SEHI Supports Management Module SM-CSI1020

Transcription

1 SEHI Titlepage Supports Management Module SM-CSI1020 Device Management

2 Copyright Notice Document Copyright September 2001 by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III(g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 SEHI

3 Contents INTRODUCTION 5 Purpose and Scope...5 Required Reading...5 Supported Devices...6 The SPECTRUM Model...6 TASKS 8 Application Information (examine)...8 Device (configure)...8 Device Performance (monitor)...8 Model Information (examine)...8 Model Redundancy (configure)...8 Port Configuration (examine/modify)...8 DEVICE VIEWS 9 Physical Device View...9 Chassis Device View...10 SEHI Module Icon...11 Stack Frame and Error Breakdown...13 Frame Breakdown Pie Chart...13 Error Breakdown Pie Chart...13 Stackable Repeater Frame Size View...13 Frame Breakdown Pie Chart...14 Source Address...14 Repeater Source Address View...14 DEVICE TOPOLOGY VIEW 15 APPLICATION VIEWS 16 Main Application View Supported Applications Common Applications Device-Specific Applications Stackable Repeater DownLoad Application PERFORMANCE VIEWS 19 Device Performance View Port Performance View CONFIGURATION VIEWS 21 Device Configuration View Chassis Table Information DownLoad Application SEHI Module Configuration View Module Management Trap Configuration SEHI Port Configuration View Port Management Trap Configuration SEHI Stackable Configuration View Repeater Management Device Management Page 3 SEHI

4 Contents Contents Trap Configuration...26 MODEL INFORMATION VIEWS 27 INDEX 28 Device Management Page 4 SEHI

5 Introduction This section introduces the SPECTRUM Device Management documentation for SEHI devices. This introduction to the Device Management documentation for SEHI devices contains the following information: Purpose and Scope Required Reading Supported Devices (Page 6) The SPECTRUM Model (Page 6) Purpose and Scope Use this documentation as a guide for managing SEHI devices with the SPECTRUM management module SM-CSI1020. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot SEHI devices through software models in your SPECTRUM database. Only information specific to the supported management module is included under this documentation topic. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How To Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons Management Module Software Release Notice Device Management Page 5 SEHI

6 Introduction Supported Devices The SPECTRUM management module SM- CSI1020 supports the following devices. SEHI-22/SEHI-24: Intelligent 13 (12 RJ45s, 1 EPIM SEHI-32, SEHI-34: Intelligent, 13 (1RJ71, 1 EPIM) and 26 (2 RJ71s, 2 EPIMs) SEHI-xxs: SEHI devices with LANVIEWSSecure functionality SEH-32, SEH-34: Non-intelligent, 13 (1 RJ71, EPIM) and 26 (2 RJ71s, 2 EPIMs) ports SEH-22, SEH-24: Non-intelligent, 13 (12 RJ45s, 1 EPIM) and 26 (24 RJ45s, 2 EPIMS) ports The SPECTRUM Model Supported Devices The model type for the SEHI device is the HubCSISEHI. Modeling results in the creation of Device icons that represent the SEHI and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 8. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Small and Large Device Icons Model Name HubCSISEHI Small Device icon appears in Topology, Device Topology, Application, and Container views. Large Device icon appears in Device Topology, Location, and Interface Device views. Model Name HubCSISEHI Device Management Page 6 SEHI

7 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Accesses the... Device Device Views (Page 9) Device Topology Device Topology View (Page 15) Application Application Views (Page 16) Configuration Configuration Views (Page 21) Model Information Primary Application Model Information Views (Page 27) Menu options that let you select either Gen Bridge App or MIB-II as the primary application. The SPECTRUM Model The rest of this document covering the Empire Agent management module is organized as follows. Tasks (Page 8) Device Views (Page 9) Device Topology View (Page 15) Application Views (Page 16) Performance Views (Page 19) Configuration Views (Page 21) Model Information Views (Page 27) Device Management Page 7 SEHI

8 Tasks This section lists device management tasks alphabetically and provides links to descriptions of the views and/or tables used to perform the task. Application Information (examine) Application Views (Page 16) Device (configure) Configuration Views (Page 21) Device Performance (monitor) Device Performance View (Page 19) Model Information (examine) Model Information Views (Page 27) Model Redundancy (configure) Device Configuration View (Page 21) Port Configuration (examine/modify) Chassis Device View (Page 10) Device Configuration View (Page 21) Configuration Views (Page 21) Device Management Page 8 SEHI

9 Device Views This section describes the Device views and subviews available for models of SEHI devices in SPECTRUM. Device views use icons and labels to represent the modeled device and its components, such as modules, ports, and applications. There are three types of Device views for SEHI models. Physical Device View on Page 9 Chassis Device View on Page 10 Physical Device View The Physical Device view provides a graphical representation of the SEHI and allows access to the Module Configuration, DevTop, and Device views for the SEHI module. Figure 2 shows the SEHI Physical Device view. Table 1 list the available subviews for the SEHI Physical Device icon. Figure 2: File View Tools Bookmarks Model Name Contact Description Location Physical Device View SpectroGRAPH: Router Device_IP Address HubSTACK SEHI Cabletron Systems Network Address Primary Application 98 System Up Time Manufacturer Device Type Serial Number Help Device Management Page 9 SEHI

10 Device Views Table 1: Menu Selection SEHI Model Information SEHI Physical Device View Icon Subviews Opens the... Model Information Views on Page 27. SEHI Configuration Configuration Views on Page 21. Application View Application Views on Page 16. Module Notes Module Configuration Module Notes view. Configuration Views on Page 21. Module Performance Performance Views on Page 19, which details the same information as the Device Performance view. Module Frame and Error Breakdown Module Frame Size Stack Frame and Error Breakdown on Page 13. Stackable Repeater Frame Size View on Page 13. Module DevTop Device Topology View on Page 15. Security Configuration Channel A Module Security window. Chassis Device View Chassis Device View Access: From the Icon Subviews menu for the SEHI Device icon, select Device > Chassis. Figure 3 shows a representation of this view. This view displays information for the SEHI chassis and the module it contains. The Chassis Device view provides both menu access and double-click zone access to the view that monitors the modules, interfaces, or ports. Figure 3: SEHI Chassis Device View Primary Landscape 0x VNM Host - File View Tools Bookmarks Model Contact Descrip- Location SEHI 1 IN SEHI 3 B Net Addr Prime-App 1 E 1 E 1 E 9 E 8 E 7 E Frm Frm Frm Frm Frm Frm Frm 6 E Frm 5 E Sys Up Manufac- Device Type Serial Num- Networ R Frm 4 E 3 E 2E 1E Frm Frm Frm R WR R A 16 MG 2 E Frm 2 E Frm 2 E Frm 2 E Frm 2 E Frm 1 E Frm 1 E Frm 1 E Frm 1 E Frm 1 E Frm 1 E Frm 1 E Frm 16 1 E Frm 1 E Frm 1 E Frm 9 E Frm 8 E Frm 7 E Frm Frm E Frm E Frm E 3 E Frm 2E Frm 1E Frm MG Help Device Management Page 10 SEHI

11 Device Views SEHI Module Icon This icon represents the physical module, its location in the chassis and its front and back panel interface or ports.table 2 and Table 3 also show the available Icon Subviews menu available from the Stack portion of the Module and Port icons. Figure 4 (Page 12) shows a representation of a Stack Module icon for the SEHI Device in SPECTRUM. Table 2: Menu Description Stack Performance Stack Configuration Stack Model Information Stack Frame & Error Breakdown Stack Frame Size Stack Module Icon Subviews Menu Selections Opens the... Performance Views on Page 19. This view is the same as the Device Performance view, but provides information pertaining to the stack. SEHI Stackable Configuration View on Page 25. Model Information Views on Page 27. Stack Frame and Error Breakdown on Page 13. Stackable Repeater Frame Size View on Page 13. Table 2: Menu Description Repeater Redundancy Repeater Source Address Security Configuration SEHI Module Icon Stack Module Icon Subviews Menu Selections (Continued) Opens the... Channel A Redundancy Window. Refer to the SPECTRUM Portable Management Application for the SEHI-22/24 and SEHI-32/34. Channel A Source Address Window. Refer to the SPECTRUM Portable Management Application for the SEHI-22/24 and SEHI-32/34. Channel A Source Address Window. Refer to Chapter 5, Source Addressing, in the SPECTRUM Portable Management Application for the SEHI-22/24 and SEHI-32/34. Device Management Page 11 SEHI

12 Device Views Table 3: Menu Selection Navigate Port Icon Subviews Description Navigator sub-menu, allowing you to Navigate In or Up. For more information on the Navigator submenu refer to SPECTRUM Views. Alarms Alarm View containing alarms (if any) for the model. Refer to SPECTRUM Views. Notes Utilities Port Notes Port Configuration SPECTRUM Notes facility for the device. Refer to SPECTRUM Views. Utilities sub-menu, which includes these choices: Attribute Browser, Applications, Enterprise ConfigManager, MIB Tools, PathView, WatchManager and Ping. SPECTRUM Port Notes facility. SEHI Port Configuration View on Page 24, Port Performance Port Performance View. This view is the same as the Performance Views on Page 19, but provides statistics pertaining to the port. For more information on Performance views, refer to SPECTRUM Views. Port Frame & Error Breakdown Frame & Error Breakdown View for the selected port. Refer to SPECTRUM Views. Table 3: Menu Selection Port Frame Size & Protocols Port Redundancy Port Source Address Port Security Configuration Enable/Disable Port Figure 4: NotesFacility/Module Number Performance View/Device Label ack ConfigurationView / View Stack Button SEHI Module Icon Port Icon Subviews (Continued) Security Status Label Description Frame Size View for the selected port. Refer to SPECTRUM Views. Channel A Redundancy Window. Repeater Management on Page 25. Source Address on Page 14. SPMA Channel A Port Security Window. Refer to SPECTRUM Portable Management for the SEHI-22/24 and SEHI-32/34. SEHI Module Configuration View on Page 23, which allows you to toggle the selected port between enabled and disabled states. SEHI Module Icon 1 SEHI24 STACK UNLOCKED Device Management Page 12 SEHI

13 Device Views Stack Frame and Error Breakdown This view provides two color-coded pie charts presenting a breakdown of frame and error statistics. Each statistic is presented as a total amount since the SEHI was initialized and as a percentage of overall traffic. The statistics provided by the Frame Breakdown Pie chart and Error Breakdown Pie chart are described below. Frame Breakdown Pie Chart Good Frames The total number of good frames detected on this device. Collisions The total number of collisions detected by this device. Errors The total number of errors detected by this device. Error Breakdown Pie Chart Giants The total amount of giant packets received by this device. A giant packet exceeds 1518 bytes, not including preamble. SEHI Module Icon Runts The total amount of runt packets received by this device. A runt packet is one byte less than the standard Ethernet frame of 64 bytes, not including preamble. Alignment The total number of misaligned packets detected on this device. CRC The total number of packets received by this device with bad Cyclical Redundancy Checks (CRCs). OOW Collisions The total amount of collisions out of the standard window (51.2µs) due to a network problem. Stackable Repeater Frame Size View This view provides a color-coded pie chart presenting a breakdown of frame size statistics. Each statistic is presented as a total amount since the SEHI was initialized and as a percentage of overall traffic. Device Management Page 13 SEHI

14 Device Views Frame Breakdown Pie Chart This chart provides the following information: Runts The total number of frames less than 64 bytes in size seen on this device Bytes The total number of frames between 64 and 127 bytes in size seen on this device Bytes The total number of frames between 128 and 255 bytes in size seen on this device Bytes The total number of frames between 256 and 511 bytes in size seen on this device Bytes The total number of frames between 512 and 1023 bytes in size seen on this device. Source Address SEHI Module Icon Source Address tables are used to determine which frames will be forwarded through the SEHI from one network segment to another. This section provides a description of the source address views used to establish a source address table for the SEHI. Repeater Source Address View You can access the Repeater Source Address view by highlighting the SEHI Logical Module STACK Button (refer to Figure ), or single-clicking on the Logical Module STACK Button with the right mouse button, and selecting Repeater Source Address from the Icon Subviews menu. The Repeater Source Address window will appear Bytes The total number of frames between 1024 and 1518 bytes in size seen on this device. Giants The total number of frames greater than 1518 bytes in size seen on this device. Device Management Page 14 SEHI

15 Device Topology View This section provides brief descriptions of the Device Topology view available for models of SEHI devices in SPECTRUM. The Device Topology view (Figure 5) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device Views (Page 9). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 5: Interface Device Topology View SpectroGRAPH: Device Topology: IP_Address File View Tools Bookmarks Help HubSTACK IP_Address SEHI-42 l 1 ENB FRAME0 ERRORS 0 Device Management Page 15 SEHI

16 Application Views This section describes the main Application view and the associated application-specific subviews available for models of SEHI devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 6: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 6 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View documentation. File View Model Name Contact Description Location SpectroGRAPH: Application : IP_Address Tools Bookmarks Network Address Primary Application Network 1 StackRPTR JK2_MIB-II SNMP2_Agent MP2-Agent JK2_ICMP ICMPApp ICMP_App JK2_System System2_App System2_App JK2_UDP2 UDP2_App UDP2_App System Up Time Manufacturer Device Type Serial Number IP_Address HubCSISEHI Download CSI Download NetWork 2 TokenRIng Help Device Management Page 16 SEHI

17 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Common Applications, below Device-Specific Applications (Page 18) Common Applications For the most part, these applications represent the non proprietary MIBs supported by your device. Listed below (beneath the title of the document that describes them) are some of the common applications currently supported by SPECTRUM. Note: The documents listed are available for viewing at: Bridging Applications - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - Open Shortest Path First MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Miscellaneous Applications - FDDI - Point to Point - DS 1 - RS WAN - Frame Relay - Token Ring - DLSW - APPN - Ethernet - Fast Ethernet - ATM Client - DHCP Supported Applications Device Management Page 17 SEHI

18 Application Views Device-Specific Applications SPECTRUM imports the following device-level proprietary MIBs into its database: The views and subviews available for the SEHI device-specific applications are described in the rest of this section, grouped by major applications as listed below: Stackable Repeater on Page 18 DownLoad Application on Page 18 These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Stackable Repeater Stackable Repeater This application provides Stackable Repeater performance, device, configuration, and model information view. The Stackable Repeater views are the same as the ones available from the Chassis Device View on Page 10. DownLoad Application This application provides download functionality for the SEHI. The model type for this application is CtDownLoadApp. Table 4 lists all the application-specific subviews available from the Icon subviews menu for the DownLoad Application. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. Table 4: Menu Selection DownLoad Application Model Information Download Application Subviews Menu Opens the... DownLoad Application view. This is an SPMA view and is described in the SPECTRUM Portable Management Application Tools Guide. DownLoad Application Model Information view described in SPECTRUM Views. Device Management Page 18 SEHI

19 Performance Views This section provides brief descriptions of the Performance view savailable for models of SEHI devices in SPECTRUM. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 7. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. For more information on Performance views, refer to the SPECTRUM Views documentation. Figure 7: 0:40:0 0:30:0 0:20:0 Log Device Performance View SpectroGRAPH: Stackable Rpter File View Tools Bookmarks Name Contact Description Location Network Address Primary Application Primary Address Load Frame Rate Errors Graph Properties Value Average Peak Value Scroll to Date-Time System Up Time Manufacturer Device Type Serial Number Bridging of type CSIBridge of Landscape IP_Address:Primary Errors Frames Help The following paragraphs list the performance attributes displayed for each Performance view supported by this management module. Device Management Page 19 SEHI

20 Performance Views Device Performance View Device Performance View Access: From the Icon Subviews menu for the Device icon, select Performance. Current and historical frame transmission information is provided via the following attributes. Frame Rate % Received % Transmitted % Error % Discarded Port Performance View Access: From the Icon Subviews menu for the Device Interface icon, select Performance. Current and historical packet transmission information is provided via the following attributes. Load Packet Rate % Error % Discarded Device Management Page 20 SEHI

21 Configuration Views This section describes the various Configuration views and subviews available for models of SEHI devices in SPECTRUM. Configuration views allow you to view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of SEHI devices: Device Configuration View on Page 21 SEHI Port Configuration View on Page 24 SEHI Stackable Configuration View on Page 25 Figure 8: File View Tools Bookmarks Model Contact Description Location Primary Address Contact Status Device Configuration View SpectroGRAPH: IP_Address Device Configuration View IP Address Primary Application Number of Interfaces System Up Time Interface Type Interface Index Serial Number Help Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. This view (Figure 8) provides status and configuration information about the device as a whole as well as on a port-by-port basis. The Device Configuration View provides information on the configuration and operating status of the SEHI and allows you to modify the values of some fields. Chassis Table Information Component Table Slot Table Trap Table Download Application Download Device Management Page 21 SEHI

22 Configuration Views Chassis Table Information This section of the Device Configuration View provides the following buttons pertaining to the components in the stack: Component Table Click on this button to access the Community Names tool. The Community Names tool lets you quickly view and change community names for any MIB component. It also allows you to enable or disable certain MIB components to free up system resources. For more information on this tool, refer to the Spectrum Portable Management Application (SPMA) Tools Guide. Slot Table This button opens the SEHI Slot Table, which provides information about the types and positions of devices in the stack. You can sort, find, and update the information contained in the table with the buttons at the top left of the table. To activate the Sort or Find buttons, click on a column heading. Clicking on the Sort button will sort the selected column. The Find button allows you to search the column for a specific entry. The Update button updates the information contained in the entire table. The SEHI Slot Table provides the following information: Device Configuration View Slot The number identifying this module s position in the stack. The SEHI is always in position 1. Comp The number identifying the type of component running in this slot. This number corresponds to an ID number in the Component Table. Name The textual description identifying this module. Type The OID string identifying this module s device type. Version The hardware revision number for this module. Trap Table The Trap Table window is where you enable and disable traps and specify the IP address of the management workstation that receives and processes the trap messages. (Refer to the SPMA Tools Guide for more information.) Device Management Page 22 SEHI

23 Configuration Views DownLoad Application This section of the Device Configuration View provides the following button pertaining to the DownLoad Application for the device: Download Click on this button to access the TFTP DownLoad tool. The TFTP Download tool lets you set up the download parameters and control the download. In addition, the TFTP Download tool can direct a device to use firmware located on a network server instead of booting from code located on the device. (Refer to the SPMA Tools Guide for more information.) SEHI Module Configuration View SEHI Module Configuration View Access: Highlight the Chassis Module icon, and from the Icon Subviews menu, select Module Configuration. The Module Configuration View provides information on the configuration of the selected module and allows you to modify some of the values. Module Management This section of the Module Configuration view provides the following information on the module port configuration: Port Count Displays the total number of ports on this module. Ports On Displays the number of ports on the module with a status of ON or NLK. Ports Operational Displays the number of ports on the module that are currently transmitting or receiving packets. Device Management Page 23 SEHI

24 Configuration Views Module Ports This button allows you to enable all ports on the module by selecting Enable. Trap Configuration This section of the Module Configuration view provides the following buttons controlling the configuration of the module traps: Link Traps This button enables or disables Link traps for all ports on this module. Changing the value for the stack or device level overrides this setting. Segmentation Traps This button enables or disables Segmentation traps for all ports on this module. Changing the value for the stack or device level overrides this setting. SEHI Port Configuration View SEHI Port Configuration View You can access this view from the SEHI Device Chassis View by clicking on the port to highlight it and then selecting Port Configuration from the Icon Subviews menu.the Port Configuration View provides information on the configuration of the selected port and allows you to modify some values. Port Management This section of the Port Configuration view provides the following information: Port ID Displays the number identifying this port on this module. Administrative Status This button enables or disables the selected port. Operational Status Displays whether the port is Operational or Not-Operational. Segmentation Status Displays whether the port is Segmented or Not- Segmented. Device Management Page 24 SEHI

25 Configuration Views Link Status Displays whether the port is Linked or Not- Linked. Set Topological State Allows yout to enable a back-up port. Trap Configuration This section of the Port Configuration view provides the following buttons controlling the configuration of the port traps: Link Traps This button enables or disables Link traps for this port. Changing the value for the module, stack, or device level overrides this setting. Segmentation Traps This button enables or disables segmentation traps for this port. Changing the value for the module, stack, or device level overrides this setting. SEHI Stackable Configuration View SEHI Stackable Configuration View Access: From the Icon Subviews menu for the Stack button in the Chassis Device view, select Stack Configuration. The Stackable Configuration View provides information on the configuration of the entire stack and allows you to modify some values. Repeater Management This section of the Stackable Configuration view provides the following information on the stack configuration: Port Count Displays the total number of ports in this stack. Ports On Displays the number of ports in the stack with a status of ON or NLK. Ports Operational Displays the number of ports in the stack that are currently transmitting or receiving packets. Device Management Page 25 SEHI

26 Configuration Views SEHI Stackable Configuration View Trap Configuration This section of the Stackable Configuration view provides the following buttons controlling the configuration of the stack traps: Link Traps This button enables or disables Link traps for the entire stack. Segmentation Traps This button enables or disables Segmentation traps for the entire stack. Device Management Page 26 SEHI

27 Model Information Views This section provides a brief overview of the Model Information view. This view displays administrative information about the device and its applications and lets you set thresholds and alarm severity for the device. Figure 9 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Figure 9: Model Information View SpectroGRAPH: Model Information File View Tools Bookmarks Help Model Name Contact Description Net Addr Sys Up Time Manufacturer Device Type Location Primary App Serial Number General Information Communication Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status IP_Address of Landscape X: Primary Device Management Page 27 SEHI

28 Index A Alarm View 12 Alarms 12 Alignment 13 Application Device-specific 18 C Comp 22 Configuration views 21 Cyclical Redundancy Checks 13 D Device Configuration View 21 Device Performance View 19 Devices supported by this module 6 Disable Port 12 E Enable F Port 12 Find Button 22 G Giants 13 H Hardware Revision 22 L Link Status 25 M Module Configuration 24 Management 23 Module Configuration View 23 N Name 22 Navigate 12 Navigator 12 Network I/O ports 15 Notes 12 O OID 22 OOW Collisions 13 Operational Status 24 P Physical Device View Icon Subviews 10 Device Management Page 28 SEHI

29 Index Index Port Configuration 12 View 24 Count 23, 25 Frame & Error Breakdown 12 Size & Protocols 12 ID 24 Management 24 Notes 12 Performance 12 View 12 Source Address Table 12 Port Redundancy 12 Port Security Configuration 12 Ports On 23, 25 Operational 23, 25 R Repeater Source Address Table View 14 Repeater Management 25 Required Reading 5 Ring Port Configuration View 23 Runts 13 S Segmentation Status 24 Serial ports 15 Set Topological State 25 Slot 22 Sort Button 22 Source Address Tables 14 Stackable Configuration View 25 T Topological State 25 Trap Configuration 24, 25, 26 Type 22 U Update Button 22 Utilities 12 V Version 22 Views Application 16 Configuration 21 Device Performance 19 Device Management Page 29 SEHI