SPECTRUM Enterprise Manager. Device Management. Titlepae MRXI-22/24. Supports Management Module SM-CSI1011

Transcription

1 SPECTRUM Enterprise Manager Device Management Titlepae MRXI-22/24 Supports Management Module SM-CSI1011

2 Notice Aprisma Management Technologies, Inc. (Aprisma), reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Aprisma to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT,EVEN IF APRISMA HAS BEEN ADVISED OF,KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Copyright February 2001 by Aprisma Management Technologies. All rights reserved. Printed in the United States of America. Order Number: Aprisma Management Technologies, Inc. 121 Technology Drive Durham NH SPECTRUM, the SPECTRUM IMT/VNM logo, DCM, IMT,and VNM are registered trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology,Device Communications Manager, and Virtual Network Machine are trademarks of Aprisma or its affiliates. Ethernet is atrademark of Xerox Corporation. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the Licensed Software is virus-free. Aprisma has tested its software with current virus checking technologies. However, because no anti-virus system is 100% reliable, we strongly caution you to write protect and then verify that the Licensed Software, prior to installing it, is virus-free with an anti-virus system in which you have confidence. Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS Aprisma Management Technologies, Inc., 121 Technology Drive NH (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government except as provided in paragraph (b)ofthisnotice orasotherwiseexpressly statedinthecontract. (b) This computer software may be: (1) Used or copied for use in or with the computer or computers for which it was acquired, including use at any Government installation to which such computer or computers may be transferred; (2) Used orcopied for use in abackup computer if any computerforwhich it was acquired is inoperative; (3) Reproduced for archival or backup purposes; (4) Modified,adapted,orcombinedwithothercomputersoftware,provided that the modified, combined, or adapted portions of the derivative software incorporating restricted computer software are made subject to the same restricted rights; (5) Disclosed to and reproduced for use by support service contractors in accordance with subparagraphs (b) (1) through (4) of this clause, provided the Government makes such disclosure or reproduction subject to these restricted rights; and (6) Used or copied for use in or transferred to areplacement computer. (c) Notwithstanding the foregoing, if this computer software is published copyrighted computer software, it is licensed to the Government, without disclosureprohibitions,withtheminimum rights setforthinparagraph(b)of this clause. (d) Any other rights or limitations regarding the use, duplication, or disclosure of this computer software are to be expressly stated in, or incorporated in, the contract. (e) ThisNoticeshallbemarkedonanyreproductionofthiscomputersoftware,in wholeorinpart. SPECTRUM Enterprise Manager Page2 MRXI 22/24

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 DEVICE VIEWS 6 Chassis Device View...6 Interface Device Icon...7 Device Identification Label...7 Device Icon Subviews Menu...8 Port Identification Label...9 Port Identification Label Subviews Menu...10 CONFIGURATION VIEWS 11 Device Configuration View...11 MRXI-22/24 Component Table View...12 Interface Configuration Table...12 Community String Information View...13 Repeater Configuration View...14 Repeater Management...14 Source Address Management...15 Trap Configuration...15 Alarm Configuration...16 Error Source...16 Board Map...17 Manages...17 Module and Port Configuration Views...17 Module Management (Module Configuration View Only) 18 Port Management (Port Configuration View Only)...18 Trap Configuration...19 Alarm Configuration...19 Error Source...20 Source Addressing Views...21 Module Source Address Table View...21 Source Address Board/Port Location View...21 Port Source Address Table View...21 PERFORMANCE VIEWS 23 APPLICATION VIEWS 24 Application Icons...25 Supported Applications...26 Download Application...26 MODEL INFORMATION VIEWS 27 INDEX 28 SPECTRUM Enterprise Manager Page3 MRXI 22/24

4 Introduction This section introduces the SPECTRUM Device Management documentation for MRXI devices. This introduction to the Device Management documentation for MRXI devices contains the following information: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this documentation as a guide for managing MRXI devices with the SPECTRUM management module SM-CSI1011. The documentation describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot MRXI devices through software models in your SPECTRUM database. Only information specific to the supported management module is included under this documentation topic. For general information about device management using SPECTRUM and for explanations of basic SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documentation topics listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons Management Module Software Release Notice SPECTRUM Enterprise Manager Page4 MRXI 22/24

5 Introduction Supported Devices The SPECTRUM management module SM- CSI1011 currently allows you to model the MRXI- 22 and MRXI-24 standalone multi-port repeating hubs. The MRXI-22 contains twelve RJ-45 connectors, the MRXI-24 contains 24 RJ-45 connectors. Both devices support additional network connections through the use of one interchangeable front panel Ethernet Port Interface Module (EPIM). A variety of EPIMs permit the expansion of an network by supporting UTP, STP, fiber optic, Thin Ethernet, and AUI network connections. The SPECTRUM Model Supported Devices SPECTRUM uses a single device model type, HubCSIMRXi, for modeling any of the supported MRXI devices. models are represented in SpectroGRAPH views by Device icons. As shows, the appearance of the Device icon varies slightly depending on the kind of view it appears in. Figure 1: Model Name Small and Large Device Icons Small Device icon appears in Topology, Device Topology, Application Views LargeDeviceicon appears in Device Topology, Location, and Interface Device views. Model Name SPECTRUM Enterprise Manager Page5 MRXI 22/24

6 Device Views This section describes the Device views and subviews available for models of MRXI devices in SPECTRUM. Device views use icons and labels to represent the modeled device and its components, such as modules, ports, and applications. There is one type of Device view for MRXI models: Chassis Device View Chassis Device View This view shows a logical representation of the device chassis and its interfaces or ports. The Chassis Device view provides menu and doubleclick zone access to the views that monitor the interfaces. Figure 2: Chassis Device View Example of type HubCSIMRXi of Landscape daedalus:primary * File View Help? Model Name Contact Description Location Network Address Primary Application Sys Up Time Manufacturer Device Type Serial Number 1 Device MRXi22 Icon 12 ON 11 ON 10 ON 9 ON 8 ON 7 ON 6 ON 5 ON 4 ON 3 ON 2 ON 1 ON 13 ON Port Label E1 SPECTRUM Enterprise Manager Page6 MRXI 22/24

7 Interface Device Icon This icon is a logical representation of the physical module and its front panel interfaces or ports. This section describes the information available from the icon. Figure 3 shows an example of a Device icon. Note: The callouts displayed in this illustration identify the label name and the view to which it provides double-click access. Device Label/ Performance View Device Number/ Device Notes Figure 3: 1 MRXi22 Device Identification Label Interface Device Icon Port Number/ Port Zones Port Port Status Label/ Identification Port Configuration View Label Port Packet Rate Label/ Port Performance View 12 ON 11 ON 10 ON 3 ON 2 ON 1 ON 13 ON E1 CloseAlt+F4 Navigate Alarms Performance Notes... Utilities Zoom Port Notes Port Configuration Port Performance CloseAlt+F4 Navigate Alarms Performance Notes... Utilities MRXI Model Information MRXI Configuration Application View Module Notes Module Device Identification Label This label provides the following information (See Figure 3): Device Number Identifies the device s location in the Stack. Double-click this area to open the Notes Facility described in the SPECTRUM Views documentation. SPECTRUM Enterprise Manager Page7 MRXI 22/24

8 Device Label Identifies the type of device. Double-click this label to open the Performance view described in the SPECTRUM Views documentation. Device Icon Subviews Menu Table 1 lists each of the device-specific Icon Subviews menu selections available for this device. Table 1: Menu Selection MRXI Model Information MRXI Configuration Application View Module Notes Module Configuration Device Icon Subviews Menu Description Opens the Model Information view described in the SPECTRUM Views documentation. Opens the Device Configuration View (Page 11) described in Configuration Views (Page 11). Opens the MRXI Application view described in the SPECTRUM Views documentation. Opens the Notes view described in the SPECTRUM Views documentation. Opens the Module Configuration view described in Configuration Views (Page 11). Table 1: Module Performance Module Frame & Error Breakdown Module Frame Size Module DevTop View Module Source Address Table Find Source Address Module Security Configuration Repeater Redundancy Enable All Ports Device Icon Subviews Menu Opens the Module Performance view described in the SPECTRUM Views documentation. Opens the Module Frame & Error Breakdown view described in the SPECTRUM Views documentation. Opens the Module Frame Size view described in the SPECTRUM Views documentation. Opens the Device Topology view described in the SPECTRUM Views documentation. Opens the Module Source Address Table View (Page 21)described in Configuration Views (Page 11). Allows you to find a Source Address on the Module Source Address Table. Opens the Repeater Security View described in the SPECTRUM Portable Management Application for the MRXI-22/24 User s Guide. Opens the Repeater Redundancy Circuit View which allows you to set up redundancy on the device. Displays the Enable All Ports view, which allows you to enable all the ports on the module. SPECTRUM Enterprise Manager Page8 MRXI 22/24

9 Device Views Port Identification Label This label provides access to the Icon Subviews menu for the individual ports. It contains the following information (see Figure 4). Note: The callouts displayed in this illustration identify the label name and the view to which it provides double-click access. Example: Device Type/Performance View displays the type of device and provides doubleclick access to the Performance View. The menus displayed in the illustration are the Icon Subviews for that label. Port Number The number of the port represented. For the MRXI-22, labels 1 through 12 refer to the port, and 13 to the EPIM. For the MRXI-24, 1 through 22 refer to the port, and 23 to the EPIM. Doubleclick this area to open the Notes view described in the SPECTRUM Views documentation. Port Status The port activity status. Table 2 lists the possible states. Double-click this label to open the Port Configuration view described in the SPECTRUM Views documentation. Table 2: Interface Status Color Status Description Figure 4: CloseAlt+F4 Navigate Alarms Performance Notes... Utilities Zoom Port Notes Port Configuration Port Performance Port Frame & Error Breakdown PortFrameSize& Port Identification Label Port Identification Label 3 ON Port Number/ Port Notes View Port Status/ Port Configuration Port Packet Rate/ Port Performance V Green ON Port is forwarding. Blue UNK The status is unknown. Blue OFF Port is off. Red SEG Segmented. Yellow NLK No Link. Port Packet Rate The number of packets transmitted. Double-click this area to open the Error Breakdown view described in the SPECTRUM Views documentation. SPECTRUM Enterprise Manager Page9 MRXI 22/24

10 Device Views Port Identification Label Subviews Menu Table 3 describes the Port Identification Label Subviews menu selections. Table 3: Menu Selection Port Notes Port Configuration Hub Stack Icon Subviews Menu Description Opens the Notes view described in the SPECTRUM Views documentation. Opens the Module and Port Configuration Views (Page 17) described in Configuration Views (Page 11). Table 3: Port Source Address Table Port Security Configuration Enable/Disable Port Hub Stack Icon Subviews Menu Opens the Port Source Address Table View (Page 21) described in Configuration Views (Page 11). Opens the Repeater Security View described in the SPECTRUM Portable Management Application for the MRXi-22/-24 User s Guide. Displays the Enable/Disable Port View which allows you to toggle the selected port between enabled and disabled states. Port Performance Port Frame & Error Breakdown Port Frame Size & Protocols Port Redundancy Opens the Port Performance view described in the SPECTRUM Views documentation. Opens the Port Frame & Error Breakdown view described in the SPECTRUM Views documentation. Opens the Port Frame Size & Protocols view described in the SPECTRUM Views documentation. Opens the Port Redundancy Circuit View which allows you to set up redundancy on the selected port. SPECTRUM Enterprise Manager Page10 MRXI 22/24

11 Configuration Views This section describes the Configuration views and subviews available to MRXI models in SPECTRUM. These views display network configuration and operating information for the device and its interfaces. The following Configuration views are available for this device: Device Configuration View Repeater Configuration View (Page 14) Module and Port Configuration Views (Page 17) Source Addressing Views (Page 21) Device Configuration View Access: From the Icon Subviews menu for the device icon, select MRXI Configuration. This view provides device-specific configuration information as well as access to other views that allow you to configure device components. This section of the MRXI Device Configuration view displays the following device-specific information: Figure 5: JK2 of Type HubCSIMRXi Landscape X Primary Device Configuration View SpectroGRAPH: ÿ ÿ ÿ i Device Configuration View ó öù ÿùø þ ú ô üù ù ýü óòôûõô õþý ôýóò òô þ ûõ ù ú òô þ ûõ ù ò óõûôýóò ÿþýüûþúùø öýõûôýóò þýûöù ü þ ÿþýüûþúùø þ óòôûõôù ôûô Redundancy and Model Reconfiguration Options Sort Find Update Device Name The user-defined device name. ü Interface Configuration Table þùó ù òô þ ûõ Interface Address Translation Index Description Type Bandwidth Physical Address Operation Status SPECTRUM Enterprise Manager Page11 MRXI 22/24

12 Contact Status Indicates whether a connection with the device has been established. Possible values are Established, Lost, or Initial. Firmware Revision The firmware version of the device. Hardware Revision The hardware version of the device. MAC Address The Ethernet (MAC) address of the device. Date The date that the current firmware was loaded. This view also provides the following buttons, which allow you to configure this device: Component Table Opens the MRXI-22/24 Component Table View described below. DownLoad Application Opens the DownLoad Application view. This view allows you to upgrade the firmware for the device from a TFTP Boot or Bootp Server. MRXI-22/24 Component Table View This view provides information on the device firmware components. Clicking in the Community String Fields allows you to change the selected component s community strings. The Component Status button allows you to enable or disable the selected component. ID The identification number for this component. Name The name of this component. Basic Community String The community password. The default value for this entry is Public. Status The administrative security status of the component. Possible states are Unknown, Invalid, Enabled, Testing, Operational, Error, Disabled, and Delete. Interface Configuration Table This section of the MRXI Device Configuration View provides the following interface configuration information: SPECTRUM Enterprise Manager Page12 MRXI 22/24

13 Number of Interfaces The current number of interfaces in this Interface Configuration Table. Description A description of the interface including the manufacturer, product name, and version number of the hardware interface. Type The type of interface. Possible interface types and a brief description of each type are shown under MRXI-22/24 Component Table View. Bandwidth The estimated bandwidth of the interface measured in bits per second. For interfaces that do not vary in bandwidth or for which no accurate estimate can be made, a nominal bandwidth is provided. Phy Address The Ethernet (MAC) address of the interface. Oper Status The current operational state of the interface (Up, Down, or Testing). Admin Status The desired operational state of the interface (Up, Down, or Testing). Change Time The SystemUpTime value when the interface entered its current operational state. Q. Length The maximum length of the outbound queue in packets. P. Size The largest Maximum Transmission Unit (MTU) that can be transmitted or received by the interface measured in octets. Community String Information View Access: Double-click on the desired entry in the Component Table. This view provides detailed information on a specific entry in the Component Table, and allows you to modify user-settable fields. ID The component identification number. Name The name of this component. SPECTRUM Enterprise Manager Page13 MRXI 22/24

14 Version The version number for this firmware component. Administrative Status Allows you to set the administrative security status of the component. Possible states are Unknown, Invalid, Enabled, Testing, Operational, Error, Disabled, and Delete. Basic Community String The basic community string for this component. The default is Public. Read Only Community String The read only community string for this component. Read Write Community String The read write community string for this component. Super User Community String The super user community string for this component. Repeater Configuration View Access: From the Icon Subviews menu for the MRXiRptr Application icon, select Configuration. This view provides information on the MRXI- 22/24 network, host, port, and model configuration. Repeater Management This area of the Repeater Configuration view provides the following port information: Port Count The total number of ports on this LAN segment. Ports On The total number of ports on this network currently in the ON state. SPECTRUM Enterprise Manager Page14 MRXI 22/24

15 Configuration Views Ports Operational The number of ports on this network currently transmitting/receiving data. Network Ports Allows you to Enable all the ports on this network segment. Network Port Security Allows you to configure the security state for the ports on this network segment. Source Address Management This area of the Repeater Configuration view provides the following source address information: Ageing Interval The timeout period, in seconds. The timeout period is how long dynamically learned forwarding information remains in the database before being selected. You can modify this value. Trap Configuration This area of the Repeater Configuration view allows you to enable or disable any of the following types of traps: Link Traps Allows you to Enable the Link Trap generation, such that all packets indicating a change in link status are reported within the trap database. Segmentation Traps Allows you to Enable the Segmentation Trap generation, such that all packets indicating a change in segmentation status are reported within the trap database. Source Address Traps Allows you to Enable the Source Address Trap generation, such that all packets indicating a change in source address are reported within the trap database. SPECTRUM Enterprise Manager Page15 MRXI 22/24

16 Configuration Views Alarm Configuration This area of the Repeater Configuration view provides the following configuration and status information for generating alarms for the device: Timebase Allows you to set the number of seconds used as the interval for performing all of the rate alarm checks. The minimum is 10 seconds. For example, if the timebase is 10 seconds, an alarm will occur only when the specified number of errors occur within 10 seconds. Traffic Alarms Allows you to configure whether traffic alarms are disabled or enabled. Traffic Threshold The threshold number of packets, within the alarm timebase, that will generate a traffic alarm. You can modify this value. Collision Alarms Allows you to configure whether collision alarms are disabled or enabled. Collision Threshold The threshold number of collisions per good packet, within the alarm timebase, that will generate a collision alarm. You can modify this value. Broadcast Alarms Allows you to configure whether broadcast alarms are disabled or enabled. Broadcast Threshold The threshold number of broadcasts received, within the alarm timebase, that will generate a broadcast alarm. You can modify this value. Error Alarms Allows you to configure whether error alarms are disabled or enabled. Error Threshold The percentage of errors per good packet, within the alarm timebase, that will generate an error alarm. Error Source This area of the Repeater Configuration view provides a series of buttons, allowing you to select SPECTRUM Enterprise Manager Page16 MRXI 22/24

17 Configuration Views Module and Port Configuration Views the types of errors to include in the error sum. The selectable error types are as follows: CRC The number of packets received with bad Cyclical Redundancy Checks (CRC). Runts The number of runt packets received. A runt packet is one byte less than the standard Ethernet frame of 64 bytes, not including preamble. OOW_Colls The number of out-of-window collisions, those outside the standard window (51.2 s), due to a network problem. Alignment The number of misaligned packets detected. No_Resource The number of times the board ran out of resources (i.e., lack of buffer space) and packets could not be accepted. Giants The amount of giant packets received. A giant packet exceeds 1518 bytes, not including preamble. Board Map This area of the Repeater Configuration view displays a series of read-only indicators displaying the slot numbers where the repeater resides in the MMAC-FNB chassis. Standalone devices, such as the MRXI-22/24, will always exist in Slot-1. Manages This area of the Repeater Configuration view displays the user-supplied or default model name of the device managing this repeater. This section also allows you to access the Device Configuration view by double-clicking the name, or highlighting the name and clicking OK. Module and Port Configuration Views Access: From the Icon Subviews menu for the device icon, select Module Configuration or Port Configuration. The Module or Port Configuration views provide information on the configuration and operating status of the MRXI-22/24 module as a whole or of selected individual ports on the module. SPECTRUM Enterprise Manager Page17 MRXI 22/24

18 Configuration Views Module Management (Module Configuration View Only) This area of the Module Configuration view provides the following port information for the selected module: Port Count The total number of ports on this module. Ports On The total number of ports on this module currently in the ON state. Ports Operational The number of ports on this module currently transmitting/receiving data. Module Ports Allows you to Enable all the ports on this module. You can also enable module ports by selecting Enable All Ports from the Icon Subviews menu. Port Management (Port Configuration View Only) This area of the Port Configuration view provides the following information for the selected port: Port ID The number of the module port. Administrative Status Allows you to configure the desired state of the port (Enable or Disable). Operational Status The current operational state of the port (Not- Operational or Operational). Segmentation Status The current segmentation state of the port (Not- Segmented or Segmented). Link Status The current link state of the port (Not-Linked, Linked, or Not-Applicable). Topological State The current port topological state (Station or Trunk). Set Topological State Allows you to configure the desired port topological state (Not_Forced or Forced_Trunk). SPECTRUM Enterprise Manager Page18 MRXI 22/24

19 Configuration Views Trap Configuration This area of the Module or Port Configuration View allows you to enable or disable any of the following types of traps: Link Traps Allows you to Enable Link Trap generation, such that all packets indicating a change in link status are reported within the trap database. Segmentation Traps Allows you to Enable Segmentation Trap generation, such that all packets indicating a change in segmentation status are reported within the trap database. Source Address Traps Allows you to Enable Source Address Trap generation, such that all packets indicating a change in source address are reported within the trap database. Alarm Configuration This area of the Module or Port Configuration view provides the following configuration and status information for generating alarms for the selected module or port: Traffic Alarms Allows you to configure whether traffic alarms are disabled or enabled. Traffic Threshold The threshold number of packets, within the alarm timebase, that will generate a traffic alarm. You can modify this value. Traffic Alarm Condition Allows you to disable the module or port if the traffic alarm conditions described above are met and an alarm for the module is generated. This is useful in preventing excessive network traffic from alarm messages transmitted by the module, and allows for module troubleshooting. Collision Alarms Allows you to configure whether collision alarms are disabled or enabled. Collision Threshold The threshold number of collisions per good packet, within the alarm timebase, that will SPECTRUM Enterprise Manager Page19 MRXI 22/24

20 Configuration Views generate a collision alarm. You can modify this value. by the module, and allows for module or port troubleshooting. Collision Alarm Condition Allows you to disable the module or port if the collision alarm conditions described above are met and an alarm for the module or port is generated. This is useful in preventing excessive network traffic from alarm messages transmitted by the module, and allows for module or port troubleshooting. Broadcast Alarms Allows you to configure whether broadcast alarms are disabled or enabled. Broadcast Threshold The threshold number of broadcasts received, within the alarm timebase, that will generate a broadcast alarm. You can modify this value. Broadcast Alarm Condition Allows you to disable the module or port if the broadcast alarm conditions described above are met, and an alarm for the module or port is generated. This is useful in preventing excessive network traffic from alarm messages transmitted Error Alarms Allows you to configure whether error alarms are disabled or enabled. Error Threshold The percentage of errors per good packet, within the alarm timebase, that will generate an error alarm. You can modify this value. Error Alarm Condition Allows you to disable the module or port if the error alarm conditions described above are met and an alarm for the module or port is generated. This is useful in preventing excessive network traffic from alarm messages transmitted by the module, and allows for module or port troubleshooting. Error Source This view is the same as that described under Error Source (Page 16) in the section on Repeater Configuration View (Page 14). SPECTRUM Enterprise Manager Page20 MRXI 22/24

21 Configuration Views Source Addressing Views Source Addressing Views Source Address Tables are used to determine which frames will be forwarded from one network segment to another. This section provides a description of the source addressing views used to establish a source address table for the MRXI- 22/24. Module Source Address Table View Access: From the Icon Subviews menu for the MRXI- 22/24 Device icon, select Module Source Address Table. This view provides the following information: Source Address The addresses of the source devices sending packets received by the MRXI-22/24 module over any port. Port ID The number identifying the port over which the module received the packet from the corresponding source address. Board ID The number identifying the MRXI-22/24 module. This value will always be 1. Source Address Board/Port Location View Access: From the Icon Subviews menu for the MRXI- 22/24 Device icon, select Find Source Address. This view provides the following information: Model Name The network name of the MRXI-22/24 being modeled. Network Address The IP address of the MRXI-22/24 being modeled. Source Address Enter the desired ethernet address here, using the File/Update feature. Board Number The module through which packets are being sent for the specified ethernet source address. Port Number The port through which packets are being sent for the specified ethernet source address. Port Source Address Table View Access: From the Icon Subviews menu for the MRXI- 22/24 Device icon, select Port Source Address Table. This table provides the following information: SPECTRUM Enterprise Manager Page21 MRXI 22/24

22 Configuration Views Name Name of the application (Repeating) being run by the port. Network Address The IP address of the MRXI-22/24 being modeled. Device Type A textual identifier for the kind of device being modeled. Slot/Port Number The number identifying the module and port this table applies to, in the format module.port. The value of the module will always be 1. Port Source Address Table The addresses of the source devices sending packets received by the MRXI-22/24 module over this port. SPECTRUM Enterprise Manager Page22 MRXI 22/24

23 Performance Views This section provides brief descriptions of the Performance views available for the MRXI devices in SPECTRUM. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 6. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. For more information on Performance views, refer to the SPECTRUM Views documentation. 0:40:0 0:30:0 0:20:0 Figure 6: Log Performance View SpectroGRAPH: ÿfile View Tools Bookmarks Helpÿ Name Contact Description Location Network Address Primary Application ÿþýüûþúùøõõþö Load Frame Rate Errors GraphProperties Value Average Peak Value Scroll todate-time Bridging of type of Landscape IP_Address:Primary System Up Time Manufacturer Device Type Serial Number Errors Frames SPECTRUM Enterprise Manager Page23 MRXI 22/24

24 Application Views This section describes the main Application view and the associated application-specific subviews available for models of MRXI devices in SPECTRUM. When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 7 shows an Application view in its default mode (Icon) where each of the application models is represented by an Application icon (see Figure 8 for a close-up). The Application icons are arranged hierarchically under a Device icon, with major applications in the top row and their respective minor applications stacked directly below. If you prefer to see applications displayed by name only, in a single vertical list, select View > Mode > List. Figure 7: Main Application View SpectroGRAPH: File View Tools Bookmarks Help Model Name Network Address System Up Time Contact Manufacturer Description Device Type Location Primary Application Serial Number JK2 02_Routing Bridge App JK2_MIB-II BWMgmtA ConfigApps MotConfigApps SNMP2_Agent BWMgmtApps BWMgmtApp GenRtrApp GenRtrApp MP2-Agent ConfigApps ce Routing JK2_CSIS JK2_ICMP JK2_DC_Ap IP Routing ICMPApp MotDCApp MotCSISApp ce_rtr_app ICMP_App MotDCApp MotCSISApp IP2RtrApp JK2_TFTP JK2 Static JK2_System MotTFTPApp System2_App MotTFTPApp Static_App System2_App JK2_UDP2 Transparen UDP2_App UDP2_App arent_app i JK2 of type HubCSIMRXi Landscape node: Primary SPECTRUM Enterprise Manager Page24 MRXI 22/24

25 Application Icons When the Application view is in Icon mode, each of the application models is represented by an Application icon (Figure 8). Double-clicking the Model Name label (a) at the top of the icon opens the associated Model Information view-see Model Information Views (Page 27). For some applications, the Model Type label (c) at the bottom of the icon is also a double-click zone, which opens an application-specific view. Any views accessible through these double-click zones are also accessible from the Application icon s Icon Subviews menu. Figure 8: Application Icon (a) ù ø ø (b) ø ø ø ø (c) a Model Name Label / Model Information View b Condition Status Label c Model Type Label / Application-Specific View SPECTRUM Enterprise Manager Page25 MRXI 22/24

26 Application Views Supported Applications The MRXI devices support both common applications (those supported by all or most devices) and device -specific applications. Table 4 lists the applications that are commonly available for many or all devices managed by SPECTRUM. Because they are common throughout device management within SPECTRUM, they are described in the documentation listed within the table. Download Application Access: From the Icon Subviews menu for the CTDownLoadApp Application, select Download Application. This application provides download functionality for this device. The Download Application view is an SPMA view. For details on use of this function, refer to SPECTRUM Portable Management Application Tools Guide. Table 4: Common Applications Supported Application Routing (GenRtrApp) Ethernet (EthernetApp) Bridging (GenBridgingApp ) MIB-II (SNMP2_Agent) For more info. see... Miscellaneous Applications Miscellaneous Applications Bridging Applications MIB-II Applications SPECTRUM Enterprise Manager Page26 MRXI 22/24

27 Model Information Views This section provides a brief description of the Model Information views available for models of MRXI devices in SPECTRUM. Model Information views provide descriptive and configuration information about SPECTRUM models of individual devices, interfaces, and applications. Figure 9 shows an example of the Model Information view accessed from the Icon Subviews menu for the model s Device icon. Model Information views are also available for each of the Interface icons in the Interface Device and Interface Device Topology views, and for each of the application icons in the Application view. Although these views may vary slightly depending on the particular entity being modeled, their basic layout and content are similar for most SPECTRUM management modules. Therefore these views are described in more detail in the SPECTRUM Views documentation. Name Contact Description Location Figure 9: Model Information View SpectroGRAPH: File View Tools Bookmarks Help General Information MM Name MMPart Number MMVersion Number Model Type Model Creation Time Model CreatedBy Model State Security String Condition Condition Value Contact Status Model Information View Network Address Primary Application i System Up Time Manufacturer Device Type Serial Number Communication Information DCM TimeOut DCM Retry Community Name Poll/Log Information Poll Interval Polling Status Last Successful Poll Log Ratio Lost Child Count Value When Yellow Value When Orange Value When Red LOGGED POLLED JK2 of type HubCSIMRXi Landscape Node: Primary SPECTRUM Enterprise Manager Page27 MRXI 22/24

28 30 Index A Accessing the Device Configuration View 11 Admin Status 13 Administrative Status 18 Ageing Interval 15 Alarm Configuration 16, 19 Alignment 17 Application Common Bridging (GenBridgingApp) 26 Ethernet (EthernetApp) 26 MIB-II (SNMP2_Agent) 26 Routing (GenRtrApp) 26 B Bandwidth 13 Basic Community String 14 Board Map 17 Board Number 21 Broadcast C Alarm 20 Condition 20 Alarms 16 Threshold 16, 20 Change Time 13 Collision Alarm 19 Condition 20 Alarms 16 Threshold 16, 19 Component Table 12 Configuration View Device 11 Repeater 11 Source Address 11 Contact Status 12 CRC 17 Cyclical Redundancy Checks 17 D Date 12 Description 13 Device Name 11 View 5 Device Configuration Information 11 Device Configuration View 11 Device Icon 7 Device Icon Subviews Menu 8 Device Identification Labels 7 Device Number 7 Device Type 8 Device Views Chassis 6 DownLoad Application 12 Downloading 26 E EPIM 5 Error Alarm 20 Condition 20 Alarms 16 Source 16, 20 Threshold 16, 20 SPECTRUM Enterprise Manager Page28 MRXI 22/24

29 Index F Firmware Revision 12 G Generic View Banner 11 Giants 17 H Hardware Revision 12 I ID 12, 13 Interface Configuration Table 12 L Link Status 18 Traps 19 Link Traps 15 M MAC Address 12 Manages 17 Model Name 21 Module Management 18 Ports 18 Source Address Table View 21 Module Configuration View 17 MRXI-22/24 Component Table View 12 N Name 12, 13 Network Port 15 Network Address 21 Network Port Security 15 No_Resource 17 Number of Interfaces 13 O OOW_Colls 17 Oper Status 13 Operational Status 18 P Index P. Size 13 Phy Address 13 Port Count 14, 18 ID 18 Management 18 Number 21 On 14, 18 Operational 15, 18 Source Address Table View 21 Port Configuration View 17 Port Number 9 Port Packet Rate 9 Port Status Label 9 Q Q. Length 13 R Reconfigure Router Addresses 14 Repeater Management 14 Repeater Configuration View 14 Restricted Rights Notice 2 RJ-45 5 Runts 17 SPECTRUM Enterprise Manager Page29 MRXI 22/24

30 Index Index S Segmentation Status 18 Traps 19 Segmentation Traps 15 Set Topological State 18 Source Address 21 Board/Port Location View 21 Source Address Management 15 Source Address Traps 15, 19 Source Addressing 21 Status 12 V Version 14 T Timebase 16 Topological State 18 Trademarks 2 Traffic Alarm 19 Condition 19 Alarms 16 Threshold 16, 19 Trap Configuration 19 Trap Configuration 15 Type 13 SPECTRUM Enterprise Manager Page30 MRXI 22/24