11 Status records Reportig program o. The termial trasmits the followig data record after the request from the computer with a T8 record Request program o. GID DID ON/OFF/AUTO S V CI Y Y M M D D h h m m (s) (s). Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter. 6 digits for the idetificatio of the user laguage; oly if set as a parameter. Program o.; 12 digits e.g X-K00. Reserved; 12 digits blaks (20 hex ) Serial o.; 12 digits /2013 B-Cliet PDC6

167 Maual Data records from the host to the termial Report status of iputs I/O Fuctio of the data record The followig data record reports the status of the iputs. The termial comes with 2 iputs E1 to E2 The status of the iputs is reported to the computer i the followig cases: After request of the computer with a H8 record the termial reports the status of the iputs with a H1 record After the iput statuses have chaged, the termial reports the status of the iputs automatically with a H2 record. The H2 record will ot be geerated if the parameter E(X)SuppressAutomaticReport i the file b-cliet_pdc6.ii, sectio [IputsOutputs] is set. GID DID ON/OFF H CI Y Y M M D D h h m m (s) (s) Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio Clock idetificatio Date Time Secods ad user laguage oly if set as parameter Status of iput E1 Status of iput E2 Reserved 0.. Reserved 0 see followig descriptio The remaiig digits of the data record are reserved. B-Cliet PDC /

168 Data records from the host to the termial Maual Record type modificatio Etry 1 2 Meaig Data record was trasmitted after request from the host computer with H8 record. Data record was trasmitted automatically after chage of iput statuses. Status of iputs Etry Meaig 0 Iput ope 1 Iput closed 8 Chage of status: iput has bee closed 9 Chage of status: iput has bee opeed Ifo Topic 6.5 b-cliet_pdc6.ii Request status of the iputs (H8 record) 5.4 Table of clock idetificatios /2013 B-Cliet PDC6

169 Maual Data records from the host to the termial Buffer memory empty / Buffer memory full With the followig data record the termials reports to the computer whether the buffer memory is empty or full. The data record "Buffer memory empty" is oly trasmitted to the computer if the buffer memory cotet has bee read out completely. GID DID ON/OFF/AUTO S CI Y Y M M D D h h m m (s) (s). Group address Device address Operatig mode Record type Record type modificatio; see followig descriptio Clock idetificatio Date Time Secods oly if set as parameter. 6 digits for the idetificatio of the user laguage; oly if set as a parameter. Record type modificatio Etry Meaig 0 Buffer memory empty 2 Buffer memory full Ifo Topic 5.4 Table of clock idetificatios B-Cliet PDC /

170 Data records from the host to the termial Maual Local biometrics maagemet start/stop LEN This parameter is curretly ot implemeted. Fuctio of the data record The termial trasmits the followig data record to the host, if the local biometric maagemet has bee started (S3) or stopped (S4). The local biometric maagemet ca be started via the C-4-9 sequece ad a followig PIN if parameterized. If o PIN for the local biometrics maagemet is defied, please cofirm with the Eter key. I the local biometrics maagemet you fid, amog other features, the local erollmet fuctio. The local biometrics maagemet ca be left usig the C key or it is termiated time cotrolled after 70 secods without ay etry. Data records ca stil be sed or received, eve if the biometrics maagemet is i use. GID DID ON/OFF/AUTO S CI Y Y M M D D h h m m Group address Device address Operatig mode Record type Record type modificatio, see followig descriptio Clock idetificatio Date Time Secods ad user laguage idetificatio ca be set additioally as a parameter. Record type modificatio Etry Meaig 3 Local biometrics maagemet started 4 Local biometrics maagemet stopped Ifo Topic 5.4 Table of clock idetificatios /2013 B-Cliet PDC6

171 Maual Data records from the host to the termial Report termial status The termial trasmits the followig data record after request from the computer with a T4-record. GID DID ON/OFF/AUTO S Group address Device address Operatig mode Record type 7 Record type modificatio CI Y Y M M D D h h m m (s) (s). SYSTAT1 SYSTAT2 SYSTAT3 SYSTAT4 SYSTAT5 SYSTAT6 SYSTAT7 SYSTAT8 SYSTAT9 Clock idetificatio Date Time Secods oly if set as parameter. 6 digits for the idetificatio of the user laguage; oly if set as a parameter. System status; see followig descriptio B-Cliet PDC /

172 Data records from the host to the termial Maual SYSTAT1 The system status SYSTAT1 ca represet 2 values. After the termial has reported its status to the host computer, the SYSTAT1 status is set to 0. Etry Meaig 0 Received data records have bee ackowledged. 4 The computer trasmitted a data record with ukow record type, record type modificatio or block idetificatio. SYSTAT2 The system status SYSTAT2 ca represet 4 values. Etry Meaig 0 Bookigs are ot blocked curretly, o bookig is active 1 Bookigs are blocked curretly, o bookig is active 2 Bookigs are ot blocked curretly, a bookig is active 3 Bookigs are blocked curretly, a bookig is active SYSTAT3 The system status SYSTAT3 represets the status of the relay. Etry Meaig 0 No 1 Yes Relay activated SYSTAT4 The system status SYSTAT4 represets the status of the buffer memory. Etry Meaig 0 Buffer memory empty 1 Buffer memory ot empty 3 Buffer memory full SYSTAT5 The system status SYSTAT5 is iteded for extesios. A 0 is etered ito the data record /2013 B-Cliet PDC6

173 Maual Data records from the host to the termial SYSTAT6 The system status SYSTAT6 represets the status of the dialog mode. Etry Meaig 0 Dialog released 1 Dialog blocked SYSTAT7 The system status SYSTAT7 is iteded for extesios. A 0 is etered ito the data record. SYSTAT8 The system status SYSTAT8 represets the operatig mode of the termial. Etry Meaig 0 Operatig mode Olie 1 Operatig mode Offlie 3 Operatig mode Autoom SYSTAT9 Specific Kara Mifare system states are summarized i the system state 9. The presetatio of the states is carried out i form of a hexadecimal value accordig to the followig table. If several specified parameters are active, the correspodig values are added, see example Hex valecy Bit Key trasfer from programmig master permitted 0 = No 1 = Yes Productio key agaist applicatio key exchage eabled 0 = No 1 = Yes Reserved Reserved Example: Key trasfer from programmig master permitted is active Productio key agaist applicatio key exchage is eabled Etry i the SYSTAT9: 3 hex [bit 1 = 2 hex + bit 0 = 1 hex ---> = 3 hex ] Ifo Topic Hexadecimal codig B-Cliet PDC /

174 Data records from the host to the termial Maual Report backup state The termial records the chages for the selected files ad operatios if compared to the last message of the backup state. If this is the case, the correspodig hexadecimal value is writte i the data record ad reported to the host. If there have bee several chages, the correspodig hexadecimal values are added. The hexadecimal values are listed i 3 state descriptios BUSTAT1 to BUSTAT3, see the followig example. GID DID ON/OFF/AUTO S t CI Y Y M M D D h h m m B 0 BUSTAT1 BUSTAT2 BUSTAT3 Group idetificatio Device address Operatig state Record type Record type modificatio Clock idetificatio Date Time secods oly if set as parameter. Report idetificatio for backup state Hexcoded value for BUSTAT1 Hexcoded value for BUSTAT2 Hexcoded value for BUSTAT3 Ifo Topic 5.4 Table of clock idetificatios Request backup state Delete backup state Hexadecimal codig /2013 B-Cliet PDC6

175 Maual Data records from the host to the termial BUSTAT1 BUSTAT Hex value Hex value Bit Bit /Program/Share/Iit /Program/Share/User /Program/B-ClietPDC6/Iit /Program/B-ClietPD6/Images /Data/B-ClietPDC6/Data /Ram/EEPROMsettig Cold start performed Device restart performed BUSTAT Hex value Bit FTP server active Reserved 0 Reserved 0 Reserved 0 Example The followig files/states have bee modified at a termial: Program/Share/Iit Program/B-ClietPDC10/Iit Program/B-ClietPDC10/Images Device restart has bee performed The FTP server is active. The followig hexadecimal values i the data record result from these coditios: BUSTAT1: D hex [bit 3 = 8 hex + bit 2 = 4 hex + bit 0 = 1 hex ---> = D hex ] BUSTAT2: 8 BUSTAT3: 1 The states are deleted agai by trasmittig the deletio record "Delete backup state" with idetical hexadecimal values to the termial. The FTP server caot be disabled by meas of this deletio record. B-Cliet PDC /

176 Data records from the host to the termial Maual Report reader iformatio The termial seds the followig data record as a respose to a iquiry with a Tt record. The data record icludes the umber of the requested reader, as cofigured i the addressed termial. The idetificatio of the reader type is curretly always 01 for Legic SM The reader iformatio icludes, amog others, the boot loader versio ad the versio specificatio of the reader operatig systems. GID DID ON/OFF/AUTO S t CI Y Y M M D D h h m m. T Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time secods oly if set as parameter. 6 digits for the idetificatio of the user laguage; oly if set as a parameter. Reader idetificatio (reader ID) = 1, 2 or 3.. Type of reader 01 = Legic SM-4200 Reader iformatio for iteral use oly Ifo Topic Request reader iformatio /2013 B-Cliet PDC6

177 Maual Data records from the host to the termial 3.12 Master records Upload of idividual master record The termial trasmits the followig data record after the request from the computer usig a Y8 record Request idividual master record. GID DID ON/OFF Y Group address Device address Operatig mode Record type 0 Record type modificatio.. ID o.; umber of digits accordig to the defiitio Cotet of the master record Ifo Topic Request idividual master record Idividual master record B-Cliet PDC /

178 Data records from the host to the termial Maual Upload of pseudo master record The termial trasmits the followig data record after the request from the computer usig a Y8 record Request pseudo master record. GID DID ON/OFF Group address Device address Operatig mode Y Record type 0 Record type modificatio 9. Number of digits accordig to the defiitio. Cipher 9 is madatory. 9. Cotet of the pseudo master record Ifo Topic Request pseudo master record Pseudo master record Ed of idividual/pseudo master record upload The followig data record seds a sigal at the ed of the idividual / pseudo master records durig upload. It is trasmitted as the ed idetificatio to the computer. GID DID ON/OFF Group address Device address Operatig mode Y Record type 9 Record type modificatio /2013 B-Cliet PDC6

179 Pos: 34 @ 1 Maual Data records from the host to the termial 3.13 Parameter upload/dowload Parameter upload record The termial trasmits the followig data record upo request of the computer usig the >8 record "Parameter upload request". GID DID ON/OFF Group address Device address Operatig mode > Record type 3 Record type modificatio. Block idetificatio of the requested parameter record Depedig o the request the cotets of the data record are parameters stored i the termial. Ifo Topic Parameter upload request 2.13 Geeral termial parameter Ed of parameter upload The followig data record sigals the ed of parameter upload. It is trasmitted as the ed idetificatio to the computer. GID Group address DID Device address ON/OFF Operatig mode > Record type 9 Record type modificatio B-Cliet PDC /

180 Kaba Mifare proximity reader Maual Pos: 35 /KABA Kapitel (SW)/PDC6 Module/Mifare Kaba Mifare proximity reader 4.1 Geeral This chapter describes the itegratio ad cofiguratio of a Kaba Mifare proximity reader i Kaba termials ad the subtermial types B-web ad B-web For a better uderstadig, a bullet poit list gives you a overview of the uderlyig applicatio cocept. Kaba Mifare proximity readers are a part of a applicatio cocept developed by Kaba which combies the use of differet applicatios o a medium with a ew security cocept. The maximum istallatio protectio ad, at the same time, a easy hadlig ad high flexibility are guarateed. A cetral elemet is the security card. This security card geerates the istallatio key ad is highly ecrypted. The istallatio key is ever obvious. By meas of the security card, the system operators have cotrol over their system ad their badges. This security card is protected additioally by a PIN/PCI system. The system operators keep their security card i-house eve if they order badges. The basic poits of this applicatio cocept are: The istallatio key is automatically geerated ad always remais ivisible A oral or writte forwardig of the istallatio key is impossible Does ot require ay cetral poit for maagig the istallatio key Distributio of the istallatio key via programmig master card (stadaloe compoets) or commuicatio software (olie compoets) Each applicatio o a medium has its ow, specifically calculated applicatio key Use of a temporary itermediate key (productio key) for third party suppliers to produce media Detailed loggig of all importat processes The preset iformatio is subdivided ito the followig topics: Overview of the possible compoets of a istallatio Iheritace hierarchy of the differet cards Term defiitio List of applicatio cases Presetatio of all possible data records /2013 B-Cliet PDC6

181 Maual Kaba Mifare proximity reader 4.2 Kaba Mifare overview: cofiguratios The authorizatio media allow the system operator to start up systems or to make chages. I this cocept, three types of authorizatio media are used. Security cards of type A/B as smart card with chip Security cards of type C as RFID smart card Programmig master cards of type A/B as RFID card The followig chart shows possible cofiguratio optios. Two possible applicatio cases are show together. 1. Creatig cards over the card reader ad the Kaba media maager 2. Distributig the istallatio key via the B-web desktop reader. The istallatio key ca be distributed over the programmig master A/B to the termials or the stadaloe compoets. Kaba Media Maager Fig. 15: Possible system cofiguratios B-Cliet PDC /

182 Kaba Mifare proximity reader Maual 4.3 Kaba Mifare overview: Card hierarchy ad iheritace The followig graph shows the cards that ca be used i a system ad the possibilities for iheritig the card cotets. Hereby, the followig applies: With a security card A, all other cards, icludig a copy of A, may be created With a security card B, a security card C ad the programmig master cards A ad B ca be created, but o copy of B. With a security card C, oly the programmig master cards A ad B ca be created. Fig. 16: Overview of card hierarchy ad iheritace /2013 B-Cliet PDC6

183 Maual Kaba Mifare proximity reader 4.4 Kaba Mifare: Term defiitio Istallatio key The mai key of the istallatio. It is geerated usig security card A or B, ad it is ever trasparetly available (private). It is used to geerate all other keys i the security cocept. It is stored i all compoets with security chip. It is ecoded by meas of the security chip to distribute it i a istallatio. Istallatio key check sum The check sum of the istallatio key is a geerated check sum that is uique for the istallatio key. It has a legth of 8 bytes for each istallatio key. Applicatio key The key to idetify the applicatio o the user medium. Productio key The productio key is idepedet of the uique umber ad oly temporarily stored o the medium (betwee medium productio ad first use i the istallatio). The productio keys are trasferred to the card producer for producig cards. These keys are calculated withi the security chip (i the security card) based o the istallatio key. Whe first beig used i the istallatio, the security chip (i the desk reader or i a olie termial) chages back the productio key to a idividual applicatio key of this medium. Kaba media maager Software for Widows-based operatig systems for a simple ad secure geeratio ad admiistratio of authorizatio ad user media. Medium Geeral term for badges, key tags or keys. B-Cliet PDC /

184 Kaba Mifare proximity reader Maual Paret ifo Iformatio about the iheritace of rights with programmig master cards. Programmig master Umbrella term for the programmig masters A ad B. Programmig masters are RFID badges by meas of which the stadaloe compoets ca be iitialized ad cofigured. Programmig masters ca be cofigured specifically for the istallatio usig the security card. They are used for distributig the istallatio key to all compoets of the istallatio. Security card A Cotact smart card accordig to ISO It cotais a security chip for geeratig the istallatio key ad other safety-relevat fuctios. Each istallatio eeds miimum oe security card for iitializig. Up to 8 istallatio keys/exteral applicatio keys ca be geerated ad stored together with the applicatio cofiguratios i the security chip. Copies of this data ca be stored o further security cards A, B, ad C (backup, multiplicatio). The security card A is provided by Kaba. Security card B Descriptio see security card A. The security card B is created from a security card A; it cotais the same data. Other copies caot be geerated usig security card B. Security card C Cotact-free Mifare DESFire RFID card. It is created from a security card A or B; it cotais the same data. Other security cards C caot be geerated usig security card C. I a stadard cofiguratio, the security card C is provided by Kaba. UID Uique idetificatio of a medium with a legth of up to 10 bytes /2013 B-Cliet PDC6

185 Maual Kaba Mifare proximity reader 4.5 Applicatio cases The followig table cotais a short referece of the applicatio cases described i this documet. You will fid data records ad i-depth iformatio about the differet topics i the belogig sub-chapters. Applicatio case Chapter Maagig the istallatio keys 4.6 Exchagig productio key agaist applicatio key Maagig the istallatio keys Dowloadig the istallatio key Trasfer directio: Computer termial Fuctio With this data record, a istallatio key is set to a termial. There may be maximum 8 istallatio keys i a system. A check sum of the istallatio key ca be trasferred additioally. If a check sum is also trasferred, a existig istallatio key is overwritte if the trasferred check sum does ot match the oe of the set istallatio key. If a check sum is ot specified, the istallatio key is always overwritte. If the desigatio of the istallatio key is outside the permitted rage from 0 to 7, a O3 record (commad ot executable) is set. The respose to the 'TtS' data record is give with the 'StS' record. Ifo Topic StS record B-Cliet PDC /

186 Kaba Mifare proximity reader Maual GID DID ON/OFF T t S.. Group address Device address Operatig mode Record type Record type modificatio Idetificatio of the istallatio key, see the followig table 192 digits istallatio key 16 digits check sum Idetificatio Meaig S0 Set istallatio key 0 S1 Set istallatio key 1 S7 Set istallatio key /2013 B-Cliet PDC6

187 Maual Kaba Mifare proximity reader Result of istallatio key dowload Trasfer directio: Termial computer Fuctio The termial seds the followig data record i respose to a TtS record. The StS record idicates whether the dowload of the istallatio key was successful or ot. GID DID ON/OFF S t CI Y Y M M D D h h m m (s) (s) S Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter Idetificatio of the istallatio key (S0 to S7) Result, see followig table. Result Etry Meaig 0 Writig the istallatio key was successful 1 Writig the istallatio key was ot successful Ifo Topic TtS record B-Cliet PDC /

188 Kaba Mifare proximity reader Maual Deletig idividual istallatio key Trasfer directio: Computer termial Fuctio With this data record, a istallatio key is deleted i a termial. The respose to the 'TtD' data record is give with the 'StD' record. GID DID ON/OFF T t D Group address Device address Operatig mode Record type Record type modificatio Idetificatio of the istallatio key The istallatio key is selected based o the idetificatio i the data record accordig to the followig table: Idetificatio Meaig D0 Delete istallatio key 0 D1 Delete istallatio key 1 D7 Delete istallatio key 7 Ifo Topic StD record /2013 B-Cliet PDC6

189 Maual Kaba Mifare proximity reader Result of idividual istallatio key deletio Trasfer directio: Termial computer Fuctio The termial seds the followig data record i respose to a TtD record. The StD record idicates whether the deletio of the istallatio key was successful or ot. GID DID ON/OFF S t CI Y Y M M D D h h m m (s) (s) D Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as a parameter Idetificatio of the istallatio key (D0 to D7) Result, see followig table. Result Etry Meaig 0 Deletig the istallatio key was successful 1 The istallatio key could ot be deleted, or it does ot exist Ifo Topic TtD record B-Cliet PDC /

190 Kaba Mifare proximity reader Maual Deletig all istallatio keys Trasfer directio: Computer termial Fuctio With this data record, all istallatio keys are deleted i a termial. GID DID ON/OFF T t A 1 Group address Device address Operatig mode Record type Record type modificatio Delete all istallatio keys /2013 B-Cliet PDC6

191 Maual Kaba Mifare proximity reader Result of deletig all istallatio keys Trasfer directio: Termial computer Fuctio The termial seds the followig data record i respose to a TtA1 record. The StA1 record idicates whether the deletio of all istallatio keys was successful or ot. Whe performig a cold start of the termial, the istallatio keys are also deleted, ad this data record is set. GID DID ON/OFF S t CI Y Y M M D D h h m m (s) (s) A 1 Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter Idetificatio for "Delete all istallatio keys" Result, see followig table. Result Etry Meaig 0 Deletig all istallatio keys was successful 1 Deletig all istallatio keys was ot successful Ifo Topic TtA1 record B-Cliet PDC /

192 Kaba Mifare proximity reader Maual Distributig istallatio keys by meas of programmig masters A ad B This fuctio is required if there are stadaloe compoets i a istallatio i additio to olie termials. The istallatio keys caot be set to them over a olie coectio. O a programmig master A or B, all istallatio keys presetly beig used i a istallatio are stored. By bookig o a termial or stadaloe compoet, the istallatio keys are trasferred to the termial or the stadaloe compoet. If a programmig master A or B is detected durig bookig, the istallatio keys of the programmig master ad those of the stadaloe compoet/termial are sychroized. Hereby, the followig applies: All istallatio keys of the programmig master that do ot exist or have bee modified are trasferred. Istallatio keys i the termial/stadaloe compoet that are ot stored i the programmig master are deleted. Idividual istallatio keys caot be trasferred later o to the termial/stadaloe compoet by meas of the programmig master. This process is logged i 2 data records of the termial. This fuctio ca be eabled ad disabled by meas of data records (for olie termials). After a cold start of the termial, this fuctio is disabled, i.e. the istallatio keys caot be trasferred to the termial by meas of a programmig master. Ifo Topic Disablig/eablig the istallatio key trasfer Distributig the istallatio key ad reportig the check sum Distributig the istallatio key ad reportig the paret ifo /2013 B-Cliet PDC6

193 Maual Kaba Mifare proximity reader Disablig/eablig the istallatio key trasfer The trasfer of istallatio keys from a programmig master to the termial ca be eabled or disabled by meas of a data record. After a cold start of the termial, all istallatio keys of the termial are deleted. The fuctio "Trasfer istallatio key from programmig master" is disabled after a cold start. If you wat to use it, eable it previously by meas of a data record Disablig/eablig istallatio key trasfer Trasfer directio: Computer termial Fuctio The followig data record eables/disables the fuctio "Trasfer istallatio key from programmig master" i the addressed termial. GID DID ON/OFF T t Group address Device address Operatig mode Record type Record type modificatio A Idetificatio, see the followig table Idetificatio Meaig 2 Disablig the istallatio key trasfer from the programmig master 3 Eablig the istallatio key trasfer from the programmig master B-Cliet PDC /

194 Kaba Mifare proximity reader Maual Distributig the istallatio key ad reportig the check sum Trasfer directio: Termial computer Fuctio The termial seds the followig data record if you have tried to trasfer oe or several istallatio keys via the programmig masters A or B to the termial. The StB1 record idicates whether the trasfer of the istallatio key(s) was successful or ot. With a positive result (result = 0), the followig is trasferred together with the data record: 20 digits of the UID of the programmig master 128 digits of the check sum of the trasferred istallatio key(s). For each istallatio key, there are 16 available digits (= 8 bytes) for the check sum. If the trasfer of the istallatio key(s) failed (results= 1, 2, or 3), the UID ad the check sum are ot trasferred. Neither is the data record B2, which follows i case of success, trasferred i case of failure /2013 B-Cliet PDC6

195 Maual Kaba Mifare proximity reader GID DID ON/OFF S t CI Y Y M M D D h h m m (s) (s) B 1.. Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter Idetificatio "Report check sum of istallatio key" Result, see followig table. 20 digits for UID of the master 128 digits of the check sum of the istallatio key Result Etry Meaig 0 Trasfer of istallatio key successful 1 Trasfer of istallatio key ot successful 2 Trasfer of istallatio key disabled 3 No trasfer of istallatio key because a valid check sum has ot bee foud. B-Cliet PDC /

196 Kaba Mifare proximity reader Maual Distributig the istallatio key ad reportig the paret ifo Trasfer directio: Termial computer The termial seds the followig data record after the B1 record if you have trasferred oe or several istallatio keys via the programmig masters A or B to the termial. With a positive result (result = 0), the followig is trasferred together with the data record: 20 bytes of the UID of the programmig master 128 bytes of the paret ifo of the trasferred istallatio key(s). For each istallatio key, there are 16 available digits (= 8 bytes) for the paret ifo. If the trasfer of the istallatio key(s) failed (results= 1, 2, or 3), this data record is ot trasferred. GID DID ON/OFF S t CI Y Y M M D D h h m m (s) (s) B 2.. Group address Device address Operatig mode Record type Record type modificatio Clock idetificatio Date Time Secods oly if set as parameter Idetificatio "Report paret ifo of istallatio key" Result 0 = Trasfer of istallatio key successful 20 digits for UID of the master 128 digits for the paret ifo /2013 B-Cliet PDC6

197 Maual Kaba Mifare proximity reader Exchagig productio key agaist applicatio key Trasfer directio: Computer termial Fuctio Exteral compaies receive a so-called productio key for writig o media. It is used for programmig the media i the first place. For the daily use at the ed customer's, the productio key is the exchaged agaist the applicatio key. Each applicatio o a medium has its ow productio key that is replaced by its idividual applicatio key durig the exchage. The exchage ca also be made o a termial. The fuctio "Exchage productio key agaist istallatio key" is disabled after a cold start. If you wat to use it, eable it by meas of a data record. GID DID ON/OFF T t A Group address Device address Operatig mode Record type Record type modificatio Idetificatio see the followig table. Idetificatio Meaig 4 Disable exchagig productio key agaist applicatio key. 5 Eable exchagig productio key agaist applicatio key. B-Cliet PDC /

198 Pos: 36 @ 1 Kaba Mifare proximity reader Maual Reportig exchage of productio key agaist applicatio key Trasfer directio: Termial computer Fuctio The followig data record is set after exchagig the productio key agaist the applicatio key o a Kaba Mifare medium for a applicatio. It cotais: Cotets of the medium accordig to the parameterizatio of the A02 record UID of the Kaba Mifare medium Applicatio desigatio for which the productio key has bee exchaged. Possible values: - IDENTIFICATION GID Group address DID Device address ON/OFF Operatig mode f Record type $ Record type modificatio CI Clock idetificatio Y Y M Date M D D h h Time m m (s) Secods oly if set as parameter (s) 0 Reserved Media cotets accordig. to parameters; variable legth. 20 digits for UID of the master. 14 digits of the applicatio descriptio /2013 B-Cliet PDC6

199 Maual Tables Pos: 37 /KABA Kapitel (SW)/PDC6 Module/Tabelle Tables 5.1 Record types/record type modificatio for data records host termial Group RT RTM Meaig Chapter Display records Dialog records Termial cotrol Data record for ART D 0 Static display D 1 Dyamic display Authorized D 2 Dyamic display Not authorized 3.2 G 0 Dialog mask G 9 Ed of dialog I 0 Release bookigs I 1 Block bookigs I 2 Release local parameter settig I 3 Block local parameter settig I 6 Release dialog I 7 Block dialog J 0 Activate relay statically J 1 Activate relay dyamically J 2 Reset relay T 0 Switch termial to Olie state T 1 Switch termial to Offlie state T 2 Switch termial to Autoomous state T 3 Request recordig data i the Autoomous operatig mode T 4 Request termial state T 8 Request program o T A Restart termial applicatio T A Start service mode T t + Idetificatio T: Request reader iformatio T t + Idetificatio B0/B1: Request backup state T t + Idetificatio S0-S7: Istallatio key dowload T t + Idetificatio D0-D7: Delete istallatio keys idividually T t + Idetificatio A1: Delete all istallatio keys T t + Idetificatio A2: Disable the istallatio key applicatio T t + Idetificatio A3: Eable istallatio key applicatio T t + Idetificatio A4: Disable istallatio key exchage T t + Idetificatio A5: Eable istallatio key exchage 3.1 B-Cliet PDC /

200 Tables Maual Group RT RTM Meaig Chapter Buffer cotrol Logical bookig respose M 0 Read buffer M 1 Delete buffer M 2 Iitialize buffer R 0 Silet cofirmatio R 1 Bookig authorized R 2 Bookig ot authorized R 3 Repeat iput R 4 R 5 R 6 R4 to R6 record with differet umber of the displayed characters i the display ifo R 9 Prologatio of the respose time-out 3.5 Date/time U 0 Set date/time without sec. 3.6 U 1 Set date/time with secods Master records 3.7 Y 0 Idiv./pseudo master record dowload ad Y 1 Delete idiv./pseudo master record ad Y 8 Request idiv./pseudo master record ad Parameter up/dowload Y 9 Ed of idiv./pseudo master record dowload ad > 3 Dowload record parameter > 8 Parameter upload request > 9 Ed of parameter dowload /2013 B-Cliet PDC6

201 Maual Tables 5.2 Record types/record type modificatio for data records termial - host Group RT RTM Meaig Chapter Recordig data B 0 Query B 1 I or I with reaso B 2 Out or Out with reaso B 3 Official absece B 4 Ed of official absece B 5 Official absece Out B 6 Correctio B E Start of break B S Ed of break B # Record type modificatios for automatic i/out B $ detectio F A.. Productio data F z Dialog records 3.2 G 1 Dialog iput G 8 Dialog request G 9 Ed of dialog Error records O 1 Record cotets icorrect O 2 Commad caot be executed at the momet O 3 Commad o-executable 3.10 O 5 No licese Status records 3.11 H 1 Report o request H 2 Report after chage S 0 Buffer memory empty S 2 Buffer memory full S 3 Biometrics maagemet started S 4 Biometrics maagemet stopped S 7 Report termial status S V Report program o S t + Idetificatio B0: Report backup state S t + Idetificatio T: Report reader state B-Cliet PDC /

202 Tables Maual Group RT RTM Meaig Chapter Status records for ART Master records Parameter up-/dowload S t + Idetificatio S0-S7: Result of istallatio key dowload S t + Idetificatio D0-D7: Result of idividual istallatio key deletio S t + Idetificatio A1: Result of deletio of all istallatio keys S t + Idetificatio B1: Distributig istallatio keys with checksum report S t + Idetificatio B2: Distributig istallatio key with paret ifo report f $ Report applicatio key exchage Y 0 Id.-/pseudo master record upload ad Y 9 Ed of id.-/pseudo master record upload > 3 Parameter upload record > 9 Ed of parameter upload /2013 B-Cliet PDC6

203 Maual Tables 5.3 Table of block idetificatios BI Meaig Chapter B01. B15 b01. b15 D01. D25 d01. d25 Mailbox texts Mailbox texts with laguage idetificatio Dialog texts Dialog texts with laguage idetificatio E01 Stadard/daylight savig time switchover ad secods i data records F01. F15 G01. G15 I01. I10 i01. i10 L01. L04 M00. M15 m00. m15 Fuctio key fuctios Limit value pairs 2.16 Display ifo texts Display ifo texts with laguage idetificatio Special day table 2.22 Fuctio key texts Fuctio key texts with laguage idetificatio MA1 MA2 MA3 ma1 ma2 ma3 Tab texts Tab texts with laguage idetificatio B-Cliet PDC /

204 Tables Maual BI Meaig Chapter N00. N List texts List texts with laguage idetificatio P01 Fuctio key parameters (F01 to F15) P10. PFE PFF S01 T26. T30 t26. t30 T31. T53 T73. T80 t31. t53 t73. t80 W01. W20 X01 Time profiles 2.21 Reserved Buffer backup, logical group- ad device address ad respose time-out Fix texts Fix texts with laguage idetificatio Geeral texts Geeral texts with laguage idetificatio Lists 2.18 Display time authorized, display time ot authorized, operatio time relay 1 ad 2, operator time-out ad display time display ifo X02 PIN for biometrics maagemet X07 Character set idetificatio 5.13 Y10. Y17 Duplicatio fields 2.17 Z01 Fuctio key cotrol 2.19 Z11 Z12 Z13 Relay cotrol /2013 B-Cliet PDC6

205 Maual Tables 5.4 Table of clock idetificatios Idetificatio i data record Time valid Data record with secods Idetificatio for user laguage Cause 0 No No No Time ot set 1 Yes No No Time set without secods 2 No Yes No Time ot set 3 Yes Yes No Time set with secods 4 No No Yes Time ot set 5 Yes No Yes Time set without secods 6 No Yes Yes Time ot set 7 Yes Yes Yes Time set with secods 5.5 Table of parameter settig errors Error idetificatio 4 Meaig Less digits were read from the badge tha defied with the sigle fuctio block parameter From digit, see chapter ). 5 A master record refers to a time profile which is ot stored i the termial. 6 Iteral error. Please keep the cofiguratio ad cotact the maufacturer. 7 L The parameter Idividual master record required (see chapter ) defies, that each ID o. read from the badge must be assiged to a master record. The ID o. idetificatio is ot set i the Limit value o. parameter of ay sigle fuctio block, see chapter ). A fuctio for which o licese is available has bee addressed durig the bookig sequece. B-Cliet PDC /

206 Tables Maual 5.6 Table of error idetificatios Error idetificatio Meaig 0 No error/data uchecked 1 Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o Data out of limit value pair o. 09 : Data out of limit value pair o. 10 ; Data out of limit value pair o. 11 < Data out of limit value pair o. 12 = Data out of limit value pair o. 13 > Data out of limit value pair o. 14? Data out of limit value pair o. 15 C D E J K L M N O Versio umber wrog No master record foud PIN wrog or missig No official absece authorizatio No correctio authorizatio I/Out error (plausibility error) Master record blocked No time authorizatio (profile) No authorizatio for badge umber iput /2013 B-Cliet PDC6

207 Maual Tables 5.7 Table of laguage idetificatios The laguage idetificatio cosists of 6 digits: digit 1 ad 2 represet the laguage digit 3 ad 4 represet the coutry digit 5 ad 6 are ot importat at the momet ad must be fille with blaks (20hex) If o coutry idetificatio is eeded, the digits 3 ad 4 may also be filled up with blaks. If a laguage is switched durig operatio, the characters are represeted by meas of the curretly set character set. See settigs i the sectio [RegioalSettigs] i the systems.ii file, chapter 6.1. Laguage idetificatio Meaig Character set used da Daish ISO (Lati 1) de Germa e Eglish es Spaish fr Frech it Italia l Dutch o Norwegia sv Swedish cs Czech ISO (Lati 2) hr Croatia hu Hugaria pl Polish ro Romaia sk Slovak sl Sloveia bg Bulgaria ISO (Cyrillic) be Bielorussia ru Russia sr Serbia uk Ukraiia el Greek ISO (Moder Greek) ar Arabic JKabaArabic ja Japaese JKabaJapaese th Thai JKabaThai zh Chiese JKabaChiese B-Cliet PDC /

208 Tables Maual Coutry idetificatio GB US Meaig Great Britai USA The differetiatio betwee coutries offers the beefit, for example that "e" ca be separated for the coutries "GB" ad "USA". This allows to defie differet texts for the UK ad USA, these texts ca cotai coutry-specific terms /2013 B-Cliet PDC6

209 Maual Tables 5.8 Table of characters accordig to ISO If o character set has bee chose or character set 000 USA ASCII has bee set (see chapter 5.13) the 8-bit characters ca be used. To use multiligualism, it is absolutely ecessary. The tables below show the way the user iformatio ad texts are displayed ISO (Lati 1) x 0x 1x 2x 3x 4x 5x 6x 7x 8x 9x Ax Bx Cx Dx Ex Fx 0 SPACE P ` p NO SP À Ð à ð 1! 1 A Q a q ± Á Ñ á ñ 2 " 2 B R b r 2 Â Ò â ò 3 # 3 C S c s 3 Ã Ó ã ó 4 $ 4 D T d t Ä Ô ä ô 5 % 5 E U e u μ Å Õ å õ 6 & 6 F V f v 0 Ö 0 ö 7 ' 7 G W g w Ç ç 8 ( 8 H X h x È 0 è 0 9 ) 9 I Y i y 1 É Ù é ù A * : J Z j z ª º Ê Ú ê ú B + ; K [ k { Ë Û ë û C, < L \ l ¼ Ì Ü ì ü D - = M ] m } ½ Í Ý í ý E. > N ^ ~ ¾ Î Þ î þ F /? O _ o DEL Ï ß ï ÿ B-Cliet PDC /

210 Tables Maual ISO (Lati 2) x 0x 1x 2x 3x 4x 5x 6x 7x 8x 9x Ax Bx Cx Dx Ex Fx 0 SPACE P ` p º Ŕ Đ ŕ đ 1! 1 A Q a q Ą ą Á Ń á ń 2 " 2 B R b r, Â Ň â ň 3 # 3 C S c s Ł ł Ă Ó ă ó 4 $ 4 D T d t Ä Ô ä ô 5 % 5 E U e u Ľ ľ Ĺ Ő ĺ ő 6 & 6 F V f v Ś ś Ć Ö ć ö 7 ' 7 G W g w Ç ç 8 ( 8 H X h x Č Ř č ř 9 ) 9 I Y i y Š š É Ů é ů A * : J Z j z Ş ş Ę Ú ę ú B + ; K [ k { Ť ť Ë Ű ë ű C, < L \ l Ź ź Ĕ Ü ĕ ü D - = M ] m } Í Ý í ý E. > N ^ ~ Ž ž Î Ţ î ţ F /? O _ o DEL Ż ż Ď ß ď /2013 B-Cliet PDC6

211 Maual Tables ISO (Cyrillic) x 0x 1x 2x 3x 4x 5x 6x 7x 8x 9x Ax Bx Cx Dx Ex Fx 0 SPACE P ` p А Р а р 1! 1 A Q a q Ё Б С б с ё 2 " 2 B R b r Ђ В Т в т ђ 3 # 3 C S c s Ѓ Г г У ѓ 4 $ 4 D T d t Є Д Ф д ф є 5 % 5 E U e u Ѕ Е Х е х ѕ 6 & 6 F V f v І Ж Ц ж ц і 7 ' 7 G W g w Ϊ З Ч з ц ї 8 ( 8 H X h x Ј И Ш и ш ј 9 ) 9 I Y i y Љ Й Щ й щ љ A * : J Z j z Њ К Ъ к ъ њ B + ; K [ k { Ћ Л Ы л ы ћ C, < L \ l Ќ М Ь м ь ќ D - = M ] m } ˉ Н Э н э E. > N ^ ~ Ў О Ю о ю ў F /? O _ o DEL Џ П Я п я џ B-Cliet PDC /

212 Tables Maual ISO (Moder Greek) x 0x 1x 2x 3x 4x 5x 6x 7x 8x 9x Ax Bx Cx Dx Ex Fx 0 SPACE P ` p ΐ Π ΰ π 1! 1 A Q a q ` ± Α Ρ α ρ 2 " 2 B R b r ² Β β ς 3 # 3 C S c s ³ Γ Σ γ σ 4 $ 4 D T d t Δ Τ δ τ 5 % 5 E U e u Ε Υ ε υ 6 & 6 F V f v Ά Ζ Φ ζ φ 7 ' 7 G W g w Η Χ η χ 8 ( 8 H X h x Έ Θ Ψ θ ψ 9 ) 9 I Y i y Ή Ι Ω ι ω A * : J Z j z Ί Κ Ϊ κ ϊ B + ; K [ k { Λ Ϋ λ ϋ C, < L \ l Ό Μ ά μ ό D - = M ] m } ½ Ν έ ν ύ E. > N ^ ~ Ύ Ξ ή ξ ώ F /? O _ o DEL Ώ Ο ί ο /2013 B-Cliet PDC6

213 Maual Tables 5.9 Table of characters Chiese The correspodig uicode is displayed above the character. Fig. 17: Chiese characters with uicode B-Cliet PDC /

214 Tables Maual 5.10 Table of characters Japaese The correspodig uicode is displayed above the character. Fig. 18: Japaese characters with uicode /2013 B-Cliet PDC6

215 Maual Tables Fig. 19: Japaese characters with uicode Special otes The fields marked i yellow cotai the Japaese characters. This icludes Kaji characters, i.e. there are also Chiese characters. Overall, 148 characters (Japaese ad Chiese) ca be displayed accordig to this fot table. B-Cliet PDC /

216 Tables Maual 5.11 Table of characters Thai The correspodig uicode is displayed above the character. Fig. 20: Thai characters with uicode /2013 B-Cliet PDC6

217 Maual Tables Special otes The fields marked i blue cotai the most importat characters ad the umeric values i Thai. The positio of these characters i this fot table correspods to the positio i the ISO character set. The correspodig uicode value is idicated for each character. I Thai, so-called combied characters exist. As the software is ot able to geerate these combiatios by itself, some predefied combiig characters were itegrated. These are displayed i the yellow fields. The combiig characters comprise up to 3 idividual characters. Above the respective combiig character, all the uicodes used are show, whereas the first uicode value represets the correspodig mai character. B-Cliet PDC /

218 Tables Maual 5.12 Table of characters Arabic The correspodig uicode is displayed above the character. Fig. 21: Arabic characters with uicode /2013 B-Cliet PDC6