SEHI Supports Management Module SM-CSI1020

Transcription

1 SEHI Titlepage Supports Management Module SM-CSI1020 Device Management

2 Copyright Notice Document Copyright 2003 by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III(g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 SEHI

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 TASKS 7 DEVICE TOPOLOGY VIEW 8 Chassis Information SEHI Port Configuration View Port Management Trap Configuration MODEL INFORMATION VIEWS 18 INDEX 19 APPLICATION VIEWS 9 Main Application View...9 Supported Applications...10 Common Applications...10 Device-Specific Applications...11 Stackable Repeater...12 Stackable Configuration View...12 Repeater Management...12 Trap Configuration...12 PERFORMANCE VIEWS 13 Port Performance View...14 CONFIGURATION VIEWS 15 Device Configuration View...15 Device Management Page 3 SEHI

4 Introduction This section introduces the SPECTRUM Device Management documentation for the SEHI devices manufactured by Cabletron. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this document as a guide for managing the Cabletron devices described on Page 5 with SPECTRUM management module SM-CSI1020. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot SEHI devices through software models in your SPECTRUM database. Information specific to SM-CSI1020 is what is primarily included in this document. For general information about device management using SPECTRUM and explanations of SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice Device Management Page 4 SEHI

5 Introduction Supported Devices SPECTRUM management module SM-CSI1020 currently supports the following devices: SEHI-22/SEHI-24: Intelligent 13 (12 RJ45s, 1 EPIM SEHI-32, SEHI-34: Intelligent, 13 (1RJ71, 1 EPIM) and 26 (2 RJ71s, 2 EPIMs) SEHI-xxs: SEHI devices with LANVIEWSSecure functionality SEH-32, SEH-34: Non-intelligent, 13 (1 RJ71, EPIM) and 26 (2 RJ71s, 2 EPIMs) ports SEH-22, SEH-24: Non-intelligent, 13 (12 RJ45s, 1 EPIM) and 26 (24 RJ45s, 2 EPIMS) ports The SPECTRUM Model Supported Devices The model type for Cabletron SEHI devices is HubCSISEHI. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Device Icons Model Name Small Device icon appears in Topology and Application views HubCSISEHI Large Device icon appears in Device Topology, Location, and Device Interface views. Model Name HubCSISEHI Device Management Page 5 SEHI

6 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Fault Management Accesses the... Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation. DevTop Device Topology View (Page 8) Application Application Views (Page 9) Configuration Configuration Views (Page 15) Model Information Primary Application Model Information Views (Page 18) Menu options that let you select the primary application; for example, Gen Bridge App, MIB-II, etc. The SPECTRUM Model The rest of this document covering management module SM-CSI1020 is organized as follows: Tasks (Page 7) Device Topology View (Page 8) Application Views (Page 9) Configuration Views (Page 15) Model Information Views (Page 18). Device Management Page 6 SEHI

7 Tasks This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information Views (Page 18) Configuration Information (check) Configuration Views (Page 15) Topology (check) Device Topology View (Page 8) Device Management Page 7 SEHI

8 Device Topology View This section describes the Device Topology view available for models of the SEHI devices. Access: From the Icon Subviews menu for the Device icon, select DevTop. The Device Topology view (Figure 2) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 2: Device Topology View SpectroGRAPH: Device Topology: IP_Address File View Tools Bookmarks Help HubSTACK IP_Address SEHI-42 l 1 ENB FRAME0 ERRORS 0 Device Management Page 8 SEHI

9 Application Views This section describes the main Application view and the associated application-specific subviews available for models of SEHI devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 3: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 3 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the Application View and MIBs document. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Contact Description Location Network Address System Up Time Manufacturer Device Type Serial Number Model Name Model 6E132_25 Type Help Model Name of type <model type> of Landscape node: Primary Device Management Page 9 SEHI

10 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Applications associated with non-proprietary MIBs. See Common Applications below. Applications associated with device-specific MIBs. See Device-Specific Applications (Page 11). Common Applications For the most part, these applications represent the non proprietary MIBs supported by devices. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Refer to these documents when your devices support these applications. Note: The documents listed below (in bold font) are available for viewing at: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - OSPF - OSPF2 - BGP4 - VRRP - RFC 2932 Bridging Applications - Ethernet Special Database - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation - QBridge MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Transmission Applications - FDDI - Point to Point Supported Applications Device Management Page 10 SEHI

11 Application Views - DS1 - DS3 - RS WAN - Frame Relay - Token Ring - Ethernet - RFC 1317App - RFC 1285App - RFC 1315App App - SONET - DOCSISBPIApp - DOCSISIFApp Supported Applications Digital Subscriber Line (DSL) Applications - ADSL Device-Specific Applications The following device-specific application is described in the remainder of this section: Stackable Repeater (Page 12) Technology Applications - APPN - ATM Client - DHCP - DLSw - PNNI - RFC 1316App - RFC RFC RFC RFC 2925 DOCSIS Applications - DOCSISCblDvApp - DOCSISQOSApp - DOCSISBPI2App Device Management Page 11 SEHI

12 Application Views Stackable Repeater This application provides the Stackable Configuration View. Stackable Configuration View The Stackable Configuration view provides the following information on the module port configuration: Repeater Management Trap Configuration Repeater Management This section of the Stackable Configuration view provides the following information: Trap Configuration Stackable Repeater This section of the Stackable Configuration view provides the following buttons controlling the configuration of the module traps: Link Traps This button enables or disables Link traps for all ports on this module. Changing the value for the stack or device level overrides this setting. Segmentation Traps This button enables or disables Segmentation traps for all ports on this module. Changing the value for the stack or device level overrides this setting. Port Count Displays the total number of ports on this module. Ports On Displays the number of ports on the module with a status of ON or NLK. Ports Operational Displays the number of ports on the module that are currently transmitting or receiving packets. Device Management Page 12 SEHI

13 Performance Views This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 4. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 4: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Model Name Contact Description Location Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. 0:40:0 0:30:0 0:20:0 Value Average Peak Value Log * Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded 0 *Frames per second Graph Properties Scroll to Date-Time Detail type routing of type IP Routing of Landscape node: Primary Device Management Page 13 SEHI

14 Performance Views Port Performance View Port Performance View Access: From the Icon Subviews menu for the Device Interface icon, select Performance. Current and historical packet transmission information is provided via the following attributes. Load Packet Rate % Error % Discarded Device Management Page 14 SEHI

15 Configuration Views This section describes the various Configuration views and subviews available for models of SEHI devices in SPECTRUM. Configuration views allow you to view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of SEHI devices: Device Configuration View on Page 15 SEHI Port Configuration View on Page 17 Figure 5: File View Tools Bookmarks Model Contact Description Location Primary Address Device Configuration View SpectroGRAPH: IP_Address Device Configuration View IP Address Primary Application System Up Time Interface Type Interface Index Serial Number Help Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. This view (Figure 5) provides status and configuration information about the device as a whole as well as on a port-by-port basis. The Device Configuration View provides information on the configuration and operating status of the SEHI and allows you to modify the values of some fields. Contact Status Chassis Information Slot Table Number of Interfaces Device Management Page 15 SEHI

16 Configuration Views Firmware Revision Displays the firmware revision for the device being modeled. Hardware Revision Displays the hardware revision for the device being modeled. MAC Address Displays the Physical (Ethernet) address for the device being modeled. Chassis Information This section of the Device Configuration View provides the following buttons pertaining to the components in the stack: Slot Table This button opens the SEHI Slot Table, which provides information about the types and positions of devices in the stack. You can sort, find, and update the information contained in the table with the buttons at the top left of the table. To activate the Sort or Find buttons, click on a column heading. Clicking on the Sort button will sort the selected column. The Find button allows you to search the column for a specific entry. The Update button updates the information Device Configuration View contained in the entire table. The SEHI Slot Table provides the following information: Slot The number identifying this module s position in the stack. The SEHI is always in position 1. Comp The number identifying the type of component running in this slot. This number corresponds to an ID number in the Component Table. Name The textual description identifying this module. Type The OID string identifying this module s device type. Version The hardware revision number for this module. Device Management Page 16 SEHI

17 Configuration Views SEHI Port Configuration View You can access this view from the SEHI Device Topology View by selecting Port Configuration from the Icon Subviews menu for an interface icon. The Port Configuration View provides information on the configuration of the selected port and allows you to modify some values. Port Management This section of the Port Configuration view provides the following information: Port ID Displays the number identifying this port on this module. Administrative Status This button enables or disables the selected port. Operational Status Displays whether the port is Operational or Not-Operational. Segmentation Status Displays whether the port is Segmented or Not- Segmented. SEHI Port Configuration View Link Status Displays whether the port is Linked or Not- Linked. Set Topological State Allows you to enable a back-up port. Trap Configuration This section of the Port Configuration view provides the following buttons controlling the configuration of the port traps: Link Traps This button enables or disables Link traps for this port. Changing the value for the module, stack, or device level overrides this setting. Segmentation Traps This button enables or disables segmentation traps for this port. Changing the value for the module, stack, or device level overrides this setting. Device Management Page 17 SEHI

18 Model Information Views This section provides a brief overview of the Model Information view. This view displays administrative information about the device and its applications and lets you set thresholds and alarm severity for the device. Figure 6 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Figure 6: Model Information View SpectroGRAPH: Model Information File View Tools Bookmarks Help Model Name Contact Description Net Addr Sys Up Time Manufacturer Device Type Location Primary App Serial Number General Information Communication Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status IP_Address of Landscape X: Primary Device Management Page 18 SEHI

19 Index A Applications 9 C Comp 16 Configuration views 15 D Device Configuration View 15 DevTop Views 8 Documentation 4 F Find Button 16 H Hardware 5 Revision 16 I Icons Device 5 L Link Status 17 M Management Tasks 7 Model Types of 5 Module Configuration 17 N Name 16 Network I/O ports 8 O OID 16 Operational Status 17 P Performance Statistics 13 Port Configuration View 17 Count 12 ID 17 Management 17 Ports On 12 Operational 12 S Segmentation Status 17 Serial ports 8 Set Topological State 17 Slot 16 Sort Device Management Page 19 SEHI

20 Index Index Button 16 T Topological State 17 Trap Configuration 12, 17 Troubleshooting 7 Type 16 U Update Button 16 V Version 16 Views Configuration 15 Device Management Page 20 SEHI