SPECTRUM Enterprise Manager. Device Management. Titlepae. Cisco 6400 DSL. Supports Management Module SM-CIS1010

Transcription

1 SPECTRUM Enterprise Manager Device Management Titlepae Cisco 6400 DSL Supports Management Module SM-CIS1010

2 Notice Aprisma Management Technologies, Inc. (Aprisma), reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Aprisma to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Copyright January 2001 by Aprisma Management Technologies. All rights reserved. Printed in the United States of America. Order Number: Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH SPECTRUM, thespectrum IMT/VNM logo, DCM, IMT, andvnm are registered trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, andvirtual Network Machine are trademarks of Aprisma or its affiliates. Ethernet is a trademark of Xerox Corporation. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the Licensed Software is virus-free. Aprisma has tested its software with current virus checking technologies. However, because no anti-virus system is 100% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence. Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise expressly stated in the contract. (b) This computer software may be: (1) Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred; (2) Used or copied for use in a backup computer if any computer for which it was acquired is inoperative; (3) Reproduced for archival or backup purposes; (4) Modified, adapted, or combined with other computer software, provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights; (5) Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and (6) Used or copied for use in or transferred to a replacement computer. (c) Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosure prohibitions, with the minimum rights set forth in paragraph (b) of this clause. (d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract. (e) This Notice shall be marked on any reproduction of this computer software, in wholeorinpart. SPECTRUM Enterprise Manager Page2 Cisco 6400 DSL

3 Contents INTRODUCTION 5 Purpose and Scope...5 Required Reading...5 Supported Devices...6 The SPECTRUM Model...6 TASKS 8 Administrative Information (check)...8 Alarm Thresholds (set)...8 Configuration Information (check)...8 IP Address (find/change)...8 Network Type (check)...8 Performance (check)...8 Port Status (check/change)...8 Topology (check)...8 DEVICE VIEW 9 Interface Icons...10 Interface Icon Subviews Menu...11 Interface Status View...12 Secondary Address Panel...12 DEVICE TOPOLOGY VIEW 13 APPLICATION VIEWS 14 Main Application View...14 Supported Applications...15 Common Applications...15 Device-Specific Applications...16 Cisco System Log Application...17 System Log Basic View...17 Cisco System Log History Table View...18 Cisco Chassis Application...18 Cisco Chassis Card View...18 Cisco Chassis General Information View...19 Chassis Information...19 ROM Information...20 RAM Information...20 Cisco Ping Application...20 Ping Request Table View...20 Cisco Queue Application...22 Queue Interface View...22 Queue Statistics View...23 Queue Rotation Interface View...23 Cisco VPDN Application View...23 Cisco CDP Application...24 Discovery Cache Table View...24 Interface Discovery Status Table...24 Cisco Interface Application...25 Cisco IfceApp Configuration View...25 Cisco Memory Pool Application...25 Memory Pool Monitor View...25 SPECTRUM Enterprise Manager Page3 Cisco 6400 DSL

4 CHASSIS ALARM VIEW 27 PERFORMANCE VIEWS 28 Device Performance View...29 Port Performance View...29 CONFIGURATION VIEWS 30 Device Configuration View...30 Interface Configuration View...31 MODEL INFORMATION VIEW 32 INDEX 33 SPECTRUM Enterprise Manager Page4 Cisco 6400 DSL

5 Introduction This section introduces the SPECTRUM Device Management documentation for the Cisco 6400 Series Access Concentrator. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 6) The SPECTRUM Model (Page 6) Purpose and Scope Use this document as a guide for managing the Cisco devices described on Page 6 with SPECTRUM management module SM-CIS1010. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Cisco 6400 devices through software models in your SPECTRUM database. Information specific to SM-CIS1010 is what is primarily included in this document. For general information about device management using SPECTRUM and explanations of SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice SPECTRUM Enterprise Manager Page5 Cisco 6400 DSL

6 Introduction Supported Devices SPECTRUM management module SM-CIS1010 currently lets you model the Cisco Series Access Concentrator. The Cisco 6400 Series Access Concentrator carrier-class broadband aggregator is a scalable service gateway that enables the selection and delivery of broadband network services, virtual private networks (VPNs) and voice and entertainment driven traffic over the full suite of access media. The SPECTRUM Model Supported Devices The model type for the Cisco 6400 devices is Cisco6400_DSL. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 8. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Device Icons Model Name Small Device icon appears in Topology and Application views Cisco6400_DSL LargeDeviceiconappearsin Device Topology, Location, and Device Interface views. Model Name Cisco6400_DSL SPECTRUM Enterprise Manager Page6 Cisco 6400 DSL

7 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Device Device View (Page 9) Accesses the... Device Topology Device Topology View (Page 13) Application Application Views (Page 14) Chassis Alarm Chassis Alarm View (Page 27) Configuration Configuration Views (Page 30) Model Information Primary Application Model Information View (Page 32) Menu options that let you select either Gen Bridge App or MIB-II as the primary application. The SPECTRUM Model The rest of this document covering the Cisco 6400 management module is organized as follows. Tasks (Page 8) Device View (Page 9) Device Topology View (Page 13) Application Views (Page 14) Chassis Alarm View (Page 27) Performance Views (Page 28) Configuration Views (Page 30) Model Information View (Page 32) SPECTRUM Enterprise Manager Page7 Cisco 6400 DSL

8 Tasks This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information View (Page 32) Alarm Thresholds (set) Interface Icon Subviews Menu (Page 11) Port Status (check/change) Interface Status View (Page 12) Topology (check) Device Topology View (Page 13) Configuration Information (check) Configuration Views (Page 30) IP Address (find/change) Device View (Page 9) Secondary Address Panel (Page 12) NetworkType(check) Network Type Label (Page 11) Performance (check) Device View (Page 9) Interface Icons (Page 10) Performance Views (Page 28) SPECTRUM Enterprise Manager Page8 Cisco 6400 DSL

9 Device View This section describes the Device view and subviews available for models of Cisco 6400 Series Access Concentrator devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Device. This view (Figure 2) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 2: Device View SpectroGRAPH: Router Device: Model Name File View Tools Bookmarks Help Model Name Contact Description Location Model Name Cisco6400_DSL 1 ON Ethernet ei0 0:0:1D:F:FD:B6 2 ON ATM CPU Network Address Primary Application Gen Bridge App Filter Physical Interface Description Device Icon 3 ON 4 ATM 7B2 Sys Up Time Manufacturer Device Type Serial Number Interface Options Panel ATM 8B3 ON 5 ON SFTWARLPBK lo0 0:0:1D:F:FD:B6 6 ON ATM port CPU.1 7 ON ATM 7B3 8 ON ATM 8B4 9 ON ATM8023 zn1 0:0:1D:F:FD:B6 512 ON AAL5 UAAL5 10 ON ATM 7A1 ON ATM 7B ON ATM 8B1 ON ATM 8B2 Interface Icons Model Name of type Cisco_6400DSL of Landscape node: Primary SPECTRUM Enterprise Manager Page9 Cisco 6400 DSL

10 Device View Interface Icons Interface Icons Figure 3 shows a close-up of an Interface icon from the Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 3: a Interface Icon b Interface Number Label This label displays the interface (port) number. IF Status Label This label displays the current status of the interface for the primary application selected, e.g., Gen Rtr App or MIB-II App. Table 1 lists the possible label color representations. Note that the color of the label also depends on the interface s current Administrative Status, which you set in the Interface Status View (Page 12). This view can be accessed by double-clicking the label. a b c d e f g 1 ON Table 1: Interface Status Label Colors ethernet c fxp0 d Operational Administrative Label Color Status Status Text 0:0:1D:F:FD:B6 e 1 f g Green up up ON Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label Gauge Label Blue down down OFF Yellow down up OFF Red testing testing TEST Interface Type Label This label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Configuration View (Page 31). SPECTRUM Enterprise Manager Page10 Cisco 6400 DSL

11 Device View Interface Icon Subviews Menu Network Type Label This label identifies the type of network to which the interface is connected. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the IF Address Translation Table. IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 12), which lets you change the address and mask for the interface. Gauge Label This label displays whichever performance statistic has been selected in the Gauge Control Panel for this device s interfaces. (Refer to the SPECTRUM Views documentation for information about the Gauge Control Panel.) Double-click this label to open the Port Performance View (Page 29). Interface Icon Subviews Menu Table 2 lists the device-specific interface Icon Subviews menu options and the views to which they provide access. Detail Table 2: Option Interface Icon Subviews Menu Accesses the... Interface Detail view, which displays packet, error, and discard breakdown statistics for the interface. IF Status Interface Status View (Page 12). IF Configuration Interface Configuration View (Page 31). IF Address Translation Table Secondary Address Panel Thresholds Model Information Interface Address Translation Table, which identifies the physical and network address for the interface. Secondary Address Panel (Page 12). Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface. Model Information View (Page 32). SPECTRUM Enterprise Manager Page11 Cisco 6400 DSL

12 Device View Interface Status View Interface Status View Access: From the Icon Subviews menu for the Interface icon in the Device view, select IF Status. This view provides information on the operational status of the interface and allows you to enable or disable the port. Operational Status The current state of the interface (Up, Down, Unknown, Dormant, Not Present, Lower Layer Down, or Testing). Administrative Status This button allows you to select the desired administrative state of the interface (On, Off, or Testing). Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. SPECTRUM Enterprise Manager Page12 Cisco 6400 DSL

13 Device Topology View This section describes the Device Topology view available for models of the Cisco 6400 Series Access Concentrator devices. Access: From the Icon Subviews menu for the Device icon, select Device Topology. The Device Topology view (Figure 4) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device View (Page 9). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 4: Device Topology View SpectroGRAPH: Device Topology: Model Name File View Tools Bookmarks Help Graphic of <manufacturer> Device Model Name Cisco6400_DSL 1 ON 2 ON 3 ON Ethernet ei0 0:0:1D:F:FD:B6 ATM A2 0:0:1D:F:FD:B6 ATM CPU 0:0:1D:F:FD:B6 Model Name of type Model Type of Landscape node: Primary SPECTRUM Enterprise Manager Page13 Cisco 6400 DSL

14 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Cisco 6400 Series Access Concentrator devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 5: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View documentation. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Contact Description Location NetworkAddress System UpTime Manufacturer Device Type Serial Number Model Name Cisco6400_DSL 6E132_25 Help Model Name of type <model type> of Landscape node: Primary SPECTRUM Enterprise Manager Page14 Cisco 6400 DSL

15 Application Views Supported Applications Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Common Applications, below Device-Specific Applications (Page 16) Common Applications For the most part, these applications represent the non proprietary MIBs supported by your device. Listed below (beneath the title of the document that describes them) are some of the common applications currently supported by SPECTRUM. Note: The documents listed are available for viewing at: Bridging Applications - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - Open Shortest Path First MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Miscellaneous Applications - FDDI - Point to Point - DS 1 - RS WAN - Frame Relay - Token Ring - DLSW - APPN - Ethernet - Fast Ethernet - ATM Client - DHCP SPECTRUM Enterprise Manager Page15 Cisco 6400 DSL

16 Application Views Supported Applications Device-Specific Applications SPECTRUM imports the following device-level proprietary MIBs into its database: OLD-CISCO-CPU-MIB.my OLD-CISCO-INTERFACES-MIB.my OLD-CISCO-IP-MIB.my OLD-CISCO-MEMORY-MIB.my CISCO-ENVMON-MIB.my OLD-CISCO-SYS-MIB.my OLD-CISCO-SYSTEM-MIB.my OLD-CISCO-TS-MIB.my CISCO-CDP-MIB.my CISCO-CONFIG-MAN-MIB.my CISCO-FLASH-MIB.my CISCO-GENERAL-TRAPS.my CISCO-IMAGE-MIB.my CISCO-MEMORY-POOL-MIB.my CISCO-PING-MIB.my CISCO-PRODUCTS-MIB.my CISCO-SMI.my CISCO-TC.my CISCO-ATM-ADDR-MIB.my CISCO-ATM-CONN-MIB.my CISCO-ATM-IF-MIB.my CISCO-ATM-IF-PHYS-MIB.my CISCO-ATM-RM-MIB.my CISCO-ATM-SERVICE-REGISTRY-MIB.my CISCO-ATM-SWITCH-ADDR-MIB.my CISCO-ATM-TRAFFIC-MIB.my CISCO-RHINO-MIB.myMIB 2 ditto These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. The views and subviews for the Cisco 6400_DSL specific applications are described in the rest of this section, grouped by major applications as listed below: Cisco System Log Application (Page 17) Cisco Chassis Application (Page 18) Cisco VPDN Application View (Page 23) Cisco CDP Application (Page 24) Cisco Interface Application (Page 25) Cisco Memory Pool Application (Page 25) SPECTRUM Enterprise Manager Page16 Cisco 6400 DSL

17 Application Views Cisco System Log Application Cisco System Log Application This application (CiscoSYSLog) provides information on all notifications and messages received by this device. The following views are available with this application: System Log Basic View (Page 17) Cisco System Log History Table View (Page 18) System Log Basic View Access: From the Icon Subviews menu for the CiscoSysLog, select Basic. Notifications Sent The number of clogged messages that have been sent. This number may include notifications that were prevented from being transmitted due to reasons such as resource limitations or nonconnectivity. If one is receiving notifications, on can poll this object to determine if any notifications were missed. If so, a poll of the History Table might be appropriate. Notifications Enabled Indicates whether messages will be generated or not. Max Severity Level Indicates which system log severity level will be processed. Any system log message with a severity level greater than the one displayed will be ignored by the agent. Severity decreases as the number increases, i.e. error (4) is less than debug (8). Messages Ignored The number of system log messages that were ignored. A message will be ignored if has a severity less than specified by the Max Severity Level. Messages Dropped The number of system log messages that were dropped to insufficient system resources. Most likely this will occur at the same time that the system log messages are generated to indicate the lack of resources. Increases in this fields value may serve as an indication that the system resource level should be examined via other mib objects. A message that is dropped will not appear in the history table and no notification will be sent for this message. SPECTRUM Enterprise Manager Page17 Cisco 6400 DSL

18 Application Views Cisco Chassis Application Cisco System Log History Table View Access: From the Icon Subviews menu for the Cisco Syslog device icon, select History. The Cisco System Log History table provides information on the messages received on this device. When the table is full the oldest entry is deleted to make room for the newest message received. The following information is available with this view: Max Table Length The number of messages that will be listed. Messages flushed The number of messages that have been removed from the History table in order to make room for new messages. Index An increasing integer for the sole purpose of indexing the number of messages received by this table. When it reaches the maximum value the agent flushes the table and wraps the value back to one. Facility Name of the facility that generated the message. Severity The severity of the message. Message Name A textual identification of the message type. A facility name in conjunction with a message name uniquely identifies a message type. Message Text The textual body of the message sent. If the message is longer than 255 characters a * will appear informing you that the message has been truncated to 254 characters. Time Stamp The value of the SysUpTime when the message was sent. Cisco Chassis Application This application (CiscoChasApp) has two menu options that provide access to the following views. Cisco Chassis Card View (Page 18) Cisco Chassis General Information View (Page 19) Cisco Chassis Card View Access: From the Icon Subviews menu for the CiscoChasApp Application icon, select Card Information. SPECTRUM Enterprise Manager Page18 Cisco 6400 DSL

19 Application Views Cisco Chassis Application This view provides information on the cards contained in the chassis. Slot The slot number in which this card is installed. If the slot number is not applicable or not determinable, this field will display. Type The functional type of the card installed in this slot. Description A textual description of this card. Software Ver. The version number of the firmware installed on this card. If no version number is available, this field will remain empty. Hardware Ver. The hardware revision level of this card. If no revision level is available, this field will remain empty. Serial No. The serial number of this card. If no serial number is available, this field will contain a zero. Cisco Chassis General Information View Access: From the Icon Subviews menu for the CiscoChasApp Application icon, select General. This view displays information on the chassis in which the router is installed. This view is divided into the three sections described below. Chassis Information This section of the Chassis General Information view provides the following physical information about the chassis. Hardware Revision Level The version number of the chassis hardware. If the version number is not available, this field will remain empty. Chassis Type The type of chassis. Possible chassis types are: Unknown, Multibus, Agsplus, Igs, c2000, c3000, c4000, c7000, cs-500, c7010, c2500, and c4500. Chassis ID/Serial No. A numerical identifier for this chassis. The default value is the serial number of the chassis. If no serial number is available and no alternative ID SPECTRUM Enterprise Manager Page19 Cisco 6400 DSL

20 Application Views Cisco Chassis Application has been set for the chassis, this field will remain empty. Number of Chassis Slots The number of slots in this chassis model. ROM Information This section of the Chassis General Information View provides the following information about the ROM installed in the chassis: ROM Monitor Version The version number of the ROM monitor. ROM Software Version The version number of the ROM system software. If no version number is available, this field will remain empty. Config Register The current value of the configuration register. RAM Information This section of the Chassis General Information View provides the following information about the RAM installed in the chassis: System CPU RAM (bytes) The amount of RAM available to the CPU, in bytes. Non-volatile RAM Used (bytes) The amount of non-volatile configuration memory in use, in bytes. Non-volatile RAM Size (bytes) The total size, in bytes, of non-volatile configuration memory. Cisco Ping Application This application (CiscoPingApp) provides access to the Ping Request Table View. Ping Request Table View Access: From the Icon Subviews menu for the CiscoPingApp Application icon, select Ping Request Entry Table. This view allows you to update the ping request list for this device. The following information is available for this view: Owner The user who configured this entry. Protocol The protocol to use once an instance of this object is created e.g., Novell, Apple Talk, Vines, etc. Address The address of the device to be pinged. SPECTRUM Enterprise Manager Page20 Cisco 6400 DSL

21 Application Views Cisco Chassis Application Status The status of this table entry. Possible states are: active, notinservice, notready, createandgo, createandwait, and destroy. Pkt Cnt Specifies the number of ping packets to send to the target device in this sequence. Pkt Sz Specifies the size of ping packets to send to the target device in this sequence. Pkt Timeout Specifies the amount of time to wait for a response to transmitted packet before declaring the packet dropped. Delay Specifies the minimum amount of time to wait before sending the next packet in a sequence after receiving a response or declaring a timeout for a previous packet. Trap On Specifies whether or not a ciscopingcompletion trap should be issued on completion of the sequence of pings. Pkts Sent The number of ping packets that have been sent to the target. Pkts Rcvd The number of ping packets that have been received from the target in this sequence. Min RTT The minimum round trip time in milliseconds of all the packets that have been sent in this sequence. Avg RTT The average round trip time in milliseconds of all the packets that have been sent in this sequence. Max RTT The maximum round trip time in milliseconds of all the packets that have been sent in this sequence. Completed Indicates (true) that all the packets in this sequence have been either responded to or timed out. SPECTRUM Enterprise Manager Page21 Cisco 6400 DSL

22 Application Views Cisco Chassis Application AddanEntry This button opens the Add Ping Request dialog box. Enter the following information and click the Add Request button to add an entry to the Ping Request Entry Table: Address Owner Packet Count Packet Size Packet Timeout Delay Protocol Trap on Completion Cisco Queue Application This application (CiscoQueueApp) has three menu options that provide access to the information used to manage interface queuing within this device. Queue Interface View (Page 22) Queue Statistics View (Page 23) Queue Rotation Interface View (Page 23) Queue Interface View Access: From the Icon Subviews menu for the CiscoQueueApp Application icon, select Queue Interface. This view provides the following information on the queues for a particular Cisco interface. IF The IF index for this interface. Type The type of queuing used in the hold queue. MaximumNumberofMsgs The maximum number of messages placed in the hardware transmission queue. Number of Sub-Queues The number of sub-queues from which the hold queue is built. SPECTRUM Enterprise Manager Page22 Cisco 6400 DSL

23 Application Views Cisco VPDN Application View Queue Statistics View Access: From the Icon Subviews menu for the CiscoQueueApp Application icon, select Queue Statistics. This view provides the following statistical information on the queues for a particular Cisco interface. Sub-Queue Attrs A list of sub-queue attributes for an interface. Number of Msgs The number of messages in the sub-queue. Maximum Permitted Msgs The maximum number of messages permitted in the sub-queue. Number of Msgs Discarded The number of messages discarded from this queue since restart. Queue Rotation Interface View Access: From the Icon Subviews menu for the CiscoQueueApp Application icon, select Rotation Interface. This view provides the following information on the rotation of custom queues for a particular Cisco interface. Statistics Queue Number Custom queuing sub-queue attributes for an interface. Number of Transmitted Octets The number of octets that may be transmitted from a custom queuing sub-queue before it must yield to another queue. CiscoVPDNApplicationView This major application provides information on Virtual Private Dialup Networks (VPDNs) which handle the forwarding of PPP links from and Internet Protocol to a Home Gateway. For more information on this application refer to the Cisco VPDN Application documentation. SPECTRUM Enterprise Manager Page23 Cisco 6400 DSL

24 Application Views Cisco CDP Application Cisco CDP Application This view provides discovery information for the selected device. This application provides two tables: The Discovery Cache Table and the Interface Discovery Status Table as described below. Discovery Cache Table View Access: From the Icon Subviews menu for the CDP Application icon, select Cache. This view provides the information received by the Cisco Discovery Protocol (CDP). This table provides the following information: Type Display the type of address contained in the corresponding Address field described below. Address Displays the network layer of the device s SNMPagent as reported in the most recent CDP message. Device ID Displays the Device-ID. A zero indicates no Device-ID was reported. Device Port Displays the Port-ID. A zero indicates no Port-ID was reported. Platform Displays the devices hardware platform. Capabilities Displays the devices functional capabilities. Interface Discovery Status Table Access: From the Icon Subviews menu for the CDP Application icon, select Interface. This table contains the status of Cisco Discovery Protocol (CDP) on the device s interfaces. This table provides the following information: Discovery Displays information about the type of devices in the network, configuration information about the links connecting those devices, and the number of interfaces within each device. Group Displays the group number of the repeater number of the repeater port which corresponds to this interface. Port Displays the port number of the repeater port which corresponds to this interface. SPECTRUM Enterprise Manager Page24 Cisco 6400 DSL

25 Application Views Cisco Interface Application Interval Displays the interval at which the CDP messages are to be generated on this interface. The default value is 60. Cisco Interface Application The Cisco Interface Application provides access to application-specific Configuration view. Cisco IfceApp Configuration View Access: From the Icon Subviews menu of the CiscoIFApp icon, select Configuration. The CiscoIFApp Configuration opens giving you the choices to Create Interface application and/or Create Sub Interface applications. Cisco Memory Pool Application Memory pools can be roughly categorized into two groups, predefined pools and dynamic pools. The following pool types are currently predefined: processor memory i/o memory pci memory fast memory multibus memory Dynamic pools will have a pool type value greater than any of the predefined types listed above. Note that only the processor pool is required to be supported by all devices. Support for other pool types is dependent on the device being managed. Memory Pool Monitor View Access: From the Icon Subviews menu for the Cisco Memory Pool Application icon, select Memory Pool Monitor. This view allows you to monitor the memory available for this device. This view contains the following information: Name A name assigned to the memory pool. Alternative Indicates whether or not this memory pool has an alternate pool configured. Alternate pools are used for fallback when the current pool runs out of memory. SPECTRUM Enterprise Manager Page25 Cisco 6400 DSL

26 Application Views Cisco Memory Pool Application Valid Indicates whether or not the remaining objects in this entry contain accurate data. If an instance of this object has the value false the values of the remaining objects in the conceptual row may contain inaccurate information (specifically, the reported values may be less than the actual values). Used Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device. Free Indicates the number of bytes, from the memory pool, that are currently unused on the managed device. Note that the sum of ciscomemory PoolUsed and ciscomemorypoolfree is the total amount of memory in the pool. Largest Free Indicates the largest number of continuous bytes, from the memory pool that are currently unused on the managed device. SPECTRUM Enterprise Manager Page26 Cisco 6400 DSL

27 Chassis Alarm View This section provides brief descriptions of the Chassis Alarm view for the Cisco 6400 Series Access Concentrator devices in SPECTRUM. The Chassis Alarm view provides you with the Chassis Alarm table which maintains information on all alarms that have occurred on the device. The Chassis Alarm view displays the source, the type, the severity, and the status of all the alarms associated with this device. Figure 6 is an example of the Chassis Alarm view. Figure 6: FileView Tools Bookmarks Model Name Contact Description Location Chassis Alarm View SpectroGRAPH: Model Name Chassis Alarm View Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Help Sort Find Update Chassis Alarm Table Print Index Source Type Severity Status Model Name of type Cisco_6400DSL of Landscape node: Primary SPECTRUM Enterprise Manager Page27 Cisco 6400 DSL

28 Performance Views This section provides brief descriptions of the Performance views available for the Cisco 6400 Series Access Concentrator devices in SPECTRUM. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 7. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. For more information on Performance views, refer to the SPECTRUM Views documentation. The following paragraphs list the performance attributes displayed for each Performance view supported by this management module. Figure 7: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Model Name Contact Description Location Network Address Primary Application System UpTime Manufacturer Device Type Serial Number Value Average Peak Value Log *FrameRate % Delivered % Forwarded %Transmit % Error %Discarded 0:40:0 0:30:0 0:20:0 0 *Frames per second Graph Properties Scroll to Date-Time Detail type routing of type IP Routing of Landscape node: Primary SPECTRUM Enterprise Manager Page28 Cisco 6400 DSL

29 Performance Views Device Performance View Device Performance View Access: From the Icon Subviews menu for the Device icon, select Performance. Current and historical frame transmission information is provided via the following attributes. Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded Port Performance View Access: From the Icon Subviews menu for the Device Interface icon, select Performance. Current and historical packet transmission information is provided via the following attributes. Load Packet Rate % Error % Discarded SPECTRUM Enterprise Manager Page29 Cisco 6400 DSL

30 Configuration Views This section describes the various Configuration views available for models of the Cisco 6400 Series Access Concentrator devices in SPECTRUM. Configuration views let you view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Cisco 6400 devices: Device Configuration View (Page 30) Interface Configuration View (Page 31) Figure 8: File View Tools Bookmarks Model Name Contact Description Location Device Configuration View SpectroGRAPH: Model Name Device Configuration View Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Help Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. This view (Figure 8) provides status and configuration information about the device as a whole as well as on a port-by-port basis. Fields and column headings within the Device Configuration view and its subviews are explained in detail in the SPECTRUM Views documentation. Interface Configuration Table Sort Find Update Index Type Physical Address Max Frame Size Operational Status Model Name of type Cisco6400_DSL of Landscape node: Primary Print SPECTRUM Enterprise Manager Page30 Cisco 6400 DSL

31 Configuration Views Interface Configuration View Interface Configuration View Access: From the Icon Subviews menu for an Interface icon in the Device view, select IF Configuration. This view provides the following information for the selected interface: Operation Status The current operational state of the interface (Up, Down, Unknown, Dormant, Not Present, or Lower Layer Down). do not vary in bandwidth, or no accurate estimate can be made, a nominal bandwidth is provided. Packet Size The largest packet that can be transmitted or received by the port, displayed in octets. Queue Length The length of the outbound packet queue, in packets. Admin. Status The desired operational state of the interface (up, down, or testing). Last Change The System UpTime value when the interface entered its current operational state. IP Address/Network Mask This window provides a list of the user-defined names and IP addresses for the interface. Physical Address The Ethernet (MAC) address of the interface. Bandwidth The estimated bandwidth of the interface, measured in bits per second. For interfaces that SPECTRUM Enterprise Manager Page31 Cisco 6400 DSL

32 Model Information View This section provides a brief overview of the Model Information view. This view displays administrative information about the device and its applications and lets you set thresholds and alarm severity for the device. Figure 9 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Model Name Contact Description Location Figure 9: File View Tools Bookmarks Model Information View SpectroGRAPH: Model Name Model Information View Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Help General Information MM Name MM Part Number MMVersion Number Model Type Model Creation Time Model Created By Model State Security String Condition Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Communication Information DCM TimeOut DCM Retry Community Name Poll/Log Information Poll Interval Polling Status Last Successful Poll Log Ratio LOGGED POLLED type Model Type of Landscape: Primary SPECTRUM Enterprise Manager Page32 Cisco 6400 DSL

33 Index A Add an Entry button 22 Address Interface IP 11 Physical (MAC) 11 Translation 12 Admin Status 10, 31 Applications 14 B Bandwidth 31 C Chassis ID/Serial No. 19 Information 19 Type 19 Chassis Application 18 Chassis Card View 18 Chassis General Information View 19 RAM Information 20 ROM Information 20 Cisco Chassis Card View 18 General Information View 19 Cisco Chassis Card View 18 Cisco Chassis General Information View 18 CiscoChasApp 18 CiscoPingApp 20 Config Register 20 Configuration Device 30 Interface 31 D Description 19 DevTop Views 13 Documentation 5 G Gauge Label 11 H Hardware 6 Revision Level 19 Ver. 19 I Icons Device 6 Interface 10 Interface Status 12 Type, Device 10 IP Address/Network Mask 31 L Last Change 31 M Management Tasks 8 Mask 12 Model SPECTRUM Enterprise Manager Page33 Cisco 6400 DSL

34 Index Information 32 Types of 6 N Network I/O ports 13 Network Type 11 Non-volatile RAM Size (bytes) 20 Used (bytes) 20 Number of Chassis Slots 20 O Operation Status 31 P Packet Size 31 Performance Statistics 11, 28 Physical Address 31 Ping Application 20 Ping Request Table View 20 Port Number, Device 10 Q Queue Application 22 Queue Interface View 22 Queue Length 31 Queue Rotation Interface View 23 Queue Statistics View 23 R RAM Information 20 Restricted Rights Notice 2 ROM Information 20 Monitor Version 20 Software Version 20 S Serial Number 19 Serial ports 13 Slot 19 Software Version 19 Statistics Routing Frame Transmission 29 System CPU RAM (bytes) 20 T Threshold Information 11 Trademarks 2 SPECTRUM Enterprise Manager Page34 Cisco 6400 DSL

35 Index Troubleshooting 8 Type 19 SPECTRUM Enterprise Manager Page35 Cisco 6400 DSL