GXR-GPS GXR-GPS-485 User Manual

Transcription

1 GXR-GPS GXR-GPS-485 User Mnul GeoSIG Ltd, Wiesenstrsse 39, 8952 Schlieren, Switzerlnd Phone: , Fx: info@geosig.com,

2 Pge ii Document Revision GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Author Checked Approved Ricrdo Arujo Rlph Boeniger Dr. Tlhn Biro Version Action First Issue (RA) Revision for User Mnul nd formtting (TB) Pictures Fig.4 nd 10 replced by ctul ones (THL) Updte with GXR-GPS-485 (ANB) Updte comments in tble 4 Disclimer GeoSIG Ltd reserves the right to chnge the informtion contined in this document without notice. While the informtion contined herein is ssumed to be ccurte, GeoSIG Ltd ssumes no responsibility for ny errors or omissions. Copyright Notice No prt of this document my be reproduced without the prior written consent of GeoSIG Ltd. The softwre described in this document is furnished under license nd my only be used or copied in ccordnce with the terms of such license. Trdemrk All brnd nd product nmes mentioned re trdemrks or registered trdemrks of their respective holders. All rights reserved. GeoSIG Ltd Switzerlnd

3 GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Tble of Contents Pge iii 2.1. GPS Min Connector Pin Assignment Mting Connector t the Instrument Side Cble Connection GXR-GPS Cble Connection GXR-GPS Mounting the GPS Box With GSR-xx With CR-5P... 8

4 Pge iv Wrnings nd Sfety GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul The GPS system is operted by the government of the United Sttes of Americ, which is solely responsible for its ccurcy nd mintennce. GPS provides only UTC time t 0 Greenwich meridin without summer time djustment. Symbols nd Abbrevitions Instrument GPS UTC GeoSIG Recorder, Digitiser or Dt Acquisition system Globl Positioning System Coordinted Universl Time

5 GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Pge 1 1. Introduction This document describes the principle of opertion nd instlltion instructions of the GXR-GPS GPS fmily, which is GPS module bsed on Grmin GPS type GPS-35-HVS. GXR-GPS is used with GeoSIG Instruments to provide the globl coordintes of the GPS ntenn nd ccurte dte nd time to the Instruments. It s very useful for hving one or severl interconnected Instruments precisely synchronised. GPS provides only UTC time t 0 Greenwich meridin without summer time djustment. GXR-GPS is provided in box with cble length to be defined t the time of order or provided by the customer. Upto 70 m cble length is possible with the stndrd GXR-GPS, upto m with the optionl GXR-GPS-485. All instructions within this User Mnul lso pply to the GXR-GPS-485, whenever only GXR-GPS is mentioned. GeoSIG stndrd cble type: XY DIN 5 x 0.25 mm2 gr UL style2464. Figure 1. GXR-GPS ssembled with 20 m of cble for n Instrument

6 Pge 2 2. Electricl Connection GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul 2.1. GPS Min Connector Pin Assignment The GXR-GPS is provided with n 8 pin min connector inside the box. Before connecting the connector, the cble should be pssed through the cble inlet ssembled on the housing. The cble end sleeves should be used for proper connection of the cble on the connector. Tble 1. Electricl connections of the GXR-GPS connector Pin Signl Stndrd cble colors Comment 1 GPS_RXD White Trnsmit signl of GSR 2 GPS_TXD Brown Reception signl of GSR 3 GPS_1PPS Green 1 PPS signl from GPS 4 V_MAIN Yellow 12V power from instrument 5 GPS_STDBY N/A Usully not connected 6 GND Grey Ground from instrument 7 GND N/A Usully not connected 8 GND N/A Usully not connected Tble 2. Electricl connections of the GXR-GPS-485 connector Pin Signl Stndrd cble colors Comment 1 TX_H White Trnsmit signl of CR-5P 2 RX_H N/A Usully not connected 3 TX_L Brown Reception signl of CR-5P 4 RX_L N/A Usully not connected 5 GPS_SYNC Green 1 PPS signl from GPS 6 V_MAIN Yellow 12V power from instrument 7 GND Grey Ground from instrument 8 GND N/A Usully not connected Figure 2. Connector pin out GXR-GPS Figure 3. Connector pin out GXR-GPS-485 Figure 4. Connector wiring GXR-GPS Figure 5. Connector wiring GXR-GPS-485

7 GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Pge Mting Connector t the Instrument Side For connecting the GXR-GPS to n Instrument, mting connector must be used. This connector is provided with the Instrument. With GSR-xx, the connector must be connected to the OPTION connector of the instrument, if not otherwise specified. With CR-5P, the connector must be connected to the SYN in connector of the instrument. Tble 3. Electricl connections of the GXR-GPS input connector of n instrument Pin Signl Stndrd Cble Colors Comment 1 GSR_G_TXD White Trnsmit signl of GSR 2 GSR_G_RXD Brown Reception signl of GSR 3 N/A N/A Not connected 4 N/A N/A Not connected 5 GSR_G_1PPS Green 1 PPS signl from GPS 6 GSR_G_12V Yellow 12V power from instrument 7 GSR_G_GND Grey Ground from instrument Tble 4. Electricl connections of the GXR-GPS-485 input connector of n instrument Pin Signl Stndrd Cble Colors Comment 1 N/A N/A Not connected 2 SYNCI_RX+ White GPS Trnsmit signl+ 3 N/A N/A Not connected 4 SYNCI_RX- Brown GPS Trnsmit signl- 5 GPS_1PPS Green 1 PPS signl from GPS 6 V_EXT_GPS Yellow 12V power from instrument 7 GND_EXT Grey Ground from instrument Figure 6. Mting Binder connector Figure 7. Connector pin out Figure 8. Wiring inside the connector

8 Pge Cble Connection GXR-GPS GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul A B C D E xx Shrinkble tubing 9 to 3 mm GSN: #RE090.BLK.001 Schrinkble tubing 3 to 1 mm GSN: #RE030.BLK Connection to GS_GPSA_J1 Cble Connecton to GSR Housing Type: Isolted cble end sleeve 0.25 mm2 x 6 mm GSN: 5x #PD IN Type: Dtcble DIN 5x0.25 mm2, d = 11 mm, no shield, length: xx m GSN: #CA Type: Binder Serie 693, 7 P, M GSN: #J_CIR M 1 GSR_G_TXD white 2 GSR_G_RXD brown 3 GSR_G_1PPS green 4 GSR_G_12V yellow 6 GSR_G_GND grey G_TX_H 2 G_RX_H G_485_T_L - G_485_R_L GPS_SYNC GPS_POWER GND white brown green yellow grey Revision: * Size: A3 Scle: 1:1 File: GS_GPS_Box_Cble.skf Dte: Version: 0 Unit: mm Remrk: Drwn by: MS Project : GS_GPS Checked by: RB Title : GPS Box, GPS Cble Approved by: CHK Pge: 1 of A B C D E - Figure 9. Cble connection GXR-GPS

9 GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Pge Cble Connection GXR-GPS-485 A B C D E Pod insulted GSN: #PD IN Shrinkble tubbing 3 mm GSN: #RE030.BLK.001 Shrinkble tubbing 6 mm Shrinkble tubbing 6 mm GSN: #RE060.BLK.001 GSN: #RE060.BLK.001 Connector Cble Connector Type: Binder, 7p, Mle Type: GPS cble, 25 m grey, XY DIN 5x0.25 gu UL Style 2464 Type: BLA 8 SN OR, 8p GSN: #J_CIR M GSN: #CA GSN: #J_WIR F 1 SYNCI_1PPS+ NC 1 TX_H white 2 SYNCI_RX+ white 2 RX_H NC 3 SYNCI_1PPS- NC 3 TX_L brown SYNCI_RX- brown RX_L NC 5 GSR_1PPS green 5 GPS_SYNC green 6 V_EXT_GPS yellow 6 V_MAIN yellow 7 GND_EXT grey 7 GND grey 8 GND NC Remrks: Move the cble to cross the glnd before to screw the connector wiedmuller Revision: - Version: 0 Size: A3 Scle: 1:1 Unit: mm Dte: File: GXR-GPS-485.SKF Drwn by: TL Project : GS_CR5P Checked by: Title : GPS RS-485 Cble Approved by: CHK Pge: 1 of A B C D E Figure 10. Cble connection GXR-GPS-485

10 Pge Mounting the GPS Box GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul It is recommended to perform check of the GPS function before mounting the box to its finl loction, s described in section 3. The GXR-GPS box cn be fixed to vrious loctions. The position of the box should be defined ccording to position where GPS ntenn cn esily get the stellite signls. Typiclly the box is fixed on n outside wll or on roof. This is n importnt point since for the synchronistion of the instrument, the ntenn should receive t lest signls from 3 stellites. Mke sure tht t lest 75% of the sky is visible t ll times over the GPS box. Fixtion of the housing should be done with M4 screws. With spcings nd loctions s shown in Figure 11, Figure 12 nd Figure 13. Type of screws depends on the type of surfce where box is going to be fixed. Figure 11. Mechnicl fixtion of housing Figure 12. Inside view of the GXR-GPS housing Figure 13. Inside view of the GXR-GPS-485 housing

11 GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul Pge 7 3. Configurtion nd Checking 3.1. With GSR-xx In order to synchronise GeoSIG GSR-xx with the GPS, pproprite configurtion should be mde in the Instrument. Once power supply, computer nd GPS re connected to the Instrument, such configurtion nd checks cn be performed using GeoDAS nd logging into the Instrument. For more detils bout the GPS options, plese consult GeoDAS nd relevnt Instrument mnuls. At first instlltion or fter mjor (>2 000 km) reloction, it my tke upto 5 minutes for the GPS to correctly compute the exct loction of the ntenn. The following is brief recipe to check whether everything is opertionl in terms of the GPS: On Instrument tb, Grmin GPS option should be ticked s peripherl device s shown on Figure 14. On the Dte nd Time tb, s shown on Figure 15,GPS sttus should red Enbled, if not, press the Enble GPS button. Note tht if GPS is enbled, this button reds Disble GPS. When GPS is synchronised, the dte nd time of the GPS cn be seen in the Dte nd Time tb nd the globl coordintes of the GPS ntenn cn be seen in the Sttion tb, s shown on Figure 16. Figure 14. Selecting GPS s peripherl device Figure 15. GPS enbling nd checking Figure 16. GPS time nd position checking

12 Pge With CR-5P GS_GXR_GPS_User_Mnul_V05.doc / GPS User Mnul In order to synchronise GeoSIG CR-5P with the GPS, pproprite configurtion should be mde in the Instrument. Once power supply, computer nd GPS re connected to the Instrument, such configurtion nd checks cn be performed using GeoDAS nd logging into the Instrument. For more detils bout the GPS options, plese consult GeoDAS nd relevnt Instrument mnuls. At first instlltion or fter mjor (>2 000 km) reloction, it my tke upto 5 minutes for the GPS to correctly compute the exct loction of the ntenn. The following is brief recipe to check whether everything is opertionl in terms of the GPS: While dding the CR-5P under Chnnels of Digitizers, mke sure Externl SYNC Signl is selected s Time source, s shown in Figure 17. After dding the CR-5P to GeoDAS restrt the Softwre nd the Window Sttions: Dt Strem will pper. When GPS is synchronised, the GPS sttus will red Locked to GPS, s shown in Figure 18. The Dt Strem in the Dt Monitor will be in yellow, s shown in Figure 19. Note tht if no GPS is connected, GPS sttus will red No Lock nd the colour of the Dt Strem will be white. Figure 17. Set Externl SYNC Signl s Time source Figure 18. GPS sttus s Locked to GPS Figure 19. Dt Strem is in yellow