HygroLog HL-NT Data Logger. Instruction Manual

Transcription

1 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 1 f 48 Dcument Ty pe HygrLg HL-NT Data Lgger Instructin Manual ; Rtrnic AG IN-E-HL-NT-V2_11

2 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 2 f 48 Dcument Ty pe Table f cntents: 1. Overview General Cmpatibility with previus mdels f prbes and dcking statins General descriptin f the HygrLg HL-NT Mdels Required accessries HygrLg HL-NT inputs Pwer supply Memry card LED Indicatrs Beeper HygrLg HL-NT functins HygrClip 2 prbe functins Event tracking Operating limits (electrnics nly) Dcking statins fr the HygrLg HL-NT Mdels Installatin Dcking statin inputs Relay cntacts Pin-ut diagrams HW4 sftware Cmputer/Operating System Requirements Operating System Cmpatibility Settings and functins accessible nly with HW ERES regulatry cmpliance Getting started Stand-alne peratin Operating mdes Display and keypad Display mdes Settings and functins accessible frm the Keypad Internal functin menu (mdels with display and keypad) Operatin n a netwrk Baud rate and cmmunicatins prtcl cmpatibility requirements Ethernet lcal area netwrk RS-485 multi-drp netwrk General wiring guidelines Guidelines fr RS-485 wiring HygrClip prbe adjustment prcedure s Single Pint adjustment Multi-Pint adjustment Warnings and useful tips Cmmunicatins prtcl Firmware updates Specificatins Acce ssrie s Supprting dcuments Dcument releases ; Rtrnic AG IN-E-HL-NT-V2_11

3 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 3 f 48 Dcument Ty pe Applicability: This manual is valid fr instruments with firmware versin 2.0x (see MENU - Instrument r check using the ROTRONIC HW4 sftware, Device Manager). Examples: 2.0a, 2.0b. Changes in the last character f the versin number reflect minr changes in the internal sftware f the instrument that d nt affect the manner in which the instrument shuld be perated. 1. Overview 1.1 General HygrLg HL-NT is a series f netwrkable data lggers primarily designed fr use with the HygrClip 2 digital humidity-temperature prbes. Depending n the mdel and ptins, the HygrLg HL-NT main features are as fllws: Internal prbe input: allws installing a HC2-S humidity-temperature prbe internally t prevent unauthrized remval. This input can als be cnnected t an external prbe by means f an extensin cable. Inputs fr up t 6 additinal external prbes, including analg prbes and 4-wire passive RTD prbes. Mnitring f up t tw external cntacts (relay utput, dr, etc.). Large recrding capacity with remvable flash memry card. Up t 750,000 values can be recrded with the standard 16 MB card. Cards with a capacity f up t 1 GB are available. Display with backlight and keypad. This allws the HygrLg HL-NT t perate as a stand-alne unit after initial cnfiguratin with the HW4 sftware. Cmpliance with FDA 21 CFR Part II and GAMP regulatins regarding electrnic recrds and electrnic signatures (ERES). Cmpatible with Ethernet netwrks (TCP / IP prtcl LAN r WLAN). Dedicated RS-485 netwrk f up t 64 HygrLg HL-NT per cmmunicatin prt Simultaneus data recrding and data display either lcally r n a PC. Internal pwer fr bth the HygrLg HL-NT and prbes is prvided by a 9V battery (factry standard) r by a 9V rechargeable battery (user supplied). The HygrLg HL-NT requires a dcking statin t (a) t pwer the HygrLg HL-NT with an external AC adapter, (b) t cnfigure the HygrLg HL-NT and cmmunicate with a PC, (c) t cnnect the HygrLg HL-NT t a netwrk and (d) t munt the HygrLg HL-NT t a wall r t place the HygrLg HL-NT n the ptinal desk-tp stand. The mst basic mdel f dcking statin simply prvides a means f munting the HygrLg HL- NT t a wall and f pwering the HygrLg HL-NT with an external AC adapter. All ther mdels ffer the same functinality as the basic mdel and als prvide a cmmunicatin prt (RS232, USB r RJ45 / Ethernet) as well as additinal inputs fr prbes and external cntacts. Dcking statins with an RS232 r USB prt are used t cnnect the HygrLg HL-NT directly t a PC. Dcking statins with an RJ45 cnnectr are used t cnnect the HygrLg HL-NT t an Ethernet LAN. In bth cases, the dcking statin features an RS485 prt that can be used t cnnect up t 64 HygrLg HL-NT in a multi-drpped arrangement (dedicated RS-485 netwrk). This is useful when the PC des nt have an Ethernet netwrk interface card r when the number f available ; Rtrnic AG IN-E-HL-NT-V2_11

4 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 4 f 48 Dcument Ty pe Ethernet prts is limited. Direct cnnectin t an Ethernet LAN allws, in principle, an unlimited number f HygrLg HL-NT t be put n a netwrk mnitred by the HW4 sftware. HW4 allws any cmbinatin f RS-232, USB, Ethernet and RS-485 cnnectins. When equipped with a dcking statin, the HygrLg HL-NT can be used tgether with the ROTRONIC HW4 sftware fr Windws based PCs (versin r higher). In additin t prviding fr the netwrking f large quantities f data lggers and ther instruments, the main functins f HW4 include: Cnfiguratin f the HygrLg HL-NT and dcking statin Prgramming f the HygrLg HL-NT lgging functin Manual r autmatic dwnlading f the data recrded by the HygrLg HL-NT On-line data mnitring and direct data recrding by the PC Autmatic generatin f graphs and data tables Mnitring f the netwrked instruments and data fr alarm cnditins Alarm reprting Maintenance f audit trails Calibratin and adjustment f the HygrClip 2 prbes Generatin f prtcls, electrnic signatures, etc. A high level f prtectin against netwrk failures can be achieved by lgging data directly n the PC while als recrding the data lcally n the HygrLg HL-NT with autmatic dwnlad t the PC at regular interval f times. Nte: Instructins fr using the HW4 sftware are nt included in this manual. These instructins are shipped separately n the sftware CD ROM. 1.2 Cmpatibility with previus mdels f prbes and dcking statins The HygrLg HL-NT is designed fr use with the HygrClip 2 prbes (UART interface) and is nt cmpatible with the previus generatin f HygrClip prbes (DIO interface). Dcking statins designed fr the previus generatin f HygrClip prbes (such as DS- U1, DS-U4, etc.) are nt cmpatible with the HygrLg HL-NT. RS-485 drp-dwn netwrks: the HygrLg HL-NT is cmpatible with previus versins f the HygrLg NT and with ther legacy prducts. The HygrLg HL-NT cannt be used in the same RS-485 drp-dwn as a HF4 r HF5 transmitters r any prduct that rely n the RO-ASCII cmmunicatins prtcl. Unlike previus versins, The HygrLg HL-NT des nt have a remte mde ; Rtrnic AG IN-E-HL-NT-V2_11

5 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 5 f 48 Dcument Ty pe 2. General descriptin f the HygrLg HL-NT 2.1 Mdels Basic mdels withut display and keypad HygrLg HL-NT2: lgger fr plug-in HygrClip 2 prbe (prbe is nt included and must be rdered separately). Prbe mdel HC2-S can be munted either internally r in the extended psitin. Other prbe mdels are external and require an extensin cable. HygrLg HL-NT3: same as HL-NT2 with 2 additinal cnnectrs suitable fr a HygrClip 2 digital prbe. Mdels with display and keypad HygrLg HL-NT2-D: same prbe as HygrLg HL-NT2 HygrLg HL-NT3-D: same prbe / prbe inputs as HygrLg HL-NT3 Mdels with internal HC2-S prbe pre-installed Mdels HL-NT2-P, HL-NT2-DP, HL-NT3-P and HL-NT3-DP are supplied with an internal HC2-S prbe pre-installed. 2.2 Required accessries Mdels withut display/keypad: The fllwing accessries are required in rder t be able t use the lgger: - Any mdel f dcking statin (except mdel DS-NT1) - Cnnecting cable dcking statin t PC - PC with the ROTRONIC HW4 sftware installed (versin r higher) Mdels with display/keypad: In principle, these mdels can be used withut any accessry. Hwever, accessing all f the prduct functins and changing sme imprtant settings such as the date and time requires the same accessries as fr the mdels withut display. 2.3 HygrLg HL-NT inputs Prbe input 1 HygrLg HL-NT2-P, HL-NT2-DP, HL-NT3-P and HL-NT3-DP: these mdels are supplied with an internal HC2-S plug-in prbe. This prbe can be either retracted r extended. The prbe can als be separated frm the lgger with an extensin cable, and in this case the HC2-S prbe may be replaced with anther mdel f HygrClip 2 prbe s as t meet specific applicatin ; Rtrnic AG IN-E-HL-NT-V2_11

6 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 6 f 48 Dcument Ty pe requirements (see dcument E-M-HC2 Prbe s-v1). Open the husing f the HygrLg t change the psitin f the prbe r t install a prbe extensin cable. T pen the husing f the HygrLg, remve the five screws, as indicated by the arrws. The far right drawing shws the HygrClip S prbe in the retracted psitin. The base f the prbe is plugged int a cnnectr that is separated frm the main bard by a length f wire. Prbe cnnectr The shrter screw ges here T extend the prbe, lift the HygrClip S prbe frm its psitin and remve the sltted cap frm the HygrLg. T extend the prbe, place n the prbe the ring supplied with the HygrLg. Insert the ring int the slt in the instrument husing where the sltted cap was. Relcate the prbe cnnectr up by ne r tw ribs. Clse the instrument husing. Prceed in a similar manner t install a prbe extensin cable. HygrClip S extended psitin Ring (replaces the sltted cap) Extensin cable used t separate the prbe frm the HygrLg ; Rtrnic AG IN-E-HL-NT-V2_11

7 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 7 f 48 Dcument Ty pe Ntes: Fr maximum prtectin against vandalism, use the HC2-S prbe in the retracted psitin. Fr a faster respnse, use the prbe in the extended psitin. Fr additinal infrmatin n the HygrClip 2 prbes see dcument E-M-HC2 Prbe s-v Prbe inputs 2 and 3 (HygrLg HL-NT3) The HygrLg HL-NT3 can be used with up t 2 additinal HygrClip 2 prbes. Fr further infrmatin n the HygrClip 2 prbes, see dcument E-M-HC2 Prbe s-v Cnnectr identificatin HL-NT2 Input 1 (HygrClip 2 prbe) HL-NT3 Input 1 (HygrClip 2 prbe) Input 2 (HygrClip 2 prbe) Input 3 (HygrClip 2 prbe) ; Rtrnic AG IN-E-HL-NT-V2_11

8 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 8 f 48 Dcument Ty pe 2.4 Pwer supply The HygrLg HL-NT ships with a regular 9V battery which must be inserted first (see battery replacement). T cnserve battery pwer, mdels with the LC display and keypad are shipped with the Display Sleep functin enabled (see Sftware Functins). When the keypad has nt been used fr sme time, this functin autmatically turns ff the display ff. The display can be temprarily activated by pressing n any key f the keypad. When cnnected t a dcking statin, the HygrLg HL-NT can be pwered with an external AC adapter. Nte: mst mdels f dcking statin require the use f an external AC adapter due t the current cnsumptin f the dcking statin internal electrnics. After recnfiguring the HygrLg HL-NT with the ROTRONIC HW4.sftware, a rechargeable battery (accumulatr) can be used instead f a regular battery. Recharging the battery require a dcking statin and an external AC adapter. WARNING: Trying t recharge a regular battery is ptentially dangerus. Whenever a regular battery is being used, the lgger shuld be cnfigured with the internal battery charge functin disabled Battery lifetime The battery lifetime depends n the manner in which the HygrLg HL-NT is being used. The HygrLg HL-NT has a battery lifetime f ne year when just ne HygrClip prbe is being used (standard 500 mah alkaline battery), when n dcking statin with internal electrnics is cnnected t the HygrLg HL-NT and when the lgger is cnfigured / prgrammed as fllws: Display Sleep functin enabled (mdels with display) N dcking statin with internal electrnics LED and beeper functins disabled Lg interval set t 15 minutes Additinal examples f battery lifetime (LED turned ff, Lgging active): in the fllwing table, LCD means that the LC display is permanently n (Display Sleep functin disabled). N dcking statin with internal electrnics is cnnected t the HygrLg HL-NT. Lifetime in days Rechargeable Battery 120mAh Rechargeable Battery 150mAh Regular Battery 500mAh Regular Battery 1000mAh 1 Prbe / 5s Interval Prbe / 5s Interval / LCD Prbe / 1min Interval Prbe / 1min Interval / LCD Prbe / 15min Interval Prbe / 15min Interval / LCD ; Rtrnic AG IN-E-HL-NT-V2_11

9 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 9 f 48 Dcument Ty pe Nte: the cnsumptin f the display is negligible when the Display Sleep functin is enabled. With the display always n, pwer cnsumptin is at its highest when the display refresh rate is set with HW4 t the minimum f 5 sec. Because f the requirement t keep track f the date and time, the HygrLg HL-NT des nt have a pwer n/ff switch. Every minute, bth the date and time are recrded t the internal EEPROM. Secnds are nt recrded. In the event f a relatively brief interruptin f pwer (such as when replacing the battery), time may fall behind in increments f ne minute. Remving the battery fr an extended perid f time will cause the lgger t cmpletely lse track f the date and time Battery replacement T access the battery, remve the screw shwn t the right and pen the rubber cver. The battery is lcated at the bttm f the instrument. cver Prbe i t 5 battery 2.5 Memry card The HygrLg HL-NT has a nn-vlatile 64 kb EEPROM internal memry that is used t save the lgger cnfiguratin data, the lgger events and t temprarily hld measurement data. The main memry is a plug-in flash memry card. As a standard, the HygrLg HL-NT ships with a 16 MB card. This card allws the recrding f up t 400,000 values in text file frmat (unprtected) r up t 750,000 values in binary file frmat (prtected). Memry cards with a capacity f up t 1 GB can be purchased frm third parties. Regardless f its size, the flash memry card hlds a maximum f 512 files and directries, including ne lgger-cnfiguratin and ne lgger-event file. The measurement data can be saved either t a file with extensin XLS r t a file with extensin LOG. Files with XLS extensin can be read with Ntepad r imprted int Micrsft Excel. Files with extensin LOG are encded in binary frmat s as t prevent data manipulatin and can nly be read with the ROTRONIC HW4 sftware. Bth types f files can c-exist n the memry card. The memry card can be remved frm the lgger and transferred t a card reader, a PDA, etc. The flash memry card can als be read withut being remved frm the lgger ; Rtrnic AG IN-E-HL-NT-V2_11

10 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 10 f 48 Dcument Ty pe Memry Card: T access the memry card, remve the screw shwn t the right and pull ut the rubber cver. The plug-in flash memry card is lcated n tp f the main bard. memry card cver screw 2.6 LED Indicatrs The HygrLg HL-NT is equipped with a green and red LED. The lgger can be cnfigured with HW4 t have the green side f the LED flash when lgging is active. The red side f the LED can be made t flash when there is an alarm cnditin (see nte belw) and / r when the lgger requires attentin (lw battery, flash memry card full, etc.) In the transient alarm mde, the red LED flashes fr nly as lng as the data frm a prbe crrespnds t an alarm cnditin. In the durable alarm mde, the red LED stays n even after the alarm cnditin has disappeared. When the LED is set t prvide a durable alarm, it can be reset frm the keypad r with HW Beeper The HygrLg HL-NT is equipped with an internal beeper and can be cnfigured with HW4 t make a clicking sund when any key is being pressed. The beeper can als be cnfigured t emit a 5-secnd nn-repeating sund when there is an alarm cnditin and / r when the lgger requires attentin. 2.8 HygrLg HL-NT functins Calculated parameter Using the HW4 sftware, the HygrLg HL-NT can be set t cmpute fr each HygrClip prbe ne f the fllwing psychrmetric parameters. Dew pint (Dp) Frst pint (Fp) Wet bulb temperature (Tw) Enthalpy (H) Vapr cncentratin (Dv) Specific humidity (Q) Mixing rati by weight (R) Vapr cncentratin at saturatin (Dvs) Vapr partial pressure (E) Vapr saturatin pressure (Ew) ; Rtrnic AG IN-E-HL-NT-V2_11

11 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 11 f 48 Dcument Ty pe Each individual prbe input can be assciated with a different parameter. Nte: depending n whether dew pint r frst pint was selected, bth the HygrLg HL-NT and HW4 will display either the symbl Dp r the symbl Fp fr values belw freezing. The symbl Fp indicates that the value is a frst pint as ppsed t being a dew pint. Regardless f the dew pint / frst pint selectin, the symbl Dp is always displayed fr values abve freezing. Sme f the abve parameters require barmetric pressure as an input. When an analg pressure prbe is cnnected t ne f the HygrLg HL-NT inputs, the lgger can be set t use the measurement frm this prbe. When n pressure prbe is being used, a fixed pressure value can be used. This value can be specified as part f the HygrLg HL-NT settings Data lgging Data lgging requires that a flash memry card be inserted inside the lgger. Using the HW4 sftware, lg files can be set t ne f the fllwing frmats: HW4 binary frmat [LOG]: files in this frmat are encded and can be pened nly with the ROTRONIC HW4 sftware. HW4 des nt allw any manipulatin / alteratin f the data and requires a passwrd t lg in. Shuld the file be smehw mdified, HW4 will give a warning that the file is nt an riginal. Text file frmat [XLS]: in principle, files in this frmat can be pened with any text editr and / r imprted int Micrsft Excel. The lg file frmat is a glbal setting f the flash memry card (changing this setting requires the HW4 sftware). At any given time, the card recrds data frm all inputs in either ne frmat r the ther. Files f different frmats can c-exist in the flash memry card. Binary files (prtected) use substantially less memry space than text files (unprtected). The lgging functin is independently activated fr each individual input. The HygrLg HL-NT creates a separate file fr each input that is t be recrded. Multiple inputs cannt be recrded t the same file. The HygrLg HL-NT autmatically generates each file name. A file name cnsists f 8 digits fllwed by the extensin LOG r XLS. The first 4 digits are the same as the last 4 digits f the lgger serial number, the 5 th digit is the same as the input number and the last 3 digits are a number between 000 and 999 used t differentiate lg files created fr the same input. The last number that was created is retained in the nn-vlatile EEPROM and is updated whenever a new file is created fr the input. When the number reaches 999, the next update will reset it t 000. All files are lcated in the rt directry f the flash memry card, including the lgger event file and the lgger cnfiguratin file. Regardless f the memry card capacity, the rt directry is limited t a maximum f 250 files. This means that the memry card can hld a maximum f 248 lg files, and that a card with this amunt f files is cnsidered t be full, even if all the memry has nt been used. Using HW4, the fllwing lg settings can be defined individually fr each input: Start date and time Stp date and time Lg interval (minimum 5 secnds) ; Rtrnic AG IN-E-HL-NT-V2_11

12 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 12 f 48 Dcument Ty pe Measured values and cmputed parameter, r any parameter cmbinatin User custm text (used fr the lg file header) User name, HW4-ID, HW4 Serial Number Autmatic creatin f a new file after 200,000 data pints r at the end f each day, week r mnth Nte: unlimited lgging (lp mde lgging) is nt pssible. Lgging stps autmatically when the flash memry card is full. Prir t lgging, the user may use HW4 t check the amunt f free memry, and verify that there is enugh rm available. If the flash memry card is remved when lgging is active, the HygrLg HL-NT will stp lgging until a new card is inserted. Unless the stp date and time have been reached, lgging will start again under the next available file name when a new card is inserted. Warning: remving the memry card while lgging is active may result in a crrupted lg file and in lss f data. Lgging can be started immediately fr any individual input frm the keypad f the HygrLg HL- NT. A deferred start can nly be prgrammed with the HW4 sftware. The green LED f the HygrLg HL-NT can be set t flash when the instrument is recrding data. T cnserve battery pwer, yu may want t d this nly when an external pwer surce is being used. Lgging can be immediately stpped fr any individual input directly frm the keypad. With HW4, lgging can be stpped either immediately r at a future date and time fr any individual input r fr all inputs. When lgging is ended, the HygrLg HL-NT returns t the measuring mde Trend indicatrs See als: Main perating mdes and measurement interval When the trend indicatr functin is enabled, a symbl appears n the left side f the LC display, n the line crrespnding t each measured r calculated value. An up arrw dentes a rising value and a dwn arrw dentes a decreasing value. Bth arrws dente a stable value. The trend f a parameter is evaluated by cmparing successive averages made f 6 values each. With the shrtest pssible measurement interval f 5 secnds, each average cvers a time perid f 30 secnds and the first indicatin f a trend is available after ne minute. Subsequently, the trend is evaluated and updated every 30 secnds. With a lnger measurement interval, each average is cmputed ver a lnger perid f time (always using 6 values) and the trend is als updated ver lnger intervals f time. Fr any measured r calculated parameter, the trend indicatr shws a stable cnditin when the abslute value f the difference between tw successive averages is < Alarm functin Using the HW4 sftware, bth a high and a lw alarm value can be assciated with the humidity, temperature and calculated parameter f each prbe input, A hysteresis value can als be entered fr each parameter. This value is used fr bth the lw and the high alarm cnditins ; Rtrnic AG IN-E-HL-NT-V2_11

13 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 13 f 48 Dcument Ty pe The HygrLg HL-NT has a red LED which can be set with HW4 t flash whenever the value f any parameter crrespnds t an alarm cnditin. The LED can be set t flash nly as lng as the alarm cnditin exits r it can be set t prvide a durable alarm and, in this case, it will t keep flashing until the alarm is reset. The HygrLg HL-NT can als be set with HW4 t beep fr 5 secnds when there is an alarm cnditin. The HygrLg HL-NT will beep nly nce, when the cnditin ccurs. Lg files d nt recrd the existence f an alarm cnditin. Hwever, when the cntents f a lg file are viewed as a data table with the HW4 sftware, values that crrespnd t an alarm cnditin are printed ver a red backgrund, based n the alarm settings that HW4 dwnladed frm the lgger Display-Sleep functin This functin can be enabled and cnfigured nly with the HW4 sftware. Using the Display Sleep functin can substantially extend the lifetime f the battery. When the Display Sleep functin is active, the LC display f the HygrLg HL-NT stays blank. The Display Sleep functin is effective bth in the measure and in the recrd mde. The display f the HygrLg HL-NT can be set t be always n. It can als be set t autmatically g blank after 30 secnds, 1, 5, 10 r 20 minutes when n key is being pressed r when there is n cmmunicatin with a PC. If the HygrClip NT was in the functin menu at the time the display ges blank, it autmatically exits the menu. The HygrLg suspends the Display Sleep functin whenever a key is pressed. The functin is als suspended when external pwer is available r when the lgger receives a cmmunicatin request (fr example frm a PC 1 ). When the display cmes up again, it shws by default the measurements frm the prbe that was selected last. 1 When the HygrLg HL-NT is cnnected by means f a dcking statin t a PC and HW4 is running, yu shuld use an external AC adapter t pwer bth the HygrLg HL-NT and dcking statin. HW4 can be set t use a plling interval as shrt as 5 secnds t interrgate all instruments cnnected t the PC and this culd cause the battery life time t be sharply reduced. 2.9 HygrClip 2 prbe functins Simulatr functin (validatin f the signal transmissin): If s desired, transmissin f the HC2 prbe utput signals can be validated by using the prbe simulatr functin. The HW4 sftware is required t enable and cnfigure this functin. When the functin is enabled the prbe generates digital and analg signals crrespnding t values specified by the user Sensr failure detectin and fail safe mde: The HygrClip 2 prbe autmatically detects a sensr failure such as a shrted r pen sensr. This infrmatin is passed t bth the HygrLg HL-NT and HW4 sftware. The ptinal display f the HygrLg HL-NT will shw an alarm message. The HygrClip 2 prbe can als be cnfigured with the HW4 sftware t generate a "safe r readily identifiable" fixed value fr humidity and temperature in the event f a shrted r pen sensr ; Rtrnic AG IN-E-HL-NT-V2_11

14 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 14 f 48 Dcument Ty pe Nte: the sensr diagnstics and drift cmpensatin functin f the HygrClip 2 prbe is nt available with the HygrLg HL-NT due t the fact that the prbe is pwered nly briefly during each lg r measurement interval Event tracking The HygrLg HL-NT maintains an internal event file with the extensin EVT. This functin is always enabled. Part f the prcedure t ensure cnfrmity t the FDA requirements is t use the HW4 sftware t disable the MENU key n the HygrLg HL-NT keypad. The MENU key is the nly key that can be used t make changes t the HygrLg HL-NT. When this prcedure is implemented, the events recrded by the HygrLg HL-NT are the result f an interactin with the HW4 sftware. When the MENU key is nt disabled, a limited number f events are recrded in the lgger event file. In this case n entries are made in the lgger event file header. The tw tables belw prvide a list f the events tracked by the HygrLg HL-NT. The lgger event file is split between the internal memry f the lgger (up t 170 events) and the flash memry card (practically unlimited number f events). HW4 ffers the pssibility f dwnlading, pening and printing the entire file cntents. All past lgger events are available t HW4 as lng as the flash memry card is nt remved frm the lgger. The serial number f the lgger is used as the file name. Example: EVT The lgger event file cnsists f a file header and a file bdy. The file header prvides the fllwing infrmatin: Mst recent prgramming f the lg functin: prgramming date and time, user and HW4 prduct ID Mst recent device cnfiguratin: date and time, user and HW4 prduct ID Mst recent adjustment t the PC date and time: date and time, user and HW4 prduct ID An individual recrd with date and time is entered in the event file bdy fr each individual event listed in the tw tables belw: Interactin with the HW4 sftware: Event Pwer up Watchdg verflw Writing device cnfiguratin Memry card remved Memry card full Descriptin The battery was inserted r the instrument pwered dwn and up after an internal prblem Internal instrument errr (nrmally shuld nt ccur) New r existing cnfiguratin written t lgger While recrding data, the lgger culd nt find the memry card. The data was written t the EEPROM and are nt yet lst N free memry space n the memry card ; Rtrnic AG IN-E-HL-NT-V2_11

15 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 15 f 48 Dcument Ty pe Event New memry card inserted Descriptin The memry card was replaced while data was being lgged. The data will be split between tw different memry cards. Pssibly, sme data has been lst. Humidity adjusted Humidity adjustment f the prbe cnnected t input # Temperature adjusted Temperature adjustment f the prbe cnnected t input # Lgging started Start recrding data frm input # Lgging stpped manually Lgging ended autmatically Out-f-limits value detected Data recrding f input # ended befre the prgrammed stp time Data recrding f input # ended at the prgrammed stp time An ut-f-limits value was newly detected n input # Battery almst empty Battery vltage drpped belw 6.5V Battery empty Beginning accumulatr charge Accumulatr charge ended MFG cmmand The battery is empty and the lgger has pwered itself ff (keeping pwer up culd result in errneus data r lss f data) Starting t charge the rechargeable battery Rechargeable battery full Reserved fr the factry Lst data, memry card nt ready While recrding data, the lgger culd nt find the memry card. The data culd nt be written t the EEPROM, and was lst HygrClip prbe 1 cnnected A HygrClip prbe was cnnected t input # HygrClip prbe discnnected 1 A HygrClip prbe was remved frm input # r the input can n lnger cmmunicate with the prbe External pwer cnnected The A/C adapter was cnnected and is being pwered External pwer remved r faulty The A/C adapter was discnnected, r failed, r is nt being pwered Device time changed / adjusted Device date and time prir and after adjustment (up t firmware v1.1d nly) Prir device time Device date and time prir t change (firmware v1.2a and up) New device time RS-485 address changed EEPROM erased Dcking statin discnnected 2 Device date and time after change (firmware v1.2a and up) The RS-485 address was changed Reserved fr the factry The dcking statin was discnnected r there is n lnger any cmmunicatin with it ; Rtrnic AG IN-E-HL-NT-V2_11

16 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 16 f 48 Dcument Ty pe Event Dcking statin cnnected 2 Lgger language file dwnladed Lg functin prgrammed Event file deleted Descriptin A dcking statin was cnnected and cmmunicatin was established A different internal language file was laded r the same file was laded again The lg functin has been prgrammed fr input # Reserved fr the factry 1 cnnectin / remval f analg prbes is nt recrded 2 nly when the dcking statin has internal electrnics Events triggered frm the keypad: Event Descriptin Humidity adjusted Humidity adjustment f the prbe cnnected t input # Temperature adjusted Temperature adjustment f the prbe cnnected t input # Lgging started Start recrding data frm input # Lgging stpped manually Prir device time New device time Lg functin prgrammed Data recrding f input # ended befre the prgrammed stp time Device date and time prir t change (firmware v1.2a and up) Device date and time after change (firmware v1.2a and up) The lg functin has been prgrammed fr input # 2.11 Operating limits (electrnics nly) Mdels withut display: C with the factry supplied alkaline battery C with a lithium battery r an external AC adapter Mdels with display: C with the factry supplied alkaline battery C with a lithium battery r an external AC adapter The HygrClip prbes have generally wider perating limits (see individual prbe specificatins) ; Rtrnic AG IN-E-HL-NT-V2_11

17 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 17 f 48 Dcument Ty pe 3. Dcking statins fr the HygrLg HL-NT The HygrLg HL-NT requires a dcking statin with the apprpriate interface t be able t cmmunicate with a PC with the ROTRONIC HW4 sftware installed. The cnnectr lcated n the back f the HygrLg HL-NT is meant t be used with ne f the available dcking statins (UART interface). When installed n a PC, the ROTRONIC HW4 sftware is used t cnfigure the HygrLg HL-NT, t prgram its lgging functin, t dwnlad the recrded data and t adjust the prbes cnnected t the lgger against a reference envirnment. A dcking statin is required fr any f the fllwing: Munt the HygrLg HL-NT t a wall Place the HygrLg n the ptinal desk-tp stand Use an external AC adapter t pwer the HygrLg HL-NT Cnnect the HygrLg HL-NT t a PC: RS232 r USB prt, Ethernet (TCP/IP) LAN r WLAN Cnnect up t 64 HygrLg HL-NT r ther devices tgether in a multi-drpped netwrk (RS-485) Depending n the mdel, using a dcking statin als adds functinality t the HygrLg HL-NT: Up t 4 additinal prbes, including analg prbes and direct 4-wire RTDs Lgical inputs (external cntacts) Relay utputs Nte: dcking statins with internal electrnics and PC interface shuld be generally used with an external AC adapter. 3.1 Mdels All mdels f dcking statin have the same physical dimensins and can be used either as a mechanical adapter t place the HygrLg HL-NT n the ptinal desk-tp stand r as a bracket t munt the HygrLg HL-NT t a wall. Dcking statins are available in the fllwing cnfiguratins: Basic dcking statins (n digital interface) HL-DS-NT0: basic dcking statin withut internal electrnics. This mdel simply prvides a means f munting the HygrLg HL-NT t a wall HL-DS-NT1: basic dcking statin withut internal electrnics (similar t mdel HL-DS- NT0). This mdel simply prvides a receptacle fr an AC adapter used t pwer the HygrLg HL-NT Dcking statins with RS-232 serial interface HL-DS-NT2: receptacle fr AC adapter, ne serial prt (RS232) and ne RS485 prt (multi-drp) ; Rtrnic AG IN-E-HL-NT-V2_11

18 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 18 f 48 Dcument Ty pe HL-DS-U1: receptacle fr AC adapter, ne serial (RS232) prt, ne RS485 prt (multidrp), fur prbe inputs (HygrClip 2 r analg prbe with vltage utput signal), ne cnnectr fr up t tw lgical input signals Dcking statins with USB interface HL-DS-NT3: receptacle fr AC adapter, ne USB prt and ne RS485 prt (multi-drp). HL-DS-U2: receptacle fr AC adapter, ne USB prt, ne RS485 prt (multi-drp), fur prbe inputs (HygrClip r analg prbe with vltage utput signal), ne cnnectr fr up t tw lgical input signals. HL-DS-U2-420: same as HL-DS-U2 but designed fr analg prbes with a 4-20 ma utput signal. Each prbe input uses an internal 150 Ohm resistr t cnvert 4 20 ma t mv (nminal). HL-DS-PT2: receptacle fr AC adapter, ne USB prt, ne RS485 prt (multi-drp netwrking), fur cnnectrs fr RTD prbe (direct 4-wire cnnectin), ne cnnectr fr up t tw lgical input signals. HL-DS-R1: receptacle fr AC adapter, ne USB prt, ne RS485 prt (multi-drp netwrking), ne cnnectr fr up t tw lgical input signals and tw independent relay utput cnnectrs Dcking statins with wired Ethernet interface Nte: with any f the fllwing mdels, use an extensin cable t separate all prbes frm either the HygrLg HL-NT r dcking statin s as t avid measurement errrs due t self-heating by the dcking statin. HL-DS-NT4: receptacle fr AC adapter, ne RJ45 cnnectr (Ethernet), ne RS485 prt (multi-drp) and ne cnnectr fr up t tw lgical input signals. HL-DS-NT4-WEB: same as HL-DS-NT4 but with an internal web server that can be accessed with a web brwser. HL-DS-U4: receptacle fr AC adapter, ne RJ45 cnnectr (Ethernet), ne RS485 prt (multi-drp), fur prbe inputs (HygrClip r analg prbe with vltage utput signal), ne cnnectr fr up t tw lgical input signals. HL-DS-U4-WEB: same as HL-DS-U4 but with an internal web server that can be accessed with a web brwser. HL-DS-U4-420: same as HL-DS-U4 but designed fr analg prbes with a 4-20 ma utput signal. Each prbe input uses an internal 150 Ohm resistr t cnvert 4 20 ma t mv (nminal). HL-DS-U4-420-WEB: same as HL-DS-U4-420 but with an internal web server that can be accessed with a web brwser ; Rtrnic AG IN-E-HL-NT-V2_11

19 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 19 f 48 Dcument Ty pe HL-DS-PT4: receptacle fr AC adapter, ne RJ45 cnnectr (Ethernet), ne RS485 prt (multi-drp netwrking), tw cnnectrs fr RTD prbe (direct 4-wire cnnectin), ne cnnectr fr up t tw lgical input signals Dcking statins with wireless Ethernet interface Nte: with any f the fllwing mdels, use an extensin cable t separate all prbes frm either the HygrLg HL-NT r dcking statin s as t avid measurement errrs due t self-heating by the dcking statin. HL-DS-NT4-WL: receptacle fr AC adapt er, WLAN transceiver, ne RS485 prt (multidrp) and ne cnnectr fr up t tw lgical input signals. HL-DS-U4-WL: receptacle fr AC adapter, WLAN transceiver, ne RS485 prt (multidrp), tw prbe inputs (HygrClip 2 r analg prbe with vltage utput signal), ne cnnectr fr up t tw lgical input signals. HL-DS-U4-WEB-WL: same as HL-DS-U4-W L but with an internal web server that can be accessed with a web brwser. HL-DS-PT4-WL: receptacle fr AC adapter, WLAN transceiver, ne RS485 prt (multidrp netwrking), tw cnnectrs fr RTD prbe (direct 4-wire cnnectin), ne cnnectr fr up t tw lgical input signals. Netwrk Interface Wireless LAN Standard IEEE b Frequency 2.4 GHz Data Rate Up t 11 Mbps with autmatic fallback Mdulatin CCK (11/5.5 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps) Typical Transmit Pwer 16 dbm Receive Sensitivity Mbps Cnnectr 1 x RP-5MA WLAN Security WEP (Wired Equivalent Privacy) 64 / 128-bit encryptin (RCA) WPA / WPA2 / i 128-bit TKIP/CCMP A (AES) encryptin Enterprise mde (802.1X); LEAP (WEP nly), PEAP, TTLS, TLS; EAP-FAST, GTC, MD5, OTP, PAP, CHAP, MSCHAP, MSCHAP V2, TTLS -MSCHAP V2 Pre-shared key mde (PSK/Persnal) Nte: The WLAN security f dcking statin HL-DS-U4-WEB-WL (with internal web brwser) is limited t WEP with 64-bit encryptin (n WPA) ; Rtrnic AG IN-E-HL-NT-V2_11

20 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 20 f 48 Dcument Ty pe 3.2 Installatin Installatin is the same fr all mdels f dcking statin. T munt the dcking statin t a wall, use the tw hles shwn n the right. The HygrLg NT can then be attached t the dcking statin as explained belw. T attach the HygrLg NT t the dcking statin: [A] Place the HygrLg NT n the dcking statin s as t match the tw areas [A]. Press lightly ne against the ther and secure the assembly with threaded pin [B]. When the dcking statin is munted n a wall, a small padlck (nt shwn) may be put thrugh pin [B] t prevent remval f the HygrLg NT frm the dcking statin. [B] [B] ; Rtrnic AG IN-E-HL-NT-V2_11

21 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 21 f 48 Dcument Ty pe Cnnectr identificatin HL-DS-U1 Prbe input 6 Prbe input 4 Prbe input 7 Prbe input 5 RS-485 Lgical inputs 12VDC Pwer (+) center RS-232 HL-DS-U2 Prbe input 6 Prbe input 4 Prbe input 7 Prbe input 5 RS-485 Lgical inputs 12VDC Pwer (+) center USB ; Rtrnic AG IN-E-HL-NT-V2_11

22 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 22 f 48 Dcument Ty pe HL-DS-U4 / HL-DS-U4-420 Prbe input 6 Prbe input 4 RJ45 Prbe input 5 RS-485 Lgical inputs 12VDC Pwer (+) center Prbe input 7 HL-DS-U4-WL Prbe input 6 Prbe input 4 Antenna RS-485 Lgical inputs 12VDC Pwer (+) center ; Rtrnic AG IN-E-HL-NT-V2_11

23 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 23 f 48 Dcument Ty pe HL-DS-PT2 Input 6: RTD Input 4: RTD Input 7: RTD Input 5: RTD RS-485 Lgical inputs 12VDC Pwer (+) center USB HL-DS-PT4 / HL-DS-PT4-WL Input 6: RTD Input 4: RTD RJ45 r WLAN RS-485 Lgical inputs 12VDC Pwer (+) center ; Rtrnic AG IN-E-HL-NT-V2_11

24 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 24 f 48 Dcument Ty pe HL-DS-R1 Relay 2 Relay 1 Nt used Nt used RS-485 Lgical Inputs 12VDC Pwer (+) center USB The relay cntacts are specified as fllws: Cntact material Silver ally Initial cntact resistance 100 mω Initial insulatin resistance Min. 1,000 MΩ at 500V DC Nminal switching capacity 1) 2 A 250 VAC Minimum switching pwer 1) 1,500 VA Maximum switching vltage 1) 250 V AC Maximum switching current 1) 2 A AC Minimum switching capacity 1) 100 ma, 5 V DC Expected life (min. peratins) Mechanical: 5 x 10 6 Electrical: N.O. 5 x 10 4 N.C. 3 x ) Resistive The DS-R-1 dcking statin is prvided with tw matching 4-pin cnnectrs. The pins f these cnnectrs are numbered n the cnnectr slder side (see pin-ut diagrams) ; Rtrnic AG IN-E-HL-NT-V2_11

25 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 25 f 48 Dcument Ty pe 3.3 Dcking statin inputs Depending n the mdel f dcking statin, the signals frm up t 4 additinal prbes can be prcessed by the HygrLg HL-NT HygrClip 2 prbes By default inputs 4, 5, 7 and 7 f dcking statins HL-DS-U1, HL-DS-U2, HL-DS-U4 and HL-DS- U4-W L are cnfigured by the factry t accept a HygrClip 2 prbe. Any mdel f HygrClip 2 prbe can be cnnected these using ne f the available extensin cables. See dcument E-M-HC2-acce ssries channel analg prbes with vltage utput Inputs 4, 5, 7 and 7 f dcking statins HL-DS-U1, HL-DS-U2, HL-U4 and HL-DS-U4-WL can als be cnfigured t accept ne f the fllwing: 1-channel analg prbe: T be cmpatible with the dcking statin the analg prbe must meet the fllwing requirements: supply vltage: 5 VDC, current cnsumptin: max. 10 ma, utput signal: 0 t max. 3.3 VDC. The dcking statin uses a 12-bit A/D cnverter t digitize the prbe analg signal and can be cnfigured t measure practically any parameter. Analg pressure prbe: this is a special case f analg prbe and is subject t the same cmpatibility requirements. When analg pressure prbe is selected, any input f the HygrLg HL-NT and dcking statin can be cnfigured t use the signal frm the pressure prbe t calculate any humidity parameter that requires barmetric pressure as an input value (example: mixing rati) channel analg prbes with current utput Dcking statin HL-DS-U4-420 is similar t dcking statin HL-DS-U4 with the difference that it accepts up t fur 3-wire single channel analg prbes with a 4-20 ma current utput signal. Each prbe input uses an internal 150 Ohm resistr t cnvert 4 20 ma t mv (nminal). The HW4 sftware allws a 2-pint adjustment f the ma t mv cnversin t cmpensate fr the tlerance n the 150 Ohm resistr (use Device Manager in HW4). The prbes are pwered by the dcking statin (supply vltage: 5 VDC, maximum current draw: 10 ma / prbe) Pt100 RTD 4-wire prbes Dcking statins HL-DS-PT2, HL-DS-PT4 and HL-DS-P T4-WL are designed fr 4-wire RTD prbes. These dcking statins allw the measurement f temperature cnditins within the range f -100 t 600 C. Accuracy depends n the class f the Pt100 RTD. Adjustment f the RTD inputs against a reference temperature is limited t a 1-pint adjustment (glbal ffset) Lgical inputs (n / ff) Several mdels f dcking statin allw the HygrLg HL-NT t prcess up t 2 lgical inputs. Typically this is used t mnitr a relay cntact, a dr cntact, etc ; Rtrnic AG IN-E-HL-NT-V2_11

26 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 26 f 48 Dcument Ty pe 3.4 Relay cntacts Dcking statin mdel HL-DS-R1 features tw independent relays, each with 3 cntacts: nrmally clsed, nrmally pen and cmmn. When cnfiguring the HygrLg HL-NT and dcking statin with the HW4 sftware, a number f cnditins can be defined that will cause the relay t be either energized r de-energized. The relays f the HL-DS-R1 dcking statin can be used t prvide a lcal indicatin f the fllwing: Out f limit values fr prbe inputs 1 t 3 f the HygrLg HL-NT Status f the tw lgical inputs f the DS-R-1 dcking statin Memry card errr External pwer failure Lw battery charge 4. Pin-ut diagrams Nte: all pin-ut diagrams are shwn frm the slder side f the matching cnnectr HygrLg HL-NT2 and HL-NT3: the prbe inputs are always cnfigured fr a HygrClip 2 prbe Dcking statins HL-DS-U1, HLDS--U2, HL-DS-U4, HL-DS-U4-420 and HL-DS-U4-WL: the prbe inputs can be cnfigured fr either a HygrClip 2 prbe r fr a 1-channel analg prbe HygrClip 2 prbe 1: RXD (UART) 2: GND (digital and pwer) 3: V+ (nminal 3.3 VDC) 4: nt used 5: nt used 6: nt used 7: TXD (UART) Analg 1-channel prbe 1: nt used 2: GND (pwer) 3: V+ (nminal 5 VDC, maximum 10 ma) 4: AGND (analg grund) 5: nt used 6: analg signal ( VDC r 4 20 ma 7: nt used ; Rtrnic AG IN-E-HL-NT-V2_11

27 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 27 f 48 Dcument Ty pe Dcking statins HL-DS-PT2, HL-DS-PT4 and HL-DS-PT4-WL: direct Pt100 RTD : DC (+) 2: measurement (+) 3: measurement (-) 4: DC (-) wire RTD 4 Dcking statins with lgical inputs : VDC 2: Input 1 3: Input 2 4: GND V Nte: an internal pull-dwn resistr sets each input t 0 when the cntact is pen. GND: nt used (eventually use fr a shield) Lgical Threshlds: lgical 1: 2.8 VDC, lgical 0: 0.7 VDC Dcking statin HL-DS-R1 with relay utputs : Nrmally clsed (relay de-energized) 2: Cmmn 3: Nrmally pen 4: Nt used ; Rtrnic AG IN-E-HL-NT-V2_11

28 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 28 f 48 Dcument Ty pe Dcking statins with RS-485 prt : 485 (-) 2: 485 (+) 3: GND (see nte) 4: DC + (see nte) Nte: use pins 3 and 4 t pwer multi-drpped instruments with a single external 12 VDC pwer supply with adequate ma rating. Pin 4 and the 12VDC pwer jack f the dcking statin are nt cnnected. Dcking statins with RS-232 prt Pin # RS TX 3 RX 5 GND 5. HW4 sftware The HygrLg HL-NT requires a dcking statin with the apprpriate interface t be able t cmmunicate with a PC with the ROTRONIC HW4 sftware installed (versin r higher). Detailed instructins are prvided in the HW4 manuals (see Supprting dcuments at the end f this manual). The HW4 instructin manuals are available n the HW4 installatin CD and can als be dwnladed frm ur web site. 5.1 Cmputer/Operating System Requirements The fllwing are the minimum values required t install and run HW 4 n a cmputer. It is highly recmmended t exceed these values. Prcessr: Pentium II, 450 MHz RAM: 128 MB Available hard disk space: 50 MB Mnitr: SVGA, 1024 x 768, 256 clrs Prts: ne free serial (COM) prt r ne free USB prt r Netwrk Interface Card / Ethernet LAN with ne free prt (RJ45 cnnectr) ; Rtrnic AG IN-E-HL-NT-V2_11

29 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 29 f 48 Dcument Ty pe 5.2 Operating System Cmpatibility Windws XP, NT4 with SP 6a r higher, Vista Windws 2000 with SP 2 r higher Windws Server 2003 HW4 was written fr the Micrsft.NET framewrk (versin 2.0) and requires this framewrk t be installed n the cmputer. The.NET framewrk ffers significant imprvements in the areas f netwrking and user security. When new sftware is being installed, the.net framewrk als eliminates the ptential prblem f cnflicting dynamic library files (DLL). Accrding t Micrsft, the.net framewrk will be used by all future Micrsft perating systems. 5.3 Settings and functins accessible nly with HW4 Device cnfiguratin settings User specific infrmatin (retained in the lgger) Custm text assciated with the lgger (30-character descriptin) Netwrk address f the lgger Language used in the lgger menu Date and time frmat / separatrs Decimal symbl Pressure unit (English) and mixed unit systems Individual input settings: - Prbe type (HygrClip 2 r analg) dcking statin nly - Prbe / input descriptin (maximum 12 characters) - Parameter t be calculated fr an individual input - Barmetric pressure: fixed value r read frm an input - Value t be used as fixed barmetric pressure - Alarm settings fr humidity, temperature and calculated parameter Display settings: - Display refresh rate - Turn display ff after xx minutes (display sleep functin) - Backlight peratin - Alternate the display - autmatically shw all inputs ne after the ther Keypad disable functins: - Disable entire keypad - Disable nly the MENU key Type f internal pwer surce: standard battery r rechargeable battery LED and Sund settings Cancel a latching alarm (LED n lgger and/r de-energizing ptinal dcking statin relays) Memry card settings: lg file frmat and memry management Prgramming f the ptinal inputs (dcking statin) ; Rtrnic AG IN-E-HL-NT-V2_11

30 Dcument cde HygrLg HL-NT data lgger: instructin manual Dcument title Rtrnic AG Bassersdrf, Switzerland Instructin Manual Page 30 f 48 Dcument Ty pe Data recrding functins Lgging functins (set individually fr each input, can be scheduled fr a future date / time): - Start date and time - Stp date and time - Lg measured values and cmputed parameter, r any cmbinatin - Custm text (used fr the lg file header - up t 43 characters) - User name, HW4-ID, HW4-serial number (used fr the lg file header) - Autmatic creatin f a new file after 200,000 data pints r at the end f each day, week r mnth Glbal prgramming f the lg functin f all inputs Data dwnlading (frm the lgger) and assciated functins HygrClip 2 prbe functins Device Manager (prbe cnfiguratin settings, simulatr functin, fail safe mde) Data recrding (at the prbe level) Prbe calibratin and adjustment (full functinality) Fr detailed instructins, see the fllwing HW4 sftware manuals: E-M-HW4v3-F2-013: Device Manager HygrLg HL-NT data lgger E-M-HW4v3-F2-001: Device Manager HC2 prbe series E-M-HW4v3-A2-001: Prbe Adjustment functin AirChip 3000 devices E-M-HW4v3-DR-001: Data Recrding Functin AirChip 3000 Devices 6. ERES regulatry cmpliance In rder t cmply with ERES regulatry requirements (Electrnic Recrds and Electrnic Signatures), the HygrLg HL-NT shuld be used tgether with the ROTRONIC HW4 sftware Prfessinal Editin (versin r higher). HW4 is designed t keep track f lgger cnfiguratin changes, prgramming changes and f any prbe adjustment. HW4 als keeps track f user events (main peratins perfrmed by each user) and self-events (sftware prblems). The recrds generated by HW4 are prtected with an electrnic authenticatin stamp, can be crss referenced and can be electrnically signed. IMPORTANT: In rder t cmply with ERES regulatry requirements, be sure t cnfigure bth the HygrLg HL-NT and the HW4 sftware as fllws: In HW4, create a user with full rights (administratr) and a passwrd (see HW4 manual - Users and Passwrds). After creating the first user, be sure t lg in as this user (see HW4 manual - Users and Passwrds - Change User). This enables bth the HygrLg HL-NT and the HW4 sftware t maintain a recrd f events and t assciate these with a specific user. Create additinal users with r withut limited rights, as per yur requirements. Enable HW4 t mnitr electrnic signatures and user events (see HW4 manual - Glbal Settings - Events) Enable HW4 t mnitr system events (see HW4 manual - Glbal Settings - General) Enable prtcls in HW4 (see HW4 manual - Device Manager - Device Manager Settings) ; Rtrnic AG IN-E-HL-NT-V2_11