GEM-X255 CONTROL PANEL/COMMUNICATOR

Transcription

1 R R PROGRAMMING INSTRUCTIONS HARDWIRE WIRELESS GEM-X55 CONTROL PANEL/COMMUNICATOR GEMINI SYSTEM SYSTEM ARMED ARMED 0/0/00 0/0/97:00 :00AM ARMED STATUS NEXT/YES A 3 D E PRIOR/NO B 56 F AREA C 790G COMPUTERIZED SECURITY SYSTEM Quick Stat: GEM-RPCAe. Refe to the wiing diagam, connect the keypad(s), sien, aux. powe, aux. output, emote bus, eath gound, zone and telephone wiing. NOTE: See Installation Instuctions (WI093).. Connect AC powe fist and then the battey. 3. Configue the keypad (see page 5).. Access the Easy Menu Diven (Deale Pogam) Mode: Pess EEEEEE A Maste Secuity Code (on micoshield) Pess NO (g) Until ACTIVATE PROGRAM Y/N appeas on the keypad display. Pess YES (F) To Ente Deale Pogam Mode. (see page 6 fo pogamming guide). Napco 00 W09B 9/0

2 GEM-X55 Notes: Fo a GEM-X55 system compising 96 zones o less, the system may be keypad pogammed. A system lage than 96 zones must be downloaded with NAPCO PCD-Windows Vesion.. This manual contains Easy Pogam Mode instuctions, which allows the the fist 96 zones to be completely pogammed though Menu Diven Easy Pogam Mode. The GEM-X55 equies the use of vesion 7 fimwae GEM-RPCAe 7 keypads: The keypad vesion can be identified by a compatibility sticke on keypad caton as well as a poduct vesion numbe of 07. The poduct vesion numbe appeas as a digit numbe which follows a 5 digit date code stamped on the the inside end flap of the caton (ex: XXXXX07DR). This numbe will also appea on the poduct on a tiangula shaped sticke. The fimwae vesion of the keypad can also be ascetained by enteing the pogam mode it will ead [307 Pogam Mode]. The GEM-X55 equies the use of vesion 7 fimwae GEM-EZM- zone expansion modules. This vesion zone expansion modules can be identified by a compatibility sticke on the keypad caton as well as a poduct vesion numbe of. The poduct vesion numbe appeas as a digit numbe which follows a 5 digit date code stamped on the caton (ex: XXXXXDR). This numbe will also appea on the on the the inside end flap of the caton as well as on the cicuit boad on a tiangula shaped sticke. System featues Chime zone povides second distinct pulsating Chime Zone tone Set System Time and Date in Pogam Mode System Touble Audible Automatic Timeout Inhibit System Touble Audible Easy Pogamming of PC Peset Auto download ID and Callback Numbes Suppot of GEM-PRINT module Cancel Repoting Code Wieless Touble Repoting by Zone Page (Telco 3) Repoting Delay Page - Pogammable Numbe of Repots of Same Signal Page - Maximum Numbe of Consecutive Pages Specific Logging of Communication Failue Modes New Relay Event Aea Disamed (PCD- Windows pogammable only) Pogammable DST stat date (PCD-Windows pogammable only) CHANGES FROM PREVIOUS EDITION The following changes have been made to this manual (WI09B) since the pevious edition (WI09A): Page, Addess 09 Answe on Rings changed fom -9 to 3-9. Page 5, CS REPORTING CODES Addesses added fo Telemety Touble and Telemety Fail. Page 5, CS REPORTING CODES, Addess 096 Changed RF Receive Tampe to RF Tampe. Pages 33-37, ZONE OPTIONS: Duplicate addesses coected. Page 39, Addess 7 Ans. Machine P/U w/o Line Seizue deleted. Page 0, Addess, Bit Changed Don t Clea Aux. Relay with Am/Disam to Don t Clea Aux. Relay with Disam Page 0, Addess:, Bit Changed Aux. Output Chip on Keyfob Aming to Aux. Output Chip on Keyfob Am/ Disam NAPCO Secuity Systems, Inc. 333 Bayview Avenue, Amityville, New Yok 70 Fo Sales and Repais, call toll fee: (00) Fo diect line to Technical Sevice, call toll fee: (00) Intenet:

3 WI09B 9/0 TABLE OF CONTENTS SYSTEM PROGRAMMING OPTIONS... Intoduction... Downloading fom a Compute... EASY MENU DRIVEN PROGRAM MODE...5 Deale Pogam - Peliminay Infomation...5 Accessing Deale Pogam Mode...5 Customizing a Default Pogam...5 GEM-RPCAe...6 Numbe of Zones & Keypads pe Aea...6 Local o Cental Station Repoting System...6 Cental Station Receive Tel. Numbe...7 Cental Station Receive Account Numbe...7 Cental Station Receive Fomat... Ente Codes...9 RF Tansmitte Points... Key Fob Tansmittes... Ente Zone Desciptions... Ente Date... Ente Time...3 Ente Deale Code...3 Clea Deale Pogam...3 DIRECT PROGRAM MODE... Accessing Diect Addess Pogam Mode... Diect Addess Pogam Mode Keypad Commands...5 Pogamming Oveview...5 Diect Addess Pogamming Example...6 PROGRAMMING OPTIONS & WORKSHEETS...9 System Delays (Add , 0, 06 & )0 System Delays (Add 07, 0 & 0)...0 System Delays (Add 00, 0, & 03) Keypad System Codes (Add 090, 095 & 0500)... CS Receive Opt. (Add 050, 05, 055, 056, 0550, 055, 0575 & 0576)... CS Receive Tel. Numbes (Add , , )...3 Download/Callback Options (Add 09, , , 0 & 03)...3 CS Subscibe ID Numbes (Add )... Page 3 CS Repoting Codes (Add )... 5 CS Repoting Codes (Add )... 6 CS Aea & System Repoting Opt. (Add 0-07). 6 CS Zone Repoting Codes (Add )... 7 CS Repoting Codes (Add 030-0)... Global System Tbl. Repoting Opt. (Add 0-6) 9 Aea System Tbl. Repoting Opt. (Add 0-37).. 30 Zones -96 Options (Add )... 3 System Options (Add 5-9) System Options (Add 0- & 0)... 0 Keypad Options (Add 5-5)... 3 Aea Options (Add )... 3 EZM Goup Options (Add )... 5 Aea Aming Options (Add )... 6 Remote Access Logging (Add 3)... 6 Aea Output Contol Options (Add )... 6 RF Rcvs. & Sup. Times (Add 3776 & )... 7 System Reset Featues (Add )... USER PROGRAM MODE... 9 Peliminay Infomation... 9 Accessing Pogam Mode... 9 Codes... 9 Zone Desciptions CONFIGURATION MODE... 5 Keypad Installation... 5 Configuing the Keypads... 5 PROGRAMMING MODES PROGRAMMING OPTIONS INDEX... 5 GEM-X55 WIRING DIAGRAM LIMITED WARRANTY... 6 Refe to accompanying GEM-X55 Installation Instuctions (WI093) fo installation infomation. NOTE: THESE INSTRUCTIONS ARE INTENDED AND WRITTEN FOR PROFESSIONAL INSTALLATION PERSONNEL HAVING SUITABLE TRAINING, EXPERIENCE AND INSTALLATION EQUIPMENT. IT IS RECOMMENDED THAT AFTER PROGRAMMING, THE ERROR CHECK UTILITY OF THE PCD3000 DOWNLOADER BE USED TO VERIFY THAT THE CONTROL PANEL PROGRAM CONTAINS NO ERRORS OR CONFLICTS WHICH MAY INHIBIT ITS INTENDED OPERATION. L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

4 Page SYSTEM PROGRAMMING OPTIONS WI09B 9/0 INTRODUCTION The GEM-X55 contol panel may be pogammed by vaious means, each of which will be coveed in detail in the sections that follow. Keypad displays shown ae fo a GEM-RPCAe (Vesion 7), Downloading Fom a Compute. This is the pefeed method. The panel may be downloaded fom (o uploaded to) an IBM PC-compatible compute, with a 36 (o highe) micopocesso, eithe locally o emotely. NAPCO's PCD-Windows softwae, Vesion. o late featues context-sensitive help sceens as well as an eo-checking utility that pevents pogamming of incompatible o conflicting data to ensue pope panel opeation. Easy Menu Diven Pogam (Deale Pogam) Mode - Keypad Pogamming. The Easy Menu Diven Pogam Mode allows the pogamming of up to a 96 zone, aea system. A system lage than 96 zones must be pogammed via the PCD-Windows pogam. Keypad pogammable featues include numbe of zones in aea, numbe of zones in aea, fie zone numbes (both -wie and -wie), cental station epoting, enty/exit zone numbes, inteio zone numbes, numbe of keypads in aea, numbe of keypads in aea, cental station telephone numbe, cental station account numbe, auto download id numbe & PC peset callback telephone numbe, cental station eceive fomat, use codes, RF tansmitte points, RF key fob tansmittes,zone desciptions,date and time. Fo new panels, a custom default pogam may be ceated at the keypad. A menu-diven utility pompts the installe to configue the system. Futhe detailed customization is done in the Diect Addess Pogam Mode. Diect Addess (Deale Pogam) Pogam Mode - Keypad Pogamming. The Diect Addess Pogam Mode is an extension of the Deale Pogam Mode wheein data is enteed at the keypad by location. This mode is accessed fom the Easy Menu Diven Pogam Mode by pessing the C button at any time. Pogam Mode - Keypad pogamming. The Pogam Mode is intended fo authoized uses and is limited to keypad pogamming of Codes, Zone Desciptions, Time and Date. DOWNLOADING FROM A COMPUTER The contol-panel pogam may be downloaded fom the compute by eithe of the following methods. Local Downloading (Note: This pocedue should be used afte installation, afte peipheal devices ae connected.) Fo a diect high-speed data tansfe to the contol panel fom a desktop compute, connect the download jack (J) on the panel to the LOCAL jack (J3) on the Napco PCI000/3000 compute inteface using the supplied 6-conducto cable. (Refe to PCI000/3000 Installation Instuctions WI3 fo wiing diagam and pocedues.) Similaly, a high-speed local download may be made in the field using a notebook o laptop compute. Connect J on the contol panel to a Napco PCI-MINI compute inteface using the 6-conducto cable supplied. (Refe to PCI-MINI Installation Instuctions WI767.) Remote Downloading (Also see PCI000/3000 Installation Instuctions WI3.) Function Mode. Duing this pocedue, voice contact will be lost, theefoe both the installe and the compute opeato should be familia with the opeation. When a steady high-pitched tone is head at the site phone, access the ACTIVATE DOWNLOAD Function (see Keypad Pogamming Modes), then pess the J button o the YES (E) button; the site phone will go dead. Hang up the phone and wait fo a call fom the cental station confiming a successful download. Callback Method. An installed, unattended panel may be pogammed o epogammed emotely using the Callback- Method Download featue of PCD-Windows softwae. Remote downloading equies a modem compatible with the PCI000/3000. Upon answeing the call fom the compute, the panel will veify the Download Secuity Code and, if confimed, will establish a connection. If a Callback Numbe is pogammed into the panel, the panel will automatically disconnect and call the compute at this numbe befoe establishing a connection. The panel can suppot two Callback Numbes to allow downloads fom two diffeent offices. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

5 R NEXT/YES PRIOR/NO AREA R WI09B 9/0 EASY MENU DRIVEN PROGRAM MODE # OF ZONES IN AREA Page 5 GEMINI AI SYSTEM #ZN=0 ARMED #KP= A 0/0/97 ENTER #ZN=00 # ZONES #KP=0 :00AM X X COMPUTERIZED SECURITY SYSTEM DEALER PROGRAM - PRELIMINARY INFORMATION Only Keypad # may be used fo both deale and use pogamming, howeve this keypad may be located in any aea. The Maste Secuity Code is pinted on the panel s micopocesso can. Use this code to ente the Deale Pogam Mode to pogam a custom Deale Secuity Code. Recod the numbe, then emove the code label to pevent unauthoized access to the panel. If you foget you Deale Secuity Code, use the Maste Secuity Code to ente pogamming. Afte enteing codes o data, pess the save Jbutton. Data will not be stoed into memoy unless it is pessed. If the keypad is in the Pogam Mode and no activity is detected fo longe than minutes, a steady tone will sound. Silence the sounde by pessing the G button to continue, o by pessing the C button to exit. A panel that has been COLD STARTED (Addess Location 093) pefoms identically to a new panel. When pogamming moe than aeas, Diect Addess Pogamming Mode must be used to complete the pogam. ARMED STATUS A 3 D E B 56 F C 790G ACCESSING DEALER PROGRAM MODE CUSTOMIZING A DEFAULT PROGRAM Fo any new panel, you can design a default pogam that will best suit you application. Using this pocedue, you will configue the panel fo: This pocedue will automatically set up system keypads, EZMs, wieless tansmittes, etc. Afte you basic default pogam has been loaded, you may alte it as necessay in the Diect Addess Pogam Mode.. Pess EEEEEE A Maste Secuity Code (on micoshield). Pess g Until ACTIVATE PROGRAM Y/N appeas on the keypad display. 3. Pess F To Ente Deale Pogam Mode.. Pess CC To Exit Deale Pogam Mode when finished. GEM-P300 CONTROL COMMUNCIATOR MASTER SECURITY CODE # - # - # - # - # - # Accessing Deale Pogam Mode Numbe of Zones in Aea Numbe of Zones in Aea Fie Zones -Wie Fie Zones Local System o Cental Station Repoting Exit/Enty Zones Inteio Zones Numbe of Keypads in Aea Numbe of Keypads in Aea CS Receive Telephone Numbe Auto Download ID Numbe & P C Peset Callback Telephone Numbe CS Receive Account Numbe CS Receive Fomat Codes RF Tansmitte Points Key Fob Tansmittes Zone Desciptions * Date * Time * Deale Code * NOTE: GEM-RPCAe Keypad Only NEW PANELS: The custom default pogam may be ceated fo new panels only. Once the panel has been pogammed by any means, the numbe of aeas, numbe of zones, fie zones, enty/exit zones and inteio zones will be suppessed and cannot be changed. Should it be necessay to ceate a new custom default pogam, (a) fom the Deale Pogam Mode, pess the C button to ente the Diect Addess Pogam Mode; (b) access Location 09 (Clea Pogam); (c) pess the J button and stat ove. L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

6 NEXT/YES PRIOR/NO AREA R GEM-RPCAe Keypad: Zones pe Aea, Fie Zones, -Wie Fie Zones & CS Repoting Page 6 WI09B 9/0 A. GEM-RPCAe Keypad GEMINI AI SYSTEM ##ZN=0 OF ZONES ARMED #KP= IN AREA To ceate you customized default pogam using a GEM-RPCAe keypad, ente the following A 0/0/97 ENTER #ZN=00 # ZONES #KP=0 :00AM X X paametes. In each of the following steps, pess the A button to set cuso, the NEXT (E) A 3 D E B 56 F C 790G button to go fowads, the PRIOR (F) button to go backwads, the Jbutton to save and the C COMPUTERIZED SECURITY SYSTEM button twice to exit at any time. ARMED STATUS #OF ZNS IN AREA ENTER # ZONES 0 (Diect Enty) #OF ZNS IN AREA ENTER # ZONES 00 (Diect Enty) Total Numbe of Zones in Aea & Aea (Appeas fo New Panel Only) Diectly ente the total numbe of zones to be pogammed fo Aea and Aea, espectively. Valid enties ae fom 0 to 96. Diectly ente the total numbe of zones, including leading zeos. Use numbe buttons though 9. NOTE: Pess the 0 button fo a zeo. The system is based on goups of zones each (afte the fist zones), and will automatically ound up to the next goup of. Fo example, if you ente, it will automatically convet this to 0 zones. Pess Jto save. Pess NEXT (E) button to poceed. Note: The GEM-X55 is limited to a maximum of 96 zones and 5 keypads. All 96 zones and 5 keypads may be pogammed in the EZ Pogam Mode. Fo lage systems, efe to the PCD-Windows downloade. FIRE ZONES ENTER ZONE # 00 (Diect Enty) Fie Zones (Appeas fo New Panel Only) Ente the zone numbe of any Fie Zones (both -wie, -wie o wieless). Valid enties ae fom 0 to 96. Diectly ente each zone numbe, including leading zeos, and pess Jto save, and then epeat fo any additional zone(s). Pess NEXT (E) button to poceed. NOTE: If you ae pogamming a Aea system, ente the zone numbe of zones equied fo Aeas &. All fie zones ae common to aeas and. The Diect Addess Pogam Mode can then be used to customize them as needed. See Zone Options. -WIRE FIRE ZNS ENTER ZONE # 00 (Diect Enty) -Wie Fie Zones (Appeas fo New Panel Only) Ente the zone numbe of any Fie Zones (fom pevious question) which ae to be used with -wie smoke detectos. The only valid enties ae 0 though 0. Diectly ente each zone numbe, including leading zeos. Pess Jto save, and then epeat fo any additional zone(s). NOTE: Only zones which have been designated as Fie Zones can be pogammed as Wie Fie zones. Pess NEXT (E) button to poceed. NOTE: JP7 must be set to -WF position fo -wie fie zones 7 and (efe to Installation Instuctions). REPORT ALL ZONES TO CENTRAL? Y/N (Pess YES o NO) Local System o C.S. Repoting System (Appeas fo New Panel Only) Pess YES (E) button fo all zones to epot; pess NO (F) button fo no zones to epot (LOCAL SYSTEM). X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

7 WI09B 9/0 EXIT/ENTRY ZONES ENTER ZONE # 00 (Diect Enty) Page 7 Exit/Enty Zones (Appeas fo New Panel Only) Diectly ente the zone numbes which ae to be used as Exit/Enty zones. Valid enties ae fom 0 to 96. Diectly ente each zone numbe, including leading zeos. Use numbe buttons though 9. NOTE: Pess the 0 button fo a zeo. Pess Jto save and then epeat fo any additional zone(s). Pess NEXT (E) button to poceed. NOTE: Exit/Enty Zones will have an enty delay of 30 seconds and an exit delay of 60 seconds. Chime will automatically be pogammed fo all E/E zones. If you ae pogamming a Aea system, ente all of the zones equied fo Aeas &. INTERIOR ZONES ENTER ZONE # 00 Inteio Zones (Appeas fo New Panel Only) Diectly ente the zone numbes which ae to be used as Inteio Zones. Valid enties ae fom 0 to 96. Diectly ente each zone numbe, including leading zeos. Use numbe buttons though 9. NOTE: Pess the 0 (Diect Enty) button fo a zeo. Pess Jto save and then epeat fo any additional zone(s). Pess NEXT (E) button to poceed. NOTE: All Inteio zones will also be automatically pogammed as Exit/Enty Followe zones. If you ae pogamming a Aea system, ente all the zones equied fo Aeas &. # AREA S ENTER #KPS 0 (Diect Enty) # AREA S ENTER #KPS 00 (Diect Enty) CENTRAL PHONE # Numbe of Keypads in Aea Diectly ente the total numbe of Keypads to be installed in Aea. Valid enties ae fom 0 to 5. Diectly ente the numbe of keypads, including leading zeos. Use numbe buttons though 9. NOTE: Pess the 0 button fo a zeo. Pess Jto save. Pess NEXT (E) to poceed. Numbe of Keypads in Aea Diectly ente the total numbe of Keypads to be installed in Aea. Valid enties ae fom 0 to 5. Cental Station Receive Telephone Numbe Using numbe buttons, ente telephone numbe of up to 6 digits including pefix lettes, if necessay, fo eceive. Use numbe buttons though 9 fo digits 9; pess the G 0 button fo a zeo and G (Diect Enty) though G 5 fo lettes B F, espectively. NOTE: Pe-Dial Delay = D ; Dial-Tone Detection = E. Pessing the 0 button will poduce a blank space ( ). Pess Jto save. Pess NEXT (E) to poceed. NOTE: Cental Station Receive and 3 Telephone Numbes can only be enteed in Diect Addess Pogamming. See CS Receive Options. Easy Pogamming of Auto download ID #'s and PC Peset Callback Numbes Fo unattended PC Peset downloading, it is now possible to set the Auto download ID # s and PC Peset Callback fom the Keypad Easy Pogam Mode. At the field fo CENTRAL PHONE #, pogam an "F" followed by the Auto Download ID # ( digits) and then the Callback Telco # (up to 3 digits). Pess [ON/OFF] to save. Exit Pogam Mode ([RESET] [RESET]). Ente Maste Code Pess [FUNCTION] Go to Function "ACTIVATE DOWNLOAD Y/N" and pess YES (INTERIOR). The panel will automatically call the PC Peset compute and download the pogam on the specified Auto Download line # of PC Peset. CENTRAL PHONE # F Example: Pogam an Auto download ID # of 07 and a PC Peset Callback # of Go to Cental Phone # input sceen and pess: [*] [5] [0] [7] [] [5] [] [6] [] [] [] [9] [] [0] [0] [ON/OFF] GEM-RPCAe Keypad: Exit/Enty Zones, Inteio Zones, Keypads pe Aea, CS Tel. No. & CS Acct. No. L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

8 Page WI09B 9/0 Cental Station Receive Account Numbe CENTRAL STATION Ente an account numbe of up to fou digits. Use numbe buttons ACCOUNT #( ) though 9 fo digits 9. NOTE: Pess the 0 button fo a zeo and pess the G 0 buttons fo a blank space ( ).G though (Diect Enty) G 5 fo lettes B F, espectively. Pess Jto save. Pess NEXT (E) button to poceed. NOTE: Cental Station Receive and 3 Account Numbes can only be enteed in Diect Addess Pogamming. See CS Repoting Options. SEE WI FOR INFO RCVR FORMAT (0) (Diect Enty) Cental Station Receive Fomat Fom the table below, ente the cental station's eceive fomat. Use numbe buttons though 9. NOTE: Pess the 0 button fo a zeo. and pess the G 0 buttons fo a blank space ( ). Pess G though G fo lettes B E, espectively. Pess Jto save. Pess NEXT (E) button to poceed. GEM-RPCAe Keypad: CS Fomat DATA CS RECEIVER FORMAT ENTRY blank( ) Ademco Slow, Silent Knight Slow Sescoa, Vetex, DCI, Fanklin Fast Radionics Fast 3 Silent Knight Fast Radionics, DCI, Fanklin Slow 5 Univesal High Speed Radionics BFSK DATA CS RECEIVER FORMAT ENTRY 9 FBI /3/ 0 Radionics Modem B SIA C Ademco Point ID D Ademco Expess E Page NOTE: Modem IIe is available only in Diect Addess Pogamming. Cental Station Receive and 3 Fomats can only be enteed in Diect Addess Pogamming. See CS Receive Options. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

9 WI09B 9/0 ENTER USER CODE F3- # Code Option Access /Level Contol Page 9 Ente Codes (Pess the (A) button to set cuso.) Ente up to 95 Codes with Options, Authoity Level and Access Contol Options (if necessay) fo each code. Refe to the tables below and on the next page fo available data enties fo Options, Authoity Level and Access Contol Options. Note: The 95 s must be assigned to aeas in Enable Code by Aea (Addess ) in Diect Addess Pogamming. By default, only is enabled in Aea and Aea. - ae enabled in Aea and use 9-6 ae enabled in Aea. Pess the (A) button to set the cuso to the Code. Use the numbe buttons though 9 to ente a code of up to 6 digits. Ente up to 6 digits ( digits is ecommended) in the fist six boxes fom left to ight fo each use code. Valid enties ae: 0-9. Note: Pess the 0 button fo a zeo. No blank spaces in between; leave any tailing boxes. If an Ambush Code (Addess 095) is enteed, do not pogam the fist two digits of ANY Code as the same digits enteed fo the Ambush Code. If the pogammed code is less than 6 digits, pess the A button to set the cuso to the OPTION/LEVEL. Refe to the tables below fo the available Option and Level data enties. Ente the use options data in the left digit. Ente the level data (with aming options, if any, added) in the ight digit. Note: Fo enties geate than 9, pess the G buttons though the G5 buttons fo B though F, espectively. Fo Keypad Access Contol, pess the A button once again to pogam applicable keypads. Refe to the tables below, use the numbe buttons to ente the data fo Keypad in the ight digit; and the data fo Keypad 5 data in the left digit. (Pess the 0 buttons fo blank.) Example: Ente a code of 356 as 356 (fom left to ight). USER OPTIONS DATA ENTRIES BLOCKED VIEW USER PROGRAM BYPASS OVERVIEW DISABLED Y Y 3 Y Y Y 5 Y Y 6 Y Y 7 Y Y Y Y 9 Y Y 0 Y Y B Y Y Y C Y Y D Y Y Y E Y Y Y F Y Y Y Y Note: Y indicates option is enabled. USER CODE (UP TO 6 DIGITS) DATA AUTHORITY ENTRIES LEVEL USER OPTIONS USER OPTION CODE TYPE NONE ARM/DISARM LEVEL ARM/DISARM LEVEL ARM/DISARM 3 LEVEL 3 ARM/DISARM NONE ARM ONLY 5 LEVEL ARM ONLY 6 LEVEL ARM ONLY 7 LEVEL 3 ARM ONLY NONE SERVICE 9 LEVEL SERVICE 0 LEVEL SERVICE B LEVEL 3 SERVICE USER LEVEL ACCESS CONTROL S ACCESS CONTROL S DATA ENTRIES K.P. 5 K.P. 6 K.P. 7 K.P. NONE Y Y 3 Y Y Y 5 Y Y 6 Y Y 7 Y Y Y Y 9 Y Y 0 Y Y B Y Y Y C Y Y D Y Y Y E Y Y Y F Y Y Y Y Note: Y indicates option is enabled. ACCESS CONTROL S DATA ENTRIES K.P. K.P. K.P. 3 K.P. NONE Y Y 3 Y Y Y 5 Y Y 6 Y Y 7 Y Y Y Y 9 Y Y 0 Y Y B Y Y Y C Y Y D Y Y Y E Y Y Y F Y Y Y Y Note: Y indicates option is enabled. GEM-RPCAe Keypad: Codes L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

10 GEM-RPCAe Keypad: Codes Page 0 USER AUTHORITY LEVEL DISPLAY FUNCTION MENU FUNCTION LEVEL* DISPLAY ZN FAULTS DISPLAY ZN BYPASSED DISPLAY ZN DIRECTORY ACTIVATE BELL TEST DISPLAY PHONE # S DISPLAY SYS TRBL DISPLAY FIRE ALARM DISPLAY FIRE TRBL DISPLAY OP/CL 3 ACTIVATE OVERVIEW 3** ACTIVATE CHIME ACTIVATE WATCH RESET SYSTEM TRBL 3 RESET SENSOR MSG 3 START EXIT TIME FAULT FIND *** ACTIVATE LOCATE *** EZM ZONE FIND *** ACTIVATE DIALER TEST 3 DISPLAY ALARM LOG 3 DISPLAY TOTAL LOG 3 DISPLAY FIRE LOG 3 DISPLAY OP/CL LOG 3 DISPLAY SYSTEM LOG 3 AUTOARM IN -HRS DISPLAY AUTOARM SCHD 3 ACTIVATE PROGRAM 3** ACTIVATE DOWNLOAD 3 DISPLY RF XMITTER STAT RELAY CONTROL Pess Jto save each code. NOTES: * Minimum Level equied to access function ** Level-3 Code with appopiate use option *** Requies Deale Code OPTIONS Disabled Blocked View Pogam Bypass Oveview Am Only Sevice USER OPTIONS EXPLANATION Code not active in this aea. WI09B 9/0 Allows Code to block anothe code fom being viewed by anothe use. An unblocked code cannot view a blocked code, but a blocked code can view all codes. The maste use code and the deale pogam code can view all codes. Pogam Option is enabled fo Keypad only, wheeve it is connected (any aea). If enabled, Level 3 must also be enabled. Allows Code to bypass zones. This option, along with Level 3 Authoization, enables selection of OVERVIEW mode at a keypad. This Mode povides a system status display of all aeas at a glance. Pevents Code fom disaming this aea. A Sevice Code has esticted am/disam ights; if an aea is amed with a Sevice Code, a SERVICE ON appeas on the GEM-RPASe keypad (a S on the GEM-RPCAe keypad) and the aea can be disamed with any valid Code, including a Sevice Code. If the aea is amed with OTHER than a Sevice Code, it CANNOT be disamed with a Sevice Code. This is typically used to allow tadesmen access to pemises unde contol of the owne. Access This is nomally used to activate a doo stike while an aea is disamed. A code with the access option will not function as an am/disam code. When the code is enteed, the keypad will display ENTER NOW and the Bown Wie on the keypad will become Active Low (Gound Potential) fo 7 seconds. Related Options: Ambush Code (Addess 095), Panel Access Code (Addess 090), Deale Secuity Code (Addess 0500) & Enable Code by Aea (Addess ). To poceed to the next Code, set the cuso to the Numbe and change it using the numbe buttons. Pogam a new Code as peviously descibed. Pess NEXT (E) button to poceed. Example: Pogam a code of fo use 0, with Option of Pogam, Level 3 and Access Contol Option Keypad No.. Ente fo a use code, 3 fo use option and blank( ) fo access contol option. CHANGING OR CANCELING A CODE: To change any code, meely pogam ove the existing code as descibed above and pess Jto save. Similaly, to cancel a code, blank out each numbe of the code and pess Jto save to save. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

11 WI09B 9/0 ZN# XMIT#+CS P ZN : 0-0 Page RF Tansmitte Points (Pess the (A) button to set cuso.) (Fo wieless systems only. Also see Quick Method, which follows) Fo each tansmitte (key fob tansmittes also), ente the zone numbe (0 96) to which the tansmitte will be mapped, the 6-digit RF ID #:-digit Zone # Xmitte Check Point Mapped to ID Sum # checksum numbe pinted on the tansmitte and box, the point numbe ( ); ente 9 fo unsupevised (all points). NOTE: When pogamming the ID Code numbe, A = G 0; B = G ; C = G ; D = G 3; E = G ; F = G 5. Pess Jto save. Pess NEXT (E) button to poceed. ZN# XMIT#+CS P ZN : 0-0 ZN# XMIT#+CS P ZN0-ENROLL:A-- Quick Method. If a eceive is aleady installed in the panel, Napco tansmitte wieless points can be pogammed automatically ( enolled ) using the following pocedue. NOTE: The tansmitte point will be enolled only if the signal stength is 3 o geate.. Ente the zone numbe to which the tansmitte point will be mapped.. Pess the B button to ente the Enoll Mode. The ed and geen LEDs on the keypad will flash and the window will display as shown at left. 3. Open the loop of the point that is to be pogammed (GEM-TRANS o GEM-TRANS only).. Install the tansmitte battey. The keypad will beep to indicate that the point has been successfully enolled. Multi-point tansmittes can be mapped to successive zones simultaneously (Example ) o to selected zones point by point (Example ). Example. A -point tansmitte has the RF ID numbe 007:. Map the fist thee points to Zones 3, espectively.. Ente the Enoll mode as descibed in step above.. Ente Zone. 3. Open the loops of points, and 3.. Install the tansmitte battey. The keypad will beep 3 times to indicate that thee points have been pogammed. Tansmitte 007:, point will be mapped to Zone. Tansmitte 007:, point will be mapped to Zone. Tansmitte 007:, point 3 will be mapped to Zone 3. The keypad will now display Zone 3, the last zone enolled. Example. A -point tansmitte has the RF ID numbe 763:. Map point to Zone 6 and point to Zone 9.. Ente the Enoll mode as descibed above.. Ente Zone Open point- loop.. Install the battey. The keypad will beep once to indicate that one point has been pogammed. (Tansmitte 763:, point will be mapped to Zone 6.) 5. Ente Zone Close point- loop and open point- loop. 7. Remove the tansmitte battey, then e-install it. The keypad will beep once to indicate that one point has been pogammed. (Tansmitte 763:, point is mapped to Zone 9.) GEM-RPCAe Keypad: RF Tansmitte Points KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wieless panic buttons on one alam system, each epoting to a cental station, a page o having a desciption on the keypad that descibes the peson holding the key fob, the location whee the peson holding the key fob is stationed, o the special pupose of the key fob button being depessed. See the next page on Key fob Zone Assignment. L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

12 GEM-RPCAe Keypad: Keyfob Tansmittes, Zone Desciptions & Date Page Key Fob Tansmittes (Pess the (A) button to set cuso.) KF A XMIT#+ CS OP :0 00 KF Aea Xmitte Check Aux # ID Sum & DATA AUX /AUX OPTIONS ENTRY 0 None Relay Goup Toggle Relay Goup Toggle 3 Relay Goup 3 Toggle Relay Goup Toggle 5 Relay Goup 5 Toggle 6 Relay Goup 6 Toggle 7 Relay Goup 7 Toggle Relay Goup Toggle 9 Panic A Auxiliay B Instant C Aux. Output Toggle D Access on Aux. Output WI09B 9/0 Keyfobs can be pogammed as Am/Disam devices.(efe to WI75). Fo each Key Fob Tansmitte, ente: the Key Fob Tansmitte numbe (0 6). aea numbe to which tansmitte is assigned (-); ente 0 to disable keyfob. the 6-digit RF ID # pinted on the tansmitte (ente all numbes and/o lettes, including leading 0 s, if any). -digit checksum numbe pinted on the tansmitte (ente all numbes and/o lettes, including leading 0 s, if any). Aux- Option (see key fob aux & aux options). Aux- Option (see key fob aux & aux options). Note: If the Key Fob is conveted fo Two Button Emegency Use (by cutting an intenal jumpe), both top o bottom buttons must be depessed to activate an alam. In this case, Aux- and Aux- cannot be pogammed. Pess Jto save. Pess NEXT (E) button to poceed. Key Fob Zone Assignment (efe to display as shown on the pevious page: pess the (F) button to go backwads.) Each of the key fob buttons can be assigned to a zone. Fo example, On button = point ; Off button = point ; A = point 3; A = point. Up to 96 key fobs (using button) o key fobs (using buttons) o key fobs (using all buttons) o any combination up to a maximum of 96 contolled zones can be assigned, poviding multiple wieless panic buttons on a system, each epoting to the Cental Station o a page and/o annunciating on a keypad the key fob zone numbe with desciption/location. To assign a key fob to a zone: pogam the keyfob as you would a tansmitte, enteing the keyfob's ID code, check sum and point numbe at the appopiate zone. The Quick Method is not allowed. The zone may be hadwied to a senso as well as assigned to a key fob (eithe one will activate the zone alam output). NOTE: If assigning a key fob to a zone, the ON/OFF buttons on the key fob will no longe am/disam the system. The key fob is conveted to a panic only device. 00- (Diect Enty) NOTE: Key fobs -6 epot openings and closings as s Ente Zone and Inteio Desciptions Pess the and buttons to place the cuso; pess the 3 and 6 buttons to select the chaacte. Fo each zone, ente a desciption of up to two lines. Pess Jto save each desciption. To poceed to the next desciption, place the cuso unde the Zone Numbe (e.g. 0 ) and change the Zone Numbe using the 3 and 6 buttons. Pogam a new desciption as above. NOTE: Zone Desciptions can only be enteed though the GEM-/RPCAe Keypad o by using the Napco Quickloade Softwae. Pess NEXT (E) button to poceed. ENTER DATE (0/0/99) (Diect Enty) Ente Date (Pess the (A) button to set cuso.) Ente the cuent date in the fomat MM/DD/YY, whee MM = the month (0 ); DD=the day (0 3); and YY=the yea. Pess Jto save. Pess NEXT (E) button to poceed. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

13 WI09B 9/0 ENTER TIME (:05A) (Diect Enty) Page 3 Ente Time (Pess the (A) button to set cuso.) Ente the cuent time in the fomat HH:MMA/P, whee HH=hous (0 ); MM=minutes (00 59). Select Am o Pm by pessing any numbe button, then pess Jonce again to save. DEALER CODE (Diect Enty) DEALER CODE RE-ENTER (Diect Enty) Deale Code Diectly ente the Deale Code, including leading zeos. Use the though 9 buttons. NOTE: Pess the 0 button fo a zeo. Pess Jto save. Re-ente the Deale Code to veify the pevious code. Pess Jto save. Pess NEXT (E) button to poceed. NOTE: The Deale Code can be two o moe digits (up to 6 digits). EXIT DEALER PROGRAM MODE: This completes the custom default pogam. Pess the C button to ente the Diect Addess Pogam Mode fo futhe pogamming o pess the C button once again to end all pogamming and esume nomal keypad opeation. CLEAR PROGRAM: Should it be necessay to ceate a new custom default pogam, (a) fom the Deale Pogam Mode, pess the C button to ente the Addess Pogam Mode; (b) access Location 09 (Clea Pogam) o 093 (Cold Stat); (c) pess Jand then (d) pess the C button to exit the Deale Pogam Mode. A SYSTEM TROUBLE/E09-00 SERVICE will occu. Pess the C button to silence the keypad. 09 GEM-RPCAe Keypad 093 GEM-RPCAe Keypad Clea Deale Pogam (Eases Deale Pogam) This eases the deale pogam. Use this featue to stat a customized default pogam. Pogam Data and System Status Memoy is eased whee Scheduled Data and Zone Desciptions ae maintained. Access addess 09, then pess the Jbutton. Data enty is not allowed. NOTE: Ente Easy Menu Diven Pogam Mode to pogam system again. Cold Stat (Eases Entie Pogam) This eases the entie pogam including Pogam Data, Zone Desciption Data, System Status Data, Schedule Data and Foeign Language configuation(simila to a new panel). GEM-RPCAe Keypad: Time, Deale Code & Exit Deale Pogam Mode Access addess 093, then pess the Jbutton. Data enty is not allowed. NOTE: Some featues (schedules) can only be pogammed again with the Downloading Softwae. L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

14 NEXT/YES PRIOR/NO AREA R Page DIRECT PROGRAM MODE ARMED STATUS WI09B 9/0 GEMINI AI SYSTEM ##ZN=0 OF ZONES ARMED #KP= IN AREA A 0/0/97 ENTER #ZN=00 # ZONES #KP=0 :00AM X X A 3 B 56 C D E F G Accessing Diect Addess Pogam Mode. Pess EEEEEE A Maste Secuity Code (pinted on micopocesso can) o Deale Secuity Code (Addess 0500). Pess g Until ACTIVATE PROGRAM Y/N appeas on the keypad display. 3. Pess F To Ente Deale Pogam Mode DIRECT PROGRAM MODE DISPLAY & COMMANDS C (SECONDS) C = = DATA ENTRY LOCATION (Left and Right COMPUTERIZED SECURITY SYSTEM This is an extension of the Deale Pogam Mode. This method of pogamming is used in conjunction with the Keypad Pogamming Woksheets that follow. Refe to these woksheets to identify the -digit location (addess) of the featue to be pogammed. An illustative example is povided on the next page. LOCATIONS TO 093 DATA ENTRY LOCATIONS LEFT DIGIT RIGHT DIGIT 3 C HEXADECIMAL DATA: BLANK ( ) = No Options to 9 = Enties to 9 0 = Enty of 0 B to F = Enties to 5 ACCESSING DIRECT PROGRAM MODE PROGRAMMING OVERVIEW Diect Addess Pogamming allows you to go diectly to the addess locations and change the data enties to customize you contol panel options. Wheeas the Easy Menu Pogam Mode is a simple quick stat guide with limited options, the Diect Addess Pogam Mode is moe flexible allowing you to change all the options. It consists of multiple addess locations (up to 093) with two data enty locations each (left and ight) as shown in the adjacent diagam. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

15 WI09B 9/0 Page 5 The displays shown on the pevious page will appea afte a bief delay. Use the the A button to toggle the cuso between the -digit addess field and the data enty locations. Ente the addess diectly using the numbe buttons. The contents of the addess will be ead automatically, along with the featue name and pogamming infomation. The cuso will advance to the data field. Ente the equied data diectly using the numbe buttons. Pess Jto save the contents of each addess. EXIT DIRECT PROGRAM MODE: When done, pess C to exit and esume nomal keypad opeation. PROGRAMMING OVERVIEW The Keypad Pogamming Woksheets in the back ae povided as an addess-pogamming efeence to help the installe modify his custom default pogam o to make mino field alteations to an existing panel pogam. It is ecommended that the panel be uploaded to NAPCO's Quickloade softwae following any keypad pogamming and that the PCD-Window's eo-check featue be utilized to educe the possibility of pogamming omissions o conflicts. Note: Most of the addesses shown compise two data enty locations, left and ight digits. Pogam the left digits on the left data-display segment, and the ight digit on the ight segment. Fo those addesses having only one pogammable nibble, pogam the ight segment only; the left segment should display a. Keep the Keypad Pogamming Woksheets on file fo futue efeence. Geneal Pogamming Steps. Contact the cental station to ascetain eceive fomat, data fomat, event codes, subscibe numbes and telephone numbe(s).. Select the desied featues by cicling " the espective addess boxes. Refe to the Pogamming Options and Woksheets fo guidance in selecting the data (,,,) to be enteed into those boxes. 3. Pogam the data enteed in the boxes on the woksheets into the espective addesses. The display will show the enty numeically, but will display 0 fo the numbe 0, and lettes B, C, D, E, and F fo the numbes though 5, espectively. To pogam a 0, pess G 0. To pogam though 5, pess G though G 5, espectively. NOTE: See the Diect Addess Pogamming Example on the following page. DATA ENTRY SELECTIONS ENTRY TOTAL (BINARY VALUE CIRCLED) " PRESS N DISPLAY blank 0 " " # # # " # " $ $ $ " 0 G 0 0 $ " G B $ # G C $ # 3 G 3 D $ # " G E $ # " 5 G 5 F Table. Detemining data enty fo a location (each nibble ). Numbes in paentheses indicate data fo selected zones o featues. (See Pogamming Woksheets that follow.) Diect Addess Pogam Mode: Pogam Oveview & Geneal Pogamming Steps L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

16 Page 6 Diect Addess Pogamming Example Example: Pogam Zones 6, 7 and as Exit/Enty Followe Zones. WI09B 9/0 DETERMINE THE DATA ENTRIES. Refeing to ZONE FEATURES in the Pogamming Woksheets that follow, Exit/Enty Followe fo Zones 5 though ae located at addess, left digit. Cicle " the data values fo Zones 5.. Add the data values fo Zones 6, 7 and : ++=. Fom Tables and, (E) is enteed as pess G. The ight digit (fo Zones though, none of which ae Exit/Enty Followe Zones) is enteed as a. Diect Addess Pogam Mode: Pogamming Example PROGRAM THE DATA ENTRIES. Ente the panel's Deale Secuity Code (Addess 0500), then pess the A button.. Answe NO (F) to all questions until ACTIVATE PROGRAM Y/N is displayed; then pess YES (E). NOTE: If you pass ACTIVATE PROGRAM, scoll backwad using the the B button. 3. Pess the C button to ente the Addess Pogam Mode. Addess "0000" will display.. Pess to access Addess. The data fo both digits will display and the cuso will advance to the data field. 5. Pess G to ente an E in the left digit and pess 0 to ente a in the ight digit. 6. Pess Jto save. ZONE OPTION EXIT/ENTRY FOLLOWER Addess is now pogammed with E. ZONES SUM = ZN0 ZN07 ZN06 ZN05 $ # " L ADDR R E ENTER DATA " ZONES SUM = 0 ZN0 ZN03 ZN0 ZN0 X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

17 NEXT/YES PRIOR/NO AREA R WI09B 9/0 GEMINI AI SYSTEM ##ZN=0 OF ZONES ARMED #KP= IN AREA A 0/0/97 ENTER #ZN=00 # ZONES #KP=0 :00AM X X ARMED STATUS A 3 B 56 C D E F G PROGRAMMING OPTIONS & WORKSHEETS Page 7 COMPUTERIZED SECURITY SYSTEM. Pess EEEEEE A Pogam Option Deale Code (Addess 0500). Pess g Until ACTIVATE PROGRAM Y/N appeas on LCD sceen. 3. Pess F To Ente Deale Pogam Mode. Pess C To Exit Easy Menu Diven Pogam Mode & Ente Diect Addess Pogam Mode LOC. ENTER DATA " PROGRAMMING STEPS:. Lookup desied Pogamming Option by Addess Location (highlighted in black).. Select the pogamming option data enty fom the tables shown, by diect enty o by adding binay values. 3. Ente the selected data enty in the boxes shown.. Fo moe infomation on a pogamming option efe to the Glossay at the end of this manual. ENTRY TOTAL PRESS N DISPLAYS blank G 0 0 G B G C 3 G 3 D G E 5 G 5 F Detemining data enty fo a location (each nibble ). Numbes in paentheses indicate data fo selected zones o featues. (See Pogamming Woksheets that follow.) Diect Addess Pogam Mode: Pogamming Options & Woksheets DEFAULTS: The defaults shown on the following pages ae automatically set afte exiting the Easy Menu Diven L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

18 NEXT/YES PRIOR/NO AREA R Page WI09B 9/0 GEMINI AI SYSTEM ##ZN=0 OF ZONES ARMED #KP= IN AREA A 0/0/97 ENTER #ZN=00 # ZONES #KP=0 :00AM X X ARMED STATUS A 3 B 56 C D E F G COMPUTERIZED SECURITY SYSTEM THIS PAGE INTENTIONALLY LEFT BLANK X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

19 WI09B 9/0 Page 9 SYSTEM DELAYS & TIMEOUTS ( , 0, 06, & 390) EXIT DELAY (sec.) 0000 [Default = 3C] ENTRY DELAY (sec.) 000 [Default = E] ENTRY DELAY (sec.) 000 [Default = E] Aux. Output Access Contol Timeout (sec.) 0 ABORT DELAY (sec.) 06 DATA ENTRIES F E D 3 C F F DELAY/ TIMEOUT 0 sec. 5 sec. 30 sec. 5 sec. 60 sec. 90 sec. 0 sec. 55 sec.. Select delay/timeout (0-55 sec.) fom the table shown.. Ente in coesponding addess locations above (left and ight digits). 3. Fo a desied delay/timeout not listed do the following: A. Choose a desied delay/timeout, ex: 0 sec. B. Divide it by 6 Quotient Left Digit Remainde Right Digit Telephone Line Test Delay (sec.) CS Telco 3 Repot Delay (sec.) 390 EXIT/ENTRY DELAYS: Apply only to zones pogammed with the following options Enty/Exit, Enty/Exit, Exit/Enty Followe. Fo UL Installations, the maximum exit delay is 60 seconds and the maximum enty delay is 5 seconds. PROGRAMMING TIMEOUTS: Eithe use the tables povide o calculate you own timeout using the steps indicated. WARNING: Times have uncetainty of +/-sec, so a "time" of second may actually timeout IMMEDIATELY. CHIME TIMEOUT (¼sec.) SYSTEM DELAYS & TIMEOUTS ( 07, 0 & 0) 07 [Default = ] CHIME TIMEOUT OPTIONS DATA ENTRIES TIMEOUT 0 ¼sec. = 0 sec. ¼sec. = ½ sec. 3 3 ¼sec. = ¾ sec. ¼sec. = sec. 5 5 ¼sec. =.5 sec. 6 6 ¼sec. =.5 sec. 7 7 ¼sec. =.75 sec. ¼sec. = sec. AC Fail Repot Delay (min.) 0 AC FAIL REPORT DELAY OPTIONS DATA ENTRIES DELAY 0 min. 0 min. 0 min min. 0 min min min min. Senso Watch Delay (H.) 0 SENSOR WATCH OPTIONS DATA ENTRIES DELAY 0 H. H. H. 3 3 H. H. 5 5 H. 6 6 H. 7 7 H. System Delays/Timeouts F F 55 ¼sec. = 63.5 sec. F F 550 min. = H., 30 min. F F 55 H.. Select delay/timeout fom the table shown.. Ente in coesponding addess locations above (left and ight digits). 3. Fo a desied delay/timeout not listed do the following: A. Choose a desied delay/timeout, ex: 0. Note: Fo Senso Watch only divide it by 0, ex: 0/0 = B. Divide it by 6 Quotient Left Digit Remainde Right Digit L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

20 Page 0 WI09B 9/0 SYSTEM DELAYS & TIMEOUTS ( 00, 0, 03-05, 0 & 03) Reset Output Timeout (min.) 00 Aux. 0 Output Timeout (min.) [Default = ] Bug. 03 Alam Output Timeout (min.) [Default = ] Pulse 0 Alam Output Timeout (min.) [Default = ] Fie 05 Output Timeout (min.) [Default = ] System Delays/Timeouts & Keypad Codes DATA ENTRIES F F DELAY/ TIMEOUT 0 min. min. min. 3 min. min. 5 min. 6 min. 6 min. 55 min.. Select delay/timeout (0-55 min.) fom the table shown.. Ente in coesponding addess locations above (left and ight digits). 3. Fo a desied delay/timeout not listed do the following: A. Choose a desied delay/timeout, ex: 0 min. B. Divide it by 6 OUTPUT TIMEOUTS: If a timeout of 0 min. is selected, then the output will emain active (ON) until the system is eset o disamed. Fo UL Residential Installations, the minimum timeout is minutes. Fo UL Commecial Installations, the minimum timeout is 5 minutes. SYSTEM CODES ( 090, 095 & 0500) Panel Access Code Quotient Left Digit Remainde Right Digit L R L R L R [Default = fom addess ] Auto 03 Disam Ream Delay (min.) PANEL ACCESS CODE: Ente up to 6 digits to activate a doo stike while the aea is disamed.. Ente in both left and ight digits of addess locations.. Valid enties ae: 0-9. Note: Also, Access Contol on Aux. Output (Addess ) and Aux. Output Access Contol Timeout (Addess 0) must both be enabled. Ambush Code 095 AMBUSH CODE: Ente a -digit code used just pio to disaming and will activate an Ambush Condition, causing a SILENT epot to be sent to the cental station.. Ente in both left and ight digits of addess locations.. Valid enties ae: 0-9. Note: Also, Enable Keypad Ambush (Addess 0-6), Repot on Ambush Alam (Addess 5, 7, 35 & 37) and Ambush Code (Addess 0900) must all be enabled. Repot Cancel Window (sec.) 0 Deale Secuity Code L R L R L R [Default = fom addess ] DEALER SECURITY CODE: Ente up to 6 digits to be used by the deale to ente pogamming.. Ente in both left and ight digits of addess locations.. Valid enties ae: 0-9. Note: If left blank, the Maste Secuity Code must then be used to ente pogamming. X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems

21 WI09B 9/0 Page CS RECEIVER FORMAT OPTIONS ( 050, 05, 055, 056, 0550, 055, 0575 & 0576) CS Receive Fomat 055 CS Receive Fomat 0550 CS Receive 3 Fomat 0575 Default fo CS Receive Fomat depends on Easy Menu Question RCVR FORMAT. [Default = (blank) (blank)] fo CS Receives and 3 Fomats. DATA ENTRIES B C D E CS RECEIVER OPTIONS Sum Check 3/ with Extended Restoes RESERVED RESERVED CS RECEIVER OPTIONS Sum Check 3/ with Extended Restoes RESERVED RESERVED CS RECEIVER 3 OPTIONS Sum Check 3/ with Extended Restoes RESERVED RESERVED CS RECEIVER FORMATS Ademco Slow, Silent Knight Slow Sescoa, Vetex, DCI, Fanklin Fast Radionics Fast Silent Knight Fast Radionics, DCI, Fanklin Slow Univesal High Speed Radionics BFSK FBI /3/ Radionics Modem SIA Ademco Point ID Ademco Expess Page Radionics Modem IIe LEFT DATA LEFT DATA LEFT DATA CS RECEIVER FORMATS: Up to 3 CS Fomats may be pogammed.. Select the desied CS Receive Fomat fom the table shown.. Ente in the coesponding left and ight digit addess locations fo each CS Receive. NOTE: Dak shaded data value box shows option not available. Leading Digits fo Page Fomat (st Digit) LEFT DIGIT (SUM OF DATA ) 056 RIGHT DIGIT (SUM OF DATA ) LEFT DIGIT (SUM OF DATA ) 055 RIGHT DIGIT (SUM OF DATA ) LEFT DIGIT (SUM OF DATA ) RIGHT DIGIT (SUM OF DATA ) CS RECEIVER OPTIONS: Select options fo any of the thee CS Receives.. Select the desied option by cicling " the data values fo each digit (left and ight).. Add the data values (ex: 5=+++) fom the selected options. 3. Ente in addess location (left and ight digits). NOTE: Dak shaded data value box shows option not available. Leading Digits fo 05 Page Fomat (nd Digit) LEADING DIGITS FOR PAGER FORMAT: In Page Fomat epoting, the message typically begins with 00. Howeve, fo some page sevices, this will cause the Page's Voice Mail featue to activate. This option allows you to pogam these digits to any numbe desied. Typical Page epot is , whee 3 is the Event, is the zone, and 3 is the Subscibe ID numbe. Fo example, if the Leading Digits ae pogammed as 9, the Page epot will now appea as Ente in st and nd Leading Digits in ight digit only (left digit is not used) as shown.. Valid enties ae: 0-9. RIGHT DATA RIGHT DATA RIGHT DATA CS RECEIVER OPTIONS 00Hz Handshake/Kissoff * 300Hz Handshake/Kissoff * Enable Zone Numbe on Pulse Alam Single Digit Only CS RECEIVER OPTIONS 00Hz Handshake/Kissoff * 300Hz Handshake/Kissoff * Enable Zone Numbe on Pulse Alam Single Digit Only CS RECEIVER 3 OPTIONS 00Hz Handshake/Kissoff * 300Hz Handshake/Kissoff * Enable Zone Numbe on Pulse Alam Single Digit Only NOTE: * If both ae selected, 00Hz has pioity ove 300Hz. CS Receive Fomat Options L NAPCO Secuity Systems X GEM-X55 Pogamming Instuctions

22 Page WI09B 9/0 CS RECEIVER TELEPHONE NUMBERS ( , , ) CS Receive Telephone Numbes & Download/Callback Options CS Receive Telephone Numbe (Digits -0) CS Receive Telephone Numbe (Digits -0) CS Receive 3 Telephone Numbe (Digits -0) (RIGHT DIGITS -0) (RIGHT DIGITS -0) (RIGHT DIGITS -0) CS RECEIVER TELEPHONE NUMBERS: Ente telephone numbes fo any of the thee CS Receives (Telco, & 3).. Ente in ight digit only (left digit is not used).. Ente up to 0 digits fom left to ight. NOTE: Leave tailing boxes. 3. Valid enties ae: -9, B = *button, C = #button, D = 3 sec. pause, E = Wait fo dial tone, F = ignoe location Default fo CS Receive Telephone Numbe depends on Easy Menu Question CENTRAL PHONE #. [Default = ] acoss digits -0 fo CS Receive Telephone Numbes and 3. DOWNLOAD/CALLBACK OPTIONS ( 09, , , 0 & 03) No. Rings Befoe Pickup 09 [Default = F] NUMBER OF RINGS BEFORE PICKUP: Ente the numbe of ings befoe automatic pickup by the contol panel when downloading fom a compute (see Glossay at the back fo moe infomation).. Ente in ight digit only (left digit is not used).. Valid enties ae: 3-9, 0 = 0, B =, C =, D = 3, E =, F = 5 NOTE: Default is 5 Rings. Dak shaded data shows option not available (RIGHT DIGITS -0) Callback Telephone Numbe (Digits -0) [Default = fo all digits -0] (RIGHT DIGITS -0) Callback Telephone Numbe (Digits -0) [Default = fo all digits -0] CALLBACK TELEPHONE NUMBERS: Ente telephone numbes to be used when downloading fom a compute.. Ente in ight digit only (left digit is not used).. Ente up to 0 digits fom left to ight. NOTE: Leave tailing boxes. 3. Valid enties ae: 0-9, B = *button, C = #button, D = 3 sec. pause, E = Wait fo dial tone, F = ignoe location Download Secuity Code L R L R L R Callback Telephone No. Select 0 Auto Download ID No. 03 DOWNLOAD SECURITY CODE: Ente up to 6 digits to be used fo emote access when downloading fom a compute.. Ente in both left and ight digits of addess locations.. Valid enties ae: 0-9. Note: Download Secuity Code must match the code enteed in the PCD3000 Softwae. CALLBACK TELEPHONE NO. SELECT: Ente eithe fo Callback Telephone Numbe o fo Callback Telephone Numbe.. Ente in ight digit only (left digit is not used).. Valid enties ae: o. Valid enties X GEM-X55 Pogamming Instuctions L NAPCO Secuity Systems