MINI-BEAM SME312 Expert Series

Transcription

1 M-M M32 xpert eries nstruction Manual Microprocessor-ased TH Mode Photoelectric ensors U.. patent(s) issued or pending TH-mode sensors in the popular M-M package asy push-button programming automatically adjusts sensitivity to optimal setting Multiple sensing modes include retroreflective, polarized retro, clear object detection, diffuse, divergent, and convergent, plus glass and plastic fiber optic models Fast, 5 microsecond (.5 millisecond) output response ipolar P (sinking)/pp (sourcing) outputs asy output programming eliminates the need for Light or Dark operate selection eparate TH input allows remote programming by an external device, such as a switch or process controller LD status indications for received signal strength (using anner's D function), power O, and output state reen tability indicator flashes when received signal level approaches the switching threshold, also indicates Power O ntegral 2 m (6.5 ft) cable or 5-pin uro-style quick-disconnect (QD) connector, depending on model; 9 m (3 ft) cable models are also available WR: ot To e Used for Personnel Protection ever use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Retroreflective Models Model ensing Mode Range or Focus 2 upply Voltage Output Type M32LV Retroreflective, Visible red, 65 nm 5 m (5 ft) M32LP Polarized retroreflective, Visible red, 65 nm mm to 3 m (.4 in to ft) M32LP Polarized retroreflective, Visible red, 65 nm (clear object) m (3.3 ft) with supplied reflector V dc to 3 V dc ipolar P/PP ls Model ensing Mode Range or Focus upply Voltage Output Type M32D Diffuse, nfrared, 88 nm 38 mm (5 in) M32DV Diffuse, Visible red, 65 nm mm (43 in) V dc to 3 V dc ipolar P/PP M32W Divergent Diffuse, nfrared, 88 nm 3 mm (5 in) tandard 2 m (6.5 ft) cable models are listed. To order the 9 m (3 ft) cable model, add suffix W/3 to the model number (for example, M32LV W/3.) To order the 5-pin uro-style QD models, add suffix QD (for example, M32LVQD). Models with a QD connector require a mating cable. 2 ensing ranges vary according to the efficiency and reflective area of the retroreflector(s) used. (Retroreflective tape is not recommended for use with lear Object Detection models.) ee ccessories and the anner ngineering catalog for more information. Original Document 5524 Rev. 3 July

2 M-M M32 xpert eries onvergent Models Model ensing Mode Range or Focus pot ize at Focus upply Voltage Output Type M32V onvergent, Visible red, 65 nm 6 mm (.65 in).3 mm (.5 in) M32V2 onvergent, Visible red, 65 nm 43 mm (.7 in) 3. mm (.2 in) M32V onvergent, Visible green, 525 nm 6 mm (.65 in). mm (.4 in) V dc to 3 V dc ipolar P/PP M32V M32VW onvergent, Visible blue, 475 nm onvergent, Visible white, nm 6 mm (.65 in).8 mm (.7 in) lass Fiber Optic Models Model ensing Mode Range or Focus upply Voltage Output Type M32F lass Fiber Optic, 88 nm infrared M32FV lass Fiber Optic, Visible red, 65 nm M32FV lass Fiber Optic, Visible green, 525 nm Range varies by sensing mode and fiber optics used V dc to 3 V dc ipolar P/PP M32FV lass Fiber Optic, Visible blue, 475 nm M32FVW lass Fiber Optic, Visible white, nm Plastic Fiber Optic Models Model ensing Mode Range or Focus upply Voltage Output Type M32FP Plastic Fiber Optic, Visible red, 65 nm M32FP M32FP Plastic Fiber Optic, Visible green, 525 nm Plastic Fiber Optic, Visible blue, 475 nm Range varies by sensing mode and fiber optics used V dc to 3 V dc ipolar P/PP M32FPW Plastic Fiber Optic, Visible white, nm Overview mber output indicator LD i-color green/red indicator LD M-M xpert is a complete family of sensors, all housed in the popular, robust and compact rectangular housing. Their large push button and easy-to-see indicators provide easy configuration, alignment, and monitoring during use. Retroreflective and Polarized Retroreflective Mode models are excellent for sensing relatively small items where opposed-mode sensing is not possible. They are recommended for relatively clean environments where high excess gain is not required. Polarized models filter out unwanted reflections. Polarized Retroreflective Mode lear Object Detection models reliably detect the presence of clear objects. models are excellent for sensing objects of adequate size and reflectivity at short range. Divergent models are useful for sensing small items and translucent or transparent materials at close range. The M32DV sensors effectively sense specular surfaces like semi-conductor wafers, disk drive media, glass and machined surfaces. The collimated optics of the M32DV also permits the sensor to be mounted against clear container walls, view ports and other types of optical feed-throughs. onvergent Mode models are a good choice for counting adjacent radiused objects and for accurate position sensing. lue, green and white beam models are recommended for color mark sensing. lass Fiber Optic models are an excellent option for sensing in tight or otherwise inaccessible areas. Fibers withstand vibration and shock and are immune to electrical noise. lass fibers withstand high temperatures, extreme moisture and corrosive materials. lass fibers are not recommended for applications requiring bending or repeated flexing (see plastic fiber models). Visible beam models are recommended for color mark sensing Tel: P/ 5524 Rev.

3 M-M M32 xpert eries Plastic Fiber Optic models are an excellent option for sensing in tight or otherwise inaccessible areas. Fibers withstand vibration and shock and are immune to electrical noise. Plastic fibers function well at temperatures from 3 to +7 ( 2 F to +58 F), and stand up to repeated flexing. Most are easy to shorten in the field, for custom installations. Plastic fibers are not recommended for severe environments (see glass fiber models). Plastic fiber optic sensors are recommended for color mark sensing. tatus ndicators ormal sensor operation is called RU mode. ensor configuration (setting the sensitivity threshold and selecting output O and OFF conditions) is performed in TH mode. The two LD indicators (bi-color green/red and amber) have distinct roles in the two operation modes. f contrast is marginal, the bi-color indicator will flash green to indicate instability. f this occurs, reconfigure or realign the sensor, or clean the sensor or fiber lenses. The ignal trength indicator is anner s exclusive D (lignment ndicating Device). ts pulse rate increases as the received light signal strength increases (during programming). This feature simplifies accurate alignment during TH mode, and gives a relative indication of sensing contrast between the light and dark conditions. LD RU Mode TH Mode olid green Flashing green Power is on ensed light level is approaching sensing threshold 3 olid red ensor sees its own modulated light source; pulse rate is proportional to the received light signal strength 4 mber on Outputs conducting Ready to TH output O condition mber off Outputs not conducting Ready to TH output OFF condition Remote onfiguration The remote function can be used to configure the sensor remotely or to disable the push button for security. onnect the gray wire of the sensor to ground ( V dc), with a remote programming switch connected between them. Pulse the remote line according to the diagrams in the configuration procedures. The length of the individual programming pulses is equal to the value T where:.4 seconds T.8 seconds nstallation Wiring Diagrams abled Models QD Models bn bu wh bk gy Load Load + -3V dc Remote Teach bn bu wh bk gy Load Load + -3V dc Remote Teach 3 This is the tability indicator, which signals when maintenance, realignment, or reconfiguration is needed during RU mode. 4 The faster the pulse rate, the stronger the light signal. P/ 5524 Rev. - Tel:

4 M-M M32 xpert eries lass Fiber nstallation Retaining lip O-ring. nstall the O-ring (supplied with the fiber) on each fiber end, as shown in the drawing. 2. While pressing the fiber ends firmly into the ports on the sensor front, slide the U-shaped retaining clip (supplied with the sensor) into the slot in the sensor's barrel, until it snaps into place. Plastic Fiber nstallation ensor Face ripper Unlock Lock dapters for.25- and.5-mm fibers Trimmed fiber control ends. With supplied fiber cutter, make a clean cut at the control ends of fibers. 2. Unlock the fiber gripper as shown in the drawing. 3. pply appropriate fiber adaptors to the fiber, if needed. 4. ently insert the prepared fiber ends into the ports as far as they will go. 5. lide the fiber gripper back to lock, as shown in the drawing. Plastic fiber receiver port Plastic fiber emitter port tatic Teach 2nd Taught ondition Output OFF ensor positions threshold between taught conditions st Taught ondition Output O The two sensing conditions may be presented in either order. The condition presented first is the condition for which the output will energize (the Output O target). ensitivity is automatically set (and optimized) when teaching the sensor the O and OFF conditions. When the push button is clicked, the sensor samples each sensing condition and registers it into memory. fter the second sensing condition is registered, the M-M xpert automatically sets the sensitivity to the optimum value for the application, and then returns to RU mode. Push button (.4 seconds lick.8 seconds); Remote line (.4 seconds T.8 seconds). ccess TH mode. Method ction Result Via push button Via remote line Press and hold push button until the bi-color (green/ red) indicator begins to flash red, or turns OFF. o action required; sensor is ready for st sensing condition. Push button method only: The amber LD is on. The red LD pulses to indicate relative received signal strength. The sensor is ready for the output O condition Tel: P/ 5524 Rev.

5 M-M M32 xpert eries 2. Teach the first sensing condition. Method ction Result Via push button Via remote line Present the first sensing condition and click the push button. Present the first sensing condition and single-pulse the remote line. The amber LD is off. The red LD pulses to indicate relative signal strength. The sensor registers the output O condition and is ready for the output OFF condition. 3. Teach the second sensing condition and return to RU mode. Method ction Result Via push button Via remote line Present the second sensing condition and click the push button. Present the second sensing condition and single-pulse the remote line. f the teach is accepted the green LD is on (or flashes if the signal is close to the switching threshold) and the amber LD is off until the sensing condition changes; the sensor registers the output OFF condition, positions the threshold, and returns to RU mode. f the teach is not accepted, the amber LD is on and the red LD pulses to indicate the relative received signal strength. The sensor returns to its wait state and is ready for the first sensing condition. OT: The sensor returns to RU mode if the first TH condition is not registered within 9 seconds. TH mode may be cancelled before either the first or second condition by holding the push button depressed for more than two seconds. nabling or Disabling the Push utton n addition to its programming function, the remote line may be used to disable the push buttons for security. Disabling the push buttons prevents undesired tampering with the sensor configuration settings.. onnect the sensor s gray wire. 2. Four-pulse the remote line to enable or disable the push button. The sensor toggles between enable and disable settings and returns to RU mode. P/ 5524 Rev. - Tel:

6 M-M M32 xpert eries pecifications upply Voltage and urrent V dc to 3 V dc (% maximum ripple) at less than 45 m, exclusive of load upply Protection ircuitry Protected against reverse polarity and transient voltages djustments Push-button TH mode sensitivity setting; remote TH mode input is provided ndicators Two LDs: amber and bi-color green/red onstruction Reinforced thermoplastic polyester housing, totally encapsulated, o- ring seal, acrylic lenses, and stainless steel screws. Required Overcurrent Protection WR: lectrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via urrent Limiting, lass 2 Power upply. upply wiring leads < 24 W shall not be spliced. For additional product support, go to upply Wiring (W) Required Overcurrent Protection (mps) onnections PV-jacketed 5-conductor 2 m (6.5 ft) or 9 m (3 ft) unterminated cable, or 5-pin uro-style quick-disconnect (QD) fitting are available. QD cables are ordered separately. pplication otes The first condition presented during TH mode becomes the output O condition. Output onfiguration ipolar: One current sourcing (PP) and one current sinking (P) open-collector transistor Output Rating 5 m maximum each output at 25, derated to m at 7 (derate m per ) Off-state leakage current: less than 5 μ at 3 V dc O-state saturation current: less than V at m; less than.5 V at 5 m Output Protection ircuitry Protected against false pulse on power-up and continuous overload or short-circuit of outputs Output Response Time ensors will respond to either a light or a dark signal of 5 microseconds or longer duration, khz max. Repeatability microseconds (all models) OT: second delay on power-up; outputs do not conduct during this time. Rating Meets M standards, 2, 3, 3, 4, 4, 6, 2, and 3; P67 Operating onditions Temperature: 2 to +7 ( 4 to +58 F) Max. Relative Humidity: 9% at 5 (non-condensing) 3.5 Dimensions abled Models (uffix, L, PD, R, RL, RPD, LV, LV, LP, LP, D,, 2, V, V2, V, V2, V, V2, VW ) 3.7 mm (.2 ) 24. mm (.95 ) 3.2 mm (.3 ) 2.2 mm (.48 ) 3 mm dia learance (2) Divergent ls (uffix DZ and W) 3 mm dia learance (2) ezel 8. mm (.7 ) M8 5 mm Thread (Mounting nut supplied) 2 m (6.5 ) able Mounting peg (6.3 mm dia 2.5 mm) 9. mm (.75 ) 39. mm (.54 ) 3.2 mm (.52 ) 53.3 mm (2. ) 27.4 mm (.8 ) Tel: P/ 5524 Rev.

7 M-M M32 xpert eries lass Fiber Models (uffix F, FV, FV, FV, FVW) Plastic Fiber Models (uffix FP, FP, FP, FPH, FPW) 3.2 mm (.3 ) 2.2 mm (.48 ) M8 x x 9 mm Thread (Mounting ut upplied) Fiber Optic Fitting 3.7 mm (.2 ) 2 m (6.5 ) able 24. mm (.95 ) 3 mm dia clearance (2) Fiber Optic Fitting 57.5 mm (2.27") Mounting Peg (6.3 mm dia 2.5 mm) 9. mm (.75 ) 22.3 mm (.88 ) 3.2 mm (.23") 42. mm (.66 ) 6.2 mm (.64 ) QD Models 2 mm Thread Quick-disconnect 2. mm (.79 ) Performance urves Retroreflective xcess ain eam Pattern xcess ain eam Pattern M32LV Retroreflective Mode 5 mm 5 mm M32LV Retroreflective Mode 3." 2."."." 2." M32LP Retroreflective Mode 6 mm 4 mm 2 mm 2 mm 4 mm M32LP Retroreflective Mode 2..6".8".8".6". m.33'. m.33'. m 3.3' m 33' m 3' 2 m 6' 3 m 9' 4 m 2' 5 m 5' 3.". m.3'. m.3' m 3' m 3' 6 mm.6 m 2'.2 m 4'.8 m 6' 2.4 m 8' 3. m ' 2.. m.33' with RT-7777 Reflector. m.33' with RT-22 Reflector M32LP Retroreflective Mode. m 3.3'. m 33' 5 mm mm 5 mm 5 mm mm 5 mm M32LP Retroreflective Mode with RT-22 Reflector.5 m.7' m 3.3' with RT-7777 Reflector.5 m 5' 2 m 6.6' 2.5 m 8.3' 6" 6" P/ 5524 Rev. - Tel:

8 M-M M32 xpert eries Diffuse Diffuse-mode performance based on 9% reflectance white test card. xcess ain eam Pattern xcess ain eam Pattern 5 mm mm 5 mm 5 mm M32D.6"... M32DV 2 mm 5 mm mm 5 mm 5 mm M32DV.8".6"... mm 5 mm 3." 5 mm 6." 2 9." 3 mm 2." 3 5."..6" mm. mm 4." mm mm mm 5 mm." 5 mm 2." 3." mm 4."..6" 2 mm.8" 5." mm. mm. M32W mm mm 22.5 mm 5. mm 7.5 mm 7.5 mm 5. mm 22.5 mm M32W." 5 mm 2." 3." mm 4." 5.".9".6".3".3".6".9" onvergent xcess ain eam Pattern xcess ain eam Pattern mm.4 " mm. M32V onvergent Mode mm mm 3. mm 2. mm. mm. mm 2. mm 3. mm M32V onvergent Mode 7.5 mm.3 " 5 mm.6 " 22.5 mm.9 " 3 mm.2 " 37.5 mm.5 ".2 ".8 ".4 ".4 ".8 ".2 " mm.4 " mm. M32V2 onvergent Mode mm mm 3. mm 2. mm. mm. mm 2. mm 3. mm M32V2 onvergent Mode " 5 mm 3" mm 5"..8"...8".. mm.4 in mm.4 in M32FP M32FP M32FPW Plastic Fiber mm.4 in PT46U Fiber mm 4 in 3. mm 2. mm. mm. mm 2. mm 3. mm M32V M32V M32VW onvergent Mode 7.5 mm.3" 5 mm.6" 22.5 mm.9" 3 mm mm.5"..8"...8" Tel: P/ 5524 Rev.

9 M-M M32 xpert eries lass Fiber Optic xcess ain eam Pattern xcess ain eam Pattern. m.33' T3 Fibers. m.33' T23 Fibers m 3.3' M32F Opposed Mode lass Fibers T23 Fibers w/l9 lenses m 33' 5 mm 5 mm M32F Opposed Mode T3 mm 2 mm 8" 3 mm 4 mm 6" T23 3" " " 3" 5 mm mm.4 " T3 Fiber mm. T23 Fiber M32F lass Fibers mm mm.9 mm.3 mm.65 mm.65 mm.3 mm.9 mm M32F T3 7.5 mm 5 mm 22.5 mm.3 ".6 ".9 ".75 ".5 ".25 " T23.25 ".5 ".75 " 3 mm 37.5 mm.2 ".5 " mm. T3 Fiber mm. M32FV Opposed Mode mm 4." T23 Fiber mm 5 mm 5 mm M32FV Opposed Mode 5 mm T3 mm 5 mm 6" T23 2 mm 8" 3" " " 3" ". mm.4 " T3 Fiber mm.4 " M32FV T23 Fiber mm.4 " mm M32FV.95 mm.3 mm.65 mm T3.65 mm.3mm.95 mm 5 mm mm 5 mm.2 ".4 ".6 " T23 2 mm.8 ".75 ".5 ".25 ".25 ".5 ".75 ". ". mm.4 " T3 Fiber mm.4 " M32FV M32FV M32FVW T23 Fiber mm.4 " mm 4. " M32FV 3. mm M32FV. 2. mm M32FVW.8". mm. mm T3 8 mm.3" T23 6 mm.6" 24 mm.9" 32 mm. 4 mm.5".. 2. mm.8" 3. mm. Plastic Fiber Optic xcess ain eam Pattern xcess ain eam Pattern mm.4 " PT26U Fiber mm.4 " M32FP Opposed Mode Plastic Fibers PT46U Fiber mm 4. " mm 45 mm 3 mm 5 mm 5 mm 3 mm 45 mm M32FP Opposed Mode PT26U " 5 mm 3" PT46U mm 5".8"..6".6"..8". mm.4 " PT26U Fiber mm.4 " M32FP Plastic Fibers mm. PT46U Fiber mm 3.8 mm 2.5 mm.2 mm.2 mm 2.5 mm 3.8 mm M32FP PT26U 7.5 mm.3 " 5 mm.6 " PT46U 22.5 mm.9 " 3 mm.2 " 37.5 mm.5 ".5 ". ".5 ".5 ". ".5 " P/ 5524 Rev. - Tel:

10 M-M M32 xpert eries xcess ain eam Pattern xcess ain eam Pattern. mm.4 in mm.4 in M32FP M32FP M32FPW Plastic Fiber mm.4 in PT46U Fiber mm 4 in 3. mm 2. mm. mm. mm 2. mm 3. mm 4 mm.5" Plastic Fiber 8 mm.3" PT46U 2 mm.45" M32FP M32FP M32FPW 6 mm.6" 2 mm.75"..8"...8". Troubleshooting f the M-M xpert s Power LD alternately flashes red/green, this indicates a microprocessor memory error. To clear the error, re-teach the sensor or cycle the power O and OFF and re-teach the sensor. f this does not solve the problem, or if it occurs frequently, replace the sensor. ccessories Retroreflective Targets anner offers a wide selection of high-quality retroreflective targets. ee your current anner ngineering orp catalog for complete information on available models. ensing range will vary, according to the retroreflector s efficiency and reflective area. For long-range applications: model RT-7777 reflector provides a range up to 2 m (6.5'). For clear object detection (low-contrast applications): reflector model RT-22 is recommended; one comes bundled with each M32LP(QD) sensor. Polarized sensors require corner-cube type retroreflective targets only; reflective tape is not recommended. efore installing retroreflective tape, clean the mounting surface with an isopropyl alcohol wipe. Optional brackets for mounting reflective targets are available. ee the ccessories section of your current anner catalog or our website at RT-22 quare, acrylic target Reflectivity factor:. Max. temperature: +5 (+22 ºF) Optional brackets are available pproximate size: 5 mm 5 mm RT-7777 quare, acrylic target Reflectivity Factor: 2. Temperature: 2 to +6 ( 4 F to +4 F) Optional brackets are available pproximate size: 84.5 mm 84.5 mm 84.5 mm (3.3") 77 mm (3.") 3.5 mm (.3") 84.5 mm (3.3") 77 mm (3.") 9 mm (.) lear crylic Lens RT-TVH Reflectivity factor:.8 Max. Temperature: +6 (+4 F) Retroreflective tape is available in a variety of sizes and shapes; see your anner atalog for more information. ot recommended for use with clear object detection sensors. - Tel: P/ 5524 Rev.

11 M-M M32 xpert eries 5-Pin uro-tyle ordsets 5-Pin Threaded M2/uro-tyle ordsets ingle nded Model Length tyle Dimensions Pinout (Female) MQD-5.5 MQD-56.5 m (.5 ft).83 m (6 ft) 44 Typ. MQD-55 MQD m (5 ft) 9.4 m (3 ft) traight M2 x ø MQD-56R MQD-55R MQD-53R.83 m (6 ft) 4.57 m (5 ft) 9.4 m (3 ft) Right-ngle M2 x ø 4.5 [.57"] 32 Typ. [.26"] 3 Typ. [.8"] 4 = rown 2 = White 3 = lue 4 = lack 5 = ray 3 5 Mounting rackets M46L Right-angle L bracket 4-ga. 36 stainless steel M46 Right-angle bracket 4-ga. 36 stainless steel Hole center spacing: = 6. Hole size: = Hole center spacing: = 6. Hole size: = , = 34.. M46U Right-angle U bracket for sensor protection 4-ga. 36 stainless steel M8 Right-angle mounting bracket with a curved slot for versatile orientation 2-ga. stainless steel 8 mm sensor mounting hole learance for M4 (#8) hardware Hole center spacing: = 6. Hole size: = , = Hole center spacing: to = 24.2 Hole size: = ø 4.6, = , = ø 8.5 P/ 5524 Rev. - Tel:

12 M-M M32 xpert eries M8F.. Protective, swivel bracket with tilt and pan movement for precision adjustment asy sensor mounting to extruded rail T-slots Metric and inch size bolts available Mounting hole for 8 mm sensors Hole size: = ø 8. ø8. 3/8-6 U 2 in ø9.8 5 M8Q Right-angle flanged bracket 8 mm sensor mounting hole 2-ga. stainless steel Hole center spacing: to = 24.2 Hole size: = ø 4.6, = , = ø Model olt Thread () M8F 3/8-6 2 in M8FM M M8F 8 mm swivel bracket with M8 internal thread lack thermoplastic polyester tainless steel swivel locking hardware included Hole center spacing: = 36. Hole size: = ø 5.3, = ø M8UR 2-piece universal swivel bracket 3 series stainless steel tainless steel swivel locking hardware included Mounting hole for 8 mm sensor Hole center spacing: = 25.4, = 46.7 Hole size: = , = ø M32PD Right-angle mounting bracket with a curved slot for versatile orientation 2-ga. stainless steel 8 mm sensor mounting hole learance for M4 (#8) hardware MM8R Right-angle MM series bracket with 8 mm hole rticulation slots for 9+ rotation 2-ga. (2.6 mm) coldrolled steel Hole center spacing: to = 24.2 Hole size: = ø 4.6, = 7 4.6, = ø 8.5 Hole center spacing: = 26., to = 3. Hole size: = , = ø 6.5, = ø 9. OT: ot for use with plastic fiber optic sensors MM8P Flat MM series bracket with 8 mm hole rticulation slots for 9+ rotation 2-ga. (2.6 mm) coldrolled steel Hole center spacing: = 26., to = 3. Hole size: = , = ø 6.5, = ø M3K Flat-mount swivel bracket with extended range of motion lack reinforced thermoplastic polyester and 36 stainless steel tainless steel swivel locking hardware included Hole center spacing: = 5.8 Hole size: = ø 7, = ø Tel: P/ 5524 Rev.

13 M-M M32 xpert eries M38 8 mm swivel side or barrel-mount bracket lack reinforced thermoplastic polyester tainless steel swivel locking hardware included M3U ide-mount swivel with extended range of motion lack reinforced thermoplastic polyester tainless steel swivel locking hardware included Hole center spacing: = 5.8 Hole size: = ø 7., = ø 8. Hole center spacing: = 5.8, = 24. Hole size: = ø 7, = ø 7.6 M32 tainless steel 2-axis, side-mount bracket M32 tainless steel 2-axis, bottom-mount bracket ncludes mounting foot = diam. 6.9, = 4.3.5, = = , = diam. 3, = anner ngineering orp. Limited Warranty anner ngineering orp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. anner ngineering orp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the anner product. TH LMTD WRRTY LUV D LU OF LL OTHR WRRT WHTHR PR OR MPLD (LUD, WTHOUT LMTTO, Y WRRTY OF MRHTLTY OR FT FOR PRTULR PURPO), D WHTHR R UDR OUR OF PRFORM, OUR OF DL OR TRD U. This Warranty is exclusive and limited to repair or, at the discretion of anner ngineering orp., replacement. O VT HLL R R ORP. LL TO UYR OR Y OTHR PRO OR TTY FOR Y TR OT, P, LO, LO OF PROFT, OR Y DTL, OQUTL OR PL DM RULT FROM Y PRODUT DFT OR FROM TH U OR LTY TO U TH PRODUT, WHTHR R OTRT OR WRRTY, TTUT, TORT, TRT LLTY, L, OR OTHRW. anner ngineering orp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by anner ngineering orp. opyright otice ny misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. ny modifications to this product without prior express approval by anner ngineering orp will void the product warranties. ll specifications published in this document are subject to change; anner reserves the right to modify product specifications or update documentation at any time. For the most recent version of any documentation, refer to: anner ngineering orp. ll rights reserved. - Tel: