Lucent Definity Supports Management Module SM-LUC1001

Transcription

1 Lucent Definity Titlepage Supports Management Module SM-LUC1001 Device Management

2 Copyright Notice Document Copyright 2002-present by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III(g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 Lucent Definity

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 TASKS 7 CLIENT VIEW 8 Switch Icon...9 Module Information View...9 Client Details...10 DEVICE TOPOLOGY VIEW 11 Interface Icon Subviews Menu Options...13 Interface Status View...13 Secondary Address Panel...13 APPLICATION VIEWS 14 Main Application View...14 Supported Applications...15 Common Applications...15 Device-Specific MIBs...16 G3Chassis Application View...16 Proxy Configuration...16 Client Table...17 PERFORMANCE VIEWS 19 Device Performance View...20 CONFIGURATION VIEWS 21 Device Configuration View Interface Configuration View MODEL INFORMATION VIEW 23 MANUAL MODELING 24 Map on Topology Connection Status...25 Location Icon Switch Icon INDEX 26 Device Management Page 3 Lucent Definity

4 Introduction This section introduces the SPECTRUM Device Management documentation for Lucent Definity Proxy Agent. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this documentation as a guide for managing Lucent Definity Proxy Agent with the SPECTRUM management module SM-LUC1001. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Lucent Definity Proxy Agent through software models in your SPECTRUM database. Information specific to the SM-LUC1001 is what is primarily included in this document. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How To Manage Your Network with SPECTRUM SPECTRUM Views Software Release Notes SPECTRUM Menus SPECTRUM Icons Management Module SRN Device Management Page 4 Lucent Definity

5 Introduction Supported Devices The SPECTRUM management module SM- LUC1001 currently allows you to model one type of Lucent Definity. The Lucent Definity Proxy Agent is a protocol conversion resource. The Proxy Agent software resides on a stand-alone personal computer and operates on the UnixWare Operation System. The main function is to convert management data from managed nodes and transmit the data to the management programs that reside of the Network Management System. The Proxy Agent supports both static and dynamic connections to managed nodes. You can assign up to 150 dynamic connections on the managed nodes screen. The Proxy Agent can support up to 30 connections which can be any combination of static and dynamic connections. The SPECTRUM Model The model type for the Lucent Definity device is LucentProxy. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. Supported Devices The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Model Name LucentProxy Small and Large Device Icons Large Device icon appears in Device Topology, Location, and Interface Device views. Small Device icon appears in Topology, Device Topology, Application, and Container views. Model Name LucentProxy Device Management Page 5 Lucent Definity

6 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. The SPECTRUM Model Model Information View (Page 23) Manual Modeling (Page 24) Option Fault Management Accesses the... For further information refer to How to Manage Your Network with SPECTRUM documentation. Client View Client View (Page 8) Device Topology Device Topology View (Page 11) Application Application Views (Page 14) Configuration Configuration Views (Page 21) Model Information Primary Application Model Information View (Page 23) Menu options that let you select either Gen Bridge App or MIB-II as the primary application. Note: Installing the DNM application will allow you to view the Data Network Management features. You can get these options by right clicking on the Device icon. This information is covered in Lucent documentation. The views listed below are accessible directly from this menu and are described individually in subsequent sections of this documentation. Client View (Page 8) Device Topology View (Page 11) Application Views (Page 14) Performance Views (Page 19) Configuration Views (Page 21) Device Management Page 6 Lucent Definity

7 Tasks This section lists device management tasks alphabetically and provides links to descriptions of the views and/or tables used to perform the task. Application Information (examine) Application Views (Page 14) Device Performance (monitor) Performance Views (Page 19) Enabling/Disabling a Port (examine) Admin. Status (Page 22) Model Information (examine) Model Information View (Page 23) Port Configuration (examine/modify) Interface Icon (Page 12) Device Configuration View (Page 21) Port Statistics (monitor) Device Performance View (Page 20) Device Management Page 7 Lucent Definity

8 Client View This section describes the Client view and subviews available for models of the Lucent Definity Proxy Agent in SPECTRUM. Access: From the Icon Subviews menu for the LucentProxy Device icon, select Client. This view (Figure 2) is a representation of the Private Branch Exchange (PBX) that the proxy has modeled. Each PBX can be classed into one of three categories: USA, with an enumerated state A custom category, where the name is supplied when the switch is added A generic category. Each icon in the lower panel (for a close-up, see Figure 3) represents a switch. Figure 2: Client View SpectroGRAPH: Route Device: JK2 File View Tools Bookmarks Help? Model Name Contact Description Location USA New Hampshire Sw0 idle dynamic 60 Sw2 idle dynamic 60 Network Address USA Rhode Island Sw1 down dynamic 60 Primary Application Berkshire Sw3 idle dynamic 60 System Up Time Manufacturer Device Type Serial Number Generic Sw4 idle dynamic 60 Note: The Client View is not updated immediately. To do so, go into the Model and Redundancy View (from Device Configuration View) and hit Reconfigure. Device Management Page 8 Lucent Definity

9 Client View Switch Icon Figure 3 shows an example of a switch icon from a Client view. (c) (d) a b c d e f Figure 3: Type Area (a) USA New Hampshire Sw0 idle dynamic 60 (e) Client Name Connection Status Connection Type Connection Timeout Switch Icon (b) (f) Switch Icon Type The class of switch. Valid values are: USA, Custom, and Generic. Area An enumerated value if Type is USA. Client Name The name of the client switch. Connection Status The status of the connection. Valid values are: idle, up, down, lost, and error. Connection Type The type of connection. Valid values are: dynamic, and static. Connection Timeout The number of idle minutes to wait before a dynamic connection is dropped. Module Information View Access: From the Icon Subviews menu for the Type/Area section of the Client View, select Information. Type The class of switch. Valid values are: USA, Custom, and Generic. Area An enumerated value if Type is USA. Device Management Page 9 Lucent Definity

10 Client View Client Details Clients The number of clients. Reconfigure Chassis Clicking this button will automatically reconfigure the chassis. Client Details Access: From the Icon Subviews menu for the Switch icon section of the Client View, select Client. Client Name The name of the client switch. Connection Type The type of connection. Valid values are: dynamic, and static. Connection Status The status of the connection. Valid values are: idle, up, down, lost, and error. Connection Timeout The number of idle minutes to wait before a dynamic connection is dropped. Device Management Page 10 Lucent Definity

11 Device Topology View This section provides brief descriptions of the Interface Device Topology view available for models of Lucent Definity Proxy Agent in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Device Topology. The Device Topology view (Figure 4) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. File Figure 4: Device Topology View SpectroGRAPH: Device Topology: JK2 View Tools Bookmarks Help JK2 LucentProxy 1 ON SFTWARLPBK lo0 0:0:0:0 2 ON other eee0 0:0:0:0 Device Management Page 11 Lucent Definity

12 Device Topology View Figure 5 shows a close-up of an Interface icon from an Interface Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 5: Interface Icon Client Details IF Status Label This label displays the current Operational Status of the interface (see Table 1). Note that the background color of the label also depends on the interface s current Administrative Status, which is set by the user. (See Interface Status View on Page 13.) This view can be accessed by doubleclicking this label. (a) (b) Table 1: Interface Status Label Colors g h i j k 1 ON SFTWARLPBK lo0 0:0:0:0 Interface Number Label IF Status Label Network Connection Interface Type Label IP Address Label (c) (d) (e) Interface Number Label This label displays the interface number. Color Operational Status Administrative Status Green ON ON ON Label Text Blue OFF OFF OFF Yellow OFF ON OFF Red Testing Test TST Network Connection The internal network connection to itself. Doubleclicking on this will open the Interface Configuration View (Page 22). Interface Type Label This label identifies the type of interface into the network. Double-clicking on this will open the Model Information View (Page 23). Device Management Page 12 Lucent Definity

13 Device Topology View IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel, which allows you to change the address and mask for this interface. Interface Icon Subviews Menu Options Table 2 lists the Icon Subviews menu options available for the Interface icon. Table 2: IF Status Interface Icon Subviews Menu Option Opens the... Interface Status View. IF Configuration Interface Configuration View (Page 22). Model Information Associated Model Information views for the selected interface (see Model Information View on Page 23). Interface Status View Client Details Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Status. This view provides information on the operational status of the interface and allows you to enable or disable the port. Operational Status The current state of the interface. Valid values are: On, Off, or Testing. Administrative Status This button allows you to select the desired operational state of the interface. Valid values are: On, Off, or Testing. Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. Device Management Page 13 Lucent Definity

14 Application Views This section describes the Application views and the associated application-specific subviews available for models of Lucent Definity Proxy Agent in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 6: Application View Main Application View SpectroGRAPH: Application: JK2 File View Tools Bookmarks Help When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 6 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. Model Name Contact Description Location Network Address Primary Application MIB-ll JK2 LucentProxy JK2_MIB-II celtix SNMP2_Agent g3chassis MP2-Agent g3chassis JK2_ICMP ICMPApp ICMP_App System Up Time Manufacturer Device Type Serial Number For more information on this view, refer to the MIBs and the Application View documentation. JK2_IP IP2_App IP2_App JK2_Syste System2_App ystem2_ap JK2_TCP TCP2_App TCP2_App Device Management Page 14 Lucent Definity

15 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Applications associated with non proprietary MIBs. See Common Applications below. Applications associated with device-specific MIBs. See Device-Specific MIBs (Page 16). Common Applications For the most part, these applications represent the non proprietary MIBs supported by your device. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Note: The documents listed below (in bold font) are available for viewing at: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - OSPF - OSPF2 - BGP4 - VRRP Bridging Applications - Ethernet Special Database - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation - QBridge MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Transmission Applications - FDDI - Point to Point - DS1 - DS3 - RS WAN Supported Applications Device Management Page 15 Lucent Definity

16 Application Views - Frame Relay - Token Ring - Ethernet - Fast Ethernet - rfc1317app - rfc1285app - rfc1315app App - SONET Technology Applications - APPN - ATM Client - DHCP - PNNI - rfc1316app - DLSw Device-Specific MIBs SPECTRUM imports the following device-level proprietary MIBs into its database: G3-LUCENT-MIB.mib These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Note: Supported Applications Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. A single device specific application exists for Lucent Definity Switch, g3chassis. G3Chassis Application View This major application (model type g3chassis) provides one application-specific subview, as follows. Proxy Configuration Access: From the Icon Subviews for the g3chassis icon, select Configuration. This view contains the following information: Proxy Agent A display string containing the release of the Proxy Agent. Agent Domain A display string containing the Domain Name of the Proxy Agent. Device Management Page 16 Lucent Definity

17 Application Views Default Custom Submap Name A display string that contains the default Submap Name used in administering managed node locations if the g3agentsubmaptype field is set to 'custom'. Default Submap State A display string containing a value that indicates the default state used in administering managed node locations if the g3agentsubmaptype field is set to 'usa'. Default Submap Type A display string object containing a value that indicates the default type of submap used in administering managed node locations ('generic', 'usa', or 'custom'). Client Table The Proxy Configuration view contains the Clien Table which provides the following information: External Name The External Name for a G3 client. Type The connection type for this G3 client. Valid values are: dynamic and static. Supported Applications Status The connection status for this G3 client. Valid values are: idle, up, down, lost, and error. Timeout The number of idle minutes to wait before a dynamic connection is dropped. Submap The default Submap Name used in administering managed node locations. Table 3 displays the valid submaps and descriptions. Submap Generic(0) USA(1) Custom(2) Table 3: Submap Description The switch is in the generic category. The g3clientstate is enumerated to which state the switch is in. The g3clientsubmapname is a text string with the name of the custom category in it. State A numeric value representing the state in which to place the managed node icon on the NMS if Submap is set to USA (Alabama = 0, Alaska = 1,... Wyoming = 49). Device Management Page 17 Lucent Definity

18 Application Views Supported Applications Custom A custom category where the name is supplied when the switch is added. Device Management Page 18 Lucent Definity

19 Performance Views This section provides brief descriptions of the Performance views available for models of Lucent Definity Proxy Agent in SPECTRUM. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 7. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 7: Device Performance View SpectroGRAPH : IP Address_EthernetApp File View Tools Bookmarks Help Name Contact Description Location Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. 0:40:0 0:30:0 0:20:0 Log Value Average Peak Value Load * Packet Rate % Error % Discarded Graph Properties Scroll to Date-Time Transmit Detail Receive Config Threshold Alarms Events For more information on Performance views, refer to the SPECTRUM Views documentation. Device Management Page 19 Lucent Definity

20 Performance Views Device Performance View Device Performance View Access: From the Icon Subviews menu for the Device icon, select Device Performance. This view (Figure 7) includes both a graph and a table that show current, average, and peak values for the performance statistics. The view also provides button access to the Enterprise Alarm Manager, Event Log, Interface Threshold View, Interface Configuration View (Page 22), Transmit and Receive statistics, and pie charts. Device Management Page 20 Lucent Definity

21 Configuration Views This section describes the various Configuration views and subviews available for models of Lucent Definity Proxy Agent in SPECTRUM. Configuration views allow you to view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of SM-LUC1001 devices: Device Configuration View Interface Configuration View (Page 22) Device Configuration View Access: From the Icon Subviews menu for the LucentDefinity Device icon, select Configuration. Figure 8 provides status and configuration information about the device as a whole as well as on a port-by-port basis. It also provides button access to an Interface Address Translation table and a subview that lets you establish redundancy for the model. Fields and column headings within the Device Configuration view and its subviews are explained in detail in SPECTRUM Views. Figure 8: File View Tools Bookmarks Model Name Contact Description Location Sort Find Update Device Configuration View SpectroGRAPH: Model Name Device Configuration View Network Address System Up Time Manufacturer Device Type Primary Application Serial Number Interface Configuration Table Index Type Physical Address Max Frame Size Operational Status Model Name of type LucentProxy of Landscape node: Primary Print Help Device Management Page 21 Lucent Definity

22 Configuration Views Interface Configuration View Interface Configuration View Access: From the Icon Subviews menu for a selected Interface icon in the Interface Device view, select Interface Configuration. Column headings are provided below for the selected interface: Operation Status The current operational state of the interface. Valid values are: Up, Down, or Testing. Admin. Status The desired operational state of the interface. Valid values are: Up, Down, or Testing. IP Address/Network Mask This window provides a list of the user-defined names and IP addresses for the interface. Packet Size The largest packet that can be transmitted or received by the port, displayed in octets. Device Management Page 22 Lucent Definity

23 Model Information View This section provides a brief overview of the Model Information view. This view displays administrative information about the device and its applications and lets you set thresholds and alarm severity for the device. Figure 9 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Figure 9: Model Information View SpectroGRAPH: JK2 File View Tools Bookmarks Help? Name Contact Description Location Primary Address Model Information View Network Address Primary Application System Up Time Manufacturer User-Defined Type Device Type Serial Number General Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Communication Information DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status Last Successful Poll LOGGED POLLED Device Management Page 23 Lucent Definity

24 Manual Modeling This section provides a brief description of how to manually model the Lucent Definity in SPECTRUM. There are two ways to manually model the Lucent Definity in SPECTRUM: By Model Type. When you model by model type, the Creation view appears. From here, you can choose to turn off the Map on Topology option. The default is Yes, indicating that you want the location icons and switches displayed. By IP. When modeling by IP, the Map on Topology option is always Yes. Map on Topology Figure 10 shows a representation of mapping the switches onto the topology view. If the Map on Topology option were No, only the Lucent Proxy icon would show up in the Topology view. USA Rhode Island R1 Figure 10: Map on Topology JK2 LucentProxy Location Icons Switches Lucent Proxy USA New Hampshire b36 Device Management Page 24 Lucent Definity

25 Manual Modeling Connection Status The status between the Lucent proxy and the switch. Table 4 describes the possible connections statuses: Table 4: Connection Status Connection Status Description Switch Icon Map on Topology The Switch icon displays the switches in your topology. Right clicking on the Switch icon brings up the Icon Subviews menu. Selecting Configuration will then bring the Client Details (Page 10). You can also access this by doubleclicking the down arrow of the Switch icon. Dark Green Light Green Yellow Red Orange Idle state. Connection has been made. Trying to connect the trap. Connection has failed. Unidentifiable error. Location Icon The Location icon allows you to place your switches into different groups, based on location. Right clicking on the Location icon brings up the Icon Subviews menu. Selecting Information will bring up the Module Information View (Page 9). Device Management Page 25 Lucent Definity

26 Index A Address Translation table 13 Admin. Status 22 Administrative Status 13 Application Views 14 C Client Details 17 Colors Interface Status Label 12 Configuration Views 21 Configuration views 21 Connection Status 25 D Device Configuration View 21 Devices supported by this module 5 E Enterprise Alarm Manager 20 Event Log 20 I Icon Subviews Menus for Interface icon 13 Icons Interface 12 Interface Configuration View 22 Interface icon 12 Interface Icon Subviews Menu Options 13 Interface Number Label 9 Interface Status View 13 Administrative Status 13 Operational Status 13 IP Address/Network Mask 22 L Labels Interface IF Status Label 12 Interface Number Label 12 Interface Type Label 12 Location Icon 25 M Map on Topology 24 MIB-ll Performance View 20 Model 23 Information 23 Model Information View 23 Module Information 19 N Network I/O ports 11 O Operation Status 22 Operational Status 13 P Packet Size 22 Performance Views 19 Physical Address 22 Purpose and Scope 4 Device Management Page 26 Lucent Definity

27 Index Index R Required Reading 4 S Secondary Address Panel 13 Serial ports 11 SPECTRUM Model 5 State 17 Supported Devices 5 Switch Icon 25 T Transmit and Receive statistics 20 V VA{ LANE and Outbound Performance View 21 Views Configuration 21 Device Configuration 21 Device Performance 20 Interface Configuration 22 Interface Status 13 Device Management Page 27 Lucent Definity

28 Index Index Device Management Page 28 Lucent Definity