This symbol is followed by supplementary information, remarks and tips.

Transcription

1 Introduction This Technical Manual describes the system boards of the PRIMERGY 870 server systems, which can be equipped with up to four Intel Xeon processors. You may find further information in the description "BIOS Setup". Further information to drivers is provided in the readme files on hard disk or on the supplied drivers diskettes or on the "Drivers & Utility" or "ServerStart" CD. Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to texts marked with this symbol. Failure to observe this warning endangers your life, destroys the system, or may lead to loss of data.! i This symbol is followed by supplementary information, remarks and tips. ² Texts which follow this symbol describe activities that must be performed in the order shown. Texts in italics indicate commands or menu item. "Quotation marks" indicate names of chapters and terms that are being emphasized. Overview The PRIMERGY 870 server systems mainly consist of the following plug-in boards: I/O board Processor board Memory board (2x) Interface board SCSI board (3x) Power supply board ECU board Drive board (2x) U41029-J-Z English - 1

2 Introduction Abbreviations Abbreviations ASIC ASR&R BIOS CAN CPU DAC DIMM DIP DMA ECU EDO-DRAM FPM I 2 O IDE ISA ISP LAN LCD LED LVD MINT OLR PIIX4 PCI PIO PXB RTC RTDS SAF-TE SCA SCSI SE STM USB VGA Application Specific Integrated Circuit Automatic Server Recovery & Restart Basic Input Output System Controller Area Network (CAN-Bus) Central Processing Unit Disk Array Controller Dual Inline Memory Module Dual Inline Package Direct Memory Access Environment Control Unit Enhanced Data Output Dynamic Random Access Memory Fast Page Mode Intelligent Input Output Integrated Drive Electronics Industry Standard Architecture In-System Programmable Local Area Network Liquid Crystal Display Light-Emitting Diode Low Voltage Differential Multiprocessor Interrupt (Controller) On-Line Replaceable PCI/ISA Bridge and IDE Accelerator Peripheral Component Interconnect Programmed Input Output PCI Expander Bridge Real Time Clock Remote Test and Diagnostic System (RemoteView) SCSI Accessed Fault-Tolerant Enclosure Single Connected Attachment Small Computer System Interface Single Ended SAF-TE Terminator Module Universal Serial Bus Video Graphics Array 2 - English U41029-J-Z

3 Abbreviations Important notes Important notes Store this manual close to the device. If you pass on the device to third parties, you should also pass on this manual.! Be sure to read this page carefully and note the information before you open the Server. Please note the information provided in the chapter "Safety" in the Operating Manual of the server. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the chapter "I/O board" - "Replacing the lithium battery". The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the trashcan. It must be disposed of in accordance with local regulations concerning special waste. Connecting cables for peripherals must be adequately insulated to avoid interference. Components can become very hot during operation. Make sure you do not touch components when making extensions to the boards. There is a danger of burns!! i The warranty expires if the device is damaged during the installation or replacement of system expansions. Information on which system expansions you can use is available from your sales office or the customer service. Boards with electrostatic sensitive devices (ESD) may be identified by labels. When you handle boards fitted with ESDs, you must observe the following points under all circumstances: You must always discharge yourself (e.g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges. Pull out the power plug before inserting or pulling out boards containing ESDs. Always hold boards with ESDs by their edges. Never touch pins or conductors on boards fitted with ESDs. U41029-J-Z English - 3

4 I/O board Abbreviations I/O board Features Intel Chipset 82450NX 512 Kbytes Flash BIOS Intel i960 processor for PCI-to-PCI-Bridge, I 2 O and Server Management Intel CAN controller Intel Fast Ethernet LAN controller two Symbios 53C875 Ultra Wide SCSI controller Cirrus CL-GD5446 graphics controller with 2 Mbyte video memory IDE hard disk controller connected to PCI bus for up to two IDE drives ultra DMA33 mode capable, supports PIO modes 0-4 Real-time clock/calendar with integrated battery backup Floppy disk controller (up to 2.88 Mbytes format) four 64 bit hot-plug PCI slots four 32 bit hot-plug PCI slots two 32 bit PCI slots (one slot shared) four ISA slots (three slots shared) two 32-bit PCI slots over i960 processor (both shared) PS/2 mouse port PS/2 keyboard port four external serial ports USB (Universal Serial Bus) CAN bus LAN port Cover detection Remote On possible via modem, via internal fax modem and via the four external serial ports Wake On LAN 4 - English U41029-J-Z

5 Interfaces and connectors I/O board Interfaces and connectors = SCSI 1 16 bit 2 = SCSI 2 16 bit 3 = Cover detection 4 = ECU 5 = ISP 6 = Floppy disk drive 7 = IDE power supply 8 = IDE drives 9 = Hot-plug PCI panel for 64 bit slots 10 = Hot-plug PCI panel for 32 bit slots 11 = Keyboard and mouse 12 = USB 13 = LAN 14 = Remote On (Fax modem / Internal Modem On) 15 = Wake up on LAN U41029-J-Z English - 5

6 I/O board Possible screen resolution Possible screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the I/O board. If you are using an external screen controller, you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller. Screen resolution Refresh rate (Hz) Horizontalrate Max. number of colors (khz) ** 640x , x x , x , x , x , x , x x x x x x x x , x , x x x interlaced x interlaced x , x , x x x ,7 256 * 1024x * 1280x interlaced x interlaced x ,7 256 * 1280x ,4 256 * * no 16 color mode ** The horizontal rate values may have a tolerance range of ± 0.3 khz. 6 - English U41029-J-Z

7 Settings with the switch block I/O board Settings with the switch block OFF ON Switch 1 to 5 = not used Switch 6 = Write protection for floppy disks Switch 7 = Skipping password query Switch 8 = Recovering system BIOS U41029-J-Z English - 7

8 I/O board Settings with the switch block Write protection for floppy disks - switch 6 Switch 6 is used to define whether floppy disks can be written or deleted in the floppy disk drive. To write and delete floppy disks, the write -protection in BIOS setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled). on The floppy disk drive is write-protected. off Read, write and delete floppy disks is possible (default setting). Skipping the password query - switch 7 Switch 7 is used to define whether the password is queried at system startup, if the password protection is enabled in BIOS Setup (in Security menu, the Password field must be set to Enabled). on The password query is effective. off The password query is skipped (default setting). Recovering System BIOS - switch 8 Switch 8 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service). on The system boots from the "Flash BIOS floppy disk" from Drive A and reprograms the system BIOS on the I/O board. off The system is started with the system BIOS on the I/O board. The system BIOS cannot be reprogrammed. (Default setting) 8 - English U41029-J-Z

9 Add-on modules I/O board Add-on modules = Battery 2 = Slots for i960 memory (odd) 3 = Slots for i960 memory (even) 4 = Flash BIOS 5 = Interface board 6 = ISA slots 7 = 32 bit PCI slots (bus 1-i960) 8 = 32 bit PCI slots (bus 0-0A) 9 = 32 bit Hot-plug PCI slots (bus 2-0B) 10 = 64 bit Hot-plug PCI slots (bus 3-1A) All PCI slots have bus master capability. U41029-J-Z English - 9

10 I/O board Add-on modules Memory extension for i960 The I/O board is equipped with two installation banks (even and odd) for memory modules. Both memory banks can be equipped with single-sided or double-sided memory modules. Equipping must begin with the even installation bank. The board supports a maximum of 16 Mbytes. Only the combination possibilities listed in the following table are permitted. Even Bank Odd Bank Maximum memory configuration 4 Mbyte single-sided no memory module 4 Mbyte 4 Mbyte single-sided 4 Mbyte single-sided 8 Mbyte 8 Mbyte double-sided 8 Mbyte double-sided 16 Mbyte Equipping sequence/slot priority Equip the slots according to the following table. Go through the table from top to bottom. The priority decreases from top to bottom. Board Slot PCI screen controller* PCI DAC (one) bit PCI controller PCI DAC (several) ISA controller bit PCI controller (other) *: The PCI screen controller must be inserted in either slot 9 or slot English U41029-J-Z

11 Add-on modules I/O board ISA bus resources Device IRQ Address DMA Keyboard 1 Serial port COM F8, 02F8, 03E8, 02E8 Serial interface COM1 4 03F8, 02F8, 03E8, 02E8 5 Floppy disk drive controller 6 2 Parallel interface LPT , 0378, 03BC 0, 1, 3 Real-time clock (RTC) 8 free 9, 10, 11 Mouse controller 12 Numeric processor 13 IDE controller 14 1F0-1F7 free 15 Serial port COM 3 possible: 15, 12, 11, 10, 9, 7, 6, 5, 4 (shared with COM1), 3 Serial port COM 4 possible: 15, 12, 11, 10, 9, 7, 6, 5, 4, 3 (shared with COM2) "IRQ" = interrupt assigned as shipped "Address" = this address can be used for your particular device "Address" = this DMA can be used for your particular device Default settings are shown in bold print. 03F8, 02F8, 03E8, 02E8 03F8, 02F8, 03E8, 02E8 U41029-J-Z English - 11

12 I/O board Add-on modules PCI bus resources PCI slots The following table shows an overview of the PCI slots: PCI Label PCI PCI bus name 64bit/ Hot Shared Description slot # Bus # 32bit Plug 1 X100 3 PCI-Bus 3-1A 64 bit yes no 64 bit hot-plug PCI bus slot 2 X101 3 PCI-Bus 3-1A 64 bit yes no 64 bit hot-plug PCI bus slot 3 X102 3 PCI-Bus 3-1A 64 bit yes no 64 bit hot-plug PCI bus slot 4 X103 3 PCI-Bus 3-1A 64 bit yes no 64 bit hot-plug PCI bus slot 5 X200 2 PCI-Bus 2-0B 32 bit yes no 32 bit hot-plug PCI bus slot 6 X201 2 PCI-Bus 2-0B 32 bit yes no 32 bit hot-plug PCI bus slot 7 X202 2 PCI-Bus 2-0B 32 bit yes no 32 bit hot-plug PCI bus slot 8 X203 2 PCI-Bus 2-0B 32 bit yes no 32 bit hot-plug PCI bus slot 9 X300 0 PCI-Bus 0-0A 32 bit no no 32 bit PCI bus slot 10 X301 0 PCI-Bus 0-0A 32 bit no yes 32 bit PCI bus slot 11 X400 1 PCI-Bus 1-i bit no yes 32 bit PCI bus slot 12 X401 1 PCI-Bus 1-i bit no yes 32 bit PCI bus slot PCI bus names The I/O board is equipped with four physical PCI buses. PCI bus name PCI-Bus 0-0A PCI-Bus 2-0B PCI-Bus 1-i960 PCI-Bus 3-1A 32 bit PCI bus 32 bit hot-plug PCI bus 32 bit PCI bus 64 bit hot-plug PCI bus Description 12 - English U41029-J-Z

13 Add-on modules I/O board PCI device numbers The following table shows the device numbers assigned to the PCI devices and PCI slots on the I/O board: PCI bus number PCI bus Device number PCI-AD Device 0 PCI-Bus 0-0A 2 AD18 PIIX4 0 PCI-Bus 0-0A 3 AD19 VGA 0 PCI-Bus 0-0A 4 AD20 MINT-ASIC 0 PCI-Bus 0-0A 5 AD21 I960RD, I2O controller and PCI-to-PCI bridge 0 PCI-Bus 0-0A 12 AD28 PCI Slot 9, X300 0 PCI-Bus 0-0A 13 AD29 PCI Slot 10, X301 0 PCI-Bus 0-0A 16 (10h) - MIOC 0 PCI-Bus 0-0A 17 (11h) - reserved 0 PCI-Bus 0-0A 18 (12h) - PXB 0, PCI Bus 0A 0 PCI-Bus 0-0A 19 (13h) - PXB 0, PCI Bus 0B 0 PCI-Bus 0-0A 20 (14h) - PXB 1, PCI Bus 1A 0 PCI-Bus 0-0A 21 (15h) - not used, PCI Bus 1A is 64 bit in width 1 PCI-Bus 1-i960 1 AD17 Ethernet controller 1 PCI-Bus 1-i960 2 AD18 SCSI controller 1 1 PCI-Bus 1-i960 3 AD19 SCSI controller 2 1 PCI-Bus 1-i960 4 AD20 PCI slot 11, X400 1 PCI-Bus 1-i960 5 AD21 PCI slot 11, X401 2 PCI-Bus 2-0B 12 AD28 PCI slot 5, X200 2 PCI-Bus 2-0B 13 AD29 PCI slot 6, X201 2 PCI-Bus 2-0B 14 AD30 PCI slot 7, X202 2 PCI-Bus 2-0B 15 AD31 PCI slot 8, X203 3 PCI-Bus 3-1A 12 AD28 PCI slot 1, X100 3 PCI-Bus 3-1A 13 AD29 PCI slot 2, X101 3 PCI-Bus 3-1A 14 AD30 PCI slot 3, X102 3 PCI-Bus 3-1A 15 AD31 PCI slot 4, X103 U41029-J-Z English - 13

14 I/O board Add-on modules PCI bus slots and PCI bus devices The following table shows the assignment of the four different PCI buses to the PCI slots and PCI devices. PCI bus name PCI bus number Slot/Devic e PCI slot 64 bit/ 32 bit Hotplug Shared Description PCI-Bus 0-0A 0 X bit no no 32 bit PCI bus slot 1 PCI-Bus 0-0A 0 X bit no yes 32 bit PCI bus slot 2 PCI-Bus 0-0A 0 CL- GD bit - - VGA controller PCI-Bus 0-0A 0 MINT - 32 bit - - Multiprocessor Interrupt Router and I/O APIC PCI-Bus 0-0A 0 I960RD - 32 bit - - I 2 O controller and PCI-to-PCI bridge PCI-Bus 1-i960 1 X bit no yes 32 bit I 2 O PCI bus slot 1 PCI-Bus 1-i960 1 X bit no yes 32 bit I 2 O PCI bus slot PCI-Bus 1-i C875J - 32 bit - - SCSI controller 1 PCI-Bus 1-i C875J - 32 bit - - SCSI controller 2 PCI-Bus 1-i C bit /100Mbit Ethernet controller PCI-Bus 2-0B 2 X bit yes no 32 bit hot-plug PCI bus slot 1 PCI-Bus 2-0B 2 X bit yes no 32 bit hot-plug PCI bus slot 2 PCI-Bus 2-0B 2 X bit yes no 32 bit hot-plug PCI bus slot 3 PCI-Bus 2-0B 2 X bit yes no 32 bit hot-plug PCI bus slot 4 PCI-Bus 3-1A 3 X bit yes no 64 bit hot-plug PCI bus slot 1 PCI-Bus 3-1A 3 X bit yes no 64 bit hot-plug PCI bus slot 2 PCI-Bus 3-1A 3 X bit yes no 64 bit hot-plug PCI bus slot 3 PCI-Bus 3-1A 3 X bit yes no 64 bit hot-plug PCI bus slot English U41029-J-Z

15 Add-on modules I/O board Interrupt Request Levels The following applies to all four PCI buses: All INTA# PCI interrupts of a PCI bus are carried on various PCI bus interrupts of the PCI interrupt controller (MINT-ASIC or MINT-ASIC plus PIIX4 for PCI bus 0A). This prevents PC boards in different slots of the same PCI bus from using the same PCI interrupt. The VGA controller, the MINT-ASIC, the I960 I 2 O controller and the PCI-to-PCI bridge do not use PCI interrupts. The following tables show the interrupt assignment of the four PCI buses. PCI-Bus 0-0A The PCI bus interrupts of the compatible 32 bit PCI bus, PCI bus 1-0A, are carried on both the PIIX4 Southbridge and on the MINT-ASIC. PIIX4 PCI bus interrupt Slot 9 Bus 0-0A Slot 1 Connector X300 Slot 10 Bus 0-0A Slot 2 Connector X301 PCI-INTA# INTA# INTB# PCI-INTB# INTB# INTC# PCI-INTC# INTC# INTD# PCI-INTD# INTD# INTA# MINT PCI bus interrupt Slot 9 Bus 0-0A Slot 1 Connector X300 Slot 10 Bus 0-0A Slot 2 Connector X301 MINT-PCI-INT0# INTA# INTB# MINT-PCI-INT1# INTB# INTC# MINT-PCI-INT2# INTC# INTD# MINT-PCI-INT3# INTD# INTA# PCI-Bus 2-0B The PCI bus interrupts of the 32 bit hot-plug PCI bus, PCI bus 2-0B, are only carried on the MINT- ASIC. MINT PCI bus interrupt Slot 5 Bus 2-0B Slot 1 Connector X200 Slot 6 Bus 2-0B Slot 2 Connector X201 Slot 7 Bus 2-0B Slot 3 Connector X202 Slot 8 Bus 2-0B Slot 4 Connector X203 MINT-PCI-INT4# INTA# INTB# INTC# INTD# MINT-PCI-INT5# INTB# INTC# INTD# INTA# MINT-PCI-INT6# INTC# INTD# INTA# INTB# MINT-PCI-INT7# INTD# INTA# INTB# INTC# U41029-J-Z English - 15

16 I/O board Add-on modules PCI-Bus 3-1A The PCI bus interrupts of the 64 bit hot-plug PCI bus, PCI bus 3-1A, are only carried on the MINT- ASIC. MINT PCI bus interrupt Slot 1 Bus 3-1A Slot 1 Connector X100 Slot 2 Bus 3-1A Slot 2 Connector X101 Slot 3 Bus 3-1A Slot 3 Connector X102 Slot 4 Bus 3-1A Slot 4 Connector X103 MINT-PCI-INT8# INTA# INTB# INTC# INTD# MINT-PCI-INT9# INTB# INTC# INTD# INTA# MINT-PCI-INT10# INTC# INTD# INTA# INTB# MINT-PCI-INT11# INTD# INTA# INTB# INTC# PCI-Bus 1-i960 The PCI bus interrupts of the 32 bit PCI bus are only carried on the MINT-ASIC. MINT PCI bus interrupt Slot 11 Bus 1-i960 Slot 1 Connector X400 Slot 12 Bus 2-i960 Slot 1 Connector X401 Ethernet Controller Intel SCSI Controller 1 SYM 53C875J SCSI Controller 2 SYM 53C875J MINT-PCI-INT12# INTA# INTB# MINT-PCI-INT13# INTB# INTC# INTB# MINT-PCI-INT14# INTC# INTD# INTC# MINT-PCI-INT15# INTD# INTA# INTD# 16 - English U41029-J-Z

17 Add-on modules I/O board Replacing the lithium battery! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the trashcan. It must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. The plus pole must be on the top! ² Lift the contact (1) a few millimeters and remove the battery from its socket (2). ² Insert a new lithium battery of the same type in the socket (3). U41029-J-Z English - 17

18 Processor board Add-on modules Processor board The CPU modules and the memory boards are plugged onto the processor board LED 8 LED = Power supply 2 = Voltage regulator 3 = Memory board 1 4 = Memory board 0 5 = I 2 C bus 6 = Indicators (LED) 7 = CPU 3 8 = CPU 2 9 = CPU 1 10 = CPU English U41029-J-Z

19 Add-on modules Memory boards Memory boards The memory board is equipped with 16 slots for memory modules. The organization in four memory banks A to D enables fast memory access with four-fold interleave. The maximum memory configuration is 4 Gbytes per memory board. 3D 2D 3C 2C 3B 2B 3A 2A 3D 2D 3C 2C 3B 2B 3A 2A 1D 0D 1C 0C 1B 0B 1A 0A 1D 0D 1C 0C 1B 0B 1A 0A Four identical memory modules must be installed per memory bank. Partial equipping of a memory bank is not possible. The equipping sequence of the memory banks is arbitrary. Each slot has a clear address (e.g. 2B): Here the letter specifies the memory bank to which the slot belongs, and the number specifies the slot number within the memory bank. 2B therefore designates slot 2 in memory bank B. The memory modules must meet the following specifications: Socket: DIMM Memory type: EDO-DRAM Voltage: 3.3 V Speed: 50 ns or 60 ns Refresh mode: 2k, 4k or 8k Memory organization: 4Mx72, 8Mx72, 16Mx72 or 32Mx72 Memory size: 32 Mbyte, 64 Mbyte, 128 Mbyte or 256 Mbyte Memory technology: 16 Mbit or 64 Mbit Installing memory modules ² Flip the holders on each side of the relevant location outwards. ² Insert the memory module in the slot while folding the side holders up until the memory module engages. Removing a memory module ² Flip the holders to the right and left of the location outwards. ² Pull the memory module out of its location. U41029-J-Z English - 19

20 Power supply board Add-on modules Power supply board The power supply board makes the connection between the power supply modules and the other system components = Control panel 2 = Power supply for hard disk drives 3 = Accessible drives 4 = System fan 5 = Drive fan 6 = Power supply for hard disk drives 7 = SCSI input 8 = Accessible drives 9 = STM 10 = Power supply for hard disk drives 11 = Safety switch 12 = Cover - power supply 13 = Power supply unit - Power supply 1 14 = Power supply unit - Power supply 2 15 = Power supply unit - Power supply 3 16 = Power supply unit - Power supply 4 17 = Power supply unit - Power supply 5 18 = Floppy disk drive 19 = Fan error indicators (LEDs) 20 = Safety switch 21 = I/O board 22 = Break-in detection switch 20 - English U41029-J-Z

21 Add-on modules Interface board Interface board The interface board makes several of the external standard interfaces available. It is installed in a special slot on the I/O board = Monitor (VGA) 2 = Parallel port (LPT) 3 = Serial port (COM 4) 4 = CAN bus 5 = Serial port (COM 3) 6 = Serial port (COM 2) 7 = Serial port (COM 1) 8 = Serial port (COM 4) 9 = CAN bus 10 = Serial port (COM 3) U41029-J-Z English - 21

22 SCSI board Add-on modules SCSI board The SCSI board connects a group of four SCSI hard disk drives to the SCSI bus SCSI ID SCSI ID 2 8 SCSI ID 1 6 SCSI ID 0 1 = Remote power-on jumper (opt.) 2 = Power supply 3 = OLR control / SAFTE board 4 = SCSI output / SAF-TE board Drive indicators 5 = Test connection 6 = SCSI input 7 = Drive indicators 8 = SCA connections for hard disk drives Each hard disk drive is assigned two drive indicators. The upper indicator (green) shows the drive activity. The lower indicator (orange) shows a hard disk error. However, a hard disk error can only be indicated when the drive is operated on a DAC English U41029-J-Z

23 STM-SE SAF-TE/Terminator board SAF-TE/Terminator board The SAF-TE/terminator board (STM) is installed on the plug SCSI output and OLR controller on the SCSI board (piggy back). The SAF-TE/terminator board terminates the SCSI bus and runs the SAF-TE protocol including OLR. The SAF-TE/terminator board is available in a single-ended (SE) and in a low-voltage differential (LVD) version. STM-SE 1 2 X2 X1 PLD SCSI Terminator GEM 200 SCSI Terminator 3 X off = OLR control to SCSI board 2 = SCSI bus to SCSI board 3 = SAF-TE controller 4 = ID-DIP switch 5 = ISP U41029-J-Z English - 23

24 SAF-TE/Terminator board STM-LVD STM-LVD = OLR control to SCSI board 2 = SCSI bus to SCSI board 3 = Housing diagnosis connection = OLR control to SCSI board 5 = Standard code jumper 6 = ISP 24 - English U41029-J-Z

25 STM-LVD ECU board ECU board The ECU board is located in the control panel slide-in module = Chipcard reader 2 = Control panel 3 = Floppy disk drive 4 = Power supply for floppy disk drive U41029-J-Z English - 25

26 Drive board 8 bit SCSI Drive board The drive board makes the connection between the drives and the SCSI system in the drive slide-in module for accessible drives. The drive board is available in an 8-bit wide and a 16-bit wide SCSI version. 8 bit SCSI = Power supply for accessible drives 2 = SCSI connection for accessible drive 3 = SCSI connection for accessible drive 4 = SCSI connection for SV board 26 - English U41029-J-Z

27 16 bit SCSI Drive board 16 bit SCSI = Power supply for accessible drives 2 = SCSI connection for accessible drive 3 = SCSI connection for SV board U41029-J-Z English - 27

28 Index 1 16 bit SCSI bit SCSI 26 A ASIC 2 ASR&R 2 B Battery 3 Battery, replacing 17 BIOS 2 C CAN 2, 4 controller 4 CAN bus 21 Chipcard reader 25 Chipset 4 COM 21 Control panel 25 CPU 2, 18 D DAC 2, 22 Device ID 5 DIMM 2, 19 DIP 2 DMA 2 Drive board bit SCSI 27 8 bit SCSI 26 Drive LEDs 22 E ECU 2, 5 ECU board 25 EDO DRAM 2, 19 Equipping sequence, slots 10 ESD 3 Ethernet LAN controller 4 F Features 1 I/O board 4 Flash BIOS 4 U41029-J-Z English - 28

29 Index Floppy disk drive 5 controller 4 FPM 2 G Graphics controller 4, 6 H Hot-plug PCI panel 5 Hot-plug PCI slots 4 Housing detection 4 Housing diagnosis connection 24 I I/O board 4 I2O 2 I2O controller 15 i960 memory extension 10 processor 4 ID-DIP switch 23 IDE 2 IDE drives 5 IDE hard disk controller 4 IDE power supply 5 Important notes 3 Installing, memory module 19 Interface board 21 Interrupt assignment 15 ISA 2 ISA bus resources 11 ISP 2, 5, 23, 24 K Keyboard 5 L LAN 2, 4, 5 LAN Controller 4 LCD 2 LED 2 Lithium battery 3, 17 LPT 21 LVD 2, 23 M Memory board 18, 19 Memory module installing 19 removing 19 Memory, expansion 10 MINT 2 MINT-ASIC 15 U41029-J-Z English - 29

30 Index Monitor 21 Mouse 5 N Notational conventions 1 O OLR 2, 22, 24 OLR control 23 P Parallel interface 21 Password query, skipping 8 PCI 2 PCI bus A 15 1-i B A 16 devices 14 names 12 resources 12 slots 14 PCI device numbers 13 PCI slots 4, 12 PCI-to-PCI bridge 15 PIIX4 2 PIO 2 Power supply 18 Power supply board 20 Priority, slot 10 Processor board 18 PS/2 keyboard port 4 PS/2 mouse port 4 PXB 2 R Real-time clock 4 Remote On 4, 5 Removing, memory module 19 Resources ISA bus 11 PCI bus 12 RTC 2 RTDS 2 S SAF-TE 2 SAF-TE controller 23 SAF-TE/Terminator board 23 SCA 2, 22 Screen resolutions 6 SCSI English U41029-J-Z

31 Index SCSI 1 16 bit 5 SCSI 2 16 bit 5 SCSI board 22 SCSI controller 4 SE 2, 23 Serial interface 4, 21 Slot priority 10 Slots 4 Specification, memory modules 19 STM 2 STM-LVD 24 STM-SE 23 System BIOS recovering 8 System fan 20 U USB 2, 4, 5 V VGA 2, 21 VGA controller 15 Voltage regulator 18 W Wake on LAN 4 Wake up on LAN 5 Write-protection for floppy disks 8 U41029-J-Z English - 31

32

33 Contents Introduction...1 Notational conventions...1 Overview...1 Abbreviations...2 Important notes...3 I/O board...4 Interfaces and connectors...5 Possible screen resolution...6 Settings with the switch block...7 Add-on modules...9 Memory extension for i Equipping sequence/slot priority...10 ISA bus resources...11 PCI bus resources...12 Replacing the lithium battery...17 Processor board...18 Memory boards...19 Power supply board...20 Interface board...21 SCSI board...22 SAF-TE/Terminator board...23 STM-SE...23 STM-LVD...24 ECU board...25 Drive board bit SCSI bit SCSI...27 Index...28 U41029-J-Z

34 U41029-J-Z PRIMERGY 870 System Boards Technical Manual August 1998 edition IIntel is a registered trademark of Intel Corporation, USA. PS/2 is a registered trademark of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. Copyright Siemens AG 1998 All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability. Right of technical modification reserved. U41029-J-Z

35 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed. Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions. Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the The Internet pages of Fujitsu Technology Solutions are available at and the user documentation at Copyright Fujitsu Technology Solutions, 2009 Hinweise zum vorliegenden Dokument Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions. Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion. Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind. Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Die Internetseiten von Fujitsu Technology Solutions finden Sie unter und unter finden Sie die Benutzerdokumentation. Copyright Fujitsu Technology Solutions, 2009