PRIMERGY BX630 S2 Scalable Server Blade. Options Guide

Transcription

1 PRIMERGY BX630 S2 Scalable Server Blade Options Guide Edition October 2007

2 Comments Suggestions Corrections The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Feel free to send us your comments by to Certified documentation according to DIN EN ISO 9001:2000 To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001:2000. cognitas. Gesellschaft für Technik-Dokumentation mbh Copyright and Trademarks Copyright 2007 Fujitsu Siemens Computers GmbH. All rights reserved. Delivery subject to availability; right of technical modifications reserved. All hardware and software names used are trade names and/or trademarks of their respective manufacturers.

3 Contents 1 Preface Concept and target groups Documentation overview Extensions and conversions Structure of the server blade Configurations Notational conventions Procedure Safety instructions Preparation Processors Installing a second processor Memory Fitting rules Replacing memory modules Optional I/O module Installing an I/O daughter card BX630 S2 Options Guide

4 Contents 8 Replacing the battery Upgrading to a quad-socket server blade Overview Assembly instructions Completion Closing the server blade Abbreviations Index Options Guide BX630 S2

5 1 Preface The PRIMERGYBX630 S2 scalable server blade is an AMD-based server blade designed for the PRIMERGY BX600 S3 basic unit. It can also be operated in slots 1-3 and 5-9 of the BX600 S2 basic unit. The BX630 S2 scalable server blade can be installed as a dual-socket server blade or, in a multi-blade configuration, as a quad-socket server blade. 1.1 Concept and target groups This Options Guide shows you how to extend and upgrade your server. V CAUTION! The activities described in this manual may only be performed by technical specialists. I The installation and removal of the hot-plug components is described in the Operating Manual supplied with the server. 1.2 Documentation overview More information on your PRIMERGY BX630 S2 can be found in the following documents: Quick Start Software - Quick Installation Guide leaflet (only included as a printed copy) Safety notes and other important information manual Warranty manual Ergonomics manual Returning used devices manual Helpdesk leaflet PRIMERGY BX630 S2 Server Operating Manual I PRIMERGY manuals are available in PDF format on the ServerBooks DVD. The ServerBooks DVD is part of the ServerStart Suite supplied with every server. BX630 S2 Options Guide 5

6 Documentation overview Preface The PDF files of the manuals can also be downloaded free of charge from the Internet. The overview page showing the online documentation available on the Internet can be found using the URL: The PRIMERGY server documentation can be accessed using the Industry standard servers navigation option. If you need a replacement copy of the ServerBooks DVD, send the details of your server to the following address: Reklamat-PC- LOG@fujitsu-siemens.com Further sources of information: Manual for the monitor Documentation for boards and drives Documentation for your operating system Information files on your operating system 6 Options Guide BX630 S2

7 Preface Extensions and conversions 1.3 Extensions and conversions Second processor If only one processor is installed in your server blade, you can upgrade it to include a second one. You may only use processors of the same type in the server blade. The second processor must have the same clock frequency as the first. Extending the main memory The system board of the BX630 S2 scalable server blade has four memory banks with two 184-pin DDR2 DIMM slots each. This allows a maximum memory configuration of 32 GB. Each memory bank can be fitted with 512 Mbyte, 1 Gbyte, 2 Gbyte or 4 Gbyte registered DDR2 667 MHz PC memory modules. The two memory modules of one bank must always be fitted in pairs and have the same capacity. Optional I/O module The server blade can be equipped with a 4-Gbit FC I/O module or a 1-Gbit Ethernet I/O module. To allow use of the additional I/O functionality, at least one FC pass-thru blade (or switch blade) or Ethernet LAN pass-thru blade (or switch blade) must be installed in the NET3 and/or NET4 slots of the PRIMERGY BX600 basic unit. Multi-blade configuration You can upgrade the BX630 S2 scalable server blade to a quad-socket server blade by connecting two dual-socket server blades, see section Configurations on page 10. BX630 S2 Options Guide 7

8 Structure of the server blade Preface 1.4 Structure of the server blade Figure 1: PRIMERGYBX630 S2 scalable server blade The above figure shows the positions of the most important components of the PRIMERGYBX630 S2 scalable server blade. 8 Options Guide BX630 S2

9 Preface Structure of the server blade 1 CPU 1 and heat sink 2 DIMM slots for four DDR2 667 modules (two banks, assigned to CPU1) 3 Lithium battery 4 DIMM slots for four DDR2 667 modules (two banks, assigned to CPU2) 5 DIP switch SW4 (user switch) 6 Control panel board with connection cable inch SAS/SATA-II hard disk module inch SAS/SATA-II hard disk module 2 9 CPU 2 and heat sink 10 Position for a 4-Gbit FC daughter card or a 1-Gbit Ethernet daughter card (optional I/O module) BX630 S2 Options Guide 9

10 Configurations Preface 1.5 Configurations The PRIMERGY BX630 S2 scalable server blade can be installed as a dualsocket server blade or as a quad-socket server blade. The possible configurations are shown in the following diagrams. Dual-socket server blade Opteron CPU 2 Bank 4 (2 modules) Bank 3 (2 modules) FC or GbE I/O module or emtpy SAS/SATA 2.5" HDD module or dummy module Opteron CPU 1 Bank 2 (2 modules) Bank 1 (2 modules) SAS/SATA controller onboard SAS/SATA 2.5" HDD module or dummy module Processor Main memory I/O module Hard disks Basic configuration Optional module Figure 2: PRIMERGY BX630 S2 dual-socket server blade 10 Options Guide BX630 S2

11 Preface Configurations Quad-socket server blade The following figure shows the possible configurations of a PRIMERGY BX630 S2 quad-socket server blade. Master Opteron CPU Bank 1 (2 modules) Bank 2 (2 modules) FC or GbE I/O module or empty SAS 2.5" HDD module or dummy module Opteron CPU Bank 3 (2 modules) Bank 4 (2 modules) SAS/SATA controller onboard SAS 2.5" HDD module or dummy module Slave Opteron CPU Bank 5 (2 modules) Bank 6 (2 modules) FC or GbE I/O module or empty SAS 2.5" HDD module or dummy module Opteron CPU Bank 7 (2 modules) Bank 8 (2 modules) SAS/SATA controller onboard SAS 2.5" HDD module or dummy module Processor Main memory I/O module Hard disks Basic configuration Optional module Figure 3: PRIMERGY BX630 S2 quad-socket server blade BX630 S2 Options Guide 11

12 Notational conventions Preface 1.6 Notational conventions The following notational conventions are used in this manual: Text in italics Quotation marks V CAUTION! I indicates commands or menu items. indicate names of chapters and terms that are being emphasized. describes activities that must be performed in the order shown. pay particular attention to texts marked with this symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data. indicates additional information, notes and tips. 12 Options Guide BX630 S2

13 2 Procedure V CAUTION! The actions described in this manual should only be performed by technical specialists. Equipment repairs should only be performed by service staff. Any failure to observe the guidelines in this manual, and any unauthorized opening or improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment. Please note that any unauthorized opening of the server will void the warranty and exempt the manufacturer from all liability. First of all please familiarize yourself with the safety instructions in the chapter Safety instructions on page 15. Make sure that all the manuals you need are available and print out the PDF files if necessary. You will definitely need the operating manuals of the server blade and of your BX600 S2 or BX600 S3 basic unit. Shut down the server blade correctly, switch it off and remove it from the basic unit as described in the Completion. Extend or upgrade your server blade as described in the relevant chapter. I The installation and removal of the hot-plug components is described in the Operating Manual supplied with the server blade. Close the server blade, place it back in the basic unit and switch on the server blade as described in chapter Completion on page 57. Start the operating system and, if necessary, configure it as required (see the Operating Manual). BX630 S2 Options Guide 13

14

15 3 Safety instructions I The following safety instructions are also provided in the manual Safety notes and other important information. This device meets the relevant safety regulations for IT equipment. If you have any questions about whether you can install the server in the intended environment, please contact your sales outlet or our customer service team. V CAUTION! The actions described in this manual should only be performed by technical specialists. Equipment repairs should only be performed by service staff. Any failure to observe the guidelines in this manual, and any unauthorized opening or improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment. Please note that any unauthorized opening of the server will void the warranty and exempt the manufacturer from all liability. Before starting up V CAUTION! During installation and before operating the device, observe the instructions on environmental conditions for your device. If the device is brought in from a cold environment, condensation may form both inside and on the outside of the device. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. Transport the device only in the original packaging or in packaging that protects it from knocks and jolts. Installation and Operation V CAUTION! Read the notes on installation and operation in the operating manual for your BX600 S2 or BX600 S3 basic unit. BX630 S2 Options Guide 15

16 Safety instructions V CAUTION! When installing the server blade in the basic unit, beware of the energy hazard at the midplane contacts. A short-circuit on these contacts may damage the system. Data cables must be adequately shielded to avoid interference. For the LAN wiring, the requirements according to standards EN and EN /2 apply. The minimum requirement is the use of a protected LAN line of category 5 for 10/100 Mbps Ethernet, and/or category 5e for Gigabit Ethernet. The requirements of the specification ISO/IEC must also be taken into account. Route the cables in such a way that they do not form a potential hazard (tripping) and cannot be damaged. When connecting the device, refer to the relevant notes in the Operating Manual. Do not connect or disconnect any data transmission cables during a thunderstorm (lightning hazard). Be careful to ensure that no objects (e.g. jewelry, paper clips etc.) or liquids get inside the device (electric shock, short circuit). In emergencies (e.g. damaged casing, control elements or cables, penetration of liquids or foreign bodies), switch off the device immediately, unplug it from the grounded power outlets, and contact your customer service center. Proper operation of the device (in accordance with IEC60950/EN 60950) is only ensured if the casing is completely assembled and the rear covers for the installation openings are in place (electric shock, cooling, fire protection, interference suppression). Install only system extensions that satisfy the requirements and rules governing safety, electromagnetic compatibility, and telecommunications terminal equipment. If you install other extensions, you may damage the system or violate these safety regulations. Information on which system extensions are suitable can be obtained from the customer service center or your sales outlet. 16 Options Guide BX630 S2

17 Safety instructions V CAUTION! The components marked with a warning label (e.g. lightning symbol) may only be opened, removed, or exchanged by authorized, qualified personnel, with the exception of the hot-plug/hot-swap components. If you cause a defect on the device by installing or exchanging system extensions, the warranty will be invalidated. Only set the resolutions and refresh rates specified in the operating manual for your monitor. Batteries V CAUTION! Otherwise, you may damage the monitor. If you are in any doubt, contact your sales outlet or customer service center. Incorrect replacement of batteries can lead to risk of explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer (see Options Guide). Do not throw batteries into the trash can. They must be disposed of in accordance with local regulations on special waste. The German battery act obligates consumers in Germany to return waste batteries to the distributor or to the return points established by the public waste management authorities. Replace the lithium battery on the system board only as described in the Options Guide. All batteries containing pollutants are marked with a crossed-out garbage can accompanied by the chemical symbol of the heavy metal that classifies the battery as a pollutant: Cd Cadmium Hg Mercury Pb Lead BX630 S2 Options Guide 17

18 Safety instructions Modules with electrostatic-sensitive components Systems and components that might be damaged by electrostatic discharge (ESD) are marked with the following label: Figure 4: ESD label When you handle components fitted with ESDs, you must observe the following points under all circumstances: Remove the power plug before installing or removing components containing ESDs. You must always discharge yourself of static charges (e.g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges. Only touch the components at the positions highlighted in green (touch points). Do not touch any exposed pins or conductors on a component. Use a grounding cable designed for this purpose to connect yourself to the system unit as you install components. Place all components on a static-safe base. I You will find a detailed description for handling ESD components in the relevant European or international standards (DIN EN , ANSI/ESD S20.20). 18 Options Guide BX630 S2

19 4 Preparation V CAUTION! Please observe the safety information in the chapter Safety instructions on page 15. Exit all applications and shut down the server blade correctly. Press the On/Off button on the server blade control panel. Removing the server blade from the basic unit 2 1 Press the two touch points (1) to unlock the handles. Open out the two handles (2) simultaneously to disengage the server blade. 1 2 Figure 5: Disengaging the server blade BX630 S2 Options Guide 19

20 Preparation Pull the server blade out of the basic unit. Figure 6: Removing the server blade from the basic unit 20 Options Guide BX630 S2

21 Preparation Removing the housing cover Figure 7: Removing the housing cover Undo the two knurled screws (1). Push the housing cover as far as possible in the direction of the arrow (2). Take off the housing cover. The server blade components are now freely accessible (see figure 1 on page 8). BX630 S2 Options Guide 21

22

23 5 Processors V CAUTION! Make sure you observe the safety notes in the chapter Safety instructions on page 15. Processors are components which are extremely sensitive to electrostatic discharge and must be handled with caution. When you take a processor out of its protective wrapper or out of a socket, place it on an insulated, antistatic surface with the smooth side down. Never slide a processor over a surface. 5.1 Installing a second processor The BX630 S2 dual-socket server blade can be upgraded with a second processor. The upgrade kit includes a processor and a heat sink. V CAUTION! Always use processors of the same type. All processors must have the same frequency and cache size. For multi-processor mode use a suitable multi-processor operating system. Open the server blade as described in the chapter Preparation on page 19. I The BX630 S2 server blades may have two different processor sockets, see figure 8: BX630 S2 Options Guide 23

24 Installing a second processor Processors Foxconn processor socket Figure 8: Processor socket variants Tyco processor socket The following section describes how to install a processor in the Foxconn processor socket. Differences in handling a Tyco processor socket are indicated in the relevant steps. 2 1 Figure 9: Processor socket variant 1: Opening the socket Remove the protective cover by lifting it at the edge (1). Release the locking lever (2) by first pressing it down and then swiveling it up as far as it will go. 24 Options Guide BX630 S2

25 Processors Installing a second processor Figure 10: Processor socket variant 1: Opening the locking frame Swivel the locking lever of the processor socket upward. Remove the processor from its protective wrapper. BX630 S2 Options Guide 25

26 Installing a second processor Processors A Figure 11: Inserting the processor (Foxconn socket) Position the new processor above the socket, and press it carefully into the socket. V CAUTION! The processor can only be installed in one direction. Make sure that the recesses on the processor (A) are aligned with the corresponding positioning elements (lugs) on the socket. I The Tyco processor socket only has positioning elements on one side, see (A) in figure 12. Figure 12: Processor socket variant 2: Inserting the processor A 26 Options Guide BX630 S2

27 Processors Installing a second processor 1 Figure 13: Locking the processor (Foxconn socket) Fold the locking frame of the processor socket down. Swivel the locking lever of the socket down. Lock the locking lever by pressing it under the bracket (1) on the processor socket. BX630 S2 Options Guide 27

28 Installing a second processor Processors V CAUTION! When locking the Tyco processor socket, make sure that the small clips on the locking frame (A) slide under the corresponding brackets on the outer socket frame, see figure 14. A Figure 14: Locking the processor (Tyco processor socket) 28 Options Guide BX630 S2

29 Processors Installing a second processor Installing the heat sink Figure 15: Preparing the heat sink Remove the yellow tape from the underside of the heat sink, and then remove the transparent cover protecting the thermal paste. BX630 S2 Options Guide 29

30 Installing a second processor Processors Figure 16: Fastening the heat sink Place the heat sink on the processor and fix it with the three supplied screws. Fasten the screws in the order shown in the figure. 30 Options Guide BX630 S2

31 6 Memory The system board of the PRIMERGYBX630 S2 scalable server blade has four memory banks, comprising eight slots, which can be fitted in pairs with 512 MB, 1 GB, 2 GB or 4 GB DDR2 667 memory modules. The board supports a maximum memory configuration of 32 GB. Figure 17: PC3200 DDR SDRAM module A The memory modules are marked with a dent (A) so that you cannot install them the wrong way round. BX630 S2 Options Guide 31

32 Fitting rules Memory 6.1 Fitting rules DIMM 1 DIMM 2 DIMM 3 DIMM 4 CPU 1 DIMM 5 DIMM 6 DIMM 7 DIMM 8 CPU 2 Figure 18: Slot numbering for memory modules Slots DIMM 1 through DIMM 4 are assigned to CPU1. Slots DIMM 5 through DIMM 8 are assigned to CPU 2, i.e. they can only be fitted if CPU 2 is installed. The following rules also apply: The DIMM slots must be fitted one bank at a time. A memory bank comprises two DIMM slots. The two DIMM modules of one bank must have the same type (identical capacity, identical clock rate, single ranked or dual ranked). If only CPU 1 is installed: Start with DIMM 1+2 followed by DIMM 3+4. If CPU 1 and CPU 2 are installed: Start with DIMM 1+2 followed by DIMM 5+6, then DIMM 3+4 followed by DIMM Options Guide BX630 S2

33 Memory Fitting rules If you have a quad-socket configuration: Start with DIMM 1+2 followed by DIMM 5+6 in the master module, then DIMM 1+2 followed by DIMM 5+6 in the slave module. Install additional DIMMs in DIMM 3+4 followed by DIMM 7+8 in the master module, followed by DIMM 3+4 and DIMM 7+8 in the slave module. If you install memory modules for a CPU which have different memory capacities, you must first install the modules with the lower memory capacity. BX630 S2 Options Guide 33

34 Replacing memory modules Memory 6.2 Replacing memory modules V CAUTION! Note the safety instructions and the information on handling electrostatically sensitive devices on page 18. Install the memory modules very carefully. Too much pressure can damage the ejection tabs. Remove the server blade from the basic unit and open it as described in the chapter Preparation on page Figure 19: Removing a memory module Fold the tabs outwards on both sides of the relevant slot (1). If a memory module was already installed in the slot: Remove the memory module from the slot (2). 34 Options Guide BX630 S2

35 Memory Replacing memory modules Figure 20: Installing a memory module Carefully press the memory module into the slot (1) until the fastening tabs on both sides of it engage (2). Close the server blade, insert it in the basic unit and switch it on as described in chapter Completion on page 57. BX630 S2 Options Guide 35

36

37 7 Optional I/O module The PRIMERGYBX630 S2 dual-socket server blade can be equipped with an additional I/O module. For this purpose, the server blade has a special slot for an extension board (I/O daughter card) (see figure 24 on page 41). The following I/O daughter cards are available for the BX630 S2 server blade: 4-Gbit Fibre Channel daughter card (PCIe) 1-Gbit Ethernet daughter card (PCIe) 10-Gbit Ethernet daughter card (PCIe) I To allow use of the additional I/O functionality, at least one FC I/O blade or an Ethernet I/O blade must be installed in slot NET3 and/or NET4 of the PRIMERGY BX600 S2 or BX600 S3 basic unit. For further information on I/O blades, see the operating manual for your basic unit. It is not possible to mix Fibre Channel I/O blades and Ethernet I/O blades in slots NET3 and NET4 of the basic unit. BX630 S2 Options Guide 37

38 Optional I/O module 4-Gbit Fibre Channel daughter card (PCIe) Figure 21: 4-Gbit Fibre Channel daughter card (PCIe) The 4-Gbit FC daughter card (PCIe) provides two independent serial 1/2/4- Gbit/s FC ports. It is fitted with an Emulex chip and supports multiple FC storage subsystems of the corresponding versions. I The 4-Gbit FC daughter card can only be used in combination with the 4/4-Gbit FC switch blade. For more information, see the BX600 S3 operating manual. The 4-Gbit FC option is only supported by the BX600 S3 basic unit. 38 Options Guide BX630 S2

39 Optional I/O module 1-Gbit Ethernet daughter card (PCIe) Figure 22: Gbit Ethernet daughter card (PCIe) The 1-Gbit Ethernet daughter card (PCIe) has two Broadcom 5708S chips and provides two 1-Gbit/s Ethernet ports. TOE (TCP/IP Offload Engine) and iscsi/iscsi Boot are supported. BX630 S2 Options Guide 39

40 Optional I/O module 10-Gbit Ethernet daughter card (PCIe) Figure 23: 10-Gbit Ethernet daughter card (PCIe) The 10-Gbit Ethernet daughter card (PCIe) provides two 10-Gbit/s Ethernet ports. This module also supports TOE (TCP/IP Offload Engine) and iscsi/iscsi Boot. I The 10-Gbit Ethernet daughter card (PCIe) can only be used in combination with the 10-Gbit switch blade 10/2. For further information, see the operating manual for your BX600 S2 or BX600 S3 basic unit. 40 Options Guide BX630 S2

41 Optional I/O module Installing an I/O daughter card 7.1 Installing an I/O daughter card V CAUTION! Please observe the safety information in the chapter Safety instructions on page 15 Remove the server blade from the basic unit and open it as described in the chapter Preparation on page 19. A Figure 24: Position for an I/O daughter card Place the I/O daughter card onto the two sockets (A). Fasten the I/O daughter card with three screws. The corresponding nuts on the system board are indicated by arrows in figure 24. BX630 S2 Options Guide 41

42

43 8 Replacing the battery To allow permanent saving of the system information, a lithium battery is installed which supplies the CMOS memory with power. If the battery charge is too low or the battery is empty, a corresponding error message is displayed. In this case, the lithium battery must be replaced. V CAUTION! Observe the safety notes and the information on handling batteries in the section Batteries on page 17. Incorrect replacement of batteries may result in a risk of explosion. The batteries must be replaced with an identical battery or with a battery type recommended by the manufacturer. Make sure you insert the battery correctly. The positive pole must face toward the inside of the server blade Figure 25: Replacing the battery Press the locking lever in the direction of the arrow (1) and remove the battery from its carrier (2). Insert a new lithium battery of identical type into the carrier (3) and engage it with the lever (4). BX630 S2 Options Guide 43

44

45 9 Upgrading to a quad-socket server blade This chapter describes how to connect two BX630 S2 dual-socket server blades to form a quad-socket server blade. 9.1 Overview A Figure 26: PRIMERGY BX630 S2 quad-socket server blade The above figure shows a BX630 S2 quad-socket server blade as it is installed in the BX600 S2 or BX600 S3 basic unit. The master module is on the right side, identifiable by the handles and the control elements (A) on the control panel board. The slave module has the handles removed and the control panel has been replaced by a dummy module. The slave module has a fixed connection to the housing cover of the master module. The two modules of the quad-socket server blade exchange data through small circuit boards with printing on both sides, see Quad-socket upgrade kit. I In a PRIMERGY BX630 S2 quad-socket server blade, only processors of the Opteron 83xx MP series are allowed. BX630 S2 Options Guide 45

46 Overview Upgrading to a quad-socket server blade Quad-socket upgrade kit The quad-socket upgrade kit for connecting two PRIMERGY BX630 S2 dualsocket server blades to form a quad-socket server contains the following elements. Figure 27: Side-band element The side-band element connects the server management bus of the master module to that of the slave module, see also Inserting the HT-link elements and the side-band element on page 53. Figure 28: HT-link element Two HyperTransport link elements (HT-link elements) connect the system bus of the master module and the system bus of the slave module, see also Inserting the HT-link elements and the side-band element on page Options Guide BX630 S2

47 Upgrading to a quad-socket server blade Assembly instructions Figure 29: Guide element for HT-link elements and side-band elements and countersunk screws. Three plastic guide elements ensure the exact positioning of the HT-link elements and side-band elements during installation. These guide elements are fastened to the housing cover of the master module, see also Preparing the housing cover of the master module on page 50. Figure 30: Shoulder screws for fastening the slave module The slave module is fastened to the housing cover of the master module with 5 shoulder screws, see also page Assembly instructions The following section describes the steps you need to perform to upgrade the server blade to a quad-socket server blade. The links take you to the sections with the descriptions of the individual steps. Removing the handles of the slave module Removing the control panel board of the slave module Preparing the housing cover of the master module Fastening the housing cover of the master module to the slave module Closing the master module Inserting the HT-link elements and the side-band element BX630 S2 Options Guide 47

48 Assembly instructions Upgrading to a quad-socket server blade Removing the handles of the slave module The quad-socket server blade is locked in the BX600 S2 or BX600 S3 basic unit using the handles of the master module. You must remove the handles of the slave module. A Figure 31: Removing the handles Remove the housing cover of the slave module, see page 21. Undo the pins of the joints (A) with a Philips screwdriver and remove them from the housing. Remove the handles. Removing the control panel board of the slave module Figure 32: Control panel board with connection cable 48 Options Guide BX630 S2

49 Upgrading to a quad-socket server blade Assembly instructions The quad-socket server blade is controlled via the control panel of the master module. You must remove the control panel board of the slave module. 2 1 Figure 33: Removing the control panel board Undo the two screws (1) fastening the control panel board to the server blade housing. Loosen the clamping bracket (2) and disconnect the cable of the control panel board from the connector on the system board. Figure 34: Removing the control panel board Remove the control panel board with the connection cable from the server blade housing. BX630 S2 Options Guide 49

50 Assembly instructions Upgrading to a quad-socket server blade Preparing the housing cover of the master module Mount the guides for the exact positioning of the HT-link elements and the sideband element on the underside of the master module housing cover figure 35 shows a prepared housing cover. Figure 35: Housing cover of the master module (underside with guides for the link elements) Remove the housing cover of the master module, see page 21. Figure 36: Housing cover of the master module with guide elements Fasten each guide element with two countersunk screws. 50 Options Guide BX630 S2

51 Upgrading to a quad-socket server blade Assembly instructions Fastening the housing cover of the master module to the slave module Figure 37: Fastening the housing cover of the master module to the slave module Place the prepared housing cover of the master module on the underside of the slave module. Fasten the housing cover of the master module with 5 screws. The screw holes are indicated by arrows in figure 37. BX630 S2 Options Guide 51

52 Assembly instructions Upgrading to a quad-socket server blade Closing the master module A Figure 38: Closing the master module Turn the slave module over so that the housing cover of the master module and the guide elements face down. Carefully place the slave module onto the housing of the master module such that it projects 1-2 cm at the back. Make sure that the slave module lies flush with both sides of the master module. Push the slave module in the direction of the arrow as far as it will go. Fasten the two green knurled screws (A). 52 Options Guide BX630 S2

53 Upgrading to a quad-socket server blade Assembly instructions Inserting the HT-link elements and the side-band element The two modules of the quad-socket server blade exchange data through two HT-link elements and the side-band element. These double-sided printed circuit boards are plugged into special sockets on the system boards and connect the bus systems of the two modules Figure 39: Connection with an HT-link element The figure above shows a diagram of the connection between the system board of the master module (1) and the system board of the slave module (2) by way of an HT-link element (3). BX630 S2 Options Guide 53

54 Assembly instructions Upgrading to a quad-socket server blade The figure below shows the positions of the sockets for the HT-link elements (a, b) and the side-band element (c) on the BX630 S2 system board. c CPU1 a CPU2 Figure 40: Position of the sockets for the HT-link and side-band elements V CAUTION! Make sure you insert the link elements with the correct side facing the front as shown in the following figures. b 54 Options Guide BX630 S2

55 Upgrading to a quad-socket server blade Assembly instructions B A Figure 41: Inserting the side-band element Insert the side-band element in the socket (A). The metal edge (B) must face inward. Figure 42: Installed side-band element Carefully press the side-band element down as far as it will go. BX630 S2 Options Guide 55

56 Assembly instructions Upgrading to a quad-socket server blade A A Figure 43: Installing the HT-link elements Insert the HT-link elements in the sockets. The metal edges (A) must face outward. Figure 44: Installed HT-link elements Carefully press the HT-link elements down as far as they will go. This completes the upgrade to a quad-socket server blade. Now proceed as described in the chapter Completion on page Options Guide BX630 S2

57 10 Completion V CAUTION! Please observe the safety information in the chapter Safety instructions on page Closing the server blade Figure 45: Closing the housing cover Place the housing cover onto the server blade such that it projects 1-2 cm at the back. Push the housing cover forward as far as possible (1). Fasten the two green knurled screws (2). Insert the server blade in the basic unit. I To install the server blade in the basic unit, perform the procedure described in the chapter Preparation on page 19 in reverse. BX630 S2 Options Guide 57

58

59 Abbreviations ASR&R Automatic Server Reconfiguration and Restart ATA BIOS CD COM CPU Advanced Technology Attachments Basic Input-Output System Compact Disk Communication Central Processing Unit DBMS Database Management System DDR Double Data Rate (RAM) DIMM Dual Inline Memory Module DVD ECC EDC EMC Digital Versatile Disk Error Correcting Code Error Detection Code Electromagnetic Compatibility BX630 S2 Options Guide 59

60 Abbreviations ESD FC GAM HDD HU I/O ID IDE IP Electrostatic Discharge Fibre Channel Global Array Manager Hard Disk Drive Height Unit Input/Output Identification Integrated Drive Electronics Internet Protocol iscsi Internet SCSI LAN LCD LED MRL Local Area Network Liquid Crystal Display Light-Emitting Diode Manually Retention Latch 60 Options Guide BX630 S2

61 Abbreviations NIC NMI PCI PDA Network Interface Card Non Maskable Interrupt Peripheral Component Interconnect Prefailure Detection and Analyzing POST Power On Self Test PSU RAID ROM SAN SAS SATA SCA SCSI SCU Power Supply Unit Redundant Arrays of Independent Disks Read-Only Memory Storage Area Network Serial Attached SCSI Serial ATA Single Connector Attachment Small Computer System Interface Server Configuration Utility BX630 S2 Options Guide 61

62 Abbreviations SFP USB VGA VPD WOL Small Form Factor Pluggable Universal Serial Bus Video Graphics Adapter Vital Product Data Wakeup on LAN 62 Options Guide BX630 S2

63 Index B battery replace 43 server blade 43 D documentation overview 5 E ESD (devices sensitive to electrostatic discharge) 18 Ethernet optional I/O module 37 F Fibre Channel optional I/O module 37 fitting rules SDRAM modules 32 H HT-link element 46 I I/O daughter card 37 1-Gbit Ethernet (PCIe) 39 4-Gbit Fibre Channel (PCIe) 38 information material, additional 6 L Lithium battery 17 lithium battery 43 O optional I/O module 37 P processor add 7 Q quad-socket upgrade assembly instructions overview 45 upgrade kit 46 R replace battery 43 S SDRAM 31 fitting rules 32 server blade battery 43 close 57 open 21 remove from basic unit 19 side-band element 46 slave module, prepare remove control panel board 48 remove handles 48 T target group 5 M main memory extend 7 meaning of the symbols 12 N notational conventions 12 BX630 S2 Options Guide 63

64

65 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed. Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions. Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the The Internet pages of Fujitsu Technology Solutions are available at and the user documentation at Copyright Fujitsu Technology Solutions, 2009 Hinweise zum vorliegenden Dokument Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions. Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion. Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind. Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Die Internetseiten von Fujitsu Technology Solutions finden Sie unter und unter finden Sie die Benutzerdokumentation. Copyright Fujitsu Technology Solutions, 2009