Copper Mountain 200/150/OnPrem2400/ DSL. Supports Management Module SM-CPM1000. Device Management

Transcription

1 Copper Mountain 200/150/OnPrem2400/ DSL Supports Management Module SM-CPM1000 Device Management

2 Copyright Notice Document Copyright 2002-present Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III (g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no anti-virus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an anti-virus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 Copper Mountain 200/150/OnPrem2400

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 Additional (Optional) Menus:...6 TASKS 7 Application Information (examine)...7 Device (configure)...7 Device Performance (monitor)...7 Launchable Applications...7 Model Information (examine)...7 Model Redundancy (configure)...7 Port Configuration (examine/modify)...7 A Port (examine/enable/disable)...7 Traps (view/monitor)...7 DEVICE VIEWS 8 Interface Icons...9 Interface Icon Subviews Menu Options...10 Interface Status View...11 Secondary Address Panel...11 APPLICATION VIEWS 13 Main Application View Supported Applications...14 Common Applications Device-Specific Applications Ds3App1407 Application...15 PERFORMANCE VIEWS 16 CONFIGURATION VIEWS 17 Device Configuration View TRAP ALARM COUNTER VIEW 18 Trap Alarm Counter Attributes...19 TRAP EVENT LOG VIEW 20 Trap Event Table...21 COPPER VIEW/COPPER ELEMENT MANAGER 25 MODEL INFORMATION VIEW 26 INDEX 27 DEVICE TOPOLOGY VIEWS 12 Device Management Page 3 Copper Mountain 200/100/OnPrem2400

4 Introduction This section introduces the SPECTRUM Device Management documentation for Copper Mountain devices. This introduction to the Device Management documentation for Copper Mountain devices contains the following information: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this documentation as a guide for managing Copper Mountain devices with the SPECTRUM management module SM-CPM1000. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Copper Mountain devices through software models in your SPECTRUM database. Only information specific to the supported management module is included under this documentation topic. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How To Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice Device Management Page 4 Copper Mountain 200/150/OnPrem2400

5 Introduction Supported Devices The SPECTRUM management module SM- CPM1000 currently allows you to model two different types of Copper Mountain devices as described below. Copper Edge 150 This is the Standalone DSL device that contains a maximum of 48 DSL ports. Copper Edge 200 This is a fully scaleble 200 DSL device, that can bond up to 8 DSL lines. Copper Mountain OnPrem 2400DSL Router The Copper Mountain Networks OnPrem 2400 is a Digital Subscriber Line (DSL) Concentrator. The OnPrem2400 supports several services including routing. Wide Area Network access, SDL line termination, IPv4 packet forwarding, NAT, Traffic Isolation, and browserbased network management. The OnPrem2400 can support up to 24 SDSL 2.3 Mbps full-duplex links. The SPECTRUM Model Supported Devices The model types for the Copper Mountain are CprEdgeDSL_H, CprEdgeDSL_V, OnPrem2400. Modeling results in the creation of Device icons that represent the Copper Mountain devices and Application icons that represent their supported applications. The Device icons contain doubleclick zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Figure 1: Model Name CprEdge150 Small and Large Device Icons Small Device icon appears in Topology, Device Topology, Application, and Container views. Large Device icon appears in Device Topology, Location, and Interface Device views. Model Name CprEdge150 Device Management Page 5 Copper Mountain 200/150/OnPrem2400

6 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Fault Management Accesses the... Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation. Device Device Views (Page 8) DevTop Device Topology Views (Page 12) Application Application Views (Page 13) Configuration Configuration Views (Page 17) Model Information Primary Application Model Information View (Page 26) Menu options that let you select either Gen Bridge App or MIB-II as the primary application. The SPECTRUM Model The rest of this document covering management module SM-CPM1000 is organized as follows: Device Views (Page 8) Device Topology Views (Page 12) Application Views (Page 13) Performance Views (Page 16) Configuration Views (Page 17) Trap Alarm Counter View (Page 18) Trap Event Log View (Page 20) Model Information View (Page 26) Additional (Optional) Menus: Copper View/Copper Element Manager on Page 25 Device Management Page 6 Copper Mountain 200/150/OnPrem2400

7 Tasks This section lists device management tasks alphabetically and provides links to descriptions of the views and/or tables used to perform the task. Application Information (examine) Application Views (Page 13) Device (configure) Configuration Views (Page 17) Device Performance (monitor) Device Views (Page 8) Device Configuration View (Page 17) A Port (examine/enable/disable) Interface Status View (Page 11) Traps (view/monitor) Trap Alarm Counter View (Page 18) Trap Event Log View (Page 20) Launchable Applications Copper View/Copper Element Manager (Page 25) Model Information (examine) Model Information View (Page 26) Model Redundancy (configure) Device Configuration View (Page 17) Port Configuration (examine/modify) Interface Icons (Page 9) Device Management Page 7 Copper Mountain 200/150/OnPrem2400

8 Device Views This section describes the Device views and subviews available for models of Copper Mountain devices in SPECTRUM. This view (Figure 2) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 2: File View Tools Bookmarks Name Contact Description Location Model Name CperEdge_150 Interface Device View SpectroGraph: Router Device Network Address Primary Application Find Phy Addr Interface Description System Up Time Manufacturer Device Type Serial Number Help 1 ON PPTPS Ven21 0:0:30:68:6F:1B 0:0:0:0 2 ON PPTPS ethernet 0:0:30:68:6F:9B 0:0:0:0 Device Management Page 8 Copper Mountain 200/150/OnPrem2400

9 Device Views Interface Icons Figure 3 shows a close-up of an Interface icon from an Interface Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 3: a b c d e f a Interface Icon b 1 ON ethernet fxp0 0:0:1D:F:FD:B Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label c d e f Interface Icons Interface Number Label This label displays the interface number. IF Status Label This label displays the current Operational Status of the interface (see Table 1). Note that the background color of the label also depends on the interface s current Administrative Status, which is set by the user (see Interface Status View on Page 11). This view can be accessed by doubleclicking the label. Table 1: Interface Status Label Colors Color Operational Status Administrative Status Label Text Green ON ON ON Blue OFF OFF OFF Yellow OFF ON OFF Red Testing Test Test Interface Type Label This label identifies the type of interface e.g., Ethernet, FDDI, Other, etc. Double-click this label to access the Interface Configuration view. See the SPECTRUM Views documentation. Device Management Page 9 Copper Mountain 200/150/OnPrem2400

10 Device Views Network Type Label This label identifies the type of network the interface is connected to. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the Address Translation Table (AT). IP Address Label This label displays the IP address for the interface. Double-click the label to open the Secondary Address Panel (Page 11), which allows you to change the address and mask for this interface. Interface Icon Subviews Menu Options Interface Icon Subviews Menu Options Table 2 lists the Icon Subviews menu options available for the Interface icon. Detail Table 2: Option Interface Icon Subviews Menu Opens the... Interface Detail view, which displays Packet, Error, and Discard Breakdown pie charts. IF Status Interface Status View (Page 11) IF Configuration Address Translation Table Secondary Address Panel Thresholds Interface Configuration view (see SPECTRUM Views). Address Translation Table (AT) (see SPECTRUM Views). Secondary Address Panel (Page 11) Interface Threshold view, which allows you to set the on/off alarm thresholds for load, packet rate, error rate, and% discarded. Model Information Model Information View (Page 26) Device Management Page 10 Copper Mountain 200/150/OnPrem2400

11 Device Views Interface Icon Subviews Menu Options Interface Status View Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select IF Status. This view provides information on the operational status of the interface and allows you to enable or disable the port. Operational Status The current state of the interface (ON, OFF, or Testing). Administrative Status This button allows you to select the desired operational state of the interface (ON, OFF, or Testing). Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Interface Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. Device Management Page 11 Copper Mountain 200/150/OnPrem2400

12 t Device Topology Views This section provides brief descriptions of the Device Topology views available for models of Copper Mountain devices in SPECTRUM. Access: From the Icon Subviews menu for the Copper Mountain Device icon, select DevTop. The lower panel of the Interface Device Topology view (Figure 4) uses interface icons to represent the device s serial/network I/O ports. These icons provide the same information and menu options as those in the Interface Device view (Page 9). If there is a device connected to a particular interface, a device icon appears on the vertical bar above the interface icon along with an icon representing the network group that contains the device. Figure 4: Interface Device Topology View SpectroGRAPH: Router Device File View Tools Bookmarks Help m o d e m e t h e r n e m od u n d e fi n e e m d u u nm n d od d e e fi e fi n m n e ed d Model Name Model Type Model Name Model Name Model Type Model Type 1 Up 0 2 Dwn 0 3 Dwn 0 6 Dwn 0 Device Management Page 12 Copper Mountain 200/150/OnPrem2400

13 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Copper Mountain devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 5: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View documentation. SpectroGRAPH: Router Device File View Tools Bookmarks Help? Model Name Network Address System Up Time Contact Manufacturer Description Device Type Location Primary Application Serial Number IP_Adress CopEdge_V 02_Routing FrRelay JK2_MIB-II rfc 1315 SNMP2_Agent GenRtrApp rfc 1315 MP2-Agent JK2_ICMP IP Routing ICMPApp ICMP_App IP2RtrApp JK2_System System2_App System2_App JK2_UDP2 UDP2_App UDP2_App Device Management Page 13 Copper Mountain 200/150/OnPrem2400

14 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Common Applications, below Device-Specific Applications (Page 15) Common Applications For the most part, these applications represent the non proprietary MIBs supported by your device. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Note: The documents listed below (in bold font) are available for viewing at: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - Open Shortest Path First Bridging Applications - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation Transmission Applications - FDDI - Point to Point - DS1 - DS3 - RS WAN - Frame Relay - Token Ring - Ethernet - Fast Ethernet - rfc1317app - rfc1285app - rfc1315app App - SONET MIB II Applications - SNMP - IP Supported Applications Device Management Page 14 Copper Mountain 200/150/OnPrem2400

15 Application Views - ICMP - TCP - System2 - UDP Technology Applications - APPN - ATM Client - DHCP - PNNI - rfc1316app - DLSw DOCSIS Applications - DOCSISCblDvApp - DOCSISQOSApp - DOCSISBPI2App - DOCSISBPIApp - DOCSISIFApp Digital Subscriber Line Applications - ADSL Ds3App1407 Application Copper-Mountain-Trap-MIB Copper-Mountain-TC-MIB These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB fields. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. Ds3App1407 Application This application is described in the Transmission Applications documentation. Device-Specific Applications SPECTRUM imports the following device-level proprietary MIBs into its database: Copper-Mountain-TC-MIB Copper-Mountain-Networks-DSL-MIB Device Management Page 15 Copper Mountain 200/150/OnPrem2400

16 Performance Views This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation..performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 6. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 6: Device Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Model Name Contact Description Location Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. 0:40:0 0:30:0 0:20:0 Value Average Peak Value Log * Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded 0 *Frames per second Graph Properties Scroll to Date-Time Detail The following paragraphs list the performance attributes displayed for each Performance view supported by this management module. type routing of type IP Routing of Landscape node: Primary Device Management Page 16 Copper Mountain 200/150/OnPrem2400

17 Configuration Views This section describes the Configuration views available for models of the Copper Mountain devices in SPECTRUM. Configuration views allow you to see and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Copper Mountain devices: Device Configuration View (Page 17) Device Configuration View Access: From the Icon Subviews menu for the Copper Mountain Device icon, select Configuration. A typical Device Configuration view is shown in Figure 7. Generally, this view includes a few fields that display device information as well as an Interface Configuration Table that lists interface parameters, some of which can be changed (see SPECTRUM Views). Some Device Configuration views include one or more buttons that provide access to device-specific configuration information. Figure 7: File View Tools Bookmarks Model Name Contact Description Location Sort Find Update Device Configuration View SpectroGRAPH: Model Name Device Configuration View Network Address Primary Application Interface Configuration Table System Up Time Manufacturer Device Type Serial Number Index Type Physical Address Max Frame Size Operational Status Model Name of type Copper Mountain of Landscape node: Primary Print Help Device Management Page 17 Copper Mountain 200/150/OnPrem2400

18 Trap Alarm Counter View This section provides information on the various indicators of alarms and alarm types provided with this view. Access: From the Icon Subviews menu for the Copper Mountain Device icon, select Trap Count. The Trap Alarm Counter view allows you to see how many alarms have been detected and the type of alarms that have been found. This view also provides you with a Trap count total as well. The alarms rank in severity from critical, major, and minor. The trap count indicates an event of some manner has occurred and the supported traps are listed in the Trap Event Log Section. File View Model Contact Description Location Figure 8: Primary Address Tools Bookmarks Trap Alarm Counter View SpectroGRAPH: Router Device Trap Alarm Counter View IP Address Primary Application System Up Time Interface Type Interface Index Serial Number Help Trap Alarm Counter Attributes Critical Alarm Count Major Alarm Count Minor Alarm Count Trap Count Warning Device Management Page 18 Copper Mountain 200/150/OnPrem2400

19 Trap Alarm Counter View Trap Alarm Counter Attributes Trap Alarm Counter Attributes The Trap Alarm Counter Attributes provide the following information: Critical Alarm Displays the number of uncleared critical alarms. Major Displays the number of uncleared major alarms. Minor Displays the number of uncleared minor alarms. Traps Displays the number of uncleared traps. See the Trap Event Table (Page 21) for further details on supported traps. Device Management Page 19 Copper Mountain 200/150/OnPrem2400

20 Trap Event Log View This section provides details of the events and traps on the monitored device. This view displays information on events that have occurred within this device. Events are displayed in the order in which they occur on the device. Information is provided in the Trap Event Table shown in Figure 9. Details concerning the information found within this table are provided in the rest of this section. A list of all traps and events is also provided in Table 3. This view is only available for the Copper Edge 150 and 200 DSL. File View Model Contact Description Location Primary Address Print Figure 9: SpectroGRAPH: Router Device Tools Bookmarks IP Address Primary Application Trap Event Log View Trap Event Table System Up Time Interface Type Interface Index Serial Number Sequence Type Obj Class Class ID Prob Cause Severity Time Tag Text Help Device Management Page 20 Copper Mountain 200/150/OnPrem2400

21 Trap Event Log View Trap Event Table This table contains information on the events that occur on the Copper Mountain devices. This table contains the following information: Sequence The order in which the events occurred on the device. Type Displays the type of event that has occurred. Obj Class Displays the object class associated with the resource reporting the event. Class ID Displays the object class that generated the event. Table 3 defines list the traps that are associated with the field. Table 3: Number Trap Event Table Trap Definitions Definition 1 Indicates an operator tried and failed to log into the system. 2 Indicates that and successfully logged into the system. 3 Indicates that an operator has successfully logged out of the system. 4 Indicates that the maximum number of operators are currently logged into the system. No more logins will be allowed until one of them logs out. 5 Indicates that logins are allowed again. 6 Indicates that the indicated system board has established communication with System Control Module. 7 Indicates that the indicated system board has stopped communication with the System Control Module Device Management Page 21 Copper Mountain 200/150/OnPrem2400

22 Trap Event Log View Trap Event Table Table 3: Trap Definitions (Continued) Table 3: Trap Definitions (Continued) Number Definition Number Definition 8 Indicates that logins are temporarily suspended for the given operator name because of 3 successive failed login attempts 9 Indicates that logins are now allowed for this user name. 10 Indicates that the given board did not successfully boot. 11 Indicates that the given boot file was downloaded to the given board successfully. 12 Indicates an attribute was changed by an operator. The text field contains the name of the changed attribute and the new value. 13 Indicates that the Config File Read operation failed. 14 Indicates that the Config File Read operation was successful. 15 Indicates that the Config File operation failed. The text field contains a description of the error encountered. 16 Indicates the Config File Write Operation executed successfully. 17 Indicates that the Operability State of a resource has changed in the system. 18 Indicates some diagnostic event occurred. The text field contains a description of the event. 19 The reason code field indicates the reason for the restart. 20 Indicates that the system fan has failed. 21 Indicates that the fan failure has been cleared. 22 Indicates that one of the two systems power supplies has failed. Device Management Page 22 Copper Mountain 200/150/OnPrem2400

23 Trap Event Log View Trap Event Table Table 3: Trap Definitions (Continued) Table 3: Trap Definitions (Continued) Number Definition Number Definition 23 Indicates that a previous power supply failure has been cleared. 24 This trap is sent at the beginning and end of a loopback test. 25 The SNMP trap that is generated when an alarm entry crosses it rising threshold and generates and event that is configured for sending SNMP traps. 26 This trap indicates that the globally timed master of slave IDSL Line card has lost network timing. 27 Indicates that the globally IDSL Line Card has reacquired network timing. 28 Sent whenever and SCM changes role from Primary to Secondary, or from Secondary to Primary. 29 Sent whenever an SCM detects redundancy has changed from enabled/disabled to disabled/enabled. 30 Sent when an SCM comes up, detects that it should be locked as the Primary SCM, but there is another Primary which has already locked the system (i.e. Disabled Redundancy). 31 Indicates a maintenance command completed successfully or failed according to the CommandStatus field. 32 Sent at the end of an interval when an object that is configured with a Falling Threshold that has dropped below the fallingthreshold value in the cmalarmtable. 33 This trap is sent whenever a modem trains at a rate less than the configured database. Device Management Page 23 Copper Mountain 200/150/OnPrem2400

24 Trap Event Log View Trap Event Table Table 3: Trap Definitions (Continued) Table 3: Trap Definitions (Continued) Number Definition Number Definition 34 Sent whenever the modem drops training. 35 1)DSL link comes up and the EndPointID matches another DSL link outside the first links bundle. 2)DSL link comes up and the EndPointID doesn t match the current EndPoint ID in its bundle. 3)DSL link that is not IMUX capable comes up and is configured in a bundle. 36 Operational state of the port is up, but the port is configured. 37 The trap is sent whenever a CPE Plug and Play update fails for one of the following reasons: 1) The CPE rejected the cmcpeplugandplay table set command. 2) The DSL port is configured for PlugandPlay and the CPE connected to the port does not support CMCP of the CmCpePlugandPlay table. 38 This is sent whenever the Plug and Play failure is cleared. Prob Cause Displays the probable cause of the event. Severity Displays the severity assigned to this event by the system. Time Tag Displays the time the event occurred. Text Displays any additional information needed to describe the event. Device Management Page 24 Copper Mountain 200/150/OnPrem2400

25 Copper View/Copper Element Manager This section describes how to access additonal menu options for the Copper View Applications/Copper Element Manager. Optional menu features for the Copper Mountain 200/150/OnPrem2400 are available that provide further configuration and management information. (For more information see the Copper Mountain website). An additional menu pick will appear in the SpectroGRAPH for Copper View Applications and Copper Mountain's Element Manager by setting an environmental variable for both NT and Solaris Platforms. The instructions for installing additional Copper Mountain menu options are listed below. For NT users: 1 Install Copper Mountains Application Suite on the same computer as the SpectroGRAPH is installed on. 2 Shutdown the SpectroGRAPH. 3 Bring up the Control Panel. 4 Select the Environment Tab. 5 Add to System Variables: For Set Entries Display Type: COPPEREXCPATH For Value Type: COPPEREXCPATH=/<Copper Mountain Install Path>/bin 6 Click the Set Button. 7 Bring up the SpectroGRAPH. The menu should now contain the Copper Mountain Menu Picks. For Solaris users: 1 Install Copper Mountains Application Suite on the same computer as the SpectroGRAPH is installed on. 2 Shutdown the SpectroGRAPH. 3 cd to /opt/spectrum 4 As root, vi spectrum60.env 5 Add Entry: COPPEREXC=/<Copper Mountain Install Path>/bin Device Management Page 25 Copper Mountain 200/150/OnPrem2400

26 Model Information View This section provides a brief description of the Model Information views available for models of Copper Mountain devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Model Information. Model Information views provide descriptive and configuration information about SPECTRUM models of individual devices, interfaces, and applications. Figure 10 shows an example of the Model Information view for a Copper Mountain interface. Model Information views are also available for each of the Interface icons in the Interface Device and Interface Device Topology views, and for each of the Application icons in the Application view. Although these views may vary slightly depending on the particular entity being modeled, their basic layout and content are similar for most SPECTRUM management modules. Therefore these views are described in more detail in the SPECTRUM Views documentation. Model Name Contact Description Location Figure 10: Model Information View File View Tools Bookmarks Help Primary Address General Information MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String of type Landscape : Primary SpectroGRAPH: Model Information View Network Address Hardware Type Primary Application i System Up Time Manufacturer Device Type Serial Number Communication Information DCM TimeOut DCM Retry Community Name Mgmnt Protocol Poll/Log Information Poll Interval Polling Status Device Management Page 26 Copper Mountain 200/150/OnPrem2400

27 27 Index A Address Translation table 11 Administrative Status 11 Applications 13 C Colors Interface Status Label 9 Configuration views 17 D Device Configuration View 17 Devices supported by this module 5 DS/E3 Information 15 I Icon Subviews Menus for Interface icon 10 Icons Interface 9, 12 Interface icon 9 Interface Icon Subviews Menu Options 10 Interface Status View 11 Administrative Status 11 Operational Status 11 L Labels Interface IF Status Label 9 Interface Number Label 9 Interface Type Label 9 Physical Address Label 10 M Model Information View 26 N Network I/O ports 12 O Operational Status 11 R Required Reading 4 S Secondary Address Panel 11 Serial ports 12 Supported devices 5 T Trap Event Table 20 V Views Configuration 17 Interface Status 11 Performance 16 Device Management Page 27 Copper Mountain 200/100/OnPrem2400