Technical Manual. Mainboard D1483. English

Transcription

1 answers 2 Technical Manual Mainboard D1483 English

2 Are there any technical problems or other questions you need clarified? Please contact: your sales partner your sales outlet You will find further information in the manuals "Safety" and "Ergonomics". The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under:

3

4 Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Published by Fujitsu Siemens Computers GmbH Order No.: A26361-D1483-Z Printed in the Federal Republic of Germany AG /02 A26361-D1483-Z

5 English Mainboard D1483 Technical Manual November 2002 edition

6 Intel, Pentium and Celeron are registered trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification reserved. This manual was produced by cognitas. Gesellschaft für Technik-Dokumentation mbh

7 Contents Mainboard D Notational Conventions...1 Important Notes...2 Information about Boards...2 List of Features...3 Interfaces and connectors...4 Layout...4 External Connectors...5 Internal Connectors...6 LAN Connector A 10/ Ethernet Port (External)...6 LAN Connector B 1 GbE Ethernet Port (External)...6 System Fan 1/2 and CPU Fan 1/2 Connector (Internal)...7 PSU Fan Connector (CN15)...7 RSB Power Connector (CN5)...7 IPMI Connector (CN6)...7 UBS Port A/B - Dual Channel...8 Power Connector...8 Power Supply ATX Connector (Internal)...8 Floppy Connector...9 Intelligent Drive Electronics (IDE) Interface (Internal)...10 Temperature / System Monitoring...11 LAN Connector A 10/100 Mbit...11 LAN Connector B 1 GbE...12 PCI Bus Resources...13 PCI Slots...13 PCI IRQ Line X - Assignment of the PCI Interrupts...13 Screen Resolution...14 Jumper Settings...15 Clear CMOS - Jumper JP Power On Circuit - Jumper JP Boot Block - Jumper JP Add-On modules...16 Slot Sequence...16 Upgrading Main Memory...17 Replacing the Lithium Battery...18 Glossary...19 A26361-D1483-Z

8

9 Mainboard D1483 Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your system board. Further information Information on the BIOS Setup and additional descriptions of the drivers are contained in the readme files on your hard disk on the driver floppy disks included on the CD "Drivers & Utilities Collection" or "Drivers & Utilities" or "ServerStart". i The programme Acrobat Reader must be installed to be able to open the manuals. You may find the programme on the CD-ROM directory: utls/acrobat. For more details please read the according readme.txt files. Notational Conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.! i Supplementary information, remarks, and tips follow this symbol. Ê Text which follows this symbol describes activities that must be performed in the order shown. Ë This symbol indicates that you must enter a blank space (press the Space Bar) at this point. Ú This symbol indicates that you must press the Enter key. Text in this typeface indicates screen outputs. Text in this bold typeface indicates the entries you make via the keyboard. Text in italics indicates commands or menu items. "Quotation marks" indicate names of chapters or terms. A26361-D1483-Z English - 1

10 Important Notes Important Notes With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system. Connecting cables for peripherals must be adequately shielded to avoid interference. Observe the safety notes in the operating manual of your system.! Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-On modules" - "Replacing the Lithium Battery" section. Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. There is a danger of burns! The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the manual for the receiving device. i The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre. Information about Boards To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts. Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage. Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the mainboard or components on it, for example memory modules or processors. Never use sharp objects (screwdrivers) for leverage. Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown. When you handle boards fitted with ESDs, you must, under all circumstances, observe the following: You must always discharge static build up (e.g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges. Remove the power plug from the mains supply before inserting or removing boards containing ESDs. Always hold boards with ESDs by their edges. Never touch pins or conductors on boards fitted with ESDs. 2 - English A26361-D1483-Z

11 List of Features List of Features One processor slot for Pentium IV processors 1.7GHz and above with a 400/533 MHz Front Side Bus 512 Kbyte second level cache two 64 bit PCI slots with 33 MHz three memory slots (PC2100) registered up to a max. of 3 Gbytes main memory (LP DDR memory modules) Intel 82550PM ethernet LAN controller with 10/100 Mbits (RJ-45). Intel Ethernet LAN controller with 1 GbE (RJ-45). IDE RAID chip 20270; IDE hard disk controller connected to PCI bus ultra DMA 100 mode capable, supports PIO modes 0-4 Super I/O chip NS87414, floppy disk drive controller (possible formats: 720 Kbyte, 1.44 Mbyte and 2.88 Mbyte Northbridge; Server Works GC-SL Southbridge; Server Works CSB6 VRM 9.1 ATI Rage XL (4 Mbyte) EEPROM; SST (4 Mbyte) IPMI server management onboard System Monitoring Security Functions Simple error detection and correction in the main memory with an ECC (only for memory modules with ECC) System, setup and keyboard password Serial port can de deactivated Write protection for floppy disk drive Boot hard disk virus warning function Flash BIOS and EEPROMS (on the memory modules) virus protection function One external serial port (COM1) Three external USB ports (USB = Universal Serial Bus) Two external PS/2 interfaces for keyboard and mouse Real-time clock/calendar with integrated battery backup A26361-D1483-Z English - 3

12 The components and connectors marked are not necessarily present on the mainboard. Layout DIMM 1 DIMM 2 DIMM = RSB power connector 2 = IPMI connector 3 = Sys fan connector 1 4 = Sys fan connector 2 5 = FDD connector 6 = CN9 internal USB port 7 = CN8 connector for LED board / USB 8 = ATX power supply 9 = RAID secondary connector 10 = Power supply +12 V 11 = CPU fan connector 2 12 = RAID primary connector 13 = CPU fan connector 1 14 = IDE connector for CD-ROM/DVD drives 15 = 4 pin power connector JP4 A26361-D1483-Z English - 4

13 External Connectors = USB port (black) 2 = PS/2 mouse port (green) 3 = PS/2 keyboard port (purple) 4 = VGA port (blue) 5 = LAN connector A 10/100 Mbit 6 = LAN connector B 1 GbE 7 = Serial interface COM1 (turquoise) A26361-D1483-Z English - 5

14 Internal Connectors! Some of the following connectors are optional! LAN Connector A 10/ Ethernet Port (External) 1 Pin Signal 1 TX + 2 TX - 3 RX + 4 TERMPLANE 5 TERMPLANE 6 RX - 7 TERMPLANE 8 TERMPLANE LAN Connector B 1 GbE Ethernet Port (External) 1 Pin Signal 1 TX + 2 TX - 3 RX + 4 TERMPLANE 5 TERMPLANE 6 RX - 7 TERMPLANE 8 TERMPLANE 6 - English A26361-D1483-Z

15 System Fan 1/2 and CPU Fan 1/2 Connector (Internal) 1 (system fan - supervised) Pin Signal 1 GND 2 Controlled fan voltage (0 V, +6 V V) or Fix fan voltage (+12 V) 3 Sense PSU Fan Connector (CN15) 1 Pin Signal 1 GND 2 Controlled fan voltage (0 V, +6 V V) or Fix fan voltage (+12 V) RSB Power Connector (CN5) 1 Pin Signal 1 GND 2 VCC5SBY IPMI Connector (CN6) 1 Pin Signal 1 IPMBDAT 2 GRD 3 IPMBCLK 4 Not connected A26361-D1483-Z English - 7

16 UBS Port A/B - Dual Channel 1 2 (internal or external via special wire) Pin Signal Pin Signal 1 VCC Dual (max. 250 ma) 2 VCC Dual (max. 250 ma) 3 Reserved 4 Key 5 Power supply on (max. 1 second low pulse) 6 GND 7 Data positive 8 Data negative 9 GND 10 Over current (low asserted) Power Connector 1 2 Pin Signal 1 GND 2 GND V V Power Supply ATX Connector (Internal) 1 11 Pin Signal Pin Signal V V V V 3 GND 13 GND 4 +5 V 14 PS on (low asserted) 5 GND 15 GND 6 +5 V 16 GND 7 GND 17 GND 8 Powergood (high asserted) 18-5 V 9 +5 V Auxiliary V V V 8 - English A26361-D1483-Z

17 Floppy Connector 1 Pin Signal Pin Signal 1 VCC5 FDD 14 STEP# 2 INDEX# 15 GND 3 VCC5 FDD 16 WDATA# 4 DRV0# 17 GND 5 VCC5 FDD 18 WGATE# 6 DSKCHG# 19 GND 7 Not Connected 20 TRKO# 8 Not Connected 21 GND 9 Not Connected 22 WRTPRT# 10 MTRO# 23 GND 11 Not Connected 24 RDATA# 12 DIR# 25 GND 13 DENSEL 26 HDSEL# A26361-D1483-Z English - 9

18 Intelligent Drive Electronics (IDE) Interface (Internal) 1 2 Pin Signal Pin Signal 1 Reset drive (Low Asserted) 2 GND 3 Data 7 (High Asserted) 4 Data 8 (High Asserted) 5 Data 6 (High Asserted) 6 Data 9 (High Asserted) 7 Data 5 (High Asserted) 8 Data 10 (High Asserted) 9 Data 4 (High Asserted) 10 Data 11 (High Asserted) 11 Data 3 (High Asserted) 12 Data 12 (High Asserted) 13 Data 2 (High Asserted) 14 Data 13 (High Asserted) 15 Data 1 (High Asserted) 16 Data 14 (High Asserted) 17 Data 0 (High Asserted) 18 Data 15 (High Asserted)) 19 GND 20 Key 21 DRQ (High Asserted) 22 GND 23 I/O write (Low Asserted) 24 GND 25 I/O read (Low Asserted) 26 GND 27 I/O ready (High Asserted) 28 Cable select 29 DAK (Low Asserted) 30 GND 31 IRQ (High Asserted) 32 Not connected 33 ADR 1 (High Asserted) 34 ATA66 Detect (Low Asserted) 35 ADR 0 (High asserted) 36 ADR 2 (High Asserted) 37 CS 1 (Low asserted) 38 CS 3 (Low Asserted) 39 IDE-LED (Low asserted) 40 GND 10 - English A26361-D1483-Z

19 Temperature / System Monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating. In addition, any unnecessary noise is also prevented by reducing the fan speed and information is provided about the system status. The temperature and system monitoring are controlled by an onboard controller. The following functions are supported: Temperature Monitoring: Measurement of the processor and system temperature is done with an onboard temperature sensor; measurement of the ambient temperature is done with an external temperature sensor. Fan Monitoring: Fans that are no longer available; blocked or sticky fans that are detected are operated with a 12 V pulse voltage. Fans removed while the system is switched off are signalled by the Event LED. When the system is switched on again the BIOS processes the application. Fan Control: The four fans are regulated according to temperature. Sensor Monitoring: The removal of, or a faulty error within the system, detection is done by a temperature sensor. Should this happen all fans are monitored by this sensor and run at maximum speed, to achieve the greatest possible protection of the hardware. When the system is switched on again the BIOS processes the application. LAN Connector A 10/100 Mbit This system board has an Intel 82550PM LAN controller. The LAN controller is equipped with a 3 Kbyte transmission and receiving buffer (FIFO) and supports WOL function through Magic Packet. It is also possible to boot a device without its own boot hard disk via LAN. Here Bootix LAN BootP and Intel PXE are supported. The LAN RJ45 connector is equipped with a green and a yellow LED (light emitting diode). 1 = Green indicator 2 = Yellow indicator 1 2 LED 1 (left) LNK On The adapter is connected to a valid link partner. Off No link. ACT On (flashing) Data is being transmitted or received. 100 Green 100 Mbit/s A26361-D1483-Z English - 11

20 LED 2 (right) LNK On The adapter is connected to a valid link partner. Off No link. ACT On (flashing) Data is being transmitted or received. 10 Yellow 10 Mbit/s Green a connection exists (e.g. to a hub). Yellow Link Mode: the LAN connection is active. WOL mode: a Magic Packet TM is being received. LAN Connector B 1 GbE This system board has an Intel 82540PM LAN controller. The LAN controller is equipped with a 3 Kbyte transmission and receiving buffer (FIFO) and supports WOL function through Magic Packet. It is also possible to boot a device without its own boot hard disk via LAN. Here Bootix LAN BootP and Intel PXE are supported. The LAN RJ45 connector is equipped with a green and a bi-color (yellow/green) LED (light emitting diode). 3 = Green indicator 4 = Bi-color (yellow/green) indicator 1 2 LED 1 (left) LNK On The adapter is connected to a valid link partner. Off No link. ACT On (flashing) Data is being transmitted or received. LED 2 (right) 10/100/1000 Off 10 Mbit/s Green 100 Mbit/s Yellow 1000 Mbit/s 12 - English A26361-D1483-Z

21 PCI Bus Resources PCI Slots The following table shows an overview of the PCI slots: PCI slot 64bit Description Bus frequency 1 64 bit 64 bit PCI bus slot 33 MHz / 5 V 2 64 bit 64 bit PCI bus slot 33 MHz / 5 V PCI IRQ Line X - Assignment of the PCI Interrupts PCI IRQ Line x defines which ISA interrupts are used for the separate PCI slots. If you select Auto in the BIOS set up, the interrupts are assigned automatically and no further settings are required. Multifunctional PCI boards or boards with an integrated PCI-to-PCI bridge can use several PCI interrupts (INTA#, INTB#, INTC#, INTD#). Mono-functional PCI boards (default) only use one PCI interrupt (INTA#) per PCI slot. The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for every PCI slot. The same interrupt can be assigned simultaneously to several PCI boards. You should avoid this condition due to reduced performance. If you use a setting other than Auto, the Plug & Play functionality of the system BIOS for the corresponding PCI boards is deactivated. Auto The PCI interrupts are assigned automatically in accordance with the Plug & Play guidelines. Disabled No ISA interrupt is assigned to the PCI interrupt. 3, 4, 5, 7, 10, 11, 12, 14, 15 The selected ISA interrupt is assigned to the PCI interrupt. You may not select an ISA interrupt that is used by a component on the system board (e.g. controller) or an ISA board. IRQ Device IRQ 0 Timer output 0 IRQ 1 Keyboard IRQ 3 IRQ 4 Serial port 1 IRQ 6 Diskette IRQ 7 Printer Port IRQ 8 Real-time clock (RTC) IRQ 12 PS/2 mouse IRQ 13 Numeric processor IRQ 14 Embedded hard disk IDE 1 IRQ 15 Embedded hard disk IDE 1 A26361-D1483-Z English - 13

22 Screen Resolution Depending on the operating system used, the screen resolutions in the following table refer to the system board screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller. Screen resolution Refresh rate (Hz) Max. number of colours 640x ,7 mio. 800x ,7 mio. 1024x ,7 mio. 1057x ,7 mio. 1280x ,7 mio. ** Horizontal values tolerance ±0.3 khz. Shaded screen resolutions are not supported by LCD monitors (TFT) English A26361-D1483-Z

23 Jumper Settings DIMM 1 DIMM 2 DIMM 3 1 = JP1 Clear CMOS 2 = JP2 Power on circuit 3 = JP3 Boot block Clear CMOS - Jumper JP1 1-2 Normal CMOS setting (Default). CMOS will not be cleared (default entry). 2-3 CMOS settings are not cleared Power On Circuit - Jumper JP2 The system is powered on by one of the following mechanisms: IPMI or South Bridge. 1-2 Power on by IPMI (Default). 2-3 Power on by South Bridge. Boot Block - Jumper JP3 1-2 Normal (Default) 2-3 Boot Block A26361-D1483-Z English - 15

24 Add-On modules! For all steps described in this chapter pull the power plug out of the mains outlet! DIMM 1 DIMM 2 DIMM = Lithium battery 2 = PCI slot 2 (low profile) 3 = PCI slot 1 (riser card) for RSB 4 = Memory sockets Slot Sequence No sequence concern for PCI slots. Both PCI slots support 3.3 V operating voltage English A26361-D1483-Z

25 Upgrading Main Memory These slots are suitable for 128, 256, 512 and 1024 Mbyte LP DDR memory modules. The board supports a maximum of 3 Gbytes.! You may only use buffered 3.3 V memory modules. Unbuffered memory modules are not permitted. You may only use unstacked modules. LP DDR memory modules must be designed for a clock frequency of 133 MHz (meets PC2100 specification). Installing a Memory Module 2 2 Ê Ê Push the holders on each side of the memory compartment outwards. Insert the memory module in the slot while folding the side holders up until the memory module engages (2). Removing a Memory Module 1 1 Ê Push the clips on the right and left of the compartment outward (1). Ê Carefully remove the memory module from the compartment (2). A26361-D1483-Z English - 17

26 Replacing the Lithium Battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. Incorrect replacement of the lithium battery may lead to a risk of explosion!! The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. The plus pole must be on the top! The lithium battery holder exists in different designs that function in the same way Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Ê Remove the battery (2). Ê Push the new lithium battery of the identical type into the holder (3) and press it downward until it engages (4) English A26361-D1483-Z

27 Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described mainboard. ACPI Advanced Configuration and ISA Industrial Standard Architecture Power Management Interface AC'97 Audio Codec '97 LAN Local Area Network AGP Accelerated Graphics Port LSA LAN Desk Service Agent AMR Audio Modem Riser MCH Memory Controller Hub AOL Alert On LAN MMX MultiMedia extension APM Advanced Power Management P64H PCI64 Hub ATA Advanced Technology Attachment PCI Peripheral Component Interconnect BIOS Basic Input Output System PXE Preboot execution Environment BMC Baseboard management RAM Random Access Memory controller CAN Controller Area Network RAMDAC Random Access Memory Digital Analogue Converter CPU Central Processing Unit RDRAM Rambus Dynamic Random Access Memory CNR Communication Network Riser RIMM Rambus Inline Memory Module C-RIMM Continuity Rambus Inline RTC Real Time Clock Memory Module DIMM Dual Inline Memory Module SB Soundblaster ECC Error Correcting Code SDRAM Synchronous Dynamic Random Access Memory EEPROM Electrical Erasable Programmable Read Only Memory SGRAM Synchronous Graphic Random Access Memory FDC Floppy disk controller SIMD Streaming Mode Instruction (Single Instruction Multiple Data) FIFO First-In First-Out SMBus System Management Bus FSB Front Side Bus SVGA Super Video Graphic Adapter FWH Firmware Hub USB Universal Serial Bus GMCH GPA I 2 C IAPC ICH IDE IPSEC Graphics and Memory Controller Hub Graphics Performance Accelerator Inter Integrated Circuit Instantly Available Power Managed Desktop PC Design I/O Controller Hub Intelligent Drive Electronics Internet Protocol Security VGA WOL Video Graphic Adapter Wake On LAN A26361-D1483-Z English - 19

28 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed. Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions. Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the The Internet pages of Fujitsu Technology Solutions are available at and the user documentation at Copyright Fujitsu Technology Solutions, 2009 Hinweise zum vorliegenden Dokument Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions. Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion. Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind. Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Die Internetseiten von Fujitsu Technology Solutions finden Sie unter und unter finden Sie die Benutzerdokumentation. Copyright Fujitsu Technology Solutions, 2009