Alarms & Remote Start

Transcription

1 larms & Remote Start INSTLL GUIDE OEM-L(RS)-VW-[OL-MD-LL]-EN DOCUMENT NUMER 897 REVISION DTE 008 FIRMWRE OEM-L(RS)-VW-[OL-MD-LL] HRDWRE OL-MD-LL CCESSORIES OL-LODER (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. EFORE INSTLLTION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately) utomotive Data Solutions Inc. 0

2 VEHICLE LIST - OF PGE OF DOC.: # FETURES NOTE Warning: Install type supports idle mode. Install type does NOT support idle mode. MKE MODEL I YER INSTLL TYPE SECURE TKEOVER X LOCK STRT/STNDLONE MOD. RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK TRUNK/HTCH RELESE DOOR STTUS OUTPUT TRUNK STTUS OUTPUT HOOD STTUS OUTPUT* UTOLIGHT CTRL TCHOMETER OUTPUT RKE PEDL STTUS OUTPUT E-RKE OUTPUT Keyport with PTS T 08- Keyport without PTS T 08- llroad Keyport with PTS T 08- llroad Keyport without PTS T 08- Keyport with PTS T 08- Keyport without PTS T 08- Q Keyport with PTS T 09- Q Keyport without PTS T 09- Q TDI Keyport with PTS T 09- Q TDI Keyport without PTS T 09- RS Keyport with PTS T 08- RS Keyport without PTS T 08- S Keyport with PTS T 08- S Keyport without PTS T 08- S Keyport with PTS T 08- S Keyport without PTS T 08- SQ Keyport with PTS T 09- SQ Keyport without PTS T 09- *vailable only if vehicle is equipped with factory hood switch. UDI utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

3 OX CONTENTS - OF PGE OF DOC.: # OX CONTENTS MODULE PIN WHITE CONNECTOR PIN LCK CONNECTOR WHITE PROGRMMING UTTON LED 7 PIN WHITE CONNECTOR 0 PIN LCK CONNECTOR WHITE WHITE 7 C F LCK PIN WHITE CONNECTOR DT CLE LUE D E LCK DT PORT (WELINK, RF, TELEMTIC) PIN LUE CONNECTOR DT CLE WELINK CLE (required accessory sold separately) WELINK CLE MODULE DT PORT COMPUTER US PORT PIN LCK CLE utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

4 TECHNICL NOTE - OF PGE OF DOC.: # IMPORTNT STRTER WIRE CONNECTION FOR VEHICLES WITH UTOMTIC TRNSMISSION. lack connector at brake switch under the dashboard, near the brake pedal. t the ECU under the wiper cowl, located under the hood, in the engine compartement. (IF PRESENT) OR RED/LCK RKE (+) RED/LCK RKE (+) STRTER (+) FROM RS STRTER (+) FROM RS utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

5 TYPE - WIRE CHRT - OF PGE OF DOC.: # MKE MODEL YER WIRE DESCRIPTION CONNECTOR NME CONNECTOR COLOR CONNECTOR TYPE POSITION UDI WIRE COLOR POLRITY MODULE LOCTION COMPONENT LOCTOR Keyport with PTS T llroad Keyport with PTS T S Keyport with PTS T Keyport with PTS T RS Keyport with PTS T S Keyport with PTS T Q Keyport with PTS T Q TDI Keyport with PTS T SQ Keyport with PTS T V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ 0 pin 0 lue/yellow (-) Push-button ~ PTS ~ ~ 0 pin 0 lue/white (-) Push-button ~ Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ 0 pin 0 lue/yellow (-) Push-button ~ PTS ~ ~ 0 pin 0 lue/white (-) Push-button ~ Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ 0 pin 0 lue/yellow (-) Push-button ~ PTS ~ ~ 0 pin 0 lue/white (-) Push-button ~ Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

6 TYPE - WIRING DIGRM - OF PGE OF DOC.: # MODULE PTS PTS SWITCH F C D E DT PTS (-) - 0 PTS (-) - 0 C D E 7 0 GRY/YELLOW (NC) 0 GRY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED - PTS (-) OUTPUT 0 LUE/YELLOW (NC) 0 LUE/RED (NC) 0 PINK - IGNITION (+) INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - KEYSENSE (-) OUTPUT 0 ORNGE/LCK - PTS (-) OUTPUT 0 ROWN/YELLOW - CNL 07 ROWN/RED - CNH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) 0 WHITE - V (+) CONSTNT 0 WHITE/RED (NC) 0 WHITE/LCK 0 LUE/WHITE (NC) 0 WHITE (NC) 0 LCK - GROUND 0 RED - V (+) WITHOUT COMPTILE CCESSORY 8 N00 DIODE CNL CNH IGNITION (+) V (+) RKE (+) - 0 TWISTED WIRES IN DOOR HRNESS IN DRIVER KICK PNEL REMOVE TTERY EHIND FUSE OX RKE SWITCH F DT CLE COMPTILE CCESSORY 0 GREEN/LCK- HOOD STTUS (-) INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) 0 ROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/LCK (NC) 07 WHITE (NC) 08 LCK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) OR WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS. 7. WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH V (+) KEYSENSE (-) LOOPS (0 WG) ROUND KEYFO 0 LOOPS (0 WG) ROUND KEYPORT KEYPORT - CONNECTOR EHIND KEYPORT TWO KEYS RE REQUIRED FOR THIS INSTLLTION. ONE KEY WILL REMIN PERMNENTLY IN THE VEHICLE. THE OTHER KEY WILL E USED FOR THE PROGRMMING PROCEDURE. IT WILL THEN E RETURNED TO THE OWNER. FTERMRKET HOOD SWITCH (-) utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

7 TYPE - WIRE CHRT - OF PGE 7 OF DOC.: # MKE MODEL YER WIRE DESCRIPTION CONNECTOR NME CONNECTOR COLOR CONNECTOR TYPE POSITION UDI WIRE COLOR POLRITY MODULE LOCTION COMPONENT LOCTOR Keyport without PTS T llroad Keyport without PTS T S Keyport without PTS T Keyport without PTS T RS Keyport without PTS T S Keyport without PTS T Q Keyport without PTS T Q TDI Keyport without PTS T SQ Keyport without PTS T V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ pin 0 lack (-) ehind keyport ~ PTS ~ ~ pin lack/red (-) ehind keyport ~ PTS ~ ~ pin Gray/lue (-) ehind keyport Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ pin 0 lack (-) ehind keyport ~ PTS ~ ~ pin lack/red (-) ehind keyport ~ PTS ~ ~ pin Gray/lue (-) ehind keyport Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ V ~ ~ ~ ~ Red/lack (+) ehind fuse box ~ rake ~ ~ 0 pin 0 Red/lack (+) t brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DT) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/rown (DT) Twisted wires in door harness in driver kick panel ~ Ignition ~ ~ ~ ~ lack (+) ehind fusebox ~ PTS ~ ~ pin 0 lack (-) ehind keyport ~ PTS ~ ~ pin lack/red (-) ehind keyport ~ PTS ~ ~ pin Gray/lue (-) ehind keyport Keysense ~ ~ pin 0 lack/yellow (-) ehind keyport ~ utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

8 TYPE - WIRING DIGRM - OF PGE 8 OF DOC.: # MODULE F C D E DT CNL CNH IGNITION (+) V (+) TWISTED WIRES IN DOOR HRNESS IN DRIVER KICK PNEL EHIND FUSE OX 0 GRY/YELLOW (NC) 0 GRY/RED - PTS (-) OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - PTS (-) OUTPUT 0 LUE/YELLOW (NC) 0 LUE/RED (NC) N00 DIODE RKE (+) - 0 RKE SWITCH 7 0 PINK - IGNITION (+) INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - KEYSENSE (-) OUTPUT 0 ORNGE/LCK - PTS (-) OUTPUT 0 ROWN/YELLOW - CNL 07 ROWN/RED - CNH C 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) D E 0 WHITE - V (+) CONSTNT 0 WHITE/RED (NC) 0 WHITE/LCK 0 0 LOOPS (0 WG) ROUND KEYFO REMOVE TTERY KEYPORT 0 LUE/WHITE (NC) 0 WHITE (NC) 0 LCK - GROUND 0 RED - V (+) WITHOUT COMPTILE CCESSORY OR DT CLE COMPTILE CCESSORY WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS. 7. V (+) 0 LOOPS (0 WG) ROUND KEYPORT F GREEN/LCK- HOOD STTUS (-) INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) 0 ROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/LCK (NC) 07 WHITE (NC) 08 LCK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) WITHOUT OEM HOOD SWITCH: INSTLL ND CONNECT TO FTERMRKET HOOD SWITCH PTS (-) - PTS (-) - PTS (-) - 0 KEYSENSE (-) CONNECTOR EHIND KEYPORT TWO KEYS RE REQUIRED FOR THIS INSTLLTION. ONE KEY WILL REMIN PERMNENTLY IN THE VEHICLE. THE OTHER KEY WILL E USED FOR THE PROGRMMING PROCEDURE. IT WILL THEN E RETURNED TO THE OWNER. FTERMRKET HOOD SWITCH (-) utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

9 MODULE PROGRMMING PROCEDURE - OF PGE 9 OF DOC.: # STOP CC ON STRT Push start button twice [x] to ON position. ENGINE STRT STOP 0 Wait, LED will turn solid GREEN then will turn OFF. 0 STOP CC ON STRT Push start button once [x] to OFF position. ENGINE STRT STOP 0 Module Programming Procedure completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

10 VLET MODE PROGRMMING PROCEDURE - OF PGE 0 OF DOC.: # >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within 7 seconds. 0 OFF CC ON STRT Cycle ignition ON five times [x OFF/ON] rapidly. ENGINE STRT STOP 0 Wait, LED will turn solid RED for seconds. 0 OFF CC ON STRT Set ignition to OFF position. ENGINE STRT STOP 0 Valet Mode Programming Procedure completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

11 PGE OF DOC.: # MODULE NVIGTION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to OFF position. 07 TO CCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously OFF CC ON STRT TO CCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO CCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MNDTORY: EXIT MODULE NVIGTION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STRT STOP 0 0 [X] utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

12 MODULE NVIGTION CHRT - OF PGE OF DOC.: # MODULE NVIGTION CHRT: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISRM/UNLOCK EFORE STRT 0 OFF 0 ON 0 RELOCK FTER STRT 0 OFF 0 ON 0 RELOCK FTER SHUTDOWN 0 OFF 0 ON 0 FORCE UNLOCK LL ON FIRST PRESS 0 OFF 0 ON 0 N/ 0 N/ 0 N/ 0 N/ 0 DISLE 07 FCTORY KEYLESS RS SEQUENCE 0 N/ 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 CONFIGURTION 0 0 MIN 0 0 MIN 08 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 09 WIT TO STRT DELY 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0- N/ 0 N/ 0-07 Technical Support only 0 N/ 0 N/ utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

13 REMOTE STRTER ERROR CODES - OF PGE OF DOC.: # REMOTE STRTER ERROR CODES: NOTES [X] NUMER OF PRKING LIGHT FLSHES DIGNOSTIC I II WRNING: The following applies only when the parking lights are connected and supported by the system. fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

14 MODULE DIGNOSTICS - OF PGE OF DOC.: # TEST MODULE LED STTUS DIGNOSTIC I II III DURING PROGRMMING DURING REMOTE STRT WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. dditional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

15 MODULE RESET PROCEDURE - OF PGE OF DOC.: # Disconnect all connectors from module except the LCK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the LCK -PIN connector. 08 Repeat programming procedure. 0 PRESS ND HOLD programming button while connecting the LCK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELESE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN

16 INSTLLTION CHECKLIST - OF PGE OF DOC.: # CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. Installation checklist completed. utomotive Data Solutions Inc. 0 OEM-L(RS)-VW-[OL-MD-LL]-EN