Avigilon Control Center Client User Guide

Transcription

1 Avigiln Cntrl Center Client User Guide Versin: 4.12 Enterprise PDF-CLIENT-E-F-Rev2

2 Cpyright 2013 Avigiln. All rights reserved. The infrmatin presented is subject t change withut ntice. N cpying, distributin, publicatin, mdificatin, r incrpratin f this dcument, in whle r part, is permitted withut the express written permissin f Avigiln. In the event f any permitted cpying, distributin, publicatin, mdificatin, r incrpratin f this dcument, n changes in r deletin f authr attributin, trademark legend, r cpyright ntice shall be made. N part f this dcument may be reprduced, stred in a retrieval system, published, used fr cmmercial explitatin, r transmitted, in any frm by any means, electrnic, mechanical, phtcpying, recrding, r therwise, withut the express written permissin f Avigiln. Avigiln Tel Fax Revised

3 Table f Cntents Intrductin... 1 What is the Avigiln Cntrl Center Client?... 1 System Requirements... 1 Fr Mre Infrmatin... 2 Avigiln Training Center... 2 Supprt... 2 Upgrades... 2 Feedback... 3 Getting Started... 4 Starting and Shutting Dwn the Avigiln Cntrl Center Client... 4 Starting the Client Sftware... 4 Shutting Dwn the Client Sftware... 4 Discvering Servers... 5 Lgging Int and Out f Servers... 6 Lgging In... 7 Lgging Out... 8 Navigating the Applicatin... 8 Adding and Remving Cameras in a View Adding a Camera t a View Remving a Camera Frm a View Viewing Live and Recrded Vide Setup...12 Managing Server Cnnectins Discvering Servers Editing and Deleting a Server Cnnectin Cnnect/Discnnect Cameras Discvering a Camera iii

4 Avigiln Cntrl Center Enterprise Client User Guide Cnnecting a Camera t a Server Editing the Camera Cnnectin t the Server Failver Cnnectins Discnnecting a Camera frm a Server Upgrading Camera Firmware Server Setup Accessing the Server Setup General Recrding Schedule Recrding and Bandwidth Users and Grups Alarms Scheduled Backup POS Transactins Ntificatin Rules System Lg License Plate Recgnitin Scheduling Server Events Camera Setup Accessing the Camera Setup General Netwrk Image and Display Cmpressin and Image Rate Image Dimensins Mtin Detectin Privacy Znes Manual Recrding Digital Inputs and Outputs Micrphne Speaker Client Setup Accessing the Client Setup General iv

5 Table f Cntents Jystick Exprting Settings Imprt Settings Micrphne Site View...96 What is Site View? Accessing Site View Adding a Site Editing and Deleting a Site Views...99 What are Views? Adding and Remving a View Adding a New View t the Applicatin Windw Adding a View t a New Windw Clsing a View frm the Applicatin Windw Clsing a Windw View Layuts Selecting a Layut fr a View Editing a View Layut Making a View Full Screen Ending Full Screen Cycling Thrugh Views Saving a View Saving a View Opening a Saved View Renaming a Saved View Deleting a Saved View Maps Using a Map Adding a Map Editing and Deleting a Map Web Pages Using a Web Page Adding a Web Page Editing and Deleting a Web Page v

6 Avigiln Cntrl Center Enterprise Client User Guide Vide Mnitring Live Vide Adding and Remving Cameras in a View Displaying Live Vide Using Instant Replay Zming and Panning a Vide Mnitring PTZ Cameras Listening t Audi in a View Bradcasting Audi in a View Triggering Manual Recrding Triggering Digital Output Mnitring POS Transactins Mnitring Recrded Vide Adding and Remving Cameras in a View Displaying Recrded Vide Zming and Panning a Vide Listening t Audi in a View Playing Back Recrded Vide Bkmarking Recrded Vide Reviewing POS Transactins Adjusting Vide Display in Image Panels Maximizing an Image Panel Displaying Vide Overlays Changing the Image Panel Display Quality Settings Changing the Image Panel Display Adjustments Settings Displaying Analg Vide in Deinterlaced Mde Alarms Accessing the Alarms Tab Reviewing Alarms Reviewing Alarm Vide Bkmarking an Alarm Assigning an Alarm Acknwledging an Alarm Searching Alarms Exprting Alarms vi

7 Table f Cntents Purging an Alarm Arming Image Panels License Plates License Plate Overlay License Plate Recgnitin Watch List Reviewing the License Plate Matches Search Perfrming an Event Search Viewing Event Search Results Perfrming a Bkmark Search Viewing Bkmark Search Results Perfrming a Pixel Search Viewing Pixel Search Results Perfrming a Thumbnail Search Viewing Thumbnail Search Results Perfrming an Alarm Search Viewing Alarm Search Results Perfrming a POS Transactin Search Viewing POS Transactin Search Results Perfrming a License Plate Search Viewing License Plate Search Results Exprt Exprting a Snapsht f an Image Exprting Live Images Exprting Recrded Vide and Images Accessing the Exprt Tab Exprting Native Vide Exprting AVI Vide Exprting PNG, JPEG r TIFF Images Exprting PDF and Print Images Exprting WAV Audi Backup Backing Up Recrded Vide On Demand Appendix Accessing the Web Client vii

8 Avigiln Cntrl Center Enterprise Client User Guide Updating the Client Sftware Supprted License Plates Events and Descriptins Grup Permissin Descriptins Descriptins Rule Event and Actin Descriptins Alarm Descriptins Reprting Bugs Keybard Cmmands Image Panel & Camera Cmmands View Cmmands View Layut Cmmands Playback Cmmands PTZ Cmmands (Digital and Mechanical) Index viii

9 Intrductin What is the Avigiln Cntrl Center Client? The Avigiln Cntrl Center Client sftware wrks with the Avigiln Cntrl Center Server sftware t give yu access and cntrl f yur Avigiln High Definitin Surveillance System. The Client sftware allws yu t view live and recrded vide, mnitr alarms and events, and cntrl user access t the Avigiln Cntrl Center. The Client sftware als gives yu the ability t cnfigure the server, cameras and ther external devices that are part f yur surveillance system. The Client sftware can run n the same cmputer as the Server sftware, r run n a remte cmputer that cnnects with the Server sftware thrugh a lcal area netwrk (LAN) r a wireless area netwrk (WAN). What yu can d in the Client sftware depends n the Server sftware editin. There are three editins f the Server sftware available: Cre, Standard and Enterprise. Cre cntains all the essential sftware features fr mnitring live and recrded vide. Standard gives yu all the Cre features plus access t the pint f sales feature, digital input and utput, audi, and expanded search ptins. The Enterprise editin gives yu access t the full suite f Client sftware features, including alarms, rules, Site View, Web Pages, Maps and system backup. Visit the Avigiln website fr an verview f the features available in each editin: A cpy f the Client sftware can be dwnladed frm the Avigiln website, r installed with the Server sftware. System Requirements Minimum requirements Recmmended requirements Mnitr reslutin 1280 x x 1024 OS Windws XP with Service Pack (SP) 2 r later, Windws Vista, r Windws 7 Windws XP with Service Pack (SP) 2 r later, Windws Vista, r 1

10 Avigiln Cntrl Center Enterprise Client User Guide Windws 7 CPU Intel Single Cre 2.4 GHz prcessr Intel Dual Cre 2.0 GHz prcessr System RAM 1 GB 2 GB Vide card PCI Express, DirectX 9.0c cmpliant with 128 MB RAM (Intel GMA 900 r better, NVIDIA 6600 r better, ATI X1300 r better) PCI Express, DirectX 10.0 cmpliant with 256 MB RAM (NVIDIA GeFrce 600 series r better) Netwrk card Hard disk space 100 Mbps 1 Gbps 500 MB 500 MB Fr Mre Infrmatin Visit Avigiln at fr additinal prduct dcumentatin. Avigiln Training Center The Avigiln Training Center prvides free nline training vides that demnstrate hw t set up and use the Avigiln Surveillance System. Register nline at the Avigiln Partner Prtal site t begin: Supprt Fr additinal supprt infrmatin, visit Regular Avigiln Custmer Supprt Center hurs f peratin are frm 6:00 a.m. t 6:00 p.m. Pacific Standard Time (PST) and can be reached by calling the tll-free number: s can be sent t: supprt@avigiln.cm. Fr emergency technical supprt 24 hurs a day, 7 days a week, please call the Avigiln Emergency Technical Supprt Htline at Upgrades Sftware and firmware upgrades will be made available fr dwnlad as they becme available. Check fr available upgrades. 2

11 Intrductin Feedback We value yur feedback. Please send any cmments n ur prducts and services t feedback@avigiln.cm 3

12 Getting Started Once the Avigiln Cntrl Center Client sftware has been installed, yu can start using the Avigiln High Definitin Surveillance System immediately. Refer t any f the fllwing prcedures t help yu get started. T watch a vide verview f the applicatin, see the Intrductin t Avigiln Cntrl Center Client and Viewing Live Vide training vide in the Avigiln Training Center. Starting and Shutting Dwn the Avigiln Cntrl Center Client The Avigiln Cntrl Center Client sftware can be started r shut dwn at anytime. The Avigiln Cntrl Center Server sftware is a Windws service and will cntinue t run in the backgrund even when the Client sftware is shut dwn. Starting the Client Sftware Perfrm ne f the fllwing: Frm the Windws Start menu, select All Prgrams > Avigiln > Avigiln Cntrl Center Client > Avigiln Cntrl Center Client. Duble-click the Avigiln Cntrl Center Client shrtcut icn n the desktp. Frm the Avigiln Cntrl Center Admin Tl, click Launch Cntrl Center Client. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin. Lg in t yur server(s) when the Lg In dialg bx appears. See Lgging_In fr mre infrmatin. Shutting Dwn the Client Sftware 1. In the Avigiln Cntrl Center Client sftware, select File > Exit. 4

13 Getting Started 2. In the cnfirmatin dialg bx, click Yes. Discvering Servers The Avigiln Cntrl Center Client sftware must cmmunicate with the Avigiln Cntrl Center Server sftware t access and cnfigure yur surveillance system. If the server is n the same netwrk segment (subnet) as yur cmputer, the server is autmatically discvered and appears in the System Explrer n the left side f the applicatin windw. If the server is n a different subnet, the server must be manually discvered. There is n limit t the number f servers that can be discvered by the Client sftware. 1. Open the Find Server dialg bx. In the Lg In dialg bx, click Find Server... In the applicatin windw, select File > Manage Server Cnnectins. In the Manage Servers dialg bx, click Find Server... Figure A. Manage Server Cnnectins dialg bx 2. In the Find Server dialg bx, enter the Hstname/IP Address, the Base Prt, and the Cnnectin Speed f the server yu want t discver. 5

14 Avigiln Cntrl Center Enterprise Client User Guide Figure B. Find Server dialg bx The base prt is by default. Yu can change the base prt number in the Avigiln Cntrl Center Admin Tl. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin. 3. Click OK. Tip: Set the Cnnectin Speed t WAN if yu are n a lw bandwidth netwrk (fr example, internet r wireless netwrk), and select LAN if yu are n a high bandwidth cnnectin (fr example, ffice r hme netwrk). This enables the Avigiln Cntrl Center t better manage yur bandwidth and image rate. If the server is fund, the server will appear in the Manage Server Cnnectins dialg bx. If the server is nt fund, check the fllwing then try again: The netwrk settings are cnfigured crrectly. The firewall is nt blcking the applicatin. The Avigiln Cntrl Center Server sftware is running n the server. Lgging Int and Out f Servers T access yur Avigiln High Definitin Surveillance System thrugh the Client sftware, yu must lg in t the servers running the Avigiln Cntrl Center Server sftware. Whenever the Client sftware detects a server with the Server sftware installed, yu are prmpted t lg in. The default administratr access uses administratr as the username and n passwrd. T maintain the security f the administratr accunt, it is recmmended that yur system administratr immediately create a passwrd fr this accunt after the first lgin. Yur system administratr can then create user accunts fr ther users. If the Client sftware des nt detect any servers, click Find Server... See Discvering Servers fr mre infrmatin. 6

15 Getting Started Lgging In Be aware that the number f servers yu can lg int at ne time is determined by the type f server yu can access. Standard editin servers nly allw yu t be lgged int three servers at the same time, while Enterprise editin servers allw yu t be lgged int an unlimited number f servers. Nte: Yu cannt access Standard editin servers and Enterprise editin servers at the same time. 1. Open the Lg In dialg bx. The Lg In dialg bx autmatically appears when a server is detected by the Client sftware. T manually access the Lg In dialg bx, perfrm ne f the fllwing: Frm the File menu, select Lg In t lg in t all available servers In the System Explrer, right-click a server and select Lg In t lg in t the selected server. 2. In the Lg In dialg bx, select a specific server r select All Servers frm the Lg in t drp dwn list. Figure A. Lg In dialg bx Tip: If yu accessed the Lg In dialg bx frm a specific server, yu will nt have the ptin f lgging int All Servers. If the server yu want t lg int is nt shwn, click Find Server... t try t discver the server. 3. Enter yur User Name and Passwrd, r select the Use current Windws credentials check bx if yur system administratr has imprted yur Windws accunt infrmatin int the server. 4. Click Lg In. After lgging in the first time, yu can set up autmatic lgin frm the client Setup dialg bx. See Changing General Client Settings fr mre infrmatin. 7

16 Avigiln Cntrl Center Enterprise Client User Guide Lgging Out Yu can lg ut f ne r all servers at any time. T Lg ut f ne server D this 1. Right-click the server in the System Explrer and select Lg Out. Lg ut f all servers 1. Select File > Lg ut. 2. When the Lg Out dialg bx appears, click Yes. Navigating the Applicatin Once yu lg in, the Avigiln Cntrl Center Client applicatin windw is where yu setup yur surveillance system, mnitr vide, and view, search, and exprt recrded vide. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. 8

17 Getting Started Figure A. Avigiln Cntrl Center Client applicatin windw. Area Wrkspace 1 Menu bar 2 Tlbar 3 View Descriptin The right pane where the feature tabs appear. A standard Windws applicatin menu that prvides access t features nt available n the Tlbar. Prvides quick access t cmmnly used tls. If any buttns are missing frm yur tlbar, click the small dwn arrw n the right-edge f the tlbar t display the hidden buttns. Prvides a way t rganize image panels. Yu can have multiple Views pen at nce. This is the mst cmmn tab in the Wrkspace. 4 Image panel Displays live r recrded vide frm a camera. 5 System Explrer Displays all the servers and cameras in yur surveillance system. 9

18 Avigiln Cntrl Center Enterprise Client User Guide When yu right-click any item in the System Explrer, yu have the ptin t Expand All r Cllapse All items in the System Explrer. 6 PTZ Cntrls Prvides a way t cntrl pan and tilt and zm (PTZ) cameras. 7 Timeline Displays the Timeline fr a recrded vide, and cntains clrcded events. This tl allws yu t review vide fr a specific time frame, and cntrl the vide playback. Nte: The Timeline nly appears fr recrded vide. Adding and Remving Cameras in a View T mnitr vide, add a camera t the View. The camera vide can be remved frm the View any time. Adding a Camera t a View Perfrm ne f the fllwing: Drag the camera frm the System Explrer t an empty image panel in the View. Duble-click a camera in the System Explrer. In the System Explrer, right-click the camera and select Add t View. The camera is added t the next empty image panel in the View layut. Tip: Yu can drag the same camera t multiple image panels t watch the vide at different zm levels. Remving a Camera Frm a View Perfrm ne f the fllwing: Right-click the image panel and select Clse. Inside the image panel, click Clse. 10

19 Getting Started Viewing Live and Recrded Vide Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. When yu mnitr vide, yu can chse t watch live and recrded vide in the same View, r nly ne type f vide per View. Once yu've added the required cameras t the View, perfrm the fllwing: 1. T switch the View between live and recrded vide, perfrm ne f the fllwing: Select View > Live r Recrded. On the tlbar, select either Live r Recrded. 2. T switch individual image panels between live and recrded vide, right-click the image panel and select either Live r Recrded. Image panels displaying live vide have a blue brder, while image panels displaying recrded vide have a green brder. 11

20 Setup The default settings in the Avigiln Cntrl Center Client sftware allw yu t start wrking with the applicatin immediately after installatin. If yu have special requirements, refer t the fllwing sectins t cnfigure yur settings: Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Managing Server Cnnectins When yu start the applicatin, yu autmatically have access t all the servers cnnected t yur netwrk. If yu need t access a server that is n a different netwrk segment, yu need t manually discver the server. Once yu are cnnected t a server, yu can als change hw yu cnnect t the server. Discvering Servers The Avigiln Cntrl Center Client sftware must cmmunicate with the Avigiln Cntrl Center Server sftware t access and cnfigure yur surveillance system. If the server is n the same netwrk segment (subnet) as yur cmputer, the server is autmatically discvered and appears in the System Explrer n the left side f the applicatin windw. If the server is n a different subnet, the server must be manually discvered. There is n limit t the number f servers that can be discvered by the Client sftware. 1. Open the Find Server dialg bx. In the Lg In dialg bx, click Find Server... In the applicatin windw, select File > Manage Server Cnnectins. In the Manage Servers dialg bx, click Find Server... 12

21 Setup Figure A. Manage Server Cnnectins dialg bx 2. In the Find Server dialg bx, enter the Hstname/IP Address, the Base Prt, and the Cnnectin Speed f the server yu want t discver. Figure B. Find Server dialg bx The base prt is by default. Yu can change the base prt number in the Avigiln Cntrl Center Admin Tl. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin. 3. Click OK. Tip: Set the Cnnectin Speed t WAN if yu are n a lw bandwidth netwrk (fr example, internet r wireless netwrk), and select LAN if yu are n a high bandwidth cnnectin (fr example, ffice r hme netwrk). This enables the Avigiln Cntrl Center t better manage yur bandwidth and image rate. If the server is fund, the server will appear in the Manage Server Cnnectins dialg bx. If the server is nt fund, check the fllwing then try again: 13

22 Avigiln Cntrl Center Enterprise Client User Guide The netwrk settings are cnfigured crrectly. The firewall is nt blcking the applicatin. The Avigiln Cntrl Center Server sftware is running n the server. Editing and Deleting a Server Cnnectin Use the Manage Server Cnnectins dialg bx t edit and delete yur server cnnectins. 1. Select File > Manage Server Cnnectins. Figure A. Manage Server Cnnectins dialg bx 2. Select a server n the Server list then perfrm ne f the fllwing: Nte: Yu cannt remve r edit the IP address and base prt f servers that were autmatically discvered. T edit the server cnnectin, click Edit. Update the server IP Address, Base Prt and Cnnectin Speed as required then click OK. Refer t Discvering Servers fr details abut the editable ptins. T delete the server cnnectin, click Remve Server. 14

23 Setup Cnnect/Discnnect Cameras Yu can cnnect and discnnect cameras t servers using the Cnnect/Discnnect Cameras dialg bx. A camera's cnnectin status is indicated by the icn beside the camera name in the System Explrer. Icn Definitin Camera Cnnected The camera is cnnected t the server. Camera Upgrading Camera Cnnectin Errr The camera is cnnected t the server and is currently upgrading its firmware. The camera cannt cnnect t a server. This may be because the camera is n lnger n the netwrk r there is a netwrk cnflict Camera Discnnected N icn The camera is discnnected but there is recrded vide frm the camera still n the server. The camera is discnnected and there is n recrded vide left n the server. Discvering a Camera When cameras are cnnected t the netwrk, they shuld be autmatically discvered by the Avigiln Cntrl Center Client sftware. If a camera is nt autmatically discvered, yu can try t manually discver the camera n the netwrk. Frm the Tls menu, select Cnnect/Discnnect Cameras. In the Cnnect/Discnnect Cameras windw, all Avigiln and ONVIF cameras cnnected t the same netwrk segment (subnet) as the Avigiln Cntrl Center Server are autmatically detected and appear in the Discvered Cameras list. If the camera yu want t cnnect t is n a different subnet, r is manufactured by a third party, perfrm the fllwing: 1. At the tp f the Cnnect/Discnnect Cameras dialg bx, click Find Camera In the Find Camera dialg bx, cmplete the fllwing fields: 15

24 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Find Camera dialg bx: IP Address Figure B. Find Camera dialg bx: IP Address Range Search Frm Server: select the server that yu want the camera t cnnect t. Search Type: select a search type. Camera Type: select the camera's brand name. Tip: Select ONVIF t discver cameras that are ONVIF cmplaint. IP Address/Hstname: (Fr IP Address search nly) enter the camera's IP address r hstname. The camera and server s gateway IP address must be set crrectly fr the camera t be fund. Start IP Address and End IP Address: (Fr IP Address Range search nly) enter the start and end IP addresses. Only addresses in that range will be searched fr the selected camera type. Cntrl Prt: enter the camera cntrl prt number. Prvide the User Name and Passwrd fr the camera if required. 3. Click OK. If the camera is discvered, it will appear in the Discvered Cameras list. Yu can nw cnnect the camera t a server. Cnnecting a Camera t a Server Once the camera has been discvered n the netwrk, it can be cnnected t the server. 16

25 Setup 1. Frm the Tls menu, select Cnnect/Discnnect Cameras. The Cnnect/Discnnect Cameras dialg bx appears. Figure A. Cnnect/Discnnect Cameras dialg bx 2. In the Discvered Cameras area, select a camera then click Cnnect... Tip: Yu can als drag the camera t a server n the Cnnected Cameras list, then yu can skip the next 3 steps. The camera will autmatically make a Primary cnnectin t the server. 3. In the Cnnect Camera dialg bx, select the server yu want the camera t cnnect t. 17

26 Avigiln Cntrl Center Enterprise Client User Guide Figure B. Cnnect Camera dialg bx 4. In the Cnnectin Type drp dwn list, select ne f the fllwing: Primary: the camera will autmatically cnnect t this server if they are n the same netwrk. Secndary: the camera will try t cnnect t this server if they are n the same netwrk, and the primary server is nt available. Tertiary: the camera will try t cnnect t this server if they are n the same netwrk, and the primary and secndary servers are nt available. Select Secndary r Tertiary t create a failver cnnectin. See Failver Cnnectins fr mre infrmatin. 5. In the License Pririty drp dwn list, select the apprpriate license pririty. 1 is the highest pririty and 5 is the lwest. Nte: server. This ptin is nly available if yu are cnnecting t a secndary r tertiary The License Pririty setting decides the rder that cameras are cnnected t the server. The server will try t cnnect cameras with a higher license pririty befre cameras with lwer pririty. If the server des nt have enugh camera channel licenses, lw pririty cameras may nt be cnnected. A camera channel license is nly used when the camera actually cnnects t the server. 6. Click OK. 7. If the camera is passwrd prtected, the Camera Authenticatin dialg bx appears. Enter the camera's username and passwrd, then click OK. Editing the Camera Cnnectin t the Server 1. Frm the Tls menu, select Cnnect/Discnnect Cameras. 2. In the Cnnect/Discnnect Cameras dialg bx, select the camera cnnectin yu want t edit frm the Cnnected Cameras list. 3. Click Edit. Refer t Cnnecting a Camera t a Server fr details abut the editable ptins. 4. Click OK. Failver Cnnectins Yu can set up failver cnnectins s that if a server fails, the cameras cnnected t it will autmatically cnnect t a backup server and cntinue recrding. 18

27 Setup Failver cnnectins are set up in the Cnnect/Discnnect Cameras dialg bx. When yu cnnect a camera t a server, yu are asked t select the Cnnectin Type and License Pririty. The Cnnectin Type determines when the camera will cnnect t a server: Primary: the camera will autmatically cnnect t this server if they are n the same netwrk. Secndary: the camera will try t cnnect t this server if they are n the same netwrk, and the primary server is nt available. Tertiary: the camera will try t cnnect t this server if they are n the same netwrk, and the primary and secndary servers are nt available. The License Pririty setting decides the rder that cameras are cnnected t the server 1 is the highest and 5 is the lwest. The server will try t cnnect cameras with a higher license pririty befre cameras with lwer pririty. If the server des nt have enugh camera channel licenses, lw pririty cameras may nt be cnnected. A camera channel license is nly used when the camera actually cnnects t the server. T set up a failver cnnectin, cmplete the Cnnecting a Camera t a Server prcedure and set the failver Cnnectin Type and License Pririty. Example Cameras A, B, C, D, E and F have failver cnnectins set up t tw different servers. Assume each server has 6 camera channel licenses, and the license pririty is set t 1 fr each cnnectin. Figure A. Primary cnnectins When the first server fails, cameras A and B frm NVR 1 autmatically cnnect t their Secndary server, NVR 2. 19

28 Avigiln Cntrl Center Enterprise Client User Guide Figure B. NVR 1 fails When the secnd server fails, cameras E and F autmatically cnnect t their Tertiary server, NVR 2. Figure C. NVR 2 fails Discnnecting a Camera frm a Server 1. Frm the Tls menu, select Cnnect/Discnnect Cameras. 2. In the Cnnect/Discnnect Cameras dialg bx, select the camera yu want t discnnect frm the Cnnected Cameras list then perfrm ne f the fllwing: 20

29 Setup Click Discnnect. The camera is discnnected frm the server and mved t the Discvered Cameras list. Drag the camera int the Discvered Cameras list. Upgrading Camera Firmware Camera firmware updates are typically included with the Avigiln Cntrl Center Server update packages. Camera firmware updates are autmatically dwnladed and installed t the camera. When the camera firmware is being upgraded, vide frm that camera cannt be displayed and the System Explrer will display the fllwing symbl beside the camera. Figure A. System Explrer: camera firmware upgrade When the firmware upgrade is cmplete, the System Explrer will display the Camera Cnnected icn again, and vide frm the camera will display. Server Setup The server Setup dialg bx is respnsible fr all the Avigiln Cntrl Center features that are cnfigured and stred n the server. Refer t any f the fllwing sectins t access and cnfigure the server setup. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Accessing the Server Setup Perfrm ne f the fllwing steps t pen the server Setup dialg bx: Select Tls > Setup... then select the server yu want t setup frm the left pane. In the System Explrer pane, right-click the server and select Setup. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. 21

30 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Server Setup dialg bx General Use the General dialg bx t change the name the server displays in the System Explrer. Changing the Server's Name The default name fr the server may nt be useful fr yur purpses. Use the General dialg bx t change the server's name t smething mre meaningful t yur surveillance system. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click General. 22

31 Setup 3. In the General dialg bx, enter a new server name. Figure A. General dialg bx 4. Click OK. Recrding Schedule Use the Recrding Schedule dialg bx t set the recrding schedule fr the cameras cnnected t the server. By default, the Avigiln Cntrl Center is set t recrd mtin and cnfigured events when they ccur. Once the recrding schedule is set, camera recrdings are made autmatically. Using Templates t Mdify the Recrding Schedule The recrding schedule is set by using templates that tell cameras what t recrd and when t recrd. Fr example, yu can create ne recrding schedule template fr the weekdays and anther fr the weekend. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Adding a Template 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Recrding Schedule. 3. In the Recrding Schedule dialg bx, click Add Template in the Templates pane. 23

32 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Schedule dialg bx 4. Enter a name fr the template. 5. Click the Set Area buttn then click r drag the cursr acrss the Recrd Mde timeline t set the types f events that the cameras will recrd thrughut the day. Recrd Mde Cntinuus Mtin Digital Input Alarms POS Transactins Definitin Recrd vide cnstantly. Only recrd vide when mtin is detected. Only recrd vide when a digital input is activated. Only recrd vide when an alarm has been activated. Only recrd vide when pint f sale (POS) transactins are made. License Plates Only recrd vide when a license plate is detected. 6. T disable recrding in parts f the template, click the Clear Area buttn then click r drag the cursr acrss the timeline t remve the set recrding areas. 7. If cameras are nt recrding in Cntinuus mde all day, yu can set cameras t recrd reference images between events in the recrding schedule. Select the Recrd a reference image every: check bx then set the time between each reference image. Editing and Deleting a Template 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Schedule. 3. In the Schedule dialg bx, select a template frm the Templates pane and perfrm ne f the fllwing: T edit a template, mdify the schedule. 24

33 Setup T rename a template, click Rename Template and enter a new name. T delete a template, click Delete Template. 4. Click OK. Setting Up a Weekly Recrding Schedule Yu can set up a week s recrding schedule by applying templates t cameras fr each day f the week. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Recrding Schedule. 3. In the Recrding Schedule dialg bx, select a template frm the Templates pane. 4. In the Default Week area, select the cameras and days f the week this template applies t. Figure A. Recrding Schedule dialg bx: Default Week 5. Click OK. Recrding and Bandwidth While the Schedule dialg bx sets what cameras recrd, the Recrding and Bandwidth dialg bx sets hw lng camera recrdings are kept. Yu can use the Recrding and Bandwidth dialg bx t change the data aging settings and maximum recrding times fr each camera that is cnnected t the server. Changing Recrding Settings 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 25

34 Avigiln Cntrl Center Enterprise Client User Guide 2. Click Recrding and Bandwidth. The Recrding and Bandwidth dialg bx appears. Figure A. Recrding and Bandwidth dialg bx The Data Aging clumn shws an estimate f the recrding time that is available at each image rate given the amunt f space n the server. Fr JPEG2000 r JPEG cmpressin cameras, data aging is available at three rates. Full Image Rate and Reslutin keeps recrdings in its riginal quality, while Half Image Rate discards half f the recrded data t make rm fr new recrdings, and Quarter Image Rate keeps 1/4 f the riginal recrded data s that yu can still see lder vide. Fr H.264 cameras that supprt data aging, data aging is available at tw rates. Full Image Rate and Reslutin keeps the riginal high quality vide and the secndary stream f lw reslutin vide. Lw Reslutin nly keeps the secndary stream f lw reslutin vide. Nte: Data aging can nly ccur when the secndary stream is enabled. Fr H.264 cameras that d nt supprt data aging, nly the Full Image Rate and Reslutin vide is kept. 3. In the Data Aging clumn, mve the sliders t adjust the amunt f time vide is stred at each image rate. T change the data aging settings fr all linked cameras, mve the slider fr ne linked camera and all linked cameras are updated. 26

35 Setup T change the data aging setting fr ne camera, break the camera's link t the ther cameras by clicking the Link icn t the left f the camera's name, then make yur changes. 4. In the Max. Recrd Time clumn, manually enter a maximum recrd time r select ne f the ptins frm the drp dwn list fr each camera. 5. Click OK. Nte: If the time estimated in the Ttal Recrd Time clumn is shrter than what is set in the Max. Recrd Time clumn, the camera's actual recrding time may be shrter than what is set. Users and Grups When users are added t the Avigiln Cntrl Center, they are assigned t an access grup that defines their permissins n the server. Use the Users and Grups dialg bx t create and manage users and grups. Adding a User 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Users and Grups. 3. In the User and Grups dialg bx, click Add User. 27

36 Avigiln Cntrl Center Enterprise Client User Guide Figure A. User and Grups dialg bx 4. When the Add User dialg bx appears, cmplete the User Infrmatin area. 28

37 Setup Figure B. Add User dialg bx, General tab 5. If yu dn t want this user t be active yet, select the Disable user check bx. Disabled users are in the system but cannt access the server. 6. In the Lgin Timeut area, select the Enable lgin timeut check bx t limit the amunt f time the user can be lgged in while the applicatin is idle. 7. In the Passwrd area, cmplete the fllwing fields: Passwrd: enter a passwrd fr the user. Cnfirm Passwrd: re-enter the passwrd. Require passwrd change n next lgin: select this check bx if the user must replace the passwrd after the first lgin. 29

38 Avigiln Cntrl Center Enterprise Client User Guide Passwrd Expiry (Days): specify the number f days befre the passwrd must be changed. Passwrd never expires: select this check bx if the passwrd never needs t be changed. 8. Select the Member Of tab and select the check bx beside each access grup the user belngs t. The ther tw clumns display the permissins linked t the selected grup. Figure C. Add User dialg bx, Member Of tab 9. Click OK. The user is added t the server. Editing and Deleting a User Yu can edit and delete users as needed. Nte: server. If a user has access t mre than ne server, the changes t the user need t be made n each 30

39 Setup 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Users and Grups. 3. In the Users and Grups dialg bx, select a user then perfrm ne f the fllwing: T edit the user's infrmatin, click Edit User. Refer t Adding a User r details abut the editable ptins. T delete the user, click Delete User. Nte: Users imprted thrugh the Active Directry tab cannt be deleted, nly disabled. Adding Grups Grups define what features users have access t. Create new grups t tailr what users can access. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Users and Grups. 3. In the Users and Grups dialg bx, select the Grups tab and click Add Grup. 31

40 Avigiln Cntrl Center Enterprise Client User Guide Figure A. User and Grups dialg bx 4. In the Add Grup dialg bx, select a grup t use as a template fr yur new grup and click OK. Figure B. Add Grup dialg bx 5. In the Edit Grup dialg bx, give the new grup a name then select the permissins and camera access rights fr the grup. Clear the check bx f any feature r camera yu d nt want the grup t access. 32

41 Setup Figure C. Edit Grup dialg bx: Grup tab 6. Select the Members tab t add users t the grup. 33

42 Avigiln Cntrl Center Enterprise Client User Guide Figure D. Edit Grup dialg bx: Members tab a. Click Add User... b. Select the users that shuld be part f this new grup. 34

43 Setup Figure E. Add users t grups dialg bx c. Click OK. The users are added t the Members list. If a user is added t the grup thrugh the Add User r Edit User dialg bx, the user is autmatically added t the grup's Members list. 7. Click OK t save the new grup. Imprting Active Directry Grups Yu can imprt Active Directry grups t the server t allw users t lg in using their Windws credentials. Members f an imprted Active Directry grup are autmatically added as users, and changes t member accunts in the Active Directry are autmatically synchrnized. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Users and Grups. 3. In the Users and Grups dialg bx, select the Active Directry tab. 35

44 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Users and Grups dialg bx 4. Click Add Grup. If the Change User dialg bx appears, yu need t enter yur username and passwrd fr the dmain befre yu can cntinue. 5. In the Add Grup dialg bx, assign a permissins grup t the grup yu are imprting then click OK. Yu can edit the permissins fr the grup later. Yu may be prmpted t enter yur dmain username and passwrd again. 6. In the Select Grups dialg bx, lcate the Windws grup yu wish t imprt by perfrming ne f the fllwing: Enter the name f a Windws grup in the Enter the bject names t select field and click OK. Click the Advanced buttn and search fr the grups t imprt. 36

45 Setup Figure B. Select Grups dialg bx Once lcated, the grup is autmatically added t the Active Directry list and the Grups list. All the users in the grup are imprted int the Users list. T edit the permissins assigned t the imprted grup, see Editing and Deleting a Grup. Imprted user infrmatin, including lg in credentials, are maintained by the Active Directry. In the Users and Grups dialg bx, yu can nly disable an imprted user r cnfigure the lgin timeut settings. Fr mre infrmatin see Editing and Deleting a User. Editing and Deleting a Grup Yu can change the access permissins fr a set f users by editing their access grup. Nte: Active Directry grups can nly be deleted frm the Active Directry tab. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Users and Grups and select the Grups tab. 3. Select a grup and perfrm ne f the fllwing: T edit the grup, click Edit Grup. Refer t Adding Grups fr details abut the editable ptins. T delete the grup, click Delete Grup. Nte: Default grups cannt be deleted. 37

46 Avigiln Cntrl Center Enterprise Client User Guide Alarms Use the Alarms dialg bx t create and manage alarms. Alarm triggers can include Mtin Detectin, Digital Input Activatin, License Plate Watch List match, POS Transactin Exceptin, Camera Errr, System Errr and External Sftware Event. Adding a New Alarm Alarms need t be added t the server Setup befre they can be mnitred in the Alarms tab. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Alarms. 3. In the Alarms dialg bx, click Add. 4. Select the Alarm Trigger Surce then select the required features fr the alarm and click Next. Figure A. Select Alarm Trigger Surce page 5. Select the cameras t link t this alarm then cmplete the fllwing: 38

47 Setup Figure B. Select Linked Cameras page a. Set the Pre-Alarm Recrd Time and the Recrding Duratin. b. Select the View linked cameras when alarm is triggered check bx t autmatically display the alarm vide in a View when the alarm is triggered. c. Click Next. 6. Select the grups and users that need t receive alarm ntificatins, and decide if the applicatin will play a sund whenever the alarm is triggered. Then click Next. 39

48 Avigiln Cntrl Center Enterprise Client User Guide Figure C. Select Alarm Recipients page 7. (Optinal) Set the actins that must ccur when an alarm is acknwledged. Figure D. Select Alarm Acknwledgement Actin page 40

49 Setup a. If the user must add cmments abut the alarm, select the Require a cmment when acknwledging alarm check bx. b. If a digital utput must be activated when the alarm is acknwledged, select the Activate selected digital utputs n alarm acknwledgement check bx. Then, select the digital utputs t be activated. c. If the digital utput shuld nly be activated when cnfirmed by a user, select the Require user cnfirmatin befre activating digital utput(s) check bx. d. Click Next. 8. On this page, cmplete the fllwing: Figure E. Select Alarm Prperties page a. Enter a name fr the alarm. b. Select a pririty fr the alarm. Pririty: 1 is the highest alarm pririty. c. Select a schedule fr the alarm. See Scheduling Server Events fr mre infrmatin. d. Make sure the Enable Alarm check bx is selected t enable the alarm. 9. Click Finish. 41

50 Avigiln Cntrl Center Enterprise Client User Guide Editing and Deleting Alarms 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Alarms. 3. In the Alarms dialg bx, select an alarm then perfrm ne f the fllwing: Figure A. Alarms dialg bx: alarm prperties 4. Perfrm ne f the fllwing: T edit the alarm, click Edit. G thrugh the Add Alarm wizard and make the required changes n each page. On the last page, click Finish t save yur changes. Refer t Adding a New Alarm fr details abut the editable ptins. T delete the alarm, click Delete. 42

51 Setup Scheduled Backup Data backup must be enabled n the server befre Scheduled Backup settings can be made in the applicatin. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin abut enabling backup n the server thrugh the Avigiln Cntrl Center Admin Tl. Files are always backed up in the Avigiln Backup (AVK) frmat. Yu can review backed up vide in the Avigiln Cntrl Center Player. Changing Scheduled Backup Settings Use the Scheduled Backup dialg bx t set when vide is backed up t the server. Nte: The vide backup lcatin is cnfigured in the Avigiln Cntrl Center Admin Tl. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Scheduled Backup. Figure A. Scheduled Backup dialg bx 3. Select the Enable scheduled backups check bx. 43

52 Avigiln Cntrl Center Enterprise Client User Guide 4. In the Camera(s) t Backup area select all the cameras t backup. 5. In the Backup Optins area, cmplete the fllwing: Perfrm Every <X> day(s): specify the number f days between backups Start Time: the time when backup ccurs Cverage: the amunt f recrded image data that is backed up Starting Frm: starting pint fr the backup Delete ldest backups when disk full: select this check bx t autmatically delete the ldest backups when the backup strage lcatin is full Fr example in the figure abve, the Scheduled Backup is cnfigured t ccur every day at 12a.m. Vide starting frm 30 days ag is backed up and the back up nly cvers 1 day, s nly the 30th day is backed up t the remte server each night. 6. Click OK. The Status area displays when the next backup will be. POS Transactins The Pint f Sale (POS) Transactin Engine is a licensed feature that recrds vide and raw data frm POS transactin surces. POS transactin surces can be added t the Avigiln Cntrl Center and cnfigured in the Client sftware. Adding a POS Transactin Surce 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click POS Transactins. 3. In the POS Transactins dialg bx, click Add. 4. Enter the Hstname/IP Address and the Prt number fr the POS Transactin Surce device, then click Next. 44

53 Setup Figure A. Set Transactin Surce Device page 5. Select a Transactin Surce Data frmat then click Next. If the surce data frmat needs t be added, click Add. Or, click Cpy Frm t create a new data frmat based n the selected data frmat. See Adding a Transactin Surce Data Frmat fr mre infrmatin. 45

54 Avigiln Cntrl Center Enterprise Client User Guide Figure B. Set POS Transactin Surce Data Frmat page 6. On the Set Transactin Exceptins page, select any exceptins that need be mnitred then click Next. If exceptins d nt need t be mnitred, just click Next. Click Add t add an exceptin. See Adding a Transactin Exceptin fr mre infrmatin. 46

55 Setup Figure C. Set Transactin Exceptins page 7. Select the cameras t link t the transactin surce, and set the amunt f time vide needs t be recrded befre and after each transactin. Then click Next. Figure D. Select Linked Cameras page 8. Enter a name and descriptin fr the transactin surce, then select Enable transactin surce t start receiving data frm the transactin surce. 47

56 Avigiln Cntrl Center Enterprise Client User Guide Figure E. Set Transactin Surce Name and Descriptin page 9. Click Finish. Adding a Transactin Surce Data Frmat When yu add a new POS transactin surce, be aware that the transactin surce must have a surce data frmat. In the POS Transactin Setup wizard, click Add when yu arrive n the Set Transactin Surce Data Frmat page. When the Cnfigure Data Frmat dialg bx appears, cmplete the fllwing prcedure: 1. In the Prperties area, specify the fllwing: Figure A. Cnfigure Data Frmat dialg bx Name: enter a name fr the data frmat. 48

57 Setup Descriptin: enter a descriptin f the data frmat. Transactin Start Text: (required) enter the text that identifies the start f each transactin frm the POS transactin surce. Transactin End Text: (ptinal) enter the text that identifies the end f each transactin. Encding: Select the encding used by the POS transactin surce. 2. The fllwing figure shws raw transactin data n the left and filtered transactin data n the right. Perfrm any f the fllwing t capture raw data fr the surce data frmat: Figure B. Cnfigure Data Frmat dialg bx Click Capture Data t start capturing a raw transactin data sample. Click Stp Capture t stp capturing transactin data. Click Lad Data t lad raw transactin data frm a file. Click Save Data t save a cpy f the transactin data that has been captured. 3. (Optinal) Click Add Filter t create a new filter fr the raw transactin data file. There are tw default filters in the Current Filters area: ne t create line breaks and the ther t delete extra white space at the beginning f each line. If yu d nt need extra filters, skip this step. 49

58 Avigiln Cntrl Center Enterprise Client User Guide 2. Figure C. Cnfigure Filter dialg bx a. In the Text field, enter text fr the filter t search fr. b. Select Match case and/r Match whle wrd check bx t fcus the text filter t nly find text with the same capitalizatin r match the text exactly. c. In the Methd drp dwn list, select a search methd. Yu can chse t filter text fund thrugh a Nrmal search, Wildcard search r Regular Expressin search. d. In the Actin t Take area, select which actin t take when the filter finds a match t yur text criteria. e. Click OK. 3. On the Cnfigure Data Frmat screen, click OK t add the new data frmat t the data frmat list. Adding a Transactin Exceptin T help mnitr unusual transactins, yu can set up transactin exceptins. Transactin exceptins can help yu identify unauthrized discunts, fake returns, and manual price verrides. In the POS Transactin Setup wizard, click Add when yu arrive n the Set Transactin Exceptins page. When the Cnfigure Exceptin dialg bx appears, cmplete the fllwing prcedure: 50

59 Setup Figure A. Cnfigure Exceptin dialg bx 1. Enter a name. 2. Select ne f the Text t Match ptins: Select Match Text Match Value And d this... Enter text fr the exceptin t search fr. The exceptin will mnitr all transactins fr the text entered in the Text t Match field. Enter the value that triggers the exceptin, and enter the text that may appear arund the value. The exceptin will mnitr all transactins fr values that match what yu enter in the Text Befre Value, Match When Value and Text After Value fields 3. Click OK. Editing and Deleting a POS Transactin Surce 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click POS Transactins. 51

60 Avigiln Cntrl Center Enterprise Client User Guide Figure A. POS Transactins dialg bx 3. In the POS Transactin dialg bx, select a POS transactin surce then perfrm ne f the fllwing: T edit the POS transactin surce, click Edit. G thrugh the POS Transactin Setup wizard and make the required changes n each page. On the last page, click Finish t save yur changes. Refer t Adding a POS Transactin Surce fr details abut the editable ptins. T delete the POS transactin surce, click Delete. When the cnfirmatin dialg bx appears, click OK. Ntificatin Use the Ntificatin dialg bx t prepare the server fr sending messages in respnse t specific events. Yu can set what events require ntificatin and wh receives the s. Setting Up the Server Befre s can be sent, the server must be set up t send s. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Ntificatin. 52

61 Setup 3. In the Ntificatin dialg bx, select the Server tab. Figure A. Ntificatins dialg bx: Server tab 4. In the Server Settings area, cmplete the fllwing a. Sender Name: enter a name fr the server sending ut the . b. Sender Address: enter an address the server can use t send s. c. Subject Line: enter a default subject line fr all s sent frm this server. d. SMTP Server: enter the SMTP server address used by the . e. Prt: enter the SMTP prt. f. Timeut (secnds): enter the maximum number f secnds the server will try t send an befre it quits. 5. (Optinal) If the server uses encryptin, yu can select the Use secure cnnectin (TLS/SSL) check bx. 6. (Optinal) If the accunt has a username and passwrd, select the Server requires authenticatin check bx. a. Enter the Username and Passwrd fr the accunt. 7. Click OK. 53

62 Avigiln Cntrl Center Enterprise Client User Guide Cnfiguring Ntificatin In the Ntificatin dialg bx, yu can create ntificatin grups t specify wh will receive ntificatins when an event ccurs. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Ntificatin. 3. In the Ntificatin dialg bx, ensure the Ntificatin tab is selected. 4. Click Add. Figure A. Ntificatins dialg bx 5. Enter a name fr the new grup. 54

63 Setup 6. In the Recipients area, add all the users, grups and s that are part f this grup. Perfrm any f the fllwing: Click Add User/Grup t add an Avigiln Cntrl Center user r access grup. In the dialg bx, select all the required users and grups then click OK. Click Add t add individual s. In the dialg bx, enter the address then click OK. Tip: Make sure the Avigiln users and grups added t the Recipient list have a valid in their user accunt. 7. Click Send Test t send a test t everyne n the Recipients list. 8. In the Trigger area, select all the events that this grup will be ntified f. Click the blue text t define the event requirements. Tip: If yu require ther events r mre specific requirements, yu can als cnfigure ntificatin in the rules engine. See Rules fr mre infrmatin. 9. T attach a snapsht f the ntificatin event, select the Attach images frm camera(s) linked t the event check bx. Nte: This ptin is disabled if nly System Events is selected because cameras cannt be linked t System Events. 10. In the Schedule area, select a schedule fr the ntificatin. See Scheduling Server Events fr mre infrmatin. 11. T limit the number f s sent, enter the amunt f time between each in the Send at mst every: field. 12. Click OK. Editing and Deleting an Ntificatin Yu can edit the details f an ntificatin r delete the ntificatin when it is n lnger needed. 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Ntificatin. 3. In the Ntificatin dialg bx, ensure the Ntificatin tab is selected then perfrm ne f the fllwing: T edit the ntificatin, select the Grup and make the required changes. Refer t Cnfiguring Ntificatin fr details abut the editable ptins. T delete the ntificatin, select the Grup and click Remve. 55

64 Avigiln Cntrl Center Enterprise Client User Guide Rules The rules engine allws yu t trigger specific actins when certain events ccur. Fr example, yu can create a rule that starts a live stream when a license plate n the Watch List is detected. Adding a Rule 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Rules. 3. In the Rules dialg bx, click Add. 4. Select the events that will trigger the rule. If blue underlined text appears in the rule descriptin, click n the text t further define the event. Figure A. Select Rule Event(s) page 5. When the trigger event is defined, click Next. 56

65 Setup 6. Select the actins that will ccur when the rule is triggered. If any blue underlined text appears in the rule descriptin, click n the text t further define the actin. When the actin is defined, click Next. Figure B. Select Rule Actin(s) page 7. On this page, cmplete the fllwing: 57

66 Avigiln Cntrl Center Enterprise Client User Guide Figure C. Set Rule Name and Descriptin page a. Give the rule a name and descriptin. b. Select a schedule fr the Rule. See Scheduling Server Events fr mre infrmatin. c. Make sure the Rule is enabled check bx is selected t enable the rule. 8. Click Finish. Editing and Deleting a Rule 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click Rules. 3. In the Rules dialg bx, select a rule then perfrm ne f the fllwing: 58

67 Setup Figure A. Rules dialg bx T edit the rule, click Edit. G thrugh the Rules Setup wizard and make the required changes n each page. On the last page, click Finish t save yur changes. Refer t Adding a Rule fr details abut the editable ptins. T delete a rule, click Delete. When the cnfirmatin dialg bx appears, click OK. System Lg The system lg recrds events that ccur in the Avigiln Cntrl Center. This can be useful fr tracking system usage and diagnsing issues. Yu can filter the items displayed in the lg and save the lg t a separate file fr sending t Avigiln supprt. Nte: The system lg maintains a recrd f system events fr up t 90 days. 59

68 Avigiln Cntrl Center Enterprise Client User Guide Viewing the System Lg 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click System Lg. 3. In the System Lg dialg bx, select the lg events yu want t display in the Event Types t Shw area, then click Start Search. The search results are displayed in the left pane. Figure A. System Lg dialg bx 4. Select a result t display the event details n the right. 5. T save the lg search results, click Save events t file... and save the file. 6. Click Clse. License Plate Recgnitin License Plate Recgnitin (LPR) is a licensed feature that allws users t read and stre vehicle license plate numbers frm any vide streamed thrugh the Avigiln Cntrl Center. 60

69 Setup Nte: The License Plate Recgnitin ptins will nly appear if yu have the feature licensed and installed n the server. Setting Up License Plate Recgnitin 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click License Plate Recgnitin. 3. When the License Plate Recgnitin dialg bx appears, select a lane frm the left pane. The number f lanes listed is determined by the number f License Plate Recgnitin (LPR) channels licensed n the server. Figure A. License Plate Recgnitin dialg bx, Settings tab 4. Cmplete the fllwing fields: Name: enter a name fr the lane. 61

70 Avigiln Cntrl Center Enterprise Client User Guide Camera: select the camera that will perfrm LPR. One camera can be used fr multiple lanes. License Plate Cnfiguratin: select the reginal license plate frmat that needs t be recgnized by the camera. See Supprted License Plates fr mre infrmatin. Pre-Event Recrd Time: enter the amunt f time that vide is recrded befre the license plate is recgnized. Pst-Event Recrd Time: enter the amunt f time that vide is recrded after the license plate is recgnized. Minimum Cnfidence: mve the slider t set the minimum cnfidence fr a detected license plate t be recgnized. The default value is 80%. Enable this lane: select this check bx t enable LPR n this lane. 5. Mve and adjust the size f the green verlay t define the area where license plates are detected by the camera. 6. Click OK. Nte: The maximum size f the license plate recgnitin area is ne megapixel. The green verlay autmatically adjusts itself t meet the size limits. Cnfiguring the Watch List The License Plate Recgnitin (LPR) Watch List identifies license plates that are f special interest. When a license plate n the Watch List is detected, an event is generated t ntify yu f the license plate and the event can be used t trigger an actin in the Rules engine. Yu can manually add each license plate that needs t be recgnized, r imprt a list f licenses int the applicatin. Adding Licenses t the Watch List 1. Right-click a server in the System Explrer then select Setup t pen the server Setup dialg bx. See Accessing the Server Setup fr mre infrmatin. 2. Click License Plate Recgnitin. 3. When the License Plate Recgnitin dialg bx appears, select the Watch List tab. 62

71 Setup Figure A. License Plate Recgnitin dialg bx: Watch List tab 4. Click Add. The Add License Plate dialg bx appears. Figure B. Add License Plate dialg bx 5. Enter the license plate number. 6. Mve the Minimum Cnfidence slider t determine hw similar the detected license plates must be befre it is cnsidered a match. 63

72 Avigiln Cntrl Center Enterprise Client User Guide Fr example, if a license plate n yur watch list is ABC 123 and Avigiln detects an ABC 789 license plate, the system will be 50% cnfident that it has fund a match. If the system detects ABC 129, it will be 83% cnfident that it has fund a match. 7. Click OK. Deleting a License Plate frm the Watch List 1. In the License Plate Recgnitin dialg bx, select the Watch List tab. 2. Select the license frm the Watch List, and click Delete. Exprting a Watch List 1. In the License Plate Recgnitin dialg bx, select the Watch List tab. 2. Click Exprt. 3. In the Save As dialg bx, name the file and click Save. The Watch List can be exprted as a text file r a cmma-separated values (CSV) file. Imprting a Watch List 1. In the License Plate Recgnitin dialg bx, select the Watch List tab. 2. Click Imprt. 3. In the Imprt dialg bx, lcate the Watch List file and click Open. Scheduling Server Events Server events are actins triggered within the Avigiln Cntrl Center Server that are nt related t vide recrding, like ntificatins. When yu cnfigure a server event, yu are given the ptin t assign a schedule fr the event. Schedules cntrl when events are enabled at specific times during a day r nly n specific days. When yu arrive at the scheduling page while cnfiguring an event, yu have the ptin t select an existing schedule r create a new schedule. Figure A. Schedule ptin 1. T use a cnfigured schedule, select an ptin frm the drp dwn list. The default ptin is Always, which allws the event t run cnstantly. 2. T create r edit a schedule, click. 64

73 Setup Figure B. Edit Schedules dialg bx. a. T add a new schedule, click Add then enter a name fr the new schedule. b. T edit a schedule, select a schedule frm the list and make the required changes. c. In the Start and End fields, enter the time the event is enabled fr. d. In the Start Date field, enter when the schedule wuld begin. e. In the Recurrence Pattern area, select hw ften yu want the event t be enabled Optin Daily Weekly Mnthly Yearly Descriptin The event wuld be enabled every day at the same time. Select the number f days between each schedule recurrence. The event wuld be enabled every week at the same day(s) and time. Select the day(s) f the week, then select the number f weeks between each schedule recurrence. The event wuld be enabled nce a mnth at the same day and time. Select the specific day r weekday, then select the number f mnths between each schedule recurrence. The event wuld be enabled nce a year at the same day and time. Select the specific day r weekday and mnth, then select the number f years between each schedule recurrence

74 Avigiln Cntrl Center Enterprise Client User Guide Click OK. Camera Setup The camera Setup dialg bx is respnsible fr all the features that cntrl cameras and the devices that can be cnnected t cameras. Refer t any f the fllwing sectins t access and cnfigure the camera setup. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Accessing the Camera Setup Perfrm ne f the fllwing steps t pen the camera Setup dialg bx: Select Tls > Setup... then select the camera yu want t setup frm the left pane. In the System Explrer pane, right-click the camera and select Setup. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. 66

75 Setup Figure A. Camera Setup dialg bx General Use the camera General dialg bx t set the camera's identity and cnfigure the camera's PTZ settings. Yu can als rebt the camera thrugh the General dialg bx. Setting the Camera's Identity In the camera General dialg bx, yu can give the camera a name, describe the camera's lcatin, and give the camera a lgical ID. The lgical ID is needed t use the select camera keybard cmmand. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 67

76 Avigiln Cntrl Center Enterprise Client User Guide 2. Click General. The General dialg bx is displayed. Figure A. General dialg bx 3. In the Camera Name field, give the camera a meaningful name t help yu identify the camera. By default, the camera mdel number is used as the camera's name. 4. In the Camera Lcatin field, describe the camera's lcatin. 5. In the Lgical ID field, enter a unique number t allw applicatins and integratins t identify this camera. 6. T disable the LEDs n the camera, select the Disable camera status LEDs. This may be required if the camera is installed in a cvert lcatin. 7. If the camera has a mtrized zm and fcus lens, the Enable PTZ Cntrls check bx is displayed. When selected, users can cntrl the camera's zm and fcus thrugh the PTZ Cntrls pane. See Cntrlling PTZ Cameras fr mre infrmatin. 8. Click OK. Cnfiguring PTZ Use the camera General dialg bx t enable and cnfigure the pan, tilt, zm (PTZ) features fr Avigiln cameras. PTZ devices are cnnected t Avigiln cameras thrugh the RS-485 inputs. Third party PTZ cameras cannt be cnfigured thrugh the Avigiln Cntrl Center. 68

77 Setup 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click General. The General dialg bx appears. 3. In the PTZ area, select the Enable PTZ check bx. Nte: If the fllwing ptins are nt displayed, the camera nly has a mtrized zm and fcus lens and cannt perfrm full PTZ. Selecting the Enable PTZ Cntrls check bx will allw users t cntrl the zm and fcus thrugh the PTZ Cntrls pane. 4. In the Prtcl drp dwn list, select the apprpriate PTZ prtcl. The available prtcls include: American Dynamics Sensrmatic AXSYS AXSYS DCU Ernitec ERNA Hneywell Diamnd Kalatel ASCII Pelc D Pelc P TEB Ligne Vicn extended Vicn nrmal Videtec Legacy Videtec MACRO 5. Enter the Dip Switch Address, Baud Rate and Parity fr the PTZ device. 6. Click OK. Rebting the Camera Yu can restart all Avigiln cameras thrugh the camera's General dialg bx. This feature is nt available fr third party cameras. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 69

78 Avigiln Cntrl Center Enterprise Client User Guide 2. Click General. The General dialg bx appears. 3. Click Rebt Camera. The camera discnnects frm the Avigiln Cntrl Center and shuts dwn. When the camera starts up again, the camera shuld autmatically recnnect with the Avigiln Cntrl Center. Netwrk Use the camera Netwrk dialg bx t change hw a camera cnnects t the server netwrk. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Changing Camera Netwrk Settings 1. Right-click the camera and select Setup t pen the camera Setup dialg bx. 2. Click Netwrk. 3. In the Netwrk dialg bx, select hw the camera btains an IP address: Figure A. Netwrk dialg bx 70

79 Setup Obtain an IP address autmatically: select this ptin fr the camera t cnnect t the netwrk thrugh an autmatically assigned IP address. The camera will attempt t btain an address frm a DHCP server. If it cannt, the camera will default t addresses in the x.x range. Use the fllwing IP address: select this ptin t manually assign a static IP address fr the camera. Enter the IP Address, Subnet Mask and Gateway yu want the camera t use. 4. Select the Cntrl Prt fr cnnecting t the camera. This prt is als used fr manually discvering the camera n the netwrk. 5. Select the Enable Multicast check bx t enable multicast streaming frm the camera. Yu must enable multicast t set up redundant cnnectins t multiple servers. Use the default generated IP Address, TTL and Base Prt, r enter yur wn values. 6. Click OK. Image and Display Use the Image and Display dialg bx t cntrl a camera s display settings fr live and recrded vide. Changing Image and Display Settings Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Image and Display. 3. In the Image and Display dialg bx, make the required changes t adjust the camera's image settings. A preview f yur changes are displayed in the image panel. Tip: Use the Maximum Expsure, Maximum Gain and Pririty ptins t cntrl lw light behavir. 71

80 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Image and Display dialg bx Optin Expsure Descriptin Yu can allw the camera t cntrl the expsure by selecting Autmatic, r yu can set a specific expsure rate. Nte: Increasing the manual expsure time may affect the image rate. Iris IR Cut Filter Flicker Cntrl Backlight Cmpensatin Maximum Expsure Yu can allw the camera t cntrl the iris by selecting Autmatic, r yu can manually set it t Open r Clsed. Yu can allw the camera t cntrl the infrared cut filter by select Autmatic, r set the camera t Clr r Mnchrme mde. If yur vide image flickers because f the flurescent lights arund the camera, yu can reduce the effects f the flicker by setting the Flicker Cntrl t the same frequency as yur lights. Generally, Eurpe is 50Hz and Nrth America is 60Hz. If yur scene has areas f intense light that cause the verall image t be t dark, mve the Backlight Cmpensatin slider until yu achieve a well expsed image. Yu can limit the autmatic expsure setting by selecting a maximum 72

81 Setup expsure level. By setting a maximum expsure level fr lw light situatins, yu can cntrl the camera's expsure time t let in the maximum amunt f light withut creating blurry images. Maximum Gain Pririty Saturatin Sharpening Image Rtatin White Balance Yu can limit the autmatic gain setting by selecting a maximum gain level. By setting a maximum gain level fr lw light situatins, yu can maximize the detail f an image withut creating excessive nise in the images. Yu can set Image Rate r Expsure as the pririty. When set t Image Rate, the camera will maintain the set image rate as the pririty, and will nt adjust the expsure beynd what can be recrded fr the set image rate. When set t Expsure, the camera will maintain the expsure setting as the pririty, and will verride the set image rate t achieve the best image pssible. Yu can adjust the vide's clr intensity by mving the Clr Saturatin slider until the vide image meets yur requirements. Yu can adjust the vide sharpness t make the edges f bjects mre visible. Mve the Sharpening slider until the vide image meets yur requirements. Yu can change the rtatin f captured vide. Yu can rtate the vide 90, 180 r 270 degrees clckwise. Yu can cntrl white balance settings t adjust fr differences in light. Yu can allw the camera t cntrl the white balance by selecting Autmatic, r select Custm and manually set the Red and Blue settings. 4. T fcus the camera, see Fcusing the Camera Lens. 5. Click Apply t Cameras... t apply the same settings t ther cameras f the same mdel. 6. Click OK. Zming and Fcusing the Camera Lens If yu have a camera with a lens capable f electrnic zm and fcus, yu can zm and fcus the camera thrugh the Image and Display dialg bx. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. 73

82 Avigiln Cntrl Center Enterprise Client User Guide 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Image and Display. The Image and Display dialg bx appears. 3. If the camera has a built-in aut fcus feature, yu can chse ne f the fllwing: Cntinuus Fcus: the camera will autmatically fcus itself whenever the scene changes. Skip the fllwing step. Manual Fcus: yu can manually fcus the camera thrugh the Image and Display Fcus buttns. Once the fcus is manually set, it will nt change. 4. While yu view the camera image panel, cmplete the fllwing steps t zm and fcus the camera: Tip: Fr Avigiln HD Prfessinal cameras, the lens must be set t aut-fcus (AF) mde n the camera. If the camera des nt detect the lens, the Fcus buttns are nt displayed. 3. a. Use the Zm buttns t zm in t the distance yu want t fcus. b. In the Iris drp dwn list, select Open. When the iris is fully pen, the camera's depth f field is the shrtest. c. Use the Fcus buttns until the image becmes clear. Buttn Descriptin The camera will autmatically fcus nce. Fcused as clse t zer as pssible Large step tward zer Small step tward zer Small step tward infinity Large step tward infinity Infinity 74

83 Setup 4. Click Apply t Cameras... t apply the same settings t ther cameras f the same mdel. 5. Click OK. Cmpressin and Image Rate Use the camera Cmpressin and Image Rate dialg bx t mdify the camera's cmpressin and image quality settings fr sending image data ver the netwrk. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Changing Cmpressin and Image Rate Settings 1. Right-click the camera in the System Explrer then select Setup t pen the camera setup dialg bx. 2. Click Cmpressin and Image Rate. The Cmpressin and Image Rate dialg bx appears. Figure A. Cmpressin and Image Rate dialg bx. The Bandwidth area gives an estimate f the bandwidth used by the camera with the current settings. Adjust the settings as required. Nte: Fr cameras capable f maintaining multiple streams, the settings in this dialg bx nly affect the primary stream. 3. In the Frmat drp dwn list, select the preferred streaming frmat. 75

84 Avigiln Cntrl Center Enterprise Client User Guide 4. In the Image Rate bar, mve the slider t select the hw many images per secnd (ips) yu want the camera t stream ver the netwrk. 5. In the Image Quality drp dwn list, select the desired image quality number. Image quality setting f 1 will prduce the highest quality vide and require the mst bandwidth. 6. In the Max Bit Rate drp dwn list, select the maximum bandwidth the camera can use in kilbits per secnd (kbps). 7. In the Reslutin drp dwn list, select the preferred image reslutin. 8. In the Keyframe Interval drp dwn list, enter the preferred number f frames between each keyframe. 9. If yur camera supprts multiple vide streams, yu can select the Enable secndary live viewing stream check bx. When enabled, the secndary live viewing stream is a lwer reslutin vide stream that is autmatically displayed when yu mnitr live vide n a netwrk that des nt have enugh bandwidth t display the primary live viewing stream. 10. Click Apply t Cameras... t apply the same settings t ther cameras f the same mdel. 11. Click OK. Image Dimensins Use the Image Dimensin dialg bx t set the image dimensins fr the camera. Yu can crp the vide image t help reduce bandwidth and increase the maximum image rate. Changing Image Dimensins Settings 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Image Dimensins. 3. In the Image Dimensins dialg bx, adjust the image dimensins by perfrming ne f the fllwing: Drag the edges f the image until the vide is crpped t fit yur requirements. Change the values fr the Tp, Left, Width, and Height field. 76

85 Setup Figure A. Image Dimensins dialg bx 4. Click OK. Mtin Detectin In the Mtin Detectin dialg bx, yu can define specific mtin detectin areas and cnfigure the camera's sensitivity and threshld fr mtin. Selecting an Area t Detect Mtin In the Mtin Detectin dialg bx, yu can define the green mtin detectin areas in the camera's field f view. Mtin detectin is ignred in the areas nt highlighted in green. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Mtin Detectin. 3. In the Mtin Detectin dialg bx, use the tls abve the image panel t define the green mtin detectin area: Set Area: select this buttn then draw green rectangles t define the mtin detectin areas. Yu can draw multiple rectangles t create yur mtin detectin area. 77

86 Avigiln Cntrl Center Enterprise Client User Guide Clear Area: select this buttn and draw rectangles t erase sectins frm the mtin detectin area. Draw: select this buttn and manually draw mtin detectin areas with yur muse. This tl allws yu t be very specific and highlight unusual shapes. Set All: click this buttn t highlight the entire image panel fr mtin detectin. Clear All: click this buttn t clear the image panel f mtin detectin areas. Figure A. Mtin Detectin dialg bx 4. Click OK. T define the sensitivity and threshld fr the mtin detectin area, see Cntrlling Mtin Sensitivity and Threshld. Cntrlling Mtin Sensitivity and Threshld In the Mtin Detectin dialg bx, yu can cntrl the camera's sensitivity and threshld fr mtin. Yu can als define hw much time shuld be recrded befre and after each mtin event. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Mtin Detectin. The Mtin Detectin dialg bx appears. 78

87 Setup 3. Mve the Sensitivity slider t adjust hw much each pixel must change befre it is cnsidered in mtin. The higher the sensitivity, the smaller the amunt f pixel change is required befre mtin is detected. 4. Mve the Threshld slider t adjust hw many pixels must change befre the image is cnsidered t have mtin. The higher the threshld, the higher the number f pixels must change befre the image is cnsidered t have mtin. Tip: The Mtin indicatr abve the Threshld slider will mve t indicate hw much mtin is ccurring in the current scene. Only when the mtin indicatr mves t the right f the Threshld marker will the camera nte the mtin. 5. In the Pre-Mtin Recrd Time and Pst-Mtin Recrd Time bxes, specify hw lng vide is recrded befre and after the mtin event. 6. Click OK. Privacy Znes Yu can set privacy znes in the camera's field f view t blck ut areas that yu d nt want t see r recrd. Adding a Privacy Zne Nte: Yu can add n mre than 4 privacy znes per camera. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Privacy Znes. 3. In the Privacy Znes dialg bx, click Add and a green bx will appear n the image panel. 79

88 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Privacy Znes dialg bx 4. Mve and resize the green bx until it cvers the area yu want t blck ut. 5. If yu are adding privacy znes t a PTZ camera, the fllwing tw ptins are displayed abve the image panel. Select this ptin t enable PTZ mde. PTZ mde allws yu t pan and tilt the camera field f view t where the privacy zne needs t be. Fr details n hw t use the pan and tilt cntrls, see Cntrlling PTZ Cameras. Select this ptin t disable PTZ mde. 6. Click OK. Editing and Deleting a Privacy Zne 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 80

89 Setup 2. Click Privacy Znes. 3. In the Privacy Znes dialg bx, select a privacy zne frm the Privacy Zne list and perfrm ne f the fllwing: T edit the privacy zne, adjust the green bx n the image. T delete the privacy zne, click Delete. 4. Click OK. Manual Recrding Yu can manually set a camera t recrd events utside f the camera's recrding schedule. Manual recrding can nly be activated when viewing live vide. See Triggering Manual Recrding fr mre infrmatin. Use the Manual Recrding dialg bx t define the maximum manual recrding time fr each camera. Changing Manual Recrding Settings 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Manual Recrding. The Manual Recrding dialg bx appears. Figure A. Manual Recrding dialg bx 3. Specify the fllwing: Manual Recrding Duratin: enter hw lng the camera shuld recrd fr if recrding is nt manually stpped. Pre-Trigger Recrd Time: enter the amunt f time vide is recrded befre manual recrding is activated. 4. Click Apply t Cameras... t apply the same settings t ther cameras f the same mdel. 5. Click OK. 81

90 Avigiln Cntrl Center Enterprise Client User Guide Digital Inputs and Outputs Use the Digital Inputs and Outputs dialg bx t set up external digital input and utput devices that are cnnected t the camera. The external devices can be used t create alarms r trigger recrding events and specific actins thrugh the rules engine. See Rules fr mre infrmatin. Setting Up Digital Inputs 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Digital Inputs and Outputs. 3. In the Digital Inputs area, select an input. 82

91 Setup Figure A. Digital Inputs and Outputs dialg bx: Digital Inputs Settings 4. Enter a name t identify the digital input. 5. In the Recrding Duratin area, select ne f the fllwing: Select Fllw Event t recrd the entire digital input event. Select Maximum Time t limit the recrding time. 6. Enter hw lng vide is recrded befre and after the digital input event. 7. Select the digital input's default Circuit State. 8. Select the cameras that shuld be linked t this digital input. If the Recrding Schedule is cnfigured t recrd digital inputs, the cameras selected in the Link t Camera(s) area are used t recrd all the events triggered by this digital input. 9. Click OK. Setting Up Digital Outputs Once a digital utput is cnfigured, yu can manually trigger the digital utput in an image panel. See Triggering Digital Output fr mre infrmatin. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Digital Inputs and Outputs. 3. In the Digital Outputs area, select an utput. 83

92 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Digital Inputs and Outputs dialg bx: Digital Output Settings 4. Enter a name t identify the digital utput. 5. Select the digital utput's default Circuit State. 6. The Trigger Behavir ptins define what ccurs when the digital utput is activated. Select Activate t enable the digital utput in cntinuus mde. The Duratin fields allw yu t specify hw lng the digital utput shuld be active fr. Select Pulse t enable the digital utput in pulse mde. Specify the Perid, Duty Cycle, and Repeat Cunt fr the pulse. 7. Select the cameras that shuld be linked t this digital utput. When the digital utput is triggered, all the cameras linked t this digital utput begin recrding. 8. Click OK. 84

93 Setup Micrphne Nte: Audi recrding requires an Audi Channel License. Use the Micrphne dialg bx t change the settings fr any audi input devices that are cnnected t the camera. Yu can als link the audi t ther cameras. T use this feature, a micrphne must be cnnected t the camera. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Changing Micrphne Settings 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Micrphne. The Micrphne dialg bx appears. 85

94 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Micrphne dialg bx 3. Select the Enable check bx t enable audi recrding frm micrphnes cnnected t the camera. Nte: An errr message will appear if yu d nt have an Audi Channel License. 4. Enter a name fr the micrphne. 5. In the Surce drp dwn list, select the audi input surce. 6. In the Gain drp dwn list, select the amunt f analg gain that is applied t the audi input. The higher the db setting, the luder the vlume. 7. Click Listen t test the settings and listen t the audi input device. 8. In the Link t Camera(s) area, select the cameras that shuld be linked t this audi. 9. Click OK. Speaker Nte: Audi bradcasting requires a Speaker Channel License. Use the Speaker dialg bx t change the settings fr any speakers that are cnnected t the camera. Yu can als link the audi t ther cameras. T use this feature, speakers must be cnnected t the camera and a micrphne must be cnnected t yur lcal client. Nte: The dialg bx may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Changing Speaker Settings 1. Right-click the camera in the System Explrer then select Setup t pen the camera Setup dialg bx. See Accessing the Camera Setup fr mre infrmatin. 2. Click Speaker. The Speaker dialg bx appears. 86

95 Setup Figure A. Speaker dialg bx 3. Select the Enable check bx t enable audi bradcasting. Speakers cnnected t the camera wuld bradcast audi frm the micrphne that is cnnected t the lcal client. Nte: An errr message will appear if yu d nt have a Speaker Channel License. 4. Select the Recrd Speaker check bx t recrd what is bradcast. 5. Enter a name fr the speaker. 6. The Vlume slider cntrls the vlume f the speakers. 7. In the Link t Camera(s) area, select the cameras that shuld be linked t the speakers. 8. T test the micrphne level, speak int the micrphne. The red bar will mve t shw the audi input level. 9. Click OK. If yu want t enable tw-way audi, see Micrphne in the client setup sectin. 87

96 Avigiln Cntrl Center Enterprise Client User Guide Client Setup The client Setup dialg bx is respnsible fr all the Avigiln Cntrl Center features that are cnfigured and stred n the lcal client cmputer. Refer t any f the fllwing sectins t access and cnfigure the client setup. Accessing the Client Setup Perfrm ne f the fllwing steps t pen the client Setup dialg bx. Select Tls > Setup... and select the lcal client frm the left pane. In the System Explrer, right-click the lcal client and select Setup. Figure A. Setup Lcal Client dialg bx 88

97 Setup General Use the client General dialg bx t change yur lcal applicatin preferences. Changing General Client Settings 1. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 2. Click General. 3. In the General dialg bx, make any required changes: Figure A. General dialg bx Save/restre windw layut: select this check bx if yu want the applicatin t remember yur layut preferences. Autmatically launch full screen: select this check bx if yu want the applicatin t autmatically launch in full screen each time it starts. Display n-screen messages: select this check bx if yu want the applicatin t display event ntificatin messages thrugh the Event pp-up dialg bx. Event ntificatins include license plate recgnitin events, system events and rule events. If the check bx is cleared, all event ntificatins are hidden. 89

98 Avigiln Cntrl Center Enterprise Client User Guide Cycle dwell time: enter the number f secnds the applicatin waits befre it cycles t a different View. See Cycling Thrugh Views fr mre infrmatin. Language: select a language frm the drp dwn list t change the applicatin language. Select Windws Default fr the applicatin t autmatically display the same language as the lcal client. Autmatically lg in t servers: select this check bx t autmatically lg int all servers that are available n the netwrk. Select the type f lgin yu use: Windws Authenticatin yur Windws lgin; r Using saved user name and passwrd yur Avigiln Cntrl Center username and passwrd. In the Maximum Incming Client Bandwidth area, yu can set hw much bandwidth is allwed t cme int the client. This wuld include vide streaming. 4. Click OK. Select Unlimited, r select Other and specify the maximum kilbits per secnd (kbits/s) yu want t allw. Jystick Tw types f jysticks are supprted: standard Micrsft DirectX USB Jysticks and the Avigiln Prfessinal Jystick Keybard. Use the Jystick dialg bx t cnfigure the jystick settings. Cnfiguring a Standard USB Jystick Use the Jystick dialg bx t cnfigure the buttns used in yur standard Micrsft DirectX USB jystick. 1. Cnnect the jystick. 2. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 3. Click Jystick. 4. If the jystick is nt autmatically detected, an errr message will appear. Click Scan fr Jysticks... Nte: The errr message will nt appear if the jystick was detected. When the jystick is detected, the Jystick dialg bx appears. 90

99 Setup Figure A. Jystick dialg bx 5. Set up an actin fr each buttn n the jystick: 6. Click OK. a. Press a buttn n the jystick and the buttn label is highlighted in the Jystick dialg bx. b. Select an actin fr the buttn frm the drp dwn list. c. Repeat this prcedure fr each buttn n the jystick. Cnfiguring an Avigiln Prfessinal Jystick Keybard The Avigiln Prfessinal Jystick Keybard is a USB add-n that cntains a jystick fr cntrlling zm and pan within image panels, a jg shuttle fr cntrlling the Timeline, and a keypad prgrammed with the applicatin's keybard cmmands. Refer t Keybard Cmmands fr the keypad cmmands that cntrl the applicatin. By default, the keybard is installed in right-hand mde. Use the Jystick dialg bx t cnfigure left-hand mde. 1. Cnnect the keybard. 2. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 3. Click Jystick. 91

100 Avigiln Cntrl Center Enterprise Client User Guide 4. If the keybard is nt autmatically detected, an errr message will appear. Click Scan fr Jysticks... Nte: The errr message will nt appear if the keybard was detected. When the keybard is detected, the Jystick dialg bx appears. Figure A. Jystick dialg bx 5. Select the Enable left-hand mde check bx. 6. Click OK. The keybard is nw cnfigured fr left-hand mde. Rtate the keybard until the jystick is n the left and the jg shuttle is n the right. Reinstall the keypad cver with the View buttn labels at the tp. Exprting Settings Yu can exprt yur persnalized settings frm the lcal client s that the settings can be backed up r used n a different cmputer. These settings include general client settings, jystick, maps, saved Views, web pages and Site View. T exprt server settings like Recrding Schedules, Users & Grups, POS Surce and Device Cnnectin settings, see the Avigiln Cntrl Center Server User Guide. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Exprting Client Settings 1. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 2. Click Exprt Settings. 92

101 Setup 3. Select the settings yu want t exprt. Figure A. Exprt Settings dialg bx The General settings include display quality, deinterlacing, manually added servers, image verlays, and client cnnectin speed. 4. Click OK. 5. In the Save As dialg bx, name and save the file. Exprted client settings can nly be saved in Avigiln Client Settings File (.avc) frmat. Imprt Settings Imprt and use settings that were previusly exprted frm the lcal client r frm a different cmputer. Nte: The imprted settings will verwrite the lcal client's current settings. Imprting Client Settings 1. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 2. Click Imprt Settings. 3. In the Select File t Imprt Frm dialg bx, find the Avigiln Client Settings File (.avc) yu want t imprt then click Open. 4. Select the settings yu want t imprt. 93

102 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Imprt Settings dialg bx 5. Click OK. Micrphne If yu have a micrphne and speaker channel license, yu have the ptin f enabling a tw-way audi system. This allws peple in the vide t talk with the peratr mnitring the vide. Yu have the ptin f full-duplex audi, which allws simultaneus cmmunicatin, r half-duplex, which nly allws cmmunicatin frm ne side at a time. 1. Right-click the lcal client in the System Explrer then select Setup t pen the client Setup dialg bx. Fr mre infrmatin, see Accessing the Client Setup. 2. Click Micrphne. The Micrphne dialg bx appears. Figure A. Micrphne dialg bx Select the Full-duplex Audi ptin t enable tw-way audi. 94

103 Setup Select the Half-duplex Audi ptin t use the micrphne and speakers separately. 3. Click OK. Fr mre infrmatin abut the audi features, see Micrphne and Speaker in the camera setup sectin. 95

104 Site View What is Site View? Site View is a way t custmize the way cameras and servers are displayed in the System Explrer. The System Explrer is where all the servers and cameras are rganized fr easy access. The System Explrer is able t rganize yur surveillance system in tw ways: Server View and Site View. Server View lists all the servers yu have access t, and all the cameras and encders that are cnnected t each server. Server View als gives yu quick access t yur maps, web pages, and saved Views. Site View allws yu t custmize the way servers, cameras, encders, maps, saved Views and web pages are displayed in the System Explrer. Yu can rganize the cameras by lcatin, r nly display maps f the surveillance site. Accessing Site View Site View allws yu t custmize the System Explrer display. The default Server View lists all the cameras n the netwrk by the server they are cnnected t. This may nt be lgical fr yur surveillance site, s yu can create a Site View that reflects yur surveillance requirements. Fr example, yu can create a Site View that mimics the layut f each flr in yur building. T access Site View, select Site View frm the System Explrer drp dwn list. Figure A. System Explrer If yu have nt created a Site View, yu will be prmpted t set up a new Site View. Click Yes then see Adding a Site fr mre infrmatin. 96

105 Site View Adding a Site 1. Select File > Edit Site View... t pen the Edit Site View dialg bx. If yu try t access the System Explrer Site View befre a site has been added, yu will be prmpted t set up a new site. Click Yes t pen the Edit Site View dialg bx. Figure A. Edit Site View dialg bx 2. If yu are adding a new Site View, select and rename the New Site that has been added fr yu. 3. T add a new site, click Add Site t create a new site t grup items under. Select and rename the New Site. 4. In the Server View pane, select any f the listed items and click Add. Nte: Only the servers yu are lgged int are displayed. 5. Once the selected item has been added t the Site View pane, use the green arrws t psitin the item within yur Site View. 6. Select an item in the Site View pane and click Remve t remve the item frm yur Site View. 7. When yur Site View is cmplete, click OK. 97

106 Avigiln Cntrl Center Enterprise Client User Guide Editing and Deleting a Site Whenever yur site requirements change, yu can edit r delete the Site View. 1. Select File > Edit Site View t pen the Edit Site View dialg bx. 2. In the Edit Site View dialg bx, perfrm ne f the fllwing: T edit the Site View, make the required changes then click OK. Refer t Adding a Site fr details abut the editable ptins. T delete the entire Site View, select each site and click Remve. When there are n sites listed in the Site View, click OK. Next time yu try t pen Site View in the System Explrer, yu will be prmpted t create a new Site View. 98

107 Views What are Views? A View is a tab cmpsed f image panels that allws yu t rganize hw vide is displayed. Fr example, yu can chse t display vide frm multiple cameras at the same time by using different layuts. Adding and Remving a View Views allw yu t custmize hw yu mnitr vide. Yu can add a new View t an existing windw r pen a new View in its wn windw t make use f multiple mnitrs. Views can als be remved as required. Adding a New View t the Applicatin Windw Perfrm ne f the fllwing: Select File > New View. Frm the tlbar, click the New View buttn. Adding a View t a New Windw Perfrm ne f the fllwing: Select File > New Windw. 99

108 Avigiln Cntrl Center Enterprise Client User Guide Frm the tlbar, click the New Windw buttn. A new windw appears. Yu can nw psitin this windw t make use f multiple mnitrs. Clsing a View frm the Applicatin Windw Perfrm ne f the fllwing: Select File > Clse View. On the View tab, click the Clse View buttn. Clsing a Windw Perfrm ne f the fllwing: Select File > Clse Windw. Click the Clse buttn n the tp right crner f the windw. View Layuts Yu can rganize hw vide is displayed thrugh View layuts. Yu can chse t display vide frm a different camera in each image panel, r display vide frm the same camera at different zm levels. There are 10 pre-cnfigured layuts that yu can edit t fit yur needs. Selecting a Layut fr a View Yu can rganize hw vide is displayed by selecting a View layut. The figure shws the default View layuts. Select View > Layuts > # Divisin. On the tlbar, select the Change Layut buttn then select ne f the layut ptins. 100

109 Views Figure A. Layuts n the tlbar Editing a View Layut If the default View layuts d nt fit yur surveillance requirements, yu can custmize a View layut. 1. On the tlbar, select the Change Layut buttn then select Edit Layuts. 101

110 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Layuts n the Tlbar 2. In the Edit Layuts dialg bx, select the layut yu want t change. 3. Enter the number f Clumns and Rws yu want in yur layut. 4. In the layut diagram, d any f the fllwing t further custmize the layut. 102

111 Views Figure B. Edit Layuts dialg bx T create a larger image panel, select a grey line t delete the brder between tw image panels. When a line is highlighted in red, the line can be deleted. T restre an image panel, select a dtted line t divide a large image panel int tw. When a dtted line is highlighted in green, the line can be restred. T restre all default View layuts, click Restre Defaults. All custm layuts in the Layuts list will be replaced. Nte: Yu can nly add r subtract lines t create a rectangular shape. 5. Click OK t save yur changes. The previus View layut has been replaced with yur custmized layut. Tip: The keybard cmmands used t access View layuts are linked t the layut's psitin n the View Layuts list. Fr example, if yur custm layut is placed at the tp f the Layuts list (layut 1), yu can press Alt + 1 t use that layut. Making a View Full Screen Yu can maximize a View t make full use f a mnitr. 103

112 Avigiln Cntrl Center Enterprise Client User Guide On the tlbar, click Full Screen. Ending Full Screen On the tlbar at the tp left f the screen, click End Full Screen. Tip: The tlbar is hidden when the applicatin is idle. Mve yur muse t display the tlbar. Cycling Thrugh Views Once yu have multiple Views setup, yu can cycle thrugh the Views by displaying each ne fr a few secnds. This is useful when mnitring a large number f cameras. 1. Activate the Cycle Tab feature: Frm the View menu, select Cycle Views. On the tlbar, click Cycle Views. T change the cycle dwell time, see Changing General Client Settings fr mre infrmatin. Saving a View Once yu've set up a View yu like, yu can save the View fr use again in the future. A saved View remembers the current View layut, the cameras displayed in each image panel, and the image panel display settings. Saving a View 1. Select File > Save View. 2. In the Save As dialg bx, name the View and click OK. Yur saved view will appear in the System Explrer. 104

113 Views Figure A. Saved Views Opening a Saved View Perfrm ne f the fllwing In the System Explrer, right-click the saved View and select Open. Drag the saved View frm the System Explrer t the current View in the applicatin r new windw. Renaming a Saved View 1. In the System Explrer, right-click the saved View and select Rename. 2. In the Rename View dialg bx, enter a new name and click OK. Deleting a Saved View 1. In the System Explrer, right-click the saved View and select Delete. 2. In the cnfirmatin dialg bx, click Yes. 105

114 Maps A map is a digital cpy f yur physical surveillance site. Yu can add cameras, encders, servers, saved Views, and ther maps t yur map t help yu quickly navigate thrugh yur surveillance site. T watch a vide verview f the Maps feature, see the Wrking with Maps and Web Pages training vide in the Avigiln Training Center. Using a Map Yu can pen a map in any image panel, and pen vide r alarms frm the map. 1. T pen a map in an image panel, perfrm ne f the fllwing: Duble-click a map frm the System Explrer. Drag the map frm the System Explrer t an image panel. In the System Explrer, right-click the map and select Add t View Figure A. System Explrer: Maps List 2. When the map appears in an image panel, perfrm any f the fllwing: 106

115 Maps Figure B. Map in an image panel. T... Review an alarm Display vide frm a camera n the map Open a linked map Open a linked View D this... When a camera flashes in red, the alarm linked t the camera has been triggered. Click the camera t mnitr the live alarm vide. Drag a camera frm the map t an image panel. Click the camera n the map. Click the map icn n the map. Yu can use the Frward and Back buttns t mve between maps. Click the saved View n the map. 107

116 Avigiln Cntrl Center Enterprise Client User Guide Adding a Map Yu can create a map frm any image in JPEG, BMP, PNG, r GIF frmat. The image is used as the map backgrund and cameras are added n tp t shw where they are lcated in yur surveillance site. 1. T start a new map, perfrm ne f the fllwing: Frm the File menu, select New Map. In the System Explrer, right-click the Maps icn, and select New Map. 2. In the Select Map Image dialg bx, lcate yur map image and click Open. 3. In the Map Name field, enter a name fr the map. 4. In the Editing: Map tab, drag and place cameras frm the System Explrer nt the map. Figure A. Editing: Map tab By default a camera is displayed as an icn with a yellw triangle t represent its field f view. 108

117 Maps 5. Drag encders, servers, saved Views and ther maps that yu need frm the System Explrer nt the map. 6. In the Map Icn Prperties bx, yu can change the way icns are displayed n the map. Select any icn n the map and perfrm the fllwing: Figure B. Camera icn prperties Click Save. a. T replace an icn with a clickable shape regin, select ne f the shape buttns. Yu can replace the icn with a rectangle, ellipse, r plygn regin. b. Select the Shw name check bx t display the bject's name n the map. c. Click Delete frm Map t remve the bject frm the map. d. (Cameras nly) Select the Shw field f view check bx t display the camera's yellw field f view. Drag the crners f the yellw triangle t expand the field f view. Drag the black circle at the end f the triangle t rtate the field f view. e. (Cameras nly) Click Change Image Regin... t change the vide regin that is linked t the camera n the map. In the Change Image Regin dialg bx, change the size and psitin f the green verlay then click OK. Editing and Deleting a Map Yu can update a map r delete an ld map anytime. 1. In the System Explrer, right-click a map then select ne f the fllwing: 109

118 Avigiln Cntrl Center Enterprise Client User Guide Figure A. System Explrer: Maps list T edit the map, select Edit. Refer t Adding a Map fr details abut the editable ptins. T delete the map, select Delete. When the cnfirmatin dialg bx appears, click Yes. 110

119 Web Pages Yu can review nline cntent while mnitring vides in a View by adding web pages t the Avigiln Cntrl Center. T watch a vide verview f the web pages feature, see the Wrking with Maps and Web Pages training vide in the Avigiln Training Center. Nte: Internet acceses is required t use web pages. Using a Web Page T pen a web page, perfrm ne f the fllwing Duble-click a web page in the System Explrer. Drag the web page frm the System Explrer t an image panel. In the System Explrer, right-click the web page and select Add t View. Figure A. Saved web pages The web page is displayed in ne f the image panels. Use the web brwser buttns t navigate thrugh the internet. Figure B. Web page image panel buttns. 111

120 Avigiln Cntrl Center Enterprise Client User Guide Adding a Web Page Yu can add web pages fr quick access t internet cntent that is linked t yur surveillance system. 1. T pen the Add Web Page dialg bx, perfrm ne f the fllwing: Frm the File menu, select New Web Page. In the System Explrer, right-click the Web Pages icn then select New Web Page. Figure A. Add Web Page dialg bx 2. Enter a name fr the web page. 3. Enter the web page URL in the Lcatin field. 4. Select a Zm Level fr viewing the web page inside an image panel. 5. Click OK. Editing and Deleting a Web Page Whenever a web page becmes ut f date, yu can chse t update the web page address r delete the web page. 1. In the System Explrer, right-click a web page and select ne f the fllwing: Figure A. Saved web pages T edit the web page, select Edit. Refer t Adding a Web Page fr infrmatin abut the editable ptins. T delete the web page, select Delete. When the cnfirmatin dialg bx appears, click Yes. 112

121 Vide The Avigiln Cntrl Center Client sftware allws yu t mnitr live and recrded vide frm multiple cameras. While mnitring vide, yu have access t PTZ cntrls, digital zm, audi, manual recrding, digital utputs, and ther playback settings. T watch a vide f the applicatin's vide features, see the Intrductin t Avigiln Cntrl Center Client and Viewing Live Vide training vide and the Identifying, Bkmarking, Searching and Exprting Vide training vide in the Avigiln Training Center. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Mnitring Live Vide While mnitring live vide, yu can perfrm any f the fllwing prcedures. Adding and Remving Cameras in a View T mnitr vide, add a camera t the View. The camera vide can be remved frm the View any time. Adding a Camera t a View Perfrm ne f the fllwing: Drag the camera frm the System Explrer t an empty image panel in the View. Duble-click a camera in the System Explrer. In the System Explrer, right-click the camera and select Add t View. The camera is added t the next empty image panel in the View layut. Tip: Yu can drag the same camera t multiple image panels t watch the vide at different zm levels. 113

122 Avigiln Cntrl Center Enterprise Client User Guide Remving a Camera Frm a View Perfrm ne f the fllwing: Right-click the image panel and select Clse. Inside the image panel, click Clse. Displaying Live Vide Once a camera has been added t an image panel, yu can chse t watch the live vide stream. Yu can set the entire View t display live vide, r nly set specific image panels t display live vide. Live vide have a blue brder arund the image panel. T display live vide in a View, perfrm ne f the fllwing: Select View > Live. On the tlbar, select Live. T switch a single image panel t display live vide, right-click the image panel and select Live. Using Instant Replay T review an event that just ccurred, yu can immediately access recently recrded vide thrugh the instant replay feature. Right-click the image panel and select ne f the instant replay ptins: Replay - 30 Secnds Replay - 60 Secnds Replay - 90 Secnds The image panel immediately plays back the camera's mst recently recrded vide. Zming and Panning a Vide The zm and pan tls allw yu t fcus n specific regins in a camera vide. 114

123 Vide Using the Zm Tls The mst cmmn way t zm in and ut f the vide image is t rtate the scrll wheel n yur muse. The sftware als includes a set f Zm tls that can be used with yur muse: 1. Select a Zm tl: Frm the Tls menu, select Zm In Tl r Zm Out Tl. On the tlbar, click Zm In Tl r Zm Out Tl. 2. Click the image panel until yu reach the desired zm depth. Using the Pan Tls Yu can right-click and drag inside an image panel t pan the vide image. Or, yu can use the Pan tl: 1. Select the Pan tl: Frm the Tls menu, select Pan Tl. On the tlbar, click Pan Tl. 2. Drag the vide image in any directin inside the image panel. Mnitring PTZ Cameras PTZ cameras can be cntrlled thrugh the image panel nscreen cntrls r by using the tls in the PTZ Cntrls pane. Be aware that sme f tls and features may nt be displayed if they are nt supprted by yur camera. Cntrlling PTZ Cameras Pan, Tilt, Zm (PTZ) cntrls allw yu t cntrl cameras with PTZ features. Yu can cntrl a PTZ camera by using the nscreen cntrls r by using the tls in the PTZ Cntrls pane. See Keybard Cmmands fr ther ways t use the PTZ cntrls. 1. T display the PTZ Cntrls, perfrm ne f the fllwing: Frm the Tls menu, select PTZ Cntrls. On the tlbar, click PTZ Cntrls. 115

124 Avigiln Cntrl Center Enterprise Client User Guide The PTZ Cntrls are displayed belw the System Explrer. If the PTZ Cntrls are unavailable, select an image panel that is displaying vide frm a PTZ camera. Nte: The cntrls may appear different depending n the camera. Sme ptins are disabled r hidden if they are nt supprted by the camera. Figure A. PTZ Cntrls 2. T pan r tilt, perfrm ne f the fllwing: Click the rund Pan/Tilt arrw buttns in the PTZ Cntrls. The speed f the pan/tilt mvements can be adjusted using the Speed slider. In the image panel, drag yur muse frm center t mve the camera in that directin. The farther the cursr is frm the center f the image panel, the faster the camera will mve. If the camera supprts Click t Center, click anywhere n the image panel t center the camera t that pint. 116

125 Vide Figure B. PTZ Onscreen Cntrls 3. Use the ther PTZ cntrls t perfrm any f the fllwing: Actin Cntrl Prcedure T zm Click the and buttns. Click the image panel and use the muse scrll wheel t zm in and ut. If the camera supprts Drag t Zm, click and drag t create a green bx t define the area yu want t zm in and see. Right-click the image panel and select Zm Out Full. T cntrl the Iris r Fcus Click the and buttns. T prgram a PTZ preset 1. Mve the camera's field f view int psitin. 2. In the PTZ Cntrls pane, select a preset number and 117

126 Avigiln Cntrl Center Enterprise Client User Guide click. 3. In the Preset Name dialg bx, enter a name fr the preset and click OK. T activate a PTZ preset Select a preset and click. T return t the Hme preset psitin If the PTZ camera supprts a Hme preset psitin, the buttn is enabled. Click the buttn t return the camera t its Hme psitin. 1. In the PTZ Cntrls pane, select a pattern number and click. T prgram a PTZ pattern 2. Use the PTZ cntrls t mve the camera and create the pattern. 3. Click. T activate a PTZ pattern T activate a PTZ tur In the PTZ Cntrls pane, select a pattern number and click. The pattern will repeat until the pattern is stpped r anther pattern is run. In the PTZ Cntrls pane, select a tur number and click. The tur will repeat until stpped r until ther PTZ cntrls are used. T prgram a PTZ tur, see Prgramming PTZ Turs. T activate an auxiliary cmmand 1. Select an aux cmmand number and click. 2. Click t turn ff the auxiliary utput. T display the PTZ camera nscreen menu 1. Click the Menu buttn. 118

127 Vide 2. In the PTZ Cntrls pane, use the Pan/Tilt buttns t navigate the menu. Use the Pan/Tilt buttns t navigate the menu. Use the Zm buttns t mdify yur selectin chices. Use the Fcus buttns t cnfirm r cancel yur selectins. T lck the PTZ cntrls Click. N ther user will be able t use the PTZ cntrls fr this camera until yu unlck the cntrls r lg ut. Prgramming PTZ Turs If the PTZ camera supprts guard turs, the turs can be prgrammed thrugh the PTZ Cntrls pane. Turs allw the PTZ camera t autmatically mve between a series f preset psitins, and can be set t pause at each preset fr a specific amunt f time fr vide mnitring. 1. Create all the PTZ presets yu need fr this tur. See Cntrlling PTZ Cameras fr mre infrmatin. 2. In the PTZ Cntrls pane, select a tur number then click. The Edit PTZ Tur dialg bx is displayed. 119

128 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Edit PTZ Tur dialg bx 3. In the Edit PTZ Tur dialg bx, give the tur a name. 4. In the Tur Pause Duratin field, enter the amunt f time befre a tur repeats. Turs repeat until manually stpped, r until ther PTZ cntrls are used. 5. In the Tur Mde drp dwn list, select ne f the fllwing: Sequential: the PTZ camera will g t each preset in the set rder. Randm: the PTZ camera will g t each preset in randm rder. 6. Select the Set as default tur check bx if yu want this tur t run autmatically. The Default Tur Idle Start Time field is nw enabled, enter the amunt f time the PTZ camera must be idle fr befre this tur autmatically begins. 7. T add a preset, click and a preset is added t the list. 120

129 Vide 6. a. In the Preset clumn, select a preset frm the drp dwn list. b. In the Mve Speed clumn, enter hw fast yu want the PTZ camera t mve t this preset. The speed is 80% by default. c. In the View Time clumn, enter the amunt f time yu want the PTZ camera t stay at this preset psitin. The view time is 10 secnds by default. d. Repeat step 7 until all the presets fr this tur have been added. 7. T remve a preset, select the preset then click. 8. T re-rder a preset, select the preset then click r. The preset rder nly affects turs that use Sequential mde. 9. Click OK t save the tur. Listening t Audi in a View Nte: This feature is nly available if there is an Audi Channel License installed. If there is an audi input device linked t the camera, the Audi bar is displayed when yu mnitr the camera's vide. The Audi bar allws yu t listen t what is ccurring in the vide. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. T listen t the audi detected by the audi input device, perfrm any f the fllwing: In the lwer-right crner f the image panel, click t mute r activate the audi. Mve the slider t change the vlume. Figure A. Audi bar 121

130 Avigiln Cntrl Center Enterprise Client User Guide Bradcasting Audi in a View If there are speakers linked t the camera, the Micrphne icn is displayed when yu mnitr live vide. The Micrphne icn allws yu t bradcast yur verbal respnse t smething that is ccurring in the vide, like a Public Address (P.A.) system. Nte: This feature is nly available if there is a Speaker Channel License installed. T bradcast audi, hld and speak in t yur micrphne. The red bar mves t shw the micrphne's audi input levels. If the level is lw, speak luder r adjust the micrphne vlume in the Windws Cntrl Panel. Release the buttn t stp the bradcast. Triggering Manual Recrding Cameras are set t fllw a recrding schedule. If an event ccurs utside the camera's recrding schedule, yu can click the recrd indicatr icn t frce the camera t recrd the event. See Schedule fr mre infrmatin abut recrding schedules. The Recrd Indicatr verlay must be enabled fr manual recrding t wrk. See Displaying Vide Overlays fr mre infrmatin. The fllwing table explains the different camera recrding states. Blue = recrding Red = recrding triggered by an event Grey = nt recrding Starting and Stpping Manual Recrding In the tp-left crner f the image panel, click the Recrd Indicatr icn t start manual recrding. The recrd indicatr is highlighted in blue t shw that the camera is recrding. Manual recrding cntinues until it is stpped, r until the maximum manual recrding time is reached. Click the recrd indicatr again t stp manual recrding. 122

131 Vide The maximum manual recrding time is cnfigured in the Manual Recrding dialg bx, see Manual Recrding Settings fr mre infrmatin. Triggering Digital Output While yu mnitr live vide in an image panel, yu can manually trigger any digital utput that is cnnected t the camera. The digital utput is cnfigured in the Digital Inputs and Outputs dialg bx, see Setting Up Digital Outputs fr mre infrmatin. 1. Open the camera's live vide in an image panel. 2. In the image panel, click Trigger Digital Output. 3. If there is mre than ne digital utput linked t the camera, yu will be prmpted t select the digital utput yu want t trigger. Mnitring POS Transactins If a camera is linked t a pint f sales (POS) transactin surce, yu can mnitr live POS transactins while yu mnitr vide frm the linked camera. 1. Open the camera's vide in an image panel. 2. In the image panel, click View POS Transactins. Nte: If the camera is nt linked t a POS transactin surce, the icn is nt displayed. If there are mre than ne POS transactin surce linked t the camera, yu will be prmpted t select ne. The POS transactins are displayed in the next image panel. 123

132 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Live POS transactins displayed in an image panel Each transactin is separated by date and time, and the mst recent transactin is highlighted in blue. 3. T display cameras that are linked t the POS transactin surce, click View Camera in the POS transactin image panel. If multiple cameras are cnnected t the POS transactin surce, yu will be prmpted t select ne. Mnitring Recrded Vide While mnitring recrded vide, yu can perfrm any f the fllwing prcedures: Adding and Remving Cameras in a View T mnitr vide, add a camera t the View. The camera vide can be remved frm the View any time. Adding a Camera t a View Perfrm ne f the fllwing: Drag the camera frm the System Explrer t an empty image panel in the View. 124

133 Vide Duble-click a camera in the System Explrer. In the System Explrer, right-click the camera and select Add t View. The camera is added t the next empty image panel in the View layut. Tip: Yu can drag the same camera t multiple image panels t watch the vide at different zm levels. Remving a Camera Frm a View Perfrm ne f the fllwing: Right-click the image panel and select Clse. Inside the image panel, click Clse. Displaying Recrded Vide Once a camera has been added t an image panel, yu can chse t watch the camera's recrded vide. Yu can set the entire View t display recrded vide, r nly set specific image panels t display recrded vide. Recrded vide have a green brder arund the image panel. T display recrded vide in a View, perfrm ne f the fllwing: Select View > Recrded. On the tlbar, select Recrded. T switch a single image panel t display recrded vide, right-click the image panel and select Recrded. Zming and Panning a Vide The zm and pan tls allw yu t fcus n specific regins in a camera vide. Using the Zm Tls The mst cmmn way t zm in and ut f the vide image is t rtate the scrll wheel n yur muse. The sftware als includes a set f Zm tls that can be used with yur muse: 1. Select a Zm tl: 125

134 Avigiln Cntrl Center Enterprise Client User Guide Frm the Tls menu, select Zm In Tl r Zm Out Tl. On the tlbar, click Zm In Tl r Zm Out Tl. 2. Click the image panel until yu reach the desired zm depth. Using the Pan Tls Yu can right-click and drag inside an image panel t pan the vide image. Or, yu can use the Pan tl: 1. Select the Pan tl: Frm the Tls menu, select Pan Tl. On the tlbar, click Pan Tl. 2. Drag the vide image in any directin inside the image panel. Listening t Audi in a View Nte: This feature is nly available if there is an Audi Channel License installed. If there is an audi input device linked t the camera, the Audi bar is displayed when yu mnitr the camera's vide. The Audi bar allws yu t listen t what is ccurring in the vide. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. T listen t the audi detected by the audi input device, perfrm any f the fllwing: In the lwer-right crner f the image panel, click t mute r activate the audi. Mve the slider t change the vlume. Figure A. Audi bar 126

135 Vide Playing Back Recrded Vide The Timeline displays when vide was recrded and lets yu play back the recrdings. The clred bars n the Timeline shw the camera's recrding histry: A red bar shws the camera recrded an event. A blue bar shws the camera recrded vide. White areas shw that the camera did nt recrd any vide. An range bar is a bkmark in the camera's recrding histry. See Bkmarking Recrded Vide fr mre infrmatin abut bkmarks. Figure A. Playback tls n the Timeline Use any f the fllwing cntrls t playback the recrded vide files: Actin Cntrl Prcedure T select a playback time T add a bkmark Click the calendar icn and select a date and time. Or, click n a pint in the Timeline. Click Add Bkmark t add a bkmark n the Timeline. T start playback Click Play. T stp playback Click Pause. 127

136 Avigiln Cntrl Center Enterprise Client User Guide T mve frward a frame Click Step Frward. T mve back a frame Click Step Backward. T cntrl the playback directin and speed Drag the slider t the right t mve the vide frward. Drag the slider t the left t mve the vide backward. The farther away the slider is frm center the faster the playback speed. T jump frward r back n the Timeline On the Timeline, click ne f the G Frward r G Back buttns t mve t different pints n the Timeline. T expand the Timeline t a specific mment in time Mve the slider n the bttm right t zm in r ut n the Timeline. Or, yu can place yur muse ver the Timeline and use the scrll wheel t zm in r ut n the Timeline. T center the Timeline n the time marker Right-click the Timeline, and select Center n Marker. T mve thrugh the Timeline quickly with the time marker T pan the Timeline Drag the time marker thrugh the Timeline. Mve the hrizntal scrll bar under the Timeline. Or, right-click and drag the Timeline. Bkmarking Recrded Vide Yu can add bkmarks t recrded vide t help yu find and review an event later. Bkmarked vide can be prtected against scheduled data cleanup s the vide is never deleted. 128

137 Vide Adding a Bkmark 1. T pen the Edit Bkmark dialg bx, perfrm ne f the fllwing: On the Timeline, click Add Bkmark. Drag the time marker t where yu want t start the bkmark, then right-click and select Add Bkmark. The Edit Bkmark dialg bx appears, and the bkmark time range is highlighted n the Timeline Figure A. Add Bkmark dialg bx 2. Enter a name fr the bkmark. 3. In the Cameras pane, select all the cameras that are attached t this bkmark. Nte: Yu can nly bkmark multiple cameras frm the same server. 4. In the Time Range t Bkmark area, enter the time yu want t bkmark. Yu can als mve the black time range markers n the Timeline t adjust the time range. 129

138 Avigiln Cntrl Center Enterprise Client User Guide 5. In the Descriptin field, enter any infrmatin abut the bkmark. 6. T prtect the bkmark vide frm being deleted, select the Prtect bkmark data check bx. Nte: Prtected bkmarks are never deleted. Be aware that bkmarked vide take up space and becme the ldest vide n the server. 7. Click OK. Editing, Deleting r Exprting a bkmark 1. Click the bkmark n the Timeline then perfrm ne f the fllwing: Figure B. Bkmark prperties T Edit a bkmark Delete a bkmark Exprt a bkmark D this... Click Edit then make yur changes. Click Delete. When the cnfirmatin dialg bx appears, click Yes. Click Exprt then cmplete the Exprt tab. When editing a bkmark, refer t Adding a Bkmark fr details abut the editable ptins. When exprting a bkmark, refer t Exprting Recrded Vide and Images fr infrmatin abut the exprt ptins. 130

139 Vide Reviewing POS Transactins While yu mnitr recrded vide, yu can als review the POS transactins that ccur in the vide. 1. Add a camera that is linked t the POS transactin surce t the View, and display the camera's recrded vide 2. In the image panel, click View POS Transactins. If there are mre than ne POS transactin surce linked t the camera, yu will be prmpted t select ne. The POS transactins are displayed in the next image panel. Figure A. Recrded POS transactins displayed in an image panel Each transactin is separated by date and time. When yu select a transactin, the vide mves t that event n the Timeline. Scrll up r dwn t see ther transactins frm the POS transactin surce. 3. T display cameras that are linked t the POS transactin surce, click View Camera in the POS transactin image panel. If multiple cameras are cnnected t the POS transactin surce, yu will be prmpted t select ne. 4. Use the Timeline t review the vide in mre detail. 131

140 Avigiln Cntrl Center Enterprise Client User Guide Fr mre infrmatin abut Timelines, see Playing Back Recrded Vide. If yu want t find a specific POS transactin, see Perfrming a POS Transactin Search. Adjusting Vide Display in Image Panels Yu can adjust the image panel display settings t imprve the vide display n yur mnitr. Maximizing an Image Panel Yu can maximize an image panel t enlarge the vide display. Maximizing an Image Panel Perfrm ne f the fllwing: Right-click an image panel and select Maximize. Inside the image panel, click Maximize. Duble-click the image panel. Restring an Image Panel Perfrm ne f the fllwing: Right-click the maximized image panel and select Restre Dwn. Inside the image panel, click Restre Dwn. Duble-click the image panel. Displaying Vide Overlays When yu mnitr vide in a View, yu can select the type f infrmatin that is displayed ver the vide. Select View > Image Overlays, then select ne r mre f the fllwing: Optin Camera Name Descriptin Displays the name given t the camera. 132

141 Vide Camera Lcatin Timestamp Recrd Indicatr Displays the lcatin given t the camera. (Recrded vide nly) Displays the expsure timestamp fr the vide. (Live vide nly) Displays the recrding status f a camera. The recrding status is indicated by the rund Recrd Indicatr icn n the tp left crner f the image panel. The clr f the icn shws the camera's recrding status. Red: recrding triggered by an event Blue: recrding Grey: nt recrding Select the Recrd Indicatr icn at any time t begin manual recrding. Mtin Activity License Plate Highlights detected mtin events in red. (Live vide nly) Displays license plate numbers as they are detected. Nte: This feature is nly available if the License Plate Recgnitin feature is installed. Changing the Image Panel Display Quality Settings If yu d nt have enugh netwrk bandwidth r prcessing pwer, yu may nt be able t watch vide at the full image rate and full quality. Yu can bias the image panels t display vide in high quality and lw frame rate, r lw quality and high frame rate. The Change Display Quality settings nly affect the image panel display and des nt affect the actual vide quality r image rate between the camera and the server. T change the camera's actual display settings, see Cmpressin and Image Rate. 1. Open the Change Display Quality dialg bx: Select Tls > Change Display Quality... In the tlbar, click Change Display Quality. 2. In the Change Display Quality dialg bx, select ne f the fllwing: 133

142 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Change Display Quality dialg bx Maximum: displays the full vide reslutin with the lwest image rate. High: displays 1/4 f the full vide reslutin. Medium: displays 1/16 f the full vide reslutin. Lw: displays 1/64 f the full vide reslutin with the highest image rate. 3. Select the Mnchrme check bx t display the vide in black and white. 4. Click OK. Changing the Image Panel Display Adjustments Settings Yu can change the image panel display settings t bring ut vide details that are hard t see with the image panel's default settings. 1. Right-click an image panel and select Display Adjustments

143 Vide Figure A. Display Adjustments dialg bx 2. Mve the sliders t adjust the Gamma, Black Level and White Level. The image panel displays a preview f yur changes. 3. Click Restre Defaults t clear yur changes. 4. Click Clse t save yur changes. Displaying Analg Vide in Deinterlaced Mde If there are visible interlacing artifacts in the analg camera vide, yu can enable the deinterlacing filter t help imprve the vide image. Select View > Display Deinterlaced Images. 135

144 Alarms The Alarms tab allws yu t mnitr and acknwledge alarms. Alarms are created in the server Setup, see Alarms fr mre infrmatin. T watch a vide verview f the alarm mnitring feature, see the Alarm Mnitring training vide in the Avigiln Training Center. Accessing the Alarms Tab Perfrm ne f the fllwing steps t pen the Alarms tab: Frm the Tls menu, select Alarms... On the tlbar, click Alarms. 136

145 Alarms Figure A. Alarms tab The Alarms tab is divided int the fllwing areas: In the Alarms list is a list f alarms that are active, acknwledged, r assigned t anther user. The alarms are srted by status, pririty then time. In the Assigned Alarms list are the alarms that are assigned t yu. If there are n alarms assigned t yu, the Assigned Alarms list is nt displayed. The Alarm Details area displays the triggers and vide linked t an alarm. The Timeline is used t play back the recrded alarm vide. 137

146 Avigiln Cntrl Center Enterprise Client User Guide Reviewing Alarms In the Alarms tab, yu can review alarm vide and manage alarms. Active alarms can be assigned t yurself, and acknwledged alarms can be exprted r purged as required. Reviewing Alarm Vide Yu can review active and acknwledged alarm vide in detail thrugh the alarm image panel, r pening the alarm vide in a new View. 1. Select an alarm frm the Alarms list. The alarm details are displayed. 2. In the Alarm Triggers list, select an alarm trigger t display the vide fr that instance f the alarm. 3. Use the alarm image panel cntrls t review the vide in mre detail. Figure A. Alarm image panel In the Camera drp dwn list, select a camera that is linked t the alarm t review the vide. Use the Zm and Pan tls t review the vide image in mre detail. Use the Live and Recrded buttns t alternate frm the recrded alarm vide and the camera's live stream. 4. Click Open In View t pen the alarm vide in a new View. 5. Use the Timeline t cntrl the vide play back. 138

147 Alarms See Playing Back Recrded Vide fr infrmatin abut the Timeline cntrls. Bkmarking an Alarm Yu can bkmark active and acknwledged alarm vide. 1. Select an alarm frm the Alarms list then click Bkmark Alarm. 2. When the Edit Alarms dialg bx appears, define the details f yur bkmark. The Edit Bkmark dialg bx autmatically selects all the cameras that are linked t the alarm, and sets the time range t span the first and last alarm trigger. After yu make the required changes, click OK. See Bkmarking Recrded Vide fr mre infrmatin abut the bkmark ptins. Assigning an Alarm Yu can assign an alarm t yurself t let thers knw that the alarm is being reviewed. Althugh yu can nly assign alarms t yurself, yu can unassign the alarm at any time. 1. Select an active alarm frm the Alarms list. 2. When the alarm details are displayed, click Assign Alarm. The alarm is added t yur Assigned Alarms list. 3. T unassign an alarm, select the alarm frm the Assigned Alarms list and click Unassign Alarm. Acknwledging an Alarm Acknwledging an alarm shws that an alarm has been reviewed and is n lnger active. Yu can acknwledge any alarm that is active r assigned t yu. 1. After reviewing the alarm, enter ntes describing the nature f the alarm in the Acknwledge Alarm text bx. 2. Click Acknwledge. 3. If there is a digital utput linked t the alarm, a dialg bx may appear t ask fr permissin t activate the digital utput. Activate the digital utput as required. The Alarm is given an Acknwledged status in the Alarms list. 139

148 Avigiln Cntrl Center Enterprise Client User Guide Searching Alarms Yu can search thrugh an alarm's histry t review ther instances f the alarm. 1. Select an acknwledged alarm frm the Alarms list. 2. In the alarm details area, click Search Alarm. See Perfrming an Alarm Search fr infrmatin abut the alarm search ptins. Exprting Alarms Yu can exprt alarm vide fr review n ther cmputers. 1. Select an acknwledged alarm frm the Alarms list. 2. In the alarm details area, click Exprt Alarm. See Exprting Recrded Vide and Images fr infrmatin abut the exprt ptins. Purging an Alarm Purging an alarm remves the alarm frm the Alarms list until the alarm is activated again. Althugh purged alarms are n lnger listed in the Alarms list, yu can still search thrugh the alarm's histry. 1. Select an acknwledged alarm frm the Alarms list. 2. In the alarm details area, click Purge Alarm. Arming Image Panels Arming an image panel reserves the image panel specifically fr displaying vide linked t alarms r rules. Armed image panels allw yu t review and acknwledge alarms while mnitring vide in a View. Any image panel can be armed r disarmed as required. If there are n armed image panels, alarm vide will appear in the next empty image panel in the current View, r in a new View if all current image panels are in use. 140

149 Alarms Figure A. Armed image panel Yu can perfrm any f the fllwing t add and use an armed image panel: Tip: Yu can still use the features that are cmmn t all image panels, like snapsht r maximizing an image panel. T... Arm an image panel D this... Click the Arm Panel buttn. The image panel is given a red brder and an alarm label t shw that it is armed. Acknwledge an alarm Click the Acknwledge buttn. Mve between linked alarm vide If the alarm is linked t multiple cameras, use the green arrws t mve between the linked cameras. Disarm an image panel Click the Disarm Panel buttn. If multiple alarms are triggered at the same time, the linked vide are queued inside the armed image panel. The alarm vide are displayed by rder f alarm pririty then time. Once an alarm is acknwledged r assigned t a user, the alarm vide is remved frm the armed image panel. Nte: If yu chse t clse a vide in the armed image panel, the vide is remved but the alarm cntinues t be active. 141

150 Avigiln Cntrl Center Enterprise Client User Guide Vide triggered by a rule are queued in the armed image panel after alarms, with the mst recent vide displayed first. Rules vide are nt labeled and d nt need t be acknwledged. 142

151 License Plates License Plate Recgnitin (LPR) is a licensed feature that allws yu t mnitr vehicle license plates that are detected by the Avigiln Cntrl Center. Yu can use the license plate verlay t mnitr license plates as they are detected. Or, yu can use the License Plate Watch List feature t alert yu when specific license plates are detected. T setup License Plate Recgnitin, see License Plate Recgnitin fr mre infrmatin. License Plate Overlay While yu mnitr vide in an image panel, yu can als mnitr license plates as they are detected by the Avigiln Cntrl Center. When the license plate verlay is enabled, detected license plate numbers are displayed in the bttm right crner f the image panel. T enable the License Plate verlay: 1. Select View > Image Overlays > License Plate. 2. Add a camera cnfigured fr license plate recgnitin t the View. License Plate Recgnitin Watch List The License Plate Recgnitin (LPR) Watch List tracks the license plates yu've cnfigured the Avigiln Cntrl Center t recgnize, and alerts yu when matches are detected in the License Plate Matches dialg bx. T cnfigure the Watch List, see Cnfiguring the Watch List fr mre infrmatin. Reviewing the License Plate Matches 1. Open the License Plate Matches dialg bx. 143

152 Avigiln Cntrl Center Enterprise Client User Guide The License Plate Matches dialg bx autmatically appears when license plates frm the Watch List are detected. T review matches at a separate time, select LPR > License Plate Matches... Figure A. License Plate Matches dialg bx. 2. Select ne f the license plate matches and perfrm any f the fllwing: Click View this Event r duble-click the selected license plate t pen a snapsht f the detected license plate in a new View. Click Delete t delete the license plate frm the list. Click Clear All t empty the current match list. The list is reppulated as new license plates are detected. 3. Click Clse. 144

153 Search Yu can search fr recrded vide that are linked t an event, r simply search thrugh the camera's recrding histry. T watch a vide verview f the Search features, see the Identifying, Bkmarking, Searching and Exprting Vide training vide in the Avigiln Training Center. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Figure A. Search ptins 145

154 Avigiln Cntrl Center Enterprise Client User Guide Perfrming an Event Search The Event Search allws yu t search fr a specific mtin events and digital input events. 1. Click Search t pen the Search tab. 2. In the Search tab, select Event Search. The Search:Event tab is displayed. Figure A. Search: Event tab 3. In the Camera t Search area, select all the cameras yu want t include in the search. 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. In the Events t Search Fr area, select the types f events t include in the search. 6. Click Start Search. 146

155 Search Viewing Event Search Results 1. In the Search Results area, select a search result. The event is highlighted n the Timeline and the vide is displayed in the search image panel. Details abut the search result are displayed n the right. Tip: Yu can change the size f the image panel by mving the edge f the search results. 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. Click Exprt this event t exprt the selected event vide. See Exprting Recrded Vide and Images fr mre infrmatin. 4. If yu want t further refine yur search, click Perfrm a pixel search n this event. Yu can nw search fr any pixel mvement in the selected result. See Perfrming a Pixel Search fr mre infrmatin. 5. Click Bkmark this event t bkmark the selected search result. See Bkmarking Recrded Vide fr mre infrmatin. 6. T exprt all listed results, click Exprt results t a file and save the file. Perfrming a Bkmark Search The Bkmark Search allws yu t search fr a specific bkmark. 1. Click Search t pen the Search tab. 2. In the Search tab, select Bkmark Search. The Search:Bkmark tab is displayed. All available bkmarks are listed n the left. 147

156 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Search:Bkmark tab 3. In the Search field, enter any text that may appear in the bkmark's title, descriptin, linked camera name r the name f the user wh created the bkmark. The search is autmatically perfrmed n all the listed bkmarks until nly the matches are displayed. Viewing Bkmark Search Results 1. In the Bkmark list, select a bkmark. The bkmark is highlighted n the Timeline and the vide is displayed in the image panel. Details abut the bkmark are displayed under the image panel. 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. Click Exprt this bkmark t exprt the selected bkmark. See Exprting Recrded Vide and Images fr mre infrmatin. 4. If yu want t further refine yur search, click Perfrm a pixel search n this bkmark. Yu can nw search fr any pixel mvement in the selected bkmarked vide. 148

157 Search See Perfrming a Pixel Search fr mre infrmatin. 5. Click Edit this bkmark t edit the bkmark. See Bkmarking Recrded Vide fr mre infrmatin. Perfrming a Pixel Search The Pixel Search allws yu t search fr tiny pixel change in specific areas in the camera s field f view. 1. Click Search t pen the Search tab. 2. In the Search tab, select Pixel Search. The Search:Pixel tab displays. Figure A. Search:Pixel tab By default, the entire search image panel is highlighted in green. 3. In the Camera t Search area, select a camera. 149

158 Avigiln Cntrl Center Enterprise Client User Guide 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Define the pixel search area by using the mtin detectin tls abve the image panel. Only areas highlighted in green are searched. 6. In the Pixel Search Optins area, drag the Threshld slider t select the amunt f mtin required t return a search result. A high threshld requires mre pixels t change befre results are fund. 7. Enter a number in the Jin results less than field t set the minimum number f secnds between separate search results. Yu can enter any number between secnds. 8. Click Start Search. Viewing Pixel Search Results 1. In the Search Results area, select a search result. The event is highlighted n the Timeline and the vide is displayed in the search image panel. Details abut the search result are displayed n the right. Tip: Yu can change the size f the image panel by mving the edge f the search results. 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. Click Exprt this event t exprt the selected event vide. See Exprting Recrded Vide and Images fr mre infrmatin. 4. T exprt all listed results, click Exprt results t a file and save the file. Perfrming a Thumbnail Search The Thumbnail Search is a visual search that displays the search results as a series f thumbnail images. 1. Click Search t pen the Search tab. 2. In the Search tab, select Thumbnail Search. The Search:Thumbnails tab displays. 150

159 Search Figure A. Search:Thumbnails tab 3. In the Camera t Search area, select a camera. 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. In the image panel, mve r drag the edges f the green verlay t fcus the search n ne area in the vide image. Only the area highlighted in green is searched. 6. Click Start Search. Viewing Thumbnail Search Results The search results display thumbnails at equal intervals n the Timeline. 1. T change the size f the search result thumbnails, select Large Thumbnails, Medium Thumbnails, r Small Thumbnails frm the drp-dwn menu abve the search results and click Search Again. 151

160 Avigiln Cntrl Center Enterprise Client User Guide Figure B. Search:Thumbnail results tab 2. Select a thumbnail t highlight the vide n the Timeline. 3. Click Step In, r duble-click the thumbnail t perfrm anther search arund the thumbnail. Click Back t return t the previus results page. 4. Click Open In View t pen the recrded vide in a new View. 5. Click Change Search t change the search criteria. Perfrming an Alarm Search Alarm search allws yu t search thrugh an alarm's histry. 1. Click Search t pen the Search tab. 152

161 Search 2. In the Search tab, select Alarm Search. The Search:Alarms tab is displayed. Figure A. Search:Alarms tab 3. In the Alarm t Search list, select all the alarms yu wuld like t include in the alarm search. 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Click Start Search. Viewing Alarm Search Results 1. In the Search Results area, select a search result. The event is highlighted n the Timeline and the vide is displayed in the search image panel. Details abut the search result are displayed n the right. 153

162 Avigiln Cntrl Center Enterprise Client User Guide Tip: Yu can change the size f the image panel by mving the edge f the search results. 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. If the event is linked t multiple cameras, select a camera frm the Camera drp dwn list t change the vide displayed in the image panel. 4. Click Exprt this event t exprt the selected event vide. See Exprting Recrded Vide and Images fr mre infrmatin. 5. Click Bkmark this event t bkmark the selected search result. See Bkmarking Recrded Vide fr mre infrmatin. 6. T exprt all listed results, click Exprt results t a file and save the file. Perfrming a POS Transactin Search The POS Transactin Search allws yu t search fr specific transactins. 1. Click Search t pen the Search tab. 2. In the Search tab, select POS Transactins Search. The Search: POS Transactins tab is displayed. 154

163 Search Figure A. Search:POS Transactins tab 3. In the POS Transactin Surces t Search area, select all the POS transactin surces yu wuld like t include in the search. 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. In the Search Text area, enter any text that will help yu filter the search results. Fr example, yu can enter prduct names r transactin values. Use the Wildcards and Regular Expressin search methds t find a range f results. Leave the Text field blank t find all transactins. 6. Click Start Search. Viewing POS Transactin Search Results 1. In the Search Results area, select a search result. The event is highlighted n the Timeline and the vide is displayed in the search image panel. Details abut the search result are displayed n the right. 155

164 Avigiln Cntrl Center Enterprise Client User Guide Tip: Yu can change the size f the image panel by mving the edge f the search results. 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. If the event is linked t multiple cameras, select a camera frm the Camera drp dwn list t change the vide displayed in the image panel. 4. Click Exprt this event t exprt the selected event vide. See Exprting Recrded Vide and Images fr mre infrmatin. 5. Click Bkmark this event t bkmark the selected search result. See Bkmarking Recrded Vide fr mre infrmatin. 6. T exprt all listed results, click Exprt results t a file and save the file. Perfrming a License Plate Search The License Plate Search allws yu t search fr detected license plates, including license plates nt listed in the Watch List. Nte: The License Plate Search is nly available if the License Plate Recgnitin feature is installed. 1. Click Search t pen the Search tab. 2. In the Search tab, select License Plate Search. The Search: License Plates tab is displayed. 156

165 Search Figure A. Search: License Plates tab 3. In the Camera t Search area, select all the cameras yu want t include in the search. 4. In the Time Range t Search area, set the date and time range f yur search. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t mdify the time range. 5. In the License Plate Search Optins area, enter the license plate yu want t find and a minimum cnfidence f a match. 6. Click Start Search. Viewing License Plate Search Results 1. In the Search Results area, select a search result. The event is highlighted n the Timeline and the vide is displayed in the search image panel. Details abut the search result are displayed n the right. Tip: Yu can change the size f the image panel by mving the edge f the search results. 157

166 Avigiln Cntrl Center Enterprise Client User Guide 2. Use the Timeline cntrls t review the event. See Playing Back Recrded Vide fr mre infrmatin. 3. If the event is linked t multiple cameras, select a camera frm the Camera drp dwn list t change the vide displayed in the image panel. 4. Click Exprt this event t exprt the selected event vide. See Exprting Recrded Vide and Images fr mre infrmatin. 5. Click Bkmark this event t bkmark the selected search result. See Bkmarking Recrded Vide fr mre infrmatin. 6. T exprt all listed results, click Exprt results t a file and save the file. 158

167 Exprt Yu can exprt vide in multiple vide and image frmats. Yu can als exprt snapshts f an image panel as yu mnitr vide. T watch a vide verview f the Exprt features, see the Identifying, Bkmarking, Searching and Exprting Vide training vide in the Avigiln Training Center. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Exprting a Snapsht f an Image Yu can exprt a snapsht f any image panel with vide. When yu exprt a snapsht, yu are exprting whatever the image panel is currently displaying. 1. T exprt a snapsht, perfrm ne f the fllwing: In the image panel, click the Save Snapsht icn. Right-click the image panel and select Save Snapsht. The snapsht Exprt tab is displayed, and the image yu want t exprt is displayed. 159

168 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Exprt tab fr Snapsht exprt 2. In the Frmat drp dwn list, select an exprt frmat. 3. Fr the selected exprt frmat, define yur preferences: Frmat Native Nte: The Native frmat requires the Avigiln Cntrl Center Player t view. Image ptins This is the recmmended exprt frmat because the exprted image maintains its riginal cmpressin and can be authenticated against tampering in the Avigiln Cntrl Center Player. Select the Exprt the Cntrl Center Player Installer check bx if yu want a cpy f the Avigiln Cntrl Center Player t be distributed with yur native image file. 1. In the Reslutin field, select a reslutin fr the vide image. Yu can manually enter the reslutin r click the drp dwn arrw t select a standard reslutin. PNG Nte: The Reslutin field autmatically maintains the image aspect rati. 2. Click Change Image Regin... t nly exprt part f the vide image. In the Change Image Regin dialg bx, mve and resize the green 160

169 Exprt verlay then click OK. Only areas highlighted in green are exprted. 3. Select the image verlays yu want: Timestamp, Camera name, and Camera lcatin. 4. Click Display Adjustments t adjust the Gamma, Black Level and/r White Level. 1. In the Quality field, select an image quality level. 2. Set the image Reslutin. JPEG 3. Click Change Image Regin t nly exprt a part f the vide image. 4. Select the image verlays yu want. 5. Click Display Adjustments t mdify the image quality. 1. Set the image Reslutin. TIFF 2. Click Change Image Regin t nly exprt a part f the vide image. 3. Select the image verlays yu want. 4. Click Display Adjustments t mdify the image quality. 1. Click Change Image Regin t nly exprt a part f the vide image. 2. Click Printer Settings... t change the selected printer and paper size. Print 3. Select the image verlays yu want. 4. Click Add Exprt Ntes... t add ntes abut the exprted image. The ntes are printed belw the image. 5. Click Display Adjustments t mdify the image quality. 1. Click Change Image Regin t nly exprt a part f the vide image. PDF 2. Select the image verlays yu want. 3. Click Add Exprt Ntes... t add ntes abut the exprted image. 4. Click Display Adjustments t mdify the image quality. 4. Click Start Exprt. 5. In the Save As dialg bx, name the exprt file and click Save. 161

170 Avigiln Cntrl Center Enterprise Client User Guide The Preview area displays the snapsht yu are exprting. 6. When the exprt is cmplete, click OK. Exprting Live Images The Live Exprt tab exprts live vide as a series f still images. Yu can chse the file frmat, and select yur exprt preferences. 1. Select File > Live Exprt... The Live Exprt tab is displayed. Figure A. Live Exprt tab 2. In the Camera t Exprt list, select the camera vide yu want t exprt. 3. In the Frmats drp dwn list, select an exprt frmat: PNG, JPEG, r TIFF. 4. Set the exprt image rate: Optin Exprt at full image rate Descriptin Select this ptin t exprt the live stream at 162

171 Exprt the full image rate. Exprt ne image every min sec Only keep the mst recent image(s) Select this ptin t cntrl the time between each exprted image. Fr example, if yu enter 5 min. 0 sec., nly ne image will be exprted every 5 minutes. Select this check bx t limit the number f images stred. Be aware that if yu d nt limit the number f images stred, the exprt will cntinue until yur hard drive is full. 5. (JPEG images nly) In the Quality drp dwn list, select the exprted image quality level. 6. In the Reslutin field, select a reslutin fr the vide image. Yu can manually enter the reslutin r click the drp dwn arrw t select a standard reslutin. Nte: The Reslutin field autmatically maintains the image aspect rati. 7. Click Change Image Regin... t nly exprt part f the vide image. In the Change Image Regin dialg bx, mve and resize the green verlay then click OK. Only areas highlighted in green are exprted. 8. Select the image verlays yu want: Timestamp, Camera name, and Camera lcatin. 9. Click Display Adjustments t adjust the gamma, black level and/r white level. 10. Click Start Exprt. 11. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide yu are exprting. Nte: The live exprt will cntinue until stpped. 12. Click Stp Exprt t stp the exprt. Exprting Recrded Vide and Images Use the Exprt tab t exprt recrded vide in different vide and image frmats. Nte: Only recrded vide can be exprted in vide frmat. 163

172 Avigiln Cntrl Center Enterprise Client User Guide Accessing the Exprt Tab The Exprt tab can be accessed in any f the fllwing ways: On the tlbar, click Exprt. Select File > Exprt. While perfrming a search, select a search result and click Exprt this event. While reviewing bkmarked vide, right-click a bkmark n the Timeline and select Exprt. Exprting Native Vide The Native (AVE) frmat is the recmmended frmat fr exprting vide. Yu can exprt vide frm multiple cameras in a single file, and the vide maintains its riginal cmpressin. AVE vide is played in the Avigiln Cntrl Center Player, where the vide can be authenticated against tampering and be reexprted t ther frmats. 1. Click Exprt t pen the Exprt tab. 164

173 Exprt Figure A. Exprt tab fr recrded vide exprt 2. In the Frmat drp dwn list, select Native. 3. In the Camera t Exprt list, select the camera vide yu want t exprt. 4. Enter the time range yu want t exprt. The time range is highlighted n the Timeline by black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Set the exprt image rate: Optin Exprt at image rate Descriptin Select this ptin t cntrl hw many images per secnd are exprted. Fr example, the vide is streaming at 30 images per secnd. If yu select 1/2, nly 15 images fr that secnd will be exprted. 165

174 Avigiln Cntrl Center Enterprise Client User Guide Exprt ne image every min sec Select this ptin t cntrl the time between each exprted vide image. Fr example, if yu enter 5 min. 0 sec., nly ne image will be exprted every 5 minutes. 6. T include a cpy f the Avigiln Cntrl Center Player with yur exprt, select the Exprt the Cntrl Center Player Installer check bx. 7. T autmatically divide the exprt int separate files that can be stred n ptical media (like a CD r DVD), select the Split file int sizes f: check bx. Then, manually enter a maximum file size in MB r select a pre-cnfigured ptin frm the drp dwn list. 8. Click Start Exprt. 9. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide yu are exprting. 10. When the exprt is cmplete, click OK. Exprting AVI Vide Vide exprted in Audi Vide Interleave (AVI) frmat can be played in mst media players. 1. Click Exprt t pen the Exprt tab. 166

175 Exprt Figure A. Exprt tab fr recrded vide exprt 2. In the Frmat drp dwn list, select AVI vide. 3. In the Camera t Exprt list, select the camera vide yu want t exprt. 4. Enter the time range yu want t exprt. The time range is highlighted n the Timeline by black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Set the exprt image rate: Optin Exprt at image rate Descriptin Select this ptin t cntrl hw many images per secnd are exprted. Fr example, the vide is streaming at 30 images per secnd. If yu select 1/2, nly 15 images fr that secnd will be exprted. 167

176 Avigiln Cntrl Center Enterprise Client User Guide Exprt ne image every min sec Select this ptin t cntrl the time between each exprted vide image. Fr example, if yu enter 5 min. 0 sec., nly ne image will be exprted every 5 minutes. 6. In the Encder field, select the cmpressin used. The VC-1 (Windws Media Vide) cmpressin is included by default because it is tailred fr high-reslutin AVI encding. 7. In the Quality drp dwn list, select the exprted image quality level. 8. In the Reslutin field, select a reslutin fr the vide image. Yu can manually enter the reslutin r click the drp dwn arrw t select a standard reslutin. Nte: The Reslutin field autmatically maintains the image aspect rati. Fr high reslutin vide (11MP r 16MP) the greatest reslutin ptin will be less than the camera's actual reslutin because mst media players cannt play high reslutin AVI files. 9. T autmatically divide the exprt int separate files that can be stred n ptical media (like a CD r DVD), select the Split file int sizes f: check bx. Then, manually enter a maximum file size in MB r select a pre-cnfigured ptin frm the drp dwn list. 10. Click Change Image Regin... t nly exprt part f the vide image. In the Change Image Regin dialg bx, mve and resize the green verlay then click OK. Only areas highlighted in green are exprted. 11. Select the Skips recrding gaps check bx t avid pauses in the vide caused by gaps in the recrding. 12. Select the image verlays yu want: Timestamp, Camera name, and Camera lcatin. 13. Click Display Adjustments t adjust the gamma, black level and/r white level. 14. Click Start Exprt. 15. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide yu are exprting. 16. When the exprt is cmplete, click OK. Exprting PNG, JPEG r TIFF Images Vide can be exprted as a series f still images in PNG, JPEG, r TIFF frmat. 1. Click Exprt t pen the Exprt tab. 168

177 Exprt Figure A. Exprt tab fr still image exprt 2. In the Frmat drp dwn list, select PNG Images, JPEG Images, r TIFF Images. 3. In the Camera t Exprt list, select the camera vide yu want t exprt. 4. Enter the time range yu want t exprt. The time range is highlighted n the Timeline by black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Set the exprt image rate: Optin Exprt at image rate Descriptin Select this ptin t cntrl hw many images per secnd are exprted. Fr example, the vide is streaming at 30 images per secnd. If yu select 1/2, nly 15 images fr that secnd will be exprted. 169

178 Avigiln Cntrl Center Enterprise Client User Guide Exprt ne image every min sec Select this ptin t cntrl the time between each exprted vide image. Fr example, if yu enter 5 min. 0 sec., nly ne image will be exprted every 5 minutes. 6. Select the Exprt at mst images check bx and enter a number t limit the amunt f images that are exprted. 7. (JPEG nly) In the Quality drp dwn list, select the exprted image quality level. 8. In the Reslutin field, select a reslutin fr the vide image. Yu can manually enter the reslutin r click the drp dwn arrw t select a standard reslutin. Nte: The Reslutin field autmatically maintains the image aspect rati. 9. Click Change Image Regin... t nly exprt part f the vide image. In the Change Image Regin dialg bx, mve and resize the green verlay then click OK. Only areas highlighted in green are exprted. 10. Select the image verlays yu want: Timestamp, Camera name, and Camera lcatin. 11. Click Display Adjustments t adjust the gamma, black level and/r white level. 12. Click Start Exprt. 13. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide yu are exprting. 14. When the exprt is cmplete, click OK. Exprting PDF and Print Images Vide can be exprted as still images fr printing r in PDF frmat. 1. Click Exprt t pen the Exprt tab. 170

179 Exprt Figure A. Exprt tab fr still image exprt 2. In the Frmat drp dwn list, select Print Image r PDF File. 3. In the Camera t Exprt list, select the camera vide yu want t exprt. 4. In the Time field, enter the exact date and time f the vide image yu want t exprt. 5. Click Change Image Regin... t nly exprt part f the vide image. In the Change Image Regin dialg bx, mve and resize the green verlay then click OK. Only areas highlighted in green are exprted. 6. (Print Image nly) Click Print Settings t change the printer and paper size that the image is printed n. 7. Select the image verlays yu want: Timestamp, Camera name, and Camera lcatin. 171

180 Avigiln Cntrl Center Enterprise Client User Guide 8. Click Add Exprt Ntes t add ntes abut the exprted image. The ntes are added belw the image. 9. Click Display Adjustments t adjust the gamma, black level and/r white level. 10. Click Start Exprt. 11. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide yu are exprting. 12. When the exprt is cmplete, click OK. Exprting WAV Audi If a vide cntains audi, the audi is exprted with the vide. If required, yu can chse t nly exprt the audi file. Nte: Audi recrding requires an Audi Channel License. Withut an audi license, n audi wuld have been recrded with the vide. 1. Click Exprt t pen the Exprt tab. 172

181 Exprt Figure A. Exprt tab fr audi exprt 2. In the Frmat drp dwn list, select WAV. 3. In the Camera t Exprt list, select the camera vide yu want t exprt. 4. Enter the time range yu want t exprt. The time range is highlighted n the Timeline by black time range markers. Yu can als drag the time range markers t mdify the time range. 5. Click Start Exprt. 6. In the Save As dialg bx, name the exprt file and click Save. The Preview area displays the vide linked with the audi yu are exprting. 7. When the exprt is cmplete, click OK. 173

182 Backup The Avigiln Cntrl Center can be set t back up files autmatically, but yu can als back up files as needed frm the Back Up tab. Fr infrmatin abut cnfiguring the autmatic backup, see Changing Scheduled Backup Settings. Nte: Sme features are nt displayed if the server des nt have the required license, r if yu d nt have the required user permissins. Backing Up Recrded Vide On Demand The backup files are stred in a backup flder set by the Avigiln Cntrl Center Admin Tl. See the Avigiln Cntrl Center Server User Guide fr infrmatin abut changing the backup flder. 1. Select File > Backup... The Backup tab is displayed. 174

183 Backup Figure A. Backup tab 2. In the Camera(s) t Backup area, select all the cameras yu want t backup 3. In the Backup Optins area, set the time range yu want t backup. The time range is highlighted n the Timeline by the black time range markers. Yu can als drag the time range markers t change the time range. 4. Select the Delete ldest backups when disk full check bx t allw the applicatin t autmatically verwrite ld backup files when the backup flder is full. 5. Click Start Backup. Vide is always backed up in the Avigiln Backup (AVK) frmat. Yu can review the backed up vide in the Avigiln Cntrl Center Player. 175

184 Appendix Accessing the Web Client Yu can als access yur Avigiln High Definitin Surveillance System thrugh the Web Client. The Web Client is a simplified versin f the Client sftware. It allws yu t mnitr yur surveillance system, search fr vide events and exprt recrded vide utside the Client sftware. Be aware that yu cannt mdify any system settings thrugh the Web Client. Nte: The Web Client is nly cmpatible with the Internet Explrer brwser. T access the Web Client, yu need the Avigiln server's IP address and prt number. This infrmatin is available in the Avigiln Cntrl Center Admin Tl installed n the server. See the Avigiln Cntrl Center Server User Guide fr mre infrmatin. 1. T access the Web Client, pen Internet Explrer and enter the fllwing address: ip address>:<prt number>/ (Fr example, If yu have nt accessed the Web Client befre, yu may be prmpted t install the required plug-in sftware befre the Web Client will pen. 2. When the lgin screen appears, enter yur username and passwrd fr the server. The Web Client is pened in yur brwser, and yu can access the vide and cameras cnnected t the server. Nte: Yu can nly access ne server at a time thrugh the Web Client. 176

185 Appendix Figure A. Avigiln Cntrl Center Web Client Updating the Client Sftware Avigiln Cntrl Center Client sftware updates are typically included with the Avigiln Cntrl Center Server update packages. When yu first pen the Client sftware, the fllwing dialg bx will appear if a Client sftware update is available: 177

186 Avigiln Cntrl Center Enterprise Client User Guide Figure A. Update Cntrl Center Client Click the Update buttn t allw the Client sftware t update. The sftware update is autmatically dwnladed. The fllwing dialg bx will appear t shw the dwnlad prgress: Figure B. Update prgress When the update has finished dwnlading, click Update Cntrl Center. When the installatin wizard appears, fllw the prmpts t cmplete the update. Click D Nt Update t cntinue wrking with the Client sftware withut updating. The Client sftware will nt be updated, and yu can cntinue wrking with sftware as befre. The Client sftware can als be dwnladed frm the Sftware Dwnlad page f the Avigiln website: Supprted License Plates Here is a list f the license plates that are currently supprted by the Avigiln Cntrl Center License Plate Recgnitin (LPR) feature. If the license plate frmat yu need is nt listed, yu can Avigiln Technical Supprt at supprt@avigiln.cm and request an LPR Fnt Template. 178