SPECTRUM Enterprise Manager. Device Management. Titlepage. Lucent Definity. Supports Management Module SM-LUC1001

Transcription

1 SPECTRUM Enterprise Manager Device Management Titlepage Lucent Definity Supports Management Module SM-LUC1001

2 Notice Aprisma Management Technologies, Inc. (Aprisma), reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Aprisma to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Copyright November 2000 by Aprisma Management Technologies. All rights reserved. Printed in the United States of America. Order Number: Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH SPECTRUM, thespectrum IMT/VNM logo, DCM, IMT, andvnm are registered trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, andvirtual Network Machine are trademarks of Aprisma or its affiliates. Ethernet is a trademark of Xerox Corporation. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the Licensed Software is virus-free. Aprisma has tested its software with current virus checking technologies. However, because no anti-virus system is 100% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence. Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise expressly stated in the contract. (b) This computer software may be: (1) Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred; (2) Used or copied for use in a backup computer if any computer for which it was acquired is inoperative; (3) Reproduced for archival or backup purposes; (4) Modified, adapted, or combined with other computer software, provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights; (5) Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and (6) Used or copied for use in or transferred to a replacement computer. (c) Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosure prohibitions, with the minimum rights set forth in paragraph (b) of this clause. (d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract. (e) This Notice shall be marked on any reproduction of this computer software, in wholeorinpart. SPECTRUM Enterprise Manager Page2 Lucent Definity

3 Contents Contents Contents INTRODUCTION 5 Purpose and Scope...5 Required Reading...5 Supported Devices...6 The SPECTRUM Model...6 TASKS 8 Application Information (examine)...8 Device Performance (monitor)...8 Enabling/Disabling a Port (examine)...8 Model Information (examine)...8 Port Configuration (examine/modify)...8 Port Statistics (monitor)...8 CLIENT VIEW 9 Switch Icon...10 Module Information View...10 Client Details...11 DEVICE TOPOLOGY VIEW 12 Interface Device Topology View...12 Interface Icon Subviews Menu Options...14 Interface Status View...14 Secondary Address Panel...14 APPLICATION VIEWS 15 Application Icons Supported Applications G3Chassis Application View Proxy Configuration Client Table PERFORMANCE VIEWS 18 Device Performance View MIB-ll Performance View SNMP Agent Detail View Packet Breakdown Errors In Breakdown Errors Out Breakdown CONFIGURATION VIEWS 20 Device Configuration View Interface Configuration View MODEL INFORMATION VIEWS 22 MANUAL MODELING 23 Map on Topology Connection Status Location Icon SPECTRUM Enterprise Manager Page3 Lucent Definity

4 Contents Contents Switch Icon...24 INDEX 25 SPECTRUM Enterprise Manager Page4 Lucent Definity

5 Introduction This section introduces the SPECTRUM Device Management documentation for Lucent Definity Proxy Agent. This introduction to the Device Management documentation for Lucent Definity Proxy Agent contains the following information: Purpose and Scope Required Reading Supported Devices (Page 6) The SPECTRUM Model (Page 6) Purpose and Scope Use this documentation as a guide for managing Lucent Definity Proxy Agent with the SPECTRUM management module SM-LUC1001. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Lucent Definity Proxy Agent through software models in your SPECTRUM database. Only information specific to the supported management module is included under this documentation topic. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How To Manage Your Network with SPECTRUM SPECTRUM Views Software Release Notes SPECTRUM Menus SPECTRUM Icons Management Module SRN SPECTRUM Enterprise Manager Page5 Lucent Definity

6 Introduction Supported Devices The SPECTRUM management module SM- LUC1001 currently allows you to model one type of Lucent Definity. The Lucent Definity Proxy Agent is a protocol conversion resource. The Proxy Agent software resides on a stand-alone personal computer and operates on the UnixWare Operation System. The main function is to convert management data from managed nodes and transmit the data to the management programs that reside of the Network Management System. The Proxy Agent supports both static and dynamic connections to managed nodes. You can assign up to 150 dynamic connections on the managed nodes screen. The Proxy Agent can support up to 30 connections which can be any combination of static and dynamic connections. The SPECTRUM Model Supported Devices SPECTRUM uses a single device model type, LucentProxy, for modeling any of the supported Lucent Definity devices. LucentDefinity Proxy Agent models are represented in SpectroGRAPH views by Device icons. As Figure 1 shows, the appearance of the Device icon varies slightly depending on the kind of view it appears in. Figure 1: Model Name LucentProxy Small and Large Device Icons Large Device icon appears in Device Topology, Location, and InterfaceDeviceviews. SmallDeviceiconappearsin Topology, Device Topology, Application, and Container views. Model Name LucentProxy SPECTRUM Enterprise Manager Page6 Lucent Definity

7 Introduction The SPECTRUM Model The views listed below are accessible directly from this menu and are described individually in subsequent sections of this documentation. Client View (Page 9) Device Topology View (Page 12) Application Views (Page 15) Performance Views (Page 18) Configuration Views (Page 20) Model Information Views (Page 22) Manual Modeling (Page 23) Note: Installing the DNM application will allow you to view the Data Network Management features. You can get these options by right clicking on the Device icon. This information will be covered in Lucent documentation. SPECTRUM Enterprise Manager Page7 Lucent Definity

8 Tasks This section identifies various management and troubleshooting tasks that can be performed for the Lucent Definity Proxy Agent using the views, icons and labels referenced within this document. Application Information (examine) Application Views (Page 15) Device Performance (monitor) Performance Views (Page 18) Enabling/Disabling a Port (examine) Admin. Status (Page 21) Model Information (examine) Model Information Views (Page 22) Port Configuration (examine/modify) Interface Icon (Page 13) Device Configuration View (Page 20) Port Statistics (monitor) Device Performance View (Page 18) MIB-ll Performance View (Page 19) SPECTRUM Enterprise Manager Page8 Lucent Definity

9 Client View This section describes the Client view and subviews available for models of the Lucent Definity Proxy Agent in SPECTRUM. Access: From the Icon Subviews menu for the LucentProxy Device icon, select Client. This view (Figure 2) is a representation of the Private Branch Exchange (PBX) that the proxy has modeled. Each PBX can be classed into one of three categories: USA, with an enumerated state A custom category, where the name is supplied when the switch is added A generic category. Each icon in the lower panel (for a close-up, see Figure 3) represents a switch. Figure 2: Client View SpectroGRAPH: Route Device: JK2 File View Tools Bookmarks Help? Model Name Contact Description Location USA New Hampshire Sw0 idle dynamic 60 Sw2 idle dynamic 60 Network Address USA Rhode Island Sw1 down dynamic 60 Primary Application Berkshire Sw3 idle dynamic 60 System Up Time Manufacturer Device Type Serial Number Generic Sw4 idle dynamic 60 Note: The Client View is not updated immediately. To do so, go into the Model and Redundancy View (from Device Configuration View) and hit Reconfigure. SPECTRUM Enterprise Manager Page9 Lucent Definity

10 Client View The SPECTRUM Model Switch Icon Figure 3 shows an example of a switch icon from a Client view. (c) (d) a b c d e f Figure 3: Type Area (a) USA New Hampshire Sw0 idle dynamic 60 (e) Client Name Connection Status Connection Type Connection Timeout Switch Icon (b) (f) Type The class of switch. Valid values are: USA, Custom, and Generic. Area An enumerated value if Type is USA. Client Name The name of the client switch. Connection Status The status of the connection. Valid values are: idle, up, down, lost, and error. Connection Type The type of connection. Valid values are: dynamic, and static. Connection Timeout The number of idle minutes to wait before a dynamic connection is dropped. Module Information View Access: From the Icon Subviews menu for the Type/Area section of the Client View, select Information. Type The class of switch. Valid values are: USA, Custom, and Generic. Area An enumerated value if Type is USA. SPECTRUM Enterprise Manager Page10 Lucent Definity

11 Client View The SPECTRUM Model Clients The number of clients. Reconfigure Chassis Clicking this button will automatically reconfigure the chassis. Client Details Access: From the Icon Subviews menu for the Switch icon section of the Client View, select Client. Client Name The name of the client switch. Connection Type The type of connection. Valid values are: dynamic, and static. Connection Status The status of the connection. Valid values are: idle, up, down, lost, and error. Connection Timeout The number of idle minutes to wait before a dynamic connection is dropped. SPECTRUM Enterprise Manager Page11 Lucent Definity

12 Device Topology View This section provides brief descriptions of the Interface Device Topology view available for models of Lucent Definity Proxy Agent in SPECTRUM. Device Topology views show the connections between a modeled device and other network entities. There is one type of Device Topology view for the Lucent Definity, the Interface Device Topology view. Figure 4: Interface Device Topology View SpectroGRAPH: Device Topology: JK2 File View Tools Bookmarks Help Interface Device Topology View Access: From the Icon Subviews menu for the Device icon, select Interface. The lower panel of the Interface Device Topology view (Figure 4) uses interface icons to represent the device s switch ports. If there is a device connected to a particular interface, a device icon appears on the vertical bar above the interface icon with an icon representing the network group that contains the device. 1 ON SFTWARLPBK lo0 0:0:0:0 2 ON other eee0 0:0:0:0 JK2 LucentProxy SPECTRUM Enterprise Manager Page12 Lucent Definity

13 Device Topology View Interface Device Topology View Figure 5 shows a close-up of an Interface icon from an Interface Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 5: a b c d e (a) Interface Icon (b) 1 ON SFTWARLPBK lo0 0:0:0:0 Interface Number Label IF Status Label Network Connection Interface Type Label IP Address Label (c) (d) (e) Interface Number Label This label displays the interface number. IF Status Label This label displays the current Operational Status of the interface (see Table 1). Note that the background color of the label also depends on the interface s current Administrative Status, which is set by the user. (See Interface Status View on Page 14.) This view can be accessed by doubleclicking this label. Table 1: Color Interface Status Label Colors Operational Status Administrative Status Green ON ON ON Label Text Blue OFF OFF OFF Yellow OFF ON OFF Red Testing Test TST Network Connection The internal network connection to itself. Doubleclicking on this will open the Interface Configuration View (Page 21). Interface Type Label This label identifies the type of interface into the network. Double-clicking on this will open the Model Information Views (Page 22). SPECTRUM Enterprise Manager Page13 Lucent Definity

14 Device Topology View Interface Device Topology View IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 14), which allows you to change the address and mask for this interface. Interface Icon Subviews Menu Options Table 2 lists the Icon Subviews menu options available for the Interface icon. Table 2: Interface Icon Subviews Menu Option Opens the... IF Status Interface Status View (Page 14). IF Configuration Interface Configuration View (Page 21). Model Information Associated Model Information views for the selected interface (see Model Information Views on Page 22). Interface Status View Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Status. This view provides information on the operational status of the interface and allows you to enable or disable the port. Operational Status The current state of the interface. Valid values are: On, Off, or Testing. Administrative Status This button allows you to select the desired operational state of the interface. Valid values are: On, Off, or Testing. Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. SPECTRUM Enterprise Manager Page14 Lucent Definity

15 Application Views This section describes the Application views and the associated application-specific subviews available for models of Lucent Definity Proxy Agent in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 6: Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 6 shows an Application view in its default view mode (icon) where each of the application models is represented by an Application icon (see Figure 7 on Page 16 for a close-up). The Application icons are arranged hierarchically under the Device icon, with major applications in the top row and their respective minor applications stacked directly below. If you prefer to see applications displayed by name only, in a single vertical list, select View > Mode > List. SpectroGRAPH: Application: JK2 File View Tools Bookmarks Help Model Name Contact Description Location Network Address Primary Application JK2_MIB-II SNMP2_Agent MP2-Agent JK2_ICMP ICMPApp ICMP_App JK2_IP IP2_App IP2_App JK2_Syste System2_App ystem2_ap JK2_TCP TCP2_App TCP2_App JK2 LucentProxy celtix g3chassis g3chassis MIB-ll System Up Time Manufacturer Device Type Serial Number SPECTRUM Enterprise Manager Page15 Lucent Definity

16 Application Views Application Icons Application Icons When the Application view is in Icon mode, each of the application models is represented by an Application icon (Figure 7). Double-clicking the Model Name label (a) at the top of the icon opens the associated Model Information view see Model Information Views (Page 22). For some applications, the Model Type label (c) at the bottom of the icon is also a double-click zone, which opens an application-specific view. Any views accessible through these double-click zones are also accessible from the Application icon s Icon Subviews menu. Figure 7: Application Icon (a) Supported Applications Lucent Definity Proxy Agent supports both common and device-specific applications. Applications that are common to many of the different types of devices managed by SPECTRUM are listed in Table 3 along with their corresponding documentation subtopics. Table 3: Application MIB-II (SNMP2_Agent) Common Applications For more info, see... MIB-II Applications A single device specific application exists for Lucent Definity Switch, g3chassis. (b) (c) a b c Model Name Label / Model Information View Condition Status Label Model Type Label / Application-Specific View SPECTRUM Enterprise Manager Page16 Lucent Definity

17 Application Views Supported Applications G3Chassis Application View This major application (model type g3chassis) provides one application-specific subview, as follows. Proxy Configuration Access: From the Icon Subviews for the g3chassis icon, select Configuration. Client Table This view contains the following information. External Name The External Name for a G3 client. Type The connection type for this G3 client. Valid values are: dynamic and static. Status The connection status for this G3 client. Valid values are: idle, up, down, lost, and error. Timeout The number of idle minutes to wait before a dynamic connection is dropped. Submap The default Submap Name used in administering managed node locations. Table 4 displays the valid submaps and descriptions. Submap Generic(0) USA(1) Custom(2) Table 4: Submap Description The switch is in the generic category. The g3clientstate is enumerated to which state the switch is in. The g3clientsubmapname is a text string with the name of the custom category in it. State A numeric value representing the state in which to place the managed node icon on the NMS if Submap is set to USA (Alabama = 0, Alaska = 1,... Wyoming = 49). Custom A custom category where the name is supplied when the switch is added. SPECTRUM Enterprise Manager Page17 Lucent Definity

18 Performance Views This section provides brief descriptions of the Performance views available for models of Lucent Definity Proxy Agent in SPECTRUM. Performance views provide statistical information about the performance of the device and its ports. The following Performance views are described in this section: Device Performance View MIB-ll Performance View (Page 19) Device Performance View Access: From the Icon Subviews menu for the Device icon, select Device Performance. This view (Figure 8) includes both a graph and a table that show current, average, and peak values for the performance statistics. The view also provides button access to the Enterprise Alarm Manager, Event Log, Interface Threshold View, Interface Configuration View (Page 21), Transmit and Receive statistics, and pie charts. Refer to SPECTRUM Views for more information. Figure 8: Device Performance View SpectroGRAPH : IP Address_EthernetApp SPECTRUM Enterprise Manager Page18 Lucent Definity

19 Performance Views MIB-ll Performance View MIB-ll Performance View Access: From the Icon Subviews menu for the MIB-ll Application Device icon, select Performance. This view provides the following performance statistics about the packets being passed through the device: Frame Rate % Received % Transmitted % Error % Discarded Bad Values Gen Errs Errors Out Breakdown Too Big No Such Name Bad Values Gen Errs SNMP Agent Detail View Access: From the MIB-ll Performance View, select the Detail button. Packet Breakdown Received Forwarded Errors Discards Errors In Breakdown ASN Parse Errs Too Big No Such Name SPECTRUM Enterprise Manager Page19 Lucent Definity

20 Configuration Views This section describes the various Configuration views and subviews available for models of Lucent Definity Proxy Agent in SPECTRUM. Configuration views allow you to view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of SM-LUC1001 devices: Device Configuration View Interface Configuration View Device Configuration View Access: From the Icon Subviews menu for the LucentDefinity Device icon, select Configuration. Figure 9 provides status and configuration information about the device as a whole as well as on a port-by-port basis. It also provides button access to an Interface Address Translation table and a subview that lets you establish redundancy for the model. Fields and column headings within the Device Configuration view and its subviews are explained in detail in SPECTRUM Views. Figure 9: Device Configuration View SpectroGRAPH : IP Address Device Configuration View Redundancy and Model Reconfiguration Options Interface Address Translation Sort Find Update Interface Configuration Table Index Description Type Operation Status Admin Status Packet Size SPECTRUM Enterprise Manager Page20 Lucent Definity

21 Configuration Views Interface Configuration View Interface Configuration View Access: From the Icon Subviews menu for a selected InterfaceiconintheInterfaceDeviceview,selectInterface Configuration. Column headings are provided below for the selected interface: Operation Status The current operational state of the interface. Valid values are: Up, Down, or Testing. Admin. Status The desired operational state of the interface. Valid values are: Up, Down, or Testing. IP Address/Network Mask This window provides a list of the user-defined names and IP addresses for the interface. Packet Size The largest packet that can be transmitted or received by the port, displayed in octets. SPECTRUM Enterprise Manager Page21 Lucent Definity

22 Model Information Views This section provides a brief description of the Model Information views available for models of Lucent Definity Proxy Agent in SPECTRUM. Model Information views provide descriptive and configuration information about SPECTRUM models of individual devices, interfaces, and applications. Figure 10 shows an example of the Model Information view accessed from the Icon Subviews menu for the SM-LUC1001 model s Device icon. Model Information views are also available for each of the Interface icons in the Interface Device and Interface Device Topology views, and for each of the Application icons in the Application view. Although these views may vary slightly depending on the particular entity being modeled, their basic layout and content are similar for most SPECTRUM management modules. Therefore these views are described in more detail in SPECTRUM Views. Figure 10: Model Information View SpectroGRAPH: JK2 File View Tools Bookmarks Help? Name Contact Description Location Primary Address General Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Model Information View Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Communication Information DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status Last Successful Poll LOGGED User-Defined Type POLLED SPECTRUM Enterprise Manager Page22 Lucent Definity

23 Manual Modeling This section provides a brief description of how to manually model the Lucent Definity in SPECTRUM. There are two way to manually model the Lucent Definity in SPECTRUM: By Model Type. When you model by model type, the Creation View appears. From here, you can choose to turn off the Map on Topology option. The default is Yes, indicating that you want the location icons and switches displayed. By IP. When modeling by IP, the Map on Topology option is always Yes. USA Rhode Island Figure 11: Map on Topology JK2 LucentProxy Location Icons Lucent Proxy USA New Hampshire Map on Topology Figure 11 shows a representation of mapping the switches onto the topology view. If the Map on Topology option were No, only the Lucent Proxy icon would show up in the Topology view. R1 Switches b36 SPECTRUM Enterprise Manager Page23 Lucent Definity

24 Manual Modeling Map on Topology Connection Status The connection status displays the status between the Lucent proxy and the switch. Table 5 describes the possible connections status indicates Table 5: Connection Status Connection Status Description Switch Icon The Switch icon displays the switches in your topology. Right clicking on the Switch icon brings up the Icon Subviews menu. Selecting Configuration will then bring the Client Details (Page 11). You can also access this by doubleclicking the down arrow of the Switch icon. Dark Green Light Green Yellow Red Orange Idle state. Connection has been made. Trying to connect the trap. Connection has failed. Unidentifiable error. Location Icon The Location icon allows you to place your switches into different groups, based on location. Right clicking on the Location icon brings up the Icon Subviews menu. Selecting Information will bring up the Module Information View (Page 10). SPECTRUM Enterprise Manager Page24 Lucent Definity

25 Index Index Index Symbols % Discarded 19 % Error 19 % Received 19 % Transmitted 19 A Address Translation table 14 Admin. Status 21 Administrative Status 14 Application Common MIB-II (SNMP2_Agent) 16 Icons 15 Application Icon 16 Application Icons 16 Application Views 15 C Client Details 17 Colors Interface Status Label 13 Condition Status Label 16 Configuration Views 20 Configuration views 20 Connection Status 24 D Device Configuration View 20 Device icon 6, 15 Device Performance View 18 Devices supported by this module 6 Discards 19 E Enterprise Alarm Manager 18 Errors 19 Event Log 18 F Forwarded 19 Frame Rate 19 I Icon mode 15 Icon Subviews Menus for Interface icon 14 Icons Device 6, 15 Interface 12, 13 Interface Configuration View 21 Interface Device Topology View 12 Interface icon 13 Interface Icon Subviews Menu Options 14 Interface Number Label 10 Interface Status View 14 Administrative Status 14 Operational Status 14 IP Address/Network Mask 21 L Labels Application Icon Condition Status 16 Model Name 16 Model Type 16 Interface SPECTRUM Enterprise Manager Page25 Lucent Definity

26 Index Index IF Status Label 13 Interface Number Label 13 Interface Type Label 13 List mode 15 Location Icon 24 M Map on Topology 23 MIB-ll Performance View 19 Mode (Icon or List) 15 Model 22 Model Information View 22 Model Information views 22 Model type 6 Model Type Label 16 Module Information 18 O Operation Status 21 Operational Status 14 P Packet Size 21 Performance Views 18 Physical Address 21 Purpose and Scope 5 R Required Reading 5 Restricted Rights Notice 2 S Secondary Address Panel 14 SPECTRUM Model 6 State 17 Supported Applications 16 Supported Devices 6 Switch Icon 24 T Trademarks 2 Transmit and Receive statistics 18 V VA{ LANE and Outbound Performance View 20 Views Configuration 20 Device Configuration 20 Device Performance 18 Interface Configuration 21 Interface Status 14 SPECTRUM Enterprise Manager Page26 Lucent Definity