PRIMERGY ECONEL 30. Operating manual. Introduction. Important notes. Preparing for use. Operation. Troubleshooting and tips.

Transcription

1 Introducton Important notes PRIMERGY ECONEL 30 Preparng for use Operaton Operatng manual Troubleshootng and tps System expansons Techncal data Index November 2002 edton

2 Mcrosoft, MS, MS-DOS, Wndows, and Wndows NT are regstered trademarks of Mcrosoft Corporaton. VESA and DPMS are trademarks of Vdeo Electroncs Standards Assocaton. PS/2 s a regstered trademark of Internatonal Busness Machnes, Inc. Pentum s a regstered trademark of Intel Corporaton, USA. Kensngton Lock and McroSaver are regstered trademarks of ACCO World Corporaton. All other trademarks referenced are trademarks or regstered trademarks of ther respectve owners, whose protected rghts are acknowledged. Copyrght Fujtsu Semens Computers GmbH 2002 All rghts, ncludng rghts of translaton, reproducton by prntng, copyng or smlar methods, n part or n whole, are reserved. Offenders wll be lable for damages. All rghts, ncludng rghts created by patent grant or regstraton of a utlty model or desgn, are reserved. Delvery subject to avalablty. Rght of techncal modfcaton reserved. Ths manual was produced by cogntas. Gesellschaft für Technk-Dokumentaton mbh

3 Contents Your PRIMERGY ECONEL Features...2 Notatonal conventons...3 Target group...3 Important notes...5 Safety...5 Energy savng, dsposal and recyclng...5 CE markng...5 FCC Class B Complance Statement...6 Transportng the server...6 Cleanng the server...6 Preparng for use...7 Unpackng and checkng the delvery...7 Steps for ntal setup...7 Settng up the server...8 Connect the montor, mouse and keyboard...8 Connectng the montor...8 Connectng the mouse...9 Connectng a keyboard...9 Connectng the server to the mans voltage...10 Intal swtch-on: Software wll be nstalled...11 Swtchng on montor and server...11 Installng the software...13 Confguraton wth ServerStart...13 Installaton procedure n ServerStart...14 Guded nstallaton of a sngle server...15 Replcated nstallaton of several servers (Wndows)...17 Connectng external devces...18 Ports on the server...19 Connectng external devces to the seral port...20 Connectng external devces to the parallel port...20 Connectng external devces to the USB port...21 Operaton...23 Swtchng the server on...23 Swtchng the server off...23 Indcators on the server...24 Keyboard...25 Important keys and key combnatons...25 Workng wth floppy dsks...27 Settngs n BIOS Setup...28 Property and data protecton...28 Ant-theft protecton and lead-sealng...28 BIOS setup securty functons...29 A26361-K831-Z

4 Contents Troubleshootng and tps Installng new software Power-on ndcator remans unlt after you have swtched on your devce The screen stays blank No mouse ponter dsplayed on the screen The floppy dsk cannot be read or wrtten Tme and/or date s not correct Error messages on the screen Restorng the hard dsk contents Tps System expansons Informaton about boards...35 Openng the casng Closng the casng Installng and removng a board Installng a board Removng a board Low-Profle boards Mountng slot adapter Removng slot adapter Installng and removng drves Removng the front panel...43 Attachng the front panel Installng an accessble drve Removng an accessble drve Changng the floppy dsk drve Installng or removng the hard dsk drve Extensons to the system board Removng the power supply Upgradng man memory Replacng processor Replacng lthum battery Swngng the power supply n Techncal data Index A26361-K831-Z

5 Your PRIMERGY ECONEL s avalable wth varous confguraton levels wth dfferent hardware and software. In addton, you can nstall accessble drves (e.g. DVD drve), hard dsk drves and other boards. Ths operatng manual tells you how to put your server nto operaton and how to operate t n daly use. Ths descrpton apples for all confguraton levels. Dependng on the confguraton level chosen some of the hardware components descrbed may not be avalable on your server. Please observe the notes on your operatng system. Your server has a number of securty features to ensure that no unauthorzed persons can access your data. The securty functons n the BIOS Setup also allow you to protect your data by means of passwords. In addton, you can also mechancally lock your server. ServerStart allows you under some operatng systems to easly and quckly nstall the latest drvers and operatng system extensons wth a few mouse clcks. Further nformaton on ths server s provded: n the "Safety and Ergonomcs" manual n the "Warranty" manual n the operatng manual for the montor n the techncal manual for the system board n the "BIOS Setup" manual n your operatng system documentaton n the nformaton fles (e.g. *.TXT, *.DOC, *.WRI, *.HLP) Some of the manuals lsted can be found on the "ServerBooks" CD provded wth your server. These manuals can be read and prnted wth Acrobat Reader, also contaned on the CD. Keep ths operatng manual together wth your devce. If you pass on the devce to thrd partes, you should nclude ths manual. A26361-K831-Z

6 Your PRIMERGY ECONEL Features Features Mechancal access protecton Devce for "Kensngton Lock" Eye for padlock or for sealng BIOS-based access protecton System passwords Actvatng and deactvatng nterfaces, ncludng USB Boot and wrte protecton for floppy dsk and hard dsk drves Vrus protecton n the BIOS Wrte protecton for flash EPROM Casng access montorng System lock, ncludng support for hard dsk password Software access protecton LAN alarm wth heartbeat functon Vrus protecton F-Secure vrus scanner Admnstraton functons Desktop management: local admnstraton wth ServerVew Desktop management: remote admnstraton wth RemoteVew PRIMERGY ECONEL 30 Power supply wth montor output - Power supply wth swtched montor output X System Montorng Temperature montorng Cover montorng System status dsplay X X X X X X X X X X X X X X X X X 2 A26361-K831-Z

7 Notatonal conventons Your PRIMERGY ECONEL Notatonal conventons The meanngs of the symbols and fonts used n ths manual are as follows:! CAUTION! ndcates nformaton whch s mportant for your health or for preventng physcal damage. ndcates mportant nformaton whch s requred to use the system properly. Italcs "Quotaton marks" Text whch follows ths symbol descrbes actvtes that must be performed n the order shown. ndcates commands or menu tems ndcate names of chapters and terms that are beng emphaszed. Target group Ths operatng manual s ntended for those responsble for nstallng the hardware and ensurng that the system runs smoothly. The operatng manual contans all the nformaton requred for nstallng your PRIMERGY ECONEL 30. To understand the dfferent expanson optons, you need a knowledge of hardware and data transmsson, as well as basc knowledge of the operatng system used. A26361-K831-Z

8

9 Important notes In ths chapter you wll fnd nformaton regardng safety whch t s essental to take note of when workng wth your server. Safety! CAUTION! Pay attenton to the nformaton provded n the "Safety and Ergonomcs" manual and n the followng safety notes. Durng nstallaton and before operatng the devce, please observe the nstructons on envronmental condtons n the "Techncal data" chapter as well as the nstructons n the "Preparng for use" chapter. You may only operate the devce, f the rated voltage for the devce s set to the local mans voltage. Check the rated voltage set for ths devce (see the "Preparng for use" chapter). The man swtch and the ON/OFF button do not dsconnect the server from the mans voltage. To completely dsconnect the mans voltage, remove the power plug from the grounded mans outlet. Remove the power plug before openng the unt. Replace the lthum battery on the system board n accordance wth the nstructons n the "Extensons to the system board" - "Replacng lthum battery" chapter. Cauton, components n the system can get very hot. Energy savng, dsposal and recyclng Further nformaton can be found on the CD provded wth your computer. CE markng The shpped verson of ths devce comples wth the requrements of the EEC drectves 89/336/EEC "Electromagnetc compatblty" and 73/23/EEC "Low voltage drectve". A26361-K831-Z

10 Important notes Transportng the server FCC Class B Complance Statement The followng statement apples to the products covered n ths manual, unless otherwse specfed heren. The statement for other products wll appear n the accompanyng documentaton. NOTE: Ths equpment has been tested and found to comply wth the lmts for a "Class B" dgtal devce, pursuant to Part 15 of the FCC rules and meets all requrements of the Canadan Interference- Causng Equpment Regulatons. These lmts are desgned to provde reasonable protecton aganst harmful nterference n a resdental nstallaton. Ths equpment generates, uses and can radate rado frequency energy and, f not nstalled and used n strct accordance wth the nstructons, may cause harmful nterference to rado communcatons. However, there s no guarantee that nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recepton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the followng measures: Reorent or relocate the recevng antenna. Increase the separaton between equpment and the recever. Connect the equpment nto an outlet on a crcut dfferent from that to whch the recever s connected. Consult the dealer or an experenced rado/tv techncan for help. Fujtsu Semens Computers GmbH s not responsble for any rado or televson nterference caused by unauthorzed modfcatons of ths equpment or the substtuton or attachment of connectng cables and equpment other than those specfed by Fujtsu Semens Computers GmbH. The correcton of nterference caused by such unauthorzed modfcaton, substtuton or attachment wll be the responsblty of the user. The use of shelded I/O cables s requred when connectng ths equpment to any and all optonal perpheral or host devces. Falure to do so may volate FCC rules. Transportng the server! CAUTION! Transport all parts separately n ther orgnal packagng or n a packagng whch protects them from knocks and jolts, to the new ste. Do not unpack them untl all transportaton maneuvers are completed. Cleanng the server! CAUTION! Turn off all power and equpment swtches and pull the power plug out of the grounded mans outlets. Do not clean any nteror parts yourself, leave ths job to a servce techncan. Do not use any cleanng agents that contan abrasves or may corrode plastc. Ensure that no lqud enters the system. Wpe the casng wth a dry cloth. If partcularly drty, use a cloth that has been mostened n mld domestc detergent and then carefully wrung out. Use dsnfectant wpes to clean the keyboard and the mouse. 6 A26361-K831-Z

11 Preparng for use! CAUTION! Please take note of the safety nformaton n the "Important notes" chapter. Unpackng and checkng the delvery It s recommended not to throw away the orgnal packagng materal! It may be requred for reshpment at some later date. Unpack all the ndvdual parts. Check the delvery for damage ncurred durng transportaton. Check whether the delvery agrees wth the detals n the delvery note. Should you dscover that the delvery does not correspond to the delvery note, notfy your local sales outlet mmedately. Steps for ntal setup Only a few steps are necessary to put your new server nto operaton for the frst tme: Select locaton for server and set up server Connect the montor, mouse and keyboard Check the voltage at the mans outlet and connect the server to an electrcal outlet. Swtch the server on You wll learn more about the ndvdual steps n the followng sectons External devces If you have receved other devces n addton to your server (e.g. a prnter or a modem), do not connect these untl after the ntal nstallaton. The followng sectons contan a descrpton of how to connect these external devces: "Connectng external devces to the seral port" and "Connectng external devces to the parallel port". Drves and boards If you have receved drves or boards wth your server, please do not nstall them untl after frst-tme setup. How to nstall drves and boards s descrbed n the "System expansons" chapter. A26361-K831-Z

12 Preparng for use Settng up the server Settng up the server! CAUTION! When nstallng your server, gve consderaton to the recommendatons and safety notes n the "Safety and Ergonomcs" booklet. Set up the server only n ts correct orentaton. The ponts to observe are llustrated on the followng pages. We recommend that you place your devce on a surface wth good ant-slp qualtes. In vew of the multtude of dfferent fnshes and varnshes used on furnture, t s possble that the rubber feet wll mark the surface they stand on. Do not expose the server to extreme envronmental condtons (see "Techncal data" chapter). Provde at least 200 mm of clearance n front of, to the left of, and behnd the ventlator area of the server to ensure adequate ventlaton. In order to avod overheatng, do not cover the ventlaton area of the montor or the server. Do not place several servers one above the other. Connect the montor, mouse and keyboard The ports for the montor, mouse, and keyboard are on the rear of the server (see "Ports on the server" chapter). Connectng the montor Follow the nstructons contaned n the montor manual to prepare the montor for operaton (e.g. connectng cables). 1 2 Dependng on the connector, plug the montor's power cable nto ether the server (1) or the mans outlet (2). 8 A26361-K831-Z

13 Connect the montor, mouse and keyboard Preparng for use! It s recommended to connect the montor power cable to the server montor socket. The montor s then swtched off automatcally when you swtch the server off. The montor s not swtchng off wth the system f t s connected to a mans outlet. Swtch off the montor wth ts own ON/OFF button. CAUTION! The montor power cable may only be connected to the server montor socket f the montor current consumpton s smaller than 1,5 A wth 230 V or 3 A wth 115 V. The values for the montor current consumpton can be found n the techncal data on the montor or n the operatng manual for the montor. Plug the data cable nto the montor port of the server. Connectng the mouse Dependng on the equpment level selected, your server wll be suppled wth a PS/2 mouse or a USB mouse. Connectng a PS/2 mouse Connect the PS/2 mouse to the PS/2 mouse port of the server. Connectng USB mouse Connect the USB mouse to the USB port of the server. If you do not attach a mouse at the PS/2 mouse port, you can dsable the mouse controller n the BIOS Setup n order to free the IRQ12 for a dfferent applcaton. Connectng a keyboard Dependng on the equpment level selected, your server wll be suppled wth a standard keyboard or a USB keyboard. Connectng standard keyboard Use the suppled keyboard cable only. Plug the other end of the keyboard cable (square plug) nto the socket on the undersde of the keyboard. Plug the round plug of the keyboard cable nto the keyboard port on the server. Connectng USB keyboard Use the suppled keyboard cable only. Plug the other end of the keyboard cable (square plug) nto the socket on the undersde of the keyboard. Insert the rectangular USB plug of the keyboard cable nto the USB port of the server. A26361-K831-Z

14 Preparng for use Connectng the server to the mans voltage Connectng the server to the mans voltage The server s equpped wth a man swtch and a wde range power supply. Ths means that manual voltage settng s not necessary. CAUTION!! The wde-range power supply automatcally sets tself to the correct voltage wthn the range from 100 V to 240 V. Ensure that the local mans voltage s wthn the range of 100 V to 240 V. 2 1 Connect the power cable to the server (1). Plug the power plug nto the grounded mans outlet (2). 10 A26361-K831-Z

15 Intal swtch-on: Software wll be nstalled Preparng for use Intal swtch-on: Software wll be nstalled If the server s connected to a network, the network protocol s requred as well as the user and server detals. Contact your network admnstrator f you have any questons about these settngs. When you swtch on your server for the frst tme, the suppled software s nstalled and confgured. You should plan some tme for ths, as ths process must not be nterrupted.! CAUTION! Once the nstallaton has been started the server must not be swtched off! Durng nstallaton the server may only be rebooted when you are requested to do so! Otherwse the nstallaton wll be not be performed correctly. If a fault occurs durng the nstallaton, the contents of the hard dsk must be completely restored. You may requre the Wndows lcense number durng nstallaton. Ths number s located on a stcker on your server. Swtchng on montor and server Swtch the montor on (see the operatng manual for the montor). Swtch your server on. To do ths, follow the nstructons below. Addtonally to the ON/OFF button on the front a man swtch at the rear of the server s avalable. A26361-K831-Z

16 Preparng for use Intal swtch-on: Software wll be nstalled 1 0 I 2 1 = Man swtch 2 = ON/OFF button 0 = Server s swtched off I = Server s ready-to-operate Swtch the server on wth the man swtch at the rear of the server (1). Press the ON/OFF button on the front of the server (2). The relevant ndcators on the server lght (see "Indcators on the server" chapter). 12 A26361-K831-Z

17 Installng the software Preparng for use Installng the software Insert the ServerStart CD and a possbly exstng confguraton floppy dsk and restart the server. Follow the nstructons n "Confguraton wth ServerStart" chapter. Durng nstallaton, follow the nstructons on screen. Consult the operatng system manual f there s anythng unclear about the requested nput data. Further nformaton about the system, drvers, utltes, updates, manuals etc., s contaned on the "ServerStart" and "ServerBooks" CDs. Confguraton wth ServerStart ServerStart s a powerful tool for settng up your new PRIMERGY server ServerStart lets you quckly and smoothly confgure and nstall hardware, the operatng system, and addtonal components. The ServerStart advantage Automatcally confgure your server hardware and dsk arrays Receve nstallaton help for all leadng server operatng systems Create confguraton fles for the unattended nstallaton of several PRIMERGY servers wth dentcal hardware confguratons Install drvers and addtonal software Whch software can be nstalled depends on the hardware confguraton of your server. Ths confguraton s automatcally detected. A26361-K831-Z

18 Preparng for use Installng the software Usng ServerStart The ServerStart user nterface s dvded nto two areas. All the menus for the applcaton can be quckly found n the Tree Vew area on the left. In the User Frame area on the rght you can navgate the underlned objects just as you would wth an nternal browser. Installaton procedure n ServerStart Wth help of ServerStart you can carry out the frst nstallaton of your server and perform later adjustments. Preparaton To nstall your PRIMERGY server and operatng system, you need to boot the server from the ServerStart-CD. In some crcumstances you wll need to adjust several settngs to do ths: For CD-ROM drves on a IDE bus: Ensure that the correspondng IDE channel s actvated n the BIOS of the system board and that the CD-ROM drve s the frst boot devce n the boot sequence (see ndex entry boot sequence n the BIOS-Setup manual). 14 A26361-K831-Z

19 Installng the software Preparng for use Selectng the desred nstallaton mode To set up a sngle server: It s recommended to confgure ServerStart n Guded Mode on the target system. Compared to the Expert Mode, ths offers ncreased securty by recognton and confguraton of the hardware. Contnue wth the "Installaton n Guded Mode" chapter. If you decde to nstall n Expert Mode, you wll need to know the hard dsk capacty and how to remove cards and confgure hard dsks. To set up several servers wth dentcal hardware confguratons: In ths case, create a target confguraton fle on a floppy dsk ether n the Preparaton Mode or usng the example n the Guded Mode. Contnue wth "Replcated nstallaton of several servers (Wndows)" chapter. Only one boot system can be selected n the Preparaton Mode and n the Guded Mode, and only one RAID array can be set as a boot devce. If the capacty of the boot drve cannot be determned, select the "Automatc" opton for an optmal parttonng. Guded nstallaton of a sngle server Installaton n Guded Mode In Guded Mode, nstallaton assstants confgure your server hardware and dsk arrays and then nstall the operatng system and ntegrated applcatons. For the new nstallaton, standard settngs are loaded from a Default Confguraton Fle. Ths confguraton fle can be found on the ServerStart- CD and may be edted by the admnstrator. Proceed as follows: Swtch the server on and nsert the ServerStart CD nto the drve. Swtch the server off and on agan. ServerStart wll now be started from the CD-ROM on the target system. After the boot process the ServerStart user nterface appears. Select the nstallaton mode and follow the nstallaton process n the User Frame. A hardware analyss of the target system s performed. Confguraton data s gathered for the nstallaton. After the confguraton defnton has been completed, the nstallaton phase s ntated wthout any addtonal restart. Data carrers wth the operatng system, Servce packs, and addtonal applcatons are then requred to start the nstallaton. The rest of the nstallaton process ncludng all necessary restarts executes wthout any nput from the user. Excepton: Necessary specfcatons that were not made n the confguraton phase wll be requested durng the nstallaton. A26361-K831-Z

20 Preparng for use Installng the software Durng the nstallaton of Wndows NT/2000 and NetWare 5, ServerStart also automatcally ntegrates drvers for system components that are not contaned n the operatng system. Durng the nstallaton of other operatng systems, ServerStart notfes the user of the mssng drvers. If necessary the user can now make a drver nstallaton floppy dsk. Alternatve nstallaton n Expert Mode In contrast to the Dsk and RAID Wzards n the Guded Mode, the Expert Mode lets you drectly confgure the hardware usng the tools specfcally from the manufacturer: Wndows NT Dsk Admnstrator, Global Flash ServcePartton Manager, DuplexData Partton Manager Mylex GAM (Global Access Manager), Storage Manager In connecton wth the confguraton n the Expert Mode, the operatng system nstallaton can be performed analogously to the Guded Mode. To update BIOS, frmware, and drvers wth the Global Flash Tool, you wll need a servce partton. You can set ths up convenently usng the Dsk Wzard from ServerStart. 16 A26361-K831-Z

21 Installng the software Preparng for use Replcated nstallaton of several servers (Wndows) Step 1: Makng a boot drve n the Preparaton Mode In ths operatng mode wth the help of the nstallaton assstants, you can create adapted confguraton fles for the unattended nstallaton of your PRIMERGY server. You can also set up nstallaton floppy dsks wth all the detected confguraton defntons after the confguraton of the target system n Guded Mode and n Expert Mode. Proceed as follows: The Preparaton Mode starts f ServerStart was nstalled as an applcaton on an arbtrary Wndows server Because ths computer s not necessarly the target system, no automatc hardware analyss can take place. You wll need to manually fll n the necessary nformaton (LAN topology, computer name, IP address). Fll n the requred nformaton n the correspondng menus.! CAUTION! It s mportant to correctly specfy the boot drve: Whch SCSI devce s the boot drve for the SCSI controller (SCSI-ID)? How many drves are avalable for a RAID array and whch RAID level (0/1/5) should be used? Other devces such as graphcs cards or network hardware are automatcally detected and nstalled on the target system. After the confguraton has been completed, save the gathered nformaton n an arbtrary fle wth the *.n extenson ether on the hard dsk or on a floppy dsk. Ths fle can be reopened at a tme and modfed from wthn confguraton user nterface. In ths way you can store several confguraton records for varous target systems. In order to nstall a correspondng target system based on the gathered confguraton data, you need to create va ServerStart a boot floppy dsk and copy the confguraton fle to ths floppy dsk under the flename SerStartBatch.n. A26361-K831-Z

22 Preparng for use Connectng external devces Step 2: Confguraton of the target system n Replcaton Mode Proceed as follows: In the BIOS for the system board and SCSI adapter, defne the boot sequence such that the CD-ROM drve precedes the floppy dsk drve (see the BIOS-Setup manual). Wth the confguraton floppy dsk n the drve, boot the target system from the ServerStart CD. ServerStart starts n Replcaton Mode and the nstallaton runs automatcally based on the confguraton fle. Devce drvers needed to operate the detected hardware components wll be reported and pre nstalled on the selected operatng system.! CAUTION! To successfully nstall n Replcaton Mode, the confguraton data must agree wth the hardware confguraton on the target system. Interventon n the nstallaton process s only necessary to change carrers (operatng system, servce packs, applcatons) and n the event of an ncorrect or ncomplete hardware recognton. Installaton s completed. Connectng external devces! CAUTION! Read the documentaton on the external devce before connectng t. The power plug must be removed before connectng external devces, apart from devces wth USB nterfaces. Do not ether connect or dsconnect cables durng storms. Always take hold of the actual plug. Never unplug a cable by pullng the cable tself. Connect and dsconnect the cables n the order descrbed below. Connectng cables Turn off all power and equpment swtches. Remove all power plugs from the mans outlets. Plug all cables nto the server and perpherals. You must observe the nformaton provded n the "Important notes" chapter. Plug all data communcaton cables nto the utlty sockets. Plug all power cables nto the grounded mans outlets. 18 A26361-K831-Z

23 Connectng external devces Preparng for use Dsconnectng cables Turn off all power and equpment swtches. Remove all power plugs from the mans outlets. Unplug all data communcaton cables from the utlty sockets. Dsconnect all cables at the server and at the perpherals. Devces wth USB nterfaces are hot-pluggable. Ths allows cables from these devces to be connected and dsconnected wth the system swtched on. Addtonal nformaton can be found n the "Connectng external devces to the USB port" secton and n the documentaton for the correspondng devces. Ports on the server The ports for external devces are on the rear of the server. The ports avalable on your Server depend on the confguraton level you have selected. The standard ports are marked wth the symbols shown below (or smlar). Exact detals of the poston of the ports are suppled n the techncal manuals for the boards. Keyboard port, purple PS/2 mouse port, green 1 Seral port 1, teal or turquose 2 Seral port 2, teal or turquose Montor port, blue Parallel port/prnter, burgundy Headphones port, orange or lght green Audo output (Lne out), lght green Game port, gold Mcrophone jack, pnk or red Audo nput (Lne n), lght blue SCSI connecton USB - Unversal Seral Bus, black LAN LAN connector Some of the devces that you connect requre specal drvers (see the operatng system and devce documentaton). A26361-K831-Z

24 Preparng for use Connectng external devces Connectng external devces to the seral port External devces can be connected to the seral port (e.g. a modem). Connect the data cable to the external devce. Connect the data cable to the seral port. For an exact descrpton of how to connect external devces to the seral port, please refer to the devce documentaton. Settngs of the seral port If you need to change the settngs of the seral port (e.g. address, nterrupt), you can do so n the BIOS Setup. The settngs for the port are descrbed n the techncal manual for the system board or n the "BIOS Setup" manual. Devce drvers The devces connected to the seral port requre drvers. Your operatng system already ncludes many drvers. Nevertheless, f the drver you need s not on the hard dsk, please nstall t from the data carrer suppled wth the devce or wth the applcaton program. Connectng external devces to the parallel port External devces can be connected to the parallel port (e.g. a prnter). Connect the data cable to the external devce. Connect the data cable to the parallel port. For an exact descrpton of how to connect external devces to the parallel port, please see the devce documentaton. Settngs of the parallel port If you need to change the settngs of the parallel port (e.g. address, nterrupt), you can do so n the BIOS Setup. The settngs for the port are descrbed n the techncal manual for the system board or n the "BIOS Setup" manual. Devce drvers The devces connected to the parallel port requre drvers. Your operatng system already ncludes many drvers. Nevertheless, f the drver you need s not on the hard dsk, please nstall t from the data carrer suppled wth the devce or wth the applcaton program. 20 A26361-K831-Z

25 Connectng external devces Preparng for use Connectng external devces to the USB port You can connect a wde range of external devces to the USB port (e.g. prnter, scanner, modem or keyboard). Devces wth USB nterfaces are hot-pluggable. Ths allows cables from those devces to be connected and dsconnected wth the system swtched on. Addtonal nformaton can be found n the documentaton for the correspondng devces. Connect the data cable to the external devce. Connect the data cable to the USB port. Devce drvers The devces you connect to the USB port usually requre no drver of ther own, as the requred software s already ncluded n the operatng system. However, f the devce requres ts own software, please nstall t from the data carrer provded wth the devce. A26361-K831-Z

26

27 Operaton Swtchng the server on If necessary, swtch the montor on (see the operatng manual for the montor). Swtch the server on wth the man swtch at the rear of the server. Press the ON/OFF button on the front of the server. The power-on ndcator lghts green (see "Indcators on the server" chapter) and the server s started. Swtchng the server off Shut down the operatng system properly. If the server operatng system does not swtch off automatcally, use the ON/OFF button to swtch off the server when requested. Swtch the server off at the man swtch.! CAUTION! The man swtch and the ON/OFF button do not dsconnect the server from the mans voltage. To completely dsconnect the mans voltage, remove the power plug from the socket. If necessary, swtch the montor off (see the operatng manual for the montor). Placng a server (wth soft power off functon) n a ready-to-operate state by means of software Wth the soft power off functon the server automatcally swtches off (standby) or swtches nto the energy-savng mode after the operatng system s shut down. Requrements: Your system must support swtchng off wth software and ths functonalty must be enabled n BIOS Setup. The soft power off software may also need to be nstalled on Wndows NT systems. You can also swtch your server nto the standby mode va ServerVew- and/or RemoteVew. A26361-K831-Z

28 Operaton Indcators on the server Indcators on the server The ndcators are on the front of the server. Whch ndcators are avalable on your server depends on the confguraton level you have selected = Power-on ndcator 2 = Hard dsk ndcator 3 = CD-ROM ndcator 4 = Floppy dsk ndcator 1 - Power-on ndcator The ndcator lghts green: The server s on. The ndcator lghts orange: The server s n energy-savng mode. After beng swtched on, the server returns to the state t was n before the energy-savng mode. CAUTION!! In an energy-savng mode the server must not be swtched off wth the man swtch or dsconnected from the mans supply, as ths may result n data loss. The ndcator does not lght up: The server s swtched off (man swtch at 0 or dsconnected from the power supply). 2 - Hard dsk ndcator The ndcator lghts up when the hard dsk drve of the server s accessed. 24 A26361-K831-Z

29 Keyboard Operaton 3 - CD-ROM ndcator The ndcator lghts up when the CD-ROM drve of the server s accessed. You may only remove the CD when the ndcator s dark. 4 - Floppy dsk ndcator The ndcator lghts up when the floppy dsk drve of the server s accessed. You may only remove the floppy dsk when the ndcator s unlt. Keyboard = Functon keys 2 = ON/OFF button (optonal) 3 = Alphanumerc keypad 1 = Cursor keys 2 = Numerc keypad (calculator keypad) The llustrated keyboard s an example and may dffer from the model you use. Important keys and key combnatons The followng descrpton of keys and key combnatons refers to MS Wndows. Detals of other keys and key combnatons can be found n the documentaton of the relevant applcaton program. ON/OFF button (optonal) Dependng on the settng n the BIOS Setup, the system can be swtched on, off, or on and off wth ths button. Some operatng systems allow you to confgure addtonal functons of the ON/OFF button n the Control Panel. On some keyboards the ON/OFF button can only be used wth ACPI. Otherwse the key s noperatve. The system board must support ths functon. Enter key confrms the marked selecton. The enter key s also referred to as the "Return" key. A26361-K831-Z

30 Operaton Keyboard Start key calls up the Wndows Start menu. Menu key nvokes the menu for the marked tem (Wndows). Shft key enables upper-case letters and the upper key symbols to be used. Alt Gr Alt Gr (e.g. German keyboard) produces a character shown on the rght-hand sde of a key (e.g. the on the key [Q]). Num Lock Ctrl Num Lock key by pressng the Num Lock key you swtch between the Numerc keypad cursor control functons and dgt or comma functons. When the Num Lock ndcator s lt the dgt and comma keys are actve. When the Num Lock ndcator s not lt the cursor control functons are actve n the Numerc keypad. Ctrl key starts key combnaton actons. The [Ctrl] key s also called "Control" or "Control key". Ctrl Alt Del Warm boot restarts your server. Press smultaneously the keys [Ctrl] + [Alt] + [Del]. Under some operatng systems the Task Manager appears frst. Then you must press all three keys agan to reboot. 26 A26361-K831-Z

31 Workng wth floppy dsks Operaton Workng wth floppy dsks Follow the nstructons suppled by the vendor of the floppy dsks. Never clean the floppy dsk drves wth cleanng floppy dsks. Any attempt would destroy the read/wrte head n the dsk drve wthn 20 seconds = Inserton drecton 2 = Label area 3 = Wrte protecton tab for a 1.44 Mbyte floppy dsk 4 = Identfcaton of a 1.44 MB floppy dsk or wrte protect swtch on a 120 MB floppy dsk 5 = Eject button for nserted floppy dsks 6 = Floppy dsk s wrte-protected 7 = Floppy dsk s not wrte-protected To nsert a floppy dsk: Push the floppy dsk nto the drve n the nserton drecton (1) untl t engages. The label should be facng upward. To remove a floppy dsk: Push the eject button (5). Protect the floppy dsk aganst beng overwrtten or erased Slde the wrte-protect slder nto poston (6). The hole s now vsble. Deactvate wrte protecton Slde the wrte-protect slder nto poston (7). The hole s now covered. A26361-K831-Z

32 Operaton Settngs n BIOS Setup Settngs n BIOS Setup In BIOS Setup you can set the system functons and the hardware confguraton of the server. When the server s delvered, the default entres are vald (see "BIOS Setup" manual and f necessary techncal manual for the system board). You may customze these settngs to your requrements n the BIOS Setup. Property and data protecton Software functons and mechancal lockng offer a broad range of functons for protectng your server and your personal data from unauthorzed access. You can also combne these functons. Ant-theft protecton and lead-sealng There are three ways to protect your server from theft: wth the Kensngton Lock devce (3) and wth a Kensngton McroSaver wth a chan (lead-seal) wth a (pad)lock To prevent unauthorzed persons from openng the casng, the casng can be sealed. To do ths, feed the sealng chan through the large eye (1) and the small eye (2) and seal the chan wth the lead seal. You can also attach a padlock to the large eye (1) to prevent unauthorzed openng of the casng. You can also use ths eye to anchor the casng f necessary. a 1 = Large eye 2 = Small eye 3 = Devce for "Kensngton Lock" 28 A26361-K831-Z

33 Property and data protecton Operaton BIOS setup securty functons The Securty menu n BIOS Setup offers you varous optons for protectng your personal data aganst unauthorzed access, e.g.: Preventng unauthorzed BIOS Setup entry Preventng unauthorzed system access Preventng unauthorzed access to the settngs of boards wth ther own BIOS Preventng system bootng from the floppy dsk drve Actvatng vrus warnngs Preventng unauthorzed wrtng of floppy dsks Protectng BIOS from beng overwrtten Protectng the server from beng swtched on by an external devce You can also combne these functons. You wll fnd a detaled descrpton of the Securty menus and how to assgn passwords n the techncal manual for the system board or n the "BIOS Setup" manual. A26361-K831-Z

34

35 Troubleshootng and tps! CAUTION! Take note of the safety notes n the "Safety and Ergonomcs" manual and n the "Preparng for use" chapter, when you connect or dsconnect cables. If a fault occurs, try to correct t as descrbed n the followng places: n ths chapter n the documentaton of the connected devces n the help systems of the software used n the documentaton of your operatng system If you fal to correct the problem, proceed as follows: Swtch the server off. Make a note of the steps and the crcumstances that led to the fault. Make a note of any error messages dsplayed. Note the ID number of your devce. Ths number can be found on the type ratng plate on the back of the casng. Contact your sales outlet or our customer servce center. Installng new software When nstallng programs or drvers, mportant fles may be overwrtten and modfed. To be able to access the orgnal data n the event of any problems followng nstallaton, you should backup your hard dsk pror to nstallaton. Power-on ndcator remans unlt after you have swtched on your devce Ths may be due to the followng: The mans voltage supply s faulty Check whether the power cable s plugged properly nto the server and mans outlet. Swtch your server on. Internal power supply overloaded Pull the power plug of the server out of the mans outlet. Wat for a moment. Plug the power plug nto the grounded mans outlet agan. Swtch your server on. A26361-K831-Z

36 Troubleshootng and tps The screen stays blank If your screen remans blank ths may be due to the followng: Montor s swtched off Swtch your montor on. Power savng has been actvated (screen s blank) or Press any key on the keyboard. Deactvate the screen saver. Enter the approprate password. Brghtness control s set to dark Adjust the brghtness control. For detaled nformaton, please refer to the operatng manual suppled wth your montor. Power cable not connected Swtch off the montor and the server. Check that the montor power cable s properly connected to the montor and, dependng on the connector, to the server or to a grounded mans outlet. Check whether the power cable of the server s properly connected to the server and to the mans outlet. Swtch on the montor and the server. Montor cable not connected Swtch off the montor and the server. Check that the montor cable s properly connected to the server and montor. Swtch on the montor and the server. Wrong montor has been set under Wndows 2000 Reboot the server. If the message Startng Wndows appears, press functon key [F8]. The Wndows 2000 Advanced Optons Menu appears. Select Safe Mode or Safe Mode wth Network. Set the correct values for the attached montor as descrbed n the operatng manual of the montor by selectng Start - Settngs - Control Panel - Dsplay - Settngs. 32 A26361-K831-Z

37 Troubleshootng and tps Wrong montor has been set under Wndow XP Reboot the server. Press [F8] whle the system s bootng. Ether the Wndows Advanced Start Optons menu or the menu for selectng the operatng system appears. If the menu for selectng the operatng system appears, press [F8]. Select Safe Mode or Safe Mode wth Network. Set the correct values for the attached montor as descrbed n the operatng manual of the montor by selectng Start - Settngs - Control Panel - Dsplay and then the Appearance, Themes, Settngs tabs. The wrong RAM modules have been nserted See the techncal manual for the system board for nformaton on whch memory modules can be used. No mouse ponter dsplayed on the screen Shut down the operatng system properly. Swtch the server off. Check that the mouse cable s properly connected to the system unt. If you use an adapter or extenson lead wth the mouse cable, check the connectons. Make sure that only one mouse s connected. Swtch your server on. The mouse controller must be enabled f you use a PS/2 mouse on the PS/2 mouse port. Check n the BIOS Setup that the mouse controller s Enabled. Check that the mouse drver s properly nstalled and s present when the applcaton program s started. Detaled nformaton can be found n the user gude for the mouse and applcaton program. The floppy dsk cannot be read or wrtten Check that the wrte protecton of the floppy dsk or the floppy dsk drve s actvated (refer to the "BIOS Setup" manual and f necessary to the techncal manual for the system board). Check the entry for Floppy dsk A n the Man menu of the BIOS Setup. Check that the floppy dsk drve controller s enabled (also refer to the techncal manual for the system board or to the "BIOS Setup" manual). Check that the cables of the floppy dsk drve are properly connected (refer to "Changng the floppy dsk drve" chapter). A26361-K831-Z

38 Troubleshootng and tps Tme and/or date s not correct You can set the tme and date n the BIOS Setup or n the operatng system. Set the tme and date. If the tme and date are repeatedly wrong when you swtch on your server, the on-board battery s flat. Change the lthum battery as descrbed n the "Extensons to the system board" - "Replacng lthum battery" chapter. Error messages on the screen Error messages and ther explanaton are contaned: n the techncal manual for the system board n the "BIOS Setup" manual n the documentaton for the programs used Restorng the hard dsk contents Should you need to restore your hard dsk, the nstructons are provded on the case of the "Recovery CD" (delvered wth your system). Tps The server cannot be swtched off wth the ON/OFF button Cause: The server has not been swtched on wth the ON/OFF button. Press the ON/OFF button agan. Cause: System crash Press and hold the ON/OFF button for at least four seconds untl the server swtches off. Out of system resources If you have too many applcatons runnng at once, you may experence problems due to a lack of system resources. In ths case you should: or close unnecessary applcatons run the applcatons n a dfferent order Other manuals Other manuals are contaned on the "Drvers & Utltes" CD. 34 A26361-K831-Z

39 System expansons! CAUTION! It may be necessary to update the BIOS when carryng out a system expanson or hardware upgrade. Addtonal nformaton s contaned n the "BIOS Setup" manual or possbly n the techncal manual for the system board. When nstallng components that become very hot, make sure that the maxmum permssble temperatures of the ndvdual components are not exceeded. The server must be swtched off when nstallng/removng the system expansons and may not be n the energy-savng mode. Remove the power plug before openng the server. Ths chapter descrbes all the actvtes requred to modfy your server hardware (e.g. nstallng boards or drves). Read the suppled documentaton before nstallng new drves and/or boards. Refer to the techncal manual for the system board before makng any extensons to the system board. Informaton about boards Take care wth the lockng mechansms (catches and centerng pns) when you are replacng boards or components on boards. To prevent damage to the board or the components and conductors on t, please take care when you nsert or remove boards. Make sure expanson boards are nserted straghtly. Never use sharp objects (screwdrvers) for leverage. Boards wth electrostatc senstve devces (ESD) are dentfable by the label shown. When you handle boards ftted wth ESDs, you must, under all crcumstances, observe the followng ponts: You must statcally dscharge yourself before workng wth boards (e.g. by touchng a grounded object). The equpment and tools you use must be free of statc charges. Pull out the power plug before nsertng or removng boards. Always hold boards wth ESDs by ther edges. Never touch pns or conductors on boards ftted wth ESDs. A26361-K831-Z

40 System expansons Openng the casng Openng the casng Swtch the server off. The server must not be n the energy-savng mode.! CAUTION! Please take note of the safety nformaton n the "Important notes" chapter. Pull the power plug out of the mans outlet. Only nsert the power plug after you have closed the casng. Remove any connected cables n the unt that obstruct you. Place the devce n a convenent workng poston. 2 1 Press the green unlockng button on the rear of the casng (1). Hold the green unlockng button depressed and slde the casng sde cover upwards n the drecton of the arrow (2). Pull the sde cover out of the casng. 36 A26361-K831-Z

41 Closng the casng System expansons Closng the casng 1 Push the sde cover from above n the drecton of the arrow (1) untl t engages. Return the system unt to ts orgnal poston. Reconnect any dsconnected cables (power cord, cables to external devces, etc.). A26361-K831-Z

42 System expansons Installng and removng a board Installng and removng a board! CAUTION! Please take note of the "Informaton about boards". The number, poston and arrangement of the board slots on the system board can be found n the techncal manual for the system board. Boards may already be nstalled when the devce s shpped. Installng a board Open the casng (see "Openng the casng") Press the unlockng mechansm (1) down and open the lockng ral (2). The word "PRESS" s embossed on the unlockng mechansm. Remove the slot cover from the slot (3).! CAUTION! Do not dspose of the slot cover. For coolng, protecton aganst fre and n order to comply wth EMC regulatons, you must reft the slot cover f you remove the board. Take the new board out of ts packagng. Make the requred settngs for the board. 38 A26361-K831-Z

43 Installng and removng a board System expansons Push the board up to ts slot (1). Press the board nto the slot so that t engages. If necessary, connect the cables. Close the lockng ral (2) and press on the lockng mechansm n the drecton of the arrow (3). The word "PUSH" s embossed on the lockng mechansm. Close the casng (see "Closng the casng"). If you have nstalled or removed a PCI board, please check the relevant PCI slot settngs n the BIOS Setup. If necessary, change the settngs. Further nformaton s provded n the PCI board documentaton. The slots 1, 3, 5 and 7 are sutable for low-profle cards wth an adapter. The slots are counted from the bottom to the top. A26361-K831-Z

44 System expansons Installng and removng a board Removng a board Open the casng (see "Openng the casng"). Dsconnect the cables connected to the board Press the unlockng mechansm (1) down and open the lockng ral (2). The word "PRESS" s embossed on the unlockng mechansm. Pull the board out of the slot (3). Place the board nto approprate packagng.! CAUTION! For coolng, protecton aganst fre, and n order to comply wth EMC (electromagnetc compatblty) regulatons, you must reft the slot cover. 40 A26361-K831-Z

45 Installng and removng a board System expansons 1 a 3 2 Push the slot cover nto the slot (1).! CAUTION! Ensure that the projecton (a) on the slot cover engages nto the approprate recess. If t does not, you wll fnd t dffcult to close the lockng ral. There s a danger of damage. Close the lockng ral (2) and press on the lockng mechansm n the drecton of the arrow (3). The word "PUSH" s embossed on the lockng mechansm. Close the casng (see "Closng the casng"). If you have nstalled or removed a PCI board, please check the relevant PCI slot settngs n the BIOS Setup. If necessary, change the settngs. Further nformaton s provded n the PCI board documentaton. A26361-K831-Z

46 System expansons Low-Profle boards Low-Profle boards For unts wth a partcularly low overall heght, there are so-called low-profle boards wth a slot cover wth a lower overall heght to match the low-profle unts. To also nstall these low-profle boards n normal board slots, you must mount a correspondng slot adapter beforehand Two-pece rear covers are ftted nto the slots ntended for low-profle boards. The two peces are connected together wth a screw. Remove the desred rear cover and then remove the screw. Mountng slot adapter 1 Ft the slot adapter on the slot cover of the low-profle board (1) and screw t on (2). Now you can nstall the low-profle board n a sutable slot lke a normal board (see the chapter "Installng board"). 2 Removng slot adapter 2 Unscrew the screw (1) and remove the slot adapter (2) A26361-K831-Z

47 Low-Profle boards System expansons Installng and removng drves The server casng can accommodate a total of eght drves: four accessble drves (three 5¼" drves and one 3½" drve) four non-accessble drves (3½" drves) "Accessble drves" are e.g. DVD or CD ROM drves, nto whch a data carrer can be nserted from outsde. Non-accessble drves are e.g. hard dsk drves. IDE drves Four IDE drves are supported as standard equpment. Ideally, hard dsk drves are connected to IDE nterface 1 and other drves to IDE nterface 2 (see also the techncal manual for the system board). SCSI drves If you want to nstall a SCSI drve, you requre a SCSI controller and a SCSI cable. Detals are provded n the manuals on the SCSI controller Removng the front panel Open the casng (see "Openng the casng"). Detach the unlockng lever (1) and open the front panel (2) Detach the plastc hook on the front panel of the casng and carefully remove the front panel. If you pull too hard, you may loosen or damage the LCD cable. A26361-K831-Z

48 System expansons Low-Profle boards Attachng the front panel Engage the lockng mechansm on the rght of the casng. Attach the front panel on the casng such that the plastc hooks engage nto the correct recesses. Close the front panel (1) and make sure that the LCD cable s not pnched and that the lockng mechansms engage notceably (2) A26361-K831-Z

49 Low-Profle boards System expansons Installng an accessble drve Open the casng (see "Openng the casng"). Remove the front (see "Removng the front panel"). 1 1 Press the EasyChange rals (1) together and pull the empty slde-n module out of the casng (2). A26361-K831-Z

50 System expansons Low-Profle boards Pull the EasyChange rals off the empty slde-n module. Do not dspose of the empty slde-n module. For coolng, protecton aganst fre, and n order to comply wth EMC regulatons, you must reft the empty slde-n module f you remove the drve agan later. Take the new drve out of ts packagng. Adjust the requred settngs on the drve (f necessary, on already-nstalled drves as well). Press the EasyChange rals nto the provded holes. Push the accessble drve nto the casng untl the EasyChange rals engage. Plug the data and the power supply connectors nto the drve. Make sure the polarty s correct. 46 A26361-K831-Z

51 Low-Profle boards System expansons Attach the front panel (see "Attachng the front panel"). Close the casng (see "Closng the casng"). Wth the upper three accessble drves, the EasyChange ral s attached at the bottom of the module. The ral s attached at the center of the module on the lowest drve. All rals are mounted correctly on delvery. It may be necessary to modfy the entry for the drve n the BIOS Setup. Removng an accessble drve Open the casng (see "Openng the casng"). Remove the front (see "Removng the front panel"). 1 1 Pull the data and the power supply connectors from the desred drve. Press the EasyChange rals together (1) and pull the drve out of the casng (2). If necessary, make the requred settngs on the remanng hard dsk drve. A26361-K831-Z

52 System expansons Low-Profle boards Pull the EasyChange rals off the drve. Press the EasyChange rals nto the holes provded n the empty slde-n module. 48 A26361-K831-Z

53 Low-Profle boards System expansons Slde the slde-n module nto the casng untl t engages notceably. Attach the front panel (see "Attachng the front panel"). Close the casng (see "Closng the casng"). It may be necessary to modfy the entry for the remanng drves n the BIOS Setup. A26361-K831-Z

54 System expansons Low-Profle boards Changng the floppy dsk drve Open the casng (see "Openng the casng"). Remove the front (see "Removng the front panel"). Dsconnect the cables connected to the floppy dsk drve. Removng the floppy dsk drve 1 1 Press the EasyChange rals n the drecton of the arrows (1). Pull the floppy dsk drve slde-n module out of the casng (2). Pull the EasyChange rals off the floppy dsk drve slde-n module. 50 A26361-K831-Z

55 Low-Profle boards System expansons 1 1 Remove the screws (1) on both sdes of the slde-n module. Pull the floppy dsk drve out of the slde-n module (2). Installng the floppy dsk drve Take the new floppy dsk drve out of ts packagng. 2 2 Slde the floppy dsk drve nto the slde-n module (1). Fasten the floppy dsk drve wth the screws (2) on both sdes of the slde-n module. A26361-K831-Z

56 System expansons Low-Profle boards Press the EasyChange rals nto the provded holes. Slde the floppy dsk drve slde-n module nto the casng (1) untl t engages notceably. Ft the data and power supply connectors to the floppy dsk drve. Attach the front panel (see "Attachng the front panel"). Close the casng (see "Closng the casng"). It may be necessary to modfy the entry for the drve n the BIOS Setup. 52 A26361-K831-Z

57 Low-Profle boards System expansons Installng or removng the hard dsk drve Open the casng (see "Openng the casng"). Removng the cover 1 2 Undo the screw (1). Fold out the cover (2). A26361-K831-Z

58 System expansons Low-Profle boards Installng a hard dsk drve Take the new hard dsk drve out of ts packagng. Make the requred settngs (e.g. master-slave settngs) on the drve. Secure the EasyChange rals on the sde of the hard dsk drve by nsertng the upper pns of the EasyChange ral n the correspondng holes of the hard dsk drve. 1 Push the hard dsk drve nto the casng (1) untl the EasyChange rals engage. Connect the data and power supply cables to the hard dsk drve or to the hard dsk drves. Connect the blue plug of the data cable to the connecton on the system board. Connect the plug on the other end to the hard dsk drve. 54 A26361-K831-Z

59 Low-Profle boards System expansons Installng the cover plate 2 1 a a Set the cover plate nto the casng such that the projectons (a) engage nto the approprate recesses (1). Close the cover and fasten t wth the screw (2). Close the casng (see "Closng the casng"). It may be necessary to modfy the entry for the drve n the BIOS Setup. A26361-K831-Z

60 System expansons Low-Profle boards Removng a hard dsk drve Open the casng (see "Openng the casng"). Remove the cover (see "Removng the cover"). Dsconnect all cables connected to the drve (data cable, power supply cable) Press the EasyChange rals n the drecton of the arrows (1). Take the hard dsk drve out of the carrer (2). Pull the EasyChange rals off the hard dsk drve. If necessary, make the requred settngs on the remanng hard dsk drve. Install the cover plate (see "Installng the cover plate"). Close the casng (see "Closng the casng"). It may be necessary to modfy the entry for the drve n the BIOS Setup. 56 A26361-K831-Z

61 Extensons to the system board System expansons Extensons to the system board Detals on whether you can upgrade the man memory or the processor are provded n the techncal manual for the system board. In order to upgrade or replace the processor, you must frst remove the ventlaton cover. Open the casng (see "Openng the casng"). Removng the power supply 1 2 Unscrew the screw wth whch the power supply s secured n the casng (1). Swng the power supply out of the casng as far as t wll go (2).! CAUTION! Only connect the power plug after you have renstalled the power supply and closed the unt. Upgradng man memory Upgrade the memory accordng to the descrpton n the techncal manual for the system board. Close the casng (see "Closng the casng"). Replacng processor Upgrade the processor accordng to the descrpton n the techncal manual for the system board. A26361-K831-Z

62 System expansons Extensons to the system board Replacng lthum battery In order to permanently save the system nformaton, a lthum battery s nstalled to provde the CMOS-memory wth a current. A correspondng error message notfes the user when the charge s too low or the battery s empty. The lthum battery must then be replaced.! CAUTION! Incorrect replacement of the lthum battery may lead to a rsk of exploson! The lthum battery may be replaced only wth an dentcal battery or wth a type recommended by the manufacturer. Do not throw lthum batteres nto the household waste. They must be dsposed of n accordance wth local regulatons concernng specal waste. Make sure that you nsert the battery the rght way round. The plus pole must be on the top! 2 3 Press the lockng lug n the drecton of the arrow; the battery jumps somewhat out of the holder (1). Remove the battery (2). Push the new lthum battery of the dentcal type nto the holder (3) and press t downward untl t engages (4). Swngng the power supply n Swng the power supply nto the casng untl t meets the stop. Fasten the power supply n the casng wth the screw. 58 A26361-K831-Z

63 Techncal data Electrcal data Regulatons compled wth: EN / VDE 0805 UL 1950 CSA 22.2 No.950 Protecton class: I Rated voltage range (automatc, 300 W power 100 V V supply) Frequency: 50 Hz - 60 Hz Max. rated current Server wth montor outlet:100 V V / 7,0 A 200 V V / 3,5 A Montor socket (output): 100 V V / 3.0 A 200 V V / 1,5 A Dmensons Wdth/depth/heght: 205 mm/504 mm/385 mm Weght wth the basc confguraton approx. 15 kg Envronmental condtons Envronment class (3K2) Envronment class (2K2) Temperature: Operatng (3K2) Transport (2K2) Condensaton n operatng must be avoded. Clearance requred to ensure adequate ventlaton: left front rear DIN IEC 721 part 3-3 DIN IEC 721 part C C -25 C C mn. 200 mm mn. 200 mm mn. 200 mm The data sheet of the server contans further techncal data. You wll fnd the data sheet ether on the "ServerStart" CD suppled or on the Internet at: A26361-K831-Z

64

65 Index 3 1/2-nch drve /4-nch drve 43 A Alt Gr key 26 Ant-theft protecton 28 Audo nput 19 Audo output 19 B Battery 58 BIOS Setup 28 securty functons 29 system settngs 28 Board 35 nstallng 38 removng 38, 40 C Cable connectng 18 dsconnectng 19 Casng closng 37 lead-sealng 28 lockng 37 openng 36 CD-ROM drve ndcator 25 nstallng 45 removng 47 CE certfcate 5 Chan 28 Class B Complance Statement 6 Confguraton BIOS Setup 28 ServerStart 13 Contents of delvery 7 Control key 26 Ctrl key 26 Ctrl+Alt+Del 26 Cursor keys 25 D Data protecton 28 Date, not correct 34 Devce drvers parallel port 20 seral port 20 USB 21 Devces connectng 18, 20, 21 ports 19 wth USB port 21 Devces wth USB port, software 21 Dsposal 5 Drve 43 accessble 43 nstallng 43, 45 non-accessble drve 43 removng 43, 47 E Electromagnetc compatblty 5 Energy savng 5 Enter key 25 Ergonomcs 8 Error date 34 floppy dsk 33 message 34 mouse 33 screen 32 server 31 tme 34 ESD 35 Extensons server 35 system board 57 External devces connectng 18, 20, 21 ports 19 F FCC statement 6 Floppy dsk cannot read 33 cannot wrte 33 nsertng 27 removng 27 wrte-protecton 27, 33 wrte-protecton, dsablng 27 Floppy dsk drve changng 50 ndcator 25 nstallng 51, 52 removng 50 Floppy dsk ndcator 25 Functon keys 25 A26361-K831-Z

66 Index G Game port 19 H Hard dsk contents, restorng 34 Hard dsk drve ndcator 24 nstallng 53, 55 removng 53, 56 Hard dsk ndcator 24 Headphones, port 19 I IDE drve 43 Installaton ServerStart 14 swtchng on for the frst tme 11 Installng, software 11, 13 Interfaces 19 K Kensngton Lock 28 Key Alt Gr 26 Control key 26 Ctrl 26 Ctrl key 26 Ctrl+Alt+Del 26 Enter key 25 Menu key 26 Num Lock 26 Return key 25 Shft 26 Shft key 26 Start key 26 Key combnaton 25, 26 Keyboard 25 connectng 9 mportant keys 25 port 9, 19 Keypad, alphanumerc 25 L LAN port 19 Lead-sealng 28 Lne n 19 Lne out 19 Lthum battery 57 replacng 58 Low-profle boards 42 mountng slot adapter 42 removng slot adapter 42 M Man memory 57 upgradng 57 Man swtch 12 Manuals, further 34 Memory nsuffcent 34 not enough 34 Menu key 26 Mcrophone jack 19 Montor cleanng 6 connectng 8 remans blank 32 transportng 6 Montor screen, no screen dsplay 32 Mouse connectng 9 error 33 ponter 33 port 19 N New nstallaton, software 31 New software, nstallng 31 Notatonal conventons 3 Note boards 35 CE certfcate 5 mportant 5 Num Lock key 26 Numerc keypad 25 O ON/OFF button 12 P Packng materal 7 unpackng 7 Parallel port 19 connectng devces 20 settngs 20 Port audo nput 19 audo output 19 game port 19 headphones 19 keyboard 19 LAN 19 lne n 19 lne out 19 mcrophone 19 montor 19 mouse A26361-K831-Z

67 Index Port parallel port 19 prnter 19 PS/2 mouse 19 SCSI 19 seral port 19 USB 19 Power supply, removng 57 Power-on ndcator 12, 13, 24 dark 31 fals to lght 24, 31 lghts green 24 lghts orange 24 Preparng for frst use, overvew 7 Preparng for use 7 overvew 7 Prnter 19 Processor 57 Property protecton 28 Protecton, property and data 28 PS/2 mouse connectng 9 port 9, 19 R Ready-to-operate 12 Recyclng 5 Retransportaton 6 Return key 25 S Safety 5 SCSI drve 43 SCSI port 19 Securty functons, BIOS Setup 29 Seral port 19, 20 connectng devces 20 port 19 settngs 20 Server ant-theft protecton 28 cablng 18 cannot boot 31 checkng rated voltage 10 cleanng 6 closng 37 connectng 10 connectng devces 18 extensons 35 ndcator 24 lead-sealng 28 lockng 37 openng 36 ports 19 Server ready for operaton 23 settng up 8 soft power off 23 swtchng off 23 swtchng off, wth man swtch 23 swtchng on 11, 23 swtchng on, wth man swtch 23 transportng 6 ServerStart Expert Mode 16 Guded Mode 15 nstallaton 14 nstallaton mode 15 Preparaton Mode 17 Replcaton Mode 18 usng 14 Setup, see BIOS Setup Shft key 26 Sgns and symbols 3 Soft power off 23 Software nstallng 11, 13 new nstallaton 31 Standard keyboard, connectng 9 Start key 26 Streamer nstallng 45 removng 47 Summer tme 34 System board, extensons 57 System expanson 35 System settngs, BIOS Setup 28 T Target group 3 Techncal data 59 Tme daylght savngs 34 not correct 34 Tps 31, 34 Transport 6 Trouble floppy dsk 33 mouse 33 screen 32 server 31 Troubleshootng 31 U USB keyboard, connectng 9 USB mouse, connectng 9 USB port 9, 19, 21 connectng devces 21 A26361-K831-Z

68 Index V Ventlaton area 8 Vdeo workstaton 8 W Warm boot 26 Wrte protecton, floppy dsk 27, A26361-K831-Z

69 Informaton on ths document On Aprl 1, 2009, Fujtsu became the sole owner of Fujtsu Semens Computers. Ths new subsdary of Fujtsu has been renamed Fujtsu Technology Solutons. Ths document from the document archve refers to a product verson whch was released a consderable tme ago or whch s no longer marketed. Please note that all company references and copyrghts n ths document have been legally transferred to Fujtsu Technology Solutons. Contact and support addresses wll now be offered by Fujtsu Technology Solutons and have the The Internet pages of Fujtsu Technology Solutons are avalable at and the user documentaton at Copyrght Fujtsu Technology Solutons, 2009 Hnwese zum vorlegenden Dokument Zum 1. Aprl 2009 st Fujtsu Semens Computers n den allengen Bestz von Fujtsu übergegangen. Dese neue Tochtergesellschaft von Fujtsu trägt setdem den Namen Fujtsu Technology Solutons. Das vorlegende Dokument aus dem Dokumentenarchv bezeht sch auf ene berets vor längerer Zet fregegebene oder ncht mehr m Vertreb befndlche Produktverson. Btte beachten Se, dass alle Frmenbezüge und Copyrghts m vorlegenden Dokument rechtlch auf Fujtsu Technology Solutons übergegangen snd. Kontakt- und Supportadressen werden nun von Fujtsu Technology Solutons angeboten und haben de De Internetseten von Fujtsu Technology Solutons fnden Se unter und unter fnden Se de Benutzerdokumentaton. Copyrght Fujtsu Technology Solutons, 2009