VideoJet X10 SN Network Video Server. Installation and Operating Manual

Transcription

1 VdeoJet X10 SN Network Vdeo Server en Installaton and Operatng Manual

2 VdeoJet X10 SN

3 VdeoJet X10 SN Table of Contents en 3 Table of Contents 1 Preface About ths Manual Conventons n ths Manual Intended Use EU Drectves Ratng Plate 8 2 Safety Informaton Electrc Shock Hazard Installaton and Operaton Mantenance and Repar 9 3 Product Descrpton Scope of Delvery System Requrements Overvew of Functons Connectons on the Front Panel Connectons on the Rear Panel 17 4 Installaton Preparatons Mountng Connectons Power On/Power Off Setup Usng the Confguraton Manager 24 5 Confguraton Usng a Web Browser Connectng Confguraton Menu Basc Mode: Unt Access Basc Mode: Date/Tme Basc Mode: Network Basc Mode: Encoder Profle Basc Mode: Audo Basc Mode: Recordng Basc Mode: System Overvew Advanced Mode: Identfcaton Advanced Mode: Password Advanced Mode: Date/Tme Advanced Mode: Dsplay Stampng Advanced Mode: Appearance Advanced Mode: LIVEPAGE Functons Advanced Mode: Loggng Advanced Mode: Vdeo Input Advanced Mode: Pcture Settngs 45 Bosch Securty Systems Installaton and Operatng Manual DOC V

4 4 en Table of Contents VdeoJet X10 SN 5.19 Advanced Mode: Encoder Profle Advanced Mode: Audo Advanced Mode: Storage Management Advanced Mode: Remote Vdeo Devce Advanced Mode: Recordng Profles Advanced Mode: Retenton Tme Advanced Mode: Recordng Scheduler Advanced Mode: Recordng Status Advanced Mode: Alarm Connectons Advanced Mode: VCA Advanced Mode: VCA Profles Advanced Mode: VCA Scheduled Advanced Mode: VCA Event Trggered Advanced Mode: Audo Alarm Advanced Mode: Alarm E-Mal Advanced Mode: Alarm Task Edtor Advanced Mode: Alarm Inputs Advanced Mode: Relay Advanced Mode: COM Advanced Mode: Network Advanced Mode: Advanced Advanced Mode: Multcastng Advanced Mode: JPEG Postng Advanced Mode: Encrypton Advanced Mode: Mantenance Advanced Mode: Lcenses Advanced Mode: System Overvew Functon Test 87 6 Operaton Operaton wth Mcrosoft Internet Explorer The LIVEPAGE Savng Snapshots Recordng Vdeo Sequences Runnng Recordng Program The RECORDINGS Page Installng the Player Hardware Connectons Between Vdeo Servers Operaton Usng Software Decoders Mantenance and Upgrades Testng the Network Connecton Unt Reset Repars Transfer and Dsposal Appendx Troubleshootng General Malfunctons 104 DOC V Installaton and Operatng Manual Bosch Securty Systems

5 VdeoJet X10 SN Table of Contents en Malfunctons wth SCSI Connectons LEDs Processor Load Network Connecton Seral Interface Termnal Block Communcaton wth Termnal Program Copyrghts Specfcatons Unt Protocols/Standards Glossary Index 119 Bosch Securty Systems Installaton and Operatng Manual DOC V

6 6 en Table of Contents VdeoJet X10 SN DOC V Installaton and Operatng Manual Bosch Securty Systems

7 VdeoJet X10 SN Preface en 7 1 Preface 1.1 About ths Manual Ths manual s ntended for persons responsble for the nstallaton and operaton of the VdeoJet X10 SN. Internatonal, natonal and any regonal electrcal engneerng regulatons must be followed at all tmes. Relevant knowledge of network technology s requred. The manual descrbes the nstallaton and operaton of the unt. 1.2 Conventons n ths Manual In ths manual, the followng symbols and notatons are used to draw attenton to specal stuatons:! CAUTION! Ths symbol ndcates that falure to follow the safety nstructons descrbed may endanger persons and cause damage to the unt or other equpment. It s assocated wth mmedate, drect hazards. Ths symbol refers to features and ndcates tps and nformaton for easer, more convenent use of the unt. 1.3 Intended Use The VdeoJet X10 SN network vdeo server transfers vdeo, audo and control sgnals over data networks (Ethernet LAN, Internet). There are varous memory optons for recordng the mages captured by the connected camera. The unt s ntended for use wth CCTV systems. Varous functons can be trggered automatcally by ncorporatng external alarm sensors. Other applcatons are not permtted. In the event of questons concernng the use of the unt whch are not answered n ths manual, please contact your sales partner or: Bosch Securty Systems Robert-Koch-Straße Ottobrunn Germany Bosch Securty Systems Installaton and Operatng Manual DOC V

8 8 en Preface VdeoJet X10 SN 1.4 EU Drectves The VdeoJet X10 SN network vdeo server comples wth the requrements of EU Drectves 89/336 (Electromagnetc Compatblty) and 73/23, amended by 93/68 (Low Voltage Drectve). 1.5 Ratng Plate For exact dentfcaton, the model name and seral number are nscrbed on the bottom of the housng. Please make a note of ths nformaton before nstallaton, f necessary, so as to have t to hand n case of questons or when orderng spare parts. DOC V Installaton and Operatng Manual Bosch Securty Systems

9 VdeoJet X10 SN Safety Informaton en 9 2 Safety Informaton 2.1 Electrc Shock Hazard Never attempt to connect the unt to any power network other than the type for whch t s ntended. Use only power supply unts wth UL approval and a power output accordng to LPS or NEC Class 2. Never open the housng. Never open the housng of the power supply unt. If a fault occurs, dsconnect the power supply unt from the power supply and from all other unts. Install the power supply and the unt only n a dry, weather-protected locaton. If safe operaton of the unt cannot be ensured, remove t from servce and secure t to prevent unauthorzed operaton. In such cases, have the unt checked by Bosch Securty Systems. Safe operaton s no longer possble n the followng cases: f there s vsble damage to the unt or power cables, f the unt no longer operates correctly, f the unt has been exposed to ran or mosture, f foregn bodes have penetrated the unt, after long storage under adverse condtons, or after exposure to extreme stress n transt. 2.2 Installaton and Operaton The relevant electrcal engneerng regulatons and gudelnes must be compled wth at all tmes durng nstallaton. Relevant knowledge of network technology s requred to nstall the unt. Before nstallng or operatng the unt, make sure you have read and understood the documentaton for the other equpment connected to t, such as cameras. The documentaton contans mportant safety nstructons and nformaton about permtted uses. Perform only the nstallaton and operaton steps descrbed n ths manual. Any other actons may lead to personal njury, damage to property or damage to the equpment. 2.3 Mantenance and Repar Never open the housng of the VdeoJet X10 SN. The unt does not contan any userservceable parts. Never open the housng of the power supply unt. The power supply unt does not contan any user-servceable parts. Ensure that all mantenance or repar work s carred out only by qualfed personnel (electrcal engneers or network technology specalsts). Bosch Securty Systems Installaton and Operatng Manual DOC V

10 10 en Safety Informaton VdeoJet X10 SN DOC V Installaton and Operatng Manual Bosch Securty Systems

11 VdeoJet X10 SN Product Descrpton en 11 3 Product Descrpton 3.1 Scope of Delvery VdeoJet X10 SN network vdeo server 4 termnal blocks Quck Installaton Gude Product CD wth the followng content: Quck Installaton Gude Manual System Requrements document Further documentaton on Bosch Securty Systems products Confguraton Manager MPEG ActveX control Player and Archve Player DrectX control Mcrosoft Internet Explorer Sun JVM Adobe Acrobat Reader Check that the delvery s complete and n perfect condton. Arrange for the unt to be checked by Bosch Securty Systems f you fnd any damage. Bosch Securty Systems Installaton and Operatng Manual DOC V

12 12 en Product Descrpton VdeoJet X10 SN 3.2 System Requrements General Requrements Computer wth Wndows XP or Wndows Vsta operatng system Network access (Intranet or Internet) Screen resoluton 1, pxels 16- or 32-bt color depth Installed Sun JVM Also note the nformaton n the System Requrements document on the product CD suppled. If necessary, you can nstall the requred programs and controls from the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). The Web browser must be confgured to enable Cookes to be set from the IP address of the unt. In Wndows Vsta, deactvate protected mode on the Securty tab under Internet Optons. You can fnd notes on usng Mcrosoft Internet Explorer n the onlne Help n Internet Explorer. Addtonal Confguraton Requrements Mcrosoft Internet Explorer (verson 6.0 or hgher) or Installed Confguraton Manager program (verson 2.0 or hgher) Addtonal Operatonal Requrements Mcrosoft Internet Explorer (verson 6.0 or hgher) or Recever software, for example VIDOS (verson 3.11 or hgher) or Bosch Vdeo Management System (verson 2.02 or hgher) or MPEG-4 compatble hardware decoder from Bosch Securty Systems (for example VIP XD) as a recever and connected vdeo montor For playng back recordngs: connecton to storage medum DOC V Installaton and Operatng Manual Bosch Securty Systems

13 VdeoJet X10 SN Product Descrpton en Overvew of Functons Network Vdeo Server The VdeoJet X10 SN s a compact network vdeo server for a connected vdeo source. It s prmarly desgned for encodng vdeo, audo and control data for transfer over an IP network. Wth ts encodng n the MPEG-4 format, the VdeoJet X10 SN s deally suted for makng exstng analog CCTV cameras IP-compatble and for remote access to dgtal VCRs and multplexers. The use of exstng networks means that ntegraton wth CCTV systems or local networks can be acheved quckly and easly. Two unts, for example a VdeoJet X10 SN as a sender and a VIP XD as a recever, can create a standalone system for data transfer wthout a PC. Vdeo mages from a sngle sender can be receved smultaneously on multple recevers. Audo sgnals can also be transmtted from and to compatble unts. Recever Compatble MPEG-4 enabled hardware decoders (for example the VIP XD) can be used as recevers. Computers wth decodng software such as VIDOS or computers wth the Mcrosoft Internet Explorer Web browser can also be used as recevers. Vdeo Encodng The VdeoJet X10 SN uses the MPEG-4 and H.264 vdeo compresson standards. Thanks to effcent encodng, the data rate remans low even wth hgh mage qualty and can also be adapted to local condtons wthn wde lmts. Dual Streamng Dual Streamng allows the ncomng data stream to be encoded smultaneously accordng to two dfferent, ndvdually customzed profles. Ths feature creates two data streams that can serve dfferent purposes, for example one for recordng and one optmzed for lve transmsson over the LAN. Multcast In sutably confgured networks, the multcast functon enables smultaneous real-tme vdeo transmsson to multple recevers. The UDP and IGMP V2 protocols must be mplemented on the network for ths functon. Encrypton The VdeoJet X10 SN offers a varety of optons for protecton aganst unauthorzed readng. Web browser connectons can be protected usng HTTPS. You can protect the control channels va the SSL encrypton protocol. Wth an addtonal lcense, the user data tself can be encrypted. Bosch Securty Systems Installaton and Operatng Manual DOC V

14 14 en Product Descrpton VdeoJet X10 SN Remote Control For remote control of external unts such as pan or tlt heads for cameras or motorzed zoom lenses, control data s transmtted va the VdeoJet X10 SN's bdrectonal seral nterface. Ths nterface can also be used to transmt transparent data. Tamper Detecton and Moton Detectors The VdeoJet X10 SN offers a wde range of confguraton optons for alarm sgnalng n the event of tamperng wth the connected camera. An algorthm for detectng movement n the vdeo mage s also part of the scope of delvery and can optonally be extended to nclude specal vdeo analyss algorthms. Snapshots Indvdual vdeo frames (snapshots) can be called up as JPEG mages by the VdeoJet X10 SN, stored on the computer's hard drve or dsplayed n a separate browser wndow. Recordngs Varous local memory optons enable the VdeoJet X10 SN to be used as a dgtal VCR. The VdeoJet X10 SN supports ANR technology, whch guarantees seamless recordng wthout gaps va VIDOS-NVR, even durng network falures. A connecton to an approprately confgured SCSI system enables long-term recordngs wth hgh mage qualty over the network. Backup A functon for storng the vdeo mages dsplayed on the hard drve of your computer s avalable on the LIVEPAGE as well as on the RECORDINGS page. Vdeo sequences can be stored by means of a mouse clck and can be redsplayed usng the Player suppled as part of the scope of delvery. DOC V Installaton and Operatng Manual Bosch Securty Systems

15 VdeoJet X10 SN Product Descrpton en 15 Summary The VdeoJet X10 SN provdes the followng man functons: Vdeo and data transmsson over IP data networks Dual Streamng functon for the encoder for smultaneous encodng wth two ndvdually defnable profles Multcast functon for smultaneous mage transmsson to multple recevers One analog BNC composte vdeo nput (PAL/NTSC) Vdeo encodng to nternatonal standard MPEG-4 Integrated Ethernet port (10/100 Base-T) CF slot for CompactFlash cards for local storage USB nterfaces for future WAN or WLAN connectons Transparent, bdrectonal data channel va RS-232/RS-422/RS-485 seral nterface Confguraton and remote control of all nternal functons va TCP/IP, also secured va HTTPS Password protecton to prevent unauthorzed connecton or confguraton changes Extensve, flexble storage optons Four alarm nputs and four relay outputs Bult-n vdeo sensor for moton and tamper alarms Event-controlled automatc connecton Convenent mantenance va uploads Flexble encrypton of control and data channels Authentcaton accordng to nternatonal standard 802.1x Transmsson and recept of audo sgnals Bdrectonal audo (mono) for lne connectons Audo encodng to nternatonal standard G.711 Bosch Securty Systems Installaton and Operatng Manual DOC V

16 16 en Product Descrpton VdeoJet X10 SN 3.4 Connectons on the Front Panel 1 USB nterface for future expanson of functons 2 Vdeo In vdeo nput BNC socket for connectng the vdeo source 3 Audo In audo lne nput 3.5 mm stereo socket for connectng an audo lne nput sgnal 4 Audo Out audo lne output 3.5 mm stereo socket for connectng an audo lne output sgnal 5 Connect LED flashes green when the unt s connected to a vdeo 6 CF LED flashes orange when actvty s detected on the CF card DOC V Installaton and Operatng Manual Bosch Securty Systems

17 VdeoJet X10 SN Product Descrpton en Connectons on the Rear Panel 7 ETH RJ45 socket for connectng to an Ethernet LAN (local network), 10/100 MBt Base-T 8 ETH LED lghts up yellow when the unt s connected to the network va ETH 9 Termnal block for alarm nputs, relay outputs, seral nterface and power supply 10 Factory reset button to restore factory default settngs 11 Compact Flash slot for a CF card type I or type II For more nformaton about the LEDs, see Secton 8.4 LEDs, page 107. For termnal block assgnment, see Secton 8.8 Termnal Block, page 109. Bosch Securty Systems Installaton and Operatng Manual DOC V

18 18 en Product Descrpton VdeoJet X10 SN DOC V Installaton and Operatng Manual Bosch Securty Systems

19 VdeoJet X10 SN Installaton en 19 4 Installaton 4.1 Preparatons! CAUTION! The unt s ntended for use ndoors or n housngs. Select a sutable locaton for nstallaton that guarantees to meet the envronmental condtons. The ambent temperature must be between 0 and +50 C (+32 and +122 F). The relatve humdty must not exceed 95%. The VdeoJet X10 SN generates heat durng operaton, so you should ensure that there s adequate ventlaton and enough clearance between the unt and heat-senstve objects or equpment. Please ensure the followng nstallaton condtons: Do not nstall the unt close to heaters or other heat sources. Avod locatons exposed to drect sunlght. Allow suffcent space for runnng cables. Ensure that the unt has adequate ventlaton. When makng connectons, use only the cables suppled or use approprate cables mmune to electromagnetc nterference. Poston and run all cables so that they are protected from damage, and provde adequate cable stran relef where needed. Avod mpacts, blows and severe vbratons that exceed the specfcaton lmts (see Secton 9 Specfcatons, page 113), as these can rreparably damage the unt. 4.2 Mountng You can purchase a rack-mount kt from Bosch Securty Systems, whch s desgned to accommodate three VdeoJet X10 SN. Bosch Securty Systems Installaton and Operatng Manual DOC V

20 20 en Installaton VdeoJet X10 SN 4.3 Connectons Camera You can connect a vdeo source to the VdeoJet X10 SN. Any cameras and other vdeo sources that produce a standard PAL or NTSC sgnal are sutable. 1. Connect the camera or another vdeo source to the BNC Vdeo In socket usng a vdeo cable (75 Ohm, BNC plug). 2. If the vdeo sgnal s not looped through, termnaton s performed by a software settng f necessary (see Secton 5.17 Advanced Mode: Vdeo Input, page 44). Audo Connectons The VdeoJet X10 SN has two audo ports for audo lne sgnals. The audo sgnals are transmtted two-way and n sync wth the vdeo sgnals. As a result, you can connect a speaker or door ntercom system at the destnaton pont, for example. The followng specfcatons should be compled wth n all cases. 1 Lne In: Impedance 9 kohm typ., 5.5 V p-p max. nput voltage 1 Lne Out: Impedance 10 kohm typ., 3.0 V p-p max. output voltage, mpedance 16 Ohm mn., 1.7 V p-p max. output voltage The stereo plugs must be connected as follows: Contact Lne In functon Lne Out functon Tp Channel 1 Channel 1 Mddle rng Lower rng Ground Ground 1. Connect an audo source wth lne level to the Audo In socket of the VdeoJet X10 SN wth a 3.5 mm stereo plug. 2. Connect a unt wth lne-n connecton to the Audo Out socket of the VdeoJet X10 SN wth a 3.5 mm stereo plug. Network You can connect the VdeoJet X10 SN to a 10/100 Base-T network usng a standard UTP category 5 cable wth RJ45 plugs. Connect the VdeoJet X10 SN to the network va the ETH socket. CF Slot You can nsert a type I or II CompactFlash card nto the Compact Flash slot to enable recordngs to be saved locally. CF cards are the deal soluton for shorter storage tmes and temporary recordngs, for example alarm recordngs or local bufferng n the event of network nterruptons. You can obtan a lst of compatble CF cards from your suppler or drectly from Bosch Securty Systems. Ths lst s constantly beng updated and extended. Playng back recordngs s also possble usng a dfferent VdeoJet X10, a VdeoJet X20 or a VdeoJet X40. DOC V Installaton and Operatng Manual Bosch Securty Systems

21 VdeoJet X10 SN Installaton en 21! CAUTION! If the card s formatted, all exstng data s deleted from the card. You should therefore check whether the CF card contans any data that needs to be backed up before t s nserted. 1. Carefully slde the CF card, top sde down, nto the slot as far as t wll go. 2. To remove the CF card, smply pull t out. Data Interface The bdrectonal data nterface s used to control unts connected to the VdeoJet X10 SN, such as a dome camera wth a motorzed lens. The connecton supports the RS-232, RS-422 and RS-485 transmsson standards. The VdeoJet X10 SN offers the seral nterface va the orange termnal block (see Secton 8.8 Termnal Block, page 109). The range of controllable equpment s expandng constantly. The manufacturers of the relevant equpment provde specfc nformaton on nstallaton and control.! CAUTION! Please take note of the approprate documentaton when nstallng and operatng the unt to be controlled. The documentaton contans mportant safety nstructons and nformaton about permtted uses. A vdeo connecton s necessary to transmt transparent data. Alarm Inputs The VdeoJet X10 SN has four alarm nputs on the orange termnal block (see Secton 8.8 Termnal Block, page 109). The alarm nputs are used to connect to external alarm devces such as door contacts or sensors. Wth the approprate confguraton, an alarm sensor can automatcally connect the VdeoJet X10 SN to a remote locaton, for example. A zero potental closng contact or swtch can be used as the actuator. If possble, use a bounce-free contact system as the actuator. Connect the lnes to the approprate termnals on the orange termnal block (IN1 to IN4) and check that the connecton s secure. Bosch Securty Systems Installaton and Operatng Manual DOC V

22 22 en Installaton VdeoJet X10 SN Relay Outputs The VdeoJet X10 SN has four relay outputs for swtchng external unts such as lamps or alarm srens. You can operate these relay outputs manually whle there s an actve connecton to the VdeoJet X10 SN. The outputs can also be confgured to automatcally actvate srens or other alarm unts n response to an alarm sgnal. The relay outputs are also located on the orange termnal block (see Secton 8.8 Termnal Block, page 109).! CAUTION! A maxmum load of 30 V and 2 A (SELV) may be appled to the relay contacts. Connect the lnes to the approprate termnals on the orange termnal block (R1 to R4) and check that the connecton s secure. Remote Indcaton of the Connecton Status When the VdeoJet X10 SN s connected to a vdeo, the Connect LED on the front panel of the unt flashes. The LED also provdes nformaton on the operatonal state of the unt and sgnals a unt defect (see Secton 8.4 LEDs, page 107). You can connect an addtonal two-color LED to the VdeoJet X10 SN as a remote ndcator. Ths provdes the same nformaton as the ntegrated Connect LED. A remote ndcator can be useful f the VdeoJet X10 SN s nstalled at a locaton that s dffcult to access or see, for example n a cable duct or on top of a mast. Just lke the ntegrated LED, the remote ndcator LED should also lght up red and green n order to avod confuson. Please comply wth the followng specfcatons and the connecton dagram: Voltage between RM1 and RM2 Current between RM1 and RM2 Source resstance 3.3 V DC max. 25 ma max. 140 Ohm typ. 1. Connect the LED lnes to the approprate termnals on the orange termnal block (RM1 and RM2) and check that the connecton s secure. 2. Check that the sgnals on the Connect LED on the VdeoJet X10 SN and the remote ndcator LED correspond. DOC V Installaton and Operatng Manual Bosch Securty Systems

23 VdeoJet X10 SN Installaton en 23 Backup Power Supply If the VdeoJet X10 SN does not have a permanent power supply, t may be necessary to supply the nternal clock separately. To do ths, you can connect the VdeoJet X10 SN drectly to a battery va the BP and GND contacts. The correct tme s crucal for evaluatng local recordngs.! CAUTION! Connect only batteres wth the followng specfcaton: 10 to 30 V DC, 50 Ah max., 12/24 V contnuous flow. 1. Connect the + (plus) lne on the battery to the BP termnal on the orange termnal block. 2. Connect the (mnus) lne on the battery to the GND termnal on the orange termnal block. 3. Now check that the connectons are secure. If you do not connect a battery to the unt, you should specfy a tme server to ensure correct system tme. Bosch Securty Systems Installaton and Operatng Manual DOC V

24 24 en Installaton VdeoJet X10 SN 4.4 Power On/Power Off Power Supply The VdeoJet X10 SN does not have a power swtch. Power s suppled va a separate unt. Connect the VdeoJet X10 SN to the power supply unt and plug ths nto the mans. The unt s now ready for use. The VdeoJet X10 SN does not come suppled wth a power supply unt.! CAUTION! Use only power supply unts wth UL approval and a power output accordng to LPS or NEC Class 2. Where necessary, use sutable equpment to ensure that the power supply s free from nterference such as voltage surges, spkes or voltage drops. Do not connect the VdeoJet X10 SN to the power supply untl all other connectons have been made. 1. Plug the termnal block wth the PSU cable connected to t nto the orange socket on the VdeoJet X10 SN. 2. Connect the power supply unt to the mans. The VdeoJet X10 SN s ready for use as soon as the Connect LED changes from a red lght, ndcatng the start-up procedure, to a green lght. Provded the network connecton has been correctly made, the yellow ETH LED also lghts up. A flashng ETH LED sgnals that data packets are beng transmtted va the network. 4.5 Setup Usng the Confguraton Manager The Confguraton Manager program can be found on the product CD contaned n the scope of delvery. Ths program allows you to mplement and set up new vdeo servers n the network quckly and convenently. Usng the Confguraton Manager to set all parameters n the VdeoJet X10 SN s an alternatve to confguraton by means of a Web browser, as descrbed n chapter 5 of ths manual. Installng the Program 1. Insert the CD nto the computer's CD-ROM drve. 2. If the CD does not start automatcally, open the Confguraton Manager drectory usng Wndows Explorer and double-clck Setup.exe. 3. Follow the on-screen nstructons. DOC V Installaton and Operatng Manual Bosch Securty Systems

25 VdeoJet X10 SN Installaton en 25 Confgurng the VdeoJet X10 SN You can start the Confguraton Manager mmedately after nstallaton. 1. Double-clck the con on the desktop or start the program va the Start menu. After the program has started, the network s mmedately searched for compatble vdeo servers. 2. You can start the confguraton f a VdeoJet X10 SN s shown n the lst n the left secton of the wndow. To do ths, rght-clck the entry for the unt. 3. Clck Unt network settngs... n the popup menu. 4. In the Unt IP address feld, enter a vald IP address for your network (for example ) and clck OK. The unt reboots and the IP address s vald. 5. If requred, enter an approprate subnet mask for the IP address, and addtonal network data. You must reboot to actvate the new IP address, a new subnet mask or a gateway IP address. Reboot You can trgger the reboot drectly wth the assstance of the Confguraton Manager. Rght-clck the entry for the unt n the lst n the left secton of the wndow and select the Reset command from the context menu. Addtonal Parameters You can check and set addtonal parameters wth the assstance of the Confguraton Manager. You can fnd detaled nformaton on ths n the documentaton for ths program. Bosch Securty Systems Installaton and Operatng Manual DOC V

26 26 en Installaton VdeoJet X10 SN DOC V Installaton and Operatng Manual Bosch Securty Systems

27 VdeoJet X10 SN Confguraton Usng a Web Browser en 27 5 Confguraton Usng a Web Browser 5.1 Connectng The ntegrated HTTP server n the VdeoJet X10 SN provdes you wth the opton to confgure the unt over the network wth a Web browser. Ths opton s an alternatve to confguraton usng the Confguraton Manager program and s consderably rcher n functon and more convenent than confguraton usng the termnal program. System Requrements Computer wth Wndows XP or Wndows Vsta operatng system Network access (Intranet or Internet) Mcrosoft Internet Explorer (verson 6.0 or hgher) Screen resoluton 1, pxels 16- or 32-bt color depth Installed Sun JVM Also note the nformaton n the System Requrements document on the product CD suppled. If necessary, you can nstall the requred programs and controls from the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). The Web browser must be confgured to enable Cookes to be set from the IP address of the unt. In Wndows Vsta, deactvate protected mode on the Securty tab under Internet Optons. You can fnd notes on usng Mcrosoft Internet Explorer n the onlne Help n Internet Explorer. Installng MPEG ActveX Sutable MPEG ActveX software must be nstalled on the computer to allow the lve vdeo mages to be played back. If necessary, you can nstall the program from the product CD suppled. 1. Insert the product CD nto the computer's CD-ROM drve. If the CD does not start automatcally, open the root drectory of the CD n Wndows Explorer and double-clck MPEGAx.exe. 2. Follow the on-screen nstructons. Bosch Securty Systems Installaton and Operatng Manual DOC V

28 28 en Confguraton Usng a Web Browser VdeoJet X10 SN Establshng the Connecton Before you can operate the VdeoJet X10 SN wthn your network, t must have a vald IP address for your network and a compatble subnet mask. The followng default address s preset at the factory: Start the Web browser. 2. Enter the IP address of the VdeoJet X10 SN as the URL. The connecton s establshed and after a short tme you wll see the LIVEPAGE wth the vdeo mage. Maxmum Number of Connectons If you do not connect, the unt may have reached ts maxmum number of connectons. Dependng on the unt and network confguraton, each VdeoJet X10 SN can have up to 25 Web browser connectons or up to 50 connectons va VIDOS or Bosch Vdeo Management System. DOC V Installaton and Operatng Manual Bosch Securty Systems

29 VdeoJet X10 SN Confguraton Usng a Web Browser en 29 Protected VdeoJet X10 SN If the VdeoJet X10 SN s password protected aganst unauthorzed access, the Web browser dsplays a correspondng message and prompts you to enter the password when you attempt to access protected areas. The VdeoJet X10 SN offers the opton to lmt the extent of access usng varous authorzaton levels (see Secton 5.11 Advanced Mode: Password, page 38). 1. Enter the user name and assocated password n the correspondng text felds. 2. Clck OK. If the password s entered correctly, the Web browser dsplays the page that was called up. Protected Network If a RADIUS server s employed n the network for managng access rghts (802.1x authentcaton), the VdeoJet X10 SN must be confgured accordngly, otherwse no communcaton s possble. To confgure the unt, you must connect the VdeoJet X10 SN drectly to a computer usng a network cable. Ths s because communcaton va the network s not enabled untl the Identty and Password parameters have been set and successfully authentcated (see Secton Authentcaton, page 80). 5.2 Confguraton Menu The SETTINGS page provdes access to the confguraton menu, whch contans all the unt's parameters arranged n groups. You can vew the current settngs by openng one of the confguraton screens. You can change the settngs by enterng new values or by selectng a predefned value from a lst feld. There are two optons for confgurng the unt or checkng the current settngs: Basc mode Advanced mode In Basc Mode the most mportant parameters are arranged n seven groups. Ths allows you to change the basc settngs wth just a few entres and then put the devce nto operaton. Advanced Mode s recommended for expert users or system support personnel. You can access all unt parameters n ths mode. Settngs that affect the fundamental functonalty of the unt (such as frmware updates) can only be altered n the advanced mode. All parameter groups are descrbed n ths chapter n the order n whch they are lsted n the confguraton menu, from the top of the screen to the bottom.! CAUTION! The settngs n the advanced mode should only be processed or modfed by expert users or system support personnel. All settngs are backed up n the VdeoJet X10 SN memory so they are not lost even f the power fals. Bosch Securty Systems Installaton and Operatng Manual DOC V

30 30 en Confguraton Usng a Web Browser VdeoJet X10 SN Startng Confguraton Clck the SETTINGS lnk n the upper secton of the wndow. The Web browser opens a new page wth the confguraton menu. Navgaton 1. Clck one of the menu tems n the left wndow margn. The correspondng submenu s dsplayed. 2. Clck one of the entres n the submenu. The Web browser opens the correspondng page. Makng Changes Each confguraton screen shows the current settngs. You can change the settngs by enterng new values or by selectng a predefned value from a lst feld. After each change, clck Set to save the change.! CAUTION! Save each change wth the assocated Set button. Clckng the Set button saves the settngs only n the current feld. Changes n any other felds are gnored. DOC V Installaton and Operatng Manual Bosch Securty Systems

31 VdeoJet X10 SN Confguraton Usng a Web Browser en Basc Mode: Unt Access Devce name You can gve the VdeoJet X10 SN a name to make t easer to dentfy. The name makes the task of admnsterng multple unts n larger vdeo montorng systems easer, for example usng the VIDOS or Bosch Vdeo Management System programs. The devce name s used for the remote dentfcaton of a unt, n the event of an alarm for example. For ths reason, enter a name that makes t as easy as possble to quckly dentfy the locaton.! CAUTION! Do not use any specal characters, for example &, n the name. Specal characters are not supported by the system's nternal recordng management and may therefore result n the Player or Archve Player beng unable to play back the recordng. Camera 1 The camera name makes t easer to dentfy the remote camera locaton, n the event of an alarm for example. It wll be dsplayed n the vdeo screen f confgured to do so (see Secton Camera name stampng, page 40). The camera name makes the task of admnsterng cameras n larger vdeo montorng systems easer, for example usng the VIDOS or Bosch Vdeo Management System programs. Enter a unque, unambguous name for the camera n ths feld.! CAUTION! Do not use any specal characters, for example &, n the name. Specal characters are not supported by the system's nternal recordng management and may therefore result n the Player or Archve Player beng unable to play back the recordng. Password A VdeoJet X10 SN s generally protected by a password to prevent unauthorzed access to the unt. You can use dfferent authorzaton levels to lmt access. The VdeoJet X10 SN operates wth three authorzaton levels: servce, user and lve. Bosch Securty Systems Installaton and Operatng Manual DOC V

32 32 en Confguraton Usng a Web Browser VdeoJet X10 SN The hghest authorzaton level s servce. After enterng the correct password, you can access all the functons of the VdeoJet X10 SN and change all confguraton settngs. Wth the user authorzaton level, you can operate the unt and also control cameras, for example, but you cannot change the confguraton. The lowest authorzaton level s lve. It can only be used to vew the lve vdeo mage and swtch between the dfferent lve mage dsplays. You can defne and change a password for each authorzaton level f you are logged n as servce or f the unt s not password protected. Enter the password for the approprate authorzaton level here. Proper password protecton s only guaranteed when all hgher authorzaton levels are also protected wth a password. If a lve password s assgned, for example, a servce and a user password must also be set. When assgnng passwords, you should therefore always start from the hghest authorzaton level, servce, and use dfferent passwords. Confrm password In each case, enter the new password a second tme to elmnate typng mstakes. A new password s only saved when you clck the Set button. You should therefore clck the Set button mmedately after enterng and confrmng a password. 5.4 Basc Mode: Date/Tme Unt date/unt tme/unt tme zone If there are multple devces operatng n your system or network, t s mportant to synchronze ther nternal clocks. For example, t s only possble to dentfy and correctly evaluate smultaneous recordngs when all unts are operatng on the same tme. If necessary, you can synchronze the unt wth your computer's system settngs. Clck the Sync to PC button to copy your computer's system tme to the VdeoJet X10 SN. Tme server IP address The VdeoJet X10 SN can receve the tme sgnal from a tme server usng varous tme server protocols, and then use t to set the nternal clock. The unt polls the tme sgnal automatcally once every mnute. Enter the IP address of a tme server here. DOC V Installaton and Operatng Manual Bosch Securty Systems

33 VdeoJet X10 SN Confguraton Usng a Web Browser en 33 Tme server type Select the protocol that s supported by the selected tme server. Preferably, you should select the SNTP server as the protocol. Ths supports a hgh level of accuracy and s requred for specal applcatons and subsequent functon extensons. Select Tme server for a tme server that works wth the protocol RFC Basc Mode: Network The settngs on ths page are used to ntegrate the VdeoJet X10 SN nto an exstng network. Some changes only take effect after the unt s rebooted. In ths case, the Set button changes to Set and Reboot. 1. Make the desred changes. 2. Clck the Set and Reboot button. The VdeoJet X10 SN s rebooted and the changed settngs are actvated.! CAUTION! If you change the IP address, subnet mask or gateway address, the VdeoJet X10 SN s only avalable under the new addresses after the reboot. DHCP If a DHCP server s employed n the network for the dynamc assgnment of IP addresses, you can actvate acceptance of IP addresses automatcally assgned to the VdeoJet X10 SN. Certan applcatons (VIDOS, Bosch Vdeo Management System, Archve Player, Confguraton Manager) use the IP address for the unque assgnment of the unt. If you use these applcatons, the DHCP server must support the fxed assgnment between IP address and MAC address, and must be approprately set up so that, once an IP address s assgned, t s retaned each tme the system s rebooted. IP address Enter the desred IP address for the VdeoJet X10 SN n ths feld. The IP address must be vald for the network. Subnet mask Enter the approprate subnet mask for the selected IP address here. Gateway address If you want the unt to establsh a connecton to a remote locaton n a dfferent subnet, enter the IP address of the gateway here. Otherwse leave the box blank ( ). Bosch Securty Systems Installaton and Operatng Manual DOC V

34 34 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.6 Basc Mode: Encoder Profle Actve profle You can select a profle for encodng the vdeo sgnal. You can use ths to adapt the vdeo data transmsson to the operatng envronment (for example network structure, bandwdth, data load). Pre-programmed profles are avalable, each gvng prorty to dfferent perspectves. When selectng a profle, detals are dsplayed n the lst feld. Low bandwdth (CIF) Hgh qualty for low bandwdth connectons, resoluton /240 pxels Low delay (2/3 D1) Hgh qualty wth low delay, resoluton /480 pxels Hgh resoluton (4CIF/D1) Hgh resoluton for hgh bandwdth connectons, resoluton /480 pxels DSL For DSL connectons wth 500 kbps, resoluton /240 pxels ISDN (2B) For ISDN connectons va two B-channels, resoluton /240 pxels ISDN (1B) For ISDN connectons va one B-channel, resoluton /240 pxels Modem For analog modem connectons wth 20 kbps, resoluton /240 pxels GSM For GSM connectons at 9,600 baud, resoluton /120 pxels DOC V Installaton and Operatng Manual Bosch Securty Systems

35 VdeoJet X10 SN Confguraton Usng a Web Browser en Basc Mode: Audo You can set the gan of the audo sgnals to sut your specfc requrements. The current vdeo mage s shown n the small wndow next to the slde controls to help you check the audo source and mprove assgnments. Your changes are effectve mmedately. If you connect va Web browser, you must actvate the audo transmsson on the LIVEPAGE Functons page (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). For other connectons, the transmsson depends on the audo settngs of the respectve system. Audo The audo sgnals are sent n a separate data stream parallel to the vdeo data, and so ncrease the network load. The audo data are encoded accordng to G.711 and requre an addtonal bandwdth of approx. 80 kbps for each connecton. If you do not want any audo data to be transmtted, select Off. Lne In 1 You can set the lne nput gan. Make sure that the dsplay does not go beyond the green zone durng modulaton. Lne Out You can set the lne output gan. Make sure that the dsplay does not go beyond the green zone durng modulaton. 5.8 Basc Mode: Recordng You can record the mages from the camera connected to the VdeoJet X10 SN on varous local storage meda or on an approprately confgured SCSI system. CF cards (see Secton CF Slot, page 20) are the deal soluton for shorter storage tmes. f the VdeoJet X10 SN has a USB hard drve, ths s sutable for longer, local recordngs. For long-term, authortatve mages, t s essental that you use an approprately szed SCSI system. Here you can select a storage medum and mmedately start or stop the recordng. Storage medum 1. Select the requred storage medum from the lst. 2. Clck the Start button to start the recordng mmedately. Bosch Securty Systems Installaton and Operatng Manual DOC V

36 36 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.9 Basc Mode: System Overvew The data on ths page are for nformaton purposes only and cannot be changed. Keep a record of ths nformaton n case techncal assstance s requred. You can select all requred text on ths page wth the mouse and copy t to the clpboard wth the [Ctrl]+[C] key combnaton, for example f you want to send t va e-mal Advanced Mode: Identfcaton Devce ID Each VdeoJet X10 SN should be assgned a unque dentfer that you can enter here as an addtonal means of dentfcaton. Devce name You can gve the VdeoJet X10 SN a name to make t easer to dentfy. The name makes the task of admnsterng multple unts n larger vdeo montorng systems easer, for example usng the VIDOS or Bosch Vdeo Management System programs. DOC V Installaton and Operatng Manual Bosch Securty Systems

37 VdeoJet X10 SN Confguraton Usng a Web Browser en 37 The devce name s used for the remote dentfcaton of a unt, n the event of an alarm for example. For ths reason, enter a name that makes t as easy as possble to quckly dentfy the locaton.! CAUTION! Do not use any specal characters, for example &, n the name. Specal characters are not supported by the system's nternal recordng management and may therefore result n the Player or Archve Player beng unable to play back the recordng. Camera 1 The camera name makes t easer to dentfy the remote camera locaton, n the event of an alarm for example. It wll be dsplayed n the vdeo screen f confgured to do so (see Secton Camera name stampng, page 40). The camera name makes the task of admnsterng cameras n larger vdeo montorng systems easer, for example usng the VIDOS or Bosch Vdeo Management System programs. Enter a unque, unambguous name for the camera n ths feld. You can use both lnes for ths.! CAUTION! Do not use any specal characters, for example &, n the name. Specal characters are not supported by the system's nternal recordng management and may therefore result n the Player or Archve Player beng unable to play back the recordng. You can use the second lne for enterng addtonal characters; these can be selected from a table. 1. Clck the con next to the second lne. A new wndow wth the character map s opened. 2. Clck the requred character. The character s nserted nto the Result feld. 3. In the character map, clck the << and >> cons to move between the dfferent pages of the table, or select a page from the lst feld. 4. Clck the < con to the rght of the Result feld to delete the last character, or clck the X con to delete all characters. 5. Now clck the OK button to apply the selected characters to the second lne of the Camera 1 parameters. The wndow wll close. Intator extenson You can attach your own text to the ntator name of the VdeoJet X10 SN to make the unt easer to dentfy n large SCSI systems. Ths text s added to the ntator name, separated from t by a full stop. You can see the ntator name n the system overvew (see Secton 5.9 Basc Mode: System Overvew, page 36). Bosch Securty Systems Installaton and Operatng Manual DOC V

38 38 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.11 Advanced Mode: Password A VdeoJet X10 SN s generally protected by a password to prevent unauthorzed access to the unt. You can use dfferent authorzaton levels to lmt access. Proper password protecton s only guaranteed when all hgher authorzaton levels are also protected wth a password. If a lve password s assgned, for example, a servce and a user password must also be set. When assgnng passwords, you should therefore always start from the hghest authorzaton level, servce, and use dfferent passwords. Password The VdeoJet X10 SN operates wth three authorzaton levels: servce, user and lve. The hghest authorzaton level s servce. After enterng the correct password, you can access all the functons of the VdeoJet X10 SN and change all confguraton settngs. Wth the user authorzaton level, you can operate the unt and also control cameras, for example, but you cannot change the confguraton. The lowest authorzaton level s lve. It can only be used to vew the lve vdeo mage and swtch between the dfferent lve mage dsplays. You can defne and change a password for each authorzaton level f you are logged n as servce or f the unt s not password protected. Enter the password for the approprate authorzaton level here. Confrm password In each case, enter the new password a second tme to elmnate typng mstakes. A new password s only saved when you clck the Set button. You should therefore clck the Set button mmedately after enterng and confrmng a password. DOC V Installaton and Operatng Manual Bosch Securty Systems

39 VdeoJet X10 SN Confguraton Usng a Web Browser en Advanced Mode: Date/Tme Date format Select your requred date format. Unt date/unt tme If there are multple devces operatng n your system or network, t s mportant to synchronze ther nternal clocks. For example, t s only possble to dentfy and correctly evaluate smultaneous recordngs when all unts are operatng on the same tme. 1. Enter the current date. Snce the unt tme s controlled by the nternal clock, there s no need to enter the day of the week t s added automatcally. 2. Enter the current tme or clck the Sync to PC button to copy your computer's system tme to the VdeoJet X10 SN. Unt tme zone Select the tme zone n whch your system s located. Daylght savng tme The nternal clock can swtch automatcally between normal and daylght savng tme (DST). The unt already contans the data for DST swtch-overs up to the year You can use these data or create alternatve tme savng data f requred. If you do not create a table, there wll be no automatc swtchng. When changng and clearng ndvdual entres, remember that two entres are usually related to each other and dependent on one another (swtchng to summer tme and back to normal tme). 1. Frst check whether the correct tme zone s selected. If t s not correct, select the approprate tme zone for the system, and clck the Set button. 2. Clck the Detals button. A new wndow wll open and you wll see the empty table. 3. Select the regon or the cty that s closest to the system's locaton from the lst feld below the table. 4. Clck the Generate button to generate data and enter t nto the table. 5. Make changes by clckng an entry n the table. The entry s selected. 6. Clckng the Delete button wll remove the entry from the table. 7. Select other values from the lst felds below the table to change the entry. Changes are made mmedately. Bosch Securty Systems Installaton and Operatng Manual DOC V

40 40 en Confguraton Usng a Web Browser VdeoJet X10 SN 8. If there are empty lnes at the bottom of the table, for example after deletons, you can add new data by markng the row and selectng requred values from the lst felds. 9. Now clck the OK button to save and actvate the table. Tme server IP address The VdeoJet X10 SN can receve the tme sgnal from a tme server usng varous tme server protocols, and then use t to set the nternal clock. The unt polls the tme sgnal automatcally once every mnute. Enter the IP address of a tme server here. Tme server type Select the protocol that s supported by the selected tme server. Preferably, you should select the SNTP server as the protocol. Ths supports a hgh level of accuracy and s requred for specal applcatons and subsequent functon extensons. Select Tme server for a tme server that works wth the protocol RFC Advanced Mode: Dsplay Stampng Varous overlays or "stamps" n the vdeo mage provde mportant supplementary nformaton. These overlays can be enabled ndvdually and are arranged on the mage n a clear manner. Camera name stampng Ths feld sets the poston of the camera name overlay. It can be dsplayed at the Top, at the Bottom or at a poston of your choce that you can then specfy usng the Custom opton. Or t can be set to Off for no overlay nformaton. 1. Select the desred opton from the lst. 2. If you select the Custom opton, addtonal felds are dsplayed where you can specfy the exact poston (Poston (XY)). 3. In the Poston (XY) felds, enter the values for the desred poston. Tme stampng Ths feld sets the poston of the tme overlay. It can be dsplayed at the Top, at the Bottom or at a poston of your choce that you can then specfy usng the Custom opton. Or t can be set to Off for no overlay nformaton. 1. Select the desred opton from the lst. 2. If you select the Custom opton, addtonal felds are dsplayed where you can specfy the exact poston (Poston (XY)). 3. In the Poston (XY) felds, enter the values for the desred poston. DOC V Installaton and Operatng Manual Bosch Securty Systems

41 VdeoJet X10 SN Confguraton Usng a Web Browser en 41 Dsplay mllseconds If necessary, you can also dsplay mllseconds. Ths nformaton can be useful for recorded vdeo mages; however, t does ncrease the processor's computng tme. Select Off f you do not need to dsplay mllseconds. Alarm mode stampng Select On to dsplay a text message overlay n the event of an alarm. It can be dsplayed at a poston of your choce that you can then specfy usng the Custom opton. Or t can be set to Off for no overlay nformaton. 1. Select the desred opton from the lst. 2. If you select the Custom opton, addtonal felds are dsplayed where you can specfy the exact poston (Poston (XY)). 3. In the Poston (XY) felds, enter the values for the desred poston. Alarm message Enter the message to be dsplayed n the event of an alarm. The maxmum text length s 31 characters. Vdeo watermarkng Choose On f you wsh the transmtted vdeo mages to be "watermarked". After actvaton, all mages are marked wth a green W. A red W ndcates that the sequence (lve or saved) has been manpulated Advanced Mode: Appearance On ths page you can adapt the appearance of the web nterface and change the webste language to meet your requrements. If necessary, you can replace the manufacturer's logo (top rght) and the product name (top left) n the top part of the wndow wth ndvdual graphcs. You can use ether GIF or JPEG mages. The fle paths must correspond to the access mode (for example C:\Images\Logo.gf for access to local fles, or mages/logo.gf for access va the Internet/Intranet). When accessng va the Internet/Intranet, ensure that a connecton s always avalable to dsplay the mage. The mage fle s not stored n the VdeoJet X10 SN. Webste language Select the language for the user nterface here. Bosch Securty Systems Installaton and Operatng Manual DOC V

42 42 en Confguraton Usng a Web Browser VdeoJet X10 SN There are always two languages to choose from: Englsh and another language. If the language you requre s not avalable for selecton, you can download the current frmware wth another language combnaton from the webste Company logo Enter the path to a sutable graphc f you want to replace the manufacturer's logo. The mage fle can be stored on a local computer, n the local network or at an Internet address. Devce logo Enter the path to a sutable graphc f you want to replace the product name. The mage fle can be stored on a local computer, n the local network or at an Internet address. If you want to use the orgnal graphcs agan, smply delete the entres n the Company logo and Devce logo felds. JPEG sze You can choose between two gven mage szes to dsplay the M-JPEG mage on the LIVEPAGE. JPEG nterval You can specfy the nterval at whch the ndvdual mages should be generated for the M- JPEG mage on the LIVEPAGE. JPEG qualty You can specfy the mage qualty for dsplayng M-JPEG on the LIVEPAGE Advanced Mode: LIVEPAGE Functons DOC V Installaton and Operatng Manual Bosch Securty Systems

43 VdeoJet X10 SN Confguraton Usng a Web Browser en 43 On ths page you can adapt the LIVEPAGE functons to your requrements. You can choose from a varety of dfferent optons for dsplayng nformaton and controls. 1. Check the box for the tems that are to be made avalable on the LIVEPAGE. The selected tems are ndcated by a check mark. 2. Check whether the requred functons are avalable on the LIVEPAGE. Transmt audo The audo sgnals are sent n a separate data stream parallel to the vdeo data, and so ncrease the network load. The audo data are encoded accordng to G.711 and requre an addtonal bandwdth of approx. 80 kbps for each connecton. Blnx control Next to the feld for vew control at the top left of the LIVEPAGE, an addtonal feld s dsplayed for the specal Bosch Securty Systems Blnx control. Lease tme (s) The lease tme n seconds determnes the tme beyond whch a dfferent user s authorzed to control the camera after no further control sgnals are receved from the current user. After ths tme nterval, the camera s automatcally enabled. Show alarm nputs Alarm nputs are shown next to the vdeo mage as cons, along wth ther assgned names. If an alarm s actve, the correspondng con changes color. Show relay outputs Relay outputs are shown next to the vdeo mage as cons, along wth ther assgned names. If the relay s swtched, the con changes color. Show VCA trajectores The trajectores (moton lnes of objects) from the vdeo content analyss are dsplayed n the lve vdeo mage f a correspondng analyss type s actvated (see Secton 5.31 Advanced Mode: VCA Event Trggered, page 68). Show VCA metadata When the analyss functon s actvated, the addtonal nformaton from the vdeo content analyss (VCA) wll be dsplayed n the lve vdeo mage (see Secton 5.31 Advanced Mode: VCA Event Trggered, page 68). Wth the MOTION+ analyss type, for example, the sensor felds n whch moton s recorded wll be marked wth rectangles. Show event log The event messages are dsplayed along wth the date and tme n a feld next to the vdeo mage. Show system log The system messages are dsplayed along wth the date and tme n a feld next to the vdeo mage and provde nformaton about establshng and endng connectons, for example. Allow snapshots Here you can specfy whether the con for savng ndvdual mages should be dsplayed below the lve mage. Indvdual mages can only be saved f ths con s vsble. Allow local recordng Here you can specfy whether the con for savng vdeo sequences on the local memory should be dsplayed below the lve mage. Vdeo sequences can only be saved f ths con s vsble. Bosch Securty Systems Installaton and Operatng Manual DOC V

44 44 en Confguraton Usng a Web Browser VdeoJet X10 SN Path for JPEG and MPEG fles 1. Enter the path for the storage locaton of ndvdual mages and vdeo sequences that you can save from the LIVEPAGE. 2. If necessary, clck Browse to fnd a sutable drectory Advanced Mode: Loggng Save event log Check ths opton to save event messages n a text fle on your local computer. You can then vew, edt and prnt ths fle wth any text edtor or the standard Offce software. Fle for event log 1. Enter the path for savng the event log here. 2. If necessary, clck Browse to fnd a sutable drectory. Save system log Check ths opton to save system messages n a text fle on your local computer. You can then vew, edt and prnt ths fle wth any text edtor or the standard Offce software. Fle for system log 1. Enter the path for savng the system log here. 2. If necessary, clck Browse to fnd a sutable drectory Advanced Mode: Vdeo Input You can actvate the 75 Ohm termnatng resstance for the vdeo nput of the VdeoJet X10 SN. The termnatng resstance must be deactvated for the vdeo sgnal to be looped through. Every vdeo nput s closed at the tme of delvery. 75 Ohm termnaton nput 1 Select Off f the vdeo sgnal s to be looped through. Source type nput 1 To allow VCRs to be connected as a vdeo source, you can change the characterstc of the vdeo source from the preset value of Camera to VCR. VCRs requre a more tolerant settng DOC V Installaton and Operatng Manual Bosch Securty Systems

45 VdeoJet X10 SN Confguraton Usng a Web Browser en 45 for the nternal PLL as a result of jtter effects caused by the mechancal components of a VCR. In some cases, selectng the VCR opton can lead to an mprovement n the vdeo mage even wth a camera connected Advanced Mode: Pcture Settngs You can set the vdeo mage of the camera to sut your requrements. The current vdeo mage s dsplayed n the small wndow next to the slde controls as confrmaton. Your changes are effectve mmedately. 1. Move the slde control to the requred poston. 2. Clck Default to reset all settngs to ther default value. Contrast ( ) You can use ths functon to adapt the contrast of the vdeo mage to your workng envronment. Saturaton ( ) You can use ths functon to adjust the color saturaton so as to make the reproducton of colors on your montor as realstc as possble. Brghtness ( ) You can use ths functon to adapt the brghtness of the vdeo mage to your workng envronment. Low-pass flter ( ) You can use ths functon to flter very fne nose from the mage. Ths reduces and optmzes the bandwdth necessary for mage transmsson over the network. The mage resoluton may be mpared. The hgher the value set wth the slde control, the flatter the mage sgnal. Check your settng n the mage wndow next to the slde controls. Also observe the processor load ndcator that appears at the top of the wndow near the manufacturer's logo (see Secton 8.6 Network Connecton, page 108). Bosch Securty Systems Installaton and Operatng Manual DOC V

46 46 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.19 Advanced Mode: Encoder Profle For the vdeo sgnal encodng, you can select a code algorthm for each and two profles, and you can change the presets for the profles. You can adapt the vdeo data transmsson to the operatng envronment (for example network structure, bandwdth, data load). To ths end, the VdeoJet X10 SN smultaneously generates two data streams (Dual Streamng), whch compresson settngs you can select ndvdually, for example one settng for transmssons to the Internet and one for LAN connectons. Pre-programmed profles are avalable, each gvng prorty to dfferent perspectves. Low bandwdth (CIF) Hgh qualty for low bandwdth connectons, resoluton /240 pxels Low delay (2/3 D1) Hgh qualty wth low delay, resoluton /480 pxels DOC V Installaton and Operatng Manual Bosch Securty Systems

47 VdeoJet X10 SN Confguraton Usng a Web Browser en 47 Hgh resoluton (4CIF/D1) Hgh resoluton for hgh bandwdth connectons, resoluton /480 pxels DSL For DSL connectons wth 500 kbps, resoluton /240 pxels ISDN (2B) For ISDN connectons va two B-channels, resoluton /240 pxels ISDN (1B) For ISDN connectons va one B-channel, resoluton /240 pxels Modem For analog modem connectons wth 20 kbps, resoluton /240 pxels GSM For GSM connectons at 9,600 baud, resoluton /120 pxels You can choose between the code algorthms MPEG-4 SH++ and H.264 for each data stream. H.264 requres a lower bandwdth at the same vdeo qualty but t does not offer 4CIF resoluton. 4CIF resoluton s only possble wth MPEG-4 SH Select the requred profle for every data stream. 2. Select the requred code algorthm for every data stream. You can change ndvdual parameter values of a profle and you can also change the name. You can swtch between profles by clckng the approprate tabs.! CAUTION! The profles are rather complex. They nclude a large number of parameters that nteract wth one another, so t s generally best to use the default profles. Change the profles only once you are fully famlar wth all the confguraton optons. In the default settng, Stream 2 s transmtted for alarm connectons and automatc connectons. Bear ths fact n mnd when assgnng the profle. All parameters combne to make up a profle and are dependent on one another. If you enter a settng that s outsde the permtted range for a partcular parameter, the nearest permtted value wll be substtuted when the settngs are saved. Prevew for Select whch vdeo data stream should be dsplayed n the prevews. You can deactvate the dsplay of the vdeo mages f the performance of the computer s affected too strongly by the decodng of the data streams. 1. Check the box for the requred data stream. 2. Clck the con above the relevant prevew to dsplay further nformaton about the data stream. Profle name You can enter a new name for the profle here. The name s then dsplayed n the lst of avalable profles n the Actve profle feld. Bosch Securty Systems Installaton and Operatng Manual DOC V

48 48 en Confguraton Usng a Web Browser VdeoJet X10 SN Target data rate You can lmt the data rate for the VdeoJet X10 SN to optmze utlzaton of the bandwdth n your network. The target data rate should be set accordng to the desred pcture qualty for typcal scenes wth no excessve moton. For complex mages or frequent changes of mage content due to frequent movements, ths lmt can be temporarly exceeded up to the value you enter n the Maxmum data rate feld. Encodng nterval The fgure selected here determnes the nterval at whch mages are encoded and transmtted. For example, enterng 4 means that only every fourth mage s encoded, the followng three are skpped - ths can be partcularly advantageous wth low bandwdths. The mage rate n ps (mages per second) s dsplayed next to the text feld. Vdeo resoluton Here you can select the desred resoluton for the vdeo mage. The followng resolutons are avalable: QCIF /120 pxels CIF /240 pxels 1/2 D /480 pxels 2CIF /240 pxels 4CIF/D /480 pxels 2/3 D /480 pxels Default Clck Default to return the profle to the factory default values. Detals Clckng the Detals >> button dsplays further detals on mage qualty and data transmsson. These settngs requre extensve knowledge of the MPEG standard and vdeo data compresson. Incorrect settngs can render the vdeo mages unusable. Maxmum data rate Ths maxmum data rate s not exceeded under any crcumstances. Dependng on the vdeo qualty settngs for the I- and P-frames, ths fact can result n ndvdual mages beng skpped. The value entered here must be at least 10% hgher than the value entered n the Target data rate feld. If the value entered here s too low, t wll automatcally be adjusted. I-frame dstance Ths parameter allows you to set the ntervals n whch the I-frames wll be coded. 0 means auto mode, whereby the vdeo server nserts I-frames as necessary. An entry of 1 ndcates that I-frames are contnuously generated. An entry of 2 ndcates that only every second mage s an I-frame, and 3 only every thrd mage etc.; the frames n between are coded as P-frames. DOC V Installaton and Operatng Manual Bosch Securty Systems

49 VdeoJet X10 SN Confguraton Usng a Web Browser en 49 Vdeo qualty Ths settng allows you to adjust the mage qualty. The Auto opton automatcally adjusts to the optmum combnaton of movement and mage defnton (focus). Alternatvely, you can use the slde control to select a value between 1 and 100. A value of 100 results n a very hgh refresh rate and lower mage qualty. H.264 deblockng flter You can actvate a flter that reduces blockng n the mage n the case of H.264-encoded vdeo streams, thereby provdng a smoother mage. Please note that ths opton requres addtonal computng power. Prorty In the default confguraton None, the computng power provded for ndvdual tasks s negotated dynamcally. Ths ensures the best possble vdeo qualty at all tmes. Wth the MPEG-4/H.264 settng, vdeo transmssons are gven a hgher prorty and only a small amount of power remans avalable for JPEG mages. The JPEG settng s sutable for applcatons that prmarly requre JPEG mages, for example JPEG recordngs. When ths settng s made the amount of power avalable for vdeo mages wll be reduced Advanced Mode: Audo You can set the gan of the audo sgnals to sut your specfc requrements. The current vdeo mage s shown n the small wndow next to the slde controls to help you check the audo source and mprove assgnments. Your changes are effectve mmedately. If you connect va Web browser, you must actvate the audo transmsson on the LIVEPAGE Functons page (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). For other connectons, the transmsson depends on the audo settngs of the respectve system. Audo The audo sgnals are sent n a separate data stream parallel to the vdeo data, and so ncrease the network load. The audo data are encoded accordng to G.711 and requre an addtonal bandwdth of approx. 80 kbps for each connecton. If you do not want any audo data to be transmtted, select Off. Bosch Securty Systems Installaton and Operatng Manual DOC V

50 50 en Confguraton Usng a Web Browser VdeoJet X10 SN Lne In 1 You can set the lne nput gan. Make sure that the dsplay does not go beyond the green zone durng modulaton. Lne Out You can set the lne output gan. Make sure that the dsplay does not go beyond the green zone durng modulaton Advanced Mode: Storage Management You can record the mages from the camera connected to the VdeoJet X10 SN on varous local storage meda or on an approprately confgured SCSI system. CF cards (see Secton CF Slot, page 20) are the deal soluton for shorter storage tmes and temporary recordngs, for example alarm recordngs or local bufferng n the event of network nterruptons. f the VdeoJet X10 SN has a USB hard drve, ths s sutable for longer, local recordngs. For long-term, authortatve mages, t s essental that you use an approprately szed SCSI system. It s also possble to let the VRM Vdeo Recordng Manager control all recordng when accessng an SCSI system. Ths s an external program for confgurng recordng tasks for DOC V Installaton and Operatng Manual Bosch Securty Systems

51 VdeoJet X10 SN Confguraton Usng a Web Browser en 51 vdeo servers. For further nformaton please contact your local customer servce at Bosch Securty Systems. Devce manager If you actvate the VRM opton n ths screen, the VRM Vdeo Recordng Manager wll manage all recordng and you wll not be able to confgure any further settngs here.! CAUTION! Actvatng or deactvatng VRM causes the current settngs to be lost; they can only be restored through reconfguraton. Recordng meda Select the requred recordng meda here so that you can then actvate them and confgure the recordng parameters. SCSI Meda If you want to use an SCSI system as a recordng medum, you must set up a connecton to the requred SCSI system and set the confguraton parameters. The SCSI storage system selected must be avalable on the network and completely set up. Amongst other thngs, t must have an IP address and be dvded nto logcal drves (LUN). 1. Enter the IP address of the requred SCSI destnaton n the SCSI IP address feld. 2. If the SCSI destnaton s password protected, enter ths nto the Password feld. 3. Clck the Read button. The connecton to the IP address wll be establshed. In the Storage overvew feld, you can see the correspondng logcal drves. Local Meda The supported local recordng meda are dsplayed n the Storage overvew feld. If the local recordng medum s password protected, enter ths nto the Password feld. Actvatng and Confgurng Storage Meda The storage overvew dsplays the avalable storage meda. You can select ndvdual meda or SCSI drves and transfer these to the Managed storage meda lst. You can actvate the storage meda n ths lst and confgure them for storage.! CAUTION! Each storage medum can only be assocated wth one user. If a storage medum s already beng used by another user, you can decouple the user and connect the drve wth the VdeoJet X10 SN. Before decouplng, make absolutely sure that the prevous user no longer needs the storage medum. 1. In the Recordng meda secton, clck the SCSI Meda and Local Meda tabs to dsplay the applcable storage meda n the overvew. 2. In the Storage overvew secton, double-clck the requred storage medum, an SCSI LUN or one of the other avalable drves. The medum s then added to the Managed storage meda lst. In the Status column, newly added meda are ndcated by the status Not actve. 3. Clck the Set button to actvate all meda n the Managed storage meda lst. In the Status column, these are ndcated by the status Onlne. 4. Check the box n the Rec. 1 or Rec. 2 to specfy whch data stream should be recorded on the storage meda selected. Rec. 1 stores Stream 1, Rec. 2 stores Stream 2. Ths Bosch Securty Systems Installaton and Operatng Manual DOC V

52 52 en Confguraton Usng a Web Browser VdeoJet X10 SN means that you can record the standard data stream on a hard drve and record alarm mages on the moble CF card, for example. 5. Check the boxes for the Overwrte older recordngs opton to specfy whch older recordngs can be overwrtten once the avalable memory capacty has been used. Recordng 1 corresponds to Stream 1, Recordng 2 corresponds to Stream 2.! CAUTION! If older recordngs are not allowed to be overwrtten when the avalable memory capacty has been used, the recordng n queston wll be stopped. You can specfy lmtatons for overwrtng old recordngs by confgurng the retenton tme (see Secton 5.24 Advanced Mode: Retenton Tme, page 55). Formattng Storage Meda You can delete all recordngs on a storage medum at any tme.! CAUTION! Check the recordngs before deletng and back up mportant sequences on the computer's hard drve. 1. Clck a storage medum n the Managed storage meda lst to select t. 2. Clck the Edt button below the lst. A new wndow wll open. 3. Clck the Formattng button to delete all recordngs n the storage medum. 4. Clck OK to close the wndow. Deactvatng Storage Meda You can deactvate any storage medum from the Managed storage meda lst. It s then no longer used for recordngs. 1. Clck a storage medum n the Managed storage meda lst to select t. 2. Clck the Remove button below the lst. The storage medum s deactvated and removed from the lst Advanced Mode: Remote Vdeo Devce You can allow a remote vdeo devce to use the VdeoJet X10 SN storage meda. Ths means you can record vdeo mages from a camera that does not have ts own storage meda, for example. Once you have entered the IP address of the remote vdeo devce and saved t by pressng Set, the VdeoJet X10 SN s then dsplayed for selecton n the Storage Management for the remote vdeo devce. DOC V Installaton and Operatng Manual Bosch Securty Systems

53 VdeoJet X10 SN Confguraton Usng a Web Browser en 53 IP Address Enter the IP address for the remote vdeo devce. 1. If you do not know the IP address, clck the Network Scan button. The search for possble devces n the network s started. A small arrow s then dsplayed next to the IP Address feld. 2. Clck the arrow to dsplay the lst of devces detected. 3. Clck the requred devce n the lst to transfer ts IP address Advanced Mode: Recordng Profles You can defne up to ten dfferent recordng profles. You wll then use these recordng profles n the recordng scheduler, where they are lnked wth the ndvdual days and tmes (see Secton 5.25 Advanced Mode: Recordng Scheduler, page 56). You can change or add to the recordng profle descrpton on the tabs on the Recordng Scheduler page (see Secton Tme perods, page 57). 1. Clck one of the tabs to edt the correspondng profle. Bosch Securty Systems Installaton and Operatng Manual DOC V

54 54 en Confguraton Usng a Web Browser VdeoJet X10 SN 2. If necessary, clck the Default button to return all settngs to ther default values. 3. Clck the Copy Settngs button f you want to copy the currently vsble settngs to other profles. A new wndow wll open and you can select the profles n whch you want to copy the settngs. 4. For each profle, clck the Set button to save the settngs n the unt. Standard recordng Here you can select the mode for standard recordngs. If you select Contnuous, the recordng proceeds contnuously. If the maxmum memory capacty s reached, older recordngs wll automatcally be overwrtten. If you select the Prealarm opton, recordng wll only take place n the pre-alarm tme, durng the alarm and durng the set post-alarm tme. If you select Off, no automatc recordng takes place.! CAUTION! You can specfy lmtatons for overwrtng older recordngs n Contnuous mode by confgurng the retenton tme (see Secton 5.24 Advanced Mode: Retenton Tme, page 55). Standard profle From ths feld, you can select the encoder profle to be used for recordng (see Secton 5.19 Advanced Mode: Encoder Profle, page 46). The recordng profle can devate from the standard settng Actve profle and s only used durng an actve recordng. Pre-alarm tme You can select the requred pre-alarm tme from the lst feld. Post-alarm tme You can select the requred post-alarm tme from the lst feld. Post-alarm profle You can select the encoder profle to be used for recordng durng the post-alarm tme (see Secton 5.19 Advanced Mode: Encoder Profle, page 46). The Standard profle opton adopts the selecton at the top of the page. Alarm nput / Moton alarm / Vdeo loss alarm Here you can select the alarm sensor that s to trgger a recordng. The moton alarm s confgured and actvated on the VCA page (see Secton 5.31 Advanced Mode: VCA Event Trggered, page 68). The alarm nputs are confgured and actvated on the Alarm Inputs page (see Secton 5.35 Advanced Mode: Alarm Inputs, page 73). The numberng of the checkboxes for the alarm nputs corresponds to the labelng of the alarm nputs on the VdeoJet X10 SN. Vrtual alarm Here you can select the vrtual alarm sensors that are to trgger a recordng, va RCP+ commands or alarm scrpts, for example. DOC V Installaton and Operatng Manual Bosch Securty Systems

55 VdeoJet X10 SN Confguraton Usng a Web Browser en 55 For more nformaton, please see the Alarm Task Scrpt Language document and the RCP+ documentaton. These documents can be found on the product CD suppled. Recordng ncludes You can specfy whether, n addton to vdeo data, audo data and metadata (for example alarms, VCA data and seral data) should also be recorded. Includng metadata could make subsequent searches of recordngs easer but t requres addtonal memory capacty.! CAUTION! Wthout metadata, t s not possble to nclude vdeo content analyss n recordngs Advanced Mode: Retenton Tme You can specfy the retenton tmes for recordngs. If the avalable memory capacty of a medum has been used, older recordngs are only overwrtten f the retenton tme entered here has expred. Make sure that the retenton tme corresponds wth the avalable memory capacty. A rule of thumb for the memory requrement s as follows: 1 GB per hour retenton tme wth 4CIF for complete frame rate and hgh mage qualty. Retenton tme Camera 1 Enter the requred retenton tme n hours or days for each recordng. Recordng 1 corresponds to Stream 1, Recordng 2 corresponds to Stream 2. Bosch Securty Systems Installaton and Operatng Manual DOC V

56 56 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.25 Advanced Mode: Recordng Scheduler The recordng scheduler allows you to lnk the created recordng profles wth the days and tmes at whch the camera's mages are to be recorded n the event of an alarm. You can lnk any number of 15-mnute ntervals wth the recordng profles for each day of the week. Movng the mouse cursor over the table dsplays the tme below t. Ths ads orentaton. In addton to the normal weekdays, you can defne holdays that are not n the standard weekly schedule on whch recordngs are to apply. Ths allows you to apply a schedule for Sundays to other days wth dates that fall on varyng weekdays. 1. Clck the profle you want to lnk n the Tme perods feld. 2. Clck n a feld n the table, hold down the mouse button and drag the cursor over all the perods to be assgned to the selected profle. 3. Use the rght mouse button to deselect any of the ntervals. 4. Clck the Select All button to lnk all tme ntervals to the selected profle. 5. Clck the Clear All button to deselect all of the ntervals. 6. When you are fnshed, clck the Set button to save the settngs n the unt. DOC V Installaton and Operatng Manual Bosch Securty Systems

57 VdeoJet X10 SN Confguraton Usng a Web Browser en 57 Holdays You can defne holdays that are not n the standard weekly schedule on whch recordngs are to apply. Ths allows you to apply a schedule for Sundays to other days wth dates that fall on varyng weekdays. 1. Clck the Holdays tab. Any days that have already been selected wll be shown n the table. 2. Clck the Add button. A new wndow wll open. 3. Select the desred date from the calendar. You can select several consecutve calendar days by holdng down the mouse button. These wll later be dsplayed as a sngle entry n the table. 4. Clck OK to accept the selecton. The wndow wll close. 5. Assgn the ndvdual holdays to the recordng profles, as descrbed above. Deletng Holdays You can delete holdays you have defned yourself at any tme. 1. Clck the Delete button. A new wndow wll open. 2. Clck the date you wsh to delete. 3. Clck OK. The tem wll be deleted from the table and the wndow wll close. 4. The process must be repeated for deletng addtonal days. Tme perods You can change the names of the recordng profles. 1. Clck a profle and then the Rename button. 2. Enter your chosen name and then clck the Rename button agan. Actvatng the Recordng After completng confguraton you must actvate the recordng scheduler and start the recordng. Once recordng s underway, the Recordng Profles and Recordng Scheduler pages are deactvated and the confguraton cannot be modfed. You can stop the recordng actvty at any tme and modfy the settngs. 1. Clck the Start button to actvate the recordng scheduler. 2. Clck the Stop button to deactvate the recordng scheduler. Runnng recordngs are nterrupted and the confguraton can be changed. Recordng status The graphc ndcates the recordng actvty of the VdeoJet X10 SN. You wll see an anmated graphc whle recordng s takng place. Bosch Securty Systems Installaton and Operatng Manual DOC V

58 58 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.26 Advanced Mode: Recordng Status Certan detals on the recordng status are dsplayed here for nformaton purposes. You cannot change any of these settngs Advanced Mode: Alarm Connectons You can select how the VdeoJet X10 SN responds to an alarm. In the event of an alarm, the unt can automatcally connect to a pre-defned IP address. You can enter up to ten IP addresses to whch the VdeoJet X10 SN wll connect n sequence n the event of an alarm, untl a connecton s made. Connect on alarm Select On so that the VdeoJet X10 SN automatcally connects to a predefned IP address n the event of an alarm. DOC V Installaton and Operatng Manual Bosch Securty Systems

59 VdeoJet X10 SN Confguraton Usng a Web Browser en 59 By settng Follows nput 1 the unt mantans the connecton that has been automatcally establshed for as long as an alarm exsts on alarm nput 1. In the default settng, Stream 2 s transmtted for alarm connectons. Bear ths fact n mnd when assgnng the profle (see Secton 5.19 Advanced Mode: Encoder Profle, page 46). Number of destnaton IP address Specfy the numbers of the IP addresses to be contacted n the event of an alarm. The unt contacts the remote statons one after the other n the numbered sequence untl a connecton s made. Destnaton IP address For each number, enter the correspondng IP address for the desred remote staton. Destnaton password If the remote staton s password protected, enter the password here. In ths page, you can save a maxmum of ten destnaton IP addresses and hence up to ten passwords for connectng to remote statons. If connectons to more than ten remote statons are to be possble, for example when ntatng connectons va hgher-rankng systems such as VIDOS or Bosch Vdeo Management System, you can store a general password here. The VdeoJet X10 SN can use ths general password to connect to all remote statons protected wth the same password. In ths case, proceed as follows: 1. Select 10 from the Number of destnaton IP address lst feld. 2. Enter the address n the Destnaton IP address feld. 3. Enter your chosen password n the Destnaton password feld. 4. Defne ths password as the user password for all remote statons to whch a connecton s to be possble. If you enter the destnaton IP address for destnaton 10, ths VdeoJet X10 SN address wll no longer be used for the tenth attempt at automatc connecton n the event of an alarm. The parameter s then used only to save the general password. Vdeo transmsson If the unt s operated behnd a frewall, TCP (HTTP port) should be selected as the transfer protocol. For use n a local network, select UDP.! CAUTION! Please note that n some crcumstances, a larger bandwdth must be avalable on the network for addtonal vdeo mages n the event of an alarm, n case Multcast operaton s not possble. To enable Multcast operaton, select the UDP opton for the Vdeo transmsson parameter here and on the Network page (see Secton Vdeo transmsson, page 77). Remote port Dependng on the network confguraton, select a browser port here. The ports for HTTPS connectons wll be avalable only f the On opton s selected n the SSL encrypton parameter. Bosch Securty Systems Installaton and Operatng Manual DOC V

60 60 en Confguraton Usng a Web Browser VdeoJet X10 SN Vdeo output If you know whch unt s beng used as the recever, you can select the analog vdeo output to whch the sgnal should be swtched. If the destnaton unt s unknown, t s advsable to select the Frst avalable opton. In ths case, the mage s placed on the frst free vdeo output. Ths s an output on whch there s no sgnal. The connected montor only dsplays mages when an alarm s trggered. If you select a partcular vdeo output and a splt mage s set for ths output on the recever, you can also select from Decoder the decoder n the recever that s to be used to dsplay the alarm mage. Refer to the destnaton unt documentaton concernng mage dsplay optons and avalable vdeo outputs. Decoder Select a decoder of the recever to dsplay the alarm mage. The decoder selected has an mpact on the poston of the mage n a splt screen. For example, you can specfy va a VIP XD that the upper-rght quadrant should be used to dsplay the alarm mage by selectng decoder 2. SSL encrypton The data for the connecton, for example the password, can be securely transmtted wth SSL encrypton. If you have selected the On opton, only encrypted ports are offered n the Remote port parameter. Please note that the SSL encrypton must be actvated and confgured at both ends of a connecton. Ths requres the approprate certfcates to be uploaded onto the VdeoJet X10 SN (see Secton Mantenance log, page 85). You can actvate and confgure encrypton of the meda data (vdeo, audo and metadata) on the Encrypton page (see Secton 5.42 Advanced Mode: Encrypton, page 83). Auto-connect Select the On opton to automatcally re-establsh a connecton to one of the prevously specfed IP addresses after each reboot, after a connecton breakdown or after a network falure. In the default settng, Stream 2 s transmtted for automatc connectons. Bear ths fact n mnd when assgnng the profle (see Secton 5.19 Advanced Mode: Encoder Profle, page 46). Audo Select the On opton f you wsh to addtonally transmt a standalone G.711 encoded audo stream wth alarm connectons. DOC V Installaton and Operatng Manual Bosch Securty Systems

61 VdeoJet X10 SN Confguraton Usng a Web Browser en Advanced Mode: VCA The VdeoJet X10 SN contans an ntegrated vdeo content analyss (VCA), whch can detect and analyze changes n the sgnal on the bass of mage processng. Such changes can be due to movements n the camera's feld of vew. You can select varous VCA confguratons and adapt these to your applcaton as requred. The Slent MOTION+ confguraton s actve by default. In ths confguraton, metadata s created to facltate searches of recordngs; however, no alarm s trggered. 1. Select a VCA confguraton and make the requred settngs. 2. If necessary, clck the Default button to return all settngs to ther default values. Bosch Securty Systems Installaton and Operatng Manual DOC V

62 62 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.29 Advanced Mode: VCA Profles You can confgure two profles wth dfferent VCA confguratons. You can save profles on your computer's hard drve and load saved profles from there. Ths can be useful f you want to test a number of dfferent confguratons. Save a functonng confguraton and test new settngs. You can use the saved confguraton to restore the orgnal settngs at any tme. If computng power becomes short, the hghest prorty s always the lve mages and recordngs. Ths can lead to mparment of the vdeo content analyss. You should therefore observe the processor load and optmze the encoder settngs or the vdeo content analyss settngs as necessary (see Secton 8.6 Network Connecton, page 108). 1. Select a VCA profle and enter the requred settngs. 2. If necessary, clck the Default button to return all settngs to ther default values. DOC V Installaton and Operatng Manual Bosch Securty Systems

63 VdeoJet X10 SN Confguraton Usng a Web Browser en Clck the Save... button to save the profle settngs to another fle. A new wndow s opened, n whch you can specfy where you want to save the fle and what name you want to save t under. 4. Clck the Load... button to load a saved profle. A new wndow opens n whch you can select the profle fle and specfy where to save the fle. VCA confguraton Select one of the profles here to actvate t or edt t. You can rename the profle. 1. To rename the fle, clck the con to the rght of the lst feld and enter the new profle name n the feld. 2. Clck the con agan. The new profle name s saved. Alarm status The alarm status s dsplayed here for nformaton purposes. Ths means you can check the effects of your settngs mmedately. Analyss type Select the requred analyss algorthm. By default, only MOTION+ s avalable ths offers a moton detector and essental recognton of tamperng. Addtonal analyss algorthms wth comprehensve functons such as IVMD and IVA are avalable from Bosch Securty Systems. If you select one of these algorthms, you can set the correspondng parameters here drectly. You can fnd nformaton on ths n the relevant documents on the product CD suppled. Metadata s always created for a vdeo content analyss, unless ths was explctly excluded. Dependng on the analyss type selected and the relevant confguraton, addtonal nformaton overlays the vdeo mage n the prevew wndow next to the parameter settngs. Wth the MOTION+ analyss type, for example, the sensor felds n whch moton s recorded wll be marked wth rectangles. On the LIVEPAGE Functons page, you can also enable addtonal nformaton overlays for the LIVEPAGE (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). Moton detector (MOTION+ only) For the detector to functon, the followng condtons must be met: Analyss must be actvated. At least one sensor feld must be actvated. The ndvdual parameters must be confgured to sut the operatng envronment and the desred responses. The senstvty must be set to a value greater than zero.! CAUTION! Reflectons of lght (off glass surfaces, etc.), swtchng lghts on or off or changes n the lght level caused by cloud movement on a sunny day can trgger unntended responses from the moton detector and generate false alarms. Run a seres of tests at dfferent tmes of the day and nght to ensure that the vdeo sensor s operatng as ntended. For ndoor survellance, ensure constant lghtng of the areas durng the day and at nght. Bosch Securty Systems Installaton and Operatng Manual DOC V

64 64 en Confguraton Usng a Web Browser VdeoJet X10 SN Senstvty (MOTION+ only) The basc senstvty of the moton detector can be adjusted for the envronmental condtons to whch the camera s subject. The sensor reacts to varatons n the brghtness of the vdeo mage. The darker the observaton area, the hgher the value that must be selected. Mnmum object sze (MOTION+ only) You can specfy the number of sensor felds that a movng object must cover to generate an alarm. Ths s to prevent objects that are too small from trggerng an alarm. A mnmum value of 4 s recommended. Ths value corresponds to four sensor felds. Select Area (MOTION+ only) The areas of the mage to be montored by the moton detector can be selected. The vdeo mage s subdvded nto 858 square felds. Each of these felds can be actvated or deactvated ndvdually. If you wsh to exclude partcular regons of the camera's feld of vew from montorng due to contnuous movement (by a tree n the wnd, etc.), the relevant felds can be deactvated. 1. Clck Select Area to confgure the sensor felds. A new wndow wll open. 2. If necessary, clck Clear All frst to clear the current selecton (felds marked yellow). 3. Left-clck the felds to be actvated. Actvated felds are marked yellow. 4. If necessary, clck Select All to select the entre vdeo frame for montorng. 5. Rght-clck any felds you wsh to deactvate. 6. Clck OK to save the confguraton. 7. Clck the close button X n the wndow ttle bar to close the wndow wthout savng the changes. Tamper detecton You can reveal the tamperng of cameras and vdeo cables by means of varous optons. Run a seres of tests at dfferent tmes of the day and nght to ensure that the vdeo sensor s operatng as ntended. The optons for tamper detecton can only be set for fxed cameras. Dome cameras or other motorzed cameras cannot be protected n ths manner as the movement of the camera tself causes changes n the vdeo mage that are too great. Senstvty Ths and the followng parameter are only accessble f the reference check s actvated. The basc senstvty of the tamper detecton can be adjusted for the envronmental condtons to whch the camera s subject. The algorthm reacts to the dfferences between the reference mage and the current vdeo mage. The darker the observaton area, the hgher the value that must be selected. Trgger delay (s) You can set delayed alarm trggerng. The alarm s only trggered after a set tme nterval n seconds has elapsed and then only f the trggerng condton stll exsts. If the orgnal condton has been restored before ths tme nterval elapses, the alarm s not trggered. Ths allows you to avod false alarms trggered by short-term changes, for example cleanng actvtes n the drect feld of vson of the camera. DOC V Installaton and Operatng Manual Bosch Securty Systems

65 VdeoJet X10 SN Confguraton Usng a Web Browser en 65 Global change You can set how large the global change n the vdeo mage must be for an alarm to be trggered. Ths settng s ndependent of the sensor felds selected under Select Area. Set a hgh value f fewer sensor felds need to change to trgger an alarm. Wth a low value, t s necessary for changes to occur smultaneously n a large number of sensor felds to trgger an alarm. Ths opton allows you to detect, ndependently of moton alarms, manpulaton of the orentaton or locaton of a camera resultng from turnng the camera mount bracket, for nstance. Global change Actvate ths functon f the global change, as set wth the Global change slde control, should trgger an alarm. Scene too brght Actvate ths functon f tamperng assocated wth exposure to extreme lght (for nstance, shnng a flashlght drectly on the lens) should trgger an alarm. The average brghtness of the scene provdes a bass for recognton. Scene too dark Actvate ths functon f tamperng assocated wth coverng the lens (for nstance, by sprayng pant on t) should trgger an alarm. The average brghtness of the scene provdes a bass for recognton. Scene too nosy Actvate ths functon f tamperng assocated wth EMC nterference (nosy scene as the result of a strong nterference sgnal n the vcnty of the vdeo lnes), as an example, should trgger an alarm. Reference check You can save a reference mage that s contnuously compared wth the current vdeo mage. If the current vdeo mage n the marked areas dffers from the reference mage, an alarm s trggered. Ths allows you to detect tamperng that would otherwse not be detected, for example f the camera s turned. 1. Clck Reference to save the currently vsble vdeo mage as a reference. 2. Clck Select Area and select the areas n the reference mage that are to be montored. 3. Check the box Reference check to actvate on-gong matchng. The stored reference mage s dsplayed n black and whte below the current vdeo mage, and the selected areas are marked n yellow. 4. Select the Dsappearng edges or Appearng edges opton to specfy the reference check once agan. Select Area You can select the mage areas n the reference mage that are to be montored. The vdeo mage s subdvded nto 858 square felds. Each of these felds can be actvated or deactvated ndvdually. Select only those areas for reference montorng n whch no movement takes place and that are always evenly lt, as false alarms could otherwse be trggered. 1. Clck Select Area to confgure the sensor felds. A new wndow wll open. 2. If necessary, clck Clear All frst to clear the current selecton (felds marked yellow). Bosch Securty Systems Installaton and Operatng Manual DOC V

66 66 en Confguraton Usng a Web Browser VdeoJet X10 SN 3. Left-clck the felds to be actvated. Actvated felds are marked yellow. 4. If necessary, clck Select All to select the entre vdeo frame for montorng. 5. Rght-clck any felds you wsh to deactvate. 6. Clck OK to save the confguraton. 7. Clck the close button X n the wndow ttle bar to close the wndow wthout savng the changes Advanced Mode: VCA Scheduled Ths confguraton allows you to lnk the created VCA profle wth the days and tmes at whch the vdeo content analyss s to be actve. You can lnk any number of 15-mnute ntervals wth the VCA profles for each day of the week. Movng the mouse cursor over the table dsplays the tme below t. Ths ads orentaton. In addton to the normal weekdays, you can defne holdays that are not n the standard weekly schedule on whch recordngs are to apply. Ths allows you to apply a schedule for Sundays to other days wth dates that fall on varyng weekdays. DOC V Installaton and Operatng Manual Bosch Securty Systems

67 VdeoJet X10 SN Confguraton Usng a Web Browser en Clck the profle you want to lnk n the Tme perods feld. 2. Clck n a feld n the table, hold down the mouse button and drag the cursor over all the perods to be assgned to the selected profle. 3. Use the rght mouse button to deselect any of the ntervals. 4. Clck the Select All button to lnk all tme ntervals to the selected profle. 5. Clck the Clear All button to deselect all of the ntervals. 6. When you are fnshed, clck the Set button to save the settngs n the unt. Holdays You can defne holdays on whch a profle should be actve that are dfferent to the standard weekly schedule. Ths allows you to apply a schedule for Sundays to other days wth dates that fall on varyng weekdays. 1. Clck the Holdays tab. Any days that have already been selected wll be shown n the table. 2. Clck the Add button. A new wndow wll open. 3. Select the desred date from the calendar. You can select several consecutve calendar days by holdng down the mouse button. These wll later be dsplayed as a sngle entry n the table. 4. Clck OK to accept the selecton. The wndow wll close. 5. Assgn the ndvdual holdays to the VCA profles, as descrbed above. Deletng Holdays You can delete holdays you have defned yourself at any tme. 1. Clck the Delete button. A new wndow wll open. 2. Clck the date you wsh to delete. 3. Clck OK. The tem wll be deleted from the table and the wndow wll close. 4. The process must be repeated for deletng addtonal days. Bosch Securty Systems Installaton and Operatng Manual DOC V

68 68 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.31 Advanced Mode: VCA Event Trggered Ths confguraton allows you stpulate that the vdeo content analyss s only to be actvated when trggered by an event. As long as no trgger s actvated, the Slent MOTION+ confguraton n whch metadata s created s actve; ths metadata facltates searches of recordngs, but does not trgger an alarm. Trgger You can select one of the physcal alarms on the devce's alarm nputs or one of the vrtual alarms as a trgger. A vrtual alarm s created usng software, wth RCP+ commands or alarm scrpts, for example. For more nformaton, please see the Alarm Task Scrpt Language document and the RCP+ documentaton. You can fnd these documents on the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). DOC V Installaton and Operatng Manual Bosch Securty Systems

69 VdeoJet X10 SN Confguraton Usng a Web Browser en 69 Trgger actve Select the VCA confguraton here that s to be enabled va an actve trgger. A green check mark to the rght of the lst feld ndcates that the trgger s actve. Trgger nactve Select the VCA confguraton here that s to be actvated f the trgger s not actve. A green check mark to the rght of the lst feld ndcates that the trgger s nactve. Delay (s) Select the delay perod here for the reacton of the vdeo content analyss to trgger sgnals. A delay perod may be useful n avodng false alarms or frequent trggerng, for example. Durng the delay perod, the Slent MOTION+ confguraton s always enabled Advanced Mode: Audo Alarm The VdeoJet X10 SN can create alarms on the bass of audo sgnals. You can confgure sgnal strengths and frequency ranges n such a way that false alarms, for example due to machne nose or background nose, are avoded. Frst set up normal audo transmsson before you confgure the audo alarm here (see Secton 5.20 Advanced Mode: Audo, page 49). Audo alarm Select On f you want the devce to generate audo alarms. Bosch Securty Systems Installaton and Operatng Manual DOC V

70 70 en Confguraton Usng a Web Browser VdeoJet X10 SN Name The name makes t easer to dentfy the alarm n extensve vdeo montorng systems, for example wth the VIDOS and Bosch Vdeo Management System programs. Enter a unque and clear name here.! CAUTION! Do not use any specal characters, for example &, n the name. Specal characters are not supported by the system's nternal recordng management and may therefore result n the Player or Archve Player beng unable to play back the recordng. Threshold Set up the threshold on the bass of the sgnal vsble n the graphc You can set the threshold usng the slde control or, alternatvely, you can move the whte lne drectly n the graphc usng the mouse. Senstvty You can use ths settng to adapt the senstvty to the sound envronment. You can effectvely suppress ndvdual sgnal peaks. A hgh value represents a hgh level of senstvty. Sgnal Ranges You can exclude partcular sgnal ranges n order to avod false alarms. For ths reason the total sgnal s dvded nto 13 tonal ranges (mel scale). Check or uncheck the boxes below the graphc to nclude or exclude ndvdual ranges Advanced Mode: Alarm E-Mal As an alternatve to automatc connectng, alarm states can also be documented by e-mal. In ths way t s possble to notfy a recpent who does not have a vdeo recever. In ths case, the VdeoJet X10 SN automatcally sends an e-mal to a prevously defned e-mal address. Send alarm e-mal Select On f you want the unt to automatcally send an alarm e-mal n the event of an alarm. DOC V Installaton and Operatng Manual Bosch Securty Systems

71 VdeoJet X10 SN Confguraton Usng a Web Browser en 71 Mal server IP address Enter the IP address of a mal server that operates on the SMTP standard (Smple Mal Transfer Protocol). Outgong e-mals are sent to the mal server va the address you entered. Otherwse leave the box blank ( ). SMTP user name Enter a regstered user name for the chosen malserver here. SMTP password Enter the requred password for the regstered user name here. Format You can select the data format of the alarm message. Standard (wth JPEG) E-mal wth attached JPEG mage fle. SMS E-mal n SMS format to an e-mal-to-sms gateway (for example to send an alarm by cellphone) wthout an mage attachment.! CAUTION! When a cellphone s used as the recever, make sure to actvate the e-mal or SMS functon, dependng on the format, so that these messages can be receved. You can obtan nformaton on operatng your cellphone from your cellphone provder. Attach JPEG from camera Clck the checkbox to specfy that JPEG mages are sent from the camera. An enabled vdeo nput s ndcated by a check mark. Destnaton address Enter the e-mal address for alarm e-mals here. The maxmum address length s 49 characters. Sender name Enter a unque name for the e-mal sender, for example the locaton of the unt. Ths wll make t easer to dentfy the orgn of the e-mal. Test e-mal You can test the e-mal functon by clckng the Send Now button. An alarm e-mal s mmedately created and sent. Bosch Securty Systems Installaton and Operatng Manual DOC V

72 72 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.34 Advanced Mode: Alarm Task Edtor! CAUTION! Edtng scrpts on ths page overwrtes all settngs and entres on the other alarm pages. Ths procedure cannot be reversed. In order to edt ths page, you must have programmng knowledge and be famlar wth the nformaton n the Alarm Task Scrpt Language document. You can fnd the document on the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). As an alternatve to the alarm settngs on the varous alarm pages, you can enter your desred alarm functons n scrpt form here. Ths wll overwrte all settngs and entres on the other alarm pages. 1. Clck the Examples lnk under the Alarm Task Edtor feld to see some scrpt examples. A new wndow wll open. 2. Enter new scrpts n the Alarm Task Edtor feld or change exstng scrpts n lne wth your requrements. 3. When you are fnshed, clck the Set button to transmt the scrpts to the unt. If the transfer was successful, the message Scrpt successfully parsed s dsplayed over the text feld. If t was not successful, an error message wll be dsplayed wth further nformaton. DOC V Installaton and Operatng Manual Bosch Securty Systems

73 VdeoJet X10 SN Confguraton Usng a Web Browser en Advanced Mode: Alarm Inputs You can confgure the alarm nputs of the VdeoJet X10 SN. Alarm nput Select Actve hgh f the alarm s to be trggered when the contact closes. Select Actve low f the alarm s to be trggered when the contact opens. Name You can enter a name for each alarm nput, whch s then dsplayed below the con for the alarm nput on the LIVEPAGE f confgured correctly (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42) Advanced Mode: Relay You can confgure the swtchng behavor of the relay outputs. For each relay, you can specfy an open swtch relay (normally closed contact) or a closed swtch relay (normally open contact). You can also specfy whether an output should operate as a bstable or monostable relay. In bstable mode, the trggered state of the relay s mantaned. In monostable mode, you can set the tme after whch the relay wll return to the dle state. You can select dfferent events that automatcally actvate an output. It s possble, for example, to turn on a floodlght by trggerng a moton alarm and then turnng the lght off agan when the alarm has stopped. Idle state Select Open f you want the relay to operate as an NO contact, or select Closed f the relay s to operate as an NC contact. Bosch Securty Systems Installaton and Operatng Manual DOC V

74 74 en Confguraton Usng a Web Browser VdeoJet X10 SN Operatng mode Select an operatng mode for the relay. For example, f you want an alarm-actvated lamp to stay on after the alarm ends, select Bstable. If you wsh an alarm-actvated sren to sound for ten seconds, for example, select 10 s. Relay follows If requred, select a specfc event that wll trgger the relay. The followng events are possble trggers: Off Relay s not trggered by events Connecton Trgger whenever a connecton s made Vdeo alarm Trgger by nterrupton of the vdeo sgnal Moton alarm Trgger by moton alarm, as confgured on the VCA page (see Secton 5.31 Advanced Mode: VCA Event Trggered, page 68) Local nput Trgger by the correspondng external alarm nput Remote nput Trgger by remote staton's correspondng swtchng contact (only f a connecton exsts) The numbers n the lsts of selectable events relate to the correspondng connectons on the unt, Vdeo alarm 1, for example to the Vdeo In connecton. Relay name You can assgn a name for the relay here. The name s shown on the button next to Trgger relay. The Lvepage can also be confgured to dsplay the name under the relay con. Trgger relay Clck the button to trgger the relay manually (for testng or to operate a door opener, for example). DOC V Installaton and Operatng Manual Bosch Securty Systems

75 VdeoJet X10 SN Confguraton Usng a Web Browser en Advanced Mode: COM1 You can confgure the seral nterface parameters (orange termnal block) to meet your requrements. If the VdeoJet X10 SN s workng n multcast mode (see Secton 5.40 Advanced Mode: Multcastng, page 81), the frst remote locaton to establsh a vdeo connecton to the unt s also assgned the transparent data connecton. However, after about 15 seconds of nactvty the data connecton s automatcally termnated and another remote locaton can exchange transparent data wth the unt. Seral port functon Select a controllable unt from the lst. If you wsh to use the seral port to transmt transparent data, select Transparent. Select Termnal f you wsh to operate the unt from a termnal. After selectng a unt, the remanng parameters n the wndow are set automatcally and should not be changed. Camera ID If necessary, enter the ID of the perpheral you wsh to control (for example a dome camera or pan/tlt head). Baud rate Select the value for the transmsson rate n bps. Data bts The number of data bts per character cannot be changed. Stop bts Select the number of stop bts per character. Party check Select the type of party check. Interface mode Select the desred protocol for the seral nterface. Bosch Securty Systems Installaton and Operatng Manual DOC V

76 76 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.38 Advanced Mode: Network The settngs on ths page are used to ntegrate the VdeoJet X10 SN nto an exstng network. Some changes only take effect after the unt s rebooted. In ths case, the Set button changes to Set and Reboot. 1. Make the desred changes. 2. Clck the Set and Reboot button. The VdeoJet X10 SN s rebooted and the changed settngs are actvated. DOC V Installaton and Operatng Manual Bosch Securty Systems

77 VdeoJet X10 SN Confguraton Usng a Web Browser en 77! CAUTION! If you change the IP address, subnet mask or gateway address, the VdeoJet X10 SN s only avalable under the new addresses after the reboot. Automatc IP assgnment If a DHCP server s employed n the network for the dynamc assgnment of IP addresses, you can actvate acceptance of IP addresses automatcally assgned to the VdeoJet X10 SN. Certan applcatons (VIDOS, Bosch Vdeo Management System, Archve Player, Confguraton Manager) use the IP address for the unque assgnment of the unt. If you use these applcatons, the DHCP server must support the fxed assgnment between IP address and MAC address, and must be approprately set up so that, once an IP address s assgned, t s retaned each tme the system s rebooted. IP address Enter the desred IP address for the VdeoJet X10 SN n ths feld. The IP address must be vald for the network. Subnet mask Enter the approprate subnet mask for the selected IP address here. Gateway address If you want the unt to establsh a connecton to a remote locaton n a dfferent subnet, enter the IP address of the gateway here. Otherwse leave the box blank ( ). DNS server address The unt can use a DNS server to trgger an address specfed as a name. Enter the IP address of the DNS server here. Vdeo transmsson If the unt s operated behnd a frewall, TCP (HTTP port) should be selected as the transfer protocol. For use n a local network, select UDP.! CAUTION! Multcast operaton s only possble wth the UDP protocol. The TCP protocol does not support multcast connectons. The MTU value n UDP mode s 1,514 bytes. HTTP browser port Select a dfferent HTTP browser port from the lst f requred. The default HTTP port s 80. If you want to allow only secure connectons va HTTPS, you must deactvate the HTTP port. In ths case, select Off. HTTPS browser port If you wsh to allow browser access on the network va a secure connecton, select an HTTPS browser port from the lst f necessary. The default HTTPS port s 443. Select the Off opton to deactvate HTTPS ports; only unsecured connectons wll now be possble. The VdeoJet X10 SN uses the TLS 1.0 encrypton protocol. You may have to actvate ths protocol va your browser confguraton. You must also actvate the protocol for the Java applcatons (va the Java control panel n the Wndows control panel). Bosch Securty Systems Installaton and Operatng Manual DOC V

78 78 en Confguraton Usng a Web Browser VdeoJet X10 SN If you want to allow only secure connectons wth SSL encrypton, you must select the Off opton for each of the parameters HTTP browser port, RCP+ port 1756 and Telnet support. Ths deactvates all unsecured connectons. Connectons wll then only be possble va the HTTPS port. You can actvate and confgure encrypton of the meda data (vdeo, audo and metadata) on the Encrypton page (see Secton 5.42 Advanced Mode: Encrypton, page 83). RCP+ port 1756 To exchange connecton data, you can actvate the unsecured RCP+ port If you want connecton data to be transmtted only when encrypted, select the Off opton to deactvate the port. Telnet support If you want to allow only secure connectons wth encrypted data transmsson, you must select the Off opton to deactvate Telnet support. The unt wll then no longer be accessble usng the Telnet protocol. Interface mode ETH If necessary, select the Ethernet lnk type for the ETH nterface. Dependng on the unt connected, t may be necessary to select a specal operaton type. Network MSS (Byte) You can set the maxmum segment sze for the IP packet's user data. Ths gves you the opton to adjust the sze of the data packets to the network envronment and to optmze data transmsson. Please comply wth the MTU value of 1,514 bytes n UDP mode. SCSI MSS (Byte) You can specfy a hgher MSS value for a connecton to the SCSI system than for the other data traffc va the network. The potental value depends on the network structure. A hgher value s only useful f the SCSI system s located n the same subnet as the VdeoJet X10 SN. Enable DynDNS DynDNS.org s a DNS hostng servce that stores IP addresses n a database ready for use. It allows you to select the VdeoJet X10 SN va the Internet usng a host name, wthout havng to know the current IP address of the unt. You can enable ths servce here. To do ths, you must have an account wth DynDNS.org and you must have regstered the requred host name for the unt on that ste. Informaton about the servce, regstraton process and avalable host names can be found at DynDNS.org. Host name Enter the host name regstered on DynDNS.org for the VdeoJet X10 SN here. User name Enter the user name you regstered at DynDNS.org here. Password Enter the password you regstered at DynDNS.org here. DOC V Installaton and Operatng Manual Bosch Securty Systems

79 VdeoJet X10 SN Confguraton Usng a Web Browser en 79 Force regstraton now You can force the regstraton by transferrng the IP address to the DynDNS server. Entres that change frequently are not provded n the Doman Name System. It s a good dea to force the regstraton when you are settng up the devce for the frst tme. Only use ths functon when necessary and no more than once a day, to avod the possblty of beng blocked by the servce provder. To transfer the IP address of the VdeoJet X10 SN, clck the Regster button. Status The status of the DynDNS functon s dsplayed here for nformaton purposes. You cannot change any of these settngs Advanced Mode: Advanced The settngs on ths page are used to mplement advanced settngs for the network. Some changes only take effect after the unt s rebooted. In ths case, the Set button changes to Set and Reboot. 1. Make the desred changes. 2. Clck the Set and Reboot button. The VdeoJet X10 SN s rebooted and the changed settngs are actvated. Bosch Securty Systems Installaton and Operatng Manual DOC V

80 80 en Confguraton Usng a Web Browser VdeoJet X10 SN SNMP The VdeoJet X10 SN supports the SNMP V2 (Smple Network Management Protocol) for managng and montorng network components, and can send SNMP messages (traps) to IP addresses. The unt supports SNMP MIB II n the unfed code. If you wsh to send SNMP traps, enter the IP addresses of one or two requred target devces here. If you select On for the SNMP parameter and do not enter an SNMP host address, the VdeoJet X10 SN does not send them automatcally, but only reples to SNMP requests. If you enter one or two SNMP host addresses, SNMP traps are sent automatcally. Select Off to deactvate the SNMP functon. 1. SNMP host address / 2. SNMP host address If you wsh to send SNMP traps automatcally, enter the IP addresses of one or two requred target unts here. SNMP traps You can select whch traps are to be sent. 1. Clck Select. A lst s opened. 2. Clck the checkboxes to select the requred traps. All the checked traps wll be sent. 3. Clck Set to accept the selecton. Authentcaton If a RADIUS server s employed n the network for managng access rghts, authentcaton must be actvated here to allow communcaton wth the unt. The RADIUS server must also contan the correspondng data. To confgure the unt, you must connect the VdeoJet X10 SN drectly to a computer usng a network cable. Ths s because communcaton va the network s not enabled untl the Identty and Password parameters have been set and successfully authentcated. Identty Enter the name that the RADIUS server s to use for dentfyng the VdeoJet X10 SN. Password Enter the password that s stored n the RADIUS server. RTSP port If necessary, select a dfferent port for the exchange of the RTSP data from the lst. The standard RTSP port s 554. Select Off to deactvate the RTSP functon. DOC V Installaton and Operatng Manual Bosch Securty Systems

81 VdeoJet X10 SN Confguraton Usng a Web Browser en Advanced Mode: Multcastng In addton to a 1:1 connecton between an encoder and a sngle recever (uncast), the VdeoJet X10 SN can enable multple recevers to receve the vdeo sgnal from an encoder smultaneously. The devce ether duplcates the data stream tself and then dstrbutes t to multple recevers (Mult-uncast) or t sends a sngle data stream to the network, where the data stream s smultaneously dstrbuted to multple recevers n a defned group (Multcast). You can enter a dedcated multcast address and port for each stream. You can swtch between the streams by clckng the approprate tabs. Multcast operaton requres a multcast-enabled network that uses the UDP and the Internet Group Management IGMP protocols. Other group management protocols are not supported. The TCP protocol does not support multcast connectons. A specal IP address (class D address) must be confgured for multcast operaton n a multcast-enabled network. The network must support group IP addresses and the Internet Group Management Protocol (IGMP V2). The address range s from to The multcast address can be the same for multple streams. However, t wll be necessary to use a dfferent port n each case so that multple data streams are not sent smultaneously usng the same port and multcast address. The settngs must be made ndvdually for each stream. Enable To enable smultaneous data recepton on several recevers you need to actvate the multcast functon. To do ths, check the box. You can then enter the multcast address. Multcast Address Enter a vald multcast address for each stream to be operated n multcast mode (duplcaton of the data streams n the network). Wth the settng the encoder for the relevant stream operates n mult-uncast mode (copyng of data streams n the unt). The VdeoJet X10 SN supports mult-uncast connectons for up to fve smultaneously connected recevers. Bosch Securty Systems Installaton and Operatng Manual DOC V

82 82 en Confguraton Usng a Web Browser VdeoJet X10 SN Duplcaton of data places a heavy demand on the unt and can lead to mparment of the mage qualty under certan crcumstances. Port Assgn a dfferent port to each data stream f there are smultaneous data streams at the same multcast address. Enter the port address of the requred stream here. Streamng Clck the checkbox to actvate multcast streamng mode for the relevant stream. An enabled stream s ndcated by a check mark. For normal multcast operaton, streamng s typcally not requred. Multcast packet TTL You can enter a value to specfy how long the multcast data packets are actve on the network. Ths value must be greater than one f multcast s to be run va a router Advanced Mode: JPEG Postng You can save ndvdual JPEG mages on an FTP server at specfc ntervals. You can then retreve these mages at a later date to reconstruct alarm events f requred. Image sze Select the resoluton you wsh the JPEG mages to have: Small /120 pxels (QCIF) Medum /240 pxels (CIF) Large /480 pxels (4CIF) DOC V Installaton and Operatng Manual Bosch Securty Systems

83 VdeoJet X10 SN Confguraton Usng a Web Browser en 83 Fle name You can select how fle names wll be created for the ndvdual mages that are transmtted. Overwrte The same fle name s always used and any exstng fle wll be overwrtten wth the current fle. Increment A number from 000 to 255 s added to the fle name and automatcally ncremented by 1. When t reaches 255 t starts agan from 000. Date/tme suffx The date and tme are automatcally added to the fle name. When settng ths parameter, ensure that the unt's date and tme are always correctly set. Example: the fle snap011005_ jpg was stored on October 1, 2005 at 11:45 and 30 seconds. Postng nterval Enter the nterval n seconds at whch the mages wll be sent to an FTP server. Enter zero f you do not want any mages to be sent. FTP server IP address Enter the IP address of the FTP server on whch you wsh to save the JPEG mages. FTP server logn Enter your logn name for the FTP server. FTP server password Enter the password that gves you access to the FTP server. Path on FTP server Enter the exact path on whch you wsh to post the mages on the FTP server. The creaton of JPEG mages has a lower prorty than vdeo encodng and mage analyss. Thscan result n JPEG mages beng created wth a delay of up to several seconds after the trggerng event. If relable, real-tme recordng of the alarm s requred, ensure that the encoder has enough computng power avalable Advanced Mode: Encrypton A specal lcense, wth whch you wll receve a correspondng actvaton key, s requred to encrypt user data. You can enter the actvaton key to release the functon on the Lcenses page (see Secton 5.44 Advanced Mode: Lcenses, page 86). Bosch Securty Systems Installaton and Operatng Manual DOC V

84 84 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.43 Advanced Mode: Mantenance Frmware The VdeoJet X10 SN s desgned n such a way that ts functons and parameters can be updated wth frmware. To do ths, transfer the current frmware package to the unt va the selected network. It wll then be automatcally nstalled there. In ths way, a VdeoJet X10 SN can be servced and updated remotely wthout a techncan havng to change the nstallaton on ste. You obtan the current frmware from your customer servce or from the download area at CAUTION! Before launchng the frmware upload make sure that you have selected the correct upload fle. Uploadng the wrong fles can result n the unt no longer beng addressable, n whch case you must replace the unt. You should never nterrupt the nstallaton of frmware. An nterrupton can lead to the flash- EPROM beng ncorrectly programmed. Ths n turn can result n the unt no longer beng addressable, n whch case t wll have to be replaced. Even changng to another page or closng the browser wndow leads to an nterrupton. 1. Frst store the frmware fle on your hard drve. 2. Enter the full path of the frmware fle n the feld or clck Browse to locate and select the fle. 3. Next, clck Upload to begn transferrng the fle to the unt. The progress bar allows you to montor the transfer. The new frmware s unpacked and the Flash EPROM s reprogrammed. The tme remanng s shown by the message gong to reset Reconnectng n... seconds. The unt reboots automatcally once the upload has successfully completed. If the Connect LED lghts up red, the upload has faled and must be repeated. To perform the upload you must now swtch to a specal page: 1. In the address bar of your browser, enter /man.htm after the IP address of the VdeoJet X10 SN (for example /man.htm). 2. Repeat the upload. Confguraton You can save confguraton data for the VdeoJet X10 SN on a computer and then load saved confguraton data from a computer to the unt. DOC V Installaton and Operatng Manual Bosch Securty Systems

85 VdeoJet X10 SN Confguraton Usng a Web Browser en 85 Upload 1. Enter the full path of the fle to upload or clck Browse to select the requred fle. 2. Make certan that the fle to be loaded comes from the same unt type as the unt you want to confgure. 3. Next, clck Upload to begn transferrng the fle to the unt. The progress bar allows you to montor the transfer. Once the upload s complete, the new confguraton s actvated. The tme remanng s shown by the message gong to reset Reconnectng n... seconds. The unt reboots automatcally once the upload has successfully completed. Download 1. Clck the Download button. A dalog box opens. 2. Follow the on-screen nstructons to save the current settngs. SSL certfcate To be able to work wth an SSL encrypted data connecton, both ends of a connecton must hold the relevant certfcates. You can upload the SSL certfcate, comprsng one or multple fles, onto the VdeoJet X10 SN. If you wsh to upload multple fles onto the VdeoJet X10 SN, you must select them consecutvely. The certfcate must be created n the format *.pem so that t can be accepted by the unt. 1. Enter the full path of the fle to upload or clck Browse to select the requred fle. 2. Next, clck Upload to begn transferrng the fle to the unt. 3. Once all fles have been successfully uploaded, the unt must be rebooted. In the address bar of your browser, enter /reset after the IP address of the VdeoJet X10 SN (for example /reset). The new SSL certfcate s vald. Mantenance log You can download an nternal mantenance log from the unt to send t to Customer Servce for support purposes. Clck Download and select a storage locaton for the fle. Bosch Securty Systems Installaton and Operatng Manual DOC V

86 86 en Confguraton Usng a Web Browser VdeoJet X10 SN 5.44 Advanced Mode: Lcenses You can enter the actvaton key to release addtonal functons or software modules. The actvaton key cannot be deactvated agan and s not transferable to other unts Advanced Mode: System Overvew The data on ths page are for nformaton purposes only and cannot be changed. Keep a record of ths nformaton n case techncal assstance s requred. You can select all requred text on ths page wth the mouse and copy t to the clpboard wth the [Ctrl]+[C] key combnaton, for example f you want to send t va e-mal. DOC V Installaton and Operatng Manual Bosch Securty Systems

87 VdeoJet X10 SN Confguraton Usng a Web Browser en Functon Test The VdeoJet X10 SN offers a varety of confguraton optons. You should therefore check that t s functonng correctly after nstallaton and confguraton. The functon test s the only way to ensure that the VdeoJet X10 SN operates as expected n the event of an alarm. Your check should nclude the followng functons: Can the VdeoJet X10 SN be called up remotely? Does the VdeoJet X10 SN transmt all the requred data? Does the VdeoJet X10 SN respond to alarm events as requred? Do the recordngs occur as ntended? Is t possble to control perpherals f necessary? Bosch Securty Systems Installaton and Operatng Manual DOC V

88 88 en Confguraton Usng a Web Browser VdeoJet X10 SN DOC V Installaton and Operatng Manual Bosch Securty Systems

89 VdeoJet X10 SN Operaton en 89 6 Operaton 6.1 Operaton wth Mcrosoft Internet Explorer A computer wth Mcrosoft Internet Explorer (verson 6.0 or hgher) can receve lve mages from the VdeoJet X10 SN, control cameras or other perpherals and replay stored vdeo sequences. System Requrements Computer wth Wndows XP or Wndows Vsta operatng system Network access (Intranet or Internet) Mcrosoft Internet Explorer (verson 6.0 or hgher) Screen resoluton 1, pxels 16- or 32-bt color depth Installed Sun JVM For playng back recordngs: connecton to storage medum Also note the nformaton n the System Requrements document on the product CD suppled. If necessary, you can nstall the requred programs and controls from the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). The Web browser must be confgured to enable Cookes to be set from the IP address of the unt. In Wndows Vsta, deactvate protected mode on the Securty tab under Internet Optons. You can fnd notes on usng Mcrosoft Internet Explorer n the onlne Help n Internet Explorer. Installng MPEG ActveX Sutable MPEG ActveX software must be nstalled on the computer to allow the lve vdeo mages to be played back. If necessary, you can nstall the program from the product CD suppled. 1. Insert the product CD nto the computer's CD-ROM drve. If the CD does not start automatcally, open the root drectory of the CD n Wndows Explorer and double-clck MPEGAx.exe. 2. Follow the on-screen nstructons. Bosch Securty Systems Installaton and Operatng Manual DOC V

90 90 en Operaton VdeoJet X10 SN Establshng the Connecton Before you can operate the VdeoJet X10 SN wthn your network, t must have a vald IP address for your network and a compatble subnet mask. The followng default address s preset at the factory: Start the Web browser. 2. Enter the IP address of the VdeoJet X10 SN as the URL. The connecton s establshed and after a short tme you wll see the LIVEPAGE wth the vdeo mage. DOC V Installaton and Operatng Manual Bosch Securty Systems

91 VdeoJet X10 SN Operaton en The LIVEPAGE Once the connecton s establshed, the Web browser dsplays the LIVEPAGE. It shows the lve vdeo mage on the rght of the browser wndow. Dependng on the confguraton, varous text overlays may be vsble on the lve vdeo mage (see Secton 5.13 Advanced Mode: Dsplay Stampng, page 40). Other nformaton may be shown next to lve vdeo mage on the LIVEPAGE. The dsplay depends on the settngs on the LIVEPAGE Functons page (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). Maxmum Number of Connectons If you do not connect, the unt may have reached ts maxmum number of connectons. Dependng on the unt and network confguraton, each VdeoJet X10 SN can have up to 25 Web browser connectons or up to 50 connectons va VIDOS or Bosch Vdeo Management System. Protected VdeoJet X10 SN If the VdeoJet X10 SN s password protected aganst unauthorzed access, the Web browser dsplays a correspondng message and prompts you to enter the password when you attempt to access protected areas. A VdeoJet X10 SN offers the opton to lmt the extent of access usng varous authorzaton levels (see Secton 5.11 Advanced Mode: Password, page 38). 1. Enter the user name and assocated password n the correspondng text felds. 2. Clck OK. If the password s entered correctly, the Web browser dsplays the page that was called up. Protected Network If a RADIUS server s employed n the network for managng access rghts (802.1x authentcaton), the VdeoJet X10 SN must be confgured accordngly, otherwse no communcaton s possble (see Secton Authentcaton, page 80). Image Selecton You can vew the mage of the camera n dfferent dsplays. Clck one of the tabs Stream 1, Stream 2 or M-JPEG below the vdeo mage to toggle between the dfferent dsplays of the camera mage. Bosch Securty Systems Installaton and Operatng Manual DOC V

92 92 en Operaton VdeoJet X10 SN Vew Control Control optons for perpherals (for example a pan/tlt head or dome camera) depend on the type of unt nstalled and on the confguraton of the VdeoJet X10 SN. If a controllable unt s confgured and connected to the VdeoJet X10 SN, the controls for the perpheral are dsplayed next to the vdeo mage. 1. To control a perpheral, clck the approprate controls. 2. Move the mouse cursor over the vdeo mage. Addtonal optons for controllng perpherals are dsplayed wth the mouse cursor. Dgtal I/O The alarm cons Input 1 to Input 4 are for nformaton purposes and ndcate the status of an alarm nput: When an alarm s trggered, the correspondng con lghts up blue. The unt's confguraton determnes whether the alarm s dsplayed, as well as addtonal detals (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). Trggerng Relay You can swtch connected unts usng the relays n the VdeoJet X10 SN (for example lghts or door openers). To actvate ths, clck the con for the correspondng relay next to the vdeo mage. The con wll be red when the relay s actvated. DOC V Installaton and Operatng Manual Bosch Securty Systems

93 VdeoJet X10 SN Operaton en 93 System Log / Event Log The System Log feld contans nformaton about the operatng status of the VdeoJet X10 SN and the connecton. You can save these messages automatcally n a fle (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). Events such as the trggerng or end of alarms are shown n the Event Log feld. You can save these messages automatcally n a fle (see Secton 5.15 Advanced Mode: LIVEPAGE Functons, page 42). 1. If you want to delete the entres, clck the delete con n the top rght-hand corner of the relevant feld. 2. If you want to vew a detaled log, clck the con n the top rght-hand corner of the relevant feld. A new wndow wll open. Audo Functon Dependng on the confguraton, the VdeoJet X10 SN can send and receve audo sgnals. All users who are connected by browsers receve the audo sgnals sent by the VdeoJet X10 SN. Audo sgnals can only be sent to the VdeoJet X10 SN by the user who connects to the unt frst. 1. On the LIVEPAGE, clck anywhere next to the vdeo mage to remove the focus from the ActveX. 2. Hold down the F12 key to make a voce connecton to the VdeoJet X10 SN. The browser's status bar dsplays the message Send Audo ON. 3. Release the F12 key when you want to stop sendng audo sgnals to the VdeoJet X10 SN. The status bar n Internet Explorer dsplays the message Send Audo OFF. When the connecton mantanng voce contact wth the VdeoJet X10 SN s broken, the next user to make a connecton to the VdeoJet X10 SN can send audo data to the VdeoJet X10 SN. Bosch Securty Systems Installaton and Operatng Manual DOC V

94 94 en Operaton VdeoJet X10 SN 6.3 Savng Snapshots You can save ndvdual mages from the vdeo sequence currently shown on the LIVEPAGE n JPEG format on your computer's hard drve. The con for recordng sngle mages s only vsble f the unt s confgured to enable ths process (see Secton Allow snapshots, page 43). Clck the con. The mage s saved at a resoluton of pxels (4CIF). The storage locaton depends on the confguraton of the VdeoJet X10 SN (see Secton Path for JPEG and MPEG fles, page 44). 6.4 Recordng Vdeo Sequences You can save sectons of the vdeo sequence currently shown on the LIVEPAGE on your computer's hard drve. The con for recordng vdeo sequences s only vsble f the unt s confgured to enable ths process (see Secton Allow local recordng, page 43). 1. Clck the con to start recordng. The storage locaton depends on the confguraton of the VdeoJet X10 SN (see Secton Path for JPEG and MPEG fles, page 44). A red dot n the con ndcates that recordng s n progress. 2. Clck the con agan to stop recordng. You can play back saved vdeo sequences usng the Player from Bosch Securty Systems, whch can be nstalled from the product CD suppled (see Secton 3.1 Scope of Delvery, page 11). Image Resoluton Sequences are saved at the resoluton that has been preset n the confguraton for the encoder (see Secton 5.19 Advanced Mode: Encoder Profle, page 46). 6.5 Runnng Recordng Program The hard drve con below the camera mages on the LIVEPAGE changes durng an automatc recordng. A movng graphc wll appear to ndcate a runnng recordng. If no recordng s takng place, a statc con s dsplayed. DOC V Installaton and Operatng Manual Bosch Securty Systems

95 VdeoJet X10 SN Operaton en The RECORDINGS Page The RECORDINGS page for playng back recorded vdeo sequences can be accessed from the LIVEPAGE and from the SETTINGS menu. The RECORDINGS lnk s only vsble f a storage medum has been selected (see Secton 5.21 Advanced Mode: Storage Management, page 50). Clck the RECORDINGS lnk n the navgaton bar n the upper secton of the wndow. The playback page appears. Camera Here you can select the camera from whch you want to vew the recordngs. Playback of the recordngs starts mmedately n the vdeo wndow. Recordng Here you can select the recordng that you want to vew. Playback of the recordng starts mmedately n the vdeo wndow. Controllng a Playback You wll see a tme bar below the vdeo mage for quck orentaton. A green arrow above the bar ndcates the poston of the mage currently beng played back wthn the sequence. Bosch Securty Systems Installaton and Operatng Manual DOC V