Table of Contents I. WiFi Power Pack (TP-Link) Setup via WiFi Page 1 II. Static IP Address through telnet.. Page 9
|
|
- Crystal Brown
- 6 years ago
- Views:
Transcription
1 How to configure WiFi Power Pack on Android Device Introduction Application Note Number: 271 This application note will show you how to setup the WiFi Power Pack to use with Star Printers on Android device. Depending on the application, further installation of printer drivers may be needed. Supported Printers: Thermal, Impact Printer Supported Interfaces: Ethernet Supported Environments: Android Table of Contents I. WiFi Power Pack (TP-Link) Setup via WiFi Page 1 II. Static IP Address through telnet.. Page 9 I. WiFi Power Pack (TP-Link) Setup via WiFi 1. Connect the TP-Link s USB to an AC power supply. Next, connect the TP-Link s Ethernet cable to the 100/10 Base port on the printer. The printer should be power off. 2. Confirm the TP-Link has a solid green or blue light. 11/11, V1.0 Page 1
2 3. On the android device, go to Settings. 4. Go to Wi-Fi. 11/11, V1.0 Page 2
3 5. Select Starwifi. 6. Confirm Starwifi is connected. 7. Open a web browser. 11/11, V1.0 Page 3
4 8. Type into the address bar and hit go. 9. It should prompt for authentication so please type the following: User Name: admin Password: admin 10. The TP-Link greeting screen will appear. 11/11, V1.0 Page 4
5 11. Click on Quick Setup in the menu on the left side. 12. Click on Next button. 13. Select Client (Client Mode) and click Next button. 11/11, V1.0 Page 5
6 14. The WiFi Power Pack will scan for available networks. 15. The AP List should appear. The SSID column lists the name of available networks. Find the network you wish to connect your printer to then click on Next. 16. Enter the password to the network then click on Next button. 11/11, V1.0 Page 6
7 17. Tap Next. 18. Tap Reboot button. 11/11, V1.0 Page 7
8 19. A screen will appear so click on OK button. 20. The TP-Link will restart. 21. Once completed, you will no longer be able to access the website ( ) 11/11, V1.0 Page 8
9 II. Static IP Address through telnet 1. At this point, the connection to should be lost. 2. Connect to your existing network on the Android device. 3. Perform a self-test page, by turning off the printer, holding the FEED button in the front then turning the printer back on. Hold the FEED button until the printer starts to print. NOTE: For the SP700 hold the feed button until it beeps then release. 4. On the second page towards the bottom, the IP Address, Subnet Mask, and Default Gateway will appear. (Your numbers may be different.) 11/11, V1.0 Page 9
10 5. Go to the App Store, and download Telnet Lite by MochaSoft. Open the application, once it downloaded and installed. 6. Once the application is open, then click on Configure. 11/11, V1.0 Page 10
11 7. Click on New 8. Type in the IP Address that printed from the self-test page, then click on Connect. 9. A blue screen will appear asking for login information. Please type the following: Login: root 11/11, V1.0 Page 11
12 Password: public 10. Type 1 and click on enter. 11. Type 1 and click on enter. 12. Type the IP Address from the self-test page and click on enter. (You number may be different.) 11/11, V1.0 Page 12
13 13. Type 2 then press enter. Next, type the Subnet Mask from the bottom of the self-test page and press enter. (You numbers may be different). 14. Type 3 then press enter. Next, type the Default Gateway from the bottom of the self-test page and press enter. (You numbers may be different). 15. Type 99 then press enter. 11/11, V1.0 Page 13
14 16. Type 99 then press enter. 17. Type 98 then press enter. 18. Type 1 then press enter. 19. The session with telnet should be closed. 11/11, V1.0 Page 14
15 20. The printer should have printed the printer s static IP Address. (Your numbers should be the same as the numbers at the bottom of the second printout.) 21. Once the self-test page prints then turn the printer off. 11/11, V1.0 Page 15
16 22. Remove the USB cable from AC power supply, and plug it into DK-module. Then plug the DK- Module into the DK port on the back of the printer. 23. Congratulations, you have successfully setup your Star Micronics Printer with the WiFi Power Pack! 11/11, V1.0 Page 16
17 Star Micronics Worldwide Star Micronics is a global leader in the manufacturing of small printers. We apply over 50 years of knowhow and innovation to provide elite printing solutions that are rich in stellar reliability and industry-respected features. Offering a diverse line of Thermal, Hybrid, Mobile, Kiosk and Impact Dot Matrix printers, we are obsessed with exceeding the demands of our valued customers every day. We have a long history of implementations into Retail, Point of Sale, Hospitality, Restaurants and Kitchens, Kiosks and Digital Signage, Gaming and Lottery, ATMs, Ticketing, Labeling, Salons and Spas, Banking and Credit Unions, Medical, Law Enforcement, Payment Processing, and more! High Quality POS Receipts, Interactive Coupons with Triggers, Logo Printing for Branding, Advanced Drivers for Windows, Mac and Linux, Complete SDK Packages, Android, ios, Blackberry Printing Support, OPOS, JavaPOS, POS for.net, Eco-Friendly Paper and Power Savings with Reporting Utility, ENERGY STAR, MSR Reading, futureprnt, StarPRNT How can Star help you fulfill the needs of your application? Don t just settle on hardware that won t work as hard as you do. Demand everything from your printer. Demand a Star! Star Micronics Co., Ltd. 536 Nanatsushinya Shimizu-ku, Shizuoka Japan Star Micronics America, Inc. 65 Clyde Road, Suite G Somerset, NJ USA Star Micronics EMEA Star House Peregrine Business Park, Gomm Road High Wycombe, Buckinghamshire HP13 7DL UK +44-(0) Star Micronics Southeast Asia Co., Ltd. Room 2902C. 29th Fl. United Center Bldg. 323 Silom Road, Silom Bangrak, Bangkok Thailand x /11, V1.0 Page 17
How To Share a Star Micronics Printer Driver On Windows
Introduction Application Note How To Share a Star Micronics Printer Driver On Windows This document explains how to configure the sharing feature on a Windows PC. The feature allows you to share a Star
More informationInstalling a Star TSP100Lan Printer on Windows OS using futureprnt v5.0 to v6.0
Installing a Star TSP100Lan Printer on Windows OS using futureprnt v5.0 to v6.0 Introduction Number: 280 This application note shows how to install a Star TSP100LAN Ethernet Printer on Windows OS using
More informationInstalling mpop on Windows
Installing mpop on Windows Introduction This application note shows how to install mpop printer on Windows via USB or Bluetooth. Number: 289 Supported Printers: mpop Supported Interfaces: USB, Bluetooth
More informationHow to reset a Star Ethernet Printer
How to reset a Star Ethernet Printer Application Note Number: 277 Introduction This application note shows how to reset your Ethernet Printer back to factory mode. Factory mode is needed when the printer
More informationInstalling a Star Portable Printer Driver (v b) on Windows OS
Installing a Star Portable Printer Driver (v1.0.1.4b) on Windows OS Introduction Number: 249 This application note shows how to install a Star Portable Printer Driver (v1.0.1.4b) on a Windows OS. Note:
More informationInstalling a portable printer on Windows Using Starprnt Driver
Installing a portable printer on Windows Using Starprnt Driver Introduction This application note shows how to install a portable printer on Windows via Bluetooth. Application Note Number: 293 Supported
More informationRegistering and Connecting Star Printer to Star Cloud Services
Registering and Connecting Star Printer to Star Cloud Services Introduction This application note shows how to register and connect Star Printer to Star Clouds Services. Application Note Number: 278 Supported
More informationInstalling a Star Ethernet Printer on Mac OS X via the Browser
Introduction Application Note Installing a Star Ethernet Printer on Mac OS X via the Browser This application note shows how to install a Star Ethernet printer with a Static IP Address using the browser.
More informationEnabling Keep Alive Functionality on Star Ethernet Printers (Linux/Mac)
Enabling Keep Alive Functionality on Star Ethernet Printers (Linux/Mac) Introduction This application note shows how to enable Keep Alive functionality on Star Micronics Ethernet Printers. While this document
More informationInstalling a Star TSP100 USB on Windows OS
Installing a Star TSP100 USB on Windows OS Application Note Number: 276 Introduction This application note shows how to install a Star TSP100 series USB Printer using the futureprnt Driver/Configuration
More informationWeb Browser Setup For Web-base POS Applications
Web Browser Setup For Web-base POS Applications Application Note Number: 291 Introduction This application note is to show the basic printer setup for most web based point of sales applications. Supported
More informationInstalling a Legacy Parallel Star Printer on Windows XP (Raster Driver)
Installing a Legacy Parallel Star Printer on Windows XP (Raster Driver) Introduction This application note shows how to install a Star Legacy Printer with a Parallel interface using the Star Micronics
More informationInstalling a Star Serial Printer on Windows 7/Vista/XP Using StarPRNT
Installing a Star Serial Printer on Windows 7/Vista/XP Using StarPRNT Introduction This application note shows how to install a Star Serial Printer using the StarPRNT Intelligence Driver/Configuration
More informationInstalling a USB or Ethernet TSP800Rx on Windows 7 / Vista / XP
Installing a USB or Ethernet TSP800Rx on Windows 7 / Vista / XP Introduction This application note will explains how to install a TSP800IIRx printer with a USB or Ethernet interface. The Secured TSP800Rx
More informationSetting Up Graphics (Logo, coupons, or Watermark) on TSP100 using futureprnt
Setting Up Graphics (Logo, coupons, or Watermark) on TSP100 using futureprnt Introduction Application Note Number: 284 This application note explains how to use the futureprnt Configuration Utility to
More informationInstalling a Star USB Printer on Windows 7/Vista/XP Using StarPRNT
Installing a Star USB Printer on Windows 7/Vista/XP Using StarPRNT Introduction This application note shows how to install a Star USB Printer using the StarPRNT Intelligence Driver/Configuration Utility
More informationAssigning OPOS Device Names to a Star Printers and Cash Drawer
Assigning OPOS Device Names to a Star Printers and Cash Drawer Introduction This application note shows how to add a Star Printer and a cash drawer attachment as OPOS devices. While these instructions
More informationAirPrint Users Manual
AirPrint Users Manual Revision 1.00 Star Micronics Corporation Special Devices Division 1 / 20 Content 1 Introduction... 3 1.1 Support model... 3 1.2 Support OS... 3 1.3 Trademarks... 3 2 Setting... 4
More informationDeveloper Guide STAR MICRONICS CO.,LTD. Rev1.3
Star CloudPRNT Developer Guide STAR MICRONICS CO.,LTD. Rev1.3 Star cloudprnt Developer Guide 1. Introduction P2 Overview P3 Printing Process Operating Environment P3 P4 2. Client configuration P5 3. Polling
More informationSet-up Manual for IFBD-HI01X/02X
Set-up Manual for IFBD-HI01X/02X Wireless LAN Printer WebPRNT CloudPRNT STAR MICRONICS CO.,LTD. Rev1.3 IFBD-HI01X/02X with Star Printer How to setup 1. Introduction P2 2. Web configuration utility P3 3.
More informationSet-up Manual for IFBD-HI01X/02X
Set-up Manual for IFBD-HI01X/02X Wireless LAN Printer WebPRNT CloudPRNT STAR MICRONICS CO.,LTD. Rev1.4 IFBD-HI01X/02X with Star Printer How to setup 1. Introduction P2 2. Web configuration utility P3 3.
More informationSM-S200 SM-S300 SM-T300 3" 80mm rugged Mobile Printer with LCD display & WiFi version
NEW SM-S400 SM-T300DB Bluetooth and Serial without Magnetic Stripe Reader SM-T301DB Bluetooth with MSR SM-T301DW WiFi version with MSR SM-T300 SM-S200 SM-S300 Mobile Printers Fast, lightweight and small.
More informationActive Club POS Hardware Setup
Active Club POS Hardware Setup The Active Club POS hardware package includes the following (see figure 1): Heckler stand for ipad APG Vasario 1616 cash drawer Connecting cable for cash drawer Star Micronics
More informationinstall the CAB file, but that should still not take but another minute to do 3. Plug the TP4000 back in and test print.
THERMAL PRINTERS TROUBLESHOOTING INSTALLED PRINTERS Before running any additional steps, first try unplugging the USB cable that connects the printer from the Terminal (not the printer), cycling the Power
More informationInstalling the PR IM Kitchen and Bar Printers.
Installing the PR IM Kitchen and Bar Printers. To correctly install the Kitchen and bar printers they must first be placed in their location, plugged in and connected via cat 5 Ethernet cable to the Router.
More informationCreated April Click the Windows Start button and navigate Programs > StarMicronics > Star TSP100 > TSP100 Configuration Utility
Page1 Created April 2009 This application note shows how to set up Star single-station printers for receipt printing from InfoTouch Store Keeper POS Software. While this application note was written using
More informationSoftware Manual. for Mac OS X. Supported Models. SP500 Series SP700 Series. Rev. 1.1
Software Manual for Mac OS X Supported Models SP500 Series SP700 Series Rev. 1.1 The company names and product names that appear in this manual are generally trademarks or registered trademarks of each
More informationDo More. AC1750 Smart WiFi Router. Model R6400v2
Do More AC1750 Smart WiFi Router Model R6400v2 WiFi Network Name and Password The preassigned WiFi network name (SSID) and network key (password) are unique to your router, like a serial number. Because
More informationInstalling the EPSON U2xx Series Printer using Ethernet Connection Using ATM_304E Driver
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Installing the EPSON U2xx Series Printer using Ethernet Connection
More informationInstalling and Configuring the Star TSP ECO Series Printers Using OPOS Drivers for Windows 7 (32/64BIT)
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Installing and Configuring the Star TSP ECO Series Printers
More informationSoftware Manual. for Mac OS X. Supported Models. TUP900 Series TUP500 Series. Rev. 1.0
Software Manual for Mac OS X Supported Models TUP900 Series TUP500 Series Rev. 1.0 The company names and product names that appear in this manual are generally trademarks or registered trademarks of each
More informationC-Assist Set up Guide
C-Assist Set up Guide Wireless connection to and projection from PCs Macs and Mobile Devices CASIO COMPUTER CO., LTD. Contents Heading Wirelessly Connecting your PC/Mac to your Casio Projector Page Process
More informationlinkzone User ManUal
LINKZONE User Manual Getting to Know Your Mobile Hotspot Power key WPS key LED indicator USB jack LED Description Part Power key WPS key LED indicators Charging / USB Port Reset Reboot Description Hold
More informationThermal Label Printer TSP828L. Software Manual. Linux. Rev. 3.1
Thermal Label Printer Software Manual Linux Rev. 3.1 The company names and product names that appear in this manual are generally trademarks or registered trademarks of each company. Table of Contents
More informationGuidelines of Ethernet for Using a Star Dvice. - Windows - Rev. 2.0
Guidelines of Ethernet for Using a Star Dvice - Windows - Rev. 2.0 Guidelines for Using a Star Ethernet Device on Windows The star dvice s IP address must be set in advance to use a star device that supports
More informationCreated March Double click the Office Manager icon on the desktop to launch the back office application.
Created March 2009 This application note shows how to set up Star Micronics printers for guest check and kitchen ticket printing from Inborne Technology s Point of Success Premium and Standard Software.
More informationCongratulations on the purchase of your new Clover Flex
Congratulations on the purchase of your new Clover Flex Set Up the Hardware What s included Clover Flex Charging cradle Receipt paper Power cord (2 for EU) Power brick Screwdriver Clover Flex Features
More informationHOW TO SETUP TP-LINK DECO
HOW TO SETUP TP-LINK DECO Ver 1.0 1 Before we start the TP-LINK DECO, we need to install TP-LINK DECO apps on our mobile. Goto PLAY STORE search for TP-LINK DECO Select TP-LINK DECO and install the apps
More informationHP AP5000 Installation Guide (XP)
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 HP AP5000 Installation Guide (XP) This document provides step-by-step
More informationQuick Setup Guide. for Standalone Omada Access Points. EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall
Quick Setup Guide for Standalone Omada Access Points EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall EAP110-Outdoor / EAP225-Outdoor / EAP225-Wall 1910012420 REV1.0.1 May 2018 Omada EAP
More informationConfiguring the TSP100 for POSERA Maitre D Software. Created April 2009
Created April 2009 This application note shows how to set up the USB TSP100 for guest check printing from POSERA Maitre D Software. Recommended Restaurant Printer Options: Splash Proof Cover, Vertical
More informationClick on Close button to close Network Connection Details. You are back to the Local Area Connection Status window.
How to configure EW-7228APn/EW-7416APn as a Repeater to extend wireless range This article can apply on EW-7228APn and EW-7416APn. We used screen shots of EW-7416APn in this instruction. We recommend you
More informationCreated September 2010
Created September 2010 The application note will show you how to install a Star Micronics printer on Debian 5.0. While these directions show to install a TSP650, these directions suffice for installing
More informationIpAlarm Module Set Up
Page 1 IpAlarm Module Set Up Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait for the LEDs to stabilize.
More informationHow to manually set up EW-7228APn to extender wireless range
How to manually set up EW-7228APn to extender wireless range 1. Find out the IP address of your computer. Have your computer get on Internet as normally, without EW-7228APn turning on. If you use a Windows
More informationDo More. Nighthawk AC1900 Smart WiFi Router. Model R6900P
Do More Nighthawk AC1900 Smart WiFi Router Model R6900P WiFi Network Name and Password The preassigned WiFi network name (SSID) and password (network key) are unique to your router, like a serial number.
More informationSoftware Manual. Applicable Models TSP100IIIU TSP100IIIBI TSP100IIILAN TSP100IIIW TSP100ECO TSP100GT TSP100LAN TSP100U/PUSB. Rev. 7.
Applicable Models TSP100IIIU TSP100IIIBI TSP100IIILAN TSP100IIIW TSP100ECO TSP100GT TSP100LAN TSP100U/PUSB Rev. 7.3a Contents 1. Installation and Uninstallation... 1 1.1. Installing futureprnt Software...1
More informationContents. 1. Downloading the ios Mobile App Configuration Additional Information... 9 LED indications... 9 Operating the Device...
Contents 1. Downloading the ios Mobile App... 2 2. Configuration... 2 3. Additional Information... 9 LED indications... 9 Operating the Device... 9 1 1. Downloading the ios Mobile App The Dialog Smartlife
More informationVISIT:
Welcome TO VISIT: http://www.touchbistro.com/onebox Please use this page to record important details about TouchBistro and your hardware. Notes: Wi-Fi Name: AirPort Name: AirPort Password: Thermal Printer
More informationCongratulations on the purchase of your new Clover Mobile
Congratulations on the purchase of your new Clover Mobile Set Up the Hardware What s included Optional Accessories USB wall charger USB cable Clover Mobile Dock Clover Mobile Printer Clover Mobile Clover
More informationClover Installation Guides. For Clover Go Clover Mobile Clover Mini
Clover Installation Guides For Clover Go Clover Mobile Clover Mini This document provides instructions to setup the 3 types of Clover terminals that are sold for Epicor Stand-Alone Processing. The three
More informationInstalling your Nokia Home
Installing your Nokia Home 1. Installing the Nokia Home app 2. Plugging in your Nokia Home 3. Pairing your Nokia Home with your Device 4. Installing your Nokia Home: - Creating a Nokia account (optional)
More informationquick setup tp-link
192.168.0.1 quick setup tp-link M5360 3G Mobile Wi-Fi, 5200mAh Power Bank User Guide and wait the Device to reboot and restore its factory default settings. SIM Card Slot: It's where to insert your SIM
More informationIpAlarm Module Set Up VirtuAlarm model
Page 1 IpAlarm Module Set Up VirtuAlarm model Note: This device is shipped configured for Ethernet connectivity. To use in this mode, connect the BLUE Jack (marked WAN) to your router and wait at least
More informationCongratulations on the purchase of your new Clover Mobile
Congratulations on the purchase of your new Clover Mobile Set Up the Hardware What s included Optional Accessories Clover Mobile Dock Clover Mobile Printer Clover Mobile Clover Clip Clover PIN Entry Aid
More informationDo More. Nighthawk X8 AC5300 WiFi VDSL/ADSL Modem Router. Model D8500
Do More Nighthawk X8 AC5300 WiFi VDSL/ADSL Modem Router Model D8500 WiFi Network Name and Password The preassigned WiFi network name (SSID) and network key (password) are unique to your modem router, like
More informationHP RP2 Installation Guide
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 HP RP2 Installation Guide This document provides step-by-step
More informationInstalling the EPSON U2xx Series Printer using Ethernet Connection Using APD_402E Driver
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Installing the EPSON U2xx Series Printer using Ethernet Connection
More information10 Steps to Getting Started with Restaurant Pro Express
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 10 Steps to Getting Started with Restaurant Pro Express Your
More informationHow to setup EW-7428HCn as a range extender for an existing Wi-Fi network
How to setup EW-7428HCn as a range extender for an existing Wi-Fi network Thank you for purchasing Edimax EW-7428HCn High Power Ceiling Mount Wireless PoE Range Extender / Access Point. This guide will
More informationNETGEAR genie Apps. User Manual. 350 East Plumeria Drive San Jose, CA USA. August v1.0
User Manual 350 East Plumeria Drive San Jose, CA 95134 USA August 2012 202-10933-03 v1.0 Support Thank you for choosing NETGEAR. To register your product, get the latest product updates, get support online,
More informationPePWave Mesh Connector User Manual
PePWave Mesh Connector User Manual Document Rev. 1.0 Jun-07 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright 1999-2007 PePWave Ltd. All Rights Reserved. PePWave and
More informationPackage Contents. AC1200 WiFi Router Model JR6100 Installation Guide
Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information
More informationInstalling the EPSON U2xx Series Printer using Parallel Connection Using ATM_304E Driver
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Installing the EPSON U2xx Series Printer using Parallel Connection
More informationStatMonitr Screen. Operating Your StatBroadcast. On Game Day (Mark V Model Surface RT)
Operating Your StatBroadcast StatMonitr Screen On Game Day (Mark V Model Surface RT) Last Rev: July 11, 2015 StatBroadcast Systems Below is the quick start guide for operating your StatMonitr Surface tablet.
More informationRP-D10 / RP-E10 SERIES POS PRINTER
RP-D10 / RP-E10 SERIES POS PRINTER SOPHISTICATED RECEIPT PRINTING SOLUTIONS FEATURES RP-D10 AND RP-E10 SERIES COMPACT With a stylish 129 mm-cube design, RP-D and RP-E series printers offer one of the smallest
More informationProcessNow Terminal User Guide
ProcessNow Terminal User Guide Table of Contents Product Overview ProcessNow Terminal... 3 Initial Setup Welcome Emails... 3 ProcessNow Initial Setup Instructions... 4 Initial Setup - USB - 8006L1 Card
More informationR6200v2 Smart WiFi Router Installation Guide
Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information
More informationPlease note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system.
Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please follow these steps to ensure that any changes made by your previous
More informationHP RP5800 Installation Guide
HP RP5800 Installation Guide One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 This document provides step-by-step
More informationStep 1: Find a spot for your Wifi point
Let's get you set up with your new Google Wifi system. Here s what you ll need to get started: Google Wifi point(s) Google Account Google Wifi app for Android 4 and up or ios 9 and up Broadband connection
More informationQuick Start. AC1600 WiFi VDSL/ADSL Modem Router Model D6400. Package Contents. NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA USA
Support Thank you for purchasing this NETGEAR product. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com.
More informationNCR. Wi-Fi Setup Assistant. User guide
NCR Wi-Fi Setup Assistant User guide 15 Contents 1 Getting started... 3 1.1 Features... 3 1.2 System Requirements... 3 1.3 Installing Wi-Fi Setup Assistant... 4 2 Configuring a Wi-Fi Printer... 6 2.1 Setup
More informationUNDERSTANDING DITTO GETTING STARTED
UNDERSTANDING DITTO GETTING STARTED ABOUT DITTO Ditto is a diverse screen-sharing solution that is designed to work for everyone. It makes screen sharing simple, intuitive and unlimited for the end user.
More informationQuick Start. AC1900 WiFi Cable Modem Router Model C7000v2. Package Contents. The box contains the following items.
Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We
More informationQuick Start Guide. Wireless IP Camera. Technical Support QG4_A
Technical Support Wireless IP Camera Quick Start Guide For Windows Client & Mac Client, please download the PC software: https://reolink.com/software-and-manual/ For advanced setup, please download the
More informationUNIBOX. Hotspot Management Application. Quick Start Guide
UNIBOX Hotspot Management Application Quick Start Guide 1. Unpacking Unibox and Verifying shipped components Receive hardware and verify hardware components such as Unibox, patch cable, unibox power adapter.
More informationPhone (US only): NETGEAR Phone (Other Countries): See
Universal Dual Band WiFi Extender Desktop/Wallplug WN3500RP Installation Guide CONNECT WIRED DEVICES WIRELESSLY 2.4 AND 5 GHz WIRELESS EXTENSION EXISTING ROUTER Extended Wireless Range Existing Router
More informationN900 Wireless Dual Band Gigabit Router
Trademarks NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information
More informationShenZhen Foscam Intelligent Technology Co., Ltd
ShenZhen Foscam Intelligent Technology Co., Ltd Quick Installation Guide-For MAC users Packing List 1) IP CAMERA X 1 2) Wi-Fi Antenna (only available for wireless model) 3) DC Power Supply X 1 4) Network
More informationCreated December 2008
Created December 2008 This application note shows how to print guest checks to a TSP100 printer using ASI Restaurant Manager POS Software. TSP100 Supported Interfaces: USB, Powered USB, or LAN ASI Restaurant
More informationTechnical Support. Package Contents. Dual Band 11ac WiFi Router R6200 Installation Guide
Technical Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at http://www.netgear.com/register.
More informationCreated April This application note shows how to set up an ethernet SP700 for kitchen ticket printing from POSERA Maitre D Software.
Created April 2009 This application note shows how to set up an ethernet SP700 for kitchen ticket printing from POSERA Maitre D Software. Recommended SP700 Restaurant Printer Options: Two Color Red/Black
More informationHow to setup WL-WN575A2/WL-WN575A3 Repeater Mode through Ethernet Cable
How to setup WL-WN575A2/WL-WN575A3 Repeater Mode through Ethernet Cable The following setup procedure is for INITIAL SETUP. If your product has been configured before, we suggest you to RESET the product
More informationIP Energizer Instructions
IP Energizer Instructions IP Energizer Instructions Versions: IP Energizer Controller 1.31 PAE025 3v26 Introduction In order to allow remote control of the IP Energizer you will need to set up its Wi-Fi
More informationDG-HR1160M Portable Power Bank 3G Router User Manual
DG-HR1160M Portable Power Bank 3G Router User Manual V1.0 2013-11-14 As our products undergo continuous development the specifications are subject to change without prior notice COPYRIGHT Copyright 2013
More informationSoftware Manual Net Configuration Tool Rev. 4.05
Software Manual Net Configuration Tool Rev. 4.05 http://www.bixolon.com Introduction 1. About this manual... 3 2. Supported Operating Systems... 3 3. Supported Printers... 4 4. Before Startup... 5 5. Installation
More informationPioneer Stealth Touch S-Line (with integrated Epson printer) Installation and Configuration
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Pioneer Stealth Touch S-Line (with integrated Epson printer)
More informationSoftware Installation Guide. Version 1.1
Software Installation Guide Version 1.1 Thank you for choosing an Airtopia product You are advised to read this manual carefully; it contains all the information you need about the right conditions for
More information1 Connect a computer and the NF10WV using an Ethernet cable. (A yellow Ethernet cable was provided with your NF10WV).
Wireless Setup Guide NF10WV FAQs Wireless Setup guide Login to Web User Interface 1 Connect a computer and the NF10WV using an Ethernet cable. (A yellow Ethernet cable was provided with your NF10WV). 2
More informationUser Guide for RTP 3280 Ethernet Interface
Description: User Guide for RTP 3280 Ethernet Interface RTP 3280 Thermal Receipt Printer comes with three different I/O interfaces in I/O board replaceable version. And one of the three I/O interface board
More informationNetis WF-2411 Quick Configuration Guide NTC November TCS Webinar 1
Netis WF-2411 Quick Configuration Guide 1 Background AARP Policy on Public WiFi No computer being used for AARP Foundation Tax-Aide work is allowed to be connected directly to a public WiFi All connections
More informationQuick Start. Package Contents. Nighthawk AC1900 WiFi Cable Modem Router for XFINITY Internet and Voice Model C7100V
Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We
More informationOpen the App Store and search for the Easy Color or True Color app. You can now link your smartphone with the Wi receiver in several ways.
Open the App Store and search for the Easy Color or True Color app. You can now link your smartphone with the Wi receiver in several ways. Default Setup: You can use one receiver as a Wifi Access Point.
More informationStar TSP100 ECO futureprnt Series Printer OPOS Installation for Windows 8
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Star TSP100 ECO futureprnt Series Printer OPOS Installation
More informationDo More. Nighthawk X4S AC2600 WiFi VDSL2/ADSL Modem Router. Model D7800
Do More Nighthawk X4S AC2600 WiFi VDSL2/ADSL Modem Router Model D7800 WiFi Network Name and Password The preset WiFi network name (SSID) and password (network key) are unique to your modem router, like
More informationTechnical Support. Package Contents. N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2 Installation Guide
Technical Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at NETGEAR.com/register.
More informationTELST R A E LITE GAT E WAY QUICK START GUIDE
TELST R A E LITE GAT E WAY QUICK START GUIDE WELCOME TO TELSTRA ELITE GATEWAY - THANK YOU FOR CHOOSING US! This guide is to help you get the most out of your Telstra Wireless Mobile Broadband experience.
More informationThermal Printer Configuration (EPSON)
Thermal Printer Configuration (EPSON) STEP A : IDENTIFY THE THERMAL PRINTER MODEL Check for your EPSON printer model by finding the label on the printer. Figure 1.1 For the example above (Figure 1.1),
More informationGIANT PRO. User Guide STD_REV1.0
GIANT PRO User Guide STD_REV1.0 Contents 1. Intro 2. Device Settings 3. Error Check 4. Maintenance Report 5. NFC Tag Setting 6. Smart WiFi Link 7. Bluetooth Pairing 8. Smart Coupon 9. e-receipt 3 6 9 10
More information