FIBARO SWIPE OPERATING MANUAL FGGC-001 CONTENTS

Transcription

1 OPERATING MANUAL EN FIBARO FIBARO SWIPE FGGC-001 CONTENTS #1: Descrpton and features 4 #2: Gestures overvew 5 #3: Basc actvaton 6 #4: Addng the devce 8 #5: Removng the devce 9 #6: Operatng the devce 10 #7: Scene ID 11 v1.0 #8: Sequences of gestures 12 #9: Powerng modes 14 #10: Addtonal features 15 #11: Assocatons 16 #12: Advanced parameters 17 #13: Specfcatons 23 #14: Regulatons 24

2 3 Important safety nformaton! Read ths manual before attemptng to nstall the devce! Falure to observe recommendatons ncluded n ths manual may be dangerous or cause a volaton of the law. The manufacturer, Fbar Group S.A. wll not be held responsble for any loss or damage resultng from not followng the nstructons of operatng manual. General nformaton about the FIBARO System FIBARO s a wreless smart home automaton system, based on the Z-Wave protocol. All of avalable devces can be controlled through a computer (PC or Mac), smartphone or tablet. Z-Wave devces (nonbattery powered) are not only recevers, but can also repeat the sgnal, ncreasng the Z-Wave network s range. It gves advantage over tradtonal wreless systems that requre drect lnk between transmtter and recever, as a result the constructon of the buldng could affect network s range negatvely. Every FIBARO network has ts unque dentfcaton number (home ID). Multple ndependent networks can exst n the buldng wthout nterferng. Transmsson securty of FIBARO System s comparable to wred systems. Z-Wave technology s the leadng soluton n smart home automaton. There s a wde range of Z-Wave devces that are mutually compatble, ndependently of manufacturer. It gves the system the ablty to evolve and expand over tme. For more nformaton vst:

3 4 5 #1: Descrpton and features #2: Gestures overvew FIBARO Swpe s a revolutonary battery gesture control pad that allows you to control devces n your Z-Wave network wthout actually touchng anythng. Swpe up, down, left, rght, make a crcular gesture and use sequences to get full and ntutve control of your home. Installed devce perfectly matches your nteror desgn, as t resembles a pcture frame. You can even personalze t wth your favourte pcture. Gesture controlled menu allow to add/remove or reset the devce wthout dsmountng t. The devce s equpped wth a buzzer that confrms performed gestures and other actons. Basc gestures are used to turn ON and OFF assocated devces or trgger scenes. Swpe up Swpe down Ths devce may be used wth all devces certfed wth the Z-Wave Plus certfcate and should be compatble wth such devces produced by other manufacturers. FIBARO Swpe s a Securty Enabled Z-Wave Plus product and a Securty Enabled Z-Wave Controller must be used n order to fully utlze the product. Man features of FIBARO Swpe: Compatble wth any Z-Wave or Z-Wave+ Controller. Supports protected mode (Z-Wave network securty mode) wth AES-128 encrypton. Allows contactless gesture detecton. Battery and/or VDC powered. When connected to an external, VDC power source, the battery serves as an emergency power source. Gestures and actons are confrmed by the buzzer and can be ndcated addtonally by the bult-n LED dode. Gesture controlled menu - allows to operate the devce wthout dsmountng t. FIBARO Swpe s a fully compatble Z-Wave PLUS devce. Swpe left Swpe rght Crcular gestures are used to e.g. dm/brghten the lghts or adjust the blnds va assocatons. They can also trgger scenes. After performng frst crcle, the devce wll start changng the value (clockwse - ncrease, counter-clockwse - decrease). Wthdrawng the hand wll stop the change. Clockwse Counter clockwse Sequences are composed of two or three gestures. User can create up to 6 custom sequences. They can operate other devces va scenes only. Sequence Descrpton and features Gestures overvew

4 6 7 #3: Basc actvaton 9. Plug the power source nto the mcro-usb port f requred. 1. Remove the front magnetc cover. 10. Set the man controller n (securty/non-securty) add mode (see the controller s manual). 11. Move and hold your hand close to the center of the pad. 2. Unmount the Swpe from the back case by sldng the devce down. 3. Remove paper strp protectng the batteres. 12. If the devce s battery powered, hgh ptched beep wll sgnal extng the Standby Mode. 13. Loud sound sequence wll confrm enterng the menu, keep holdng your hand. 14. After hearng two short beeps (green ndcator colour), wthdraw the hand and perform swpng up gesture to confrm selecton (two beeps wll confrm valdty). 4. Mount the Swpe back nto the back case by sldng the devce up. 5. The devce wll confrm powerng up wth an acoustc sgnal. 6. Place the front magnetc cover. 15. Wat for the addng process to end. 16. Successful addng wll be confrmed by the Z-Wave controller s message and 3 short beeps (green vsual ndcator colour). 7. Place the Swpe onto ts holder. 8. Place the Swpe wthn the drect range of your Z-Wave controller. Basc actvaton Basc actvaton

5 8 9 #4: Addng the devce #5: Removng the devce Addng n securty mode must be performed up to 2 meters from the controller. In case the devce s not added, please reset the devce and repeat the addng procedure. Addng (Incluson) - Z-Wave devce learnng mode, allowng to add the devce to exstng Z-Wave network. To add the devce to the Z-Wave network: 1. Place the Swpe wthn the drect range of your Z-Wave controller. 2. Set the man controller n (securty/non-securty) add mode (see the controller s manual). 3. Move and hold your hand close to the center of the pad. Removng (Excluson) - Z-Wave devce learnng mode, allowng to remove the devce from exstng Z-Wave network. To remove the devce to the Z-Wave network: 1. Place the Swpe wthn the drect range of your Z-Wave controller. 2. Set the man controller n remove mode (see the controller s manual). 3. Move and hold your hand close to the center of the pad. Removng the Swpe from the Z-Wave network restores all the default parameters of the devce. 4. If the devce s battery powered, hgh ptched beep wll sgnal extng the Standby Mode. 5. Loud sound sequence wll confrm enterng the menu, keep holdng your hand. 6. After hearng two short beeps (green ndcator colour), wthdraw the hand and perform swpng up gesture to confrm selecton (two beeps wll confrm valdty). 4. If the devce s battery powered, hgh ptched beep wll sgnal extng the Standby Mode. 5. Loud sound sequence wll confrm enterng the menu, keep holdng your hand. 6. After hearng two short beeps (green ndcator colour), wthdraw the hand and perform swpng up gesture to confrm selecton (two beeps wll confrm valdty). If the devce s battery powered, hgh ptched beep wll sgnalze extng from the Standby Mode before enterng the menu. 7. Wat for the addng process to end. 7. Wat for the removng process to end. 8. Successful addng wll be confrmed by the Z-Wave controller s message and 3 short beeps (green vsual ndcator colour). 8. Successful removng wll be confrmed by the Z-Wave controller s message and sequence of 2 short beeps, pause, 1 short beep (red vsual ndcator colour). Addng the devce Removng the devce

6 10 11 #6: Operatng the devce #7: Scene ID Gestures are not ndcated by the LED dode by default. In order to enable t, set the value of parameter 3 to 1. If the devce s battery powered, hgh ptch beep wll sgnalze extng from the Standby Mode before enterng the menu. Menu can also be operated usng the servce button B (see "Addtonal features" on page 15). Resettng the devce s not the recommended way of removng the devce from the Z-Wave network. Use the reset procedure only f the prmary controller s mssng or noperable. Certan devce removal can be acheved by the procedure of removng descrbed n "Addng the devce" on page 8. Acoustc and vsual ndcatons: The Swpe s equpped wth a buzzer and LED dode, sgnallng gesture detecton, menu poston and status of the devce. Valdty of every detected gesture or sequence s sgnalled by: 2 short beeps (GREEN) - gesture/sequence s vald Intermttent tone (GREEN) - smooth control usng crcular gesture 1 long beep (RED) - gesture/sequence s nvald Menu allows to perform Z-Wave network actons. In order to use the menu: 1. Move and hold your hand close to the center of the pad. 2. Loud sound sequence wll confrm enterng the menu, keep holdng your hand. 3. Wat for the buzzer to ndcate the desred menu poston: 1 short beep (WHITE ndcator colour) - wake up the devce 2 short beeps (GREEN ndcator colour) - learnng mode (addng/removng) 3 short beeps (YELLOW ndcator colour) - the devce reset 4. To select current poston, wthdraw the hand and perform swpng up gesture to confrm selecton (two beeps wll confrm valdty). Wakng up the devce: The Swpe needs to be woken up to receve nformaton about the new confguraton from the Z-Wave controller, lke parameters and assocatons. Use 1st menu poston to wake up the devce or clck the button on the back of the devce once. Reset procedure of the Swpe: Reset procedure allows to restore the devce back to ts factory settngs, whch means all nformaton about the Z-Wave controller and user confguraton wll be deleted. In order to reset the devce: 1. Make sure the devce s powered. 2. Choose 3rd menu poston (3 short beeps). 3. After few seconds the devce wll be restarted. Not beng added to the Z-Wave network wll be sgnalzed wth sequence of 2 short beeps, pause, 1 short beep (RED). Scene ID: Every basc gesture and sequence has ts own Scene ID that s send to the man controller after recognzng t. Scene actvaton for basc gestures s send after second gesture or tmeout. Scene ID Gesture or sequence Attrbute Default acton /\ Key Pressed 1 tme ON /\ /\ Key Pressed 2 tmes OFF \/ Key Pressed 1 tme ON \/ \/ Key Pressed 2 tmes OFF < Key Pressed 1 tme ON < < Key Pressed 2 tmes OFF > Key Pressed 1 tme ON > > Key Pressed 2 tmes OFF Crcular gesture (clockwse) Crcular gesture (counter-clockwse) Key Held Down Key Released Key Held Down Key Released Change state UP STOP Change state DOWN STOP 7 1st sequence Key Pressed 1 tme User-defned 8 2nd sequence Key Pressed 1 tme User-defned 9 3rd sequence Key Pressed 1 tme User-defned 10 4th sequence Key Pressed 1 tme User-defned 11 5th sequence Key Pressed 1 tme User-defned 12 6th sequence Key Pressed 1 tme User-defned Toggle Mode (parameter 12) dsallows doubled gestures. Operatng the devce Scene ID

7 12 13 #8: Sequences of gestures Creatng and confgurng sequences n the Home Center nterface: 1. Go to the devce optons by clckng the con on ts bar: 2. Drag and drop two or three gestures to create a desred sequence. Sequences: User can create sequences of two or three gestures to expand number of possble actons. Every sequence s saved n ts advanced parameter (no ) wth 16 bts, every basc gesture s dentfed wth 4 bts. 3. Confrm the selecton by clckng Confrm a new sequence. 4. Wake up the devce usng 1st menu poston (see "Operatng the devce" on page 10). 5. Clck the plus con ("New Reacton") next to the newly created sequence. 6. Select the devce you want to control. Gesture values: Value 4 bts Gesture empty /\ \/ < > In case of sequence of two gesture, feld for thrd gesture should be set to 0. Rules of creatng sequences: Bt mask of parameter Maxmum of sx sequences can be created. Overall Sze 4 bts 4 bts 4 bts 4 bts 16 bts Purpose reserved frst gesture second gesture thrd gesture Example none /\ > < Example: bnary values Example: decmal values always always 0 1 * * 16 3 * 1 sum = From the avalable optons select the reacton of the controlled devce and complete the setup by clckng "Save". Creatng and edtng sequences manually: To manually create or edt a sequence slot: 1. Calculate new value of parameter usng table and formula: Value of parameter = 256 * Value of frst gesture * Value of second gesture + Value of thrd gesture 2. Change the value of correspondng parameter (parameters 31 to 36 for slots 1 to 6). Settng parameter to 0 wll delete the sequence. Each sequence must be unque. Sequence can consst of two or three basc gestures (left, rght, up or down). Two dentcal gestures cannot be used next to each other. Learnng a new sequence: To perform automatc learnng of a sequence: 1. Change value of parameter 30 to number of sequence slot you want to fll (1 to 6). 2. Wake up the devce usng 1st menu poston (see "Operatng the devce" on page 10) 3. The devce wll enter learnng mode, whch s sgnalled by constant beepng. 4. Perform a desred sequence. Sequences of gestures Sequences of gestures

8 14 15 #9: Powerng modes #10: Addtonal features! CAUTION Usng batteres other than specfed may result n exploson. Dspose of properly, observng envronmental protecton rules. The devce does not work as a Z-Wave repeater, even when connected to the external power supply. There are two powerng modes of the Swpe. By default, powerng mode of the devce s updated automatcally (n ntervals specfed n parameter 5) after changng type of supply. The Swpe sends detected gestures to the Z-Wave network mmedately, but confguraton parameters and assocatons settngs only at wake up (n tme ntervals or manually), ndependently of the powerng mode. Battery powerng mode - by default, the Swpe s suppled wth 4 batteres ncluded wth the devce (type AA 1.5V). They are not rechargeable and should be replaced after wearng out. The devce n ths mode uses power savng functon to preserve battery lfe. External supply mode - the Swpe can be suppled wth a 5V DC power supply connected to the mcro-usb port. In ths mode batteres wll work as an emergency supply. Power savng: When battery powered, the Swpe wll enter Standby Mode by default (sgnalled wth a low ptch beep) after 5 seconds of nactvty to reduce the battery usage. In Standby Mode range and frequency of detecton are reduced preventng normal gesture detecton. Operaton of power savng mode can be modfed n parameter 6. In order to ext Standby Mode: 1. Move your hand close to the centre of the pad. 2. Wat for the hgh ptch beep. 3. Move your hand away from the pad. 4. The devce s ready to detect gestures. Servce button B: The Swpe s equpped wth a servce B-button, whch allows to use the menu. The B-button s located on back of the devce and requres dsmountng the Swpe from ts back case. In order to operate the menu usng the B-button: 1. Make sure the devce s powered va mcro-usb port. 2. Press and hold the B-button. 3. Loud sound sequence wll confrm enterng the menu, keep holdng your hand. 4. Wat for the buzzer to ndcate the desred menu poston wth short beeps: 1 short beep (WHITE) - wake up the devce 2 short beeps (GREEN) - learnng mode (addng/removng) 3 short beeps (YELLOW) - the devce reset 5. Release the B-button. 6. Clck the B-button to confrm selecton. Powerng modes Addtonal features

9 16 17 #11: Assocatons #12: Advanced parameters Assocaton ensures drect transfer of control commands between devces, s performed wthout partcpaton of the man controller and requres assocated devce to be n the drect range. By default 2nd-5th assocaton groups are set to toggle mode - sngle gesture wll reverse state of the assocaton group (turns ON when t s OFF, turns OFF when t s ON). Can be modfed va parameter 12. States of the assocaton groups are affected only by assgned gestures. Changng state of assocated devce by other means wll not update remembered state of assocaton group. Assocaton (lnkng devces) - drect control of other devces wthn the Z-Wave system network e.g. Dmmer, Relay Swtch, Roller Shutter or scene (may be controlled only through a Z-Wave controller). The Swpe provdes the assocaton of sx groups: 1st assocaton group Lfelne reports the devce status and allows for assgnng sngle devce only (man controller by default). 2nd assocaton group Flck UP s assgned to movng the hand up over the panel (sends Basc Set command frames). 3rd assocaton group Flck DOWN s assgned to movng the hand down over the panel (sends Basc Set command frames). 4th assocaton group Flck LEFT s assgned to movng the hand from the rght to the left sde of the panel (sends Basc Set command frames). 5th assocaton group Flck RIGHT s assgned to movng the hand from the left to the rght sde of the panel (sends Basc Set command frames). 6th assocaton group Crcular ArWheel s assgned to crcular move of the hand clockwse or counter-clockwse over the panel (sends Swtch Multlevel Start/Stop Level Change command frames). The Swpe n 2nd to 6th group allows to control 5 regular or multchannel devces per an assocaton group, wth the excepton of LfeLne that s reserved solely for the controller and hence only 1 node can be assgned. It s not recommended to assocate more than 10 devces n general, as the response tme to control commands depends on the number of assocated devces. In extreme cases, system response may be delayed. To add an assocaton (usng the Home Center controller): 1. Go to the devce optons by clckng the con: 2. Select the Advanced tab. 3. Specfy to whch group and what devces are to be assocated. 4. Wat for the confguraton process to end. Sendng relevant nformaton to devces added to assocated groups may take even a few mnutes. 5. Wake up the devce manually to speed up the confguraton process (1st menu poston). The Swpe allows to customze ts operaton to user s needs. The settngs are avalable n the FIBARO nterface as smple optons that may be chosen by selectng the approprate box. In order to confgure the Swpe (usng the Home Center controller): 1. Go to the devce optons by clckng the con: 2. Select the Advanced tab. Wake up nterval Avalable settngs: 0 or (n seconds, 1mn - 18h) Default settng: (every 6 hours) The Swpe wll wake up at each defned tme nterval and always try to connect wth the man controller. After successful communcaton attempt, the devce wll update confguraton parameters, assocatons and settngs and then wll go nto Z-Wave communcaton standby. After faled communcaton attempt (eg. no Z-Wave range) the devce wll go nto Z-Wave communcaton standby and retry to establsh connecton wth the man controller after the next tme nterval. Settng wake up nterval to 0 dsables sendng Wake Up notfcaton to the controller automatcally. Wake up may be stll performed manually usng 1st menu poston. Longer tme nterval means less frequent communcaton and thus a longer battery lfe 1. Devce orentaton Parameter determnes orentaton of the Swpe n relaton to ts default poston. Requred for proper gestures recognton. Avalable settngs: 0 - default orentaton rotaton 2-90 clockwse rotaton 3-90 counter-clockwse rotaton Default settng: 0 Parameter sze: 1 [byte] 2. Buzzer - acoustc sgnal settngs Acoustc sgnallng of gestures detecton. Avalable settngs: 0 - gestures detecton s not sgnalled 1 - gestures detecton s sgnalled Default settng: 1 Parameter sze: 1 [byte] Actve acoustc sgnals can be selected n parameter 4. Assocatons Advanced parameters

10 LED dode - vsual ndcator settngs Vsual ndcaton of gestures detecton. Avalable settngs: 0 - gestures detecton s not ndcated 1 - gestures detecton s ndcated Default settng: 0 Parameter sze: 1 [bytes] 10. Scenes sent to the controller Defnes whch actons result n sendng scenes to 1st Lfelne group. Avalable settngs: 1 - scenes for flck UP gesture enabled 2 - scenes for flck DOWN gesture enabled 4 - scenes for flck LEFT gesture enabled Parameter 10 values may be combned, e.g. 1+2=3 means that scenes for flck UP and DOWN are enabled. Parameter 4 s relevant only f parameter 2 s set to Buzzer - sgnallng result of gesture recognton Acoustc sgnallng of gesture recognton result (usng the bult-n buzzer). Avalable settngs: 1 - only successful recognton s sgnalled 2 - only faled recognton s sgnalled 8 - scenes for flck RIGHT gesture enabled 16 - scenes for clockwse crcular gesture enabled 32 - scenes for counter-clockwse crcular gesture enabled Default settng: 15 Parameter sze: 1 [byte]! CAUTION After dsablng the Hold gesture n parameter 7, menu can be entered by usng the B-button only! 3 - successful and faled recognton s sgnalled Default settng: 3 Parameter sze: 1 [byte] 5. Powerng mode - nterval of updatng the current mode Ths parameter determnes how often the devce checks f the USB power supply s connected and updates powerng mode f needed. Avalable settngs: 0 - powerng mode s not updated (n mnutes) - tme nterval Default settng: 4 (4 mnutes) Parameter sze: 2 [bytes] 6. Power savng mode (battery mode) Ths parameter determnes operaton of gesture detecton when battery powered. When Standby Mode s selected, hold gesture must be performed to ext power savng mode and reactvate normal gesture recognton. The devce n Standby Mode consumes the least battery lfe. When Smple Mode mode s selected, gesture recognton s always actve, but only slowly performed gestures wll be recognzed properly (hgh battery consumpton). Avalable settngs: 0 - Standby Mode 1 - Smple Mode 2 - the Swpe does not enter power savng mode Default settng: 0 Parameter sze: 1 [byte] 7. Hold gesture to enter the menu Ths parameter allows to choose f the menu can be entered usng the Hold gesture. Avalable settngs: 0 - Hold gesture to enter the menu enabled 1 - Hold gesture to enter the menu dsabled Default settng: 0 (enabled) Parameter sze: 1 [byte] 11. Assocatons n Z-Wave network securty mode Parameter defnes how commands are sent n specfed assocaton groups: as secure or non-secure. Parameter s actve only n Z-Wave network securty mode. It does not apply to 1st Lfelne assocaton group. Avalable settngs: 1-2nd group Flck UP sent as secure 2-3rd group Flck DOWN sent as secure 4-4th group Flck LEFT sent as secure 8-5th group Flck RIGHT sent as secure 16-6th group Crcular ArWheel sent as secure Default settng: 31 Parameter sze: 1 [byte] 12. Control mode of 2nd - 5th Flck UP/DOWN/LEFT/RIGHT assocaton groups and scenes Parameter allows to choose control mode for 2nd-5th groups and scenes. By default, Toggle Mode s actve, meanng that a sngle flck turns ON the group and the same flck turns t OFF, doubled flcks are nactve. After dsablng Toggle Mode a sngle flck wll turn the devce ON and the same flck doubled wll turn t OFF. Avalable settngs: 1 - Toggle Mode enabled for 2nd assocaton group 2 - Toggle Mode enabled for 3rd assocaton group 4 - Toggle Mode enabled for 4th assocaton group 8 - Toggle Mode enabled for 5th assocaton group Default settng: 15 Parameter sze: 1 [byte] Parameter 11 values may be combned, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure. Parameter 12 values may be combned, e.g. 1+2=3 means that 2nd & 3rd group are selected. Dsablng Toggle Mode wll ntroduce delay when performng sngle gestures. Assocatons Assocatons

11 20 21 Commands sent to assocaton group for turn ON/OFF can be adjusted n parameters Settng parameters to approprate value wll result n: 0 - turnng off assocated devces forcng level of assocated devces settng assocated devces to the last remembered state or turnng them on 13. Rate of smooth level control Parameter allows to choose how long the hand has to be held near the center of the pad after "ArWheel" gesture for the assocated devces to reach ther maxmum/mnmum level. Avalable settngs: duraton n seconds default settngs of controlled devces Default settng: 255 Parameter sze: 2 [bytes] ASSOCIATIONS - CONTROL FRAMES CONFIGURATION 20. SWITCH ON control frame value for FLICK UP gesture Ths parameter allows to set value sent n SWITCH ON command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 255 Parameter sze: 2 [bytes] 21. SWITCH OFF control frame value for FLICK UP gesture Ths parameter allows to set value sent n SWITCH OFF command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 0 Parameter sze: 2 [bytes] 22. SWITCH ON control frame value for FLICK DOWN gesture Ths parameter allows to set value sent n SWITCH ON command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 255 Parameter sze: 2 [bytes] 23. SWITCH OFF control frame value for FLICK DOWN gesture Ths parameter allows to set value sent n SWITCH OFF command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 0 Parameter sze: 2 [bytes] 24. SWITCH ON control frame value for FLICK LEFT gesture Ths parameter allows to set value sent n SWITCH ON command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 255 Parameter sze: 2 [bytes] 25. SWITCH OFF control frame value for FLICK LEFT gesture Ths parameter allows to set value sent n SWITCH OFF command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 0 Parameter sze: 2 [bytes] 26. SWITCH ON control frame value for FLICK RIGHT gesture Ths parameter allows to set value sent n SWITCH ON command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 255 Parameter sze: 2 [bytes] 27. SWITCH OFF control frame value for FLICK RIGHT gesture Ths parameter allows to set value sent n SWITCH OFF command frame to the assocaton group. Avalable settngs: 0-99 or 255 Default settng: 0 Parameter sze: 2 [bytes] SEQUENCES OF GESTURES 30. Sequence learnng mode Parameter actvated by the man Z-Wave controller. Change ts value to launch sequence learnng procedure for the desred slot. Avalable settngs: 0 - learnng mode dsabled launch sequence learnng for selected slot Default settng: 0 Parameter sze: 1 [byte] 31. 1st gestures sequence (SLOT 1) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] 32. 2nd gestures sequence (SLOT 2) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] Sequences does not allow to use same gestures next to each other. Parameters can also be used to manually set a sequence accordng to detals descrbed n "Sequences of gestures" on page 12. Assocatons Assocatons

12 rd gestures sequence (SLOT 3) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. #13: Specfcatons Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] 34. 4th gestures sequence (SLOT 4) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] 35. 5th gestures sequence (SLOT 5) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] 36. 6th gestures sequence (SLOT 6) Value contanng sequence of gestures. See "Sequences of gestures" on page 12 for more nformaton. Avalable settngs: Default settng: 0 Parameter sze: 2 [bytes] Power supply: Operatonal current: DC supply connector: Battery type: EU drectves complance: Rado protocol: Rado frequency: Range: Dmensons: 5V DC power supply and/or batteres < 60mA mcro-usb 4 x 1.5V AA RoHS 2011/65/EU R&TTE 1999/5/EC Z-Wave (500 seres chp) or MHz EU; or MHz US; or MHz ANZ; MHz RU; up to 50m outdoors up to 40m ndoors (Dependng on terran and buldng structure) 178 x 130 x 29 mm! CAUTION Usng batteres other than specfed may result n exploson. Dspose of properly, observng envronmental protecton rules. Rado frequency of ndvdual devce must be same as your Z-Wave controller. Check nformaton on the box or consult your dealer f you are not sure. Assocatons Specfcatons

13 24 25 #14: Regulatons Ths devce comples wth Part 15 of the FCC Rules Operaton s subject to the followng two condtons: 1. Ths devce may not cause harmful nterference 2. Ths devce must accept any nterference receved, ncludng nterference that may cause undesred operaton. Ths equpment has been tested and found to comply wth the lmts for a Class B dgtal devce, pursuant to part 15 of the FCC Rules. These lmts are desgned to provde reasonable protecton aganst harmful nterference n a resdental nstallaton. Ths equpment generates, uses and can radate rado frequency energy and, f not nstalled and used n accordance wth the nstructons, may cause harmful nterference to rado communcatons. However, there s no guarantee that nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recepton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the followng measures: Reorent or relocate the recevng antenna. Increase the separaton between the equpment and recever. Connect the equpment nto an outlet on a crcut dfferent from that to whch the recever s connected. Consult the dealer or an experenced rado/tv techncan for help. Industry Canada (IC) Complance Notce Ths devce comples wth Industry Canada lcense-exempt RSSs. Operaton s subject to the followng two condtons: (1) ths devce may not cause nterference, and (2) ths devce must accept any nterference, ncludng nterference that may cause undesred operaton of the devce. Cet apparel est conforme aux normes d exempton de lcence RSS d Industry Canada. Son fonctonnement est soums aux deux condtons suvantes : (1) cet apparel ne dot pas causer d nterférence et (2) cet apparel dot accepter toute nterférence, notamment les nterférences qu peuvent affecter son fonctonnement. Note Changes and modfcatons not expressly approved by the manufacturer or regstrant of ths equpment can vod your authorty to operate ths equpment under Federal Communcatons Commsson s rules. DGT Warnng Statement Artcle 12 Wthout permsson, any company, frm or user shall not alter the frequency, ncrease the power, or change the characterstcs and functons of the orgnal desgn of the certfed lower power frequency electrc machnery. Artcle 14 The applcaton of low power frequency electrc machneres shall not affect the navgaton safety nor nterfere a legal communcaton, f an nterference s found, the servce wll be suspended untl mprovement s made and the nterference no longer exsts. 第十二條經型式認證合格之低功率射頻電機, 非經許可, 公司 商號或使用者均不得擅自變更頻率 加大功率或變更原設計之特性及功能 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信 ; 經發現有干擾現象時, 應立即停用, 並改善至無干擾時方得繼續使用 前項合法通信, 指依電信法規定作業之無線電通信 低功率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備之干擾 Declaraton of conformty Hereby, Fbar Group S.A. declares that FIBARO Swpe s n complance wth the essental requrements and other relevant provsons of Drectve 1999/5/EC. Legal Notces All nformaton, ncludng, but not lmted to, nformaton regardng the features, functonalty, and/or other product specfcaton are subject to change wthout notce. Fbaro reserves all rghts to revse or update ts products, software, or documentaton wthout any oblgaton to notfy any ndvdual or entty. FIBARO and Fbar Group logo are trademarks of Fbar Group S.A. All other brands and product names referred to heren are trademarks of ther respectve holders. Regulatons Regulatons