Cisco Aironet Family

Transcription

1 Cisco Aironet Family Titlepage Supports Management Module SM-CIS1016 Device Management

2 Copyright Notice Document Copyright 2003-present by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III(g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 Cisco Aironet Family

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 TASKS 7 CONFIGURATION VIEWS 19 Device Configuration View MODEL INFORMATION VIEW 21 INDEX 22 DEVICE VIEW 8 Interface Icons...9 Interface Icon Subviews Menu...10 Secondary Address Panel...11 DEVICE TOPOLOGY VIEW 12 APPLICATION VIEWS 13 Main Application View...13 Supported Applications...14 Common Applications...14 Device-Specific MIBs...15 Discovery Application...16 Discovery Cache Table View...16 Interface Discovery Status Table...17 PERFORMANCE VIEWS 18 Device Management Page 3 Cisco Aironet Family

4 Introduction This section introduces the SPECTRUM Device Management documentation for the Cisco Aironet Wireless Access Point. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this document as a guide for managing the Cisco Aironet devices described on Page 5 with SPECTRUM management module SM-CIS1016. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Cisco Aironet devices through software models in your SPECTRUM database. Information specific to SM-CIS1016 is what is primarily included in this document. For general information about device management using SPECTRUM and explanations of SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice Cisco Applications Device Management Page 4 Cisco Aironet Family

5 Introduction Supported Devices SPECTRUM management module SM-CIS1016 currently lets you model the following devices: Cisco Aironet 340 Series Access Point Cisco Aironet 350 Series Access Point Cisco Aironet 1200 Series Access Point /1230 (IOS-based firmware) Cisco Aironet 1100 Series Access Point (IOSbased firmware) Cisco Aironet 1400 Series Access Point (IOSbased firmware) Note: The 1220, 1210/1230, 1100 and 1400 are only supported in SPECTRUM versions 6.6 SP5 and above. Cisco Aironet products can be integrated into wired Ethernet networks, and they provide protection through full compliance with the IEEE b wireless standard. Supported Devices The Cisco Aironet 1200 supports 2.4 GHz and 5 GHz radios simultaneously, preserving existing IEEE b investments and providing a migration path to future IEEE a and IEEE g technologies. The SPECTRUM Model The model types for the Cisco Aironet devices are Aironet and AironetIOS. The AironetIOS model type is used for those devices that have IOS-based firmware. Devices with non-ios-based firmware use the Aironet model type. Note: The AironetIOS model type is only supported in SPECTRUM versions 6.6 SP5 and above. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Device Management Page 5 Cisco Aironet Family

6 Introduction Model Name Cisco 1200 AP Figure 1: Large Device icon appears in Device Topology, Location, and Device Interface views. Device Icons Small Device icon appears in Topology and Application views Model Name Cisco 1200 AP Option The SPECTRUM Model DevTop Device Topology View (Page 12) Application Application Views (Page 13) Configuration Configuration Views (Page 19) Model Information Primary Application Accesses the... Model Information View (Page 21) Menu options that let you select the primary application; for example, Gen Bridge App, MIB-II, etc. The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Fault Management Accesses the... Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation. Device Device View (Page 8) The rest of this document covering management module SM-CIS1016 is organized as follows: Tasks (Page 7) Device View (Page 8) Device Topology View (Page 12) Application Views (Page 13) Performance Views (Page 18) Configuration Views (Page 19) Model Information View (Page 21). Device Management Page 6 Cisco Aironet Family

7 Tasks This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information View (Page 21) Topology (check) Device Topology View (Page 12) Alarm Thresholds (set) Interface Icon Subviews Menu (Page 10) Configuration Information (check) Configuration Views (Page 19) IP Address (find/change) Device View (Page 8) Secondary Address Panel (Page 11) Network Type (check) Network Type Label (Page 10) Performance (check) Device View (Page 8) Interface Icons (Page 9) Performance Views (Page 18) Device Management Page 7 Cisco Aironet Family

8 Device View This section describes the Device view and subviews available for models of Cisco Aironet devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Device. This view (Figure 2) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 2: Device View SpectroGRAPH: Router Device: Model Name File View Tools Bookmarks Help Model Name Contact Description Location Model Name Aironet 1 ON Ethernet ei0 0:0:1D:F:FD:B6 2 ON ATM CPU Network Address Primary Application Gen Bridge App Filter Physical Interface Description Device Icon 3 ON 4 ATM 7B2 Sys Up Time Manufacturer Device Type Serial Number Interface Options Panel ATM 8B3 ON 5 ON SFTWARLPBK lo0 0:0:1D:F:FD:B6 6 ON ATM port CPU.1 7 ON ATM 7B3 8 ON ATM 8B4 9 ON ATM8023 zn1 0:0:1D:F:FD:B6 512 ON AAL5 UAAL5 10 ON ATM 7A1 ON ATM 7B ON ATM 8B1 ON ATM 8B2 Interface Icons Model Name of type Model Type of Landscape node: Primary Device Management Page 8 Cisco Aironet Family

9 Device View Interface Icons Figure 3 shows a close-up of an Interface icon from the Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 3: a b c d e f a Interface Icon b 1 ON ethernet fxp0 0:0:1D:F:FD:B6 Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label c d e f Interface Icons Interface Number Label This label displays the interface (port) number. IF Status Label This label displays the current status of the interface for the primary application selected, e.g., Gen Rtr App or MIB-II App. Table 1 lists the possible label color representations. Note that the color of the label also depends on the interface s current Administrative Status, which you set in the Interface Configuration View. This view can be accessed by double-clicking the Interface Type label. Table 1: Color Interface Status Label Colors Operational Status Administrative Status Green up up ON Blue down down OFF Yellow down up OFF Label Text Red testing testing TEST Interface Type Label This label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Configuration view. See the SPECTRUM Views documentation. Device Management Page 9 Cisco Aironet Family

10 Device View Network Type Label This label identifies the type of network to which the interface is connected. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the Address Translation Table (AT). IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 11), which lets you change the address and mask for the interface. Interface Icon Subviews Menu Table 2 lists the device-specific interface Icon Subviews menu options and the views to which they provide access. Detail Table 2: Option IF Configuration Address Translation Table Secondary Address Panel Thresholds Model Information Trap Configuration Interface Icon Subviews Menu Interface Icon Subviews Menu Accesses the... Interface Detail view, which displays packet, error, and discard breakdown statistics for the interface. Interface Configuration view (see SPECTRUM Views). Address Translation Table (AT) (see SPECTRUM Views). Secondary Address Panel (Page 11). Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface. Model Information View (Page 21). Interface Trap Configuration view (see How to Manage Your Network with SPECTRUM). Device Management Page 10 Cisco Aironet Family

11 Device View Secondary Address Panel Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. Device Management Page 11 Cisco Aironet Family

12 Device Topology View This section describes the Device Topology view available for models of the Cisco Aironet devices. Access: From the Icon Subviews menu for the Device icon, select DevTop. The Device Topology view (Figure 4) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device View (Page 8). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 4: Device Topology View SpectroGRAPH: Device Topology: Model Name File View Tools Bookmarks Help Graphic of Cisco Aironet Device Model Name Aironet 1 ON 2 ON 3 ON Ethernet ei0 0:0:1D:F:FD:B6 ATM A2 0:0:1D:F:FD:B6 ATM CPU 0:0:1D:F:FD:B6 Model Name of type Model Type of Landscape node: Primary Device Management Page 12 Cisco Aironet Family

13 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Cisco Aironet devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 5: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View document. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Contact Description Location Network Address System Up Time Manufacturer Device Type Serial Number Model Name 6E132_25 Aironet Help Model Name of type <model type> of Landscape node: Primary Device Management Page 13 Cisco Aironet Family

14 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Applications associated with non proprietary MIBs. See Common Applications below. Applications associated with device-specific MIBs. See Device-Specific MIBs (Page 15). Common Applications For the most part, these applications represent the non proprietary MIBs supported by devices. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Refer to these documents when your devices support these applications. Note: The documents listed below (in bold font) are available for viewing at: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - OSPF - OSPF2 - BGP4 - VRRP - RFC 2932 Bridging Applications - Ethernet Special Database - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation - QBridge MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Transmission Applications - FDDI - Point to Point - DS1 - DS3 Supported Applications Device Management Page 14 Cisco Aironet Family

15 Application Views - RS WAN - Frame Relay - Token Ring - Ethernet - Fast Ethernet - RFC 1317App - RFC 1285App - RFC 1315App App - SONET Technology Applications - APPN - ATM Client - DHCP - DLSw - PNNI - RFC 1316App - RFC RFC RFC RFC 2925 DOCSIS Applications - DOCSISCblDvApp - DOCSISQOSApp - DOCSISBPI2App - DOCSISBPIApp - DOCSISIFApp Supported Applications Digital Subscriber Line (DSL) Applications - ADSL Device-Specific MIBs SPECTRUM imports the following device-level proprietary MIBs into its database: AWCVX-MIB.my ACW-VLAN-CFG-MIB.my These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. The following device-specific application is described in the remainder of this section: Discovery Application (Page 16) Device Management Page 15 Cisco Aironet Family

16 Application Views Discovery Application This application (CiscoCDPApp) has three menu options that provide access to the following views. Discovery Cache Table View (Page 16) Interface Discovery Status Table (Page 17) Model Information View (Page 21) Discovery Cache Table View Access: From the Icon Subviews menu for the CiscoCDPApp Application icon, select Cache. This table contains the cached information obtained by receiving Cisco Discovery Protocol (CDP) messages. Type An indication of the type of address contained in the corresponding instance of cdpcacheaddress. Discovery Application Device Port The Port-ID string as reported in the most recent CDP message. This will typically be the value of the ifname object (e.g., Ethernet0.) The zerolength string indicates no Port-ID field was reported in the most recent CDP message. Platform The device s hardware platform as reported in the most recent CDP message. The zero-length string indicates that no Platform field was reported in the most recent CDP message. Capabilities The device s functional capabilities as reported in the most recent CDP message. For the latest set of specific values, see the latest version of the CDP specification. The zero-length string indicates no Capabilities field was reported in the most recent CDP message. Address The (first) network-layer address of the device s SNMP-agent as reported in the most recent CDP message. Device ID The Device-ID string as reported in the most recent CDP message. The zero-length string indicates no Device-ID field was reported in the most recent CDP message. Device Management Page 16 Cisco Aironet Family

17 Application Views Discovery Application Interface Discovery Status Table Access: From the Icon Subviews menu for the CiscoCDPApp Application icon, select Interfaces. This table contains the status of Cisco Discovery Protocol (CDP) on the device s interfaces. IF The interface index value of the local interface. Discovery An indication of whether the Cisco Discovery Protocol is currently running on this interface. Group This object is only relevant to interfaces that are repeater ports on repeaters; it indicates the RFC1516 group number of the repeater port that corresponds to this interface. Port This object is only relevant to interfaces that are repeater ports on repeaters; it indicates the RFC1516 port number of the repeater port that corresponds to this interface. Interval The interval at which CDP (Cisco Discovery Protocol) messages are to be generated on this interface. The default value is 60 seconds. Device Management Page 17 Cisco Aironet Family

18 Performance Views This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 6. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 6: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Network Address Device Type Performance View Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. Day/Month/ Time/ Year :30 00:20 00:10 0 * Graph X 1000 Log Value Average Peak Value * Received/sec at % Discarded at % Forwarded at % Trans/sec at % Discarded Graph Properties Scroll to Date-Time Detail type routing of type IP Routing of Landscape node: Primary Device Management Page 18 Cisco Aironet Family

19 Configuration Views This section describes the Configuration views available for models of the Cisco Aironet devices in SPECTRUM. Configuration views let you see and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Cisco Aironet devices: Device Configuration View (Page 19) Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. A typical Device Configuration view is shown in Figure 7. Generally, this view includes a few fields that display device information as well as an Interface Configuration Table that lists interface parameters, some of which can be changed (see SPECTRUM Views). Some Device Configuration views include one or more buttons that provide access to device-specific configuration information. These are described below. Model Name Description Location Figure 7: File View Tools Bookmarks Contact Status Device Configuration View SpectroGRAPH: Model Name Contact Manufacturer Sys Up Time Configuration View Redundancy and Model Reconfiguration Options Sort Find Update Net Address Device Type Serial Number Number of Interfaces Interface Configuration Table Help Interface Address Translation Index Description Type Bandwidth Physical Addre IP Address of type Model of Landsape: Primary Device Management Page 19 Cisco Aironet Family

20 Configuration Views Device Configuration View Redundancy and Model Reconfiguration Options Refer to the SPECTRUM Views documentation Interface Address Translation Refer to the SPECTRUM Views documentation. Device Management Page 20 Cisco Aironet Family

21 Model Information View This section provides a brief overview of the Model Information view. Model Information views display administrative information about devices and their applications and let you set thresholds and alarm severity for the devices. Figure 8 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Model Name Description Location Figure 8: Model Information View SpectroGRAPH: Model Name File View Tools Bookmarks MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String DCM TimeOut DCM Retry Contact Manufacturer SysUpTime Model Information View Communication Information Net Address Device Type Serial Number General Information Condition Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Community Name Mgnmt Protocol Help Poll Interval Poll Status Log Ratio Last Successful Poll True Poll / Log Information Logged Polled IP Address of Model Type of Landscape: Primary Device Management Page 21 Cisco Aironet Family

22 Index A ACW-VLAN-CFG-MIB.my 15 Address Interface IP 10 Physical (MAC) 10 Translation 11 Admin Status 9 Aironet 5 AironetIOS 5 Applications 13 AWCVX-MIB.my 15 C CiscoCDPApp 16 Common Applications 14 Configuration Device 19 D Device Specific MIBs 15 DevTop Views 12 Discovery Application Cache Table View 16 Interface Discovery Status Table 17 Documentation 4 H Hardware 5 I Icon Subview documentation 6 Subviews 6 Icons Device 6 Interface 9 IF Configuration 10 Interface Type, Device 9 IOS-based firmware 5 L Line Statuses 18 M Management Tasks 7 Mask 11 MIB Support ACW-VLAN-CFG-MIB.my 15 AWCVX-MIB.my 15 Model Cisco 1100 series 5 Cisco 1200 Series 5 Cisco 1400 Series 5 Cisco 340 series 5 Cisco 350 Series 5 Information 21 Types of 5 N Network I/O ports 12 Network Type 10 P Performance Statistics 18 Port Number, Device 9 SPECTRUM Enterprise Manager Page 22 Cisco Aironet Family

23 Index Index S Serial ports 12 Supported Applications 14 T Threshold Information 10 Troubleshooting 7 V Viewing other documents 14 list 14 online 14 SPECTRUM Enterprise Manager Page 23 Cisco Aironet Family