Dell Latitude E5270. Owner's Manual. Regulatory Model: P23T Regulatory Type: P23T001

Transcription

1 Dell Ltitude E5270 Owner's Mnul Regultory Model: P23T Regultory Type: P23T001

2 Notes, cutions, nd wrnings NOTE: A NOTE indictes importnt informtion tht helps you mke etter use of your product. CAUTION: A CAUTION indictes either potentil dmge to hrdwre or loss of dt nd tells you how to void the prolem. WARNING: A WARNING indictes potentil for property dmge, personl injury, or deth Dell Inc. or its susidiries. All rights reserved. Dell, EMC, nd other trdemrks re trdemrks of Dell Inc. or its susidiries. Other trdemrks my e trdemrks of their respective owners Rev. A03

3 Contents 1 Working on your computer... 6 Sfety instructions... 6 Before working inside your computer...6 Turning off your computer...7 After working inside your computer Removing nd instlling components... 8 Recommended tools...8 Instlling the Suscrier Identifiction Module SIM crd...8 Removing the Suscrier Identifiction Module SIM crd...8 Removing the se cover... 9 Instlling the se cover...9 Removing the ttery...9 Instlling the ttery...10 Removing the hrd drive ssemly Removing the hrd drive from the hrd drive rcket...11 Instlling the hrd drive into the hrd drive rcket...12 Instlling the hrd drive ssemly...12 Removing the optionl M.2 Solid Stte Drive SSD...12 Instlling the optionl M.2 SSD Removing the optionl PCIe SSD Instlling the optionl PCIe SSD...13 Removing the memory module Instlling the memory module Removing the WLAN crd...14 Instlling the WLAN crd...15 Removing the WWAN crd Instlling the WWAN crd...15 Removing the dock frme Instlling the dock frme...17 Removing the power connector port Instlling the power connector port Removing the keyord Instlling the keyord...18 Removing the disply ssemly Instlling the disply ssemly...20 Removing the touchpd utton Instlling the touchpd utton Removing the optionl SmrtCrd reder ord Instlling the optionl SmrtCrd reder ord...22 Removing the optionl finger print reder ord Instlling the optionl finger print reder ord...23 Removing the LED ord...23 Contents 3

4 Instlling the LED ord Removing the het sink ssemly...24 Instlling the het sink ssemly...25 Removing the coin cell ttery...25 Instlling the coin cell ttery Removing the spekers...26 Instlling the spekers...27 Removing the system ord Instlling the system ord Removing the plmrest Instlling the plmrest System setup options Boot Sequence...30 Nvigtion keys...31 System Setup overview Accessing System Setup Generl screen options...31 System Configurtion screen options...32 Video screen options Security screen options...34 Secure Boot screen options Intel Softwre Gurd Extensions screen options Performnce screen options...37 Power Mngement screen options...38 POST Behvior screen options Virtuliztion support screen options...40 Wireless screen options...40 Mintennce screen options System Log screen options Updting the BIOS in Windows System nd setup pssword...42 Assigning system pssword nd setup pssword...42 Deleting or chnging n existing system nd or setup pssword Technicl specifictions System specifictions...44 Processor specifictions Memory specifictions Storge specifictions Audio specifictions...45 Video specifictions...46 Cmer specifictions Communiction specifictions...46 Port nd connector specifictions...46 Contctless smrt crd specifictions...47 Disply specifictions Contents

5 Keyord specifictions...48 Touchpd specifictions...48 Bttery specifictions...49 AC Adpter specifictions...49 Physicl specifictions Environmentl specifictions Dignostics...51 Enhnced Pre-Boot System Assessment epsa dignostics...51 Device sttus lights...52 Bttery sttus lights Contcting Dell...54 Contents 5

6 Working on your computer 1 Sfety instructions Use the following sfety guidelines to protect your computer from potentil dmge nd to ensure your personl sfety. Unless otherwise noted, ech procedure included in this document ssumes tht the following conditions exist: You hve red the sfety informtion tht shipped with your computer. A component cn e replced or, if purchsed seprtely, instlled y performing the removl procedure in the reverse order. WARNING: Disconnect ll power sources efore opening the computer cover or pnels. After you finish working inside the computer, replce ll covers, pnels, nd screws efore connecting to the power source. WARNING: Before working inside your computer, red the sfety informtion tht shipped with your computer. For dditionl sfety est prctices informtion, see the Regultory Complince Homepge t CAUTION: Mny repirs my only e done y certified service technicin. You should only perform trouleshooting nd simple repirs s uthorized in your product documenttion, or s directed y the online or telephone service nd support tem. Dmge due to servicing tht is not uthorized y Dell is not covered y your wrrnty. Red nd follow the sfety instructions tht cme with the product. CAUTION: To void electrosttic dischrge, ground yourself y using wrist grounding strp or y periodiclly touching n unpinted metl surfce tht is grounded to ground yourself efore you touch the computer to perform ny disssemly tsks. CAUTION: Hndle components nd crds with cre. Do not touch the components or contcts on crd. Hold crd y its edges or y its metl mounting rcket. Hold component such s processor y its edges, not y its pins. CAUTION: When you disconnect cle, pull on its connector or on its pull-t, not on the cle itself. Some cles hve connectors with locking ts; if you re disconnecting this type of cle, press in on the locking ts efore you disconnect the cle. As you pull connectors prt, keep them evenly ligned to void ending ny connector pins. Also, efore you connect cle, ensure tht oth connectors re correctly oriented nd ligned. NOTE: The color of your computer nd certin components my pper differently thn shown in this document. Before working inside your computer To void dmging your computer, perform the following steps efore you egin working inside the computer. 1 Ensure tht you follow the Sfety instructions. 2 Ensure tht your work surfce is flt nd clen to prevent the computer cover from eing scrtched. 3 Turn off your computer. CAUTION: To disconnect network cle, first unplug the cle from your computer nd then unplug the cle from the network device. 4 Disconnect ll the network cles from the computer. 5 Disconnect your computer nd ll ttched devices from the electricl outlets. 6 Press nd hold the power utton while the computer is unplugged to ground the system ord. 7 Remove the cover. CAUTION: Before touching nything inside your computer, ground yourself y touching n unpinted metl surfce, such s the metl t the ck of the computer. While you work, periodiclly touch n unpinted metl surfce to dissipte sttic electricity, which could hrm internl components. 6 Working on your computer

7 CAUTION: Mke sure tht you plce the cooler outlet side of your system t lest 5 cm wy from wll to prevent system overhet. CAUTION: Your system cnnot e plced crosswise nd mke sure tht there is no equipment on the side cover. Turning off your computer After working inside your computer After you complete ny replcement procedure, ensure tht you connect ny externl devices, crds, nd cles efore turning on your computer. CAUTION: To void dmge to the computer, use only the ttery designed for this prticulr Dell computer. Do not use tteries designed for other Dell computers. 1 Replce the ttery. 2 Replce the se cover. 3 Connect ny externl devices, such s port replictor or medi se, nd replce ny crds, such s n ExpressCrd. 4 Connect ny telephone or network cles to your computer. CAUTION: To connect network cle, first plug the cle into the network device nd then plug it into the computer. 5 Connect your computer nd ll ttched devices to their electricl outlets. 6 Turn on your computer. Working on your computer 7

8 Removing nd instlling components This section provides detiled informtion on how to remove or instll the components from your computer. Recommended tools The procedures in this document require the following tools: Phillips #0 screwdriver Phillips #1 screwdriver Smll plstic scrie Instlling the Suscrier Identifiction Module SIM crd 1 Follow the procedure in Before working inside your computer. 2 Insert pperclip or SIM crd removl tool into the pinhole to remove the SIM crd try [1]. 3 Plce the SIM crd on the SIM crd try [2]. 4 Push the SIM crd try into the slot until it clicks into plce. 2 Removing the Suscrier Identifiction Module SIM crd CAUTION: Removing the SIM crd when the computer is on my cuse dt loss or dmge the crd. Ensure your computer is turned off or the network connections re disled. 1 Insert pperclip or SIM crd removl tool into the pinhole on the SIM crd try. 2 Remove the SIM crd from the SIM crd try. 3 Push the SIM crd try into the slot until it clicks into plce. 8 Removing nd instlling components

9 Removing the se cover 1 Follow the procedure in Before working inside your computer. 2 To remove the se cover: Loosen the screws tht secure the se cover to the computer [1]. Lift the se cover from the edge nd remove it from the computer [2, 3]. NOTE: You my need plstic scrie to lift the se cover from the edges. Instlling the se cover 1 Align the se cover with the screw holders on the computer. 2 Press the edges of the cover until it clicks into plce. 3 Tighten the screws to secure the se cover to the computer. 4 Follow the procedure in After working inside your computer. Removing the ttery NOTE: Dischrge the ttery s much s possile efore removing from the system. This cn e done y disconnecting the A/C dpter from the system (while the system is turned on) to llow the system to drin the ttery. 1 Follow the procedure in Before working inside your computer. 2 Remove the se cover. 3 To remove the ttery: Disconnect the ttery cle from the connector on the system ord [1]. Remove the screws tht secure the ttery to the computer [2]. NOTE: The numer of screws will vry depending on the type of ttery instlled. c Lift the ttery wy from the computer [3]. Do not pply pressure to the surfce of the ttery Do not end Do not use tools of ny kind to pry on or ginst the ttery If ttery cnnot e removed within the constrints ove, plese contct Dell technicl support Removing nd instlling components 9

10 4 Unroute the cle from the routing chnnel [1] nd remove the cle from the ttery [2]. NOTE: This step is pplicle only for 4-cell ttery. Instlling the ttery NOTE: If your computer supports 6-cell ttery, it will not support hrd drive. 1 Connect the ttery cle to the connector on the ttery. 2 Route the ttery cle through the routing chnnel on the ttery. NOTE: This step is pplicle only for 4-cell ttery. 3 Insert the ttery into the slot on the computer. 4 Tighten the screws to secure the ttery to the computer. NOTE: The numer of screws will vry depending on the type of ttery instlled. 5 Connect the ttery cle to the connector on the system ord. 6 Instll the se cover. 7 Follow the procedure in After working inside your computer. Removing the hrd drive ssemly If the system is shipped with hrd drive ssemly perform the following steps. 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 To remove the hrd drive ssemly: Disconnect the hrd drive cle from the connector on the system ord [1]. Remove the screws tht secure the hrd drive ssemly to the computer [2]. c Lift the hrd drive ssemly wy from the computer [3]. 10 Removing nd instlling components

11 Removing the hrd drive from the hrd drive rcket 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery c hrd drive ssemly 3 Pull the hrd drive cle to remove it from the connector. 4 Remove the screws tht secure the hrd drive rcket to the hrd drive [1] nd lift the hrd drive from the hrd drive rcket [2]. Removing nd instlling components 11

12 Instlling the hrd drive into the hrd drive rcket 1 Align the screw holders on the hrd drive with the screws on the hrd drive rcket. 2 Insert the hrd drive into the hrd drive rcket. 3 Tighten the screws to secure the hrd drive to the hrd drive rcket. 4 Instll the: c hrd drive ssemly ttery se cover 5 Follow the procedure in After working inside your system. Instlling the hrd drive ssemly If the system is shipped with hrd drive ssemly perform the following steps. 1 Insert the hrd drive ssemly into the slot on the computer. 2 Tighten the screws to secure the hrd drive ssemly to the computer. 3 Connect the hrd drive cle to the connector on the hrd drive nd on the system ord. 4 Instll the: ttery se cover 5 Follow the procedures in After working inside your system. Removing the optionl M.2 Solid Stte Drive SSD If the system is shipped with M.2 SSD perform the following steps. 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 To remove the SSD: Remove the screw tht secures the SSD to the computer [1]. Slide nd lift the SSD from the computer [2]. 12 Removing nd instlling components

13 Instlling the optionl M.2 SSD If the system is shipped with M.2 SSD perform the following steps. 1 Insert the SSD into the connector on the computer. 2 Tighten the screw to secure the SSD to the computer. 3 Instll the: ttery se cover 4 Follow the procedure in After working inside your computer. Removing the optionl PCIe SSD If the system is shipped with PCIe SSD perform the following steps. 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 To remove the PCIe SSD: Remove the screws tht secure the SSD rcket to the SSD [1]. Remove the SSD rcket [2]. c Remove the SSD from the computer [3]. d Remove the therml pd from the computer. Instlling the optionl PCIe SSD If the system is shipped with PCIe SSD perform the following steps. 1 Insert the SSD clip into the slot on the computer. 2 Tighten the screw to secure the SSD clip to the computer. Removing nd instlling components 13

14 3 Remove the dhesive nd fix the therml pd to the slot in the computer. 4 Insert the SSD into the connector on the computer. 5 Plce the SSD rcket over the SSD nd tighten the screws to secure it to the computer. 6 Instll the: ttery se cover 7 Follow the procedure in After working inside your computer. Removing the memory module 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 Pull the clips securing the memory module until the memory module pops up [1]. 4 Remove the memory module from the system ord [2]. Instlling the memory module 1 Insert the memory module into the memory module socket until the clips secure the memory module. 2 Instll the: ttery se cover 3 Follow the procedures in After working inside your computer. Removing the WLAN crd 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 To remove the WLAN crd: Remove the screw tht secures the metl rcket to the WLAN crd [1]. Remove the metl rcket [2]. c Disconnect the WLAN cles from the connectors on the WLAN crd [3]. d Unroute the WLAN cles from the routing chnnel. e Remove the WLAN crd from the computer [4]. 14 Removing nd instlling components

15 Instlling the WLAN crd 1 Insert the WLAN crd into the slot on the computer. 2 Route the WLAN cles through the routing chnnel. 3 Connect the WLAN cles to the connectors on the WLAN Crd. 4 Plce the metl rcket nd tighten the screw to secure it to the computer. 5 Instll the: ttery se cover 6 Follow the procedure in After working inside your system. Removing the WWAN crd 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 To remove the WWAN crd: Remove the screw tht secures the WWAN crd [1]. Disconnect the WWAN cles from the connectors on the WWAN crd [2]. c Unroute the WWAN cles from the routing chnnel. d Remove the WWAN crd from the computer [3]. Instlling the WWAN crd 1 Insert the WWAN crd into the slot on the computer. 2 Route the WWAN cles through the routing chnnel. 3 Connect the WWAN cles to the connectors on the WWAN crd. 4 Tighten the screw to secure the WWAN crd to the computer Removing nd instlling components 15

16 5 Instll the: ttery se cover 6 Follow the procedure in After working inside your computer. Removing the dock frme 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WLAN crd WWAN crd 3 To remove the dock frme connectors: Remove the screws tht secure the dock frme to the computer [1]. Remove the screw nd lift the SSD plte from the computer [2, 3]. NOTE: Step 3 is required only if the PCIe SSD crd is removed. c Disconnect the keyord cles [4, 5]. 4 To remove the dock frme: Remove the screw nd lift the metl rcket [1,2]. Disconnect the edp cle [3]. c Remove the screws tht secure the dock frme to the computer [4]. d Lift the dock frme from the computer [5]. 16 Removing nd instlling components

17 Instlling the dock frme 1 Plce the dock frme on the computer nd tighten the screws. 2 Connect the edp cle. 3 Plce the metl rcket nd tighten the screw. 4 Connect the keyord cle. 5 Plce the SSD plte nd tighten the screw to secure it. NOTE: Step 5 is required only if the PCIe SSD crd is removed. 6 Tighten the screws to secure the dock frme to the computer. 7 Instll the: c d e WWAN crd WLAN crd hrd drive ssemly or M.2 SSD or PCIe SSD ttery se cover 8 Follow the procedure in After working inside your system. Removing the power connector port 1 Follow the procedure in Before working inside your computer. 2 Remove the: c se cover ttery dock frme 3 To remove the power connector port: Remove the screw to relese the metl rcket on the power connector port [1]. Lift the metl rcket from the computer [2]. c Disconnect the power connector port cle from the computer [3]. d Remove the power connector port from the computer [4]. Instlling the power connector port 1 Insert the power connector port into the slot on the computer. 2 Plce the metl rcket on the power connector port. 3 Tighten the screw to secure the power connector port to the computer. Removing nd instlling components 17

18 4 Route the power connector port cle through the routing chnnels. 5 Connect the power connector port cle to the connector on the system ord. 6 Instll the: dock frme ttery c se cover 7 Follow the procedure in After working inside your computer. Removing the keyord 1 Follow the procedure in Before working inside your computer. 2 Remove the: se cover ttery 3 Disconnect the keyord cles from the connectors on the touchpd ord [1, 2]. 4 To remove the keyord: Using plstic scrie, lift the keyord trim from the edges to relese it from the keyord [1, 2, 3]. Remove the screws tht secure the keyord to the computer [4]. NOTE: To void dmge to the keyord, gently remove the keyord from the computer. c Lift the keyord from computer [5]. Instlling the keyord 1 Align the keyord with the screw holders on the computer. 2 Tighten the screws to secure the keyord to the computer. 18 Removing nd instlling components

19 3 Align the keyord trim with the ts on the computer nd press it until it clicks into plce 4 Connect the keyord cles to the connectors on the touchpd ord. 5 Instll the: NOTE: If you hve removed the dock frme, then instll the dock frme nd then connect the keyord cles. ttery se cover 6 Follow the procedure in After working inside your system. Removing the disply ssemly 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d se cover ttery WLAN WWAN 3 To remove the disply hinge rckets: Remove the screw tht secures the disply hinge rcket to the computer [1]. Remove the disply hinge rcket from the computer [2]. c Remove the screws tht secure the disply ssemly to the computer [3]. 4 To disconnect disply cle nd remove the disply ssemly: Remove the screw tht secures the disply cle rcket to the computer [1]. Remove the disply cle rcket to ccess the disply cle [2]. c Disconnect the disply cle from the system ord [3]. d Relese the ntenn cles nd disply cle from the routing chnnel [4]. e Remove the screws tht secure the disply ssemly [5]. f Turn over the computer, open the disply, nd lift the disply ssemly from the computer [1] [2]. Removing nd instlling components 19

20 Instlling the disply ssemly 1 Plce the disply ssemly to lign with the screw holders on the computer. 2 Tighten the screws to secure the disply ssemly to the computer. 3 Route the disply cle through the routing chnnel nd route the ntenn cles y pushing it through the hole. 4 Connect the ntenn cles nd disply cle to the connectors. 5 Plce the disply cle rcket over the connector nd tighten the screw to secure the disply cle to the computer. 6 Plce the disply hinge rcket nd tighten the screw to secure it to the computer. 7 Instll the: c d WLAN WWAN ttery se cover 8 Follow the procedure in After working inside your computer. Removing the touchpd utton 1 Follow the procedure in Before working inside your computer. 2 Remove the: c se cover ttery dock frme 3 To remove the touchpd utton: Lift the ltch nd disconnect the touchpd utton cle from the connector [1] [2]. Remove the screws tht secure the touchpd utton [3]. c Lift nd remove the touchpd utton wy from the computer [4]. 20 Removing nd instlling components

21 Instlling the touchpd utton 1 Plce the touchpd utton into the slot on the system ord. 2 Tighten the screws to secure the touchpd utton to the system ord. 3 Connect the touchpd utton cle to the connector on the system ord. 4 Instll the: c dock frme ttery se cover 5 Follow the procedure in After working inside your computer. Removing the optionl SmrtCrd reder ord 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WLAN crd WWAN crd dock frme 3 To remove the SmrtCrd reder ord: Disconnect the SmrtCrd reder ord cle from the USH ord [1, 2]. Peel the cle to relese from the dhesive. c Remove the screws tht secure the SmrtCrd reder ord to the computer [3]. d Lift the SmrtCrd reder ord from the computer [4]. Removing nd instlling components 21

22 Instlling the optionl SmrtCrd reder ord 1 Insert the SmrtCrd reder ord into the slot on the computer. 2 Tighten the screws to secure the SmrtCrd reder ord to the computer. 3 Connect the SmrtCrd reder cle to the connector on the USH ord. 4 Instll the: c d e f dock frme WWAN crd WLAN crd hrd drive ssemly or M.2 SSD or PCIe SSD ttery se cover 5 Follow the procedure in After working inside your computer. Removing the optionl finger print reder ord 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WLAN crd WWAN crd dock frme 3 To remove the finger print reder ord: Disconnect the finger print reder cle from the finger print reder ord [1, 2]. Remove the screw tht secures the finger print reder ord to the computer [3]. c Lift the finger print reder ord from the computer [4]. 22 Removing nd instlling components

23 Instlling the optionl finger print reder ord 1 Insert the finger print reder ord into the slot on the computer. 2 Connect the finger print reder cle to the finger print reder ord. 3 Instll the: c d e f hrd drive ssemly or M.2 SSD or PCIe SSD dock frme WLAN crd WWAN crd ttery se cover 4 Follow the procedure in After working inside your system. Removing the LED ord 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WLAN crd WWAN crd dock frme 3 To remove the LED ord: Disconnect the LED ord cle from the connector on the LED ord [1, 2]. Remove the screw tht secures the LED ord to the computer [3]. c Lift the LED ord from the computer [4]. Removing nd instlling components 23

24 Instlling the LED ord 1 Insert the LED ord into the slot on the computer. 2 Tighten the screw tht secures the LED ord to the computer. 3 Connect the LED ord cle to the connector on the LED ord. 4 Instll the: c d e f dock frme WWAN crd WLAN crd hrd drive ssemly or M.2 SSD or PCIe SSD ttery se cover 5 Follow the procedure in After working inside your computer. Removing the het sink ssemly 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WLAN WWAN dock frme 3 To remove the het sink: Disconnect the fn cle [1]. Remove the screws tht secure the het sink ssemly to the system ord [2, 3, 4, 5, 6]. c Lift the het sink ssemly from the system ord [7]. 24 Removing nd instlling components

25 NOTE: The numer of screws my vry depending upon the computer configurtion. Instlling the het sink ssemly 1 Plce the het sink ssemly on the system ord nd lign it with the screw holders. 2 Tighten the screws to secure the het sink ssemly to the system ord. 3 Connect the fn cle to the connector on the system ord. 4 Instll the: c d e f dock frme WWAN WLAN hrd drive ssemly or M.2 SSD or PCIe SSD ttery se cover 5 Follow the procedure in After working inside your computer. Removing the coin cell ttery 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d se cover ttery hrd drive ssemlyor M.2 SSD or PCIe SSD dock frme 3 To remove the coin cell ttery: Disconnect the coin cell ttery cle from the connector on the system ord [1]. Lift the coin cell ttery to relese it from the dhesive nd remove it from the system ord [2]. Removing nd instlling components 25

26 Instlling the coin cell ttery 1 Plce the coin cell ttery into the slot on the system ord. 2 Connect the coin cell ttery cle to the connector on the system ord. 3 Instll the: c d dock frme hrd drive ssemlyor M.2 SSD or PCIe SSD ttery se cover 4 Follow the procedure in After working inside your computer. Removing the spekers 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f se cover ttery hrd drive ssemly or M.2 SSD or PCIe SSD WWAN WLAN dock frme 3 To remove the speker: Disconnect the speker cle [1]. Lift the ltch nd disconnect the cle [2, 3]. c Remove the screw [4]. d Lift the LED ord [5]. e Remove the speker from the computer [6]. 26 Removing nd instlling components

27 Instlling the spekers 1 Plce the spekers into the slots on the computer. 2 Plce the LED ord. 3 Tighten the screws to secure the LED ord to the computer. 4 Route the speker cle through the retention clips through the routing chnnel. 5 Connect the speker cle to the connector on the system ord. 6 Instll the: c d e f dock frme WLAN WWAN hrd drive ssemly or M.2 SSD or PCIe SSD ttery se cover 7 Follow the procedure in After working inside your computer. Removing the system ord 1 Follow the procedure in Before working inside your computer. 2 Remove the: c d e f g h i j k SIM crd se cover ttery memory hrd drive ssemly or M.2 SSD or PCIe SSD keyord WLAN WWAN dock frme het sink ssemly power connector port 3 Remove the SIM crd try from the computer. 4 To remove the system ord: Lift the ltch nd disconnect the touch pd nd system ord cle from the computer [1, 2]. Disconnect the speker cle nd power connector port cle from the system ord [3]. c Remove the screws tht secures system ord to the computer [4]. d Lift the system ord from the computer [5]. Removing nd instlling components 27

28 Instlling the system ord 1 Align the system ord with the screw holders on the computer. 2 Tighten the screws to secure the system ord to the computer. 3 Connect the speker cle to the connector on the system nd route the cle through the routing chnnels. 4 Connect the power connector nd coin cell ttery cles to the connectors on the system ord: 5 Instll the: power connector port dock frme c WLAN d het sink ssemly e WWAN f hrd drive ssemly or M.2 SSD or PCIe SSD g keyord h memory module i ttery j se cover k SIM crd 6 Follow the procedure in After working inside your computer. Removing the plmrest 1 Follow the procedure in Before working inside your computer. 2 Remove the: SIM crd se cover c ttery d memory e hrd drive ssemly or M.2 SSD or PCIe SSD f keyord g WLAN h WWAN i dock frme j het sink ssemly k power connector port l system ord 3 The plmrest is the remining component, fter removing ll the components. 28 Removing nd instlling components

29 Instlling the plmrest 1 Align the plmrest on the computer. 2 Instll the: system ord power connector port c dock frme d WLAN e het sink ssemly f WWAN g hrd drive ssemly or M.2 SSD or PCIe SSD h keyord i memory module j ttery k se cover l SIM crd 3 Follow the procedure in After working inside your computer. Removing nd instlling components 29

30 3 System setup options NOTE: Depending on the computer nd its instlled devices, the items listed in this section my or my not pper. Topics: Boot Sequence Nvigtion keys System Setup overview Accessing System Setup Generl screen options System Configurtion screen options Video screen options Security screen options Secure Boot screen options Intel Softwre Gurd Extensions screen options Performnce screen options Power Mngement screen options POST Behvior screen options Virtuliztion support screen options Wireless screen options Mintennce screen options System Log screen options Updting the BIOS in Windows System nd setup pssword Boot Sequence Boot Sequence llows you to ypss the System Setup defined oot device order nd oot directly to specific device (for exmple: opticl drive or hrd drive). During the Power-on Self Test (POST), when the Dell logo ppers, you cn: Access System Setup y pressing F2 key Bring up the one-time oot menu y pressing F12 key The one-time oot menu displys the devices tht you cn oot from including the dignostic option. The oot menu options re: Removle Drive (if ville) STXXXX Drive NOTE: XXX denotes the SATA drive numer. Opticl Drive (if ville) SATA Hrd Drive (if ville) Dignostics NOTE: Choosing Dignostics, will disply the epsa dignostics screen. 30 System setup options

31 The oot sequence screen lso displys the option to ccess the System Setup screen. Nvigtion keys NOTE: For most of the System Setup options, chnges tht you mke re recorded ut do not tke effect until you restrt the system. Keys Up rrow Down rrow Enter Spcer T Nvigtion Moves to the previous field. Moves to the next field. Selects vlue in the selected field (if pplicle) or follow the link in the field. Expnds or collpses drop down list, if pplicle. Moves to the next focus re. NOTE: For the stndrd grphics rowser only. Esc Moves to the previous pge until you view the min screen. Pressing Esc in the min screen displys messge tht prompts you to sve ny unsved chnges nd restrts the system. System Setup overview System Setup llows you to: Chnge the system configurtion informtion fter you dd, chnge, or remove ny hrdwre in your computer. Set or chnge user-selectle option such s the user pssword. Red the current mount of memory or set the type of hrd drive instlled. Before you use System Setup, it is recommended tht you write down the System Setup screen informtion for future reference. CAUTION: Unless you re n expert computer user, do not chnge the settings for this progrm. Certin chnges cn cuse your computer to work incorrectly. Accessing System Setup 1 Turn on (or restrt) your computer. 2 After the white Dell logo ppers, press F2 immeditely. The System Setup pge is displyed. NOTE: If you wit too long nd the operting system logo ppers, wit until you see the desktop. Then, shut down or restrt your computer nd try gin. NOTE: After the Dell logo ppers, you cn lso press F12 nd then select BIOS setup. Generl screen options This section lists the primry hrdwre fetures of your computer. Option Description System Informtion System Informtion: Displys BIOS Version, Service Tg, Asset Tg, Ownership Tg, Ownership Dte, Mnufcture Dte, nd the Express Service Code. Memory Informtion: Displys Memory Instlled, Memory Aville, Memory Speed, Memory Chnnels Mode, Memory Technology, DIMM A Size, DIMM B Size. System setup options 31

32 Option Bttery Informtion Description Processor Informtion: Displys Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum Clock Speed, Mximum Clock Speed, Processor L2 Cche, Processor L3 Cche, HT Cple, nd 64-Bit technology. Device Informtion: Displys Primry Hrd Drive, SATA-0, M.2PCIe SSD-0, Dock esata Device, LOM MAC Address, Video Controller, Video BIOS Version, Video Memory, Pnel Type, Ntive Resolution, Audio Controller, WiFi Device, WiGig Device, Cellulr Device, Bluetooth Device. Displys the ttery sttus nd the type of AC dpter connected to the computer. Boot Sequence Boot Sequence Allows you to chnge the order in which the computer ttempts to find n operting system. The options re: UEFI: LITEON IT L8H-128V2G-11M GB Boot List Options Allows you to chnge the oot list option: Legcy UEFI (enled y defult) Advnced Boot Options This option llows you the legcy option ROMs to lod. By defult, the Enle Legcy Option ROMs is disled. Dte/Time Allows you to chnge the dte nd time. System Configurtion screen options Option Integrted NIC Description Allows you to configure the integrted network controller. The options re: Disled Enled Enled w/pxe: This option is enled y defult. Prllel Port Allows you to configure the prllel port on the docking sttion. The options re: Disled AT: This option is enled y defult. PS2 ECP Seril Port Allows you to configure the integrted seril port. The options re: Disled COM1: This option is enled y defult. COM2 COM3 COM4 SATA Opertion Allows you to configure the internl SATA hrd-drive controller. The options re: Disled AHCI 32 System setup options

33 Option Drives Description RAID On: This option is enled y defult. Allows you to configure the SATA drives on ord. All drives re enled y defult. The options re: SATA-0 SATA-1 SATA-2 M.2 PCIe SSD-0 SMART Reporting This field controls whether hrd drive errors for integrted drives re reported during system strtup. This technology is prt of the SMART (Self Monitoring Anlysis nd Reporting Technology) specifiction. This option is disled y defult. Enle SMART Reporting USB Configurtion This field configures the integrted USB controller. If Boot Support is enled, the system is llowed to oot ny type of USB Mss Storge Devices (HDD, memory key, floppy). If USB port is enled, device ttched to this port is enled nd ville for OS. If USB port is disled, the OS cnnot see ny device ttched to this port. The options re: Enle USB Boot Support: This option is enled y defult. Enle Externl USB Port: This option is enled y defult. USB PowerShre Audio This field configures the USB PowerShre feture ehvior. This option llows you to chrge externl devices using the stored system ttery power through the USB PowerShre port. This field enles or disles the integrted udio controller. By defult, the Enle Audio option is selected. The options re: Enle Microphone: This option is enled y defult. Enle Internl Speker: This option is enled y defult. Keyord Illumintion This field lets you choose the operting mode of the keyord illumintion feture. The keyord rightness level cn e set from 0% to 100%. The options re: Disled Dim Bright: This option is enled y defult. Keyord Bcklight with AC Keyord Bcklight Timeout on AC The Keyord Bcklight with AC option does not ffect the min keyord illumintion feture. Keyord Illumintion will continue to support the vrious illumintion levels. This field hs n effect when the cklight is enled. This feture defines the timeout vlue for the keyord cklight when AC dpter is plugged into the system. The options re: 5 seconds: This option is enled y defult. 10 seconds 15 seconds 30 seconds 1 minute 5 minute System setup options 33

34 Option Keyord Bcklight Timeout on Bttery Touchscreen Description 15 minute Never This feture defines the timeout vlue for the keyord cklight when system is running only on ttery power. 5 seconds: This option is enled y defult. 10 seconds 15 seconds 30 seconds 1 minute 5 minute 15 minute Never This option controls to enled or disled the touchscreen. NOTE: Touchscreen option is ville only if the computer is touch version. Unotrusive Mode Miscellneous Devices This option, when enled, pressing Fn+F7 turns off ll light nd sound emissions in the system. To resume norml opertion, press Fn+F7 gin. This option is disled y defult. Allows you to enle or disle the following devices: Enle Cmer: This option is enled y defult. SD Crd Red Only Enle Hrd Drive Free Fll Protection: This option is enled y defult. Enle Medi Crd Disle Medi Crd NOTE: All devices re enled y defult. Video screen options Option LCD Brightness Description Allows you to set the disply rightness depending up on the power source (On Bttery nd On AC). NOTE: The video setting will e visile only when video crd is instlled into the system. Security screen options Option Admin Pssword Description Allows you to set, chnge, or delete the dministrtor (dmin) pssword. NOTE: You must set the dmin pssword efore you set the system or hrd drive pssword. Deleting the dmin pssword utomticlly deletes the system pssword nd the hrd drive pssword. NOTE: Successful pssword chnges tke effect immeditely. Defult setting: Not set System Pssword Allows you to set, chnge or delete the system pssword. 34 System setup options

35 Option Description NOTE: Successful pssword chnges tke effect immeditely. Defult setting: Not set Mini Crd SSD Pssword Allows you to set, chnge or delete the Mini Crd SSD Pssword. NOTE: Successful pssword chnges tke effect immeditely. Defult setting: Not set Strong Pssword Allows you to enforce the option to lwys set strong psswords. Defult Setting: Enle Strong Pssword is not selected. NOTE: If Strong Pssword is enled, Admin nd System psswords must contin t lest one uppercse chrcter, one lowercse chrcter nd e t lest 8 chrcters long. Pssword Configurtion Pssword Bypss Allows you to determine the minimum nd mximum length of Administrtor nd System psswords. Allows you to enle or disle the permission to ypss the System nd the Internl HDD pssword, when they re set. The options re: Disled Reoot ypss Defult setting: Disled Pssword Chnge Allows you to enle the disle permission to the System nd Hrd Drive psswords when the dmin pssword is set. Defult setting: Allow Non-Admin Pssword Chnges is selected. Non-Admin Setup Chnges UEFI Cpsule Firmwre Updte TPM 1.2 Security Allows you to determine whether chnges to the setup options re llowed when n Administrtor Pssword is set. If disled the setup options re locked y the dmin pssword. This option controls whether the system llows the BIOS updtes through UEFI cpsule updte pckges. This option is disled y defult. Allows you to enle the Trusted Pltform Module (TPM) during POST. The options re: TPM On (enled y defult) Cler PPI Bypss for Enled Commnds PPI Bypss for Disled Commnds Disled Enled Computrce Allows you to ctivte or disle the optionl Computrce softwre The options re: Dectivte Disle Activte NOTE: The Activte nd Disle options will permnently ctivte or disle the feture nd no further chnges will e llowed System setup options 35

36 Option Description Defult setting: Dectivte CPU XD Support Allows you to enle the Execute Disle mode of the processor. Enle CPU XD Support (defult) OROM Keyord Access Allows you to set n option to enter the Option ROM Configurtion screens using hotkeys during oot. The options re: Enle One Time Enle Disle Defult setting: Enle Admin Setup Lockout Allows you to prevent users from entering the setup when n Administrtor pssword is set. Defult Setting: Enle Admin Setup Lockout is not selected. Secure Boot screen options Option Secure Boot Enle Description This option enles or disles the Secure Boot feture. Disled Enled Defult setting: Enled. Expert Key Mngement Allows you to mnipulte the security key dtses only if the system is in Custom Mode. The Enle Custom Mode option is disled y defult. The options re: PK KEK d dx If you enle the Custom Mode, the relevnt options for PK, KEK, d, nd dx pper. The options re: Sve to File Sves the key to user-selected file Replce from File Replces the current key with key from user-selected file Append from File Adds key to the current dtse from user-selected file Delete Deletes the selected key Reset All Keys Resets to defult setting Delete All Keys Deletes ll the keys NOTE: If you disle the Custom Mode, ll the chnges mde will e ersed nd the keys will restore to defult settings. 36 System setup options

37 Intel Softwre Gurd Extensions screen options Option Intel SGX Enle Description This field specifies you to provide secured environment for running code/storing sensitive informtion in the context of the min OS. The options re: Disled Enled Defult setting: Disled Enclve Memory Size This option sets SGX Enclve Reserve Memory Size. The options re: 32 MB 64 MB 128 MB Performnce screen options Option Multi Core Support Description This field specifies whether the process hs one or ll cores enled. The performnce of some pplictions improves with the dditionl cores. This option is enled y defult. Allows you to enle or disle multi-core support for the processor. The instlled processor supports two cores. If you enle Multi Core Support, two cores re enled. If you disle Multi Core Support, one core is enled. Enle Multi Core Support Defult setting: The option is enled. Intel SpeedStep Allows you to enle or disle the Intel SpeedStep feture. Enle Intel SpeedStep Defult setting: The option is enled. C-Sttes Control Allows you to enle or disle the dditionl processor sleep sttes. C sttes Defult setting: The option is enled. Intel TuroBoost Allows you to enle or disle the Intel TuroBoost mode of the processor. Enle Intel TuroBoost Defult setting: The option is enled. Hyper-Thred Control Allows you to enle or disle the Hyper-Threding in the processor. Disled Enled Defult setting: Enled. System setup options 37

38 Power Mngement screen options Option AC Behvior Description Allows you to enle or disle the computer from turning on utomticlly when n AC dpter is connected. Defult setting: Wke on AC is not selected. Auto On Time Allows you to set the time t which the computer must turn on utomticlly. The options re: Disled Every Dy Weekdys Select Dys Defult setting: Disled USB Wke Support Allows you to enle USB devices to wke the system from Stndy. NOTE: This feture is only functionl when the AC power dpter is connected. If the AC power dpter is removed during Stndy, the system setup removes power from ll the USB ports to conserve ttery power. Enle USB Wke Support Defult setting: The option is disled. Wireless Rdio Control Allows you to enle or disle the feture tht utomticlly switches from wired or wireless networks without depending on the physicl connection. Control WLAN Rdio Control WWAN Rdio Defult setting: The option is disled. Wke on LAN/ WLAN Allows you to enle or disle the feture tht powers on the computer from the Off stte when triggered y LAN signl. Disled LAN Only WLAN Only LAN or WLAN Defult setting: Disled Block Sleep This option lets you lock entering to sleep (S3 stte) in operting system environment. Block Sleep (S3 stte) Defult setting: This option is disled Pek Shift Dock Support on Bttery This option enles you to minimize the AC power consumption during the pek power times of dy. After you enle this option, your system runs only in ttery even if the AC is ttched. This option llows you to use the docking sttion when AC power is sent ut only when the ttery is ove certin chrge percentge. The percentge my chnge per ttery nd per pltform. 38 System setup options

39 Option Description Dock Support on Bttery Defult setting: Disled Advnced Bttery Chrge Configurtion This option enles you to mximize the ttery helth. By enling this option, your system uses the stndrd chrging lgorithm nd other techniques, during the non-work hours to improve the ttery helth. Disled Defult setting: Disled Primry Bttery Chrge Configurtion Allows you to select the chrging mode for the ttery. The options re: Adptive Stndrd Fully chrges your ttery t stndrd rte. ExpressChrge The ttery chrges over shorter period of time using Dell s fst chrging technology. This option is enled y defult. Primrily AC use Custom If Custom Chrge is selected, you cn lso configure Custom Chrge Strt nd Custom Chrge Stop. NOTE: All chrging mode my not e ville for ll the tteries. To enle this option, disle the Advnced Bttery Chrge Configurtion option. POST Behvior screen options Option Adpter Wrnings Description Allows you to enle or disle the system setup (BIOS) wrning messges when you use certin power dpters. Defult setting: Enle Adpter Wrnings Keypd (Emedded) Allows you to choose one of two methods to enle the keypd tht is emedded in the internl keyord. Fn Key Only: This option is enled y defult. By Numlock NOTE: When setup is running, this option hs no effect. Setup works in Fn Key Only mode. Mouse/Touchpd Allows you to define how the system hndles mouse nd touch pd input. The options re: Seril Mouse PS2 Mouse Touchpd/PS-2 Mouse: This option is enled y defult. Numlock Enle Allows you to enle the Numlock option when the computer oots. Enle Network. This option is enled y defult. Fn Key Emultion Allows you to set the option where the Scroll Lock key is used to simulte the Fn key feture. Enle Fn Key Emultion (defult) System setup options 39

40 Option Fn Lock Options Description Allows you to let hot key comintions Fn + Esc toggle the primry ehvior of F1 F12, etween their stndrd nd secondry functions. If you disle this option, you cnnot toggle dynmiclly the primry ehvior of these keys. The ville options re: Fn Lock. This option is selected y defult. Lock Mode Disle/Stndrd Lock Mode Enle/Secondry MEBx Hotkey Allows you to specify whether the MEBx Hotkey function should enle, during the system oot. Defult Setting: Enle MEBx Hotkey Fstoot Allows you to speed up the oot process y ypssing some of the comptiility steps. The options re: Miniml Thorough (defult) Auto Extended BIOS POST Time Allows you to crete n dditionl preoot dely. The options re: 0 seconds. This option is enled y defult. 5 seconds 10 seconds Virtuliztion support screen options Option Virtuliztion Description Allows you to enle or disle the Intel Virtuliztion Technology. Enle Intel Virtuliztion Technology (defult). VT for Direct I/O Enles or disles the Virtul Mchine Monitor (VMM) from utilizing the dditionl hrdwre cpilities provided y Intel Virtuliztion technology for direct I/O. Enle VT for Direct I/O - enled y defult. Trusted Execution This option specifies whether Mesured Virtul Mchine Monitor (MVMM) cn utilize the dditionl hrdwre cpilities provided y Intel Trusted Execution Technology. The TPM Virtuliztion Technology, nd Virtuliztion technology for direct I/O must e enled to use this feture. Trusted Execution - disled y defult. Wireless screen options Option Wireless Switch Description Allows to set the wireless devices tht cn e controlled y the wireless switch. The options re: WWAN GPS (on WWAN Module) WLAN/WiGig Bluetooth 40 System setup options

41 Option Description All the options re enled y defult. NOTE: For WLAN nd WiGig enle or disle controls re tied together nd they cnnot e enled or disled independently. Wireless Device Enle Allows you to enle or disle the internl wireless devices. WWAN/GPS WLAN/WiGig Bluetooth All the options re enled y defult. Mintennce screen options Option Service Tg Asset Tg BIOS Downgrde Dt Wipe Description Displys the Service Tg of your computer. Allows you to crete system sset tg if n sset tg is not lredy set. This option is not set y defult. This controls flshing of the system firmwre to previous revisions. This field llows users to erse the dt securely from ll internl storge devices. The following is list of devices ffected: Internl HDD Internl SDD Internl msata Internl emmc WARNING: Selecting this option results in permnent dt loss nd this ction cnnot e reversed. BIOS Recovery This field llows you to recover from certin corrupted BIOS conditions from recover file on the user primry hrd drive or n externl USB key. BIOS Recovery from Hrd Drive (enled y defult) System Log screen options Option BIOS Events Therml Events Description Allows you to view nd cler the System Setup (BIOS) POST events. Allows you to view nd cler the System Setup (Therml) events. Power Events Allows you to view nd cler the System Setup (Power) events. Updting the BIOS in Windows It is recommended to updte your BIOS (System Setup), when you replce the system ord or if n updte is ville. For lptops, ensure tht your computer ttery is fully chrged nd connected to power outlet System setup options 41

42 NOTE: If BitLocker is enled, it must e suspended prior to updting the system BIOS, nd then re-enled fter the BIOS updte is completed. 1 Restrt the computer. 2 Go to Dell.com/support. Enter the Service Tg or Express Service Code nd click Sumit. Click Detect Product nd follow the instructions on screen. 3 If you re unle to detect or find the Service Tg, click Choose from ll products. 4 Choose the Products ctegory from the list. NOTE: Choose the pproprite ctegory to rech the product pge 5 Select your computer model nd the Product Support pge of your computer ppers. 6 Click Get drivers nd click Drivers nd Downlods. The Drivers nd Downlods section opens. 7 Click Find it myself. 8 Click BIOS to view the BIOS versions. 9 Identify the ltest BIOS file nd click Downlod. 10 Select your preferred downlod method in the Plese select your downlod method elow window, click Downlod File. The File Downlod window ppers. 11 Click Sve to sve the file on your computer. 12 Click Run to instll the updted BIOS settings on your computer. Follow the instructions on the screen. NOTE: It is recommended not to updte the BIOS version for more thn three revisions. For exmple: If you wnt to updte the BIOS from 1.0 to 7.0, then instll version 4.0 first nd then instll version 7.0. System nd setup pssword You cn crete system pssword nd setup pssword to secure your computer. Pssword type System pssword Setup pssword Description Pssword tht you must enter to log on to your system. Pssword tht you must enter to ccess nd mke chnges to the BIOS settings of your computer. CAUTION: The pssword fetures provide sic level of security for the dt on your computer. CAUTION: Anyone cn ccess the dt stored on your computer if it is not locked nd left unttended. NOTE: System nd setup pssword feture is disled. Assigning system pssword nd setup pssword You cn ssign new System Pssword only when the sttus is in Not Set. To enter the system setup, press F2 immeditely fter power-on or re-oot. 1 In the System BIOS or System Setup screen, select Security nd press Enter. The Security screen is displyed. 2 Select System Pssword nd crete pssword in the Enter the new pssword field. Use the following guidelines to ssign the system pssword: A pssword cn hve up to 32 chrcters. The pssword cn contin the numers 0 through System setup options