MPE/iX HP 3000 Series 99X. Software Startup Manual

Transcription

1 900 Series HP 3000 Computer Systems MPE/iX HP 3000 Series 99X Softwre Strtup Mnul ABCDE HP Prt No Printed in USA 1994 R3404 E0494

2 The informtion ontined in this doument is sujet to hnge without notie Hewlett-Pkrd mkes no wrrnty of ny kind with regrd to this mteril, inluding, ut not limited to, the implied wrrnties of merhntility or tness for prtiulr purpose Hewlett-Pkrd shll not e lile for errors ontined herein or for diret, indiret, speil, inidentl or onsequentil dmges in onnetion with the furnishing or use of this mteril Hewlett-Pkrd ssumes no responsiility for the use or reliility of its softwre on equipment tht is not furnished y Hewlett-Pkrd The unuthorized use of Hewlett-Pkrd proprietry progrms to ongure system running the MPE/iX operting system n use n error nd render the system inoperle This doument ontins proprietry informtion whih is proteted y opyright All rights re reserved Reprodution, dpttion, or trnsltion without prior written permission is prohiited, exept s llowed under the opyright lws Copyright 1994 y Hewlett-Pkrd Compny Use, duplition, or dislosure y the US Government is sujet to restritions s set forth in suprgrph () (1) (ii) of the Rights in Tehnil Dt nd Computer Softwre luse t DFARS Rights for non-dod US Government Deprtments nd genies re s set forth in FAR () (1,2) Hewlett-Pkrd Compny 3000 Hnover Street Plo Alto, CA USA Restrited Rights Legend

3 Prefe MPE/iX, Multiprogrmming Exeutive with Integrted POSIX, is the ltest in series of forwrd-omptile operting systems for the HP 3000 line of omputers In HP doumenttion nd in tlking with HP 3000 users, you will enounter referenes to MPE XL, the diret predeessor of MPE/iX MPE/iX is superset of MPE XL All progrms written for MPE XL will run without hnge under MPE/iX You n ontinue to use MPE XL system doumenttion, lthough it my not refer to fetures dded to the operting system to support POSIX (for exmple, hierrhil diretories) Finlly, you my enounter referenes to MPE V, whih is the operting system for HP 3000s, not sed on PA-RISC rhiteture MPE V softwre n e run on the PA-RISC (Series 900) HP 3000s in wht is known s omptiility mode iii

4 iv

5 Conventions UPPERCASE In syntx sttement, ommnds nd keywords re shown in upperse hrters The hrters must e entered in the order shown; however, you n enter the hrters in either upperse or lowerse For exmple: COMMAND n e entered s ny of the following: ommnd Commnd COMMAND It nnot, however, e entered s: itlis old itlis puntution underlining omm om_mnd ommnd In syntx sttement or n exmple, word in itlis represents prmeter or rgument tht you must reple with the tul vlue In the following exmple, you must reple lenme with the nme of the le: COMMAND lenme In syntx sttement, word in old itlis represents prmeter tht you must reple with the tul vlue In the following exmple, you must reple lenme with the nme of the le: COMMAND(lenme) In syntx sttement, puntution hrters (other thn rkets, res, vertil rs, nd ellipses) must e entered extly s shown In the following exmple, the prentheses nd olon must e entered: (lenme):(lenme) Within n exmple tht ontins intertive dilog, user input nd user responses to prompts re indited y underlining In the following exmple, yes is the user's response to the prompt: Do you wnt to ontinue? >> yes v

6 Conventions (ontinued) { } In syntx sttement, res enlose required elements When severl elements re stked within res, you must selet one In the following exmple, you must selet either ON or OFF: ON COMMAND OFF [ ] In syntx sttement, rkets enlose optionl elements In the following exmple, OPTION n e omitted: COMMAND lenme [OPTION] When severl elements re stked within rkets, you n selet one or none of the elements In the following exmple, you n selet OPTION or prmeter or neither The elements nnot e repeted OPTION COMMAND lenme prmeter [ ] In syntx sttement, horizontl ellipses enlosed in rkets indite tht you n repetedly selet the element(s) tht pper within the immeditely preeding pir of rkets or res In the exmple elow, you n selet prmeter zero or more times Eh instne of prmeter must e preeded y omm: [,prmeter][] In the exmple elow, you only use the omm s delimiter if prmeter is repeted; no omm is used efore the rst ourrene of prmeter: [prmeter][,] vi

7 Conventions (ontinued) In syntx sttement, horizontl ellipses enlosed in vertil rs indite tht you n selet more thn one element within the immeditely preeding pir of rkets or res However, eh prtiulr element n only e seleted one In the following exmple, you must selet A, AB, BA, orb The elements nnot e repeted A B In n exmple, horizontl or vertil ellipses indite where portions of n exmple hve een omitted 1 In syntx sttement, the spe symol 1 shows required lnk In the following exmple, prmeter nd prmeter must e seprted with lnk: (prmeter)1(prmeter) 4 5 The symol 4 5 indites key on the keyord For exmple, 4RETURN5 represents the rrige return key or 4Shift5 represents the shift key 4CTRL5hrter 4CTRL5hrter indites ontrol hrter For exmple, 4CTRL5Y mens tht you press the ontrol key nd the Y key simultneously vii

8

9 Contents 1 Overview Mterils Needed to Complete Instlltion 1-1 DTS (Terminl I/O) 1-1 Additionl produts 1-2 The NS3000/XL produt 1-2 NewWve Oe/XL produts 1-2 HP ALLBASE/4GL Strting the System Booting the System 2-1 Conguring System Disks Using VOLUTIL 2-7 Instlling Additionl Produts 2-7 Conguring Dt Communition 2-8 Setting Psswords 2-12 Creting Bkup Tpe 2-13 Setting Jo nd Session Limits Instlling Non-Customer Instllle Produts Instlling or Updting HP Open DeskMnger 3-1 Instlling HP ALLBASE/4GL 3-2 To instll new HP ALLBASE/4GL systems 3-2 To instll the HP ALLBASE/4GL environment 3-3 Instlling SNA IMF/XL 3-3 Instlling HP Preditive Support 3-4 Instlling NewWve Oe Produts 3-4 To instll HP Resoure Shring 3-4 To instll HP Informtion Aess Reovering Your System Using the HP Ftory Prelod Tpe (FTP) Determining System Reovery Using the HP FPT 4-1 Reovering Ftory Supplied Softwre nd I/O Congurtions 4-1 Prepring Your System for Reovery 4-2 To instll with the HP FPT 4-4 To omplete the reovery using the HP FPT 4-6 Completing Finl Reovery Tsks 4-9 A Congnme Tle Index Contents-1

10 Tles A-1 Congnme Tle A-1 Contents-2

11 1 Overview This mnul ontins proedures to oot, ongure nd strt up your new operting system for the HP 3000 Series 990 nd 992 Your system omes from the ftory with the fundmentl operting softwre (FOS), system les, nd purhsed produts pre-instlled A ftory prelod tpe (FPT) ontining the softwre tht ws instlled on your system is lso supplied If you re not le to omplete ll the proedures desried in hpter 2, \Strting your System," it my e neessry to perform reovery of your system softwre using the FPT This reovery proess should e only performed y your Hewlett-Pkrd representtive or y trined System Mngement personnel Instrutions for reovering the ftory preloded softwre re in hpter 4, \Reovering your System" Mterils Needed to Complete Instlltion This hpter ontins informtion on resoures you my need to omplete your instlltion Plese red the prgrphs elow nd ensure tht you hve the mnuls you need efore you egin For dditionl in-depth informtion on system tivity, system strtup funtions, nd the system genertor (SYSGEN), plese hve the following mnul ville for referene System Strtup,Congurtion, nd Shutdown Referene Mnul ( ) You my need to ongure dditionl disks on your system This is done using the VOLUTIL utility If you need dditionl informtion on this utility, plese ensure tht you hve the following mnul ville Volume Mngement Referene Mnul ( ) For dditionl informtion on reviewing ounts nd heking for psswords, guidelines on pssword formts, nd other seurity informtion, plese hve the following mnul ville for referene Mnger's Guide to MPE/iX Seurityl ( ) DTS (Terminl I/O) Ensure tht you hve the mnul listed elow ville for referene efore you ontinue You my need to refer to it lter in this mnul The hpter on onguring sysems for host-sed nd PC-sed mngement gives you NMMGR informtion on onguring terminl devies Conguring Systems for Terminls, Printers, nd Other Seril Devies ( ) The mnul elow gives you dditionl informtion on DTCs nd PC-sed network mngement Overview 1-1

12 DTC Network Plnning nd Congurtion Guide (D ) Additionl produts You my hve purhsed some produts tht were instlled t the ftory, ut need dditionl steps to mke them fully funtionl These produts require mnul steps to omplete the instlltion If you hve purhsed ny of the produts listed elow, plese red this setion efore you ontinue The NS3000/XL produt If you hve purhsed the NS3000/XL produt, plese ensure tht you hve the following mnuls ville efore you ontinue These mnuls provide you with informtion on onguring the links, trnsport, nd DTCs on the system Using the OpenView DTC Mnger Mnul (D ) The following mnul provides detils on NMMGR Using Node Mngement Servies (NMS) Utilities ( ) NewWve Offie/XL produts The NewWve Oe/XL produts inlude the produts listed elow If you re instlling ny of these produts, the following prgrphs ontin informtion you need efore you ontinue HP Open DeskMnger If you hve purhsed HP Open DeskMnger, plese ensure tht you hve these mnuls ville for referene HP Open DeskMnger Administrtion (B ) HP OPen DeskMnger User Referene Guide (B ) HP Resoure Shring HP Resoure Shring requires tht informtion from the NewWve Oe softwre ertite, inluding liense ode, e reorded on the system efore onnetions to shred servies re llowed If you re instlling HP Resoure Shring for the rst time, or updting your liense informtion, plese lote your NewWve Oe softwre ertite If you do not hve NewWve Oe softwre ertite, plese ontt your Hewlett-Pkrd representtive to otin temporry liense ode nd initite replement of your softwre ertite The NewWve Oe Resoure Shring for MPE XL Mnul ( ) provides informtion on instlling either the softwre ertite informtion or temporry liense ode t the pproprite point in the instlltion proess If you hve lredy reorded the informtion from the softwre ertite in previous instlltion or updte, nd your liense informtion hs not hnged, you do not need to reord the softwre ertite informtion gin HP Informtion Aess If you re instlling HP Informtion Aess, plese ensure tht you hve the following mnul ville You will referene this mnul during the mnul instlltion of HP Informtion Aess 1-2 Overview

13 Informtion Aess Server: System Mngement Mnul (B ) HP ALLBASE/4GL If you hve purhsed the HP ALLBASE/4GL developer system, plese ensure tht you hve the following mnul ville for referene HP ALLBASE/4GL Developer Administrtion Mnul ( ) If you hve purhsed n HP ALLBASE/4GL run-time system, plese ensure tht you hve the following mnul ville for referene HP ALLBASE/4GL Run-Time Administrtion Mnul ( ) Overview 1-3

14

15 2 Strting the System This setion desries the steps neessry to oot nd ongure, dd externl disks, nd omplete the instlltion of ny mnully instlled produts d Booting the System 1 Turn the system on After 5 to 10 minutes of system tivity, you should see sreen similr to the following PDC - Proessor Dependent Code Version nnn () Copyright The Hewlett-Pkrd Compny All rights reserved Totl Memory: Totl Proessors: MB Primry oot pth 0/ mens BC 0 in PMB slot 0 52 mens I/O rd in HP-PB slot 13 0 mens devie ID of 0 Alternte Boot Pth: 0/ Console/Keyord Pth: 0/ Strting the System 2-1

16 d Respond to the prompts s shown Continue with primry oot pth ([y]/n/<pth>) > Y Trying oot pth 0/ Booting Intert with ISL (Y or N)?> Y MMSAVE Version nnn DUMPAREA found, sve min memory to dis ISL loded ISL Revision vuu Month Dy, Yer ISL> If the ove sreen does not pper within 1 to 2 minutes, reset your system Press the 4CTRL5 nd B keys t the sme time When you see the CM prompt, onnet to the servie proessor, nd restrt system s shown elow Do not respond to \Press ny key within ten seonds to nel oot with this ongurtion" d 4CTRL5 B CM>SP SP>RS Type Y to onfirm your intention to exeute this ommnd (y/n): Y The system will restrt nd disply the Proessor Dependent Code (PDC) sreen shown in step 1 Note The following step pplies to ll systems exept the 9X8LX nd 9X8RS series If you hve 9X8LX or 9X8RX, refer to steps 2 nd 2 2 Run IOMAP nd print or reord the I/O ongurtion for your system Ensure tht ll peripherls re powered on efore you run IOMAP This disply shows ll the pth nmes of the I/O omponents These pth nmes will e dded to the SYSGEN I/O ongurtion ISL> IOMAP After severl progress messges you see the IOMAP nner Reply N to \Do you wish to modify ny progrm prmeters? [y,n] (n):" 2-2 Strting the System

17 Identify: Loop 1: All I/O omponents re eing Proessor Identifition: Type HW SW Revisions Tests Pth Component Nmes ID Mod Mod Hdwr Firm Avil Bus Converter (Lol Port) 7H 184H CH /0 HP-PB GPIO Crd 4H 4H 45H /4 HP-PB SCSI Crd 4H 4H 39H 0 0 ST LB Resetting SCSI Bus (Approx 10 seonds) SCSI us ddress for host dpter is 7 16/440 HPC1512A DDS tpe drive C600 ST 16/450 HPC1503A/HPC15208 DDS tpe drive ST 16/5 HP-PB Centronis Prllel Port 5H 4H 3AH / LAN 2H 4H 52H 0 0 ST LB 16/36 HP-PB HPFL Crd 4H 4H 41H 0 0 ST 16/ FL dis drive ST 16/ FL dis drive ST 16/ HA FL dis drive ST 16/44 HP-PB Console/LAN Crd 2H 54H 50H 0 0 ST LB System Console is onneted to this rd 16/52 CIO Chnnel Adpter 8H 5H 10H 0 0 ST LB 16/520 HP-IB rd 2H ST LB 16/ mg tpe unit 180H /50 Bus Converter (Remote Port) 1H 7H 102H CH Bus Converter (Lol Port) 7H 184H CH Memory Controller ( 511 M ytes) 1H 5H 9H 1 0 LB 40 Memory Controller ( 0 M ytes) 1H 5H 9H 1 0 LB 48 Ntive Proessor 0H 56 Ntive Proessor 0H Identify loop 1 (1H) omplete Do you wnt to exit this progrm nd return to ISL? [y,n] (n): Y IOMAP Exiting Swithing the Console k to the stndrd Console Pth Done ISL> Strting the System 2-3

18 For 9X8LS nd 9X8RX systems, use the following proedure to list your system hrdwre: i Type the following t the ISL prompt to get n ODE prompt: ISL> ODE ii Type the following t the ODE prompt to get MAPPER prompt: ODE> MAPPER iii At the MAPPER prompt type: MAPPER> RUN To exit MAPPER fter you modify or ept the informtion displyed, you must exit out of MAPPER nd ODE to get k to the ISL prompt For exmple: MAPPER> EXIT ODE> EXIT ISL> 3 Strt the system from the disk The ongurtion for your system ws preloded t the ftory nd is ongured for the numer of internl disks tht you purhsed with your system ISL> START NORECOVERY d The system displys series of strtup messges, nd you re prompted to onrm the dte nd time, s shown elow If the dte nd time displyed re urte, enter Y If not, enter N, nd enter the orret dte nd time when prompted Time must e entered in 24-hour formt (eg, 5:00 pm is entered s 17:00) Seonds defult to 00 if not speied MPE/iX lunh fility Initilize_genesis - Version ; nnnnnnnnnn TUE, AUG 11, 1991, 10:20:03 AM (y/n)? Y or N [CMUX_DAM] nnnn Initilize genesis ompleted For the next 5-6 minutes, strtup nd initiliztion messges re displyed similr to the sreen shown elow 2-4 Strting the System

19 d Initilize genesis ompleted Crete Console Messges kso ompleted Initilize memory mnger ompleted SESSION Sheduling Initilized Initite Opertor Logon JOB Sheduling Initilized Suessfully lunhed dignosti monitor proess 4 Log on to the system :HELLO MANAGERSYS :STREAMS strems devie :SPOOLER LP;START 5 A defult ongurtion with the internl disks ongured ws loded onto your system t the ftory If you hve ny externl disks, or other devies, you must hnge this defult ongurton to inlude these omponents Use SYSGEN to ongure them into your system If you need dditionl informtion on the SYSGEN utility, plese refer to System Strtup, Congurtion, nd Shutdown Referene Mnul ( ) If you do not hve ny externl disks, or other devies, ontinue with \Conguring System Disks Using VOLUTIL"; otherwise follow the steps elow :SYSGEN sysgen>io 6 Print the defult ongurtion to the sreen nd reord the ongurtion This ongurtion should e hnged to represent the tul ongurtion s shown on IOMAP io>lp 7 Using the ommnds in io, mke ny hnges to your ongurtion After you hve ompleted the ongurtion hnges, hold the new ongurtion nd exit: io>hold io>exit 8 Sve this new ongurtion sysgen>keep CONFIG Purge old onfig? YES sysgen>e 9 Shut down the system y pressing the 4CTRL5 nd A keys t the sme time, then typing SHUTDOWN s follows: 4CTRL5 A =SHUTDOWN Strting the System 2-5

20 d Shutdown of user proess egins (Shut 1) Shutdown of user proess egins (Shut 2) Shutdown of operting system omplete (Shut 6) There will e severl shutdown messges similr to those shown ove 10 After the lst shutdown messge, (Shut 6), restrt the system y pressing the 4CTRL5 nd Bkeys t the sme time Respond to the prompts s shown You must onnet to the servie proessor efore you n restrt the system 4CTRL5 CM>SP SP>RS B d Type Y to onfirm your intention to exeute this ommnd (y/n): Y Do not respond to \Press ny key within 10 seonds to nel oot with this ongurtion" If the system does not respond to the 4CTRL5 B within ten seonds power the system o nd then k on gin, nd repet step 9 11 Conrm tht you wnt to ontinue the oot from the primry oot pth Reply Y to \Intert with ISL?" 12 Strt the system from the disk t the ISL> prompt ISL>START NORECOVERY 13 Log on to your system :HELLO MANAGERSYS;HIPRI :STREAMS strems devie :SPOOLER LP;START A welome messge ppers After the welome messge, you see the session prompt (:) 2-6 Strting the System

21 Configuring System Disks Using VOLUTIL If you hve dditionl disks on your system, use the VOLUTIL utility to dene nd initilize them 1 Chek the sttus of the disks :DSTAT ALL 2 If your disks re not in Mster or Memer sttus, use the following VOLUTIL ommnds to hnge the sttus :VOLUTIL VOLUTIL:SCRATCHVOL n *Verify: Srth volume on ldev n [Y/N]? Y VOLUTIL:NEWVOL MPEXL_SYSTEM_VOLUME_SET:MEMBERn n DISC *Verify: Initilize new memer volume Memern on ldev n? Y VOLUTIL:EXIT The n in the ove ommnds refers to the ddress of the disk you re dding to your system Repet these ommnds to dd dditionl disks to your system Reple n with the ddress of the dditionl disk(s) 3 When you hve ongured ll disks onto your system, enter the DSTAT ALL ommnd gin to ensure the disks re mounted :DSTAT ALL Instlling Additionl Produts There re severl Hewlett-Pkrd produts tht require dditionl steps efore they re fully instlled These produts nd their instlltion instrutions re loted in hpter 3, \Instlling/Conguring Additionl Produts" The softwre for these produts is pre-loded onto the internl disk when your system omes from the ftory; however, dditionl instlltion steps re needed for some produts efore they re fully funtionl Use the following steps to determine whether you hve purhsed ny of these produts 1 If you re not logged on s MANAGERSYS, log on s follows: :HELLO MANAGERSYS 2 Enter the LISTF ommnd to determine if the le SPNAMES exists on your system :LISTF SPNAMESPUBSYS Strting the System 2-7

22 If no le is found, you hve not purhsed ny of these produts Continue with \Conguring Dt Communition," on the following pge 3 If the SPNAMES le is found, enter the following ommnd to disply the ontents of the le to the sreen :PRINT SPNAMESPUBSYS 4 Reord the nmes of the produts listed on the lines elow These produts require dditionl steps to e performed efore they re fully funtionl If you purhsed NS3000/XL produts (eg, NS/XL NetWork Servies) there re no dditionl mnul steps required Refer to hpter 3, \Instlling Non-Customer Instllle Produts" for instrutions to omplete your instlltion When you hve ompleted the instlltion of these produts, ontinue with \Conguring Dt Communition" elow Note If you purhsed the NewWve Oe produts, HP Resoure Shring or HP Informtion Aess, you must ongure your dtomm efore you n instll these produts Continue with \Conguring Dt Communition" You will e referred to hpter 3 to omplete the instlltion of these produts Configuring Dt Communition You must ongure your dt ommunition euse the informtion is used y the dt ommunition terminl ontroller(s) (DTC) to llow terminl ommunition 1 Log on nd nd rete new le from the smple le NMSAMP1PUBSYS Follow the steps elow :HELLO MANAGERSYS :FILE CONFIG=NMCONFIGPUBSYS;DEV=1 :FCOPY FROM=NMSAMP1PUBSYS;TO=*CONFIG;NEW 2 Use NMMGR to modify the DTS ongurtion in NMCONFIG Note NMSAMP1 does not ontin vlue in the physil pth eld of the DTSLINK sreen When you re in NMMGR, enter the vlue 56 in the physil pth eld You must lso supply the lol node nme If you hve PC-sed network mngement, ongure the DTC(s) following the instlltion nd ongurtion proedures desried in the Using the OpenView DTC Mnger Mnul (D ) For more informtion on host-sed network mngement, refer to the Conguring Systems for Terminls, Printers nd Other Seril Devies Mnul ( ) For more informtion on NMMGR, refer to Using Node Mngement Servies (NMS) Utilities ( ) If you hve purhsed the MPE/iX NS produt, use the \guided ongurtion" within NMMGR to ongure NS You must lso use NMMGR to vlidte the DTS ongurtion 2-8 Strting the System

23 d nd the MPE/iX NS produt (if it is on your system) When you hve ompleted the vlidtion in NMMGR, exit the progrm :NMMGR After you hve mde your hnges to the dtomm ongurtion, NMMGR utomtilly runs SYSGEN to ross vlidte the system nd dtomm ongurtion You n then exit NMMGR 3 Shut down the system 4CTRL5 A =SHUTDOWN Shutdown of user proess egins (Shut 1) Shutdown of user proess egins (Shut 2) Shutdown of operting system omplete (Shut 6) There will e severl shutdown messges similr to those shown ove 4 After the lst shutdown messge, (Shut 6), restrt the system y pressing the 4CTRL5 nd B keys t the sme time Respond to the prompts s shown You must onnet to the servie proessor efore you n restrt the system 4CTRL5 CM>SP SP>RS B d Type Y to onfirm your intention to exeute this ommnd (y/n): Y Do not respond to \Press ny key within 10 seonds to nel oot with this ongurtion" If the system does not respond to the 4CTRL5 B within ten seonds power the system o nd then k on gin, nd repet step 5 5 Conrm tht you wnt to oot the system from the primry pth Strting the System 2-9

24 d Continue with primry oot pth ([y]/n/<pth>) >Y Trying oot pth 0/ Booting Intert with ISL (Y or N)?> Y MMSAVE Version nnn DUMPAREA found, sve min memory ot dis ISL loded ISL Revision vuu Month Dy, Yer ISL> When the system is up, power yle ll DTCs, or perform reset using TERMDSM in SYSDIAG (you only need to do this for host-sed DTCs) Strt the system from the disk: ISL>START NORECOVERY Note Reooting the system enles the vlidted dtomm ongurtion to tke eet on the system Power yling eh DTC enles the new downlod le nd the DTC ongurtions to e downloded to the DTCs The DTCs will not work if this step is not ompleted The system displys series of strtup messges, nd you re prompted to onrm the dte nd time, s shown elow If the dte nd time displyed re urte, respond Y If not, respond N, nd enter the orret dte nd time when prompted Time must e entered in 24-hour formt (eg, 5:00 pm is entered s 17:00) Seonds defult to 00 if not speied d MPE/iX lunh fility Initilize_genesis - Version ; nnnnnnnnnn TUE, AUG 11, 1993, 10:20:03 AM (y/n)? [CMUX_DAM] nnnn Initilize genesis ompleted Y/N 2-10 Strting the System

25 d For the next 5-6 minutes, strtup nd initiliztion messges re displyed similr to the sreen shown elow Initilize genesis ompleted Crete Console Messges kso ompleted Initilize memory mnger ompleted SESSION Sheduling Initilized Initite Opertor Logon JOB Sheduling Initilized Suessfully lunhed dignosti monitor proess Note NS3000/XL now inludes informtion les tht desrie the supported set of servers nd servies These informtion les re used to uild ongurtion le lled DADCONFNETSYS Be sure to perform the following steps Wit until the jostrem is omplete efore strting step 7 elow :HELLO MANAGERSYS; HIPRI :SPOOLER LP;START :STREAMS strems devie :LIMIT 1,1 :STREAM JCONFJOBNETSYS Note If you hve the NewWve Oe produts, HP Resoure Shring or HP Informtion Aess, plese go to hpter 3 to omplete your instlltion or updte After you hve ompleted the instrutions in hpter 3, ontinue with step 7 elow 6 If you hve NS3000/XL ongured, ring up the ongured network interfes Be sure to use the sme nmes for the network interfes tht were used in the ongurtion For exmple, if you hve ongured network interfes with the nmes LOOP nd LAN1, enter: :NETCONTROL START;NET=LOOP :NETCONRTOL START;NET=LAN1 :NSCONTROL START If you hve ongured only the router network interfe with the nme ROUTER1, enter: :NETCONTROL START;NET=ROUTER1 :NSCONTROL START Strting the System 2-11

26 Setting Psswords 1 Use the following ommnds to ssign psswords to the ount SYS, user MANAGER, nd group PUB for MANAGERSYS,PUB :ALTACCT SYS;PASS=pssword :ALTUSER MANAGER;PASS=pssword;HOME=homegroup :ALTGROUP PUB;PASS=pssword 2 Hewlett-Pkrd lso reommends tht you set psswords for the following ounts nd users These ounts nd users re urrently reted nd/or modied during the instlltion proess, regrdless of the type of produts on the SUBSYS tpe You my nd tht some of these ounts do not ontin les fter you omplete the instlltion CONV CLL HPOFFICE HPPL85 HPPL87 HPPL89 INDHPE ITF3000 RJE SUPPORT TELESUP SNADS SYSMGR HPOPTMGT HPSKTS HPNCS NETWARE SYS HPLANMGR HPX11 The following users re reted nd/or modied to hve OP nd/or PM or SM pilities Hewlett-Pkrd reommends tht you set psswords for these users MANAGERSYS MGRHPOFFICE FIELDHPPL85 MGRTELESUP 2-12 Strting the System

27 MGRSNADS MGRSYSMGR Reord the psswords nd keep them in seure ple If you wish dditionl informtion on system seurity, plese onsult the Mnger's Guide to MPE/iX Seurity ( ) Creting Bkup Tpe Before you egin norml opertions, it is importnt tht you k up your new system The kup ommnd le shown elow lls n indiret le whih will k up your omplete system on one tpe If you wnt informtion on the ontents of this le, plese refer to hpter 4, \Reovering your System" Follow the steps elow to k up your system 1 If you re not logged on s MANAGERSYS, do so now :HELLO MANAGERSYS 2 Use the SYSGEN utility to rete your reovery tpe :SYSGEN 3 Lod lnk red-write ssette tpe into the DDS tpe drive Ensure tht the tpe is write-enled tpe Wit until the tpe is fully loded efore you ontinue (oth lights on the DDS drive re lit) sysgen> TAPE STORE=^FSETLIST 4 Reply to the tpe request t the system onsole 5 This proess n tke uptotwo hours, depending on the numer of les you hve onyour system A listing of the les tht re stored iswritten to spoolle, OnnOUTHPSPOOL If you hve printer, this listing will e printed in ddition to eing written to the spoolle When the reovery tpe hs ompleted, return to the session prompt (:) sysgen> EXIT 6 Move the ssette t to red only mode Lel the tpe nd store it with listing of your kup les Setting Jo nd Session Limits Set jo nd session limits to llow users nd jos to log on Sustitute pproprite vlues for n nd nn The rst vlue sets the mximum numer of jos; the seond vlue sets the mximum numer of sessions :LIMIT n,nn Your system is redy for norml prodution Reord this instlltion in the system logook Strting the System 2-13

28

29 3 Instlling Non-Customer Instllle Produts The following produts need dditionl steps to e performed efore they re fully funtionl Your Hewlett-Pkrd Customer Engineer will omplete the instlltion of these produts for you Plese ontt him for ssistne Instlling or Updting HP Open DeskMnger The HP Open DeskMnger softwre is now instlled on your system; however, efore ttempting to use the produt, there re some steps tht must e ompleted If you re instlling HP Open DeskMnger for the rst time, you must rete nd ongure your dtses Refer to hpters 8 nd 9 of the HP DeskMnger Administrtion mnul (B ) for detils on how to do this The following UDC les re supplied with HP Open DeskMnger: OPERUDCMAILLIBHPOFFICE - this holds the opertor ommnds MAILUDCMAILLIBHPOFFICE - this holds the user ommnds The level t whih these UDCs re set depends upon the guidelines followed t your site; however, Hewlett-Pkrd reommends setting the opertor ommnds t the user level for the user MGRHPOFFICE To do this, enter the following ommnds: :HELLO MGRHPOFFICE,MAILLIB :SETCATALOG OPERUDCMAILLIBHPOFFICE Rememer to inlude ll other UDCs tht re to e set t the sme level in the SETCATALOG ommnd The following seven items my pply to your system Plese red them nd follow the instrutions, if they re pplile The Amerin version of the produt is supplied s defult, however, if British version is to e instlled, enter the following ommnd: :STREAM UKDICTMAILJOBHPOFFICE If you re running HP Open DeskMnger on stndlone system, nd Distriuted Systems (DS) or Network Servies (NS) re NOT instlled, enter the following ommnd: :STREAM DSNSSEGSMAILJOBHPOFFICE It is possile to improve the performne of HP Open DeskMnger y reting n Ojet Code Trnslted (OCT) version Red the le OCTINSTLMAILJOBHPOFFICE for detiled instrutions on how to perform this trnsltion If Lotus :Mil or Mirosoft Mil lients re to e used with HP Open DeskMnger, mnul djustment to the UALCONFGMAILCONFHPOFFICE ongurtion le is neessry Instlling Non-Customer Instllle Produts 3-1

30 Refer to hpter 2 in the HP Open DeskMnger Administrtion mnul (B ) for detils If the HP DeskNote text editor is to e used, mnul djustment my e required to the HP DeskNote glol ongurtion le to enle spell heking See hpter 2 in the HP Open DeskMnger Administrtion mnul (B ) for detils The Grge Colletor proess (if used) needs to e re-enled See hpter 2 in the HP Open DeskMnger Administrtion mnul (B ) fordetils If you re upgrding n existing version of HP DeskMnger, the old HP DeskMnger jo strem les will e overwritten during the instlltion proess If you hve ustomized ny of these jo strem les, you must re-pply your hnges to the new les DO NOT overwrite the new les with your old les For omplete list of these jo strem les, plese refer to hpter 2 of the HP Open DeskMnger Administrtion mnul (B ) Instlling HP ALLBASE/4GL To omplete the instlltion of HP ALLBASE/4GL some dditionl steps must e performed These instlltion proedures must e ompleted on terminl other thn the system onsole HP ALLBASE/4GL nnot e run on the system onsole To instll new HP ALLBASE/4GL systems To omplete the instlltion of the HP ALLBASE/4GL Developer system or the HP ALLBASE/4GL Run-Time Environment, perform the following steps fter the AUTOINST hs run 1 Crete the ount in whih you wnt to use HP ALLBASE/4GL You n selet ny nme for the ount, ut we suggest tht you use the nme HP4GL for the HP ALLBASE/4GL Developer System, nd HP4GLR for the HP ALLBASE/4GL Run-Time Environment Developer or Run-Time :HELLO MANAGERSYS :NEWACCT HP4GL,MGR;PASS=pssword;CAP=AM,AL,GL,ND,SF,BA,IA,PH :HELLO MANAGERSYS :NEWACCT HP4GLR,MGR;PASS=pssword;CAP=AM,AL,GL,ND,SF,BA,IA,PH 2 Log on to the new ount nd exeute the following ommnd le: Developer or :HELLO MGRHP4GL :HP4BLDHP4GLSYS 3-2 Instlling Non-Customer Instllle Produts

31 Run-Time :HELLO MGRHP4GLR :HP4BLDRHP4GLRSYS HP4BLD (or HP4BLDR) will rete severl groups within the ount After the groups re reted, the utility opies severl les from the SYS ount into the newly reted groups To instll the HP ALLBASE/4GL environment The defult HP ALLBASE/4GL instlltion ssumes tht the MPE/iX system is ongured to support the Amerin version s well s the \ntive omputer" lnguge To run HP ALLBASE/4GL on terminl tht supports the line-drwing hrter set, set the MPE/iX vrile HP4TERM s follows: :SETVAR HP4TERM "HPL" Refer to the HP ALLBASE/4GL Developer Administrtion Mnul ( ) or the HP ALLBASE/4GL Run-Time Administrtion Mnul ( ) for further informtion on setting up the HP ALLBASE/4GL environment HP ALLBASE/4GL is now redy to e run Instlling SNA IMF/XL You must perform some dditionl steps efore SNA IMF/XL (HP30293) is fully funtionl Follow the steps elow using the TTSINST ommnd le to omplete the instlltion You n lso ess the online instrutions y typing TTSINSTPUBSYS t the olon prompt without speifying ny prmeters To instll the English Lnguge Option for the United Sttes nd Europen sites, type the following ommnds: d :HELLO MANAGERSYS :TTSINST 000 Conrm tht you wnt to omplete the instlltion: SNA IMF> Begin instlling the English option (Y/N)? Y SNA IMF> The English lnguge option is now instlled To instll the Asin Lnguge Option, type the following ommnds: :HELLO MANAGERSYS :TTSINST Red the instrutions tht pper on your sreen, then enter the following: :TTSINST 221 ** 221 is the lnguge option prmeter ** Conrm tht you wnt to omplete the instlltion: Instlling Non-Customer Instllle Produts 3-3

32 d SNA IMF> Begin instlling the Jpnese option (Y/N)? Y SNA IMF> The Jpnese lnguge option is now instlled Instlling HP Preditive Support If this is the rst time you hve purhsed HP Preditive Support, your Hewlett-Pkrd Customer Engineer will ssist you with the instlltion nd supply you with the HP Preditive Support User's Guide ( ) Instlling NewWve Offie Produts NewWve Oe produts inlude HP Open DeskMnger, HP Resoure Shring, nd HP Informtion Aess Instrutions for instlling HP Informtion Aess nd HP Resoure Shring re listed elow Instrutions for instlling HP Open DeskMnger re listed in the eginning of this setion To instll HP Resoure Shring Cution If you ttempt to onnet PC to shred resoures efore you omplete the steps listed ove, you will hve to restrt the system nd perform these steps gin The messge \Resoure Shring Registrtion Completed" must pper on the onsole efore you n onnet PC to shred resoure 1 Liense informtion from the NewWve Oe Softwre Certite must e reorded on the system efore onnetions to shred resoures n e llowed You do not need to reord this informtion gin if you hve reorded it previously, nd it hs not hnged If you need to updte liense informtion, or re reording it for the rst time, plese refer to the \Instlltion" hpter in the NewWve Oe Resoure Shring for MPE XL Mnul ( ) The \Instlltion" hpter provides the instrutions for Reording Liense Informtion from the softwre ertite, with the NWOLCPPCSYS progrm 2 Strem JPDINSTLNWOCONFHPOFFICE to omplete the instlltion Wth for the onsole messge, \Resoure Shring Registrtion Completed" to verify tht HP Resoure Shring is redy to reeive onnetion requests from PCs 3 If you hve HP Informtion Aess, ontinue elow; otherwise, return to step 7, pge 2-11 To instll HP Informtion Aess Plese refer to the Informtion Aess Server: System Mngement Mnul (B ) for instlltion instrutions After you hve ompleted your HP Informtion Aess instlltion, plese return to step 7, pge Instlling Non-Customer Instllle Produts

33 Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4 The proedure desried in this hpter is not prt of the norml instlltion proess for strting your system Reovering your system using the ftory prelod tpe (FPT) should e performed only y system mngement trined personnel or Hewlett-Pkrd Servie Representtive This proedure my result in loss of user dt if it is performed inppropritely Determining System Reovery Using the HP FPT In the unlikely event tht your system does not oot when you turn it on, or does not respond to the 4CTRL5 B reset, it is neessry to onrm tht the system is onneted orretly nd is reeiving power If you hve onrmed tht the system is onneted orretly, nd the oot pth does not pper, you my need to use the ftory prelod tpe (FPT) to reover your system Reovering Ftory Supplied Softwre nd I/O Configurtions If your Hewlett Pkrd supplied softwre ws ftory loded onto your system, tpe ontining opy of the softwre ws lso supplied with your system This tpe, referred to s ftory prelod tpe (FPT), provides you with omplete system kup prior to eginning the instlltion proess This tpe hs een ustomized to your order nd ontins system les, store les, nd defult ongurtion les One of the nl instlltion steps provided in this hpter is to generte system reovery tpe reeting hnges resulting from the instlltion nd ongurtion proess Whenever possile, this newly generted reovery tpe should e used in ple of the ftory prelod tpe (FPT) for reovery purposes This hpter desries the steps neessry to reover the HP 3000 Series 990 or 992 system using the FPT This entire proess tkes pproximtely 2 to 3 hours, depending on the numer of softwre pplitions to e instlled Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4-1

34 Prepring Your System for Reovery 1 Power on the system 2 Insert the FPT for this system into the DDS devie Ensure tht the ssette is red-only tpe (The t on the right red edge should e pushed to the left of the ssette so the reognition hole is open) The lod sequene is nished when the ssette light remins on 3 Press the 4CTRL5 nd B keys t the sme time You will see CM> prompt on your sreen Connet to the servie proessor nd restrt the system CM>SP SP>RS d Type Y to onfirm your intention to exeute this ommnd (y/n): Y Do not respond to \Press ny key within 10 seonds to nel oot with this ongurtion" If the system does not respond within ten seonds power, the system o nd then k on gin 4 After the onsole sreen displys 5 to 10 minutes of restrt messges, the system displys sreen similr to the following Respond N to \Continue with primry oot pth?" prompt 4-2 Reovering Your System Using the HP Ftory Prelod Tpe (FTP)

35 d PDC - Proessor Dependent Code Version nnn () Copyright The Hewlett-Pkrd Compny All rights reserved Totl Memory: Totl Proessors: MB Primry oot pth 0/ mens BC 0 in PMB slot 0 52 mens I/O rd in HP-PB slot 13 0 mens devie ID of 0 Alternte Boot Pth: 0/ Console/Keyord Pth: 4/ Continue with primry oot pth? ([y]/n/<pth>) > N 5 A Min ommnd menu ppers on your sreen Enter B to disply the Boot menu Enter A to oot from the lternte oot pth Conrm tht you wnt to ontinue ooting from the lternte oot pth Enter Y to \Intert with ISL?" d Continue with lternte oot pth? ([y]/n/<pth>) > Y Booting Intert with ISL (Y or N)?> Y ISL Revision vuu Month Dy, Yer ISL> After responding Y to the previous questions, the system oots from the FPT After the system hs ompleted the loding proess, the ISL> prompt is displyed Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4-3

36 To instll with the HP FPT 1 Enter the INSTALL ommnd to instll the HP 3000 Series 990 or 992 with the FPT ISL>INSTALL d While the instlltion proess is tking ple, it is importnt tht you monitor the proess t the onsole Note ny errors tht my e reported to the sreen for future tion 2 Following some tpe tivity (up to 3 minutes), you re prompted to onrm the dte nd time, s shown in the following sreen If the dte nd time displyed re urte, respond Y; if no, respond N, nd enter the orret dte nd time when prompted Time must e entered in 24-hour formt (For exmple, 5:00 pm is entered s 17:00) Seonds defult to 00 if not speied MPE/iX lunh fility INSTALL xnnnn Copyright () Hewlett-Pkrd 1987 INSTALL -- MPE-XL dis imge uilder -- version 10 Initilize_genesis - Version: nnnnnnnnnn TUE, FEB , 10:20:03 AM (y/n)? Y/N [CDM] nnnn Initilize memory mnger ompleted Beginning INSTALL 4-4 Reovering Your System Using the HP Ftory Prelod Tpe (FTP)

37 d It tkes 10 to 20 minutes to restore the les from the FPT During this time, the system displys initiliztion nd restore messges Do not respond to \Press ny key within 10 seonds to nel oot with this ongurtion" END of LOAD(instll) Auto oot in progress Continue with primry oot pth? ([y]/n/<pth>) > Y Trying oot pth 0/ Booting Intert with ISL? (y/[n])> Y MMSAVE Version nnn DUMPAREA found, sve min memory to dis ISL loded ISL Revision vuu Month Dy, Yer ISL> 3 One the system reoots, you will see the ISL> prompt Strt the system from the disk, using the ongurtion nme tht is most pproprite for your system Plese onsult ppendix A for listing of the ville smple ongurtions ISL>START NORECOVERY;GROUP=ongnme 4 The system displys series of strtup messges, nd you re gin prompted to onrm the dte nd time If you do not respond Y or N within 15 seonds, the system ssumes the displyed dte nd time y defult nd ontinues with the strtup If the dte nd time displyed re urte, respond Y If not, respond N nd enter the orret dte nd time Time must e entered in 24-hour formt (For exmple, 5:00 pm is entered s 17:00 Seonds defult to 00 if not speied) Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4-5

38 d MPE/XL lunh fility Initilize_genesis - Version: nnnnnnnnnn TUE, FEB 12, 1991, 10:20:03 AM (y/n)? Y/N [TMUX_CDM] n n n n Initilize genesis ompleted d For the next few minutes, strtup nd initiliztion messges re displyed, similr to the sreen shown elow: Initilize genesis ompleted Crete Console Messges ompleted Initilize memory mnger ompleted Initilize resident kernel ompleted Protetion of system files hs een ompleted SESSION Sheduling Initilized Initite Opertor Logon JOB Sheduling Initilized Suessfully lunhed dignosti monitor proess To omplete the reovery using the HP FPT 1 When the reovery proess is omplete, log on to the onsole nd strt the spooler nd strems devie :HELLO MANAGERSYS,INSTALL;HIPRI :SPOOLER LP;START :STREAMS strems devie Note During the log on to the INSTALL group, you my see the following messge: WARNING: GROUP OUT OF CONNECT TIME (CCIWARD 1494) You n ignore this messge, it does not et your instll proess 4-6 Reovering Your System Using the HP Ftory Prelod Tpe (FTP)

39 2 Run SYSGEN nd keep the oot ongurtion s follows: :SYSGEN sysgen> KEEP CONFIG Purge old onfigurtion (yes/no)? Y Keep onfigurtion nywy (yes/no)? Y sysgen> EXIT 3 If you purhsed dditionl disks, you my need to dd them to your system Run DSTAT to hek the sttus of the volume disks on your system :DSTAT ALL 4 If your volumes re not in Mster or Memer sttus, use the following VOLUTIL ommnds to hnge the sttus of the volume disks to Mster or Memer :VOLUTIL VOLUTIL:SCRATCHVOL n *Verify: Srth volume on ldev n [Y/N]? Y VOLUTIL:NEWVOL MPEXL_SYSTEM_VOLUME_SET:MEMBERn n DISC *Verify:Initilize new memer volume MEMBERn on ldev n?y VOLUTIL:EXIT The n in the ove ommnds refers to the ddress of the disk you re dding to your system Repet these ommnds to dd dditionl disks to your system Reple n with the ddress of the dditionl disk(s) 5 When you hve ompleted dding the volumes to your system, run DSTAT gin to ensure tht ll volumes hve een mounted 6 Remove the ssette from the tpe drive nd then re-insert it into the sme DDS devie in order for the ssette to rewind Wit for the drive to lod the ssette nd perform short lod sequene The lod sequene is omplete nd the ssette is online when the ssette light is on 7 At the system prompt, run HPINSTAL to updte the system with the new FPT Be sure to use the INFO prmeter RECOVERY when you enter the following ommnd :RUN HPINSTALINSTALL;INFO="RECOVERY" Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4-7

40 d MPE/XL HPINSTAL xnnnn (C) HEWLETT-PACKARD CO Mount the CSLT nd put the tpe/dds drive online the HP-supported softwre files will e restored *****Plese stnd y ***** The HP-supported softwre files re eing restored Note tht the FPT is represented y the term CSLT on the onsole sreen d 8 Reply to the tpe request y pressing 4CTRL5 nd A to get the = prompt The reply should inlude oth the PIN numer nd the LDEV numer of the tpe drive? /#Snn/nnn/LDEV# "SLTSTORE" ON TAPE(NUM)? =REPLY nnn,ldev# d No dditionl input is required The HPINSTAL utility restores the progrm/dt les from the Store omponent of the FPT, strems SUPACCT to rete the pproprite ount struture, nd strems instlltion les (if ny) When these proesses re omplete, HPINSTAL lists ny susystem produts tht require dditionl mnul steps to omplete the instlltion The sreen you see is similr to the following: *WARNING -- This progrm nnot instll the produts listed elow (INSTWARN #1) produt nme produt nme These produt nmes re written to le you will use when you ring the system up in hpter 2 When the HPINSTAL proess is ompleted, you see the following messge on the sreen 4-8 Reovering Your System Using the HP Ftory Prelod Tpe (FTP)

41 d The instlltion is now omplete END OF PROGRAM Completing Finl Reovery Tsks When the instlltion hs suessfully ompleted, you must perform severl mnul steps efore your system is returned to the ftory prelod ondition 1 Purge the spoolles tht HPINSTAL reted y entering the following ommnd t the prompt: 2 Purge the INSTALL group from your system y typing the following ommnds nd responding Y to the system question to purge the group :CHGROUP PUB :PURGEGROUP INSTALL 3 Crete n indiret le to provide single-tpe kup proedure for the system :EDITOR \A 2 // \K FSETLIST \EXIT 4 Crete new user, OPERATORSYS, nd OPERATOR UDC: :NEWUSER OPERATORSYS;HOME=PUB;CAP=IA,BA,OP,PH,SF,ND :SETCATALOG HPOPUDCMPEXLSYS;USER=OPERATORSYS 5 Shut down the system 4CTRL5 A =SHUTDOWN You hve ompleted the reovery of your system It is now identil to the system tht ws shipped from the ftory Remove the FPT nd store it in sfe ple You re now redy to prepre the system for use Reovering Your System Using the HP Ftory Prelod Tpe (FTP) 4-9

42 If you hve red the informtion ontined in hpter 1, \Overview," proeed to hpter 2, \Strting the System" nd follow the steps to prepre your system for use 4-10 Reovering Your System Using the HP Ftory Prelod Tpe (FTP)

43 A Confignme Tle Tle A-1 Confignme Tle SYSTEM HP-IB Group HP-FL (Alink) Group Series 990 CONFG990 ALINK990 Series 992/100 CONFG992 Series 992/200 CONFG992 Series 992/300 CONFG992 Series 992/400 CONFG992 ALINK992 ALINK992 ALINK992 ALINK992 Confignme Tle A-1

44

45 Index A ounts setting psswords, 2-12 dditionl instlltion steps, 2-7 dditionl produts instlling, 2-7 Amerin version HP ALLBASE/4GL, 3-3 HP DeskMnger, 3-1 Asin lnguge option SNA IMF/XL, 3-3 B kup tpe reting, 2-13 ooting the system, 2-1 primry pth, 2-6 reovery, 4-2 British version HP DeskMnger, 3-1 C omponent nmes, 2-2 ongurtion hold, 2-5 sve, 2-5 ongurtion le NS3000/XL, 2-11 onguring dt ommunition, 2-8 onguring dtses HP DeskMnger, 3-1 onguring system disks VOLUTIL, 2-7, 4-7 reting kup tpe, 2-13 ross vlidtion SYSGEN, 2-9 D dt ommunition onguring, 2-8 dt ommunition terminl, DTC, 2-8 DTC power yling, 2-10 DTS ongurtion NMMGR, 2-8 E English lnguge option SNA IMF/XL, 3-3 externl disks ongurtion, 2-5 F ftory prelod tpe, 4-1 ftory prelod tpe (FPT) ontents, 4-1 nl reovery tsks reting n indiret le, 4-9 reting OPERATORSYS, 4-9 deleting spoolles, 4-9 purging INSTALL group, 4-9 shutting down the system, 4-9 FPT ompleting nl reovery, 4-9 reovering your system, 4-1 G guided ongurtion NMMGR, 2-8 H host-sed network mngement, 2-8 HP ALLBASE/4GL Amerin version, 3-3 instlling, 3-2 instlling developer system, 3-2 instlling run-time environment, 3-2 line-drwing hrter set, 3-3 ntive omputer lnguge, 3-3 HP DeskMnger Amerin version, 3-1 British version, 3-1 onguring dtses, 3-1 instlling, 3-1 Ojet Code Trnslted version, 3-2 stndlone, 3-1 UDC les, 3-1 HP Informtion Aess, 2-8 Index-1

46 instlling, 3-4 NewWve, 3-4 HPINSTAL reovery, 4-7 HP Preditive Support, 3-4 HP Resoure Shring, 2-8 instlling, 3-4 NewWve, 3-4 I indiret le reting, 4-9 informtion les NS3000/XL, 2-11 Initil Progrm Lod, 2-2 INSTALL group purging, 4-9 instlling dditionl produts, 2-7 HP ALLBASE/4GL, 3-2 HP DeskMnger, 3-1 HP Informtion Aess, 3-4 HP Resoure Shring, 3-4 NewWve, 3-4 SNA IMF/XL, 3-3 instlling developer system HP ALLBASE/4GL, 3-2 instlling run-time environment HP ALLBASE/4GL, 3-2 instlling with the FPT, 4-4 IOMAP system ongurtion, 2-5 L line-drwing hrter set HP ALLBASE/4GL, 3-3 logging on reovery, 4-6 N ntive omputer lnguge HP ALLBASE/4GL, 3-3 NewWve HP Informtion Aess, 3-4 HP Resoure Shring, 3-4 instlling, 3-4 NewWve Oe produts, 2-8 NMMGR DTS ongurtion, 2-8 guided ongurtion, 2-8 NS3000/XL ongurtion le, 2-11 informtion les, 2-11 O Ojet Code Trnslted version HP DeskMnger, 3-2 OPERATORSYS reting, 4-9 P pth nmes dd to SYSGEN I/O ongurtion, 2-2 disply, 2-2 PC-sed network mngement, 2-8 R reovering your system, 4-1 resetting the system, 2-2 restrting the system reovery, 4-2 S setting psswords, 2-12 ounts, 2-12 users, 2-12 SNA IMF/XL Asin lnguge option, 3-3 English lnguge option, 3-3 instlling, 3-3 SPNAMES, 2-7 spoolles deleting, 4-9 stndlone HP DeskMnger, 3-1 strtup nd initiliztion messges, 2-4 SYSGEN ross vlidtion, 2-9 reovery, 4-7 system ooting the system, 2-1 restrt, 2-6 shutdown, 2-5 system ongurtion IOMAP, 2-5 system reovery, 4-1 system seurity, 2-13 system shutdown, 4-9 U UDC les HP DeskMnger, 3-1 users setting psswords, 2-12 UTILITY option vlidting ongurtion, 2-9 Index-2

47 V vlidting ongurtion Utility option, 2-9 VOLUTIL onguring system disks, 2-7 reovery, 4-7 Index-3

48