1 awea.com.m y

Transcription

1 1 y

2 2 y

3 Announcement (1.0) (1.1) LUM END of Support The support of LUM licensing technology was end on December 31 st This technology had been replaced by DSLS which is already available in all V5 release since V5R21, and in all V6 releases. (1.2) Win XP & Win Vista END of Support End of support of V5 and V6 on Windows XP and Windows Vista on April 8 th (1.3) Windows Operating System Prerequisites License Server DSLS Win Server 2008 R2 64- bit Win Server 2008 R2 SP1 64-bit Operating System Win XP, SP3, 32- bit Win XP, SP2, 64- bit Win 7 64-bit Win 7 SP1 64-bit DSLS 2012 DSLS 2013x DSLS Supported CATIA Release V5R19 V5R20 V5R21 V5-6R2012 V5-6R2013 DSLS 2012 DSLS 2013x Client Workstation CATIA Release V5R19, V5R20, V5R21 V5-6R2012 Operating System Win XP 32-bit Win XP 64-bit Win 7 32-bit Win 7 64-bit Win 8 V5-6R2013 Remarks: i. 4 GB of RAM are recommended ii. CATIA V5 will not work on a virtual machine 3 y

4 Product Sharing (2.0) (2.1) Introduction SIMULIA provides complete design-integrated simulation capabilities within the CATIA V5 design environment. Designers can use the familiar CATIA user interface to perform analysis directly on their master reference model in CATIA. Data integrity issues are avoided since there is no transfer and translation of geometry. The combined CATIA Analysis and the SIMULIA Extended Analysis product suites have been developed for designers and engineers who need to accurately size their designs and quickly evaluate their real world performance during the design phase. (2.2) CATIA V5 Analysis Key Technologies 1. Octree automatic solid mesher. 2. Smart adaptive meshing. 3. Automatic geometry simplification. 4. Incompatible mesh assembly. 5. Simulation of mechanical hybrid assemblies. 6. Associative weld FE modeling. 7. Associative vehicle-level FE modeling Bit Analysis. 9. 3DXML Viewer. (2.3) CATIA V5 Analysis Product Portfolio GPS Generative stress & modal analysis of single parts. Calculate displacement & stress for volume, surface & wireframe geometries. GAS Generative stress modal analysis of hybrid assemblies including accurate representation of the way parts interact & connected. EST Advanced options for pre/post-processing and solving include multiple static analysis cases, frequency & buckling analysis. 4 y

5 GDY Generative structural dynamic response for both transient & harmonic analysis to prevent resonance & other dynamic effects. FMS Advanced options for complex wireframe & surface meshing where by the meshes generated are fully associative. FMD Advanced options for complex solid meshing where by the meshes generated are fully associative. (2.4) SIMULIA Extended Analysis Product Portfolio ATH Understand transient temperature distribution in response to direct heating & specified the conductivity for parts in assemblies. ANL Non Linear effect such as for plastics & rubber. Large displacement & advanced contact capability due to geometric proximity. Product Sharing RBM Rule Based Meshing (RBM) extends the capabilities of FMS to enable automated and higher quality surface meshing for all workflows that use CATIA meshing tools. 5 y

6 CATIA Administration (3.0) (3.1) Customize own TOOLBAR and ICON If you wish to run a macro in your preferred environment, you can customize your own toolbar and icon. STEPS 1. Go to Tools --- Customize. 2. Go to Toolbars tab, select standard then click on New. CATIA ANALYSIS PRODUCT PORTFOLIO: 3. Rename the new Toolbar Name. For example: Macro Generation y

7 4. Then the new toolbar will pop out in the CATIA environment. Click OK to proceed. 5. Go to Tools --- Customize again to create new icon. Select the tab named Commands, click on All Commands. 6. Select the necessary command in the list, example: Macros. Then click on Show Properties. 7 y

8 7. Select Icon, choose the icon from the Icons Browser. After select the icon, click close. 8. Drag and drop the icon to the new toolbar that created previously. Drag Drop 9. Click on the new icon to perform macro generation. 8 y

9 (3.2) Load CATIA Assemblies in VISUALIZATION Mode i. Reduce assembly file loading duration ii. Generate CGR file for visualization purpose STEPS 1. Go to Tools --- Options, select Product Structure under Infrastructure. Check the Work with the cache system in Cache Management tab. 2. Restart Catia application after the configuration 3. Load the Catia assembly file, a message will pop out at the bottom which shown loading and cache creation in progress. 9 y

10 4. The difference of the Design Specification Tree between Design and Visualization mode. Design mode Visualization mode 5. Other cache system options include the following: A. The Path to the local cache column defines the directory in which the CGR files are stored. B. Released caches are read-only areas where CATIA searches for existing CGR files. These are defined in the Path to the released cache column. C. The Cache Size section defines the maximum cache size. Once the limit is reached, CGR files are deleted based on the first-in first-out rule. D. The Timestamp section saves the CGR files with a timestamp and checks whether the model has been modified since the last CGR file was created. If so, it gets updated with the latest version. A B D C 6. The representation of Catia Assembly in visualization mode produce external appearance of the components only y

11 Remarks: The components do not contain any technical information. In the specification tree, the individual nodes for the components are not displayed. In the geometry area, when you place your pointer over a component you will notice that the it is tessellated. As a result, you will not be able to highlight or select its individual features. 7. To activate the component from Visualization mode to Design mode - Double click on the component or select Design Mode under Representations to edit the components. 8. To return to the Visualization mode, right click the component and click Representations > Visualization Mode Remarks: You can return that component to Visualization mode only if NO changes have been made. If changes have been made, a new CGR file needs to be created. You have to save and reopen the entire assembly y

12 Licensing (4.0) (4.1) Network License Configuration (a) To set up Catia license server using Dassault Systèmes License Server (DSLS). (b) To set up Catia license client using Dassault Systèmes License Server (DSLS). STEPS License Server Configuration: 1. Go to Start > All Programs > DS License Server > License Server Administration 2. Open DSLS license administration tool > Go to Server Definitions tab > Right click in the blank box > choose Add new server 3. License Server Connection Parameters will pop up > Insert License server name (computer hostname). Example: server1 4. Server will add to Server Definitions. Double click to open the new window for license server 12 y

13 5. Double click on the license server. Remarks: Keep the defaults setting (none) if no administration authorization is required. If the client machine is required to monitor or observe the license status, CHECK the full box 6. The information of the server will appear after click OK y

14 7. Create a new folder named Licenses in the location path below: For Windows 7 or Vista: C:\Program Data\Dassaultsystemes\LicenseServer For Windows XP: C:\Documents and Settings\All Users\Application Data\DassaultSystemes\LicenseServer 8. Create a text file named DSLicSrv.txt in the Licenses folder created previously. 9. Open the created text file i.e. DSLicSrv and fill up the information like Host Name or IP address of the License server and port number (4085). Example: : y

15 10. Copy and paste the license file (.LICZ) in the same Licenses folder which you have received. 11. Go to License > Enroll 12. Dialog box appear. Retrieve the license (.LICZ) file from the License folder location. Go to the directory where the license is saved > Select License > Click Open 13. Dialog box for license enrollment appear > Click OK after finish. 14. Go to License Administration Tab > Check the server1 box 15 y

16 License Client Configuration 1. Create a new folder named Licenses in the location path below: For Windows XP: C:\Documents and Settings\All Users\Application Data\DassaultSystemes For Windows 7 or Vista: C:\ProgramData\DassaultSystemes\ 2. Create text files as shown below and name it as DSLicSrv.txt in the location mentioned above. 3. Same as the previous setting in License Server, we need to create a text file named DSLicSrv.txt in the above mentioned location. 4. Once the text file created open the text file and put in information like the server Hostname or IP address > save the text file. Example: server1: y

17 (4.2) Nodelock License Configuration Method to install DSLS nodelock license STEPS 1. Create a new folder named Licenses in the location path below: For Windows XP: C:\Documents and Settings\All Users\Application Data\DassaultSystemes For Windows 7 or Vista: C:\ProgramData\DassaultSystemes\ 2. Insert the DSLS license file (.LICZ) in the Licenses folder. 3. Go to Start > All Programs > CATIA > Nodelock Key Mangement (DSLS) V5R21 and onwards. License will automatically enroll y

18 (4.3) Method to Implement DSLS Offline Configuration i. Extract license for your mobile workstation ii. Maximum duration: 30 days STEPS 1. Go to Start --- All Programs --- CATIA --- Tools --- Nodelock Key Management (DSLS) V5R21and onwards. 2. Select the second tab which is the Offline Management 3. Right click on the license, example: AL2 and select Extract y

19 4. Drag your mouse to the duration required (Maximum period: 30 days) and click OK. 5. If you required restituting the license to license server before the expiry date, right click on the license and select Restitute y

20 CATIA Feature Applications (5.0) (5.1) Create TEXT in 3D for embossing This will allow user to create 3D text profile in CATIA environment. STEPS 1. Open a Drawing file. 2. Create the Text with the desired font type and font size. Example here we choose Times New Roman for the font type and size of 20mm and 13mm. 3. Save the drawing file as.dxf file. 4. Open the DXF file. 5. Select the whole Text using the Trap Selection. 6. Right click and choose Copy. 7. Go to the Part file where you wish to create the text y

21 8. Select the Sketch icon and select the face where you want to place the Text. New sketch will be created. 9. Right click and choose Paste. 10. The text will be pasted. 11. You may use the text for both Emboss and Engrave purposes y

22 (5.2) Create CONTOUR Contour create a closed contour geometry from a set of curves on surface Remarks: i. Only available for HD2, CAC+MCE+HDX or any GSD license holder. ii. Release V5R21 onwards SCENARIO Fail to split surface with a set of open curves STEPS 1. Click Contour in the wireframe toolbar. The Contour Definition dialog box appears y

23 2. Select the respective surface. 3. Select curves to form a closed boundary. 4. Set the value of the Extrapolation Distance. Once the closed contour is formed, the resultant contour is highlighted in blue color. 5. Click OK to create the contour. The element (identified as Contour.xxx) is added to the specification tree. 6. Split the surface with the closed contour wireframe y

24 (5.3) Enhancement to SWEEP Generate swept surfaces that have a twisted area by delimiting the portions of the swept surface to be kept. Remarks: i. Only available for HD2, CAC+MCE+HDX or any GSD license holder. ii. Release V5R21 onwards STEPS 1. Sweep failure due to there are two discontinuities in tangency on the input guide 2. New Compute CO vertices as twisted areas option are added to the Sweep functionality to remove or fill the CO vertices area automatically. 3. To construct sweep surface with guide curve and reference surface, Linear Sweep is applied. Reference surface Guide curve 24 y

25 4. By default, the check box for Compute CO vertices as twisted areas is checked and linear sweep can be constructed directly. with uncheck the Remove Cutters on Preview and Fill twisted areas: Remarks: Useful for manual editing on the surfaces with ALL options checked Remarks: Fine tune on the Setback % for different distance of twisted areas Setback % 25 y

26 (5.4) Create Curve Using Equation in CATIA V5 Remarks: Only available for HD2, CAC+MCE+HDX or any GSD license holder. Equation: Y=A*exp (-x*d)*sin (cycle*pi*x*1 rad) + Distance A, Amplitude: 20 D, Damping : 4 Cycle: 20 Distance : 30 STEPS 1. Insert parameters in the Catia using Formula follow the sequences as below Click OK after that. Repeat the same steps for the rest of the parameters: Damping, Cycle and Distance y

27 3. Insert the equation using Law Editor,. 4. Insert the information as below: 5. Type in the equation in the left side path. Specific math function can be obtained under the Dictionary, Members of Parameters and Members of All. (i.e: exponential, sin, PI) 27 y

28 6. Go to Generative Shape Design workbench, insert a line. (Y=0, Y=100) 7. Use Parallel Curve, insert the law created previously under advanced tab y

29 (5.5) Quick DELETE Patches Of Surface i. Edit the datum (geometry with no history) surface ii. Useful in surface healing operation 1. You may delete patches of surface from the main surface without the use of wireframe & split. 2. Select the Join icon. Select the main surface. Select the Sub-Elements To Remove tab. 3. Select the patches that you would like to delete from the main surface. Example: select the three patches shown. 4. Upon clicking OK, you will notice that the three patches was deleted from the main surface y

30 (5.6) Create A Simple Nonlinear Axis Spring Model Remarks: Only available for HD2, CAC+MCE+HDX or any GSD license holder. 1. You may use curve from either sketch or Spline. 2. Create another sketch at the same plane as the curve. Example: select the XY Plane. Create the Circle as shown y

31 3. Create an Extrude by using the curve as profile. Make sure the direction is normal to the sketch profile. 4. Create a Sweep Surface. Choose With Reference Surface. Profile : Circle Sketch. Guide Curve : Previous Non Linear curve. Surface : Previous Extrude y

32 5. Select the Law button beside the Angle tab. 6. Select the Linear for the Law type. Enter 0deg for start value. Enter 9200deg for End value. 7. Click OK for the sweep. Hide the Extrude surface. The result is the Spring profile with a Non Linear Axis y

33 Notes: 33 y

34 Notes: 34 y

35 35 y

36 36 y