Cisco Content Service Switches Management Module

Transcription

1 SPECTRUM Enterprise Manager Device Management Titlepage Cisco Content Service Switches Management Module Supports Management Module SM-CIS19

2 Notice Aprisma Management Technologies, Inc. (Aprisma), reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Aprisma to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Copyright October 2 by Aprisma Management Technologies. All rights reserved. Printed in the United States of America. Order Number: Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH 3824 SPECTRUM, thespectrum IMT/VNM logo, DCM, IMT, andvnm are registered trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, andvirtual Network Machine are trademarks of Aprisma or its affiliates. Ethernet is a trademark of Xerox Corporation. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the Licensed Software is virus-free. Aprisma has tested its software with current virus checking technologies. However, because no anti-virus system is 1% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence. Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise expressly stated in the contract. (b) This computer software may be: (1) Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred; (2) Used or copied for use in a backup computer if any computer for which it was acquired is inoperative; (3) Reproduced for archival or backup purposes; (4) Modified, adapted, or combined with other computer software, provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights; (5) Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and (6) Used or copied for use in or transferred to a replacement computer. (c) Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosure prohibitions, with the minimum rights set forth in paragraph (b) of this clause. (d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract. (e) This Notice shall be marked on any reproduction of this computer software, in wholeorinpart. SPECTRUM Enterprise Manager Page2 Cisco Content Service Switches

3 Contents Contents Contents INTRODUCTION 5 Purpose and Scope...5 Required Reading...5 Supported Devices...6 The SPECTRUM Model...6 TASKS 8 Application Information (examine)...8 Device (configure)...8 Device Performance (monitor)...8 Enabling/Disabling a Port (examine)...8 Interface Mask and Address (examine)...8 Model Information (examine)...8 Model Redundancy (configure)...8 Port Configuration (examine/modify)...8 Port Statistics (monitor)...8 DEVICE VIEWS 9 Interface Device View...9 Interface Icon...1 Interface Number Label...1 Administrative Status Label...1 Interface Type Label...11 Interface Description Label...11 Physical Address Label...11 IP Address Label...11 Gauge Label Gauge Control Panel Interface Icon Subviews Menu Interface Status View Secondary Address Panel Interface Address Translation Table Interface Threshold View DEVICE TOPOLOGY VIEWS 14 Interface Device Topology View APPLICATION VIEWS 15 Application Icons Supported Applications PERFORMANCE VIEWS 17 Device Performance View Gen Bridge App MIB-ll Performance View CONFIGURATION VIEWS 19 Device Configuration View Interface Configuration View... 2 MODEL INFORMATION VIEWS 21 SPECTRUM Enterprise Manager Page3

4 Contents Contents INDEX 22 SPECTRUM Enterprise Manager Page4

5 Introduction This section introduces the SPECTRUM Device Management documentation for Cisco Content Service switches. This introduction to the Device Management documentation for Cisco Content Service switches contains the following information: Purpose and Scope Required Reading Supported Devices (Page 6) The SPECTRUM Model (Page 6) Purpose and Scope Use this documentation as a guide for managing Cisco Content Service switches with the SPECTRUM management module SM-CIS19. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Cisco Content Service switches through software models in your SPECTRUM database. Only information specific to the supported management module is included under this documentation topic. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How To Manage Your Network with SPECTRUM SPECTRUM Views Software Release Notes SPECTRUM Menus SPECTRUM Icons Management Module SRN SPECTRUM Enterprise Manager Page5 Cisco Content Service Switches

6 Introduction Supported Devices The Cisco Content Service switches support TCPand UDP-based Web protocols wire-speed NAT, and intergrated IP Routing. They are built to solve problems that affect web-based business, such as increased traffic and flash crowds that swamp web sites, lost shopping carts, denial of service attacks, and slow downloads. Cisco Content Service CS 5 This switch has eight full-duplex Fast Ethernet ports and one optional Gigabit Ethernet port. The SPECTRUM Model Supported Devices SPECTRUM uses a single device model type, CiscoCSS115, for modeling any of the supported Cisco Content Service Switch devices. CiscoCSS115 models are represented in SpectroGRAPH views by Device icons. As Figure 1 shows, the appearance of the Device icon varies slightly depending on the kind of view it appears in. Figure 1: Device Icon Subviews Menu Options Cisco Content Service CS 15 This switch has 12 or 16 full duplex Fast Ethernet ports or 12 Fast Ethernet plus two Gigabit Ethernet ports. Cisco Content Service Switches CS 8 This switch has up to 64 full duplex 1BASE-TX ports, up to 48 1BASE-TX ports with 16 1BASE-FX ports, up to 32 Gigabit Ethernet interfaces, or a combination of interfaces. JK2 CiscoCSS115 Zoom -> Device Device Topology Application Acknowledge Flash Green Enabled Configuration Model Information SPECTRUM Enterprise Manager Page6 Cisco Content Service Switches

7 Introduction The SPECTRUM Model The views listed below are accessible directly from this menu and are described individually in subsequent sections of this documentation. Device Views (Page 9) Device Topology Views (Page 14) Application Views (Page 15) Performance Views (Page 17) Configuration Views (Page 19) Model Information Views (Page 21) SPECTRUM Enterprise Manager Page7 Cisco Content Service Switches

8 Tasks This section identifies various management and troubleshooting tasks that can be performed for the Cisco Content Service switches using the views, icons and labels referenced within this document. Application Information (examine) Application Views (Page 15) Device (configure) Device Views (Page 9) Device Performance (monitor) Device Views (Page 9) Performance Views (Page 17) Enabling/Disabling a Port (examine) Interface Status View (Page 12) Administrative Status (Page 12) Admin. Status (Page 2) Model Redundancy (configure) Device Views (Page 9) Port Configuration (examine/modify) Interface Device View (Page 9) Interface Icon (Page 1) Device Configuration View (Page 19) Port Statistics (monitor) Device Performance View (Page 17) Gen Bridge App (Page 18) MIB-ll Performance View (Page 18) Interface Mask and Address (examine) Secondary Address Panel (Page 12) Model Information (examine) Model Information Views (Page 21) SPECTRUM Enterprise Manager Page8 Cisco Content Service Switches

9 Device Views This section describes the Device views and subviews available for models of the Cisco Content Service switches in SPECTRUM. Device views use icons and labels to represent the modeled device and its components, such as modules and ports. There is one Device view for the Cisco Content Service switch: the Interface Device view. Interface Device View This view provides dynamic configuration and performance information for each of the device s serial/network I/O ports, which are represented by Interface icons in the bottom panel of the view, as shown in Figure 2. The middle panel of the view also displays a Device icon, which allows you to monitor device operation and access other device-specific views. Figure 2: Interface Device View SpectroGRAPH: Route Device: JK2 File View Tools Bookmarks Help? Model Name Contact Description Location ddhcp83 ddhcp83 Find 1 OFF 2 ON OFF 9 OFF -8 gigabitethernet -9 Network Address Interface Description Primary Application Phys Addr 3 OFF -3 1 ON PPTPS Serial-Mgmt. 4 OFF OFF -Mgmt 5 OFF -5 Sys Up Time Manufacturer Device Type Serial Number 6 OFF -6 7 OFF -7 SPECTRUM Enterprise Manager Page9 Cisco Content Service Switches

10 Device Views Interface Device View Interface Icon Figure 3 shows a close-up of an Interface icon from an Interface Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. a b c d e f g (a) Figure 3: (b) 1 OFF -1 (c) (d) (e) (f) (g) Interface Number Label Administrative Status Label Interface Type Label Interface Description Label Physical Address Label IP Address Label Gauge Label Interface Icon Interface Number Label This label identifies the interface. The number represents the interface number on this device. Administrative Status Label This label displays the current Operational Status of the interface (see Table 1). Note that the background color of the label also depends on the interface s current Administrative Status, which is set by the user in the Interface Status View (Page 12). This view can be accessed by doubleclicking this label. Color Table 1: Operational Status Administrative Status Administrative Status Green ON ON ON Blue OFF OFF OFF Yellow OFF ON OFF Label Text SPECTRUM Enterprise Manager Page1 Cisco Content Service Switches

11 Device Views Interface Device View Interface Type Label This label displays the type of interface module. Double-click this label to open the Interface Configuration View (Page 2). Interface Description Label This label identifies the type of network to which this interface is connected. Double-click this label to open the Serial Interface Model Information View for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the Interface Address Translation Table (Page 13), which cross-references network addresses (IP addresses) to physical (MAC) addresses for selected nodes between networks. Double-clicking on any column entry opens an address-specific Address Translation Table Information view. This view provides the same information as the corresponding row for the Interface Address Translation Table (Page 13), but allows you to modify field values. IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 12), which allows you to change the address and mask for this interface. Gauge Label Displays the statistic selected from the Gauge Control Panel described in SPECTRUM Views and provides double-click access to the Performance Views (Page 17). Gauge Control Panel Access: Highlight the Interface Options panel and select Icon Subviews > Gauge Control Panel from the View menu. This panel allows you to change the type of statistical information displayed on the Gauge label of the Interface icon. See SPECTRUM Views for detailed information on this panel. SPECTRUM Enterprise Manager Page11 Cisco Content Service Switches

12 Device Views Interface Device View Interface Icon Subviews Menu Table 2 lists the Icon Subviews menu options available for the Interface Icon. Detail Option IF Status Table 2: Interface Icon Menu Opens the... Interface Detail view which shows three pie charts for Packet Breakdown, Error Breakdown, and Discard Breakdown statistics. For more information, please refer to SPECTRUM Views. Interface Status View (Page 12) that displays the Operational and Administrative Statuses. IF Configuration Interface Configuration View (Page 2) that provides information about the selected interface. IF Address Translation Table Secondary Address Panel Interface Address Translation Table (Page 13) view, which shows the Physical and Network address for each interface. Secondary Address Panel (Page 12) which displays the current IP address for this interface. Thresholds Interface Threshold View (Page 13) where you can change the Load, Packet Rate, Error Rate, and % Discarded Threshold On/Off statuses. Interface Status View Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Status. This view provides the following information on the status of the interface: Operational Status Displays the current operational state of the interface is displayed. Valid values are: On, Off, or Testing. Administrative Status Allows you to select the desired operational state of the interface. Valid values are: On, Off, or Testing. Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation Table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. SPECTRUM Enterprise Manager Page12 Cisco Content Service Switches

13 Device Views Interface Device View Interface Address Translation Table Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Address Translation Table. This table provides the physical and network addresses associated with the interface index. Interface Index The value that coincides with the interface. Physical Address The MAC address of the interface. Interface Threshold View Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Thresholds. The Interface Threshold view allows a user to set statistical thresholds on a per interface basis with the File > Save All Changes feature. Load Packet Rate Error Rate % Discarded Network Address The IP Address of the interface. SPECTRUM Enterprise Manager Page13 Cisco Content Service Switches

14 Device Topology Views This section provides brief descriptions of the Device Topology views available for models of Cisco Content ServiceswitchesinSPECTRUM. Device Topology views show the connections between a modeled device and other network entities. There is one type of Device Topology view for the Cisco Content Service switch: the Interface DevTop view. Figure 4: Interface Device Topology View SpectroGRAPH: Device Topology: JK2 File View Tools Bookmarks Help ddhcp83 Interface Device Topology View Cisco Systems COM COM ddhcp83 Access: From the Icon Subviews menu for the Device icon, select DevTop > Interface. The lower panel of the Interface Device Topology view (Figure 4) uses interface icons to represent the device s serial/network I/O ports. These icons provide the same information and menu options as those in the Interface Device View (Page 9). If there is a device connected to a particular interface, a device icon appears on the vertical bar above the interface icon with an icon representing the network group that contains the device. For more information, refer to SPECTRUM Views. 1 OFF -1 1:1:1:1 2 OFF -2 3 OFF -3 4 OFF -4 SPECTRUM Enterprise Manager Page14 Cisco Content Service Switches

15 Application Views This section describes the Application views and the associated application-specific subviews available for models of Cisco Content Service switches in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows an Application view in its default view mode (icon) where each of the application models is represented by an Application icon (see Figure 6 on Page 16 for a close-up). The Application icons are arranged hierarchically under the Device icon, with major applications in the top row and their respective minor applications stacked directly below. If you prefer to see applications displayed by name only, in a single vertical list, select View > Mode > List. Figure 5: Cisco Content Service Application View SpectroGRAPH: Application: ddhcp83 File View Tools Bookmarks Help Model Name Contact Description Location Network Address Primary Application Bridge App Bridge_App nning Tree an_tree_a JK2_Static Static_App JK2 ddhcp83 JK2_MIB-II SNMP2_Agent MP2-Agent JK2_ICMP ICMPApp ICMP_App JK2_IP MIB-ll IP2_App IP2_App JK2_Syste System2_App ystem2_ap JK2_TCP TCP2_App System Up Time Manufacturer Device Type Serial Number Standard R RMONApp RMONApp EProbe1 RMONEthe E Probe 2 RMONEthe E Probe 3 RMONEthe E Probe 4 TCP2_App RMONEthe SPECTRUM Enterprise Manager Page15 Cisco Content Service Switches

16 Application Views Application Icons Application Icons When the Application view is in Icon mode, each of the application models is represented by an Application icon (Figure 6). Double-clicking the Model Name label (a) at the top of the icon opens the associated Model Information view see Model Information Views (Page 21). For some applications, the Model Type label (c) at the bottom of the icon is also a double-click zone, which opens an application-specific view. Any views accessible through these double-click zones are also accessible from the Application icon s Icon Subviews menu. Supported Applications Cisco Content Service switches support only the common applications, listed in Table 3 along with their corresponding documentation subtopics. Table 3: Application Bridging (Gen_Bridge_App) MIB-II (SNMP2_Agent) Standard RMON (RMONApp) Common Applications For more info, see... Bridging Applications MIB-II Applications Management Module Guide for Standard RMON Figure 6: Application Icon (a) (b) (c) a b c Model Name Label / Model Information View Condition Status Label Model Type Label / Application-Specific View SPECTRUM Enterprise Manager Page16 Cisco Content Service Switches

17 Performance Views This section provides brief descriptions of the Performance views available for models of Cisco Content Service switches in SPECTRUM. Performance views provide statistical information about the operation of the device and packet frame information for the device and its ports. The following performance views are described in this section: Device Performance View Gen Bridge App (Page 18) MIB-ll Performance View (Page 18) Figure 7: Device Performance View SpectroGRAPH : IP Address_EthernetApp Device Performance View Access: From the Icon Subviews menu for the Device icon, select Device Performance. This view (Figure 7) includes both a graph and a table that show current, average, and peak values for the performance statistics. The view also provides button access to the Enterprise Alarm Manager, Event Log, Interface Threshold View, Interface Configuration View, Transmit and Receive statistics, and pie charts. For more information on Performance views, refer to SPECTRUM Views. SPECTRUM Enterprise Manager Page17 Cisco Content Service Switches

18 Performance Views G en B r i dg e A p p Gen Bridge App Access: From the Icon Subviews menu for the Gen Bridge App Application Device icon, select Performance. This view provides the following performance statistics about the packets being passed through the device: Received Rate % Filtered % Forwarded Transmitted Rate MIB-ll Performance View Access: From the Icon Subviews menu for the MIB-ll Application Device icon, select Performance. This view provides the following performance statistics about the packets being passed through the device: Frame Rate % Received % Transmitted % Error % Discarded SPECTRUM Enterprise Manager Page18 Cisco Content Service Switches

19 Configuration Views This section describes the various Configuration views and subviews available for models of Cisco Content ServiceswitchesinSPECTRUM. Configuration views allow you to view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of SM-CIS19 devices: Device Configuration View Interface Configuration View Device Configuration View Access: From the Icon Subviews menu for the Cisco CSS115 Device icon, select Configuration. Figure 8 provides status and configuration information about the device as a whole as well as on a port-by-port basis. It also provides button access to an Interface Address Translation Table (Page 13) and a subview that lets you establish redundancy for the model. Fields and column headings within the Device Configuration view and its subviews are explained in detail in SPECTRUM Views. Figure 8: Device Configuration View SpectroGRAPH : IP Address Device Configuration View Redundancy and Model Reconfiguration Options Interface Address Translation Sort Find Update Interface Configuration Table Index Description Type Bandwidth Physical Address Operation Status SPECTRUM Enterprise Manager Page19 Cisco Content Service Switches

20 Configuration Views Interface Configuration View Interface Configuration View Access: From the Icon Subviews menu for a selected InterfaceiconintheInterfaceDeviceview,selectInterface Configuration. Figure 9 is an example of the Interface Configuration view. Column headings are provided below for the selected interface: ý " " ý+ 'þ"' "' Figure 9: þý "' #" " + (' #" " + +" ý Interface Configuration View SpectroGRAPH: JK2 Interface Configuration View ý" ý++ #)+"ý(,þ&'(ý "ý ý&)þý "ý ý ý ý++ ý" + )+' ý++ ' " ý"#' ý ý ý ý " Operation Status The current operational state of the interface. Valid values are: On, Off, or Testing. Admin. Status The desired operational state of the interface. Valid values are: On, Off, or Testing. Last Change The System UpTime value when the interface entered its current operational state. IP Address/Network Mask This window provides a list of the user-defined names and IP addresses for the interface. Physical Address The Ethernet (MAC) address of the interface. Bandwidth The estimated bandwidth of the interface, measured in bits per second. For interfaces that do not vary in bandwidth, or no accurate estimate can be made, a nominal bandwidth is provided. Packet Size The largest packet that can be transmitted or received by the port, displayed in octets. Queue Length The length of the outbound packet queue, in packets. Func Addr Enables the IEEE Spanning Tree Protocol at the TrBRF level to use the IBM bridge functional. SPECTRUM Enterprise Manager Page2 Cisco Content Service Switches

21 Model Information Views This section provides a brief description of the Model Information views available for models of Cisco Content ServiceswitchesinSPECTRUM. Model Information views provide descriptive and configuration information about SPECTRUM models of individual devices, interfaces, and applications. Figure 1 shows an example of the Model Information view accessed from the Icon Subviews menu for the Cisco Content Service switches model s Device icon. Model Information views are also available for each of the Interface icons in the Interface Device and Interface Device Topology views, and for each of the Application icons in the Application view. Although these views may vary slightly depending on the particular entity being modeled, their basic layout and content are similar for most SPECTRUM management modules. Therefore these views are described in more detail in SPECTRUM Views. Figure 1: Model Information View SpectroGRAPH: JK2 File View Tools Bookmarks Help? Name Contact Description Location Primary Address General Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Model Information View Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Communication Information DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status Last Successful Poll LOGGED User-Defined Type POLLED SPECTRUM Enterprise Manager Page21 Cisco Content Service Switches

22 Index Index Index Symbols % Discarded 13, 18 % Error 18 % Filtered 18 % Forwarded 18 % Received 18 % Transmitted 18 A Address Translation Table 12 Admin. Status 2 Administrative Status 12 Administrative Status Label 1 Application Common Bridging (GenBridgingApp) 16 MIB-II (SNMP2_Agent) 16 Icons 15 Application Icon 16 Application Icons 16 Application Views 15 B Bandwidth 2 BRF Configuration View 2 C CiscoCSS115 6 Condition Status Label 16 Configuration Views 19 Configuration views 19 D Device Configuration View 19 Device icon 6, 9, 15 Device Performance View 17 Device Views 9 Devices supported by this module 6 E Error Rate 13 F Frame Rate 18 G Gauge Control Panel 11 I Icon mode 15 Icon Subviews Menus for Device icon 6 Icons Device 6, 15 Interface 1, 14 Interface Configuration View 2 Interface Device Topology View 14 Interface Device View 9, 14 Interface Icon Administrative Status 12 Administrative Status Label 1 Operational Status 12 Interface icon 1 Interface Index 13 Interface Number Label 1 SPECTRUM Enterprise Manager Page22

23 Index Index IP Address Label 11 IP Address/Network Mask 2 L Labels Application Icon Condition Status 16 Model Name 16 Model Type 16 Interface Physical Address Label 11 Last Change 2 List mode 15 Load 13 M MIB-ll Performance View 18 Mode (Icon or List) 15 Model 21 Model Information View 21 Model Information views 21 Model Name Label 16 Model type 6 Model Type Label 16 N Network Address 13 Network I/O ports 14 O Operation Status 2 Operational Status 12 P Packet Rate 13 Packet Size 2 Performance Views 17 Physical Address 13, 2 Purpose and Scope 5 Q Queue Length 2 R Received Rate 18 Required Reading 5 Restricted Rights Notice 2 RMON App 16 S Secondary Address Panel 12 Serial ports 14 SPECTRUM Model 6 Supported Applications 16 Supported Devices 6 T Trademarks 2 Transmitted Rate 18 V VA{ LANE and Outbound Performance View 19 Views Configuration 19 Device Configuration 19 Device Performance 17 Interface Configuration 2 SPECTRUM Enterprise Manager Page23