µ-precision measuring heads and chamfer measuring instruments Overall catalog English HEXACON TiN COATED 2200 HV 100 % 0,4 0,2 0,6 0,4 0,8

Transcription

1 ABS mm SETPR ABS HEXACON Made n,1 mm 9 9 9,4,2,6,4,6,8,8 1 9, TOL ON / OFF SET TOL MENU Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PRESET DATA RESET Englsh Ø µ-precson measurng heads and chamfer measurng nstruments Overall catalog

2 Notes

3 Hexacon Messtechnk GmbH specalzes n the area of precson hole and chamfer measurement. We manufacture hgh-precson hole measurng heads accordng to your ndvdual dameter specfcatons. Applcatons range from manual measurement to fully automated measurement. We also offer an extensve lne of system accessores. % Made n The repeat accuracy of our hole measurng heads at IT 8 s < 1µ. All Hexacon PMK precson measurng heads and chamfer measurng heads, chamfer probes and nserton measurng nstruments are tough, relable, hgh-precson metrology equpment made % here n! Ths allows the strctest of qualty requrements and standards for qualty assurance to be met. Our system accessores, such as gauge holders, centerng holders and depth extensons are also made n our own facltes, % Made n. The accessores are n stock n the warehouse. Know-how and years of experence Our engneerng servces n the area of techncal and producton technology development snce 1996 guarantee you perfect measurement problem solutons n the area of precson hole and chamfer measurement. Many years of experence n consultng and the mplementaton of customer-specfc problems offer you a hgh level of know-how for measurement tasks n producton as well as n qualty assurance. Ttanum ntrde coatng All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualtymprovng ttanum ntrde coatng. Ths has been our standard for many years. Made n - Precson Hgh Prec TN COATED 2 HV % on - Made n TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth outstandng sldng and frcton characterstcs. TN coatngs also slde easly to prevent the measurement object from tltng and stckng durng the measurement procedure. Ths results n less wear and longer lfe for measurement tools, as well as greater cost-effectveness. Precson measurng ponts The measurng ponts n the PMK measurng heads are precson fabrcated from tough, hgh-qualty coated hard metal. Damond measurng ponts of synthetc damond are avalable upon request. (Not for blnd hole varants and outer dameter measurng heads) Repar capablty and servce All our hole and chamfer measurng nstruments are not only robust, but are also outstandngly capable of repar. Our servces nclude the delvery of orgnal replacement parts up to and ncludng complete refurbshment and remanufacture of worn measurng tools to as-new condton, as well as recalbraton of metrology equpment. Advantages of our products at a glance: Top qualty and precson n fabrcaton and measurement accuracy. Robust, feld-ready metrology equpment for effectve, ratonal measurement. TN coatng provdes hgher servce lfe at no addtonal cost. Refned system accessores, for both manual and automated measurement. Flexble adaptaton and modfcaton to customer specfcatons as well as specal solutons are possble. Great prces and short delvery tmes % Made n Company headquartered n Deburg, Hessen.

4 Hole measurng nstruments Functonal prncple PMK precson hole measurng heads TN coated For qualty assurance n fabrcaton and n testng. 1 - Precson Made n Hgh Prec TN COATED 2 HV % on - Made n PMK precson meas. heads Functonal descrpton PMK measurng heads are used for the relable, rapd precson measurement of dameters and form errors n holes of a wde varety of types HEXACON Made n,1 mm 9 9 9,4,2,6,4,6,8,8 1 9, Dal gauge The purely mechancal measurement prncple uses hardened metal measurng ponts to probe the hole, then gude the force through measurement rods nto the housng onto a hardened, concally ground drve needle. A measurement gauge holder, wth or wthout drve needle, connects the measurng head to correspondng dsplays such as analog or dgtal dal gauges usng nductve measurng probes, measurng columns or automatc computer measurement systems. By sldng nto the depth of the hole durng the measurement process, any concty n the hole can be measured as well. TN s advantageous here. Usng a rotatonal probng movement nto the hole, addtonal form errors n the hole can be measured: Holder Ellptcal form errors, whch often occur n drlled holes, can be detected and measured wth hgh precson usng 2-pont measurng heads. Polygonal form errors, whch frequently occur n turned or cast parts, can be measured wth equal precson usng 3-pont measurng heads. Drve needle housng Drllng measurngobject Ø Drve needle Measurng pont Workpeace Measurng heads are avalable n round, concal, parallel, rectlnear or square shapes. We also provde mult-pont measurng heads as well as correspondng dal gauge holders and depth extensons, measurement stands, dal gauges and addtonal accessores. All Hexacon measurng heads are % Made n. X L1 L2 8H7 Measurng prncple 1 2-pont meas. 1 3-pont meas. B Ø D Parallel meas. B Parallel square B2 B B2 Parallel rectangle D2 D1 α M35x1,5 od. Mx1,5 Concal mult-pont measurng head 8H7

5 Hole measurng nstruments Propertes and calbraton - Precson Made n Hgh Prec TN COATED 2 HV % on - Made n PMK precson hole measurng heads TN coated Dameters from 6-2 mm Repeat accuracy at IT 8 down to < 1µ. Factory calbraton of measurng heads Upon request you can receve a factory calbraton certfcate for the measurng head. For hole measurng heads we guarantee a repeat accuracy less than 1µ, and that accuracy s often even exceeded, as shown agan and agan by measurement protocols. Long-lastng precson metrology equpment Due to the mature desgn, robust constructon and hgh-qualty machnng, we provde partcularly relable, long-lastng precson metrology equpment. Cleanng, servce The ttanum ntrde coatng gve PMK measurng heads drt- and water-repellng qualtes and make them easy to clean and servce. For worn parts such as sprngs or drve needles, we keep all spare parts n stock n the warehouse. Repar When necessary, these measurng heads are easy to repar and restore to lke-new condton and can also be recertfed upon request. Hexacon Messtechnk GmbH produces hgh-qualty precson metrology nstruments for ndustry and handcraft busnesses.

6 Hole measurng nstruments PMK - techncal characterstcs Measurng ponts Dameters and rad Ø Measurng ponts Dameters and rad The measurng ponts n all Hexacon PMK precson measurng heads are made of coated hard metal, ground and polshed. They are extremely tough, wth a long servce lfe. The measurng ponts are sutable not only for measurng steels, but also alumnum workpeces! Damond measurng ponts, PKD-MKO upon request. Not avalable for blnd hole varants and outer dameter measurng heads. PMK Measurng ponts Dameters and rad for PMK-NO and PMK-XK PMK body dameter Ø mm Outer measurng pont Ø mm Radus measurng pont mm Type Type PMK-EF Measurng ponts Dameters and rad for PMK-EF PMK body dameter Ø mm Outer measurng pont Ø mm Radus measurng pont mm Type Type

7 Product drectory PMK precson hole measurng heads TN coated Dameters from ø 6-2 mm Repeat accuracy at IT 8 down to < 1µ. - Precson Made n Hgh Prec TN COATED 2 HV % on - Made n 2-pont measurement 1 2-pont hole measurement heads wth nserton groove: X dmenson: Normal... PMK NO Page 12 X dmenson: Short... PMK XK Page 14 X dmenson: Blnd hole... PMK SL Page 16 1 For automated measurement 2-pont hole measurement heads wth nserton chamfer: X dmenson: Normal... PMK NO-EF Page 18 X dmenson: Short... PMK XK-EF Page X dmenson: Normal 2-zone dameter... PMK NO-EF-2D Page 22 X dmenson: Short 2-zone dameter... PMK XK-EF-2D Page 24 3-pont measurement 1 3-pont hole measurement heads wth nserton groove: X dmenson: Normal... PMK NO-3P Page 26 X dmenson: Short... PMK XSO-3P Page 28 For automated measurement 3-pont hole measurement heads wth nserton chamfer: X dmenson: Normal... PMK NO-3P-EF Page X dmenson: Short... PMK XSO-3P-EF Page 32 X dmenson: Normal 2-zone dameter... PMK NO-3P-EF-2D Page 34 X dmenson: Short 2-zone dameter... PMK XSO-3P-EF-2D Page 36 Parallel meas., square B B2 2-pont parallel hole measurng heads, square form: Parallel meas., round B Ø D Wdth 8-15 mm X dmenson: normal, short, blnd hole PMK 2-PA Page 38 Wdth 15- mm X dmenson: normal, short, blnd hole PMK 3-PA Page 39 2-pont parallel hole measurng heads, round form: Wdth 8-15 mm X dmenson: normal, short, blnd hole PMK 2-PA Page Wdth 15- mm X dmenson: normal, short, blnd hole PMK 3-PA Page 42 Page 7

8 9,1 mm Product drectory Specal precson measurng heads Outer meas. heads Concal and mult-pont meas. heads Inserton measurng devces 1 Parallel measurement, rectangle 2-pont parallel hole measurng heads, rectlnear form Wdth -1 mm, X dmenson: normal, short, blnd hole PMK NO-3-PA Page 44 Crankshaft meas. nstrument 2-pont crankshaft parallel measurng head X dmenson: 3 mm and up... PMK KW Page 46 Outer meas. heads 2-pont precson outer measurng head X dmenson Normal... PMK AM Page 48 Precson specal measurng heads... PMK SO Page 49 Tapered meas. heads Precson measurng heads n concal varant X dmenson Normal... PMK KE Page 5 Mult-pont tapered meas. heads Mult-pont measurng heads n concal varant Concal measurement... PMK KE Page 52 Mult-pont meas. heads Mult-pont hole measurng heads Up to 4 measurng ponts... PMK ME Page 54 Inserton measurng Made n HEXACON PMK-ES Inserton measurng nstrument Wth large measurng range up to 15 mm... PMK ES Page 56 Page 8

9 Product drectory Dal gauge holders, centerng holders and depth extensons HEXACON Angle brackets, depth stops, stands and adjustment rngs. Dal gauge holders for PMK measurng heads Holder and accessores, example applcaton. Page 58 Holder and accessores, overvew. Page 59 Dal gauge holder for PMK-2 meas. heads M6x.75 thread... HM-2 Page Dal gauge holder for PMK-3 meas. heads Mx1 thread... HM-3 Page 62 Dal gauge holder for PMK-3 rotatng Mx1 thread... HM 3-15-RO Page 63 Dal gauge holder for heavy meas. heads M6x.75 thread... HA-V2 Page 64 Dal gauge holder for heavy meas. heads Mx1 thread... HA-V3 Page 64 Dal gauge holder for nductve meas. heads M6x.75 thread... HT-V2 Page 65 Dal gauge holder for nductve meas. heads Mx1 thread... HT-V3 Page 65 Centerng holders for PMK measurng heads for automated measurement Centerng holder - floatng holder M6x.75 thread... ZH-PMK-2 Page 66 Centerng holder - floatng holder Mx1 thread... ZH-PMK-3 Page 66 Centerng holder wth ant-turnng protecton M6x.75 thread... ZH-PMK-2-VDS Page 68 Centerng holder wth ant-turnng protecton Mx1 thread... ZH-PMK-3-VDS Page 68 Centerng holder wth mountng flange Mx1 thread... ZH-LKM-3-5 Page 7 Centerng holder wth destructon protecton Mx1 thread... ZH-PMK-3-5-L Page 71 Dal gauge holders n modular system for custom setup Modular measurng systems, ø 8H7 dal gauge connecton... MB Page 72 Depth extensons for dal gauge holders - wth drve needle Depth extenson, also temperature stable M6x.75 thread... VL-2 Page 74 Depth extenson, also temperature stable Mx1 thread... VL-3 Page 75 Angle peces for measurng heads and depth extensons 9 angle pece for PMK-2 M6x.75 thread... WS-2 Page 76 9 angle pece wth ntegrated PMK M6x.75 thread... WS-SO-2 Page 76 9 angle pece wth ntegrated PMK Mx1 thread... WS-SO-3 Page 76 9 angle pece for PMK-3 Mx1 thread... WS-3 Page 77 Thread reducers Mx1 thread... RS Page 77 Depth stops for PMK measurng heads Clampng rng depth stops ø 6 mm to ø 85 mm... TA-KR-V Page 78 Depth stops for PMK-2 meas. heads M6x.75 thread... TA-2 Page 79 Depth stops as depth measurng head Example applcaton... TA-2-45 Page 79 Depth stops for PMK-3 meas. heads Mx1 thread... TA-3 Page Equpment stands and measurng stands Equpment stands, extensble up to 6 stands... GS-PMK-1 Page 82 Measurement stand sutable for larger workpeces... UMS-1 Page 84 Measurement stand wth ntegrated centerng holder... UMS-2 Page 85 Adjustment rngs wth nomnal DIN C standard dmensons Adjustment rngs... Adjustment rngs DIN 225 Page 86 Page 9

10 Product drectory Precson nner and outer chamfer measurng nstruments, dal gauges, test workstaton, nductve measurng probes. Precson nner and outer chamfer measurng nstruments Functonal prncple of chamfer measurng nstruments... Page 87 Inner and outer chamfer measurng nstruments Inner chamfer Measurng nstruments for 9 chamfers... FM-SB Page 88 Outer chamfers Measurng nstruments for 9 chamfers... FM-FB Page 89 Inner chamfer Measurng nstruments for chamfers... FM-SA Page 9 Outer chamfers Measurng nstruments for chamfers... FM-FA Page 91 Inner chamfer Measurng nstruments for 127 chamfers... FM-SC Page 92 Outer chamfers Measurng nstruments for 127 chamfers... FM-FC Page 93 Prsmatc chamfer probe for 9 chamfers Chamfer probe 9 For 9 workpeces... FT-1 Page 94 wth dal gauge Analog chamfer specal dal gauges Specal dal gauges for 9 chamfers Wth.1 mm dsplay accuracy... AD-FM Page 95 Analog precson ndcators and dal gauges, dgtal dal gauges, dal gauge test stand, nductve measurng probes Analog dal gauges for PMK measurng heads... Page 97 Dal gauge Precson ndcator Scale dvson value.1 mm... MU Page 98 Dal gauge Concentrc scale arrangement Scale dvson value.1 mm... MU 1-1 Page 98 Dal gauge Precson ndcator Scale dvson value.1 mm... MU 2-1 Page 98 Dal gauge Scale dvson value.1 mm... MU 2-1 Page 99 Dgtal dal gauge Numerc step value.1 mm... MU 4-1 Page 99 Dgtal dal gauge Wth factor settng Numerc step value.1 mm... MU 5-1 Page 99 Test workstaton for dal gauges and precson ndcators Test workstaton for dal gauges Based on DIN 878 and DIN MU-PS Page and precson ndcators Inductve measurng probes for PMK measurng heads and chamfer measurng nstruments Inductve measurng probes Resoluton.1 µm - TN coated... IT-1 Page 1 Inductve measurng probes Resoluton.1 µm - TN coated... IT-2 Page 1 (wth radal cable arrangement) Example applcatons Assembly examples for dfferent elements... Page 2 Notes Notes page... Page 3 Page

11 Precson measurng heads PMK 2-pont precson measurng heads 3-pont precson measurng heads Mult-pont precson measurng heads - Precson Made n Hgh Prec TN COATED 2 HV % on - Made n 2-pont PMK Precson measurng heads PMK wth nserton groove wth normal X-dmenson, short X-dmenson and blnd hole X-dmenson PMK wth nserton chamfer for automatc measurement wth normal X-dmenson and short X-dmenson PMK wth nserton chamfer and two dameters for automatc measurement wth normal X-dmenson and short X-dmenson 3-pont PMK Precson measurng heads HEXACON Made n,1 mm 9 9 9,4,2,6,4,6,8,8 1 9, PMK wth nserton groove wth normal X-dmenson and short X-dmenson PMK wth nserton chamfer for automatc measurement wth normal X-dmenson and short X-dmenson PMK wth nserton chamfer and two dameters for automatc measurement wth normal X-dmenson and short X-dmenson 2-pont PMK Precson parallel measurng heads PMK measurng heads n square form, round form, or rectlnear form wth normal or short X-dmenson, or blnd hole X-dmenson, also crankshaft parallel measurng heads 2-pont PMK Outer measurng nstrument 2-pont PMK Cone measurng heads 2-pont PMK Mult-pont tapered measurng heads 2-pont PMK Mult-pont measurng heads 2-pont PMK Inserton measurng nstrument Ø X L1 L2 Measurng prncple 1 2-pont meas. 1 3-pont meas. B Ø D Parallel meas. B Parallel square B2 B Parallel rectangle B2 D2 D1 α M35x1,5 od. Mx1,5 Concal mult-pont measurng head 8H7 8H7 Page 11

12 2-pont hole meas. heads PMK NO Normal X-dmenson TN coatng Measurement of through holes. Repeat accuracy at IT 8 < 1µ. ø 6-2 mm 1 Damond measurng ponts, PMK-NO upon request. PMK NO-2 Ø 6-8 mm Normal X dm. 5 mm M6x.75 mm thread PMK-NO-2 Precson meas. head n normal varant ø 6-8 mm, delvered wth standard X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 6 H7 = PMK - NO PMK NO-2 Ø 8 - mm Normal X dm. 5 mm M6x.75 mm thread PMK-NO-2 Precson meas. head n normal varant ø 8- mm, delvered wth standard X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - NO PMK NO-3 Ø 15 - mm Normal X dm. 6 mm PMK-NO-3 Precson meas. head n normal varant ø 15- mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK - NO Page 12

13 2-pont PMK-NO hole measurng heads wth normal X dmenson and ttanum ntrde coatng measure precse dameters, ovalty by rotaton durng the measurng procedure, and concty or deformaton of the hole. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK NO-3 Ø - 5 mm Normal X dm. 6 mm PMK-NO-3 Precson meas. head n normal varant ø -5 mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - NO ,95 PMK NO 2-pont PMK NO-3 Ø 5-2 mm Normal X dm. startng at 7.5 mm PMK-NO-3 Precson meas. head n normal varant ø 5-2 mm, delvered wth standard X dmenson and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 94 D = PMK - NO ,12 Ø Z X l L > > Accessores Depth extenson startng on page 74 Dal gauge holder startng on page Page 13

14 2-pont hole meas. heads PMK XK Short X-dmenson TN coatng Measure blnd holds close to the bottom of the hole. Repeat accuracy at IT 8 < 1µ. ø 6-2 mm 1 Damond measurng ponts, PMK-NO upon request. PMK XK-2 Ø 6-8 mm Short X dm. 1.6 mm M6x.75 mm thread PMK-XK-2 Precson meas. head wth short X dm. ø 6-8 mm, delvered wth X dmenson of 1.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 6 H7 = PMK - XK PMK XK-2 Ø 8 - mm Short X dm. 1.6 mm M6x.75 mm thread PMK-XK-2 Precson meas. head wth short X dm. ø 8- mm, delvered wth X dmenson of 1.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - XK PMK XK-3 Ø 15 - mm Short X dm. 2.5 mm PMK-XK-3 Precson meas. head wth short X dm. ø 15- mm, delvered wth X dmenson of 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK - XK Page 14

15 2-pont PMK-NK hole measurng heads wth short X dmenson and ttanum ntrde coatng measure blnd holes close to the bottom of the hole and measure precse dameters, ovalty by rotaton durng the measurng procedure, and the concty or deformaton of the hole. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK XK-3 Ø - 5 mm Short X dm. 2.5 mm PMK-XK-3 Precson meas. head wth short X dm. ø -5 mm, delvered wth X dmenson of 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - XK ,95 PMK XK 2-pont PMK XK-3 Ø 5-2 mm Short X dm. 2.5 mm PMK-XK-3 Precson meas. head wth short X dm. ø 5-2 mm, delvered wth X dmenson 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 62 ±.5 = PMK - XK ,95 Ø Z X l L > > Page 15

16 2-pont hole meas. heads PMK SL Blnd hole measurng heads TN coatng Measure deep nto the bottom of the hole. Repeat accuracy at IT 8 < 1µ. ø - 1 mm 1 Damond measurng ponts not avalable for PMK-SL varant. PMK SL-2 Ø - mm Short X dm..6 mm M6x.75 mm thread PMK-SL-2 Precson meas. head wth blnd hole X dm. ø - mm, delvered wth very short X dmenson of.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. Ther measurng range s.15 mm. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng ,5 M6x,75 Orderng example: Ø workpece = 12 H7 = PMK - SL Z -,15 -,5 X,6 SW7 PMK SL-3 Ø 15 - mm Short X dm. 1.2 mm PMK-SL-3 Precson meas. head wth blnd hole X dm. ø 15- mm, delvered wth very short X dmenson of 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.3 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - SL PMK SL-3 Ø - 5 mm Short X dm. 1.2 mm PMK-SL-3 Precson meas. head wth blnd hole X dm. ø -5 mm, delvered wth very short X dmenson of 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.3 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 D = PMK - SL ,8 Page 16

17 2-pont PMK-SL hole measurng heads wth blnd hole X dmenson and ttanum ntrde coatng measure deep nto the hole and measure precse dameters, ovalty by rotaton durng the measurng procedure, and the concty or deformaton of the hole. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK SL-3 Ø 5-1 mm 37,5 28,5 Short X dm. 1.2 mm PMK-SL-3 Precson meas. head wth blnd hole X dm. ø 5-1 mm, delvered wth very short X dm. of 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.3 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. PMK SL 2-pont Orderng example: Ø workpece = 124 D = PMK - SL ,15 Blnd hole measurng heads PMK-SL Blnd hole measurng heads The poston and specal geometry of the measurng ponts n blnd hole measurng heads permt precson measurement deep nto the bottom of the hole. The nserton groove permts the precson gudance of the measurng head and prevents tltng durng nserton nto the measurement object. Blnd hole measurng head measures deep nto the bottom of the hole Inserton groove Blnd hole meas. pont Page 17

18 2-pont hole meas. heads PMK-NO-EF Meas. heads for automated measurement The specal geometry of the measurng heads wth nserton chamfers prevents stckng. Also used wth our ZH-PMK centerng holders. ø - 2 mm 1 Damond measurng ponts, PMK-NO-EF upon request. PMK NO-2-EF Ø - mm NEW! Normal X dm. 5 mm M6x.75 mm thread Meas. pont radus R = 2 mm PMK-NO-2-EF Meas. head for automated meas. ø - mm, delvered wth standard X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - NO EF - 18 PMK NO-3-EF Ø 15 - mm Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-EF Meas. head for automated meas. ø 15- mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK - NO EF - 38 PMK NO-3-EF Ø - 5 mm Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-EF Meas. head for automated meas. ø -5 mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - NO EF - 41,95 Page 18

19 2-pont PMK-NO-EF hole measurng head for automated measurement wth normal X dmenson. The specal geometry wth nserton chamfer prevents stckng durng the measurng process. Also used n combnaton wth centerng holders. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Normal X dmenson PMK NO-3-EF Ø 5-2 mm PMK-NO-3-EF Meas. head for automated meas. ø 5-2 mm, delvered wth standard X dmenson and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 84 D = PMK - NO EF - 84,12 L l Meas. pont radus R = 2.5 mm PMK Automated measurement Ø Z X l L > > X Example applcaton: Angle peces for measurng heads are avalable for PMK-2 wth M6x.75 threads and for PMK-3 wth Mx1 mm. Data startng on page 76. Angle extensons startng on page 76. Page 19

20 2-pont hole meas. heads PMK-XSO-EF Meas. heads for automated measurng The specal geometry of the measurng heads wth nserton chamfers prevents stckng. Also deal n combnaton wth our ZH-PMK centerng holders. ø - 2 mm 1 Damond measurng ponts, PMK-XSO-EF upon request. PMK XSO-2-EF Ø - mm NEW! Short X dmenson 3 mm M6x.75 mm thread Meas. pont radus R = 2 mm PMK-XSO-2-EF Meas. head for automated meas. ø - mm, delvered wth short X dmenson of 3 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng. The nserton chamfer prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - XSO EF - 18 X3 33,5 25 PMK XSO-3-EF Ø 15 - mm Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm PMK-XSO-3-EF Meas. head for automated meas. ø 15- mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. The nserton chamfer prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK - XSO EF ,5 29,5 X3,5 PMK XSO-3-EF Ø - 5 mm Short X dm. 3.5 mm PMK-XSO-3-EF Meas. head for automated meas. ø -5 mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. The nserton chamfer prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - XSO EF - 41,95 38,5 26,5 X3,5 Meas. pont radus R = 2.5 mm Page

21 2-pont PMK-XSO-EF measurng heads for automated measurement. The specal geometry of the measurng heads wth nserton chamfer prevents stckng durng the measurng process. Also used n combnaton wth our ZH-PMK centerng holders. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK XSO-3-EF Meas. pont radus R = 2.5 mm Ø 5-2 mm PMK-XSO-3-EF Meas. head for automated meas. ø 5-2 mm, delvered wth standard X dmenson 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. The nserton chamfer prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 64 D = PMK - XSO EF - 64,1 X3,5 38,5 29,5 Short X dm. 3.5 mm PMK Automated meas. EF measurng heads PMK-XSO-EF Meas. heads wth nserton chamfer for automated meas. The nserton chamfer permts relable gudance of the measurng head and prevents stckng durng nserton nto the measurement object. The poston of the measurng ponts n meas. heads wth short X dm. (XSO) permts precson measurement rght up close to the bottom of the hole. Meas. heads wth nserton chamfer (EF) for automated measurement Inserton chamfer Meas. pont, short X dm. Page 21

22 2-pont hole meas. heads PMK-NO-EF-2D Meas. heads for automated measurng The specal geometry of meas. heads wth nserton chamfer and 2-zone dameter prevent stckng, even for deeper measurements. ø - 2 mm 1 Damond measurng ponts, PMK-NO-EF-2D upon request. PMK NO-2-EF-2D Ø - mm Normal X dm. 5 mm M6x.75 mm thread Meas. pont radus R = 2 mm PMK-NO-2-EF-2D Meas. head for automated meas. ø - mm, delvered wth standard X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - NO EF - 2D D=Z-,3 PMK NO-3-EF-2D Ø 15 - mm Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-EF-2D Meas. head for automated meas. ø 15- mm, delvered wth standard X dmenson 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK - NO EF - 2D D=Z-,3 PMK NO-3-EF-2D Ø - 5 mm Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-EF-2D Meas. head for automated meas. ø -5 mm, delvered wth standard X dmenson 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - NO EF - 2D - 41,95 2D=Z-,3 Page 22

23 2-pont PMK-NO-EF-2D hole meas. head for automated meas. wth normal X dmenson. The specal geometry of the measurng heads wth nserton chamfers (EF) and the second dameter tapered towards the back (2D) prevent stckng even for a deeper measurement. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK NO-3-EF-2D Meas. pont radus R = 2.5 mm Ø 5-2 mm PMK-NO-3-EF-2D Meas. head for automated meas. ø 5-2 mm, delvered wth standard X dmenson and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 84 D = PMK - NO EF - 2D - 84,12 X L l 2D=Z-,3 Normal X dm. 6 mm PMK Automated measurement Ø Z X l L > > EF-2D measurng heads PMK-NO-EF-2D Measurng heads for automated measurement The specal geometry of the measurng heads wth nserton chamfer and second, tapered dameter prevents stckng durng the measurement process, even for deeper measurements. The measurng pont radus can be adapted upon request for measurng heads wth nserton chamfer. 2D=Z-,3 Inserton chamfer and 2 tapered dameters prevent stckng Page 23

24 2-pont hole meas. heads PMK-XSO-EF-2D Meas. heads for automated measurng The specal geometry of meas. heads wth nserton chamfer and 2-zone dameter prevent stckng, even for deeper measurements. ø - 2 mm 1 Damond measurng ponts, PMK-XSO-EF-2D upon request. PMK XSO-2-EF-2D Meas. pont radus R = 2 mm Ø - mm NEW! Short X dm. 3 mm M6x.75 mm thread PMK-XSO-2-EF-2D Meas. head for automated meas. ø - mm, delvered wth short X dmenson of 3 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 18 H7 = PMK - XSO EF - 2D - 18 X3 33,5 25 2D=Z-,3 PMK XSO-3-EF-2D Ø 15 - mm Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm PMK-XSO-3-EF-2D Meas. head for automated meas. ø 15- mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 38 H7 = PMK -XSO EF - 2D ,5 26,5 X3,5 2D=Z-,3 PMK XSO-3-EF-2D Ø - 5 mm Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm PMK-XSO-3-EF-2D Meas. head for automated meas. ø -5 mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 42 ±.5 = PMK - XSO EF - 2D - 41,95 38,5 26,5 X3,5 2D=Z-,3 Page 24

25 2-pont PMK-NO-2D measurng heads for automated measurement. The specal geometry of the measurng heads wth nserton chamfers and the second dameter tapered towards the back prevent stckng even for a deeper measurement. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK XSO-3-EF-2D Meas. pont radus R = 2.5 mm Ø 5-2 mm PMK-XSO-3-EF-2D Meas. head for automated meas. ø 5-2 mm, delvered wth standard X dmenson 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng, wth nserton chamfer, tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 64 D = PMK - XSO EF - 2D X3,5 38,5 29,5 2D=Z-,3 Short X dm. 3.5 mm PMK Automated measurement PMK n 2-pont measurement technology wth normal X-dmenson or short X-dmenson are avalable n dfferent varants of dameter Z = Ø 6 mm up to 2 mm n the standard verson! Ø Z up to 2 mm Other dmensons and specal needs upon request. ø Z up to 2 mm Page 25

26 3-pont hole meas. heads PMK-NO-3-3P 3-pont measurng heads Innovatve "true" 3-pont precson measurement technology precsely measures polygonal form errors n holes. ø 15 - mm 1 Damond measurng ponts, PMK-NO-3-P upon request. PMK NO-3-3P Ø 15 - mm Normal X dm. 6 mm PMK-NO-3-3P Precson meas. head n 3-pont desgn ø 15- mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - NO - 3-3P - PMK NO-3-3P Ø - 5 mm Normal X dm. 6 mm PMK-NO-3-3P Precson meas. head n 3-pont desgn ø -5 mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - NO - 3-3P - 44 PMK NO-3-3P (PMK-NO-3-3P > mm on request.) Ø 5 - mm PMK-NO-3-3P Precson meas. head n 3-pont desgn ø 5- mm, delvered wth X dmenson of 7.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 98 H7 = PMK - NO - 3-3P ,5 33,5 X 7,5 Normal X dm. 7.5 mm Page 26

27 3-pont PMK-NO measurng heads wth ttanum ntrde coatng. Ths unque measurement technology mplements true 3-pont measurement to measure polygons, dmensons, and form errors n holes that other measurng nstruments can't, or can't easly, measure. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK measurng heads wth ntegrated depth stop Upon request, depth stops ntegrated nto the measurng body are avalable for nearly all varants. Depth stops ntegrated n the housng PMK NO 3-pont PMK n 3-pont measurng technology wth normal X-dmenson or short X-dmenson s avalable dependng on varants from a dameter of Z = ø 15 to mm n the standard verson. All 3-pont meas. heads are avalable up to ø mm! Other dmensons and specal needs upon request. ø Z up to mm Page 27

28 3-pont hole meas. heads PMK-XSO-3-3P 3-pont meas. heads wth short X dm. Innovatve true 3-pont precson measurement technology precsely measures polygonal form errors n holes. ø 15 - mm 1 Damond measurng ponts, PMK-XSO-3-3P upon request. PMK XSO-3-3P Ø 15 - mm NEW! Short X dm. 3.5 mm PMK-XSO-3-3P Precson meas. head n 3-pont desgn ø 15- mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread.. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - XSO - 3-3P - 38,5 26,5 X3,5 PMK XSO-3-3P Ø - 5 mm Short X dm. 3.5 mm PMK-XSO-3-3P Precson meas. head n 3-pont desgn ø -5 mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - XSO - 3-3P - 44 PMK XSO-3-3P Ø 5 - mm 38,5 26,5 X3,5 38,5 29,5 Short X dm. 3.5 mm PMK-XSO-3-3P Precson meas. head n 3-pont desgn ø 5- mm, delvered wth short X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton groove. Specfy the smallest hole dmenson when orderng. Orderng example: ( > mm on request.) Ø workpece = 98 H7 = PMK - XSO - 3-3P - 98 X3,5 Page 28

29 3-pont PMK-XSO-3-3P measurng heads wth ttanum ntrde coatng measure close to the bottom of the hole. Ths unque measurement technology mplements true 3-pont measurement to measure polygons, dmensons, and form errors n holes that other measurng nstruments can't, or can't easly, measure. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK XSO 3-pont All 3-pont meas. heads are avalable up to ø mm! 1 PMK n 3-pont measurng technology wth normal X-dmenson or short X-dmenson s avalable dependng on varants from a dameter of Z = ø 15 to mm n the standard verson. Other dmensons and specal needs upon request. Page 29

30 3-pont hole meas. heads PMK NO-3-3P-EF 3-pont meas. heads for automated meas. True" 3-pont precson meas. technology. The specal geometry of the meas. heads wth nserton chamfer (EF) prevents stckng. ø 15 - mm 1 Damond measurng ponts, PMK-NO-3-3P-EF upon request. PMK NO-3-3P-EF Ø 15 - mm NEW! Normal X dm. 6 mm PMK-NO-3-3P-EF Precson meas. head n 3-pont desgn ø 15- mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - NO - 3-3P - EF - X6 PMK NO-3-3P-EF Ø - 5 mm Normal X dm. 6 mm PMK-NO-3-3P-EF Precson meas. head n 3-pont desgn ø -5 mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - NO - 3-3P - EF - 44 PMK NO-3-3P-EF Ø 5 - mm X6 42,5 33,5 Normal X dm. 7.5 mm PMK-NO-3-3P-EF Precson meas. head n 3-pont desgn ø 5- mm, delvered wth X dmenson of 7.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: ( > mm on request.) Ø workpece = 98 H7 = PMK - NO - 3-3P - EF - 98 X7,5 Page

31 3-pont PMK-NO-3-3P-EF precson measurng heads for automated measurement of dameters. The specal geometry of the measurng heads wth nserton chamfer prevents stckng durng the measurng process. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Automated meas. 3-pont PMK XV Varable X-dm. NEW! 3-pont measurng head wth varable X dmenson L X-poston varable PMK-XV Precson measurng head wth varable X-dmenson PMK n 3-pont measurement technology avalable wth modfed housng dmensons dependng on varant. Ths allows, for example, varable postonng of the X-dmenson due to a longer housng form. Detals upon request. Page 31

32 3-pont hole meas. heads 3-pont PMK-XSO-3-3P-EF For automated measurement Wth short X-dmenson of 3.5 mm. ø 15 - mm 1 Damond measurng ponts, PMK-XSO-3-3P-EF upon request. PMK XSO-3-3P-EF Meas. pont radus R = 2.5 mm Ø 15 - mm NEW! Short X dm. 3.5 mm PMK-XSO-3-3P-EF Precson meas. head n 3-pont desgn ø 15- mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - XSO - 3-3P - EF - X3,5 38,5 26,5 PMK XSO-3-3P-EF Ø - 5 mm Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm PMK-XSO-3-3P-EF Precson meas. head n 3-pont desgn ø -5 mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - XSO - 3-3P - EF - 44 PMK XSO-3-3P-EF Meas. pont radus R = 2.5 mm Ø 5 - mm X3,5 38,5 26,5 38,5 29,5 Short X dm. 3.5 mm PMK-XSO-3-3P-EF Precson meas. head n 3-pont desgn ø 5- mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Specfy the smallest hole dmenson when orderng. Orderng example: ( > mm on request.) Ø workpece = 98 H7 = PMK - XSO - 3-3P - EF - 98 X3,5 Page 32

33 3-pont PMK-XSO-3-3P-EF precson meas. heads for automated measurement of dameters, wth short X dmenson. The specal geometry of the measurng heads wth nserton chamfers and the second dameter tapered towards the back prevent stckng durng measurement. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Automated meas. 3-pont 2-chamfer measurng heads Two chamfer measurng heads for automated measurng PMK-2EF-2D Measurng heads for automated measurement The specal geometry of the measurng heads wth two-sded nserton chamfers (2EF) prevents stckng both durng nserton as well as durng retracton of the measurng head durng the automated measurng process. The second chamfer on the measurng head can be mplemented n nearly all 2-pont and 3-pont measurng heads wth NO, XK, and SL X-dmensons. Frst chamfer Second chamfer NEW! Page 33

34 3-pont hole meas. heads PMK NO-3-3P-EF-2D 3-pont measurng heads for automated measurng The specal geometry of the measurng heads wth nserton chamfer and 2 tapered dameters prevents stckng. ø 15 - mm 1 Damond measurng ponts, PMK NO-3-3P-EF-2D upon request. PMK NO-3-3P-EF-2D Ø 15 - mm NEW! Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-3P-EF-2D Precson meas. head n 3-pont desgn ø 15- mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - NO - 3-3P - EF - 2D - X6 2D=Z-,3 PMK NO-3-3P-EF-2D Ø - 5 mm Normal X dm. 6 mm Meas. pont radus R = 2.5 mm PMK-NO-3-3P-EF-2D Precson meas. head n 3-pont desgn ø -5 mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - NO - 3-3P - EF - 2D - 44 X6 2D=Z-,3 PMK NO-3-3P-EF-2D Ø 5 - mm Meas. pont radus R = 2.5 mm PMK-NO-3-3P-EF-2D ø > mm upon request PMK-NO-3-3P-EF-2D Precson meas. head n 3-pont desgn ø 5- mm, delvered wth X dmenson of 7.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 98 H7 = PMK - NO - 3-3P - EF -2D ,5 33,5 X7,5 2D=Z-,3 Normal X dm. 7.5 mm Page 34

35 3-pont PMK-NO-3-3P-EF-2D precson measurng heads for automated measurement of dameters. The specal geometry of the measurng heads wth nserton chamfers and the second dameter tapered towards the back prevent stckng even for a deeper measurement. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Automated meas. 3-pont HEXACON 7 Made n 5,1 mm 7 9,4, ,6,4,6,8,2,8 1 Example applcaton: Accessores Depth stops for PMK startng on page 78 Depth stop - clampng rng Page 35

36 3-pont hole meas. heads PMK XSO-3-3P-EF-2D 3-pont meas heads for automated measurng Wth short X-dmenson of 3.5 mm. ø 15 - mm 1 Damond measurng ponts, PMK XSO-3-3P-EF-2D upon request. PMK XSO-3-3P-EF-2D Ø 15 - mm NEW! Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm PMK-XSO-3-3P-EF-2D 3-pont precson meas. head ø 15- mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - XSO - 3-3P - EF - 2D- PMK XSO-3-3P-EF-2D Ø - 5 mm PMK-XSO-3-3P-EF-2D 3-pont precson meas. head ø -5 mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 44 H7 = PMK - XSO - 3-3P - EF - 2D - 44 PMK XSO-3-3P-EF-2D Ø 5 - mm Meas. pont radus R = 2.5 mm PMK-XSO-3-3P-EF-2D ø > mm upon request X3,5 X3,5 38,5 26 2D=Z-,3 38,5 26 2D=Z-,3 38,5 29,5 Short X dm. 3.5 mm Meas. pont radus R = 2.5 mm Short X dm. 3.5 mm PMK-XSO-3-3P-EF-2Z 3-pont precson meas. head ø 5- mm, delvered wth X dmenson of 3.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng, wth nserton chamfer. Tapered measurng body prevents stckng. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = 98 H7 = PMK - XSO - 3-3P - EF - 2D - 98 X3,5 2D=Z-,3 Page 36

37 TOL SET TOL MENU ON / OFF ABS mm PRESET DATA RESET SETPR ABS 3-pont PMK-XK-3-3P-EF-2D precson measurng heads for automated measurement of dameters, wth short X dmenson. The specal geometry of the measurng heads wth nserton chamfers and the second dameter tapered towards the back prevent stckng even for a deeper measurement. The repeat accuracy of our 3-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Automated meas. 3-pont Example applcaton: Devce stands and measurement stands permt relable, effcent measurement. On the largest workpeces n seres or n testng. Startng on page 82. Extensble to up to 6 ponts! Page 37

38 Square parallel meas. heads PMK-2-PAQ Parallel measurng heads, square form. B2 Measurng square forms Thread M6x.75 mm. B 8-15 mm Damond measurng ponts, PMK-2-PAQ-NO and PMK-2-PAQ-XK upon request. PMK NO-2-PAQ Ø 8-15 mm NEW! B Normal X dm. 5 mm M6x.75 mm thread PMK-NO-2-PAQ Square meas. head n normal varant B 8-15 mm, delvered wth X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Specfy the smallest dmenson B of the parallels when orderng. Orderng example: B workpece = 14 H7 = PMK - NO PAQ - 14 PMK XK-2-PAQ Ø 8-15 mm PMK-XK-2-PAQ Square meas. head, short X dmenson B 8-15 mm, delvered wth short X dmenson of 1.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Specfy the smallest dmenson B of the parallels when orderng. B2 B2 B B B2 -,3 B2 -,3 Tolerance B Short X dm. 1.6 mm M6x.75 mm thread Tolerance B Orderng example: B workpece = 14 H7 = PMK - XK PAQ - 14 PMK SL-2-PAQ Ø - 15 mm PMK-SL-2-PAQ Square meas. head n blnd hole varant B -15 mm, delvered wth very short X dmenson of.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. Ther measurng range s.15 mm. Specfy the smallest dmenson B of the parallels when orderng. B2 B B2 -,3 Blnd hole X dm..6 mm M6x.75 mm thread Tolerance B Orderng example: B workpece = 15 H7 = PMK - SL PAQ - 15 Page 38

39 2-pont PMK-PAQ square parallel measurng heads wth ttanum ntrde coatng precsely measure the parallelsm of two surfaces. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK NO-3-PAQ Ø 15 - mm PMK-NO-3-PAQ Square meas. head n normal varant B 15- mm, delvered wth X dmenson 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Specfy the smallest dm. B of the parallels when orderng. Orderng example: B workpece = 18 H7 = PMK - NO PAQ - 18 PMK XK-3-PAQ Ø 15 - mm PMK-XK-3-PAQ Square meas. head n normal varant B 15- mm, delvered wth short X dmenson of 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Specfy the smallest dm. B of the parallels when orderng. Orderng example: B workpece = 35 H7 = PMK - XK PAQ - 35 PMK SL-3-PAQ Ø 15 - mm PMK-SL-3-PAQ Square meas. head n blnd hole varant B 15- mm, delvered wth very short X dmenson 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.3 mm upon request. Specfy the smallest dm. B of the parallels when orderng. NEW! B B2 B2 B2 B B B2 -,3 B2 -,3 B2 -,3 Normal X dm. 6 mm Tolerance B Short X dm. 2.5 mm Tolerance B Blnd hole X dm. 1.2 mm Tolerance B PMK PAQ Square form Orderng example: B workpece = 34 D = PMK - SL PAQ Page 39

40 2-pont parallel meas. head PMK-2-PA Precson parallel measurng heads Ø D Precse measurement of parallel surfaces. B 8-15 mm B Damond measurng ponts upon request for PMK-NO-2-PA and PMK-XK-2-PA varant. PMK NO-2-PA Ø 8-15 mm NEW! ØD Normal X dm. 5 mm M6x.75 mm thread Tolerance B PMK-NO-2-PA Parallel meas. head n normal varant B 8-15 mm, delvered wth normal X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Specfy the smallest dm. B of the parallels when orderng. B 35,5 27 Orderng example: B workpece = 14 H7 = PMK - NO PA - 14 Ø D PMK XK-2-PA Ø 8-15 mm Short X dm. 1.6 mm M6x.75 mm thread B 32 23,5 Tolerance B Ø D PMK SL-2-PA Ø - 15 mm ØD ØD PMK-XK-2-PA Parallel meas. head, short X dmenson B 8-15 mm, delvered wth short X dmenson of 1.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Specfy the smallest dm. B of the parallels when orderng. Orderng example: B workpece = 14 H7 = PMK - XK PA - 14 Blnd hole X dm..6 mm M6x.75 mm thread PMK-SL-2-PA Parallel meas. head, blnd hole varant B -15 mm, delvered wth very short X dmenson of.6 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.3 mm upon request. Specfy the smallest dm. B of the parallels when orderng. Orderng example: B workpece = 15 H7 = PMK - SL PA - 15 B Ø D 32 23,5 Tolerance B Page

41 2-pont PMK-2-PA parallel measurng heads wth ttanum ntrde coatng precsely measure the parallelsm of two surfaces. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK PA Parallel meas. Body dameter for parallel measurng heads Tolerance B PMK body dameter Ø D ±.2 8 mm 11.3 mm 9 mm 12.7 mm mm 14.1 mm 11 mm 15.6 mm 12 mm 17. mm 13 mm 18.4 mm 14 mm 19.8 mm 15 mm 21.2 mm B Ø D Page 41

42 2-pont parallel meas. heads PMK-3-PA Precson parallel measurng heads Ø D Precse measurement of parallel surfaces. B 15 - mm B Damond measurng ponts, PMK-NO-3-PA and PMK-XK-3-PA upon request. PMK NO-3-PA Ø 15 - mm NEW! ØD Normal X dm. 6 mm Tolerance B PMK-NO-3-PA Parallel meas. head n normal varant B 15- mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Specfy the smallest dm. B of the parallels when orderng. B Orderng example: B workpece = 18 H7 = PMK - NO PA - 18 PMK XK-3-PA Ø 15 - mm Short X dm. 2.5 mm PMK-XK-3-PA Parallel meas. head, short X dmenson B 15- mm, delvered wth short X dmenson of 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Specfy the smallest dm. B of the parallels when orderng. B ØD Tolerance B Orderng example: B workpece = 35 H7 = PMK - XK PA - 35 PMK SL-3-PA Ø 15 - mm Blnd hole X dm. 1.2 mm PMK-SL-3-PA Parallel meas. head, blnd hole varant B 15- mm, delvered wth very short X dmenson 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.3 mm upon request. Specfy the smallest dm. B of the parallels when orderng. B ØD Tolerance B Orderng example: B workpece = 34 D = PMK - SL PA - 34,8 Page 42

43 2-pont PMK-3-PA parallel measurng heads wth ttanum ntrde coatng precsely measure the parallelsm of two surfaces. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Body dameter for parallel measurng heads Tolerance B PMK body dameter Ø D Ø D ±.2 15 mm 21.2 mm 15.5 mm 21.9 mm 16 mm 22.6 mm 16.5 mm 23.3 mm 17 mm 24. mm 17.5 mm 24.7 mm 18 mm 25.5 mm 18.5 mm 26.2 mm 19 mm 26.9 mm 19.5 mm 27.6 mm mm 28.3 mm 21 mm 29.7 mm 22 mm 31.1 mm 23 mm 32.5 mm 24 mm 33.9 mm 25 mm 35.6 mm 26 mm 36.8 mm 27 mm 38.2 mm 28 mm 39.6 mm 29 mm 41. mm mm 42.4 mm 32 mm 45.3 mm 35 mm 49.5 mm 36 mm 5.9 mm 38 mm 53.7 mm mm 56.6 mm B Ø D PMK PA Parallel meas. Page 43

44 2-pont parallel meas. heads PMK-3-PA Precson parallel measurng heads B2 Precse measurement of parallel surfaces. B - 1 mm B Damond measurng ponts, PMK-NO-3-PA and PMK-XK-3-PA upon request. PMK NO-3-PA Ø - 1 mm NEW! Normal X dm. 6 mm Tolerance B PMK-NO-3-PA Parallel meas. head n normal varant B -1 mm, delvered wth X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.8 mm upon request. B2 = approx. 25- mm -.3 mm. Specfy the smallest dm. B of the parallels when orderng. Orderng example: B workpece = 88 H7 = PMK - NO PA - 88 B2 SW17 - SW22 Short X dm. 2.5 mm B B2 PMK XK-3-PA Ø - 1 mm 37,5 25,5 Tolerance B PMK-XK-3-PA Parallel meas. head wth short X dm. B -1 mm, delvered wth short X dmenson of 2.5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas.range s.2 mm and can be extended to up to.8 mm upon request. B2=approx.25- mm-.3 mm. Specfy the smallest dm. B of the parallels when orderng. B2 B2 Orderng example: B workpece = 45 H7 = PMK - XK PA - 45 X2,5 SW17 - SW22 B PMK SL-3-PA Ø - 1 mm 37,5 25,5 Blnd hole X dm. 1.2 mm Tolerance B PMK-SL-3-PA Parallel meas. head n blnd hole varant B -1, delvered wth very short X dmenson 1.2 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The meas. range s.2 mm and can be extended to up to.3 mm upon request. B2=approx.25- mm-.3 mm. Specfy the smallest dm. B of the parallels when orderng. B2 B2 Orderng example: B workpece = 64 D = PMK - SL PA - 64,1 X1,2 SW17 - SW22 B Page 44

45 2-pont PMK-NO-3-PA parallel measurng heads wth ttanum ntrde coatng precsely measure the parallelsm of two surfaces. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK PA Parallel meas. PMK-PA Parallel meas. head delvered up to B = 1 mm Parallel measurng heads are avalable wth normal X-dmenson, short X-dmenson and blnd hole X-dmenson n standard varant. Parallel measurng heads up to wdth = 1 mm Avalable up to 1 mm wdth. B2 B B up to 1 mm Page 45

46 Crankshaft measurng heads PMK-KW Crankshaft parallel measurng heads B2 Wth precson 2-pont technology. B 6 mm and up B Damond measurng ponts, PMK-KW upon request. NEW! X dm. 2 mm and up M 6x.75 mm thread PMK 2-KW Ø 6 - mm PMK-2-KW Crankshaft parallel measurng head avalable wth M6x.75 mm thread and X dmenson 2 mm and up. Wdth from 6 to mm. Illustraton may dffer. D Orderng example: B workpece = 14 H7 = PMK KW - X -14 X 22 X dm. 3 mm and up PMK 3-KW Ø 15 mm and up Mx1 PMK-3-KW Crankshaft parallel measurng head avalable wth Mx1mm thread and X dmenson 3 mm and up. Wdth 15 mm and up. Illustraton may dffer. Orderng example: B workpece = H7 = PMK KW - X - D X 23 SW17 PMK-KW parallel crankshaft measurng heads wth ttanum ntrde coatng precsely measure the parallelsm of two surfaces. In varants wth connecton threads n M6x.75 and Mx1. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. n Made - Precson Hgh Prec TN COATED 2 HV % on - n Made Page 46

47 Notes Page 47

48 Outer measurng heads PMK-AM 2-pont outer measurng heads Precson measurement of outer dameters. For shaft ends and the lke PMK 2-AM L Outer meas. head NEW! X dmenson 5 mm M6x.75 mm thread PMK-2-AM Outer measurng head n normal varant ø 8-15 mm, delvered wth X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.6 mm upon request. Self-centerng. Orderng example: B workpece = 14 H7 = PMK AM - 14 D X Made - n Precson Hgh Prec TN COATED 2 HV % on - Made n PMK 3-AM Outer meas. head X dmenson 5 mm L X PMK-3-AM Outer measurng head n normal varant ø 15 mm and up, delvered wth X dmenson of 5 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. Orderng example: B workpece = H7 = PMK AM - D Mx1 Made n - Precson Hgh Prec TN COATED 2 HV % on - Made n 2-pont PMK-AM outer dameter measurng heads wth ttanum ntrde coatng precsely measure the outer dameter at shaft ends. In varants wth connecton threads n M6x.75 and Mx1. The repeat accuracy of our 2-pont outer measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Page 48

49 PMK specal measurng heads Modfcaton of measurng heads accordng to customer request PMK XV Varable X-dm. PMK-XV Precson meas. head wth varable X dmenson Many of our precson meas. heads are avalable wth modfed housng dmenson, dependng on the varant. The longer housng form means the X dm. can be postoned varably. Detals upon request. NEW! L X-poston varable PMK AM Outer measurement PMK Depth stop PMK measurng heads wth ntegrated depth stop Upon request, depth stops ntegrated nto the measurng body are avalable for dfferent varants. NEW! Detals upon request. PMK 2-EF 2-nserton chamfers PMK measurng heads wth 2-nserton chamfers Prevent stckng durng automated measurement. NEW! Detals upon request. Frst chamfer Second chamfer Page 49

50 2-pont concal meas. head PMK-NO-KE Precson meas. heads n concal varant Wth short X-dmenson, repeat accuracy at IT 8 < 1µ. ø 8-2 mm 1 Damond measurng ponts, PMK-NO/KE upon request. PMK NO-2-KE Ø 8 - mm NEW! Normal X dm. 5 mm M6x.75 mm thread PMK-NO-2-KE Precson meas. head n concal varant ø 8- mm, delvered wth standard X dmenson of 5 mm and M6x.75 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.15 mm and can be extended to up to.6 mm upon request. Self-centerng. Specfy Z, angle α, L, and concal slope when orderng. Z-,1 α 35,5 27 M6x,75 Orderng example: Ø workpece = 18 H7 = PMK - NO KE - 18 X5 L 5 SW7 PMK NO-3-KE Ø 15 - mm Normal X dm. 6 mm PMK-NO-3-KE Precson meas. head n concal varant ø 15- mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. Specfy Z, angle α, L, and concal slope when orderng. Z-,1 α Mx1 Orderng example: Ø workpece = 38 H7 = PMK - NO KE - 38 X6 L 8 SW13 PMK NO-3-KE Ø - 5 mm Normal X dm. 6 mm PMK-NO-3-KE Precson meas. head n concal varant ø -5 mm, delvered wth standard X dmenson of 6 mm and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. Specfy Z, angle α, L, and concal slope when orderng. Z-,1 α Mx1 Orderng example: Ø workpece = 45 H7 = PMK - NO KE - 45 X6 L 8 SW17 Page 5

51 2-pont PMK-KE concal hole measurng heads wth ttanum ntrde coatng measure precson dameters at a defned depth, ovalty by rotatng durng the measurement process, and form errors n the hole. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. A sample part and assocated drawng of the workpece s requred wth the order. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n PMK NO-3-KE Ø 5-2 mm Normal X dm. 6 mm PMK-NO-3-KE Precson meas. head n concal varant ø 5-2 mm, delvered wth standard X dmenson and Mx1 thread. Repeat accuracy at IT 8 < 1µ. The measurement range s.2 mm and can be extended to up to.8 mm upon request. Self-centerng. Specfy Z, angle α, L, and concal slope when orderng. Orderng example: Ø workpece = 34 D = PMK - NO KE - 34,8 Z-,1 α L I Mx1 PMK KE Concal meas. Ø Z X l L > > X L1 8 SW22 Concal PMK-NO-KE n 2-pont measurement technology avalable wth normal X-dmenson or short X-dmenson and from 6 mm to 2 mm dameter Z n the standard verson accordng to varant. Concal measurng heads up to wdth = ø 2 mm Other dmensons and specal needs upon request. ø Z up to 2 mm Page 51

52 Concal measurng heads PMK-ME-KE Mult-pont meas. heads n concal varant Wth ntegrated dal gauge or nductve probe holders. Integrated holder Ø 8H7 1 Concal measurement PMK ME-KE X Concal measurng head L PMK-ME-KE 2-pont concal precson measurng head delvered wth ntegrated holder for nductve measurng probes Ø 8H7 mm. Thread for handle M35x1.5 mm or Mx1.5 mm. Wth nserton chamfer. Depth stop usng Allen screws. In order nqury: Specfy X, L, D1, D2 and α angle. D2 D1 α PMK ME-KE X Mult-pont concal meas. head L1 L2 M35x1,5 od. Mx1,5 PMK-ME-KE Mult-pont concal precson measurng head delvered wth ntegrated holder for nductve meas. probes Ø 8H7 mm. Thread for handle M35x1.5 mm or Mx1.5 mm. Wth nserton chamfer. Depth stop usng Allen screws. In order nqury: Specfy X, L1, L2, D1, D2 and α angle. D2 D1 8H7 8H7 8H7 NEW! α Mult-pont concal head M35x1,5 od. Mx1,5 Page 52

53 2-pont PMK-KE concal and mult-pont concal measurng heads wth ttanum ntrde coatng measure precson dameters at a defned depth, ovalty by rotatng durng the measurement process and form errors n the hole. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n HM ME-M35 Handle for PMK-ME-KE For PMK-ME-KE NEW! HEXACON HM-ME-M35/M Handle for PMK-ME-KE Robust handle of alumnum for relable protecton and handlng of PMK-ME-KE concal metrology nstrument. Thread M35x1.5 Order no.: HM-ME-M35x1.5 Thread Mx1.5 Order no.: HM-ME-Mx1.5 PMK KE Concal meas. Illustraton: PMK-ME-KE concal measurng nstrument wth HM-ME-M35 handle and nductve probes mounted. Applcaton example Page 53

54 Mult-pont measurng heads PMK-ME Mult-pont measurng heads Wth precson mult-pont measurement technology Integrated holder Ø 8H7 PMK ME Two-pont meas. head Two-pont measurng head PMK-ME-2P Two-pont precson measurng head delvered wth ntegrated holder for nductve measurng probes wth Ø 8H7 mm. Integrated depth stop can be mplemented for example usng the housng geometry. Threaded connecton for handle M35x1.5 mm or Mx1.5 mm. In order nqury: Specfy Ø D1, D2, L1, L2, X1, X2. X1 X2 M35x1,5 Mx1,5 Ø D1 Ø D2 Ø 8H7 L1 L2 PMK ME Mult-pont meas. head X3 X2 X1 M35x1,5 Mx1,5 8H7 Mult-pont meas. head PMK-ME Mult-pont precson measurng head delvered wth ntegrated holder for nductve measurng probes wth Ø 8H7 mm. Integrated depth stop can be mplemented for example usng the housng geometry. Threaded connecton for handle M35x1.5 mm or Mx1.5 mm. In order nqury: Specfy Ø D1, D2, L1, L2, X1, X2. D3 D2 D1 L1 L2 Page 54

55 2-pont PMK-ME mult-pont measurng heads precsely measure the dmensons and form of two or more dameters. The measurng heads are delvered wth ntegrated Ø 8H7 mm dal gauge holder for nductve measurng probes. An ntegrated depth stop can be mplemented usng a clampng rng, stop screws or the housng structure. Thread for handle M35x1.5 mm or Mx1.5 mm. The repeat accuracy of our 2-pont measurng heads at IT 8 s < 1µ. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Depth stops Applcaton examples NEW! Mult-pont PMK ME Applcaton example: PMK-ME Two-pont measurng head wth housng structure as depth stop. Applcaton example: PMK-ME Two-pont measurng head wth adjustable TA-KR-V clampng rng as depth stop. Applcaton example: PMK-ME Two-pont measurng head wth stop screws as depth stop. HM-ME-M35/M Handle for PMK-ME-KE Robust handle of alumnum for relable protecton and handlng of mult-pont measurng nstrument PMK-ME-KE. Thread M35x1.5 - order no.: HM-ME-M35x1.5 Thread Mx1.5 - order no.: HM-ME-Mx1.5 HEXACON Page 55

56 9 7 Inserton meas. nstruments PMK-ES Inserton measurng nstruments and specal pstol holder wth ventlaton. 15 mm meas. range Made n,1 mm HEXACON 9 HM 3-AL-25 Wth ventlaton HM-3-AL-25 Specal holder wth ventlaton for PMK-ES For nserton measurement. For retracton of the meas. ponts for nserton measurng nstrument, see below for the PMK-ES as well as for PMK wth offset measurng ponts. Pullng back the measurement stroke on the holder, the measurng ponts can be extended or retracted by max. 15 mm Ø D - Ø d. Order no.: HM AL - 25 PMK ES For nserton meas. Normal X dm. 15 mm Mx1 mm thread PMK-ES Precson meas. head for nserton meas. ø 15 mm and up, delvered wth X dmenson of 15 mm and Mx1 thread. Dameter dfferences of up to 15 mm can be measured. Ideal for nserton measurement. Self-centerng, wth nserton groove. Depth stop clampng rng ncluded n delvery. Specfy the smallest hole dmenson when orderng. Orderng example: Ø workpece = H7 = PMK - ES n Made - Precson Hgh Prec TN COATED 2 HV % on - n Made Page 56

57 PMK-ES nserton measurng nstrument wth large measurement range and specal pstol holder measures precson dameter dfferences up to 15 mm. Wth ntegrated measurng gauge holder and Mx1 stop thread as well as depth stop clampng rng. The repeat accuracy of our 2-pont nserton measurng heads at IT 8 s < 1/ mm. All Hexacon PMK s are manufactured of hgh-qualty tool-grade steel and treated at no extra charge wth a qualty-mprovng ttanum ntrde coatng. TN coatng provdes very good hardness, about 2 HV, as well as corroson resstance wth very good sldng and frcton characterstcs. The mproved servce lfe results n hgh cost-effectveness as well as protecton of the measurement object. The measurement ponts are fabrcated from coated hard metal. Damond measurng ponts upon request. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Normal X dm. 15 mm Measurng set for nserton measurng PMK-ES Complete set for nserton measurement Consstng of: Measurng head, depth stops, pstol handle and dal gauge. ø 15 mm and up, delvered wth X-dmenson of 15 mm and Mx1 thread. Dameter dfferences of up to 15 mm can be measured. Ideal for nserton measurement. Self-centerng, wth nserton groove. Depth stop clampng rng ncluded n delvery. PMK ES Inserton measurng 7 Measurng range up to 15 mm Made n,1 mm HEXACON 9 9 Page 57

58 Holders and accessores System accessores for precson measurng heads HEXACON Made n,1 mm 9 9,6,4 9,4,2,6,8 9,2, Example applcaton: PMK measurng head wth HM 3-GS- holder, MU dal gauge and TA-3 depth stop base body Page 58

59 Dal gauge and accessores for PMK Pr e s cs on M a d e Extensons for dal gauge holder, devce stand and measurement stand - Precson Made n Hgh % y rm n G e Dal gauge holder for PMK measurng heads PMK-2 = M6x.75 mm thread Dal gauge holder for PMK measurng heads PMK-3 = Mx1 mm thread Dal gauge holder for heavy or robust dal gauges Measurement holder for nductve measurng heads Centerng holder for automated measurement Dal gauge holder n modular measurng system Dal gauge holder Centerng holder Measurement gauge holder for nductve measurng heads Extensons for dal gauge holders wth drve needle Angle peces for PMK measurng heads Depth stop clampng rngs for PMK measurng heads Depth stops n modular system for PMK Dal gauge Dal gauge holder Angle pece Extenson Measurng head Depth stop clampng rng TA-2 depth stop Dal gauge Dal gauge holder Angle pece Depth extenson Depth stop Devce stand Devce stand for seral measurement of compact workpeces Measurement stands sutable for larger workpeces Measurement stand ntegrated centerng holder Page 59

60 Standard dal gauge holders HM-2 dal gauge holders for PMK-2 measurng heads Wth ø 8H7 dal gauge connecton and knurled screw. M6 x.75 mm thread HM 2-32 Dal gauge holder M6 x.75 mm thread HM-2-32 Dal gauge for PMK-NO-2 Short varant 32 mm length, dameter mm, delvered wth M6 x.75 mm thread. Standard dal gauge shaft Ø 8mm H7. For specal dal gauges, short. Order no.: HM-2-32 HM 2-5 Dal gauge holder M6 x.75 mm thread HM-2-5 Standard dal gauge holder for PMK-NO-2 Short varant 5 mm length, dameter 8 mm H7, delvered wth M6 x.75 mm thread. HEXACON Order no.: HM-2-5 HM 2- Dal gauge holder M6 x.75 mm thread HM-2- Standard dal gauge holder for PMK-NO-2 Normal varant mm length, dameter 8 mm H7, delvered wth M6 x.75 mm thread. HEXACON Order no.: HM-2- Page

61 Dal gauge holder for PKM measurng heads of sze 2 = M6 thread, 8H7 dal gauge connecton. Sutable for all precson measurng heads n cylndrcal, concal, or parallel form wth M6x.75 mm thread. All varants n stable alumnum housng. Wth knurled screw. To avod falsfyng the measurement results due to heat from the hands, the HM-2-15 sze temperature-stable steel (!) s used. Temperaturestable! Hgh Precson - Made n % HM 2-15 HM-2-15 Standard dal gauge holder for PMK-NO-2 Long varant 15 mm length, dameter 8 mm H7, delvered wth M6 x.75 mm thread. Order no.: HM-2-15 Dal gauge holder HEXACON M6 x.75 mm thread M6x.75 dal gauge holder RS 1-2 Thread reducer RS-1-2 Thread reducer for the use of measurng heads wth M3.5x.35 mm thread on HM-2 holders or VL- 2 extenson wth M6x.75 mm thread. Order no.: RS Page 61

62 Standard dal gauge holder Dal gauge holder for PMK-3 meas. heads Mx1 thread Wth ø 8H7 dal gauge connecton and knurled screw. Mx1 mm thread HM 3-GS- Dal gauge holder NEW! HM-3-GS- Standard dal gauge holder for PMK-NO-3 Short, round varant mm length, dameter 15 mm, delvered wth Mx1 mm thread and knurled screw. The Ø 8 mm H7 standard dal gauge shaft s sutable for all types of analog and dgtal dal gauges and nductve measurng probes. Order no.: HM-3-GS- HM 3- Dal gauge holder HM-3- Standard dal gauge holder for PMK-NO-3 Short varant mm length, SW 22 mm, delvered wth Mx1 mm thread and knurled screw. The Ø 8mm H7 standard dal gauge shaft s sutable for all types of analog and dgtal dal gauges and nductve measurng probes. HEXACON Order no.: HM-3- HM 3-15 Dal gauge holder HM-3-15 Dal gauge holder Normal varant 15mm length, SW 22, delvered wth Mx1 mm thread. Dal gauge shaft Ø 8mm H7. Order no.: HM-3-15 HEXACON Page 62

63 Dal gauge holder to hold analog or dgtal dal gauges and nductve measurng probes wth standard 8H7 connecton on precson measurng heads wth Mx1 mm thread. All Hexacon dal gauge holders are fabrcated of hgh-qualty steel. The model HM-3-15 and HM-3-15-RO are fabrcated of temperature-stable precson steel! Thread reducers make t possble to use measurng heads wth smaller threads such as M6x.75 mm or M3.5x.35 mm on holders wth Mx1 mm threads, wth or wthout drve pn. Temperaturestable! Hgh Precson - Made n % HM 3-15-RO Dal gauge holder Rotatng PMK specal holder: For measurng roundness, ovalty, or (wth the 3-pont PMK) polygonal error on fxed, clamped or heavy workpeces. Rotatng head to hold measurng heads. Rotaton s possble through 3. The dal gauge remans statonary n the feld of vson whle turnng. Order no.: HM RO HEXACON Dal gauge holder for Mx1 RS 1-3 Thread reducer RS 2-3 Thread reducer RS 2-3-L Thread reducer RS-1-3 Thread reducer for the use of measurng heads wth M3.5x.35 mm thread on HM-3- holders. RS-2-3 Thread reducer for the use of measurng heads wth M6x.75 mm thread on HM-3- holders. RS-2-3-L Thread reducer for the use of measurng heads wth M6x.75 mm thread on HM-3 holders or VL-3 extenson 5 mm or longer wth drve pn and Mx1 mm thread. Order no.: RS Order no.: RS Order no.: RS L Page 63

64 Specal dal gauge holder Dal gauge holder for heavy or robust dal gauges Wth ø 8H7 dal gauge connecton. Wth adjustng nut M6 x.75 mm thread HA V2 Dal gauge holder HEXACON HA-V2 Holder for heavy or robust dal gauges By adjustng the adjustng nut (G), the dal gauge can easly be adjusted. No awkward handlng. Order no.: Thread (G) Length HA - V2 - K M6 x.75 mm mm HA - V2 - L M6 x.75 mm 1 mm HA V3 Dal gauge holder HEXACON HA-V3 Holder for heavy or robust dal gauges By adjustng the adjustng nut (G), the dal gauge can easly be adjusted. No awkward handlng. Order no.: Thread (G) Length HA - V3 - K Mx1 mm mm HA - V3 - L Mx1 mm 1 mm Page 64

65 PMK specal dal gauge holder for holdng heavy dal gauges and nductve measurng probes. Sutable for precson measurng heads wth M6x.75 mm or Mx1 mm threads. Wth standard 8H7 connecton. The adjustng nut permts the comfortable, effcent adjustment of dal gauges and measurng probes. Pr Hgh e s cs on M a d e n G The holders are made of steel, and the housng of alumnum. Hgh Precson - Made n % rm e y Holder for nductve probes Wth adjustng nut, ø 8H7 dal gauge connecton. M6 x.75 mm thread HT V2 Holder for nductve probes HEXACON HT-V2 Holder for nductve measurng probes By adjustng the M6x.75 adjustng nut (G), the dal gauge can easly be adjusted. No awkward handlng. L=1 mm. Wth knk protecton. Order no.: HT-V2 Specal dal gauge holder HT V3 Holder for nductve probes HT-V3 Holder for nductve measurng probes By adjustng the Mx1 adjustng nut (G), the dal gauge can easly be adjusted. No awkward handlng. L=1 mm. Wth knk protecton. Order no.: HT-V3 HEXACON HT-V2 / HT-V3 Holder wth PMK measurng head and nductve probe. Applcaton example Page 65

66 Centerng holders ZH-PMK Centerng holders for automated measurement Wth 8mm/H7 dal gauge connecton and M6x.75 mm or Mx1 mm thread. Wth adjustng nut ZH PMK-2-13 ø 13 mm M6 x.75 mm thread ZH-PMK-2-13 Centerng holder wth M6x.75 thread for automated measurement, ø 13 mm, length 57 mm. Axal freedom of movement ±.5 mm, clampng rng wth Allen screw. Order no.: ZH-PMK-2-13 M6x,75 ø13 -,5 ±,5 6,5 Adjustng nut Lockng nut 8H7 ZH PMK-2- ø mm M6 x.75 mm thread Adjustng nut ZH-PMK-2- Centerng holder wth M6x.75 thread for automated measurement, ø mm, length mm. Axal freedom of movement ±.5 mm, clampng rng wth knurled screw. M6x,75 8H7 Order no.: ZH-PMK-2-25 ZH PMK-3- ø mm Adjustng nut ZH-PMK-3- Centerng holder wth Mx1 thread for automated measurement, ø mm, length mm. Axal freedom of movement ±.5 mm, clampng rng wth knurled screw. Mx1 8H7 Order no.: ZH-PMK-3-25 Page 66

67 Centerng holder for automated measurement compensate for axal errors n centerng of the workpece and prevent damages to both the measurng head and the measurement object. The axal freedom of movement s ±.5 mm. The set nut fastens the play once adjusted. Avalable wth M6x.75 mm or Mx1 mm threads. Thread reducers make t possble to use measurng heads wth smaller threads such as M6x.75 mm or M3.5x.35 mm on holders and float holders wth Mx1 mm threads. Pr - Made Precson n Hgh e s cs % on y M a d e rm n G e ZH PMK-3- ø mm ZH-PMK-3- Centerng holder wth Mx1 thread for automated measurement, ø mm, length 65 mm. Axal freedom of movement ±.5 mm, clampng rng wth knurled screw. Mx1 SW13 Adjustng nut 8H7 Centerng holder Order no.: ZH-PMK Applcaton examples HEXACON,1mm 5 5 TOL ON / OFF SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS ZH-PMK-3- Centerng holder wth cylndrcal PMK measurng head and analog precson ndcator. ZH-PMK-3- Centerng holder wth chamfered measurng head and analog specal dal gauge. ZH-PMK-3- Centerng holder wth concal PMK measurng head and dgtal dsplay wth factor settng. Page 67

68 Centerng holders ZH-PMK-VDS Centerng holders for automated meas. M6x.75 mm or Mx1 mm threads. Wth twst protecton ZH PMK-2-VDS ø 13 mm NEW! M6 x.75 mm thread M6x,75 Adjustng nut ZH-PMK-2-VDS-13 Centerng holder for automated measurement, wth M6x.75 mm thread, ø 13 mm, length 57 mm. Axal freedom of movement ±.5 mm, clampng rng wth Allen screw. Order no.: ZH-PMK-2-VDS-13 ø 13 -,5 ±, ,5 8H7 ZH PMK-3-VDS ø mm NEW! ZH-PMK-3-VDS- Centerng holder for automated measurement, wth M6x.75 mm thread, ø mm, length mm. Axal freedom of movement ±.5 mm, clampng rng wth knurled screw. Mx1 -,5 ±,5 SW12 Lockng nut Adjustng nut 8H7 Order no.: ZH-PMK-3-VDS Fxng screw ZH PMK-3-VDS ø mm NEW! Mx1 SW13 Lockng nut Adjustng nut ZH-PMK-3-VDS- Centerng holder for automated measurement, wth M6x.75 mm thread, ø mm, length 65 mm. Axal freedom of movement ±.5 mm, clampng rng wth knurled screw. -,5 ±,5 8H7 Order no.: ZH-PMK-3-VDS Fxng screw Page 68

69 Centerng holder for automated measurement compensate for axal errors n centerng of the workpece and prevent damage to both, the measurng head and the measurement object. The twst protecton prevents the dsplay from twstng when the workpece rotates. The axal freedom of movement s ±.5 mm. The set nut fastens the play once adjusted. Avalable wth M6x.75 mm or Mx1 mm threads. Thread reducers make t possble to use measurng heads wth smaller threads such as M6x.75 mm or M3.5x.35 mm on holders and float holders wth Mx1 mm threads. Pr - Made Precson n Hgh e s cs % on y M a d e rm n G e VDS centerng holder Applcaton examples HEXACON,1mm 5 5 TOL ON / OFF SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS ZH-PMK-3-VDS- Center. holder wth cylndrcal PMK meas. head and analogue precson ndcator. ZH-PMK-3-VDS- Center. holder wth chamfered meas. head and analogue specal dal gauge. ZH-PMK-3-VDS- Center.holder wth concal PMK measurng head and dgtal dsplay wth factor settng. Page 69

70 rm Centerng holders Mountng flange ZH-LKM PMK centerng holders B ZH LKM-3-5 Centerng holder Pr - Precson Made n Hgh e s cs on M a d e n G e ZH-LKM-3-5 centerng holder, for mountng n automatc feed unts, avalable wth ZH-FL mountng flange for nstallaton n system parts and ar measurng heads. Other functons and dmensons lke the ZH-PMK-3-5-L centerng holder. Order no.: ZH - LKM % y Open drllng n front ZH MFL Mountng flange Mountng flange ZH-MFL mountng flange, for holdng of ZH-LKM-3-5 centerng holder. Specfy D, d, and B when orderng. Order no.: ZH - MFL B Page 7

71 ZH PMK-3-5-L Centerng holder 1) Connecton thread for measurng head 2) Proxmty swtch for return sprng dstance montorng Pr - Precson Made n Hgh e s cs % on y M a d e rm n G e 3) Ar connecton (cleanng ar connecton) 4) Adjustng nut for float range 5) Housng 6) Rubber sleeve 7) Sprng for weght compensaton 8) Set screw for sprng 9) RF reference surface for (2) Mx1 1 Range Housng 5 Proxmty swtch 2 3 Ar connecton Ø 8H7 Probe connecton Rubber sleeve 6 Sprng 7 Set screw 8 Adjustng nut 4 Reference surface 9 Centerng holder ZH-PMK-3-5-L centerng holder, used for automated measurement n the horzontal as well as vertcal range. Horzontal use The replaceable sprngs (7) can be used wth the set screw (8) to exert the requred compensatng pressure on the ZH-PKM axs. They are adjusted wth the PMK screwed nto place n the horzontal orentaton and the screw pontng down (1 ). Vertcal use In vertcal operaton, the sprng (7) must be removed and the screw (8) screwed n to about.5mm under the Ø housng (5). Adjustment of the orentaton of the ZH-PMK axs to the workpece axs s done as follows: The adjustng nut (4) wth ts concal sde s screwed onto the counter cone n the clockwse drecton untl t stops. After placement tghten another 1-2 full turns. Now set up! Durng operaton, loosen agan and adjust the centerng and/or floatng range (see D). Adjustng the centerng and/or floatng range. The centerng range s set by adjustng the adjustng screw (4) n the play of the cone (radally), max. 1.5 ±.75 mm. The counter screw (4) s used to secure the nut by tghtenng t lghtly. Warnng! Do not tghten the screws for the bush (2). Protecton from destructon and overrun In case of a crash, the axs sprngs back nto the housng (5) by at most 12mm. Along the correspondng return sprng offset, the nut (4) also lfts from the reference surface (n the crcle (RF)) to the back. By usng an electronc probe n (2), the automatc feed movement can be nterrupted. Ths applcaton also can be used for depth measurement. To clamp the probe, 3 bushngs (2) are provded. Clamp probe n bushng (2). Mountng the measurng probe In the Ø8H7 probe connecton (), the measurng probe s fastened after prevously mountng the measurng head n roughly the mddle hysteress range. Note: The PMK should be n the settng master. Ar connecton The ar connecton (3) (Festo system) s only used to connect to cleanng ar that flows over the measurng ponts on the PMK. Dependng on the stuaton, the cleanng ar can mprove condtons at the measurement pont, workpece, servce tme, prelmnary cleanng, etc. Other varant: In a slghtly modfed form, the ZH-PMK-5 seres can also be used for (pure) ar measurng heads. Order no.: ZH-PMK-3-5-L Page 71

72 Modular measurng systems Ø8H7 Dal gauge holders for custom setup, wthout drve needle. For clampng, glung, or screw fastenng. Modular measurng systems Mechansm setup HEXACON Made n,1 mm ,6,4 9,4,2,6,8 1 9,2, MB-DR-25 MB-GS-5 MB- MB DR Dal gauge holder MB GS Dal gauge holder MB Dal gauge holder 8H7 Ø8H7 Ø8H7 -,3 SW14 15 L M12x1 SW14 15 L -,3 L MB-DR Dal gauge holder for clampng for holdng dal gauges and nductve measurng probes. Order no. Length Order no. Length MB-DR-25 25mm MB-DR- mm MB-DR-5 5mm MB-DR-75 75mm MB-DR- mm MB-GS Dal gauge holder for screw fastenng to hold dal gauges and nductve measurng probes. Order no. Length Order no. Length MB-GS-25 25mm MB-GS- mm MB-GS-5 5mm MB-GS-75 75mm MB-GS- mm MB Dal gauge holder for clampng for holdng dal gauges and nductve measurng probes. Order no. Length Order no. Length MB- mm MB-25 25mm MB- mm MB-5 5mm MB-75 75mm MB- mm Page 72

73 The modular measurng system offers helpful elements for the desgner. n the measurng setup. The varety of types for screw or adhesve fastenng, wth or wthout stop, can be used for many applcatons. The holders are provded by default wth a clampng rng wth Allen screw SW 2,5 mm. Startng from a length of mm they are also avalable wth double clampng rngs or knurled screw M3. Pr - Made Precson n Hgh e s cs % on y M a d e rm n G e MB KS-RS Clampng rng MB KS Clampng rng MB RS-M3 Knurled screw SW 2, Ø8H7 Ø8H7 M3 MB-KS-RS Clampng rng wth knurled screw Note: The standard holder has only one clampng rng! MB-KS Clampng rng wth Allen screw SW 2,5 mm Note: The standard holder has only one clampng rng! MB-RS-M3 Knurled screw M3 Note: The standard holder has only one clampng rng! Order no.: MB-KS-RS Order no.: MB-KS Order no.: MB-RS MB KS-2 Double clampng rng HM 2-32 Dal gauge holder Ø8H7 Ø8H SW t = 7 Ø Ø8 M6x,75 MB-KS-2 Double clampng rngs wth Allen screw, SW 2,5 mm Note: The standard holder has only one clampng rng! Order no.: MB--KS-2 HM-2-32 Standard dal gauge holder wth knurled screw, 32 mm length, ø mm, delvered wth M6 x.75 mm thread. Standard dal gauge shaft. Ø 8mm/H7. Order no.: HM-2-32 Page 73

74 Depth extensons Extensons for dal gauge holders wth drve needle M6x.75 mm and Mx1 mm threads. Up to 25 mm n length Extensons of mm and up temperature-stable VL Depth extenson M6 x.75 thread VL Standard depth extenson for PMK-NO-2 Short, round varant mm to 65 mm n length, ø 7.5 mm, delvered wth M6 x.75 thread. Length Order no. mm VL mm VL mm VL mm VL mm VL VL 2 Depth extenson M6 x.75 thread VL - 2 Standard depth extenson for PMK-NO-2 Short, round varant mm to 65 mm n length, ø 8 mm, delvered wth M6 x.75 thread. Length Order no. mm VL-2- mm VL-2- mm VL-2-5 mm VL mm VL-2-65 VL 2 Depth extenson M6 x.75 thread VL - 2 Temperature-stable depth extenson for PMK-NO-2 Varant from to 25 mm n length, dameter 8 mm, delvered wth M6 x.75 thread. Length Order no. mm VL-2- mm VL mm VL mm VL mm VL-2-25 Page 74

75 Hgh Precson - Made n Depth extensons for measurement of deep holes from mm to 25 mm length. Model VL-2 wth M6x.75 mm thread s sutable for all PMK-2 measurng heads and holders n HM-2 sze - M6x,75 mm. Model VL-3 wth Mx1 mm thread s sutable for all PMK-3 measurng heads and holders n HM-3 sze - Mx1 mm. Multple extensons can be combned. Lengths up to 65 mm are fabrcated from tool steel. For lengths of mm and up, we use exclusvely temperature-stablzed steel. Ths nfluences the measurement result from for example the heat of hands only to a very slght extent. The drve pn s fabrcated from hardened steel. Temperaturestable! Thread reducers permt the use of measurng heads wth smaller threads on larger holders and extensons. % VL 3 Depth extenson Length Order no. 5 mm VL mm VL-3-65 VL - 3 Standard depth extenson for PMK-NO-3 Short varant 5 mm length, ø 15 mm, delvered wth M x.1 mm thread. Depth extensons VL 3 Depth extenson Length Order no. mm VL-3- mm VL mm VL mm VL mm VL-3-25 VL - 3 Temperature-stable depth extenson for PMK-NO-3 Varant from to 25 mm n length, ø 15 mm, delvered wth M x.1 mm thread. Mx1 mm thread VL-2 Depth extenson wth M6x,75 mm thread mm and up mm and up VL-2 Depth extenson Mx1 mm thread Page 75

76 Angle extensons PMK WS angle peces for PMK measurng heads Wth M6x.75 mm or Mx1 mm threads. Modular system WS - 2 Angle pece M6 x.75 mm thread WS-2 9 angle pece for PMK-2 wth M6x.75 mm thread. square body. 12 mm wrench sze. Can be combned wth HM-2 measurng gauge holder. Can be combned wth VL-2 depth extensons. Orderng example: WS - 2 WS - 3 Angle pece WS-3 9 angle pece for PMK-3 wth Mx1 mm thread. Hexagonal body. 17 mm wrench sze. Can be combned wth HM-3 measurng gauge holder. Can be combned wth VL-3 depth extensons. Can be combned wth GS devce stands. Can be combned wth TA depth stops. Thread reducer Mx1 to M6x.75 Orderng example: WS - 3 WS SO-2 PMK and angle pece M6 x.75 mm thread WS-SO-2 9 angle pece wth PMK-2 meas. head wth M6x.75 mm thread. Square body, 12mm wrench sze PMK-2 measurng head and angle pece are delvered as an ntegrated unt. L depends on the ndvdual varant. Cannot be unmounted. Orderng example: WS SO Mn. 5 L Page 76

77 Angle peces WS for PMK measurng heads n the modular system, also for use n devce stands. As hand-held measurng nstruments, they are used to mprove readngs n dffcult-to-reach measurement postons. Combnaton opton: Can be combned wth VL depth extensons. Combnaton opton: Can be combned wth GS devce stands. (n combnaton wth VL depth extensons) Pr - Made Precson n Hgh e s cs on M a d e rm n G e Combnaton opton: Can be combned wth TA depth stops. (n combnaton wth VL depth extensons) % y WS SO-3 PMK and angle pece WS-SO-3 9 angle pece wth PMK-2 meas.head wth Mx1 mm thread. Hexagonal body, 17 mm wrench sze PMK-3 measurng head and angle pece are delvered as an ntegrated unt. L depends on the ndvdual varant. Cannot be unmounted. Angle peces Orderng example: WS SO X Mn. 75 L Thread reducers RS 1-2 Thread reducer RS-1-2 thread reducer For the use of measurng heads wth M3.5x.35 mm thread on HM-2 holders. WS-3 angle extenson wth GS devce stand, VL-3 depth extenson and TA-3 depth stop n modular system. TIPP! Order no.: RS RS 1-3 Thread reducer RS 2-3 Thread reducer RS 2-3-L Thread reducer RS-1-3 thread reducer for the use of measurng heads wth M3.5x.35 mm thread on HM-3- holders. RS-2-3 thread reducer for the use of measurng heads wth M6x.75 mm thread on HM-3- holders. RS-2-3-L thread reducer for the use of measurng heads wth M6x.75 mm thread on HM-3 holders or VL-3 extenson 5 mm or longer wth drve pn and Mx1 mm thread. Order no.: RS Order no.: RS Order no.: RS L Page 77

78 Depth stop clampng rngs TA-KR Depth stops for PMK measurng heads Permts measurements n defned hole depths. Adjustable TA-KR-V depth stop clampng rng. The adjustable steel Hexacon depth stop clampng rngs are specally fabrcated to ft the ndvdual dmensons of your PMK and are mounted on the body of the PMK measurng head. Ther poston on the measurng head s varably adjustable to permt measurements at defned hole depths. Inner bore and flat surface are fabrcated n a sngle clampng step. The back s marked wth a V notch. Measurement errors due to the tlt effect durng measurement are avoded by precson gudng at a rght angle. Clampng rngs represent an easy-to-use, robust, flexble soluton as an adjustable depth stop. The clampng rngs are fabrcated of burnshed, unhardened steel. Standard nner dameters are avalable from 6-85 mm. Other dmensons upon request. The nner bore s about.1mm less than the nomnal dameter of the measurng head. TA-KR-V Depth stop clampng rng NEW! b Pr Made - n Precson Hgh e s cs % on M a d e rm n G e y Adjustable TA-KR-V depth stop clampng rng d1 (mm) d2 (mm) b (mm) d1 (mm) d2 (mm) b (mm) Page 78

79 Depth stops TA-2 depth stops for PMK-2 measurng heads Bell form Permts measurements n defned hole depths. Adjustable TA 2-45 Depth stop bell TA 2-75 Depth stop bell TA 2-45 Depth measurng NEW! For VL-2 extenson NEW! For VL-2 extenson NEW! Example applcaton: ø 8H7 ø 8H7 9 9 HEXACON,1 mm Made n ø 75 ø ø d ø 24 ø d ø 24 TA-2-45 depth stop can be clamped to VL-2 extenson Specfy nner dameter when orderng. Order no.: TA-2-45 TA-2-75 depth stop can be clamped to VL-2 extenson Specfy nner dameter when orderng. Order no.: TA-2-75 TA-2-45 as depth measurng head wth serveral dal gauges and dal gauge extensons on request. Order no.: TM-2-45 TA-2 depth stop bell form The adjustable Hexacon depth stops can be clamped on VL-2 depth extensons. Ther poston on the extenson s varably adjustable to permt measurements at defned hole depths. Measurement errors are also prevented by the precson gudng at a rght angle. Depth stops represent an easy-to-use, robust, flexble soluton as an adjustable depth stop. The clampng rngs are fabrcated of unhardened steel. Lengths from mm are avalable. Pr Hgh e s cs on Other dmensons upon request. Hgh Precson - Made n M a d e n G % y rm e Page 79

80 Depth stops Depth stops for hole measurng heads n a modular system Can be combned wth dfferent extenson arms and GS devce stand. TA - 3 Depth stops Base body Short extenson arm Long extenson arm Depth stops n the modular system. The TA-3 base body can be converted usng the TA-3-A1 and TA-3-A2 extenson arms to support larger arcs from ø 28 mm to 15 mm. Depth stops for PMK, can be clamped to: - HM holder VL extenson - 3 Order no.: TA Base body - ø TK 28-5 mm TA A1 - Short extenson arm - ø TK - mm TA A2 - Long extenson arm - ø TK 1-15 mm Page

81 Hgh Precson - Made n % Depth stops n a modular system permt flexble applcatons for measurng workpeces at a defned depth, both at through holes, near the bottom of the hole, and n blnd holes. The hexagonal TA-3 base body as three arc dameters of ø 28 mm, ø mm, and ø 5 mm and can be clamped and adjusted on the HM-3-15 holder and the VL-3 extensons n lengths from 5 to 255 mm. Three ncluded spacer bolts are screwed nto the base body at one of the three dameters and hold the measurement object at the optmum dstance. The TA-3-A1 and TA-3-A2 extenson arms can be used to extend the hole dameter flexbly from ø - mm and ø 1-15 mm. VL 3 Depth extenson VL-3-65 Extenson HM-3-15 Holder Depth stops Length: Order no.: 5 mm VL mm VL-3-65 Temperature-stable steel ø from mm Length: Order no.: mm VL-3- mm VL mm VL mm VL mm VL-3-25 Temperaturstabl! Page 81

82 Devce stands WS-3 angle pece GS devce stands - for the seres meas. of compact workpeces Up to 6 stands can be combned. GS PMK-1 Devce stand TIPP! Techncal data: Workpece Ø: max. 17 mm Workpece heght: max. 2 mm L x W x H: about x 15 x 5 mm Order number: GS-PMK-1 HM-3-GS- dal gauge holder can be combned wth the GS devce stand. Gauge dsplay here s n the horzontal orentaton. GS PMK-4 Devce stands Extensble to up to 6 ponts! GS-4 devce stand: The GS devce stand can be extended upon request to up to 6 measurement ponts. Page 82

83 GS devce stands for PMK measurng heads. The use of the devce stand smplfes handlng sgnfcantly durng statonary measurement. The combnaton of holders, extensons, angle peces, and depth stops permts ndvdual, flexble applcatons for the ratonal measurement of smaller parts. The devce stand for PMK can be extended to up to 6 ponts! Extenson wth multple stands elements nto one unt permts measurements wth dfferent measurng heads n one compact measurng stand unt. Pr - Made Precson n Hgh e s cs % on y M a d e rm n G e Devce stands Applcaton example Applcaton example WS-3 angle pece, wth VS-3 depth extenson and HM-3- dal gauge holder completes the GS-PMK devce stand. VL-3 depth extenson wth TA-3 depth stop, WS-3 angle pece and HM-3- dal gauge holder round out the devce stand to form a comfortable measurng staton. Dal gauge n vertcal orentaton. Page 83

84 TOL SET TOL ON / OFF PRESET DATA RESET SETPR MENU ABS Measurement stands Measurement stands sutable for larger workpeces permts effectve seres hole measurement and chamfer measurement. UMS - 1 Measurement stand TIPP! ABS mm Specal varants: Longer measurement columns as well as modfed drves are possble. Ceramc measurement table upon request. ZH-PMK-3- meas. gauge holder Centerng holders smplfy the centered nserton of the measurng head nto the workpece. UMS-1 unversal measurement stand Order number: UMS - 1 The UMS-1 s perfect for measurement tasks on larger workpeces. Smple handlng s possble n combnaton wth our precson measurng heads and chamfer measurng heads. Dal gauge holders or floatng holders to hold mechancal or electronc dstance sensors can be ncluded. Techncal data: Workpece Ø: max. 17 mm Workpece heght: max. 2 mm L x W x H: about x 15 x 5 mm Page 84

85 HEXACON,1mm UMS-2 unversal measurement stand The UMS-2, n combnaton wth the dfferent PMK measurng heads, s perfect for measurements n the µ range. The fully new concept of the measurement axs n the feed axs wth the ntegrated centerng holder largely elmnates measurement and angle errors due to unloadng. The centerng holder (ncluded standard) can be blocked or released for radal floatng. The stable, rgd desgn also permts relable depth measurement. UMS - 2 Measurement stand 5 5 Measurement stands Standard accessory: Measurement table Ø 125 mm Centerng holder wth floatng axs compensaton. Depth stop to lmt measurement depth. Interchangeable stand head for other stands. Ceramc measurng table upon request. Workpece Ø max. 1 mm Order number: UMS - 2 Techncal data: Workpece Ø: max. 1 mm Workpece heght: max. 1 mm Measurng head holder: M x 1 /M6 x.75 Weght about kg Page 85

86 Adjustment rngs Adjustment rngs wth nomnal DIN 225 C standard dmensons. Adjustment rngs complant wth DIN 225 C standard dmensons Adjustment rngs / control rngs made of frst-class gauge steel, hardened, tempered, grounded and fnely lapped. The adjustment rngs are labeled wth the actual dm. Tolerance for the hole s JS4. Adjustment rngs DIN 225-C Page 86

87 Chamfer measurement Functonal prncple of chamfer measurement Exteror chamfer measurng Dsplay resoluton.1 mm Precson nteror and exteror chamfer measurng nstruments wth ttanum ntrde coatng. - Precson Made n Hgh Prec TN COATED 2 HV % on - Made n We offer nteror and exteror chamfer measurng nstruments wth measurng angles of 9, and 127 n standard varants. They are sutable for quck precson measurement of chamfers, depressons and holes, both for one-tme measurement or for seres measurement. Specal dal gauge Dsplay 1:2 Measurng head nterchangeable Measurng outsde dameter of chamfer Connecton ø 8mm H7 Holder nterchangeable Standard thread ø M x 1 Rubber protecton Housng Measurng angle 9 TN coated Workpece Ther wde measurng range of up to mm s a great advantage. In ther purely mechancal measurng prncple, the measurng cone probes the chamfer, depresson or hole and drects the force wthn the housng onto a hardened, ground drve needle and then to the dsplay. A dal gauge holder connects the measurng head to correspondng dsplays such as analog or dgtal dal gauges, nductve measurng probes, measurng columns, or automated computer measurng systems. The removable HM-3- dal gauge holders are ncluded n the standard scope of delvery and permt the flexble handlng of dfferent measurng heads. For example, at 9 measurng angles, measurng heads of dfferent szes as well as nteror and exteror measurng heads can easly be swapped whle stll usng the same holders, gauges, or measurng systems. The qualty-mprovng ttanum ntrde coatng, wth hgh hardness values - about 2 HV - and outstandng sldng and frcton characterstcs, s ncluded n the standard scope of delvery at no extra cost. It gves our precson metrology equpment ts outstandng servce lfe. Other measurng angles upon request. Chamfer dameter All Hexacon metrology equpment % Made n The specal dal gauges wth 1:2 dsplay scale for 9 measurng angles convenently show the sze of the outer dameter of the chamfer drectly n mllmeters! That elmnates converson and readng errors. The dal gauges are equally sutable for ether nteror or exteror measurement. We offer these specal dal gauges for precson measurng heads wth dameters from.5 to mm, each wth a mm measurng range. The specal analog dal gauge wth 1/ mm dsplay accuracy and a mm measurng range s ncluded n the standard scope of delvery wth all 9 measurng heads! TIPP! Page 87

88 Chamfer measurng 9 Interor chamfer measurng nstruments for 9 chamfers Standard varant ncludng holder and gauge. Measurng range mm 9 Prncple: Cone FM SB-1 9 Ø.5 - mm FM SB-2 9 Ø - mm The specal dal gauge dsplays the result of the chamfer drectly n mm! Measurng range.5- mm 1 1 HEXACON 1 1 Made n,1 mm HEXACON HEXACON 1 Clampng shaft Ø 8h7mm The specal dal gauge dsplays the result of the chamfer drectly n mm! 1 1 HEXACON 1 1 Made n,1 mm Measurng range - mm 1 XACON HEXACON 1 Clampng shaft Ø 8h7mm Precson nteror chamfer measurng nstrument wth ttanum ntrde coatng. Interor chamfer measurng nstruments wth a 9 measurng cone quckly and accurately measure the largest dameter of chamfers, depressons and holes. Ther measurng accuracy s.1 mm. The specal analog dal gauge ncluded, wth ts 1:2 scale dvson, shows the result of the largest chamfer dameter drectly n mm wth no converson needed. The dsplay accuracy s.1 mm. The specal dal gauge s sutable for nteror or exteror cone measurng nstruments wth 9 measurng angles. The HM-3- dal gauge holder, also ncluded, s removable to permt ts use and combnaton wth other components n our accessory lne. Partcularly convenent s not only the large measurng range of about mm, but also the long servce lfe of the measurng head thanks to the ttanum ntrde treatment. Dal gauge ncluded Dal gauge ncluded Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø.5-9 FM-SB-1 Ø - 9 FM-SB-4 Ø - 9 FM-SB-2 Ø - 9 FM-SB-5 Ø - 9 FM-SB-3 Ø FM-SB-6 The specal dal gauge s ncluded n the standard scope of delvery up to a mm dameter! The dal gauge holder s always ncluded n the delvery. The specal dal gauges and holders are dentcal for nteror and exteror measurement of the same sze at 9, and the measurng heads are nterchangeable. TIPP! Page 88

89 Precson exteror chamfer measurng nstrument wth ttanum ntrde coatng. Standard exteror chamfer measurng nstruments wth 9 measurng angles are used for quck precson measurement of the dameter of exteror chamfers and shaft ends. Ther wde measurng range of about mm s a great advantage. For all 9 varants up to a dameter of mm, the measurng head, specal dal gauge and dal gauge holder are provded together as a kt! For larger dameters, we recommend dgtal dal gauges wth a factor settng. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Exteror chamfer measurng nstruments for 9 chamfers Standard varant ncludes holder and analog gauge. Prncple: 45 Bell FM FB-1 9 Ø 5 - mm FM FB-4 9 Ø - mm The specal dal gauge dsplays the result of the chamfer drectly n mm! Measurng range.5- mm 1 1 HEXACON 1 1 Made n,1 mm XACON HEXACON 1 Clampng shaft Ø 8h7mm For larger dameters of over mm, we recommend dgtal dal gauges wth a factor settng! Dal gauges wth a factor settng! TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU ABS Clampng shaft Ø 8h7mm Dgtal dal gauge not ncluded n scope of delvery. Chamfer measurng 9 o Dal gauge ncluded Dal gauge not ncluded Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø 15-9 FM-FB-1 Ø - 9 FM-FB-4 Ø - 9 FM-FB-2 Ø - 9 FM-FB-5 Ø - 9 FM-FB-3 Ø FM-FB-6 Exteror chamfer measurng For comparatve measurements a reference workpece or confguraton master s requred! Page 89

90 Chamfer measurng Interor chamfer measurng nstruments for chamfers Standard varant ncludng holder. Measurng range mm Prncple: Cone FM SA-1 Ø.5-12 mm FM SA-4 Ø - 41 mm The HM-3- dal gauge holder s ncluded! TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU ABS Dal gauges wth a factor settng! NEW! The HM-3- dal gauge holder s ncluded! TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU ABS Dal gauges wth a factor settng! NEW! Precson nteror chamfer measurng nstrument wth ttanum ntrde coatng. Interor chamfer measurng nstruments wth a 9 measurng cone quckly and accurately measure the largest dameter of chamfers, depressons and holes. Ther measurng accuracy s.1 mm. The specal analog measurng gauge wth 1:2 scale dvsons dsplays the results of the largest chamfer dameter drectly n mllmeters. The dsplay accuracy s.1 mm. The specal measurng gauge s sutable for both nner or outer dameters HEXACON HEXACON Dal gauge not ncluded Dal gauge not ncluded The HM-3- dal gauge holder, also ncluded, s removable to permt ts use and combnaton wth other components n our accessory lne. Partcularly convenent s not only the large measurng range of about mm, but also the long servce lfe of the measurng head thanks to the ttanum ntrde treatment. Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø.5-12 FM-SA-1 Ø - 71 FM-SA-7 Ø - 21 FM-SA-2 Ø 7-81 FM-SA-8 Ø - 31 FM-SA-3 Ø - 91 FM-SA-9 Ø - 41 FM-SA-4 Ø 9-1 FM-SA- Ø - 51 FM-SA-5 Ø FM-SA-11 Ø 5-61 FM-SA-6 Ø FM-SA-12 The dal gauge holder s always ncluded n the delvery. The specal dal gauge s not ncluded! TIPP! Page 9 The specal dal gauges and holders are dentcal for nteror and exteror meas. of the same sze at, and the measurng heads are nterchangeable.

91 Precson exteror chamfer measurng nstrument wth ttanum ntrde coatng. Standard exteror chamfer measurng nstruments wth measurng angles are used for quck precson measurement of the dameter of exteror chamfers and shaft ends. Ther wde measurng range of about mm s a great advantage. For all varants we recommend dgtal dal gauges wth a factor settng. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Exteror chamfer measurng nstruments for chamfers Standard varant ncludes holder. Prncple: Bell FM FA-1 Ø 5-12 mm FM FB-4 Ø - mm For all varants we recommend dgtal dal gauges wth a factor settng. TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU ABS NEW! Dal gauges wth a factor settng! For all varants we recommend dgtal dal gauges wth a factor settng. TOL ON / OFF SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS Dal gauges wth a factor settng! NEW! Chamfer measurng o The HM-3- dal gauge holder s ncluded! HEXACON The HM-3- dal gauge holder s ncluded! HEXACON Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø 5-12 FM-FA-1 Ø - 71 FM-FA-7 Ø - 21 FM-FA-2 Ø 7-81 FM-FA-8 Ø - 31 FM-FA-3 Ø - 91 FM-FA-9 Ø - 41 FM-FA-4 Ø 9-1 FM-FA- Ø - 51 FM-FA-5 Ø FM-FA-11 Ø 5-61 FM-FA-6 Ø FM-FA-12 Exteror chamfer measurng For comparatve measurements a reference workpece or confguraton master s requred. Page 91

92 ,1 mm Made n Chamfer measurng Interor chamfer measurng nstruments for 127 chamfers Standard varant ncludng holder. Measurng range mm Prncple: Cone FM SC Ø.5 - mm FM SC Ø - mm For all127 varants we recommend dgtal dal gauges wth a factor settng. TOL ON / OFF NEW! For all127 varants we recommend dgtal dal gauges wth a factor settng. TOL ON / OFF NEW! HEXACON SET TOL MENU SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS Dal gauges wth a factor settng! ABS mm PRESET DATA RESET SETPR ABS Dal gauges wth a factor settng! Clampng shaft Ø 8h7mm The HM-3- dal gauge holder s ncluded! Clampng shaft Ø 8h7mm The HM-3- dal gauge holder s ncluded! Dal gauge not ncluded Dal gauge not ncluded Measurng stand MS-1 TIPP! Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø FM-SC-1 Ø FM-SC-4 Ø FM-SC-2 Ø FM-SC-5 Ø FM-SC-3 Ø FM-SC-6 Effectve chamfer measurement s possble usng the MS-1 measurng stand along wth the ZH centerng holder. The specal dal gauges and holders are dentcal for nteror and exteror measurement of the same sze at 127, and the measurng heads are nterchangeable. Page 92

93 Precson exteror chamfer measurng nstrument wth ttanum ntrde coatng. Standard exteror chamfer measurng nstruments wth 127 measurng angles are used for quck precson measurement of the dameter of exteror chamfers and shaft ends. Ther wde measurng range of about mm s a great advantage. For all 127 varants we recommend dgtal dal gauges wth a factor settng. - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Exteror chamfer measurng nstruments for 127 chamfers Standard varant ncludes holder. Prncple: 63,5 Bell FM FC Ø 5 - mm FM FC Ø - mm For all 127 varants we recommend dgtal dal gauges wth a factor settng. TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU ABS Dal gauges wth a factor settng! NEW! For all 127 varants we recommend dgtal dal gauges wth a factor settng or nductve probes, page 1. NEW! Chamfer measurng 127 o Clampng shaft Ø 8h7mm The HM-3- dal gauge holder s ncluded! Clampng shaft Ø 8h7mm The HM-3- dal gauge holder s ncluded! Dal gauge not ncluded Inductve probe not ncluded Measurng range: Cone: Order no.: Measurng range: Cone: Order no.: Ø FM-FC-1 Ø FM-FC-4 Ø FM-FC-2 Ø FM-FC-5 Ø FM-FC-3 Ø FM-FC-6 Exteror chamfer measurng For comparatve measurements a reference workpece or confguraton master s requred. Page 93

94 Chamfer probe 45 Precson 45 chamfer probe Precse measurement of chamfer wth 45 angles on 9 workpeces. Chamfer sze Chamferangles 45 Length L Measurng range mm 9 Workpece FT chamfer probe Includes dal gauge. The dal gauges have concentrc ndcator arrangement. Measurng accuracy s.1 mm. Measurng range mm 9 9 HEXACON Made n,1 mm H7 5 Dal gauge ncluded NEW! Clampng shaft Ø 8h7mm L We recommend also dgtal dal gauges wth a factor settng. Dal gauges wth a factor settng! Chamfer sze Chamferangles 45 TOL SET TOL ABS ON / OFF mm PRESET DATA RESET SETPR MENU 9 Workpece ABS Dal gauge not ncluded Clampng shaft Ø 8h7mm Length L Determnaton of the chamfer sze Chamfer sze F Length L.1 mm.7 mm.2 mm.14 mm.3 mm.21 mm.4 mm.28 mm.5 mm.35 mm.6 mm.42 mm.7 mm.49 mm.8 mm.57 mm.9 mm.64 mm 1. mm.71 mm 1.5 mm 1.6 mm 2. mm 1.41 mm 2.5 mm 1.76 mm 3. mm 2.12 mm 3.5 mm 2.47 mm The determnaton of the chamfer sze s va the table dsplay L=Chamfer sze F x.771 Chamfer sze F=Length L :.771 The settng or converson factor s FT-1 precson 45 chamfer probe wth ttanum ntrde coatng. Prsmatc measurement prncple. Measures precson chamfers wth 45 angles on 9 workpeces. Dameter mm. Set ncludes dal gauge, dsplay accuracy of 1/mm. Standard dal gauge connecton, dameter 8H7 mm. Can also be combned wth other analog and dgtal dal gauges as well as nductve measurng probes. The specal dal gauge s ncluded n the standard scope of delvery. Order no.: FT-1 ncludng analog dal gauge Order no.: FT-1-X wthout dal gauge. Dgtal dal gauges wth factor settng capablty allow drect dsplay n mm. The settng or converson factor s TIPP! Page 94

95 Chamfer dal gauges Analog mechancal specal precson dal gauges for 9 measurng heads wth a large measurng range of mm. Dsplay scale wth a 1:2 scale Dsplay accuracy.1 mm DIN EN ISO 463 / DIN 874 dal gauge for nteror and exteror chamfer measurement. Measurng range mm. AD FM-1 9 Ø.5 - mm AD FM-2 9 Ø - mm AD FM-3 9 Ø - mm NEW! Scale 1:2 Scale 1:2 Scale 1:2 NEW! NEW! HEXACON,1 mm 1 Made n HEXACON,1 mm 1 Made n HEXACON,1 mm 1 Made n Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm Measurng: Cone: Order no.: Ø 5-9 AD-FM-1 Measurng force.7 N ± % Interor and exteror chamfer meas. Measurng: Cone: Order no.: Ø - 9 AD-FM-2 Measurng force.7 N ± % Interor and exteror chamfer meas. Measurng: Cone: Order no.: Ø - 9 AD-FM-3 Measurng force.7 N ± % Interor and exteror chamfer meas. Analog mechancal specal precson dal gauges for 9 measurng heads wth dsplay scale drectly n mm and a large measurng range. The dal gauges have concentrc ndcator arrangement as well as a dsplay scale wth a 1:2 scale, permttng convenent read-off of the measured value drectly n mllmeters for 9 measurement. Ths elmnates readng errors. The measurng range s about mm and dsplay accuracy s.1 mm. Clampng shaft Ø 8H6 mm. Wth fastenng screw to prevent unntentonal twstng of the scale. Outer rng Ø 58 mm. Threaded measurement tp M2.5. The specal analog dal gauge s already ncluded n the standard scope of delvery for 9 measurng heads! HEXACON ,1 mm Made n NEW! AD FM-4 9 Ø - mm Measurng: Cone: Order no.: Ø - 9 AD-FM-4 Interor and exteror chamfer measurng. Measurng force.7 N ± % Clampng shaft Ø 8h7mm

96 Notes

97 Made n TOL SET TOL,1 mm MENU ON / OFF SETPR PRESET DATA RESET,4,6,2,8 Analog precson ndcators and dal gauges Dgtal dal gauges Dal gauge test stand Inductve probes Analog dal gauges and precson ndcators for hole measurng heads Dal gauge Scale dvson value.1 mm Dal gauge concentrc scale arrangement Scale dvson value.1 mm Precson ndcator Scale dvson value.1 mm Precson ndcator Scale dvson value.1 mm HEXACON Made n,1 mm 9 9,4,2,6,4,6,8,8 1, Dgtal dal gauges for hole meas. heads Dgtal dal gauges Numercal step.1 mm Dgtal dal gauges Numercal step.1 mm ,6 9 9,4,2,8 1 7 TOL ON / OFF SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS Inductve measurng probe, measurng test staton ABS mm Page 97

98 Analog dal gauges Analog dal gauges and precson ndcators for PMK meas. heads as well as other measurement tasks. Dal gauge test tps M2.5 mm thread MU Dal gauge MU 1-1 Meas. range mm MU 2-1 Dal gauge 7 9 HEXACON Made n,1 mm Resoluton.1 mm 9,4,2,6,4,6,8,8 1, Concentrc ndcator arrangement 9 9 HEXACON ,1 mm Resoluton.1 mm Made n 7 Resoluton.1 mm Wth free stroke and collson protecton HEXACON,1mm 5 5 Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm Interor, adjustable tolerance marks NEW! Interor, adjustable tolerance marks NEW! NEW! Scale dvson value.1 mm Measurement span 1 mm 1 ndcator rotaton.2 mm Startng measurng force.7 N ± % Ø 58 mm, DIN EN ISO 463 Scale dvson value.1 mm Measurement span mm 1 ndcator rotaton 1 mm Startng measurng force.7 N ± % Ø 58 mm, DIN EN ISO 463 / DIN 878 Scale dvson value.1 mm Measurement span.1 mm Scale numberng 5--5 Startng measurng force 1. N ± % Ø 62 mm, DIN Analog mechancal precson dal gauges and precson ndcators wth dsplay accuracy of.1 mm and.1 mm. The refned desgn, the use of hgh-qualty materals, and the mature precson-manufactured measurement mechansm guarantee the outstandng qualty of our precson dal gauges and precson ndcators. Measurng bolts and clampng shaft are made of hgh-resstance stanless steel. The measurng bolt s lapped. Clampng shaft Ø 8h7. MU TS-L Meas. nsert for dal gauge HM-meas. nserts for dal gauges. R= 2,5; 4,5; 6,5; L M2,5 R 4,5 Order no.: Specfy MU -TS - L, R MU VL-L Extenson for dal gauge Extensons for dal gauges. Dfferent lengths avalable Order no.: Specfy MU - VL - L, L Page 98 MU TS-L Ball nsert for dal gauge Ball nserts for dal gauges. Dfferent lengths and rad avalable Order no.: Specfy MU - R5 - L, L+R Wth M2.5 thread

99 Dgtal dal gauge Dgtal dal gauge for PMK meas. heads and chamfer meas. nstruments as well as other measurement tasks. MU 5-1 wth factor settng. MU 2-1 Dal gauge MU 4-1 Dgtal dal gauge MU 5-1 Dgtal dal gauge Resoluton.1 mm Resoluton.1 mm Resoluton.1 mm Wth free stroke and collson protecton Wth factor settng 15 5 HEXACON,1mm 5 15 TOL SET TOL MENU ON / OFF , MM SET ABS mm REF l / ll ON / OFF PRESET DATA RESET mm / nch RESET SETPR ABS Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm Clampng shaft Ø 8h7mm NEW! NEW! NEW! Scale dvson value.1 mm Measurement span.5 mm Scale numberng Startng measurng force 1.1 N ± % Ø 62 mm, DIN Numercal step.1 mm Measurement span 12.5 mm Startng meas. force.5-1 N ± % Numerc step value.1 mm wth factor settng Measurement span 12.5 mm Startng meas. force.5-1 N ± % Dgtal mechancal precson dal gauges and precson ndcators wth dsplay accuracy of.1 mm and.1 mm. Hgh-contrast, large, easly readable LCD dsplay, control and dsplay part can turn 2. Lftng cap wth dust protecton functon on end of measurng bolt. Clampng shaft and measurng bolts of hardened stanless steel. Ø 8h7 mm Dal gauges wth nch dsplays are avalable upon request. Page 99

100 Made n TOL SET TOL,1 mm MENU,6,8,4,2 ON / OFF SETPR PRESET DATA RESET Dal gauge test stand Test staton for dal gauges and precson ndcators for analog and dgtal dal gauges based on DIN 878 and DIN 875. DIN 878 DIN 875 MU - PS Dal gauge test stand TOL ON / OFF Pr e s cs on M a d e ,6,4,2, SET TOL MENU ABS mm PRESET DATA RESET SETPR ABS - Made Precson n Hgh % y rm n G e ABS mm Repeat accuracy at IT 8 down to < 1µ. Dal gauge test staton The test staton permts the testng of analog and dgtal dal gauges and precson ndcators usng a calbrate reference gauge or usng nductve measurng probes and a measurement system. By rotatng the set screw, the measurement path and measured value dsplay change, permttng the precson comparson of reference and test object. Test workstaton for dal gauges and precson ndcators. The dal gauge test stand supports the testng of dal gauges and precson ndcators wth a test dstance of up to mm. Permts the testng of dal gauges, precson ndcators and lever gauges for complance wth DIN 878, 875, 227, ASME/ANSIB M 1987, the VDI/VDE DGQ 261 drectves or factory standards. Stand order no.: MU-PS Dsplay and probe order no.: MU-EL Standard delvery wthout dal gauge or nd. meas. probe. Page

101 Inductve measurng probes Inductve measurng probes for PMK measurng heads and chamfer measurng nstruments Inductve measurng probes have very hgh resoluton at a very attractve prce. They also have a long servce lfe and are easly repared. Wth standard 8h6 connecton. TN coated, resoluton.1 µm. IT - 1 Inductve meas. probes Inductve measurng probe Resoluton.1 µm, measurement stroke ± 1 mm, total stroke 4.6 mm. Measurng force.63 N ±% ball gude zero-play Measurement nsert 3 mm ball, M2.5 mm thread, replaceable. Temperature range - to +65 C, easy to repar. Ttanum ntrde coated. Dal gauge tester Order no.: IT-1 IT - 2 Inductve meas. probes Radal cable gude Inductve measurng probe Resoluton.1 µm, measurement stroke ± 1 mm, total stroke 4.6 mm. Measurng force.63 N ±% ball gude zero-play Measurement nsert 3 mm ball, M2.5 mm thread, replaceable. Temperature range - to +65 C, easy to repar. Ttanum ntrde coated. Order no.: IT-2 HT - V2 Inductve probe holder Meas. probes adjustable HT-V2 Holder for nductve measurng probes By adjustng the M6x.75 adjustng nut (G), the nductve probe can easly be adjusted. No awkward handlng. L=1 mm. Wth knk protecton. Order no.: HT-V2 Page 1

102 Example applcatons VL-2 depth extenson M6x.75 VL-3 depth extenson Mx HEXACON 7 Made n,1 mm 7 9 5,4, ,6,4,6,8,2,8 1 TA-2 depth stop adjustable, clamped on VL-2 extenson Accessores n modular system: An extensve offerng of carefully coordnated system accessores such as dal gauge holders, depth extensons, depth stops and centerng holders offer flexble, effcent handlng n a wde varety of measurement tasks, both for manual and for automated measurement. Pr Made n - Precson Hgh e % TA-3 depth stop, adjustable, clamped onto HM-3-GS- holder wth PMK-3-XK measurng head s cs on y M a d e rm n G e Page 2

103 Notes

104 Precson hole and chamfer measurng nstruments - Made Precson n Hgh Prec TN COATED 2 HV % on - Made n Hole measurng nstruments Chamfer meas. nstruments fm-desgn create-com.de Hexacon Messtechnk GmbH Dammweg 35 D-647 Deburg Phone +49 () Fax +49 () Emal: germany@hexacon.net