SPECTRUM Enterprise Manager. Device Management. Titlepae. Juniper. Supports Management Module SM-JPR1000

Transcription

1 SPECTRUM Enterprise Manager Device Management Titlepae Juniper Supports Management Module SM-JPR1000

2 Notice Aprisma Management Technologies, Inc. (Aprisma), reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Aprisma to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Copyright April 2001 by Aprisma Management Technologies. All rights reserved. Printed in the United States of America. Order Number: Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH SPECTRUM, thespectrum IMT/VNM logo, DCM, IMT, and VNM are registered trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, and Virtual Network Machine are trademarks of Aprisma or its affiliates. Juniper Networks is a registered trademark. Ethernet is a trademark of Xerox Corporation. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the Licensed Software is virus-free. Aprisma has tested its software with current virus checking technologies. However, because no anti-virus system is 100% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence. Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS Aprisma Management Technologies, Inc., 121 Technology Drive NH (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b) of this Notice or as otherwise expressly stated in the contract. (b) This computer software may be: (1) Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred; (2) Used or copied for use in a backup computer if any computer for which it was acquired is inoperative; (3) Reproduced for archival or backup purposes; (4) Modified, adapted, or combined with other computer software, provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights; (5) Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and (6) Used or copied for use in or transferred to a replacement computer. (c) Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosure prohibitions, with the minimum rights set forth in paragraph (b) of this clause. (d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract. (e) This Notice shall be marked on any reproduction of this computer software, in whole or in part. SPECTRUM Enterprise Manager Page2 Juniper

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 TASKS 7 DEVICE VIEWS 8 Interface Device View...8 Interface Icons...9 Interface Icon Subviews Menu...10 Interface Status View...11 Secondary Address Panel...11 MPLS Path Table...17 PERFORMANCE VIEWS 19 Device Performance View...20 Port Performance View CONFIGURATION VIEWS 21 Device Configuration View Interface Configuration View MODEL INFORMATION VIEW 23 INDEX 24 DEVICE TOPOLOGY VIEWS 12 Interface Device Topology View...12 APPLICATION VIEWS 13 Application Icons...14 MPLS Application...15 MPLS Configuration View...15 Administration Group Section...16 MPLS LSP Table...16 MPLS LSP Path Table...16 SPECTRUM Enterprise Manager Page3 Juniper

4 Introduction This section introduces the SPECTRUM Device Management documentation for the M5, M10, M20, M40, and M160 Internet Backbone Routers manufactured by Juniper Networks R. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5). Purpose and Scope Use this document as a guide for managing the Juniper devices described on Page 5 with SPECTRUM management module SM-JPR1000. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Juniper Networks devices through software models in your SPECTRUM database. Information specific to SM-JPR1000 is what is primarily included under this documentation topic. For general information about device management using SPECTRUM and explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons Management Module Software Release Notice SPECTRUM Enterprise Manager Page4 Juniper

5 Introduction Supported Devices SPECTRUM management module SM-JPR1000 currently lets you model the Juniper M5, M10, M20, M40, and M160 Internet Backbone Routers. These are high performance routers that support a variety of Internet applications such as high speed access, public and private peering, site hosting, and backbone core networking. All of the routers run the same JUNOS internet software, Internet Processor ASIC technology, and Multiprotocol Label Switching for traffic control. The routers have the characteristics listed in Table 1. The ASIC Forwarding Rate is 40 Mpps for all routers except the M160, which is 160 Mpps (aggregate). Table 1: Router Characteristics The SPECTRUM Model Supported Devices The model type for the Juniper devices is JNPR_Mxxx. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Device Icons Model Number Throughput, Gbps Number PIC Slots Model Name Small Device icon appears in Topology and Application views M5 5 4 M M M M JNPR_Mxxx Large Device icon appears in Device Topology, Location, and Interface Device views. Model Name JNPR_Mxxx SPECTRUM Enterprise Manager Page5 Juniper

6 Introduction The device-specific Icon Subviews menu options available from the Device icon are as listed below. Option Accesses the... Device Interface Device View (Page 8) DevTop Device Topology Views (Page 12) Application Application Views (Page 13) Configuration Configuration Views (Page 21) Statistics Environment Model Information Primary Application Device Statistical view, which provides the running state and % utilization statistics for such device components as the power supplies, fans, midplane, SSB, FPC and routing engine. Environmental view, which provides the running state and temperature for such device components as the power supplies, fans, midplane, SSB, FPC and routing engine. Model Information View (Page 23) Menu options that let you select Routing or MIB-II as the primary application. The SPECTRUM Model The rest of this document covering the Juniper management module is organized as follows. Tasks (Page 7) Device Views (Page 8) Device Topology Views (Page 12) Application Views (Page 13) Performance Views (Page 19) Configuration Views (Page 21) Model Information View (Page 23) SPECTRUM Enterprise Manager Page6 Juniper

7 Tasks This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information View (Page 23) Alarm Thresholds (set) Interface Icon Subviews Menu (Page 10) Configuration Information (check) Configuration Views (Page 21) IP Address (find/change) Interface Device View (Page 8) Secondary Address Panel (Page 11) LSP Transmission Info (check) MPLS LSP Table (Page 16) MPLS LSP Path Table (Page 16) MPLS Path Table (Page 17) Network Type (check) Network Type Label (Page 10) Performance (check) Interface Device View (Page 8) Interface Icons (Page 9) Performance Views (Page 19) Port Status (check/change) Interface Status View (Page 11) Topology (check) Device Topology Views (Page 12) MPLS/LSP Configuration (check) MPLS Configuration View (Page 15) SPECTRUM Enterprise Manager Page7 Juniper

8 Device Views This section describes the Device views and subviews available for models of Juniper devices in SPECTRUM. Device views use icons and labels to represent the device and its components, such as modules, ports, and applications. The only type of Device view for models of Juniper devices is the Interface Device view, which is described below InterfaceDeviceView Access: From the Icon Subviews menu for the Device icon, select Device > Interface. This view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view, as shown in Figure 2. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 2: Device View SpectroGRAPH: Router Device: Model Name File View Tools Bookmarks Help Model Name Contact Description Location Model Name JNPR_Mxxx 1 ON Ethernet ei0 0:0:1D:F:FD:B6 5 ON SFTWARLPBK lo0 0:0:1D:F:FD:B6 9 ON ATM8023 zn1 0:0:1D:F:FD:B6 512 ON AAL5 UAAL5 2 ON ATM CPU 6 ON ATM port CPU.1 10 ON ATM 7A1 ON ATM 7B1 Network Address Find Phy Addr Interface Description Device Icon 3 ON 4 ATM 7B2 7 ON ATM 7B3 11 ON ATM 8B1 ON ATM 8B2 System Up Time Manufacturer Device Type Serial Number Interface Options Panel ATM 8B3 ON 8 ON ATM 8B4 Interface Icons Model Name of type JNPR_Mxxx of Landscape node: Primary SPECTRUM Enterprise Manager Page8 Juniper

9 Device Views Interface Device View Interface Icons Figure 3 shows a close-up of an Interface icon from the Interface Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 3: a b c d e f g a 1 Interface Icon b Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label Gauge Label f g Interface Number Label This label displays the interface (port) number. IF Status Label This label displays the current status of the interface for the primary application selected, e.g., Routing or MIB-II. Table 2 lists the possible label color representations. Note that the color of the label also depends on the interface s current Administrative Status, which you set in the Interface Status View (Page 11). This view can be accessed by double-clicking the label. 1 ON Table 2: Interface Status Label Colors ethernet c fxp0 d Operational Administrative Label Color 0:0:1D:F:FD:B6 e Status Status Text Green Up ÿþ ÿ Blue Down ÿ ÿ Yellow Down ÿþ ÿ Red Testing Interface Type Label This label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Configuration View (Page 22). SPECTRUM Enterprise Manager Page9 Juniper

10 Device Views Interface Device View Network Type Label This label identifies the type of network the interface is connected to. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 11), which lets you change the address and mask for the interface. Gauge Label This label displays whichever performance statistic has been selected in the Gauge Control panel for this device s interfaces. (See the SPECTRUM Views documentation for more information.) Double-click this label to open the Port Performance View (Page 20). Interface Icon Subviews Menu Table 3 lists the device-specific Icon Subviews menu options and the views to which they provide access. Detail Table 3: Option Interface Icon Subviews Menu Accesses the... Interface Detail view, which displays packet, error, and discard breakdown pie charts for the interface. IF Status Interface Status View (Page 11). IF Configuration Interface Configuration View (Page 22). IP IF Address Translation Table Secondary Address Panel Thresholds Model Information Interface Address Translation Table view, which identifies the physical and network address for the interface. Secondary Address Panel (Page 11). Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface. Model Information View (Page 23). SPECTRUM Enterprise Manager Page10 Juniper

11 Device Views Interface Device View Interface Status View Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Status. This view provides information on the operational status of the interface and allows you to enable or disable the port. Operational Status The current state of the interface (Up, Down, Unknown, Dormant, Not Present, Lower Layer Down, or Testing). Administrative Status This button allows you to select the desired administrative state of the interface (On, Off, or Testing). Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. SPECTRUM Enterprise Manager Page11 Juniper

12 Device Topology Views This section provides a brief description of the Device Topology view available for models of the Juniper devices. These views show the connections between a modeled device and other network entities. The Interface Device Topology view is the only Device Topology view available for the Juniper models. Interface Device Topology View Access: From the Icon Subviews menu for the Device icon, select DevTop. Figure 4 illustrates this view. The lower panel uses Interface icons to represent the device s serial/network I/O ports. These Interface icons provide the same information and menu options as those in the Interface Device View (Page 8). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for further details on Device Topology views. Figure 4: Device Topology View SpectroGRAPH: Device Topology: Model Name * File View Tools Bookmarks Help Graphic of Juniper Device 1 ON 2 ON 3 ON Ethernet ei0 0:0:1D:F:FD:B6 ATM A2 0:0:1D:F:FD:B6 ATM CPU 0:0:1D:F:FD:B6 Model Name of type JNPR_Mxxx of Landscape node: Primary Model Name JNPR_Mxxx SPECTRUM Enterprise Manager Page12 Juniper

13 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Juniper devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 5: Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Net Addr Contact Description Location Prime-App Model Name JNPR_Mxxx 6E132_25 Sys Up Time Manufacturer Device Type Serial Number Model Name of type JNPR_Mxxx of Landscape node: Primary SPECTRUM Enterprise Manager Page13 Juniper

14 Application Views Application Icons The following applications are not described in this document but in other SPECTRUM documents, as listed. GenRtrApp is described in the Routing Applications document. SNMP2_Agent Application is described in the MIB-II Applications document. RMON Application is described in the RMON/RMON2 document. ATM Client Application, DS3 Application, and Frame Relay Application are described in the Miscellaneous Applications document. The following application is described in this document: MPLS Application (Page 15). Application Icons When the main Application view is in the Icon mode, each application model is represented by an icon (Figure 6). Double-clicking the Model Name label opens the associated Model Information view see Model Information View (Page 23). For some applications, the Model Type label is also a double-click zone, which opens an application-specific view. Any views accessible through these double-click zones are also accessible from the Application icon s Icon Subviews menu. Figure 6: a Application Icon ÿmib II App Note: Some views contain color-coded pie charts that display statistics. Also, some views contain Sort, Find, and Update buttons that let you update values in a view and find information. Refer to SPECTRUM Views for more information on these subjects. b c a b SNMP2_Agent SNMP2_Agent Model Name Label Condition Status Label c Model Type Label SPECTRUM Enterprise Manager Page14 Juniper

15 Application Views MPLS Application MPLS Application This application provides access to the following views and tables that provide Multiprotocol Layer Switching (MPLS) information: MPLS Configuration View (Page 15) MPLS LSP Table (Page 16) MPLS LSP Path Table (Page 16) MPLS Path Table (Page 17) MPLS has emerged from the IETF s effort to standardize a number of proprietary multilayer switching solutions for the Internet. It provides an alternative to ATM for multiplexing multiple services over individual circuits. MPLS uses a control driven model to initiate the assignment and distribution of label bindings for the establishment of Label Switched Paths (LSPs). With LSPs, traffic flows in one direction from the head end toward the tail end. Duplex traffic requires two LSPs, one to carry traffic in each direction. An LSP is created by concatenating one or more label switched hops, allowing a packet to be forwarded from one Label Switching Router (LSR) to another across the MPLS domain. An LSR supports MPLS based forwarding. MPLS uses its own standards-based IP signaling and label distribution protocols and does not implement any ATM Forum protocols. SPECTRUM implements a Juniper-based MPLS MIB. MPLS Configuration View Access: From the Icon Subviews menu for the MPLS Application icon, select Configuration. This view provides the following MPLS configuration information. MPLS Version The MPLS version number. Signaling Protocol The MPLS signaling protocol. The possible values are none, other, rsvp, and ldp. Configured LSPs The number of configured LSPs. Active LSPs The number of active LSPs. Traffic Engineering Protocol The protocol used to distribute traffic engineering and topology information to each LSR for the purpose of path computation. The possible values are none, isis, ospf, and isis-ospf. SPECTRUM Enterprise Manager Page15 Juniper

16 Application Views MPLS Application Administration Group Section This section of the MPLS Configuration view provides the administration group number and group name, which are used to label links in the traffic engineering topology in order to place constraints (include and exclude) on LSP paths. The group number can be 0 through 31. MPLS LSP Table Access: From the Icon Subviews menu for the MPLS Application icon, select LSP Table. This table contains the following fields, which provide information about LSPs. Name The name of the LSP. State The operational state of the LSP. The possible values are unknown, up, and down. Forwarded Octets The number of octets forwarded over the LSP. Forwarded Packets The number of packets forwarded over the LSP. Age The age (i.e., time since its creation) of the LSP, in 10-millisecond periods. Up Time The total time in 10-millisecond periods that this LSP has been operational. The percentage up time can be determined by from Up Time/Age * 100. Transitions The number of state transitions (up > down and down > up) that the LSP has undergone. Last Transition The time, in 10-millisecond units, since the last transition occurred on the LSP. MPLS LSP Path Table Access: From the Icon Subviews menu for the MPLS Application icon, select LSP Path Table. This table contains the following fields. Name The name of the LSP. State The operational state of the LSP. The possible values are unknown, up, and down. Source IP The source IP address of the LSP. Destination IP The destination address of the LSP. SPECTRUM Enterprise Manager Page16 Juniper

17 Application Views MPLS Application Path Changes The number of path changes this LSP has had. Last Change The time (in 10-millisecond units) since the last change occurred on the LSP. Configured Paths The number of paths configured for the LSP Standby Paths The number of standby paths configured for the LSP. Operational The number of operational paths for the LSP, including the path currently active as well as operational standby paths. MPLS Path Table Access: From the Icon Subviews menu for the MPLS Application icon, select Path Table. This table provides the following fields. Name The name of the active path for this LSP. If there is no active path for the LSP, this field will be blank and the other fields in the table will be meaningless. Type The type of path that is active. The possible values are primary, secondary, standby, and other. Explicit Route The explicit route used to set up this LSP, which may be a route configured by the user or a route automatically computed to satisfy constraints set by the user. Record Route The route actually used for this path, as recorded by the signaling protocol. Bandwidth The configured bandwidth for this LSP, in Kbps. Service Class The configured Class Of Service on this path. If the value is between 0 and 7, inclusive, this value will be inserted in the 3-bit COS field in the label. If the value is 255, the value in the COS field of the label will depend on other factors. Include A configured set of colors (administrative groups) specified as a bit vector (i.e., bit n is 1 if color n is in the set, where n = 0 is the LSB). For each link that this path goes through, the link must have colors associated with it, and the intersection of SPECTRUM Enterprise Manager Page17 Juniper

18 Application Views MPLS Application the link s colors and the include set must be non-null. Exclude A configured set of colors (administrative groups) specified as a bit vector (i.e., bit n is 1 if color n is in the set, where n = 0 is the LSB). For each link that this path goes through, the link must have colors associated with it, and the intersection of the link s colors and the exclude set must be null. Setup Priority The setup priority configured for this path. Hold Priority The hold priority configured for this path. Properties The set of configured properties for this path, expressed as a bit map. For example, if the path is an adaptive path, the bit corresponding to bit value xxx is set. The possible values are cspf, adaptive, record-route, mergeable, preemptable, preemptive, and fast-reroute. SPECTRUM Enterprise Manager Page18 Juniper

19 Performance Views This section provides brief descriptions of the Performance views available for the Juniper devices in SPECTRUM. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 7. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 7: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Name Contact Description Location Network Address System Up Time Manufacturer Device Type Serial Number Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. 0:40:0 0:30:0 0:20:0 Value Average Peak Value Log *FrameRate % Delivered % Forwarded %Transmit % Error % Discarded 0 *Frames per second Graph Properties Scroll to Date-Time Detail For more information on Performance views, refer to the SPECTRUM Views documentation. type routing of type IP Routing of Landscape node: Primary The following paragraphs list the performance attributes displayed for each Performance view supported by this management module. SPECTRUM Enterprise Manager Page19 Juniper

20 Performance Views Device Performance View Device Performance View Access: From the Icon Subviews menu for the Device icon, select Performance. Current and historical frame transmission information is provided via the following attributes. Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded Port Performance View Access: From the Icon Subviews menu for the Device Interface icon, select Performance. Current and historical packet transmission information is provided via the following attributes. Load Packet Rate % Error % Discarded SPECTRUM Enterprise Manager Page20 Juniper

21 Configuration Views This section describes the various Configuration views available for models of the Juniper devices in SPECTRUM. Configuration views let you view and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Juniper devices: Figure 8: Device Configuration View SpectroGRAPH: Model Name File View Tools Bookmarks Device Configuration View MPLS Configuration View (Page 15) Device Configuration View (Page 21) Interface Configuration View (Page 22) ó öÿ úû óòôúõô õýü ôüóò óõúôüóò ô óý ÿø þýüûúýùÿø öüõúôüóò ý ù ô ûÿ ÿ üû úò úõô ý ý üõ ÿ ù ýüúöÿ û ý Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. This view (Figure 8) provides status and configuration information about the device as a whole as well as on a port-by-port basis. Fields and column headings within the Device Configuration view and its subviews are explained in detail in SPECTRUM Views. Interface Configuration Table Sort Find Update Index Type Physical Address Max Frame Size Operational Status Model Name of type JNPR_Mxxx of Landscape node: Primary Print SPECTRUM Enterprise Manager Page21 Juniper

22 Configuration Views Interface Configuration View Interface Configuration View Access: From the Icon Subviews menu for an Interface icon in the Device view, select IF Configuration. This view provides the following information for the selected interface: Interface Index A numerical value that uniquely identifies the interface. Operation Status The current operational state of the interface (Up, Down, Unknown, Dormant, Not Present, or Lower Layer Down). Admin. Status The desired operational state of the interface (On, Off, or Testing). Last Change The System UpTime value when the interface entered its current operational state. IP Address/Network Mask This window provides a list of the user-defined names and IP addresses for the interface. Physical Address The Ethernet (MAC) address of the interface. Bandwidth The estimated bandwidth of the interface, measured in bits per second. For interfaces that do not vary in bandwidth, or no accurate estimate can be made, a nominal bandwidth is provided. Packet Size The largest packet that can be transmitted or received by the port, displayed in octets. Queue Length The length of the outbound packet queue, in packets. SPECTRUM Enterprise Manager Page22 Juniper

23 Model Information View This section provides a brief overview of the Model Information view. This view displays administrative information about the device and its applications and lets you set thresholds and alarm severity for the device. Figure 9 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to SPECTRUM Views for a complete description of this view. Model Name Contact Description Location Figure 9: File View Tools Bookmarks Primary Address Model Information View SpectroGRAPH: Model Name Model Information View Network Address Primary Application System Up Time Manufacturer User-Defined Type Device Type Serial Number General Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String Condition Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange ValueWhenRed Communication Information DCM TimeOut DCM Retry Community Name Poll/Log Information Poll Interval Polling Status Last Successful Poll Log Ratio LOGGED POLLED SPECTRUM Enterprise Manager Page23 Juniper

24 Index A Address Interface IP 10 MPLS 16 Physical (MAC) 10 Translation 11 Admin Status 9, 22 Applications 13 B Bandwidth 22 Bandwidth, MPLS 17 C Configuration Device 21 Interface 22 MPLS 15 D DevTop Views 12 Documentation 4 E Exclude, Include 18 G Gauge Label 10 H Hardware 5 I Icons Application 14 Device 5 Interface 9 Include, Exclude 17 Interface Status 11 Type, Device 9 IP Address, MPLS 16 IP Address/Network Mask 22 L Last Change 22 LSP Path 16 LSP Table 16 M Management Tasks 7 Mask 11 Model Information 23 Types of 5 MPLS Configuration 15 MPLS Path 17 Multiprotocol Layer Switching 15 N Network I/O ports 12 Network Type 10 SPECTRUM Enterprise Manager Page24 Juniper

25 Index Index O Octets Forwarded, MPLS 16 Operation Status 22 P Packet Size 22 Packets Forwarded, MPLS 16 Path Properties, MPLS 18 Paths, MPLS 17 Performance Statistics 10, 19 Physical Address 22 Port Number, Device 9 Port Status 8 Priority, MPLS 18 Q Queue Length 22 S Serial ports 12 Service Class 17 Signaling Protocol, MPLS 15 Statistics MPLS 15 Routing Frame Transmission 20 T Threshold Information 10 Topology 12 Trademarks 2 Traffic Engineering Protocol 15 Transitions, MPLS 16 Troubleshooting 7 U Up Time 16 R Restricted Rights Notice 2 Route Information 17 SPECTRUM Enterprise Manager Page25 Juniper