Brocade Silkworm Switches Supports Management Module SM-BRC1000

Transcription

1 Brocade Silkworm Switches Supports Management Module SM-BRC1000 Device Management

2 Copyright Notice Document Copyright March 2002 by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS (c)(1)(ii) and FAR Liability Disclaimer Aprisma Management Technologies, Inc. ( Aprisma ) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES. Trademark, Service Mark, and Logo Information SPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go to All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns about trademark or copyright references, please send an to spectrum-docs@aprisma.com; we will do our best to help. Restricted Rights Notice (Applicable to licenses to the United States government only.) This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR (June 1987) Alternate III(g)(3) (June 1987), FAR (June 1987), or DFARS (c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license. Virus Disclaimer Aprisma makes no representations or warranties to the effect that the licensed software is virus-free. Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free. Contact Information Aprisma Management Technologies, Inc. 273 Corporate Drive Portsmouth, NH Phone: U.S. toll-free: Web site: Device Management Page 2 Brocade Silkworm Switches

3 Contents INTRODUCTION 4 Purpose and Scope...4 Required Reading...4 Supported Devices...5 The SPECTRUM Model...5 TASKS 7 DEVICE VIEW 8 Interface Icons...9 Interface Icon Subviews Menu...10 Secondary Address Panel...11 DEVICE TOPOLOGY VIEW 12 SWITCHING INFORMATION 13 System Information View...13 Environment Information View...17 Fabric Information View...17 Agent Community Information View...18 Fibre Channel Port Information View...18 Name Server Information View...22 FW Thresholds Information View...23 FW Class Area Information View...24 Event Information View...25 End Devices RLS Information View...25 Bloom Performance Alpa Information View Bloom Performance End to End Performance View Bloom Performance Filter Base Information View Trunking Information View Trunk Group Information APPLICATION VIEWS 29 Main Application View Supported Applications Common Applications Device-Specific MIBs PERFORMANCE VIEWS 32 CONFIGURATION VIEWS 33 Device Configuration View MODEL INFORMATION VIEW 35 TRAPS, EVENTS, AND ALARMS 36 Standard Trap Support Device-Specific Trap Support Proprietary Trap Descriptions INDEX 39 Device Management Page 3 Brocade Silkworm Switches

4 Introduction This section introduces the SPECTRUM Device Management documentation for the Brocade Silkworm Switch. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 5) The SPECTRUM Model (Page 5) Purpose and Scope Use this document as a guide for managing the Brocade Silkworm Switch devices described on Page 5 with SPECTRUM management module SM-BRC1000. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Brocade Silkworm Switch devices through software models in your SPECTRUM database. Information specific to SM-BRC1000 is what is primarily included in this document. For general information about device management using SPECTRUM and explanations of SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice Device Management Page 4 Brocade Silkworm Switches

5 Introduction Supported Devices SPECTRUM management module SM-BRC1000 currently lets you model the following Brocade Silkworm Switch. SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Fibre Channel Switch SilkWorm port Fibre Channel Switch SilkWorm 3200 Entry Fabric Switch SilkWorm 3800 Enterprise Fabric Switch SilkWorm 3900 Enterprise Fabric Switch SilkWork Director The SPECTRUM Model Supported Devices The model type for the Brocade Silkworm Switch devices is SilkwormSw. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Model Name XYZ_Mxxx Figure 1: Large Device icon appears in Device Topology, Location, and Device Interface views. Device Icons Small Device icon appears in Topology and Application views Model Name XYZ_Mxxx Device Management Page 5 Brocade Silkworm Switches

6 Introduction The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Fault Management Accesses the... Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation. Device Device View (Page 8) Device Topology Device Topology View (Page 12) Application Application Views (Page 29) Configuration Configuration Views (Page 33) Model Information Primary Application Model Information View (Page 35) Menu options that let you select either Gen. Bridge App or MIB-II as the primary application. The SPECTRUM Model The rest of this document covering management module SM-BRC1000 is organized as follows: Tasks (Page 7) Device View (Page 8) Device Topology View (Page 12) Application Views (Page 29) Performance Views (Page 32) Configuration Views (Page 33) Model Information View (Page 35). Device Management Page 6 Brocade Silkworm Switches

7 Tasks This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information View (Page 35) Alarm Thresholds (set) Interface Icon Subviews Menu (Page 10) Port Status (check/change) Secondary Address Panel (Page 11) Topology (check) Device Topology View (Page 12) Configuration Information (check) Configuration Views (Page 33) IP Address (find/change) Device View (Page 8) Secondary Address Panel (Page 11) Network Type (check) Network Type Label (Page 10) Performance (check) Device View (Page 8) Interface Icons (Page 9) Performance Views (Page 32) Device Management Page 7 Brocade Silkworm Switches

8 Device View This section describes the Device view and subviews available for models of Brocade Silkworm Switch devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Device > Interface. This view (Figure 2) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 2: Device View SpectroGRAPH: Router Device: Model Name File View Tools Bookmarks Help Model Name Contact Description Location Model Name XYZ_Mxxx 1 ON Ethernet ei0 0:0:1D:F:FD:B ON ATM CPU Network Address Primary Application Gen Bridge App Filter Physical Interface Description Device Icon 3 ON 4 ATM 7B Sys Up Time Manufacturer Device Type Serial Number Interface Options Panel ATM 8B ON 5 ON SFTWARLPBK lo0 0:0:1D:F:FD:B ON ATM port CPU ON ATM 7B ON ATM 8B ON ATM8023 zn1 0:0:1D:F:FD:B ON AAL5 UAAL5 10 ON ATM 7A ON ATM 7B ON ATM 8B ON ATM 8B2 Interface Icons Model Name of type XYZ_Mxxx of Landscape node: Primary Device Management Page 8 Brocade Silkworm Switches

9 Device View Interface Icons Figure 3 shows a close-up of an Interface icon from the Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 3: a b c d e f a Interface Icon b 1 ON ethernet fxp0 0:0:1D:F:FD:B Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label c d e f Interface Icons Interface Number Label This label displays the interface (port) number. IF Status Label This label displays the current status of the interface for the primary application selected, e.g., Gen Rtr App or MIB-II App. Table 1 lists the possible label color representations. Note that the color of the label also depends on the interface s current Administrative Status, which you set in the Interface Configuration view. This view can be accessed by double-clicking the Interface Type label. Table 1: Color Interface Status Label Colors Operational Status Administrative Status Green up up ON Blue down down OFF Yellow down up OFF Label Text Red testing testing TEST Interface Type Label This label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Device view, see the SPECTRUM Views documentation. Device Management Page 9 Brocade Silkworm Switches

10 Device View Network Type Label This label identifies the type of network to which the interface is connected. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the IF Address Translation Table. IP Address Label This label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 11), which lets you change the address and mask for the interface. Interface Icon Subviews Menu Table 2 lists the device-specific interface Icon Subviews menu options and the views to which they provide access. Detail Table 2: Option IF Configuration Sub-Layer Information Address Translation Table Secondary Address Panel Thresholds Model Information Trap Configuration Interface Icon Subviews Menu Interface Icon Subviews Menu Accesses the... Interface Detail view, which displays packet, error, and discard breakdown statistics for the interface. Interface Configuration view. (See SPECTRUM Views). Sub-Layer Information view. (See SPECTRUM Views). Interface Address Translation Table, which identifies the physical and network address for the interface. Secondary Address Panel (Page 11). Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface. Model Information View (Page 35). Trap Configuration view (see the How to Manage Your Network with SPECTRUM documentation). Device Management Page 10 Brocade Silkworm Switches

11 Device View Secondary Address Panel Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. Device Management Page 11 Brocade Silkworm Switches

12 Device Topology View This section describes the Device Topology view available for models of the Brocade Silkworm Switch devices. Access: From the Icon Subviews menu for the Device icon, select DevTop > interface. The Device Topology view (Figure 4) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device View (Page 8). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 4: Device Topology View SpectroGRAPH: Device Topology: Model Name File View Tools Bookmarks Help Graphic of <manufacturer> Device Model Name XYZ_Mxxx 1 ON 2 ON 3 ON Ethernet ei0 0:0:1D:F:FD:B6 ATM A2 0:0:1D:F:FD:B6 ATM CPU 0:0:1D:F:FD:B Model Name of type Model Type of Landscape node: Primary Device Management Page 12 Brocade Silkworm Switches

13 Switching Information This section describes the switching information available for the Brocade Silkworm devices. The following views provide switching information for the Brocade Silkworm devices: System Information View (Page 13) Environment Information View (Page 17) Fabric Information View (Page 17) Agent Community Information View (Page 18) Fibre Channel Port Information View (Page 18) Name Server Information View (Page 22) FW Thresholds Information View (Page 23) FW Class Area Information View (Page 24) Event Information View (Page 25) End Devices RLS Information View (Page 25) Bloom Performance Alpa Information View (Page 26) Bloom Performance End to End Performance View (Page 26) Bloom Performance Filter Base Information View (Page 27) Trunking Information View (Page 28) Trunk Group Information (Page 28) System Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > System. This view is divided into four separate sections and provides the following information. General Information Firmware Vers. The current version of the firmware. Soft Ser. Num. The serial number of the software. Oper Status The current operational status of the switch. Table 3 displays the possible states. Device Management Page 13 Brocade Silkworm Switches

14 Switching Information System Information View. Table 3: Possible Operational States Table 4: Admin Status States State Definition Sate Definition Online Offline Testing Faulty The switch is accessible by an external Fibre Channel Port. The switch is not accessible. The switch is in a built-in test mode and is not accessible. The switch is not operational. Telnet Admin Status The desired administrative status of the Telnet shell. By setting it to terminated, the current Telnet shell task is deleted. When this variable is read, it reports the value last set through SNMP. Admin Status The desired administrative status of the switch. A management station may place the switch in a desired state by setting this button accordingly. Table 4 defines the possible states. Online Offline Testing Faulty Reboot Fastboot This switch is accessible by a an external Fiber Channel Port. The switch is not accessible. The switch is in a built-in test mode and is not accessible. The switch is not operational. Set the switch to reboot in one second. Sets the switch to fastboot in one second. Fast causes the switch to boot but skip over the POST. Track Changes String Displays the track changes string. This is for traps only. Device Management Page 14 Brocade Silkworm Switches

15 Switching Information Last Updated Boot Date The date and time when the system last booted, in displaybale textual format. Boot Prom The date when the boot PROM was last updated, in displayable textual format. FLASH The date when the FLASH was last updated, in displayable textual format. Firmware The date when the firmware was last updated, in displayable textual format. FLASH Information Admin Status The desired state of the FLASH. Table 5 shows the possible values. Table 5: State swcurrent swfwupgrade swcfupload swcfdownload System Information View FLASH Admin States Definition The FLASH contains the current firmware image or config file. The firmware in the FLASH is to be upgraded from the host specified. The switch config file is to be uploaded to the host specified. The switch config file is to be downloaded from the host specified. Oper Status The operational status of FLASH. Table 6 displays the possible states. Device Management Page 15 Brocade Silkworm Switches

16 Switching Information Table 6: swcurrent State swfwupgraded swcfuploaded swcfdownloaded FLASH Operational States Definition The FLASH contains the current firmware image or config file. Contains the image upgraded from the swflashdlhost.0. The switch configuration file has been uploaded to the host. The switch configuration file has been downloaded from the host. Password The password to be used for FTP transfer of files in the download or upload operation. User The user name on the host to download or upload a relevant file to or from the FLASH. Host The name or IP address (in dot notation) of the host to download or upload a relevant file to the FLASH. System Information View File The name of the file to be downloaded or uploaded. Misc Information POST Result The result of the power-on startup (POST) diagnostics. Sensors The number of sensors inside the switch. Beacon Admin Status The desired status of the switch beacon. When the beacon is set to on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is set to off, each LED will be in its regular status indicating color and state. Beacon Oper Status The current operational status of the switch beacon. When the beacon is on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off, each LED will be in their its regular status indicating color and state. Device Management Page 16 Brocade Silkworm Switches

17 Switching Information Environment Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Environment. This view provides the Sensor Table and the following information. Num Sensor The number of sensors inside the switch. Sensor Table Index Identifies the sensor. Type Identifies the sensor type. Status The current status of the sensor. Value The current value (reading) of the sensor. The value, , represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. In V2.0, the temperature sensor value will be in Celsius; the fan value will be in RPM (revolution per minute); and the power supply sensor reading will be unknown. Environment Information View Info Additional displayable information on the sensor. In V2.x, it contains the sensor type and number in textual format. Fabric Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Fabric. This view provides the following information. Domain ID The current Fibre Channel domain ID of the switch. To set a new value, the switch (swadmstatus) must be in offline or testing state. Principal Switch Indicates whether the switch is the Principal switch as per FC-SW. Num Neighbors The number of Inter-Switch Links in the (immediate) neighborhood. Neighbor Table Index Identifies the neighbor ISL entry. Local Port This is a port that has an ISL to another switch. Device Management Page 17 Brocade Silkworm Switches

18 Switching Information Remote Domain The Fibre Channel domain on the other end of the ISL. Remote Port The port index on the other end of the ISL. Baud Rate The baud rate of the ISL. State The current state of the ISL. Cost The current link cost of the ISL. Remote Name The World_wide_Name of the remote port. Agent Community Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Agent Comm. This view provides the following information. Agent Community Index Identifies the SNMPv1 Community entry. Agent Community Information View Agent Community String The Community string supported by the agent. If a new value is set successfully, it takes effect immediately. Agent Trap Recipient The trap recipient associated with the Community. If a new value is set successfully, it takes effect immediately. Fibre Channel Port Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FC Ports. This view provides the Port Table defined below: Port Capacity The maximum number of Fibre Channel ports on this switch. It includes G_Port, F_Port, FL_Port and any other types of Fibre Channel port. Index Identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. E.g. port index 1 correspond to port number 0. Device Management Page 18 Brocade Silkworm Switches

19 Switching Information Type Identifies the type of switch port. It may be of type stitch, flannel, loom, bloom, rdbloom or wormhole. Physical State Identifies the physical state of the port. Table 7 show the possible values. Table 7: Fibre Channel Port Information View diagfault lockref Possible Physical States (Continued) State Definition The port failed diagnostics (defective G_Port or FL_Port card or motherboard. the port is locking to the reference signal. Table 7: State nocard nogbic laserfault nolight nosync insync portfault Possible Physical States Definition No card present in this switch slot. No GBIC module in this port. The module is signaling a laser fault (defective GBIC). The module is not receiving light. The module is receiving light but is out of sync. The module is receiving light and is in sync. The port is marked faulty (defective GBIC, cable or device). Oper Status Identifies the operational status of the port. The online state indicates that user frames can be passed. The unknown state indicates that the port module is physically absent (see swfcportphystate). Admin Status The desired state of the port. A management station may place the port in a desired state by setting this object accordingly. The testing state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swfcportadmstatus is then changed to either the online or testing states, or remains in the offline state. Device Management Page 19 Brocade Silkworm Switches

20 Switching Information Link State The link state of the port. The possible value are: enabled, disabled, and loopback. The port may transmit frames through an internal path to verify the health of the transmitter and receiver path. TX Type The media transmitter type of the port. Table 8 show the possible values. Table 8: State unknown lw sw ld cu Note: Possible TX States Definition Cannot determine the port driver. Long wave laser. Short wave laser. Long wave LED. Copper Electral. Not that here is a new type of GBIC which has a serial ID and will be mapped as unknown for the current firmware revision. Fibre Channel Port Information View TX Words Counts the number of Fibre Channel words that the port has transmitted. RX Words Counts the number of Fibre Channel words that the port has received. TX Frames Counts the number of (Fibre Channel) frames that the port has transmitted. RX Frames Counts the number of (Fibre Channel) frames that the port has received. RX C2 Frames Counts the number of Class 2 frames that the port has received. RX C3 Frames Counts the number of Class 3 frames that the port has received. RX LCs Counts the number of Link Control frames that the port has received. RX Mcasts Counts the number of Multicast frames that the port has received. Device Management Page 20 Brocade Silkworm Switches

21 Switching Information Too Many RDYs Counts the number of times when RDYs exceeds the frames received. No Tx Credits Counts the number of times when the transmit credit has reached zero. RX Enc In Frs Counts the number of encoding error or disparity error inside frames received. Rx CRCs Counts the number of CRC errors detected for frames received. RX Truncs Counts the number of truncated frames that the port has received. RX Too Longs Counts the number of received frames that are too long. Rx Bad EOFs Counts the number of received frames that have bad EOF delimiter. RX Enc Out Frs Counts the number of encoding error or disparity error outside frames received Fibre Channel Port Information View RX Bad Os Counts the number of invalid Ordered Sets received. C3 Discards Counts the number of Class 3 frames that the port has discarded. Tx Mcasts Counts the number of Multicast frames that has been transmitted. Mcasts Time Outs Counts the number of Multicast frames that has been timed out. Lip Ins Counts the number of Loop Initialization that has been initiated by loop devices attached. Lip Outs Counts the number of Loop Initializations that has been initiated by the port. Lips Last Alpa The Physical Address (AL_PA) of the loop device that initiated the last Loop Initialization. World Wide Name The World_Wide_Name of the Fibre Channel port. The contents of an instance are in the IEEE extended format as specified in FC-PH; the 12-bit Device Management Page 21 Brocade Silkworm Switches

22 Switching Information port identifier represents the port number within the switch. Port Speed The desired baud rate for the port. It can have the values of 1GB(1), 2GB (2) or Auto-Negotiate (3). Name Server Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Name Server. This view provides the following information. Index The Name Server database entry. Port ID The Fibre Channel port address. Port Type The type of port. N_Port, NL_Port, etc., for this entry. The type is defined in FC-GS-2. Port Name The Fibre Channel World_Wide Name of the port entry. Port Symbol The contents of a Symbolic Name of the port entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its Name Server Information View contents. This variable corresponds to the 'contents of the Symbolic Name, without the first byte. Node Name The Fibre Channel World_Wide Name of the associated node as defined in FC-GS-2. Node Symbol The contents of a Symbolic Name of the node associated with the entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its contents. This variable corresponds to the contents of the Symbolic Name, without the first byte (specifying the length). IPA The Initial Process Associator of the node for the entry as defined in FC-GS-2. IP Address The IP address of the node for the entry as defined in FC-GS-2. The format of the address is in IPv6. COS The class of services supported by the port. The value is a bit-map defined as follows: 0 is class F, 1 is class 1, and 2 is class 2 etc. Device Management Page 22 Brocade Silkworm Switches

23 Switching Information FC-4s The FC-4s supported by the port as defined in FC-GS-2. IP Nx_Port IpAddress of the Nx_port for the entry. World Wide Name The World Wide Name (WWN) of the Fx_port for the entry. Hard Address The 24-bit hard address of the node for the entry. FW Thresholds Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FW Thresholds. This view provides the following information. Index An entry for each threshold in this table. Status Identifies if a threshold is enabled or disabled Name The name of the threshold. Label Label of the threshold. FW Thresholds Information View Current Val A current counter of the threshold. Last Event The last event type of the threshold. Last Event Time The last event value of the threshold. Last State The last event time of the threshold Behavior Type A behavior of which the thresholds generate events. Behavior Int An integer of which the thresholds generate continuous events. Device Management Page 23 Brocade Silkworm Switches

24 Switching Information FW Class Area Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FW Class. This view provides the following information. Class Area Index The class type. Write Thresh Vals Applies the value changes. Default Unit A Default unit string name for a threshold area. Default Timebase A Default timebase for the current threshold counter. Default Low A Default low threshold value. Default High A Default high threshold value. Default Buf Size A Default buffer size value. Cust Unit A custom unit string name for a threshold area. FW Class Area Information View Cust Timebase A custom timebase for the current threshold counter. Cust Low A custom low threshold value. Cust High A custom high threshold value. Cust Buf Size A custom buffer size value. Thresh Level A level where all the threshold values are set at. Write Act Vals SwFwis is set to apply act value changes. Default Changed Acts Default action matrix for changed event. Default Exceed Acts Default action matrix for exceeded event. Default Below Acts Default action matrix for below event. Default Above Acts Default action matrix for above event. Default In Between Acts Default action matrix for in-between event. Device Management Page 24 Brocade Silkworm Switches

25 Switching Information Cust Changed Acts Custom action matrix for changed event. Cust Exceeded Acts Custom action matrix for exceeded event. Cust Below Acts Custom action matrix for below event. Cust Above Acts Custom action matrix for above event. Cust in Between Acts Custom action matrix for in-between event. Valid Acts Matrix of valid acts for an class/area Act Level A level where all the actions are set. Event Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Events. This view provides the following information. Number of Entries The number of entries in the Event Table. Event Index The event entry. Event Information View Event Time Info The date and time when this event occurred, in textual format. Event Level The severity level of this event entry. Event Repeat Count How many times this particular event has occurred. Event Descr The textual description of the event. End Devices RLS Information View Access: From the Icon Subviews menu for the Device icon, select Switching Information > End Devices. This view provides the following information. Port The port number of the end device. Alpa The alpa of the end device. Device Management Page 25 Brocade Silkworm Switches

26 Switching Information Post ID The Fibre Channel port address. Link Fail Count Link failure count for the end device. Sync Loss Count Sync loss count for the end device. Sig Loss Count Sig loss count for the end device. Proto Error Count Protocol error count for the end device. Invalid Word Count Invalid word count for the end device. Invalid CRC Count Invalid CRC count for the end device. Bloom Performance Alpa Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Bloom Perf Alpa. This view provides the following information. Alpa Port The port index of the switch. Bloom Performance Alpa Information View Alpa Index The ALPA index. There can be 126 ALPA values. Alpa The ALPA values. These values range between x01 and x'ef(1 to 239). ALPA value x'00' is reserved for FL_Port If Alpa device is invalid, then it will have -1 value. Alpa CRC Count Get CRC count for given ALPA and port. This monitoring provides information on the number of CRC errors occurred on the frames destined to each possible ALPA attached to a specific port. Bloom Performance End to End Performance View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Bloom Perf EE. The view provides the following information. EE Port The port number of the switch. EE Ref Key The reference number of the counter. This reference is assigned when a filter is created. Device Management Page 26 Brocade Silkworm Switches

27 Switching Information Bloom Performance Filter Base Information View EE CRC End to End CRC error for the frames that matched the SID-DID pair. EE FCW Rx End to End count of Fibre Channel words (FCW), received by the port, that matched the SID-DID pair. EE FCW Tx End to End count of Fibre Channel words (FCW), transmitted by the port, that matched the SID- DID pair. EE SID SID info by reference number. SID (Source Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N- Port from which the frame was sent. EE DID DID info by reference number. DID (Destination Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N- Port to which the frame was sent. Bloom Performance Filter Base Information View Access: From the Icon Subviews menu Device icon, select Switching Information > Bloom Perf Filter. This view provides the following information. Filter Port The port number of the switch. Filter Ref Key The reference number of the filter. This reference is assigned when a filter is created. In SNMP, Index starts at one instead of 0. Add one to actual ref key. Filter Count Statistics of filter based monitor. Filter based monitoring provides information about a filter hit count such as Read command, SCSI, IP traffic, and SCSI Read/Write Filter Alias The trunking status of the switch - whether the switch supports the trunking feature or not. Device Management Page 27 Brocade Silkworm Switches

28 Switching Information Trunking Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Trunking. Trunk Port Index The switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. Trunk Group Number A logical entity which specifies the Group Number to which the port belongs to. If this value is 0 it means the port is not Trunked. Trunk Master Port number that is the trunk master of the group. The trunk master implicitly defines the group. All ports with the same master are considered to be part of the same group. Port Trunked The current state of trunking for a member port. Trunking Information View Trunk Group Master The master port id for the TrunkGroup. Trunk Group Tx The aggregate value of the transmitted words by this TrunkGroup. Trunk Group Rx The aggregate value of the received words by this TrunkGroup. Trunk Group Information Access: From the Icon Subviews menu for the Device icon, select Switch Information > Trunking Group. Trunk Group Number A logical entity which specifies the Group Number to which port the belongs. Device Management Page 28 Brocade Silkworm Switches

29 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Brocade Silkworm Switch devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 5: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View document. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Contact Description Location Network Address System Up Time Manufacturer Device Type Serial Number Model Name Model 6E132_25 Type Help Model Name of type <model type> of Landscape node: Primary Device Management Page 29 Brocade Silkworm Switches

30 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Applications associated with non proprietary. Device-Specifc Applications. Common Applications For the most part, these applications represent the non proprietary MIBs supported by devices. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Refer to these documents when your devices support these applications. Note: The documents listed below (in bold font) are available for viewing at: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - OSPF - OSPF2 - BGP4 - VRRP - RFC 2932 Bridging Applications - Ethernet Special Database - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation - QBridge MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Transmission Applications - FDDI - Point to Point - DS1 - DS3 - RS WAN Supported Applications Device Management Page 30 Brocade Silkworm Switches

31 Application Views - Frame Relay - Token Ring - Ethernet - Fast Ethernet - RFC 1317App - RFC 1285App - RFC 1315App App - SONET Technology Applications - APPN - ATM Client - DHCP - DLSw - PNNI - RFC 1316App - RFC RFC RFC RFC 2925 DOCSIS Applications - DOCSISCblDvApp - DOCSISQOSApp - DOCSISBPI2App - DOCSISBPIApp - DOCSISIFApp Supported Applications Digital Subscriber Line (DSL) Applications - ADSL Device-Specific MIBs SPECTRUM imports the following device-level proprietary MIBs into its database: SW-Mib These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. There are no device-specific applications supported for the Brocade Silkworm Switches at this point. Device Management Page 31 Brocade Silkworm Switches

32 Performance Views This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates,% error, etc. A typical view is shown in Figure 6. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Figure 6: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Model Name Contact Description Location Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. 0:40:0 0:30:0 0:20:0 Value Average Peak Value Log * Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded 0 *Frames per second Graph Properties Scroll to Date-Time Detail type routing of type IP Routing of Landscape node: Primary Device Management Page 32 Brocade Silkworm Switches

33 Configuration Views This section describes the various Configuration views available for models of the Brocade Silkworm Switch devices in SPECTRUM. Configuration views let you see and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Brocade Silkworm Switch devices: Device Configuration View (Page 33) Device Configuration View Access: From the Icon Subviews menu for the Device icon, select Configuration. A typical Device Configuration view is shown in Figure 7. Generally, this view includes a few fields that display device information as well as an Interface Configuration Table that lists interface parameters, some of which can be changed (see SPECTRUM Views). Some Device Configuration views include one or more buttons that provide access to device-specific configuration information. These are described below.. Model Name Description Location Figure 7: File View Tools Bookmarks Sort Contact Status Find Update Device Configuration View SpectroGRAPH: Model Name Contact Manufacturer Sys Up Time Configuration View Net Address Device Type Serial Number Number of Interfaces Interface Address Table Interface Configuration Table Help Index Description Type Bandwidth Physical Addre IP Address of type Model of Landsape: Primary Device Management Page 33 Brocade Silkworm Switches

34 Configuration Views Device Configuration View IF Address Translation Refer to the SPECTRUM Views documentation. Device Management Page 34 Brocade Silkworm Switches

35 Model Information View This section provides a brief overview of the Model Information view. Model Information views display administrative information about devices and their applications and let you set thresholds and alarm severity for the devices. Figure 8 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Model Name Description Location Figure 8: Model Information View SpectroGRAPH: Model Name File View Tools Bookmarks MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String DCM TimeOut DCM Retry Contact Manufacturer SysUpTime Model Information View Communication Information Net Address Device Type Serial Number General Information Condition Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Community Name Mgnmt Protocol Help Poll Interval Poll Status Log Ratio Last Successful Poll True Poll / Log Information Logged Polled IP Address of Model Type of Landscape: Primary Device Management Page 35 Brocade Silkworm Switches

36 Traps, Events, and Alarms This section provides you with an overview of trap, event, and alarm support. This section describes any device-specific events and alarms supported by the Brocade Silkworm Switches (SM-BRC1000) management module. Standard Trap Support Device-Specific Trap Support Device-Specific Trap Support The supported device-specific traps are listed in Table 10 (Page 37). Standard Trap Support The following standard traps are supported. Table 9: Standard Trap Support Standard Trap Name OID coldstart 0.0 warmstart 1.0 linkdown 2.0 linkup 3.0 authenticationfailure 4.0 egpneighborloss 5.0 Device Management Page 36 Brocade Silkworm Switches

37 Traps, Events, and Alarms Table 10: BROCADE-SW-TRAP-MIB Traps Device-Specific Trap Support Trap Name OID Variable Bindings Event Generated Alarm Generated Alarm Severity swfault (Page 38) x043b0001 0x043b0001 Red swsensorscn (Page 38) swscportscn (Page 38) sweventtrap (Page 38) swfabricwatchtrap (Page 38) swtrackchangestrap (Page 38) x043b0002 0x043b0002 Yellow 0x043b0003 0x043b0003 Yellow 0x043b0004 0x043b0004 Yellow 0x043b0005 0x043b0005 Yellow x043b0006 0x043b0006 Yellow Device Management Page 37 Brocade Silkworm Switches

38 Traps, Events, and Alarms Proprietary Trap Descriptions swfault A swfault(1) is generated whenever the diagnostics detect a fault with the switch. swsensorscn A swsensorscn(2) is generated whenever an environment sensor changes its operational state, for example a fan stops working. The VarBind in the Trap Data Unit shall contain the corresponding instance of the sensor status, sensor index, sensor type, sensor value (reading) and sensor information. Note that the sensor information contains the type of sensor and its number in textual format. swscportscn A swfcportscn(3) is generated whenever an FC_Port changes its operational state. For example, the FC_Port goes from on-line to offline. The VarBind in the Trap Data Unit shall contain the corresponding instance of the FC_Port's operational status and index. sweventtrap This trap is generated when an event with a level at or below sweventtraplevel occurs. Device-Specific Trap Support swfabricwatchtrap This is the trap to be sent by Fabric Watch to indicate that an event has occurred. swtrackchangestrap This is the trap to be sent for tracking login/logout/config changes. Device Management Page 38 Brocade Silkworm Switches

39 Index A Address Interface IP 10 Physical (MAC) 10 Translation 11 Admin Status 9 Agent Trap Recipient 18 Alarm Generated 37 Alpa 25 Alpa CRC Count 26 Applications 29 B Baud Rate 18 Beacon 16 Behavior Int 23 Behavior Type 23 Boot Prom 15 C Configuration Device 33 COS 22 Cust Timebase 24 D DevTop Views 12 Documentation 4 Domain ID 17 E Event Generated 37 F FC-4s 23 Filter Alias 27 Filter Count 27 Firmware 15 FLASH 15 H Hard Address 23 Hardware 5 I Icons Device 5 Interface 9 Interface Type, Device 9 IP Address 22 IPA 22 L Lips Ins 21 Lips Last Alpa 21 Lips Outs 21 M Management Tasks 7 Mask 11 Model Information 35 Types of 5 Device Management Page 39 Brocade Silkworm Switches

40 Index Index N Neighbor Table 17 Network I/O ports 12 Network Type 10 Node Symbol 22 O OID 37 P Password 16 Performance Statistics 32 Port Capacity 18 Port Number, Device 9 Port Symbol 22 Port Table 18 Port Trunked 28 POST Result 16 Principal Switch 17 R Remote Domain 18 RX C2 20 RX C2 Frames 20 RX C3 20 RX LCs 20 RX Words 20 S Sensor Table 17 Serial ports 12 Statistics Routing Frame Transmission 32 T Telnet Admin Status 14 Threshold Information 10 Track Changes String 14 Trap Name 37 Trap Support 36 Troubleshooting 7 Trunk Group Number 28 Trunk Group Rx 28 Trunk Master 28 Trunk Port 28 TX Frames 20 TX Type 20 TX Words 20 V Valid Acts 25 W World Wide Name 21 Write Thresh Vals 24 Device Management Page 40 Brocade Silkworm Switches